Change to using platform id table to match either of the two supported
platform device names in the driver. This simplifies the driver init and
exit code
Note, log messages will now be prefixed with 's3c-i2c' instead of the
driver name, so output will be of the form of:
s3c-i2c s3c2440-i2c.0: slave address 0x10
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Use longer noise filter period for fast and standard mode. Based on an
earlier patch by Eero Nurkkala.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fix scll/sclh calculations for HS and fast modes. Currently the driver
uses equal (roughly) low/high times which will result in too short
low time.
OMAP3430 TRM gives the following equations:
F/S: tLow = (scll + 7) * internal_clk
tHigh = (sclh + 5) * internal_clk
HS: tLow = (scll + 7) * fclk
tHigh = (sclh + 5) * fclk
Furthermore, the I2C specification sets the following minimum values
for HS tLow/tHigh for capacitive bus loads 100 pF (maximum speed 3400)
and 400 pF (maximum speed 1700):
speed tLow tHigh
3400 160 ns 60 ns
1700 320 ns 120 ns
and for F/S:
speed tLow tHigh
400 1300 ns 600 ns
100 4700 ns 4000 ns
By using duty cycles 33/66 (HS, F) and 50/50 (S) we stay above these
minimum values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Some drivers need i2c_smbus_read_i2c_block_data() functionality, so add
support for it to the Blackfin I2C bus driver.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
[ben-linux@fluff.org: shortened subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
We have a custom BF537 board with an I2C RTC (MAX DS3231) running
uclinux 2007R1 for some time. Recently during migration to 2008R1.5-RC3
we losted access to the RTC. The RTC driver calls 'i2c_transfer()' which
in turns calls 'bfin_twi_master_xfer()' in i2c-bfin-twi.c.
Compared with 2007R1, it looks like the 2008R1.5 version of i2c-bin-twi.c
has a new mode 'TWI_I2C-MODE_REPEAT' which corresponds to the Repeat Start
Condition described in the HRM. However, according to the HRM, at XMIT or
RECV interrupt and when the data count is 0, not only is the RESTART bit
supposed to be set, but MDIR must also be set if the next operation is a
receive sequence, and cleared if not. Currently there is no code that looks
at the I2C_M_RD bit in the flag from the next cur_msg and set/clear the MDIR
flag accordingly at the same time that the RSTART bit is set. Instead, MDIR
is set or cleared (by OR'ing with 0?) after the RESTART bit has been cleared
during handling of MCOMP interrupt.
It appears that this is causing our failure with reading the RTC, as a
quick patch to set/clear MDIR when RESTART is set seem to solve our problem.
Signed-off-by: Frank Shew <fshew@geometrics.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Avoid rewrite TWI MASTER_CTL reg when issue next message
In i2c repeat transfer mode, byte count of next message should be filled
into part of the TWI MASTER_CTL reg when interrupt MCOMP of last
message transfer is triggered. But, other bits in this reg should
not be touched.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shorted subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Make sure we don't end up with an invalid CLKDIV=0 in case someone
specifies 20kHz SCL or less (5 * 1024 / 20 = 0x100).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[ben-linux@fluff.org: shortened subject line]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: (30 commits)
[S390] wire up sys_perf_counter_open
[S390] wire up sys_rt_tgsigqueueinfo
[S390] ftrace: add system call tracer support
[S390] ftrace: add function graph tracer support
[S390] ftrace: add function trace mcount test support
[S390] ftrace: add dynamic ftrace support
[S390] kprobes: use probe_kernel_write
[S390] maccess: arch specific probe_kernel_write() implementation
[S390] maccess: add weak attribute to probe_kernel_write
[S390] profile_tick called twice
[S390] dasd: forward internal errors to dasd_sleep_on caller
[S390] dasd: sync after async probe
[S390] dasd: check_characteristics cleanup
[S390] dasd: no High Performance FICON in 31-bit mode
[S390] dcssblk: revert devt conversion
[S390] qdio: fix access beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
[S390] vmalloc: add vmalloc kernel parameter support
[S390] uaccess: use might_fault() instead of might_sleep()
[S390] 3270: lock dependency fixes
[S390] 3270: do not register with tty_register_device
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (50 commits)
drm: include kernel list header file in hashtab header
drm: Export hash table functionality.
