DibAcquireLock() is implemented as mutex_lock_interruptible()
but the driver does not handle unsuccessful locking.
As a result it may lead to unlock of an unheld mutex.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several error paths, where &state->platform.risc.mem_mbx_lock
is not unlocked. The patch fixes it.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch add CI support to az6007 driver.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In cx231xx_v4l2_close() there are two calls to
cx231xx_release_resources(dev) followed by kfree(dev). That is a
problem since cx231xx_release_resources() already kfree()'s its
argument, so we end up doing a double free.
Easily resolved by just removing the redundant kfree() calls after the
calls to cx231xx_release_resources().
I also changed the 'dev = NULL' assignments (which are rather
pointless since 'dev' is about to go out of scope), to 'fh->dev = NULL'
since it looks to me that that is what was actually intended.
And I removed the 'dev = NULL' assignment at the end of
cx231xx_release_resources() since it is pointless.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current delay of 30uS is too short to recover any carrier.
In the lmedm04 driver delays were added to overcome carrier lock
problems. The typical delay was 30mS (2 x 15ms register write
0x2c and read 0x24).
Other drivers that use STV0288 don't appear to have any delay are
likely to have also suffered this problem.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's no known problem here, but this is one of only two non-arch files
in the kernel which use asm/atomic.h instead of linux/atomic.h.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the PROBE_DEF quirk. Add a corresponding entry in
the device IDs list.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Userptr can be very useful if a UVC camera is requested to use video
buffers allocated by another processing device. So that buffers don't
need to be copied.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support 32-bit/64-bit compatibility for the the UVCIOC_ ioctls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-EINVAL is the wrong error code in that case, replace it with -ENOTTY.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Drivers implementing custom ioctls need to handle 32-bit/64-bit
compatibility themselves. Provide them with a way to do so.
To avoid circular module dependencies, merge the v4l2-compat-ioctl32
module into videodev. There is no point in keeping them separate, as the
v4l2_compat_ioctl32() function is required by videodev if CONFIG_COMPAT
is set anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* tag 'v3.3': (1646 commits)
Linux 3.3
Don't limit non-nested epoll paths
netfilter: ctnetlink: fix race between delete and timeout expiration
ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
nilfs2: clamp ns_r_segments_percentage to [1, 99]
afs: Remote abort can cause BUG in rxrpc code
afs: Read of file returns EBADMSG
C6X: remove dead code from entry.S
wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
net/hyperv: fix erroneous NETDEV_TX_BUSY use
net/usbnet: reserve headroom on rx skbs
bnx2x: fix memory leak in bnx2x_init_firmware()
bnx2x: fix a crash on corrupt firmware file
sch_sfq: revert dont put new flow at the end of flows
ipv6: fix icmp6_dst_alloc()
MAINTAINERS: Add Serge as maintainer of capabilities
drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
MAINTAINERS: add entry for exynos mipi display drivers
MAINTAINERS: fix link to Gustavo Padovans tree
...
WARNING: drivers/media/radio/built-in.o(.data+0x284): Section mismatch in reference from the variable fmr2_driver to the function .init.text:fmr2_probe()
The variable fmr2_driver references
the function __init fmr2_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
WARNING: drivers/media/built-in.o(.data+0x48200): Section mismatch in reference from the variable fmr2_driver to the function .init.text:fmr2_probe()
The variable fmr2_driver references
the function __init fmr2_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This card is based on the tea575x receiver. Use the tea575x-tuner framework
instead of reinventing the wheel.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tea575x-tuner module has been updated to use the latest V4L2 framework
functionality. This also required changes in the drivers that rely on it.
The tea575x changes are:
- The drivers must provide a v4l2_device struct to the tea module.
- The radio_nr module parameter must be part of the actual radio driver,
and not of the tea module.
- Changed the frequency range to the normal 76-108 MHz range instead of
50-150.
- Add hardware frequency seek support.
