ADS7845 is a controller for 5-wire touch screens and somewhat
different from 7846. It requires three serial communications to
accomplish one complete conversion. Unlike 7846 it doesn't allow
Z1-/Z2- position measurement.
The patch extends the ads7846 driver to also support ads7845.
The packet struct is extended to contain needed command and
conversion buffers. ads7846_rx() and ads7846_rx_val() now
differentiate between 7845 and 7846 case. ads7846_probe() is
modified to setup ads7845 specific command and conversion
messages and to switch ads7845 into power-down mode, since
this is needed to be prepared to respond to pendown interrupts.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Suspending and resuming the device should be separate from enabling
and disabling it through sysfs attribute and thus should not alter
ac->disabled flag.
[michael.hennerich@analog.com: various fixups]
Tested-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some input events users such as Android require BTN_TOUCH events.
Implement EV_KEY/BTN_TOUCH and make sure that the release event
is not erroneous scheduled without a preceding valid touch.
Avoid duplicated BTN_TOUCH events, even though input core filters
them.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The ad7879 driver is using the old bus method of only supporting one
at a time (I2C or SPI). So refactor it like the other input drivers
that support multiple busses simultaneously.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We reuse the "i" variable later on so if we goto fail3 or fail4
then "i" will be set to the wrong thing and cause a crash.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
gpiolib now has debounce support added in .35, so let's make use of it.
This allows to use hardware GPIO debouncing on some platforms like OMAP.
In case gpiolib debounce setup fails for some GPIO, the driver will fall
back to timer based debouncing, which is what it used before.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The device is handled by usbtouchscreen driver.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the ET&T TC4UM 4-wire USB touchscreen
controller and tries to reuse the bits for TC5UH controller in kernel
already. Data interface is same.
Tested-by: Roger Pueyo Centelles <rogerpueyo@rogerpueyo.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On some platforms, for example with GPIO interrupts on mpc5121,
it is not possible to configure falling edge interrupts.
Specifying irq trigger type in platform data structure
allows using ads7846 driver on such platforms.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
select_keymap() calls copy_keymap() to allocate a memory for keymap.
This patch adds a missing kfree(keymap) in wb_module_init error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is a driver for the ADXL345/346 Three-Axis Digital Accelerometers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Chris Verges <chrisv@cyberswitching.com>
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A column or row configured as a GPI can be programmed to be part
of the key event table and therefore also capable of generating a
key event interrupt. A key event interrupt caused by a GPI follows
the same process flow as a key event interrupt caused by a key
press. GPIs configured as part of the key event table allow single
key switches and other GPI interrupts to be monitored. As part of
the event table, GPIs are represented by the decimal value 97 (0x61
or 1100001) through the decimal value 114 (0x72 or 1110010). See
table below for GPI event number assignments for rows and columns.
GPI Event Number Assignments for Rows
Row0 Row1 Row2 Row3 Row4 Row5 Row6 Row7
97 98 99 100 101 102 103 104
GPI Event Number Assignments for Cols
Col0 Col1 Col2 Col3 Col4 Col5 Col6 Col7 Col8 Col9
105 106 107 108 109 110 111 112 113 114
Signed-off-by: Xiaolong Chen <xiao-long.chen@motorola.com>
Signed-off-by: Yuanbo Ye <yuan-bo.ye@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
When the client buffer is very small and wraps around a lot, it may
well be that a write increases the head such that head == tail. If
this happens between the point where a poll is triggered and the
actual data is being read, there will be no data to read. This is
confusing to applications, which might end up closing the file.
This patch solves the problem by making sure the client buffer is
never empty after writing to it.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MT devices produce a lot of data. Tell the underlying input device
approximately how many events will be sent per synchronization, to allow
for better buffering. The number is a template based on continuously
reporting details for each finger on a single hand.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The MT devices produce a lot of data. Tell the underlying input device
approximately how many events will be sent per synchronization, to allow
for better buffering. The number is a template based on continuously
reporting details for each finger on a single hand.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some devices, in particular MT devices, produce a lot of data. This
may lead to overflowing of the event queues in evdev driver, which
by default are fairly small. Let the drivers hint the average number
of events per packet generated by the device, and use that information
when computing the buffer size evdev should use for the device.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allocate the event buffer dynamically, and prepare to compute the
buffer size in a separate function. This patch defines the size
computation to be identical to the current code, and does not contain
any logical changes.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Stanse found that tsc is dereferenced earlier than checked for being
NULL in tps6507x_ts_remove. Remove the test because there is no way
for tsc to be NULL there.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
wimax/i2400m: fix missing endian correction read in fw loader
net8139: fix a race at the end of NAPI
pktgen: Fix accuracy of inter-packet delay.