drm: Split out the mm declarations in a separate header. Add atomic operations.
drm/radeon: add support for RV790.
drm/radeon: add rv740 drm support.
drm_calloc_large: check right size, check integer overflow, use GFP_ZERO
drm: Eliminate magic I2C frobbing when reading EDID
drm/i915: duplicate desired mode for use by fbcon.
drm/via: vfree() no need checking before calling it
drm: Replace DRM_DEBUG with DRM_DEBUG_DRIVER in i915 driver
drm: Replace DRM_DEBUG with DRM_DEBUG_MODE in drm_mode
drm/i915: Replace DRM_DEBUG with DRM_DEBUG_KMS in intel_sdvo
drm/i915: replace DRM_DEBUG with DRM_DEBUG_KMS in intel_lvds
drm: add separate drm debugging levels
radeon: remove _DRM_DRIVER from the preadded sarea map
drm: don't associate _DRM_DRIVER maps with a master
drm: simplify kcalloc() call to kzalloc().
intelfb: fix spelling of "CLOCK"
drm: fix LOCK_TEST_WITH_RETURN macro
drm/i915: Hook connector to encoder during load detection (fixes tv/vga detect)
...
* 'for-linus' of git://linux-arm.org/linux-2.6:
kmemleak: Add more info to the MAINTAINERS entry
kmemleak: Remove the kmemleak.h include in drivers/char/vt.c
This patch reworks the platform driver code for legacy
suspend and resume to avoid installing callbacks in
struct device_driver. A warning is also added telling
users to update the platform driver to use dev_pm_ops.
The functions platform_legacy_suspend()/resume() directly
call suspend and resume callbacks in struct platform_driver
instead of wrapping things in platform_drv_suspend()/resume().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch removes the legacy callbacks ->suspend() and
->resume() from struct device_type. These callbacks seem
unused, and new code should instead make use of struct
dev_pm_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove the ->suspend_late() and ->resume_early() callbacks
from struct bus_type V2. These callbacks are legacy stuff
at this point and since there seem to be no in-tree users
we may as well remove them. New users should use dev_pm_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1241) renames a bunch of functions in the PM core.
Rather than go through a boring list of name changes, suffice it to
say that in the end we have a bunch of pairs of functions:
device_resume_noirq dpm_resume_noirq
device_resume dpm_resume
device_complete dpm_complete
device_suspend_noirq dpm_suspend_noirq
device_suspend dpm_suspend
device_prepare dpm_prepare
in which device_X does the X operation on a single device and dpm_X
invokes device_X for all devices in the dpm_list.
In addition, the old dpm_power_up and device_resume_noirq have been
combined into a single function (dpm_resume_noirq).
Lastly, dpm_suspend_start and dpm_resume_end are the renamed versions
of the former top-level device_suspend and device_resume routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Rename the functions performing "_noirq" dev_pm_ops
operations from device_power_down() and device_power_up()
to device_suspend_noirq() and device_resume_noirq().
The new function names are chosen to show that the functions
are responsible for calling the _noirq() versions to finalize
the suspend/resume operation. The current function names do
not perform power down/up anymore so the names may be misleading.
Global function renames:
- device_power_down() -> device_suspend_noirq()
- device_power_up() -> device_resume_noirq()
Static function renames:
- suspend_device_noirq() -> __device_suspend_noirq()
- resume_device_noirq() -> __device_resume_noirq()
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Len Brown <lenb@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Sysdevs have to be suspended and resumed with interrupts disabled and
things usually break in a way that's difficult to debug if one of
sysdev drivers enables interrupts by mistake during suspend or
resume. Add extra checks that will generate warnings in such cases.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (154 commits)
[SCSI] osd: Remove out-of-tree left overs
[SCSI] libosd: Use REQ_QUIET requests.