- Fix broken rxsubchans/audmode handling.
- The application can now select between stereo and mono.
- Support polling for control events.
- Add V4L2 priority handling.
And radio-sf16fmr2.c now uses the isa bus kernel framework.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Thanks-to: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When reading IF_AGC_GAIN register a wrong value for the base address
register was used (STB0899_DEMOD instead of STB0899_S2DEMOD). That
lead to a wrong signal strength value on DVB-S2 transponders.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In stb0899_read_status the FE_HAS_SIGNAL flag was not set in case of a
successful carrier lock. This change fixes that.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Acked-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit b2a29b578d sets accidentally
supported delivery systems as DVB-T/T2 whilst it should be
DVB-S/S2. Due to that frontend cannot be used at all.
Reported-by: Jiřà Zelenka <klacek@bubakov.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media fixes from Mauro Carvalho Chehab:
"For 4 fixes for 3.3 (all trivial):
- uvc video driver: fixes a division by zero;
- davinci: add module.h to fix compilation;
- smsusb: fix the delivery system setting;
- smsdvb: the get_frontend implementation there is broken.
The smsdvb patch has 127 lines, but it is trivial: instead of
returning a cache of the set_frontend (with is wrong, as it doesn't
have the updated values for the data, and the implementation there is
buggy), it copies the information of the detected DVB parameters from
the smsdvb private structures into the corresponding DVBv5 struct
fields."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] smsdvb: fix get_frontend
[media] smsusb: fix the default delivery system setting
[media] media: davinci: added module.h to resolve unresolved macros
[media] [FOR,v3.3] uvcvideo: Avoid division by 0 in timestamp calculation
Besides sticks with the usb id 14AA:0160, there exists also some
with 14AA:0161 - this is the output in /var/log/messages:
usb 1-1: new high-speed USB device number 2 using ehci_hcd
usb 1-1: New USB device found, idVendor=14aa, idProduct=0161
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: Freecom DVB-T
usb 1-1: Manufacturer: Freecom DVB-T
usb 1-1: SerialNumber: 00000000000036742
The patch is based on the code at
http://git.linuxtv.org/anttip/media_tree.git/shortlog/refs/heads/realtek
Signed-off-by: Paolo Pantò <munix9@googlemail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the macro DMA_BIT_MASK instead of the constant 0xffffffff.
Signed-off-by: Santosh Nayak <santoshprasadnayak@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In the get_frontend function, an internal copy of the dtv_frontend_properties
struct (which is never initialized) is copied over the frontend property cache
data structure, resetting everything to 0.
In particular, the delivery system is reset to 0 (which is an invalid value)
so the driver stops working as soon as a DVBv3 application calls the
get_frontend function, giving this error:
dvb_frontend_ioctl_legacy: doesn't know how to handle a DVBv3 call to delivery
system 0
This patch eliminates the unused internal copy of the dtv_frontend_properties
struct, and gives a proper implementation of the get_frontend function.
The original author of the patch is Panagiotis Malakoudis, who also tested
this new version on Ubuntu 11.10 with the latest media_build tree installed.
The original patch has been used on MIPS set-top-boxes for over one year,
but it was never posted on the linux-media list.
I ported the code to the current media_build tree (converting it to use the
dtv_frontend_properties struct) and added basic support for ISDB-T (untested).
Signed-off-by: Panagiotis Malakoudis <malakudi@gmail.com>
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The raw Sony IR decoder decodes 15bit messages slightly incorrectly.
To decode the function number, it shifts the bits right by 7 so that the
function is in bits 7:1, masks with 0xFD (0b11111101), and does an 8 bit
reverse so it ends up in bits 6:0. The mask should be 0xFE to correspond
with bits 7:1 (0b11111110).
The old mask had the effect of dropping the MSB of the function number
from bit 6, and leaving the LSB of the device number in bit 7.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds GPIO based IR Receiver driver. It decodes signals using decoders
available in rc framework.
