A remote device in security mode 3 that tries to connect will require
the pairing during the connection setup phase. The disconnect timeout
is now triggered within 10 milliseconds and causes the pairing to fail.
If a connection is not fully established and a PIN code request is
received, don't trigger the disconnect timeout. The either successful
or failing connection complete event will make sure that the timeout
is triggered at the right time.
The biggest problem with security mode 3 is that many Bluetooth 2.0
device and before use a temporary security mode 3 for dedicated
bonding.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johan Hedberg <johan.hedberg@nokia.com>
The connection setup phase takes around 2 seconds or longer and in
that time it is possible that the need for an ACL connection is no
longer present. If that happens then, the connection attempt will
be canceled.
This only applies to outgoing connections, but currently it can also
be triggered by incoming connection. Don't call hci_acl_connect_cancel()
on incoming connection since these have to be either accepted or rejected
in this state. Once they are successfully connected they need to be
fully disconnected anyway.
Also remove the wrong hci_acl_disconn() call for SCO and eSCO links
since at this stage they can't be disconnected either, because the
connection handle is still unknown.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johan Hedberg <johan.hedberg@nokia.com>
The module refcount is increased by hci_dev_hold() call in hci_conn_add()
and decreased by hci_dev_put() call in del_conn(). In case the connection
setup fails, hci_dev_put() is never called.
Procedure to reproduce the issue:
# hciconfig hci0 up
# lsmod | grep btusb -> "used by" refcount = 1
# hcitool cc <non-exisiting bdaddr> -> will get timeout
# lsmod | grep btusb -> "used by" refcount = 2
# hciconfig hci0 down
# lsmod | grep btusb -> "used by" refcount = 1
# rmmod btusb -> ERROR: Module btusb is in use
The hci_dev_put() call got moved into del_conn() with the 2.6.25 kernel
to fix an issue with hci_dev going away before hci_conn. However that
change was wrong and introduced this problem.
When calling hci_conn_del() it has to call hci_dev_put() after freeing
the connection details. This handling should be fully symmetric. The
execution of del_conn() is done in a work queue and needs it own calls
to hci_dev_hold() and hci_dev_put() to ensure that the hci_dev stays
until the connection cleanup has been finished.
Based on a report by Bing Zhao <bzhao@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Bing Zhao <bzhao@marvell.com>
This fixes the use of fwmarks to denote IPv4 virtual services
which was unfortunately broken as a result of the integration
of IPv6 support into IPVS, which was included in 2.6.28.
The problem arises because fwmarks are stored in the 4th octet
of a union nf_inet_addr .all, however in the case of IPv4 only
the first octet, corresponding to .ip, is assigned and compared.
In other words, using .all = { 0, 0, 0, htonl(svc->fwmark) always
results in a value of 0 (32bits) being stored for IPv4. This means
that one fwmark can be used, as it ends up being mapped to 0, but things
break down when multiple fwmarks are used, as they all end up being mapped
to 0.
As fwmarks are 32bits a reasonable fix seems to be to just store the fwmark
in .ip, and comparing and storing .ip when fwmarks are used.
This patch makes the assumption that in calls to ip_vs_ct_in_get()
and ip_vs_sched_persist() if the proto parameter is IPPROTO_IP then
we are dealing with an fwmark. I believe this is valid as ip_vs_in()
does fairly strict filtering on the protocol and IPPROTO_IP should
not be used in these calls unless explicitly passed when making
these calls for fwmarks in ip_vs_sched_persist().
Tested-by: Fabien DuchĂȘne <fabien.duchene@student.uclouvain.be>
Cc: Joseph Mack NA3T <jmack@wm7d.net>
Cc: Julius Volz <julius.volz@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is used as a library by several device drivers,
which select INET_LRO.
If some are modules and some are statically built into the
kernel, we get build failures if INET_LRO is modular.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ashish Karkare <akarkare@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit ac45f602ee ("net: infrastructure
for hardware time stamping") added two skb initialization actions to
__alloc_skb(), which need to be added to skb_recycle_check() as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When no limit is given, the bfifo uses a default of tx_queue_len * mtu.
Packets handled by qdiscs include the link layer header, so this should
be taken into account, similar to what other qdiscs do.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new wimax_dev is created, it's state has to be __WIMAX_ST_NULL
until wimax_dev_add() is succesfully called. This allows calls into
the stack that happen before said time to be rejected.
Until now, the state was being set (by mistake) to UNINITIALIZED,
which was allowing calls such as wimax_report_rfkill_hw() to go
through even when a call to wimax_dev_add() had failed; that was
causing an oops when touching uninitialized data.