[SCSI] osduld: use filp_open() when looking up an osd-device
[SCSI] libosd: Define an osd_dev wrapper to retrieve the request_queue
[SCSI] libosd: osd_req_{read,write} takes a length parameter
[SCSI] libosd: Let _osd_req_finalize_data_integrity receive number of out_bytes
[SCSI] libosd: osd_req_{read,write}_kern new API
[SCSI] libosd: Better printout of OSD target system information
[SCSI] libosd: OSD2r05: Attribute definitions
[SCSI] libosd: OSD2r05: Additional command enums
[SCSI] mpt fusion: fix up doc book comments
[SCSI] mpt fusion: Added support for Broadcast primitives Event handling
[SCSI] mpt fusion: Queue full event handling
[SCSI] mpt fusion: RAID device handling and Dual port Raid support is added
[SCSI] mpt fusion: Put IOC into ready state if it not already in ready state
[SCSI] mpt fusion: Code Cleanup patch
[SCSI] mpt fusion: Rescan SAS topology added
[SCSI] mpt fusion: SAS topology scan changes, expander events
[SCSI] mpt fusion: Firmware event implementation using seperate WorkQueue
[SCSI] mpt fusion: rewrite of ioctl_cmds internal generated function
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest: (31 commits)
lguest: add support for indirect ring entries
lguest: suppress notifications in example Launcher
lguest: try to batch interrupts on network receive
lguest: avoid sending interrupts to Guest when no activity occurs.
lguest: implement deferred interrupts in example Launcher
lguest: remove obsolete LHREQ_BREAK call
lguest: have example Launcher service all devices in separate threads
lguest: use eventfds for device notification
eventfd: export eventfd_signal and eventfd_fget for lguest
lguest: allow any process to send interrupts
lguest: PAE fixes
lguest: PAE support
lguest: Add support for kvm_hypercall4()
lguest: replace hypercall name LHCALL_SET_PMD with LHCALL_SET_PGD
lguest: use native_set_* macros, which properly handle 64-bit entries when PAE is activated
lguest: map switcher with executable page table entries
lguest: fix writev returning short on console output
lguest: clean up length-used value in example launcher
lguest: Segment selectors are 16-bit long. Fix lg_cpu.ss1 definition.
lguest: beyond ARRAY_SIZE of cpu->arch.gdt
...
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-virtio:
virtio: enhance id_matching for virtio drivers
virtio: fix id_matching for virtio drivers
virtio: handle short buffers in virtio_rng.
virtio_blk: add missing __dev{init,exit} markings
virtio: indirect ring entries (VIRTIO_RING_F_INDIRECT_DESC)
virtio: teach virtio_has_feature() about transport features
virtio: expose features in sysfs
virtio_pci: optional MSI-X support
virtio_pci: split up vp_interrupt
virtio: find_vqs/del_vqs virtio operations
virtio: add names to virtqueue struct, mapping from devices to queues.
virtio: meet virtio spec by finalizing features before using device
virtio: fix obsolete documentation on probe function
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-module-and-param:
module: cleanup FIXME comments about trimming exception table entries.
module: trim exception table on init free.
module: merge module_alloc() finally
uml module: fix uml build process due to this merge
x86 module: merge the rest functions with macros
x86 module: merge the same functions in module_32.c and module_64.c
uvesafb: improve parameter handling.
module_param: allow 'bool' module_params to be bool, not just int.
module_param: add __same_type convenience wrapper for __builtin_types_compatible_p
module_param: split perm field into flags and perm
module_param: invbool should take a 'bool', not an 'int'
cyber2000fb.c: use proper method for stopping unload if CONFIG_ARCH_SHARK
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (29 commits)
ide: re-implement ide_pci_init_one() on top of ide_pci_init_two()
ide: unexport ide_find_dma_mode()
ide: fix PowerMac bootup oops
ide: skip probe if there are no devices on the port (v2)
sl82c105: add printk() logging facility
ide-tape: fix proc warning
ide: add IDE_DFLAG_NIEN_QUIRK device flag
ide: respect quirk_drives[] list on all controllers
hpt366: enable all quirks for devices on quirk_drives[] list
hpt366: sync quirk_drives[] list with pdc202xx_{new,old}.c
ide: remove superfluous SELECT_MASK() call from do_rw_taskfile()
ide: remove superfluous SELECT_MASK() call from ide_driveid_update()
icside: remove superfluous ->maskproc method
ide-tape: fix IDE_AFLAG_* atomic accesses
ide-tape: change IDE_AFLAG_IGNORE_DSC non-atomically
pdc202xx_old: kill resetproc() method
pdc202xx_old: don't call pdc202xx_reset() on IRQ timeout
pdc202xx_old: use ide_dma_test_irq()
ide: preserve Host Protected Area by default (v2)
ide-gd: implement block device ->set_capacity method (v2)
...