Signed-off-by: Ravi Kumar V <kumarrav@codeaurora.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reverse cx18-driver part of commit
90ab5ee941 and change
module_param_array() type from bool to int to fix
compiler warning:
In function ‘__check_radio’:
113:1: warning: return from incompatible pointer type [enabled by default]
At top level:
113:1: warning: initialization from incompatible pointer type [enabled by default]
113:1: warning: (near initialization for ‘__param_arr_radio.num’) [enabled by default]
v2: corrected version, don't change to module_param_named(), change
all to int/uint
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In driver ivtv, there is a mismatch between the type of the radio module
parameter and the storage variable, which leads to the following
warning:
CC [M] drivers/media/video/ivtv/ivtv-driver.o
drivers/media/video/ivtv/ivtv-driver.c: In function ‘__check_radio’:
drivers/media/video/ivtv/ivtv-driver.c:142: warning: return from incompatible pointer type
drivers/media/video/ivtv/ivtv-driver.c: At top level:
drivers/media/video/ivtv/ivtv-driver.c:142: warning: initialization from incompatible pointer type
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The code was unnecessarily complex, introducing a hdl_out handler that was
not needed. Instead just add the controls to the cxhdl.hdl handler directly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently v4l2_ctrl_add_handler adds only the controls that are owned
by the handler. This is wrong. Instead all controls, whether owned or
not, should be added.
This is also implied by the v4l2-controls.txt documentation and it is
clearly the right thing to do. The only reason this was never noticed
before is because we never did this. Only recent changes in ivtv made
this error visible because there a third handler layer was added (handler
A inherits from handler B which inherits from C, D and E). Without this
change handler A only sees the controls owned by handler B and the controls
from C, D and E are missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
CHECK drivers/media/video/videobuf-vmalloc.c
CC [M] drivers/media/video/videobuf-vmalloc.o
+cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
+cc1: warning: drivers/media/dvb/frontends: No such file or directory [enabled by default]
+cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
+cc1: warning: drivers/media/dvb/frontends: No such file or directory [enabled by default]
LD drivers/media/built-in.o
Some details could be found in [1] as well.
[1] http://comments.gmane.org/gmane.linux.kbuild.devel/7733
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I don't have this hardware and I don't know the subsystem very well. So
please review this patch carefully. The original code definitely looks
buggy though.
Sparse complains about some endian bugs where little endian bugs are
treated as cpu endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"f" wasn't checked consistently, so static checkers complain. This
function is always called with a valid "f" pointer, so I have removed
the check.
Also the indenting was messed up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dean Anderson <linux-dev@sensoray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Raw IR events are passed to the raw event thread through a kfifo. The
size of the event struct is 12 bytes, and space for 512 events is
reserved in the kfifo (6144 bytes), however this is rounded down to 4096
bytes (the next power of 2) by __kfifo_alloc().
4096 bytes is not divisible by 12 therefore if the fifo fills up a third
of a record will be written in the end of the kfifo by
ir_raw_event_store() because the recsize of the fifo is 0 (it doesn't
have records). When this is read by ir_raw_event_thread() a corrupted or
partial record will be read, and in the case of a partial record the
BUG_ON(retval != sizeof(ev)) gets hit too.
According to samples/kfifo/record-example.c struct kfifo_rec_ptr_1 can
handle records of a length between 0 and 255 bytes, so change struct
ir_raw_event_ctrl to use that instead of struct kfifo.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the attached video sensor cannot provide the
requested image size, try to use resizing engine
included in the eMMa-PrP IP.