This situation is normal when the device starts reporting state before
the whole initialization has been completed. It just has to be dealt
with.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
When sending a message to user space using wimax_msg(), if nla_put()
fails, correctly interpret the return code from wimax_msg_alloc() as
an err ptr and return the error code instead of crashing (as it is
assuming than non-NULL means the pointer is ok).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
This patch fixes the wrong message type that are triggered by
user updates, the following commands:
(term1)# conntrack -I -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state LISTEN
(term1)# conntrack -U -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state SYN_SENT
(term1)# conntrack -U -p tcp -s 1.1.1.1 -d 2.2.2.2 -t 10 --sport 10 --dport 20 --state SYN_RECV
only trigger event message of type NEW, when only the first is NEW
while others should be UPDATE.
(term2)# conntrack -E
[NEW] tcp 6 10 LISTEN src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
[NEW] tcp 6 10 SYN_SENT src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
[NEW] tcp 6 10 SYN_RECV src=1.1.1.1 dst=2.2.2.2 sport=10 dport=20 [UNREPLIED] src=2.2.2.2 dst=1.1.1.1 sport=20 dport=10 mark=0
This patch also removes IPCT_REFRESH from the bitmask since it is
not of any use.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch fixes a problem when you use 32 nodes in the cluster
match:
% iptables -I PREROUTING -t mangle -i eth0 -m cluster \
--cluster-total-nodes 32 --cluster-local-node 32 \
--cluster-hash-seed 0xdeadbeef -j MARK --set-mark 0xffff
iptables: Invalid argument. Run `dmesg' for more information.
% dmesg | tail -1
xt_cluster: this node mask cannot be higher than the total number of nodes
The problem is related to this checking:
if (info->node_mask >= (1 << info->total_nodes)) {
printk(KERN_ERR "xt_cluster: this node mask cannot be "
"higher than the total number of nodes\n");
return false;
}
(1 << 32) is 1. Thus, the checking fails.
BTW, I said this before but I insist: I have only tested the cluster
match with 2 nodes getting ~45% extra performance in an active-active setup.
The maximum limit of 32 nodes is still completely arbitrary. I'd really
appreciate if people that have more nodes in their setups let me know.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits)
e1000: fix virtualization bug
bonding: fix alb mode locking regression
Bluetooth: Fix issue with sysfs handling for connections
usbnet: CDC EEM support (v5)
tcp: Fix tcp_prequeue() to get correct rto_min value
ehea: fix invalid pointer access
ne2k-pci: Do not register device until initialized.
Subject: [PATCH] br2684: restore net_dev initialization
net: Only store high 16 bits of kernel generated filter priorities
virtio_net: Fix function name typo
virtio_net: Cleanup command queue scatterlist usage
bonding: correct the cleanup in bond_create()
virtio: add missing include to virtio_net.h
smsc95xx: add support for LAN9512 and LAN9514
smsc95xx: configure LED outputs
netconsole: take care of NETDEV_UNREGISTER event
xt_socket: checks for the state of nf_conntrack
bonding: bond_slave_info_query() fix
cxgb3: fixing gcc 4.4 compiler warning: suggest parentheses around operand of â!â
netfilter: use likely() in xt_info_rdlock_bh()
...
As packets ending with NEXTHDR_NONE don't have a last extension header,
the check for the length needs to be after the check for NEXTHDR_NONE.
Signed-off-by: Christoph Paasch <christoph.paasch@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Due to a semantic changes in flush_workqueue() the current approach of
synchronizing the sysfs handling for connections doesn't work anymore. The
whole approach is actually fully broken and based on assumptions that are
no longer valid.
With the introduction of Simple Pairing support, the creation of low-level
ACL links got changed. This change invalidates the reason why in the past
two independent work queues have been used for adding/removing sysfs
devices. The adding of the actual sysfs device is now postponed until the
host controller successfully assigns an unique handle to that link. So
the real synchronization happens inside the controller and not the host.
The only left-over problem is that some internals of the sysfs device
handling are not initialized ahead of time. This leaves potential access
to invalid data and can cause various NULL pointer dereferences. To fix
this a new function makes sure that all sysfs details are initialized
when an connection attempt is made. The actual sysfs device is only
registered when the connection has been successfully established. To
avoid a race condition with the registration, the check if a device is
registered has been moved into the removal work.
As an extra protection two flush_work() calls are left in place to
make sure a previous add/del work has been completed first.
Based on a report by Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Justin P. Mattock <justinmattock@gmail.com>
Tested-by: Roger Quadros <ext-roger.quadros@nokia.com>
Tested-by: Marc Pignat <marc.pignat@hevs.ch>
pid doesn't count with some band having more bitrates than the one
associated the first time.
Fix that by counting the maximal available bitrate count and allocate
big enough space.
Secondly, fix touching uninitialized memory which causes panics.
Index sucked from this random memory points to the hell.