This driver is originally written by Lennert, modified by Green to be
feature complete, and ported by Jun Nie and Kevin Liu for pxa168/910
processors.
The patch adds support for the on-chip LCD display controller, it
currently supports the base (graphics) layer only.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Green Wan <gwan@marvell.com>
Cc: Peter Liao <pliao@marvell.com>
Signed-off-by: Jun Nie <njun@marvell.com>
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Trivial patch which adds the __init and __exit macros to the module_init /
module_exit functions from drivers/pci/hotplug/sgi_hotplug.c
linux version 2.6.30-rc8
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
.ko is normally not included in Kconfig help, make it consistent.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The real 'armflash' map driver is selected by CONFIG_MTD_ARM_INTEGRATOR
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
drivers/message/fusion/mptsas.c
fixed up conflict between req->data_len accessors and mptsas driver updates.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
We no longer need an efficient mechanism to force the Guest back into
host userspace, as each device is serviced without bothering the main
Guest process (aka. the Launcher).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently, when a Guest wants to perform I/O it calls LHCALL_NOTIFY with
an address: the main Launcher process returns with this address, and figures
out what device to run.
A far nicer model is to let processes bind an eventfd to an address: if we
find one, we simply signal the eventfd.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Davide Libenzi <davidel@xmailserver.org>
We currently only allow the Launcher process to send interrupts, but it
as we already send interrupts from the hrtimer, it's a simple matter of
extracting that code into a common set_interrupt routine.
As we switch to a thread per virtqueue, this avoids a bottleneck through the
main Launcher process.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1) j wasn't initialized in setup_pagetables, so they weren't set up for me
causing immediate guest crashes.
2) gpte_addr should not re-read the pmd from the Guest. Especially
not BUG_ON() based on the value. If we ever supported SMP guests,
they could trigger that. And the Launcher could also trigger it
(tho currently root-only).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This version requires that host and guest have the same PAE status.
NX cap is not offered to the guest, yet.
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
replace LHCALL_SET_PMD with LHCALL_SET_PGD hypercall name
(That's really what it is, and the confusion gets worse with PAE support)
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Jeremy Fitzhardinge <jeremy@goop.org>
Some cleanups and replace direct assignment with native_set_* macros which properly handle 64-bit entries when PAE is activated
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If GDT_ENTRIES were every > 256, this could become a problem.
Signed-off-by: Matias Zabaljauregui <zabaljauregui at gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
lguest never checked for pending interrupts when enabling interrupts, and
things still worked. However, it makes a significant difference to TCP
performance, so it's time we fixed it by introducing a pending_irq flag
and checking it on irq_restore and irq_enable.
These two routines are now too big to patch into the 8/10 bytes
patch space, so we drop that code.
Note: The high latency on interrupt delivery had a very curious
effect: once everything else was optimized, networking without GSO was
faster than networking with GSO, since more interrupts were sent and
hence a greater chance of one getting through to the Guest!
Note2: (Almost) Closing the same loophole for iret doesn't have any
measurable effect, so I'm leaving that patch for the moment.
Before:
1GB tcpblast Guest->Host: 30.7 seconds
1GB tcpblast Guest->Host (no GSO): 76.0 seconds
After:
1GB tcpblast Guest->Host: 6.8 seconds
1GB tcpblast Guest->Host (no GSO): 27.8 seconds
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When the Guest does the LHCALL_HALT hypercall, we go to sleep, expecting
that a timer or the Waker will wake_up_process() us.