This patch supports both averaging and bilinear
algorithms.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
csi clock frequency is already shown by:
dev_info(&pdev->dev, "MX2 Camera (CSI) driver probed, clock frequency: %ld\n",
clk_get_rate(pcdev->clk_csi));
,so no need to have the dev_dbg call to present the same information.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some elements of 'mx2_buffer' are grouped together in another
auxiliary structure. This way we don't need to have unused
'vb2_buffer' structures for both discard buffers.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If active_bufs() list is empty and no IRQ status bit is set
we are probably dealing with a share IRQ. Return IRQ_NONE in
this case.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't need to use spin_lock_irqsave() since there are not
any other IRQs that can race with this ISR.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The way discard buffer was previously handled lead
to possible races that made a buffer that was not
yet ready to be overwritten by new video data. This
is easily detected at 25fps just adding "#define DEBUG"
to enable the "memset" check and seeing how the image
is corrupted.
A new "discard" queue and two discard buffers have
been added to make them flow trough the pipeline
of queues and thus provide suitable event ordering.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add "start_stream" and "stop_stream" callback in order to enable
and disable the eMMa-PrP properly and save CPU usage avoiding
IRQs when the device is not streaming. This also makes the driver
return 0 as the sequence number of the first frame.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
[g.liakhovetski@gmx.de: remove the mx27_camera_emma() macro]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i.MX27 DMA support was introduced with the initial commit of this
driver and originally created by me. However, I never got this stable
due to the racy DMA engine and used the EMMA engine instead. As the DMA
support is most probably unused and broken in its current state, remove
it. EMMA becomes the only supported mode on i.MX27.
This also helps us get rid of another user of the legacy i.MX DMA
support and remove the dependency on ARCH_MX* macros as these are
scheduled for removal.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[g.liakhovetski@gmx.de: remove unused goto]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The error handling in lgdt3303_read_status() and lgdt330x_read_ucblocks()
doesn't work, because i2c_read_demod_bytes() returns a u8 and (err < 0)
is always false.
err = i2c_read_demod_bytes(state, 0x58, buf, 1);
if (err < 0)
return err;
Change the return type of i2c_read_demod_bytes() to int. Also change
the return value on error to -EIO to make (err < 0) work.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On MIPS/ARM set-top-boxes, as well as old x86 PCs, memory allocation failures
in the em28xx driver are common, due to memory fragmentation over time, that
makes impossible to allocate large chunks of coherent memory.
A typical system with 256/512 MB of RAM fails after just 1 day of uptime (see
the old thread for detailed reports and crashlogs).
In fact, the em28xx driver allocates memory for USB isoc transfers at runtime,
as opposite to the dvb-usb drivers that allocates the USB buffers when the
device is initialized, and frees them when the device is disconnected.
Moreover, in digital mode the USB isoc transfer buffers are freed, allocated
and cleared every time the user selects a new channel, wasting time and
resources.
This patch solves both problems by allocating DVB isoc transfer buffers in
em28xx_usb_probe(), and freeing them in em28xx_usb_disconnect().
In fact, the buffers size and number depend only on the max USB packet size
that is parsed from the USB descriptors in em28xx_usb_probe(), so it can
never change for a given device.
This approach makes no sense in analog mode (as the buffer size depends on
the alternate mode selected at runtime), the patch creates two separate sets
of buffers for digital and analog modes.
For digital-only devices, USB buffers are created when the device is probed
and freed when the device is disconnected.
For analog-only devices, nothing changes: isoc buffers are created at runtime.
For hybrid devices, two sets of buffers are maintained: the digital-mode
buffers are created when the device is probed, and freed when the device is
disconnected; analog-mode buffers are created/destroyed at runtime as before.
So, in analog mode, digital and analog buffers coexists at the same time: this
can be justified by the fact that digital mode is by far more commonly used
nowadays, so it makes sense to optimize the driver for this use case scenario.
The patch has been tested in the last few days on a x86 PC and a MIPS
set-top-box, with the PCTV 290e (digital only) and the Terratec Hybrid XS
(hybrid device). With the latter, I switched several times between analog and
digital mode (Kaffeine/TvTime) with no issue at all.
I unplugged/plugged the devices several times with no problem.