The fix is to sort the rates on each band change.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
minstrel doesn't count max rate count in fact, since it doesn't use
a loop variable `i' and hence allocs space only for bitrates found in
the first band.
Fix it by involving the `i' as an index so that it traverses all the
bands now and finds the real max bitrate count.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to lock using the cfg80211_mutex in
wiphy_apply_custom_regulatory(). Without the lock
there is possible race between processing a reply from CRDA
and a driver calling wiphy_apply_custom_regulatory(). During
the processing of the reply from CRDA we free last_request and
wiphy_apply_custom_regulatory() eventually accesses an
element from last_request in the through freq_reg_info_regd().
This is very difficult to reproduce (I haven't), it takes us
3 hours and you need to be banging hard, but the race is obvious
by looking at the code.
This should only affect those who use this caller, which currently
is ath5k, ath9k, and ar9170.
EIP: 0060:[<f8ebec50>] EFLAGS: 00210282 CPU: 1
EIP is at freq_reg_info_regd+0x24/0x121 [cfg80211]
EAX: 00000000 EBX: f7ca0060 ECX: f5183d94 EDX: 0024cde0
ESI: f8f56edc EDI: 00000000 EBP: 00000000 ESP: f5183d44
DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
Process modprobe (pid: 14617, ti=f5182000 task=f3934d10 task.ti=f5182000)
Stack: c0505300 f7ca0ab4 f5183d94 0024cde0 f8f403a6 f8f63160 f7ca0060 00000000
00000000 f8ebedf8 f5183d90 f8f56edc 00000000 00000004 00000f40 f8f56edc
f7ca0060 f7ca1234 00000000 00000000 00000000 f7ca14f0 f7ca0ab4 f7ca1289
Call Trace:
[<f8ebedf8>] wiphy_apply_custom_regulatory+0x8f/0x122 [cfg80211]
[<f8f3f798>] ath_attach+0x707/0x9e6 [ath9k]
[<f8f45e46>] ath_pci_probe+0x18d/0x29a [ath9k]
[<c023c7ba>] pci_device_probe+0xa3/0xe4
[<c02a860b>] really_probe+0xd7/0x1de
[<c02a87e7>] __driver_attach+0x37/0x55
[<c02a7eed>] bus_for_each_dev+0x31/0x57
[<c02a83bd>] driver_attach+0x16/0x18
[<c02a78e6>] bus_add_driver+0xec/0x21b
[<c02a8959>] driver_register+0x85/0xe2
[<c023c9bb>] __pci_register_driver+0x3c/0x69
[<f8e93043>] ath9k_init+0x43/0x68 [ath9k]
[<c010112b>] _stext+0x3b/0x116
[<c014a872>] sys_init_module+0x8a/0x19e
[<c01049ad>] sysenter_do_call+0x12/0x21
[<ffffe430>] 0xffffe430
=======================
Code: 0f 94 c0 c3 31 c0 c3 55 57 56 53 89 c3 83 ec 14 8b 74 24 2c 89 54 24 0c 89 4c 24 08 85 f6 75
06 8b 35 c8 bb ec f8 a1 cc bb ec f8 <8b> 40 04 83 f8 03 74 3a 48 74 37 8b 43 28 85 c0 74 30 89 c6
8b
EIP: [<f8ebec50>] freq_reg_info_regd+0x24/0x121 [cfg80211] SS:ESP 0068:f5183d44
Cc: stable@kernel.org
Reported-by: Nataraj Sadasivam <Nataraj.Sadasivam@Atheros.com>
Reported-by: Vivek Natarajan <Vivek.Natarajan@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Another bug in the "cfg80211: do not replace BSS structs" patch,
a forgotten length update leads to bogus data being stored and
passed to userspace, often truncated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fragmentation threshold is defined to be including the
FCS, and the code that sets the TX_FRAGMENTED flag correctly
accounts for those four bytes. The code that verifies this
doesn't though, which could lead to spurious warnings and
frames being dropped although everything is ok. Correct the
code by accounting for the FCS.
(JWL -- The problem is described here:
http://article.gmane.org/gmane.linux.kernel.wireless.general/32205 )
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tcp_prequeue() refers to the constant value (TCP_RTO_MIN) regardless of
the actual value might be tuned. The following patches fix this and make
tcp_prequeue get the actual value returns from tcp_rto_min().
Signed-off-by: Satoru SATOH <satoru.satoh@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fixes resolved crashes due to resource leak BUG_ON checks. The
resource leaks were detected by introducing asynchronous transport errors.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Commit 0ba25ff4c6 ("br2684: convert to
net_device_ops") inadvertently deleted the initialization of the net_dev
pointer in the br2684_dev structure, leading to crashes. This patch
adds it back.