But we do it in a stupid way, leaving a classic missing wakeup race.
So split maybe_do_interrupt() into interrupt_pending() and
try_deliver_interrupt(), and check maybe_do_interrupt() and the
"break_out" flag before calling schedule.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The Launcher could be inside the Guest on another CPU; wake_up_process
will do nothing because it is "running". kick_process will knock it
back into our kernel in this case, otherwise we'll miss it until the
next guest exit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This patch allows a virtio driver to use VIRTIO_DEV_ANY_ID for the
device id. This will be used by a test module that can be bound to
any virtio device.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This bug never appeared, since all current virtio drivers use
VIRTIO_DEV_ANY_ID for the vendor field. If a real vendor would be used,
the check in virtio_id_match is wrong - it returns 0 if
id->vendor == dev->id.vendor.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If the device fills less than 4 bytes of our random buffer, we'll
BUG_ON. It's nicer to handle the case where it partially fills the
buffer (the protocol doesn't explicitly bad that).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The remove member of the virtio_driver structure uses __devexit_p(), so
the remove function itself should be marked with __devexit. And where
there be __devexit on the remove, so is there __devinit on the probe.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Add a new feature flag for indirect ring entries. These are ring
entries which point to a table of buffer descriptors.
The idea here is to increase the ring capacity by allowing a larger
effective ring size whereby the ring size dictates the number of
requests that may be outstanding, rather than the size of those
requests.
This should be most effective in the case of block I/O where we can
potentially benefit by concurrently dispatching a large number of
large requests. Even in the simple case of single segment block
requests, this results in a threefold increase in ring capacity.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This implements optional MSI-X support in virtio_pci.
MSI-X is used whenever the host supports at least 2 MSI-X
vectors: 1 for configuration changes and 1 for virtqueues.
Per-virtqueue vectors are allocated if enough vectors
available.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ whitespace, style)
This reorganizes virtio-pci code in vp_interrupt slightly, so that
it's easier to add per-vq MSI support on top.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This replaces find_vq/del_vq with find_vqs/del_vqs virtio operations,
and updates all drivers. This is needed for MSI support, because MSI
needs to know the total number of vectors upfront.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (+ lguest/9p compile fixes)
Add a linked list of all virtqueues for a virtio device: this helps for
debugging and is also needed for upcoming interface change.
Also, add a "name" field for clearer debug messages.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Virtio devices are supposed to negotiate features before they start using
the device, but the current code doesn't do this. This is because the
driver's probe() function invariably has to add buffers to a virtqueue,
or probe the disk (virtio_blk).
This currently doesn't matter since no existing backend is strict about
the feature negotiation. But it's possible to imagine a future feature
which completely changes how a device operates: in this case, we'd need
to acknowledge it before using the device.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
1) Now module_param(..., invbool, ...) requires a bool, and similarly
module_param(..., bool, ...) allows it, change pmi_setpal to a bool.
2) #define param_get_scroll to NULL, since it can never be called (perm
argument to module_param_named is 0).
3) Return -EINVAL from param_set_scroll if the value is bad, so it's
reported.
Note that I don't think the old fb_get_options() is required for new
drivers: the parameters automatically work as uvesafb.XXX=... anyway.
Acked-by: Michał Januszewski <spock@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
It takes an 'int' for historical reasons, and there are only two
users: simply switch it over to bool.
The other user (uvesafb.c) will get a (harmless-on-x86) warning until
the next patch is applied.
Cc: Brad Douglas <brad@neruo.com>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Russell explains the __module_get():
> cyber2000fb.c does it in its module initialization function
> to prevent the module (when built for Shark) from being unloaded. It
> does this because it's from the days of 2.2 kernels and no one bothered
> writing the module unload support for Shark.
Since 2.4, the correct answer has been to not define an unload fn.
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: alex@shark-linux.de
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This file is no longer annotated for false positives but the kmemleak.h
include was still present.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Alan Cox <alan.cox@linux.intel.com>
Function graph tracer support for s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a DASD requests is started with dasd_sleep_on and fails, then the
calling function may need to know the reason for the failure.