Also, after over 3 days of normal usage in the MPIS set-top-box, the PCTV 290e
was still up and running.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The signal strength value returned is not quite correct, it decreases
when I increase the gain of my antenna, and vice versa. It also
doesn't span over the whole 0x0000-0xffff range. Compute a value which
at least increases when signal strength increases, and spans the whole
allowed range.
In practice I get 67% with my antenna fully amplified and 51% with
no amplification. This is close enough to what I get on my other
DVB-T adapter with the same antenna.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Read signal strength using VAR_P_INBAND and apply FEC preferred values.
Note this does not work on IT9137 devices even with dvb-usb-it9135-01.fw
firmware.
Config read_sl allows switch between read signal strength and signal
level.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow PID 8192 to turn PID filter off in USB high speed.
The PID number is still written to the PID index and will only
turn on again if that index is set to 0.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some virtual I2C commands are missed along some PID filtering
commands resulting complete stall of driver.
Since dvb-usb cannot handle the -EAGAIN error and commands
generally should not be missed mutex_lock is used instead.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch converts the drivers in drivers/media/* to use the
module_i2_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Heungjun Kim <riverful.kim@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Andrew Chew <achew@nvidia.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: Johannes Obermaier <johannes.obermaier@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The exposure was not set when autogain was set.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The setexposure added in commit 590f216806 works only for the sensor hv7131r,
but it is called for all sensors when changing the autogain.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bridge register 11 reports the current transfer status.
This value is used to know about a possible overflow and to adjust
the transfer parameters (registers 07 and 08).
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As the bridge register 08 defines the JPEG compression quality,
it must be changed on JPEG quality change and also, the decompression
tables must be adjusted when the register varies.
[mchehab@redhat.com: replace a // comment by a /* */ one]
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The auto gain uses the knee algorithm.
Adding the setexposure control function forced to:
- rename of the previous function setexposure
- add a specific auto setting function
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The get_jcomp control is rarely used and its main information,
the JPEG quality, may be found in the images.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The JPEG header is always the same, so, it does not need to be rebuild
each time a new frame is received.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize the subdev name properly so it doesn't have an I2C
bus and slave address appended to it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize the subdev name properly so it doesn't have an I2C
bus and slave address appended to it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initialize the subdev name properly so it doesn't have an I2C
bus and slave address appended to it.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adapt to new controls (subsampling).
For encoding, the destination format now needs to be set to V4L2_PIX_FMT_JPEG
and the subsampling (4:2:2 or 4:2:0) needs to be set using the respective
control (V4L2_CID_JPEG_CHROMA_SUBSAMPLING). Required buffer size for
destination image during encoding is no longer deduced from the format (which
generally implied overestimation), but needs to be given from userspace in
sizeimage.
Not strictly related to the added controls, this patch also fixes setting the
subsampling of the destination image for decoding, depending on the destination
format.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some video devices need to use contiguous memory which is
not backed by pages as it happens with vmalloc. This patch
provides USERPTR handling for those devices.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The devm_* functions are used in the platform device probe() for data
that is freed on driver removal. The managed device layer takes care
of undoing actions taken in the probe callback() and freeing resources
on driver detach. This eliminates the need for manually releasing
resources and simplifies error handling.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for cropping and composition setup on the video capture
node through VIDIOC_S/G_SELECTION ioctls. S/G_CROP, CROPCAP ioctls
are still supported for applications since the core will translate
them to *_selection handler calls.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The devm_* functions are used in the platform device probe() for data
that is freed on driver removal. The managed device layer takes care
of undoing actions taken in the probe callback() and freeing resources
on driver detach. This eliminates the need for manually releasing
resources and simplifies error handling.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver used the regulator API so it should depend on REGULATOR.