Reported-by: Mikko Vinni <mmvinni@yahoo.com>
Tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel should only be using the high 16 bits of a kernel
generated priority. Filter priorities in all other cases only
use the upper 16 bits of the u32 'prio' field of 'struct tcf_proto',
but when the kernel generates the priority of a filter is saves all
32 bits which can result in incorrect lookup failures when a filter
needs to be deleted or modified.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_socket can use connection tracking, and checks whether it is a module.
Signed-off-by: Laszlo Attila Toth <panther@balabit.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
When skb_rx_queue_recorded() is true, we dont want to use jash distribution
as the device driver exactly told us which queue was selected at RX time.
jhash makes a statistical shuffle, but this wont work with 8 static inputs.
Later improvements would be to compute reciprocal value of real_num_tx_queues
to avoid a divide here. But this computation should be done once,
when real_num_tx_queues is set. This needs a separate patch, and a new
field in struct net_device.
Reported-by: Andrew Dickinson <andrew@whydna.net>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert Buytenhek wrote:
> Since 4fb6699481 ("net: Optimize memory
> usage when splicing from sockets.") I'm seeing this oops (e.g. in
> 2.6.30-rc3) when splicing from a TCP socket to /dev/null on a driver
> (mv643xx_eth) that uses LRO in the skb mode (lro_receive_skb) rather
> than the frag mode:
My patch incorrectly assumed skb->sk was always valid, but for
"frag_listed" skbs we can only use skb->sk of their parent.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Debugged-by: Lennert Buytenhek <buytenh@wantstofly.org>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In "mac80211: correct wext transmit power handler"
I fixed the wext handler, but forgot to make the default of the
user_power_level -1 (aka "auto"), so that now the transmit power
is always set to 0, causing associations to time out and similar
problems since we're transmitting with very little power. Correct
this by correcting the default user_power_level to -1.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Bisected-by: Niel Lambrechts <niel.lambrechts@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- ieee80211_wep_init(), which is called with rtnl_lock held, blocks in
request_module() [waiting for modprobe to load a crypto module].
- modprobe blocks in a call to flush_workqueue(), when it closes a TTY
[presumably when it exits].
- The workqueue item linkwatch_event() blocks on rtnl_lock.
There's no reason for wep_init() to be called with rtnl_lock held, so
just move it outside the critical section.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The x_tables are organized with a table structure and a per-cpu copies
of the counters and rules. On older kernels there was a reader/writer
lock per table which was a performance bottleneck. In 2.6.30-rc, this
was converted to use RCU and the counters/rules which solved the performance
problems for do_table but made replacing rules much slower because of
the necessary RCU grace period.
This version uses a per-cpu set of spinlocks and counters to allow to
table processing to proceed without the cache thrashing of a global
reader lock and keeps the same performance for table updates.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Bluetooth 2.1 specification introduced four different security modes
that can be mapped using Legacy Pairing and Simple Pairing. With the
usage of Simple Pairing it is required that all connections (except
the ones for SDP) are encrypted. So even the low security requirement
mandates an encrypted connection when using Simple Pairing. When using
Legacy Pairing (for Bluetooth 2.0 devices and older) this is not required
since it causes interoperability issues.
To support this properly the low security requirement translates into
different host controller transactions depending if Simple Pairing is
supported or not. However in case of Simple Pairing the command to
switch on encryption after a successful authentication is not triggered
for the low security mode. This patch fixes this and actually makes
the logic to differentiate between Simple Pairing and Legacy Pairing
a lot simpler.
Based on a report by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Bluetooth stack uses a reference counting for all established ACL
links and if no user (L2CAP connection) is present, the link will be
terminated to save power. The problem part is the dedicated pairing
when using Legacy Pairing (Bluetooth 2.0 and before). At that point
no user is present and pairing attempts will be disconnected within
10 seconds or less. In previous kernel version this was not a problem
since the disconnect timeout wasn't triggered on incoming connections
for the first time. However this caused issues with broken host stacks
that kept the connections around after dedicated pairing. When the
support for Simple Pairing got added, the link establishment procedure
needed to be changed and now causes issues when using Legacy Pairing
When using Simple Pairing it is possible to do a proper reference
counting of ACL link users. With Legacy Pairing this is not possible
since the specification is unclear in some areas and too many broken
Bluetooth devices have already been deployed. So instead of trying to
deal with all the broken devices, a special pairing timeout will be
introduced that increases the timeout to 60 seconds when pairing is
triggered.
If a broken devices now puts the stack into an unforeseen state, the
worst that happens is the disconnect timeout triggers after 120 seconds
instead of 4 seconds. This allows successful pairings with legacy and
broken devices now.
Based on a report by Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In 2.6.25 we added UDP mem accounting.