In cases of hardware errors it can inspect the sense data in the irb,
but when the reason is internal (e.g. start_IO failed) then it needs
a meaningfull return code.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some functions called as a late_initcall depend on completely
initialized devices. Since commit
f3445a1a65 the dasd driver uses the
new async framework and relies on the fact that synchronization is
done in prepare_namespace which is called after the late_initcalls.
Fix this by calling async_synchronize_full at the end of the related
init functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix a broken memset (sizeof pointer vs sizeof the underlying
structure) by cleaning up the involved functions.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The High Performance FICON feature is not supported in 31-bit mode,
no matter what the various flags say. So we need to check for the
CONFIG_64BIT option as well.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
git commit f331c0296f changed users of
->first_minor to devt. This broke device handling in dcssblk, so that
no additional devices could be added after the first one.
This patch reverts the devt conversion to the previous ->first_minor
handling.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Do not go beyond ARRAY_SIZE of irq_ptr->{in,out}put_qs
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Lockdep found a problem with the lock order of the view lock and the
ccw device lock. raw3270_activate_view/raw3270_deactivate_view first
take the ccw device lock then call the activate/deactivate functions
of the view which take view lock. The update functions of the
con3270/tty3270 view will first take the view lock, then take the
ccw device lock. To fix this the activate/deactivate functions are
changed to avoid taking the view lock by moving the functions calls
that modify the 3270 output buffer to the update function which is
called by a timer.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The tty3270_notifier that calls tty_register_device / tty_unregister_device
is harmful in two ways:
1) the device node that is create is wrong because the minor numbers for
3270 tty start with 1 and tty_notifier passes the minor as index.
2) If 1) is corrected you'll get a warning:
WARNING: at fs/sysfs/dir.c:462 sysfs_add_one+0x4c/0x60()
sysfs: duplicate filename '227:1' can not be created
The 227:1 link is already created by raw3270_create_attributes to refer
to ../../class/tty/tty<devno>. There cannot be two links.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move qdio_perf_stat_inc to the header file so it can be inlined.
Remove unused qdio_perf_stat_dec.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The check for the device status in qdio_establish_handle_irq()
had dead code. Remove the unused code and simplify the error
handling.
Signed-off-by: Jan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some sanity checks in device_ops.c test the output of container_of
macros to be !NULL. Test the input parameters instead.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
All definition in cpu.h have to do with cputime accounting. Move
them to cputime.h and remove the header file.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
add exports so TTM module can use these functions.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
this is a TTM preparation patch, it rearranges the mm and
add operations needed to do mm operations in atomic context.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This code depends on the underlying I2C adapter using the bit-banging algo,
which may not be the case. If specific encoders require this mechanism, they
should build a custom I2C algo that implements this workaround, rather than
having it in the general path.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
vfree() does it's own NULL checking, no need for explicit check before
calling it.
Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace the DRM_DEBUG with the DRM_DEBUG_DRIVER to print the debug info
in i915 driver.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Replace the DRM_DEBUG with DRM_DEBUG_MODE macro to print the info in drm_mode.
airlied:- fixed up to remove a conflicting #define
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The only user of the i_cindex element in the inode structure is used
is by the firewire drivers. As part of an attempt to slim down the
inode structure to save memory --- since a typical Linux system will
have hundreds of thousands if not millions of inodes cached, a
reduction in the size inode has high leverage.