[mchehab@redhat.com: break depends on on two lines, instead of using a \]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Il 29/02/2012 22:30, Geert Uytterhoeven ha scritto:
> http://kisskb.ellerman.id.au/kisskb/buildresult/5759200/ ERROR:
> "__udivdi3" [drivers/media/dvb/frontends/rtl2830.ko] undefined!
>
The following patch fixed the warning on my 32 bit system.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces VIDIOC_S/G_JPEGCOMP ioctl handlers with
V4L2_CID_JPEG_QUALITY control. Additionally it enables JPEG subsampling
and the restart interval configuration through V4L2_CID_JPEG_SUBSAMPLING
and V4L2_CID_JPEG_RESTART_INTERVAL controls. For the decoder video node
only V4L2_CID_JPEG_SUBSAMPLING is available as a read-only control.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is a prerequisite for per file handle control handlers.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two issues on the default delivery system setting for smsusb:
1) instead of filling the delivery system for the per-client
frontend.ops, it were changing the global structure;
2) The client->frontend.ops copy were keeping the previous value
of the template. So, the first time the device was inserted,
it was using the wrong value.
Reported-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 382d19f197, as the
changes in question are done in v4l tree differently.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The V4L2_CID_JPEG_CLASS control class is intended to expose various
adjustable parameters of JPEG encoders and decoders. Following controls
are defined:
- V4L2_CID_JPEG_CHROMA_SUBSAMPLING,
- V4L2_CID_JPEG_RESTART_INTERVAL,
- V4L2_CID_JPEG_COMPRESSION_QUALITY,
- V4L2_CID_JPEG_ACTIVE_MARKER.
This covers only a part of relevant standard specifications. More
controls should be added in future if required.
The purpose of V4L2_CID_JPEG_CLASS class is also to replace some
functionality covered by VIDIOC_S/G_JPEGCOMP ioctls, i.e. the JPEG
markers presence and compression quality control. The applications
and drivers should switch from the ioctl to control based API, as
described in the subsequent patches for the Media API DocBook.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hardware is not accessible when device is sleeping.
Preventing such IOCTLs when sleep should be job of DVB CORE...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* some style issues
* remove rtl2832u device IDs
* move USB IDs to correct place
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement I2C functionality according to real RTL2830 demod.
Do not send register page in first byte of each I2C write, instead
use logic to set page using own write when needed. Page register is
physical register 0 as generally used.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not return error for demod attach in case of mxl5005s tuner.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For now it supports only Realtek RTL2831U chip.
RTL2831U is integrated DVB USB interface and DVB-T demod.
DVB-T demod integrated to RTL2831U is Realtek RTL2830.
Supported tuners are QT1010, MT2060 and MXL5005S.
Signed-off-by: Antti Palosaari <crope@iki.fi>
[mchehab@redhat.com: fix a small typo]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding support for using MHL (SiI9234 or other) chip if its configuration was
passed to HDMI by platfrom data.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Moving configuration of s5p-hdmi peripherals from driver data to
platfrom data.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
SiI9234 is a converter of HDMI signal into MHL. The chip is present on some
boards from Samsung S5P family. The chip's configuration procedure is based on
MHD_SiI9234 driver created by doonsoo45.kim.
The driver is using:
- i2c framework
- v4l2 framework
- runtime PM
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 99ac541254 removed
the function mt2063_setTune() from mt2063.c. Remove it
also from the header file.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Included module.h explicitly to resolve the macros THIS_MODULE and
MODULE_LICENSE. This avoids compilations errors as those defines were not
declared.
Signed-off-by: Henrique Camargo <henrique@henriquecamargo.com>
Signed-off-by: Diogo Luvizon <diogoluvizon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i.MX2x SoCs have a PrP which is capable of resizing and format
conversion of video frames. This driver provides support for
resizing and format conversion from YUYV to YUV420.