This unfortunatly added a penalty when a frame is transmitted, since
we have at TX completion time to call sock_wfree() to perform necessary
memory accounting. This calls sock_def_write_space() and utimately
scheduler if any thread is waiting on the socket.
Thread(s) waiting for an incoming frame was scheduled, then had to sleep
again as event was meaningless.
(All threads waiting on a socket are using same sk_sleep anchor)
This adds lot of extra wakeups and increases latencies, as noted
by Christoph Lameter, and slows down softirq handler.
Reference : http://marc.info/?l=linux-netdev&m=124060437012283&w=2
Fortunatly, Davide Libenzi recently added concept of keyed wakeups
into kernel, and particularly for sockets (see commit
37e5540b3c
epoll keyed wakeups: make sockets use keyed wakeups)
Davide goal was to optimize epoll, but this new wakeup infrastructure
can help non epoll users as well, if they care to setup an appropriate
handler.
This patch introduces new DEFINE_WAIT_FUNC() helper and uses it
in wait_for_packet(), so that only relevant event can wakeup a thread
blocked in this function.
Trace of function calls from bnx2 TX completion bnx2_poll_work() is :
__kfree_skb()
skb_release_head_state()
sock_wfree()
sock_def_write_space()
__wake_up_sync_key()
__wake_up_common()
receiver_wake_function() : Stops here since thread is waiting for an INPUT
Reported-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now we have no upper limit on the size of the route cache hash table.
On a 128GB POWER6 box it ends up as 32MB:
IP route cache hash table entries: 4194304 (order: 9, 33554432 bytes)
It would be nice to cap this for memory consumption reasons, but a massive
hashtable also causes a significant spike when measuring OS jitter.
With a 32MB hashtable and 4 million entries, rt_worker_func is taking
5 ms to complete. On another system with more memory it's taking 14 ms.
Even though rt_worker_func does call cond_sched() to limit its impact,
in an HPC environment we want to keep all sources of OS jitter to a minimum.
With the patch applied we limit the number of entries to 512k which
can still be overriden by using the rt_entries boot option:
IP route cache hash table entries: 524288 (order: 6, 4194304 bytes)
With this patch rt_worker_func now takes 0.460 ms on the same system.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When kernel inserts a temporary SA for IKE, it uses the wrong hash
value for dst list. Two hash values were calcultated before: one with
source address and one with a wildcard source address.
Bug hinted by Junwei Zhang <junwei.zhang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the VLAN event handler does not adjust the VLAN
device's carrier state when the real device or the VLAN device is set
administratively up or down.
The following patch adds a transfer of operating state from the
real device to the VLAN device when the real device is administratively
set up or down, and sets the carrier state up or down during init, open
and close of the VLAN device.
This permits observers above the VLAN device that care about the
carrier state (bonding's link monitor, for example) to receive updates
for administrative changes by more closely mimicing the behavior of real
devices.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The nfs server rdma transport was mapping rdma read target pages for
TO_DEVICE instead of FROM_DEVICE. This causes data corruption on non
cache-coherent systems if frmrs are used.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Related-to: commit 325fb5b4d2
The compat path suffers from a similar problem. It only uses a __be32
when all of the recent code uses, and expects, an nf_inet_addr
everywhere. As a result, addresses stored by xt_recents were
filled with whatever other stuff was on the stack following the be32.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
With a minor compile fix from Roman.
Reported-and-tested-by: Roman Hoog Antink <rha@open.ch>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch adds missing role attribute to the DCCP type, otherwise
the creation of entries is not of any use.
The attribute added is CTA_PROTOINFO_DCCP_ROLE which contains the
role of the conntrack original tuple.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Commit d0dba725 (netfilter: ctnetlink: add callbacks to the per-proto
nlattrs) changed the protocol registration function to abort if the
to-be registered protocol doesn't provide a new callback function.
The DCCP and UDP-Lite IPv6 protocols were missed in this conversion,
add the required callback pointer.
Reported-and-tested-by: Steven Jan Springl <steven@springl.ukfsn.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch fixes a (bogus?) gcc warning during compilation:
net/netfilter/nf_conntrack_netlink.cđą warning: 'helpname' may be used uninitialized in this function
net/netfilter/nf_conntrack_netlink.c:991: warning: 'helpname' may be used uninitialized in this function
In fact, helpname is initialized by ctnetlink_parse_help() so
I cannot see a way to use it without being initialized.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch "af_rose/x25: Sanity check the maximum user frame size"
(commit 83e0bbcbe2) from Alan Cox got
locking wrong. If we bail out due to user frame size being too large,
we must unlock the socket beforehand.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NetLabel address selector mechanism has a problem where it can get
mistakenly remove the wrong selector when similar addresses are used. The
problem is caused when multiple addresses are configured that have different
netmasks but the same address, e.g. 127.0.0.0/8 and 127.0.0.0/24. This patch
fixes the problem.