The firewire driver does not need i_cindex in any fast path, so it's
simple enough to calculate when it is needed, instead of wasting space
in the inode structure.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: krh@redhat.com
Cc: stefanr@s5r6.in-berlin.de
Cc: linux-fsdevel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'for-linus' of git://linux-arm.org/linux-2.6:
kmemleak: Add the corresponding MAINTAINERS entry
kmemleak: Simple testing module for kmemleak
kmemleak: Enable the building of the memory leak detector
kmemleak: Remove some of the kmemleak false positives
kmemleak: Add modules support
kmemleak: Add kmemleak_alloc callback from alloc_large_system_hash
kmemleak: Add the vmalloc memory allocation/freeing hooks
kmemleak: Add the slub memory allocation/freeing hooks
kmemleak: Add the slob memory allocation/freeing hooks
kmemleak: Add the slab memory allocation/freeing hooks
kmemleak: Add documentation on the memory leak detector
kmemleak: Add the base support
Manual conflict resolution (with the slab/earlyboot changes) in:
drivers/char/vt.c
init/main.c
mm/slab.c
* 'perfcounters-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (574 commits)
perf_counter: Turn off by default
perf_counter: Add counter->id to the throttle event
perf_counter: Better align code
perf_counter: Rename L2 to LL cache
perf_counter: Standardize event names
perf_counter: Rename enums
perf_counter tools: Clean up u64 usage
perf_counter: Rename perf_counter_limit sysctl
perf_counter: More paranoia settings
perf_counter: powerpc: Implement generalized cache events for POWER processors
perf_counters: powerpc: Add support for POWER7 processors
perf_counter: Accurate period data
perf_counter: Introduce struct for sample data
perf_counter tools: Normalize data using per sample period data
perf_counter: Annotate exit ctx recursion
perf_counter tools: Propagate signals properly
perf_counter tools: Small frequency related fixes
perf_counter: More aggressive frequency adjustment
perf_counter/x86: Fix the model number of Intel Core2 processors
perf_counter, x86: Correct some event and umask values for Intel processors
...
* 'topic/slab/earlyboot' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
vgacon: use slab allocator instead of the bootmem allocator
irq: use kcalloc() instead of the bootmem allocator
sched: use slab in cpupri_init()
sched: use alloc_cpumask_var() instead of alloc_bootmem_cpumask_var()
memcg: don't use bootmem allocator in setup code
irq/cpumask: make memoryless node zero happy
x86: remove some alloc_bootmem_cpumask_var calling
vt: use kzalloc() instead of the bootmem allocator
sched: use kzalloc() instead of the bootmem allocator
init: introduce mm_init()
vmalloc: use kzalloc() instead of alloc_bootmem()
slab: setup allocators earlier in the boot sequence
bootmem: fix slab fallback on numa
bootmem: use slab if bootmem is no longer available
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] ata_piix: Enable parallel scan
sata_nv: use hardreset only for post-boot probing
[libata] ahci: Restore SB600 SATA controller 64 bit DMA
ata_piix: Remove stale comment
ata_piix: Turn on hotplugging support for older chips
ahci: misc cleanups for EM stuff
[libata] get rid of ATA_MAX_QUEUE loop in ata_qc_complete_multiple() v2
sata_sil: enable 32-bit PIO
sata_sx4: speed up ECC initialization
libata-sff: avoid byte swapping in ata_sff_data_xfer()
[libata] ahci: use less error-prone array initializers
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
* 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (28 commits)
ide-tape: fix debug call
alim15x3: Remove historical hacks, re-enable init_hwif for PowerPC
ide-dma: don't reset request fields on dma_timeout_retry()
ide: drop rq->data handling from ide_map_sg()
ide-atapi: kill unused fields and callbacks
ide-tape: simplify read/write functions
ide-tape: use byte size instead of sectors on rw issue functions
ide-tape: unify r/w init paths
ide-tape: kill idetape_bh
ide-tape: use standard data transfer mechanism
ide-tape: use single continuous buffer
ide-atapi,tape,floppy: allow ->pc_callback() to change rq->data_len
ide-tape,floppy: fix failed command completion after request sense
ide-pm: don't abuse rq->data
ide-cd,atapi: use bio for internal commands
ide-atapi: convert ide-{floppy,tape} to using preallocated sense buffer
ide-cd: convert to using generic sense request
ide: add helpers for preparing sense requests
ide-cd: don't abuse rq->buffer
ide-atapi: don't abuse rq->buffer
...
Slab is initialized before the console subsystem so use the slab allocator in
vgacon_scrollback_startup().
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Now that kmem_cache_init() happens before console_init(), we should use
kzalloc() and not the bootmem allocator.
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