This operation is of the utmost importance since some of these
SoCs like i.MX27 include an H.264 video codec which only
accepts YUV420 as input.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use system timestamps if the timestamp can't be computed from the data
sent by the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] hdpvr: update picture controls to support firmware versions > 0.15
[media] wl128x: fix build errors when GPIOLIB is not enabled
[media] hdpvr: fix race conditon during start of streaming
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
[media] imon: don't wedge hardware after early callbacks
Correctly sets the max/min/default values for the hdpvr picture
controls. The reason the current values didn't cause a problem until now
is because any firmware <= 0.15 didn't support them. The latest firmware
releases properly support picture controls and the values in the patch
are derived from the windows driver using SniffUSB2.0.
Thanks to Devin Heitmueller for helping me.
Signed-off-by: Taylor Ralph <tralph@mythtv.org>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix wl128x Kconfig to depend on GPIOLIB since TI_ST also
depends on GPIOLIB.
(.text+0xe6d60): undefined reference to `st_register'
(.text+0xe7016): undefined reference to `st_unregister'
(.text+0xe70ce): undefined reference to `st_unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Manjunatha Halli <manjunatha_halli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Correctly sets the max/min/default values for the hdpvr picture
controls. The reason the current values didn't cause a problem until now
is because any firmware <= 0.15 didn't support them. The latest firmware
releases properly support picture controls and the values in the patch
are derived from the windows driver using SniffUSB2.0.
Thanks to Devin Heitmueller for helping me.
Signed-off-by: Taylor Ralph <tralph@mythtv.org>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix wl128x Kconfig to depend on GPIOLIB since TI_ST also
depends on GPIOLIB.
(.text+0xe6d60): undefined reference to `st_register'
(.text+0xe7016): undefined reference to `st_unregister'
(.text+0xe70ce): undefined reference to `st_unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Manjunatha Halli <manjunatha_halli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Specify chip revision at attach time rather than a firmware image.
This is a better way to ensure that the correct firmware is loaded
for the correct revision of the chip.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
convert the firmware configuration attach-time parameter from
a pointer to an integer so as to remove the static dependency
created by the previous changesets.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
newer versions of the xc5000 silicon require newer firmware
while remaining 100% driver compatible. original versions
of the xc5000a continue to use the same firmware.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Problems with the PID setting stalling demux on applications like VDR and MythTV.
The PID filter is now defaulted to OFF.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 7e07222 breaks DVBFE_ALGO_HW tuning after a retune is requested,
which causes bad tuning on my TBS 6920.
[ 0.769091] pci 0000:06:00.0: [14f1:8852] type 0 class 0x000400
[ 19.733530] CORE cx23885[0]: subsystem: 6920:8888, board: TurboSight TBS 6920 [card=14,autodetected]
[ 762.824912] cx24116_load_firmware: FW version 1.23.86.1
7e0722215a [media] dvb-core: Don't pass DVBv3 parameters on tune() fops
Although re_tune is set to true when FESTATE_RETUNE occurs, it is never
set back to false which the old code used to do when !FESTATE_RETUNE.
This patch sets re_tune to false if !(state & FESTATE_RETUNE).
$ szap-s2 -a 2 "Channel 5"
reading channels from file '/home/simon/.szap/channels.conf'
zapping to 247 'Channel 5':
delivery DVB-S, modulation QPSK
sat 0, frequency 10964 MHz H, symbolrate 22000000, coderate 5/6, rolloff 0.35
vpid 0x092a, apid 0x092b, sid 0x092d
using '/dev/dvb/adapter2/frontend0' and '/dev/dvb/adapter2/demux0'
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eb33 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cf40 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cec0 | snr eccd | ber 00000000 | unc 00000000 | FE_HAS_LOCK
status 1f | signal cec0 | snr 0000 | ber 00000000 | unc 00000000 | FE_HAS_LOCK
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with v4l2-compliance, but not with actual hardware. Contact the
linux-media mailinglist if you have this card!
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested with actual hardware (up to two cards) and the Keene USB FM Transmitter.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Alexey Khoroshilov