Reported-by: Etienne Basset <etienne.basset@numericable.fr>
Signed-off-by: Paul Moore <paul.moore@hp.com>
Acked-by: James Morris <jmorris@namei.org>
Tested-by: Etienne Basset <etienne.basset@numericable.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF_IUCV runs into a race when queuing incoming iucv messages
and receiving the resulting backlog.
If the Linux system is under pressure (high load or steal time),
the message queue grows up, but messages are not received and queued
onto the backlog queue. In that case, applications do not
receive any data with recvmsg() even if AF_IUCV puts incoming
messages onto the message queue.
The race can be avoided if the message queue spinlock in the
message_pending callback is spreaded across the entire callback
function.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add few more sk states in iucv_sock_shutdown().
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reject incoming iucv messages if the receive direction has been shut down.
It avoids that the queue of outstanding messages increases and exceeds the
message limit of the iucv communication path.
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If iucv_sock_recvmsg() is called with MSG_PEEK flag set, the skb is enqueued
twice. If the socket is then closed, the pointer to the skb is freed twice.
Remove the skb_queue_head() call for MSG_PEEK, because the skb_recv_datagram()
function already handles MSG_PEEK (does not dequeue the skb).
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure a second invocation of iucv_sock_close() guarantees proper
freeing of an iucv path.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In non-SMP mode, the variable section attribute specified by DECLARE_PER_CPU()
does not agree with that specified by DEFINE_PER_CPU(). This means that
architectures that have a small data section references relative to a base
register may throw up linkage errors due to too great a displacement between
where the base register points and the per-CPU variable.
On FRV, the .h declaration says that the variable is in the .sdata section, but
the .c definition says it's actually in the .data section. The linker throws
up the following errors:
kernel/built-in.o: In function `release_task':
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
kernel/exit.c:78: relocation truncated to fit: R_FRV_GPREL12 against symbol `per_cpu__process_counts' defined in .data section in kernel/built-in.o
To fix this, DECLARE_PER_CPU() should simply apply the same section attribute
as does DEFINE_PER_CPU(). However, this is made slightly more complex by
virtue of the fact that there are several variants on DEFINE, so these need to
be matched by variants on DECLARE.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When checking whether or not a given frame needs to be
moved to be properly aligned to a 4-byte boundary, we
use & 4 which wasn't intended, this code should check
the lowest two bits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is expected that config interface will always succeed as mac80211
will only request what driver supports. The exception here is when a
device has rfkill enabled. At this time the rfkill state is unknown to
mac80211 and config interface can fail. When this happens we deal with
this error instead of printing a WARN.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211: fix basic rates setting from association response"
introduced a copy/paste error.
Unfortunately, this not just leads to wrong data being passed
to the driver but is remotely exploitable for some hardware or
driver combinations.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently beacon loss detection triggers after a scan. A probe request
is sent and a message like this is printed to the log:
wlan0: beacon loss from AP 00:12:17:e7:98:de - sending probe request
But in fact there is no beacon loss, the beacons are just not received
because of the ongoing scan. Fix it by updating last_beacon after
the scan has finished.
Reported-by: Jaswinder Singh Rajput <jaswinder@kernel.org>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the code paths sending deauth/disassoc events ends up calling
this function with rcu_read_lock held, so we must use GFP_ATOMIC in
allocation routines.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove this unused Kconfig variable, which Intel apparently once
promised to make use of but never did.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
br_nf_dev_queue_xmit only checks for ETH_P_IP packets for fragmenting but not
VLAN packets. This results in dropping of large VLAN packets. This can be
observed when connection tracking is enabled. Connection tracking re-assembles
fragmented packets, and these have to re-fragmented when transmitting out. Also,
make sure only refragmented packets are defragmented as per suggestion from
Patrick McHardy.
Signed-off-by: Saikiran Madugula <hummerbliss@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This loop over fragments in napi_fraginfo_skb() was "interesting".
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just noticed while doing some new work that the recent
mid-wq adjustment logic will misbehave when FACK is not
in use (happens either due sysctl'ed off or auto-detected
reordering) because I forgot the relevant TCPCB tagbit.
Signed-off-by: Ilpo JĂ€rvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Sidorenko reported:
"while experimenting with 'netem' we have found some strange behaviour. It
seemed that ingress delay as measured by 'ping' command shows up on some
hosts but not on others.
After some investigation I have found that the problem is that skbuff->tstamp
field value depends on whether there are any packet sniffers enabled. That
is:
- if any ptype_all handler is registered, the tstamp field is as expected
- if there are no ptype_all handlers, the tstamp field does not show the delay"
This patch prevents unnecessary update of tstamp in dev_queue_xmit_nit()
on ingress path (with act_mirred) adding a check, so minimal overhead on
the fast path, but only when sniffers etc. are active.
Since netem at ingress seems to logically emulate a network before a host,
tstamp is zeroed to trigger the update and pretend delays are from the
outside.
Reported-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Tested-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been broken for a while. I happened to catch it testing because one
app "knew" that the top line of the calls data was the policy line and got
confused.
Put the header back.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom chips with 2.1 firmware handle the fallback case to a SCO
link wrongly when setting up eSCO connections.
< HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17
handle 11 voice setting 0x0060
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 1 bdaddr 00:1E:3A:xx:xx:xx type SCO encrypt 0x01
The Link Manager negotiates the fallback to SCO, but then sends out
a Connect Complete event. This is wrong and the Link Manager should
actually send a Synchronous Connection Complete event if the Setup
Synchronous Connection has been used. Only the remote side is allowed
to use Connect Complete to indicate the missing support for eSCO in
the host stack.
This patch adds a workaround for this which clearly should not be
needed, but reality is that broken Broadcom devices are deployed.
Based on a report by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtman <marcel@holtmann.org>
Some Bluetooth chips (like the ones from Texas Instruments) don't do
proper eSCO negotiations inside the Link Manager. They just return an
error code and in case of the Kyocera ED-8800 headset it is just a
random error.
< HCI Command: Setup Synchronous Connection 0x01|0x0028) plen 17
handle 1 voice setting 0x0060
> HCI Event: Command Status (0x0f) plen 4
Setup Synchronous Connection (0x01|0x0028) status 0x00 ncmd 1
> HCI Event: Synchronous Connect Complete (0x2c) plen 17
status 0x1f handle 257 bdaddr 00:14:0A:xx:xx:xx type eSCO
Error: Unspecified Error
In these cases it is up to the host stack to fallback to a SCO setup
and so retry with SCO parameters.
Based on a report by Nick Pelly <npelly@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There is a missing call to rfcomm_dlc_clear_timer in the case that
DEFER_SETUP is used and so the connection gets disconnected after the
timeout even if it was successfully accepted previously.
This patch adds a call to rfcomm_dlc_clear_timer to rfcomm_dlc_accept
which will get called when the user accepts the connection by calling
read() on the socket.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check whether the underlying device provides a set of ethtool ops before
checking for individual handlers to avoid NULL pointer dereferences.
Reported-by: Art van Breemen <ard@telegraafnet.nl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIM IE must not be shorter than 4 bytes, so verify that
when parsing it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead, allocate extra IE memory if necessary. Normally,
this isn't even necessary since there's enough space.
This is a better way of correcting the "held BSS can
disappear" issue, but also a lot more code. It is also
necessary for proper auth/assoc BSS handling in the
future.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we receive a probe response frame we can replace the
BSS struct in our list -- but if that struct is held then
we need to hold the new one as well.
We really should fix this completely and not replace the
struct, but this is a bandaid for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using the scan_sdata variable here is terribly wrong,
if there has never been a scan then we fail. However,
we need a bandaid...
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch, nfnetlink returns -ENOMEM instead of -EPERM if we
fail to create the nfnetlink netlink socket during the module
loading. This is exactly what rtnetlink does in this case.
Ideally, it would be better if we propagate the error that has
happened in netlink_kernel_create(), however, this function still
does not implement this yet.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch fixes an inconsistency that results in no error reports
to user-space listeners if we fail to allocate the event message.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
After calling skb_gro_receive skb->len can no longer be relied
on since if the skb was merged using frags, then its pages will
have been removed and the length reduced.
This caused tcp_gro_receive to prematurely end merging which
resulted in suboptimal performance with ixgbe.
The fix is to store skb->len on the stack.
Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ead2ceb0ec ("Network Drop
Monitor: Adding kfree_skb_clean for non-drops and modifying
end-of-line points for skbs") so called end-of-line points for skb's
should use consume_skb() to free the socket buffer.
In opposite to consume_skb() the function kfree_skb() is intended to
be used for unexpected skb drops e.g. in error conditions that now can
trigger the network drop monitor if enabled.
This patch moves the skb end-of-line point in af_can.c to use
consume_skb().
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The removal of the SAME target accidentally removed one feature that is
not available from the normal NAT targets so far, having multi-range
mappings that use the same mapping for each connection from a single
client. The current behaviour is to choose the address from the range
based on source and destination IP, which breaks when communicating
with sites having multiple addresses that require all connections to
originate from the same IP address.
Introduce a IP_NAT_RANGE_PERSISTENT option that controls whether the
destination address is taken into account for selecting addresses.
http://bugzilla.kernel.org/show_bug.cgi?id=12954
Signed-off-by: Patrick McHardy <kaber@trash.net>
mac80211: Fragmentation threshold (typo)
ieee80211_ioctl_siwfrag() sets the fragmentation_threshold to 2352
when frame fragmentation is to be disabled, yet the corresponding
'get' function tests for 2353 bytes instead.
This causes user-space tools to display a fragmentation threshold
of 2352 bytes even if fragmentation has been disabled.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Sunday 05 April 2009 11:29:38 Michael Buesch wrote:
> On Sunday 05 April 2009 11:23:59 Jaswinder Singh Rajput wrote:
> > With latest linus tree I am getting, .config file attached:
> >
> > [ 22.895051] r8169: eth0: link down
> > [ 22.897564] ADDRCONF(NETDEV_UP): eth0: link is not ready
> > [ 22.928047] ADDRCONF(NETDEV_UP): wlan0: link is not ready
> > [ 22.982292] libvirtd used greatest stack depth: 4200 bytes left
> > [ 63.709879] wlan0: authenticate with AP 00:11:95:9e:df:f6
> > [ 63.712096] wlan0: authenticated
> > [ 63.712127] wlan0: associate with AP 00:11:95:9e:df:f6
> > [ 63.726831] wlan0: RX AssocResp from 00:11:95:9e:df:f6 (capab=0x471 status=0 aid=1)
> > [ 63.726855] wlan0: associated
> > [ 63.730093] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
> > [ 74.296087] wlan0: no IPv6 routers present
> > [ 79.349044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 119.358200] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 179.354292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 259.366044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 359.348292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 361.953459] packagekitd used greatest stack depth: 4160 bytes left
> > [ 478.824258] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 598.813343] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 718.817292] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 838.824567] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 958.815402] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1078.848434] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1198.822913] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1318.824931] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1438.814157] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1558.827336] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1678.823011] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1798.830589] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 1918.828044] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2038.827224] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2116.517152] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2158.840243] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
> > [ 2278.827427] wlan0: beacon loss from AP 00:11:95:9e:df:f6 - sending probe request
>
>
> I think this message should only show if CONFIG_MAC80211_VERBOSE_DEBUG is set.
> It's kind of expected that we lose a beacon once in a while, so we shouldn't print
> verbose messages to the kernel log (even if they are KERN_DEBUG).
>
> And besides that, I think one can easily remotely trigger this message and flood the logs.
> So it should probably _also_ be ratelimited.
Something like this:
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Wext makes no assumptions about the contents of
data->txpower.fixed and data->txpower.value when
data->txpower.disabled is set, so do not update
the user-requested power level while disabling.
Also, when wext configures a really _fixed_ power
output [1], we should reject it instead of limiting it
to the regulatory constraint. If the user wants to set
a _limit_ [2] then we should honour that.
[1] iwconfig wlan0 txpower 20dBm fixed
[2] iwconfig wlan0 txpower 10dBm
This fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1942
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently rx status for frames which are completed from reorder buffer
is taken from it's cb area which is not always right, cb is not holding
the rx status when driver uses mac80211's non-irq rx handler to pass it's
received frames. This results in dropping almost all frames from reorder
buffer when security is enabled by doing double decryption (first in hw,
second in sw because of wrong rx status). This patch copies rx status into
cb area before the frame is put into reorder buffer. After this patch,
there is a significant improvement in throughput with ath9k + WPA2(AES).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We won't ever get here as regulatory_hint_core() can only fail
on -ENOMEM and in that case we don't initialize cfg80211 but this is
technically correct code.
This is actually good for stable, where we don't check for -ENOMEM
failure on __regulatory_hint()'s failure.
Cc: stable@kernel.org
Reported-by: Quentin Armitage <Quentin@armitage.org.uk>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit ea781f197d (netfilter: nf_conntrack: use SLAB_DESTROY_BY_RCU and)
get rid of call_rcu() was missing one conversion to the hlist_nulls
functions, causing a crash when unloading conntrack helper modules.
Reported-and-tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
commit ca735b3aaa
'netfilter: use a linked list of loggers'
introduced an array of list_head in "struct nf_logger", but
forgot to initialize it in nf_log_register(). This resulted
in oops when calling nf_log_unregister() at module unload time.
Reported-and-tested-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Eric Leblond <eric@inl.fr>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This reverts commit 244f46ae6e.
Alan Cox did the research, and just like the other radio protocols
zero-length frames have meaning because at the top level ROSE is
X.25 PLP.
So this zero-length filtering is invalid.
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: clean up
Create a sub directory in include/trace called events to keep the
trace point headers in their own separate directory. Only headers that
declare trace points should be defined in this directory.
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>