pkt_sched: gen_estimator: add a new lock
net: deliver skbs on inactive slaves to exact matches
ipv6: fix ICMP6_MIB_OUTERRORS
r8169: fix mdio_read and update mdio_write according to hw specs
gianfar: Revive the driver for eTSEC devices (disable timestamping)
caif: fix a couple range checks
phylib: Add support for the LXT973 phy.
net: Print num_rx_queues imbalance warning only when there are allocated queues
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: clear bridge resource range if BIOS assigned bad one
PCI: hotplug/cpqphp, fix NULL dereference
Revert "PCI: create function symlinks in /sys/bus/pci/slots/N/"
PCI: change resource collision messages from KERN_ERR to KERN_INFO
There are devices out there which are PCI Hot-plug controllers with
compaq PCI IDs, but are not bridges, hence have pdev->subordinate
NULL. But cpqphp expects the pointer to be non-NULL.
Add a check to the probe function to avoid oopses like:
BUG: unable to handle kernel NULL pointer dereference at 00000050
IP: [<f82e3c41>] cpqhpc_probe+0x951/0x1120 [cpqphp]
*pdpt = 0000000033779001 *pde = 0000000000000000
...
The device here was:
00:0b.0 PCI Hot-plug controller [0804]: Compaq Computer Corporation PCI Hotplug Controller [0e11:a0f7] (rev 11)
Subsystem: Compaq Computer Corporation Device [0e11:a2f8]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit 75568f8094.
Since they're just a convenience anyway, remove these symlinks since
they're causing duplicate filename errors in the wild.
Acked-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We can often deal with PCI resource issues by moving devices around. In
that case, there's no point in alarming the user with messages like these.
There are many bug reports where the message itself is the only problem,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/413419 .
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
i2400m_fw_hdr_check() was accessing hardware field
bcf_hdr->module_type (little endian 32) without converting to host
byte sex.
Reported-by: Данилин Михаил <mdanilin@nsg.net.ru>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid validate_cis failure on CIS override
pcmcia: dev_node removal bugfix
pcmcia: yenta_socket.c Remove extra #ifdef CONFIG_YENTA_TI
pcmcia: only keep saved I365_CSCINT flag if there is no PCI irq
fix a race at the end of NAPI complete processing, it had
better do __napi_complete() first before re-enable interrupt.
Signed-off-by:Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data in the cmd_block buffers may reach the main memory after the
writel() to the device ports. This patch introduces two calls to wmb()
to ensure the relative ordering.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Colin Tuckley <colin.tuckley@arm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
cb->atapi.cdb is an array of 16 u8 elements. The call too memset()
would set the first part of the sge array to zero as well. It's not
a packed struct.
This one has been around for five years. I found it with Smatch. I
think the reason no one has seen it before is because we normally call
sil24_fill_sg() and that overwrites sge with proper information?
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This one adds support of a combined irq source for the whole matrix keypad.
This can be useful if all rows and columns of the keypad are e.g. connected
to a GPIO expander, which only has one interrupt line for all events on
every single GPIO.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cc772ab7cd ("gianfar: Add
hardware RX timestamping support"), the driver no longer works on
at least MPC8313ERDB and MPC8568EMDS boards (and possibly much more
boards as well).
That's how MPC8313 Reference Manual describes RCTRL_TS_ENABLE bit:
Timestamp incoming packets as padding bytes. PAL field is set
to 8 if the PAL field is programmed to less than 8. Must be set
to zero if TMR_CTRL[TE]=0.
I see that the commit above sets this bit, but it doesn't handle
TMR_CTRL. Manfred probably had this bit set by the firmware for
his boards. But obviously this isn't true for all boards in the
wild.
Also, I recall that Freescale BSPs were explicitly disabling the
timestamping because of a performance drop.
For now, the best way to deal with this is just disable the
timestamping, and later we can discuss proper device tree bindings
and implement enabling this feature via some property.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a work around for Erratum 5, "3.3 V Fiber Speed
Selection." If the hardware wiring does not respect this erratum, then
fiber optic mode will not work properly.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
mac80211: fix deauth before assoc
iwlwifi: add missing rcu_read_lock
mac80211: fix function pointer check
wireless: remove my name from the maintainer list
ath5k: fix NULL pointer in antenna configuration
p54usb: Add device ID for Dell WLA3310 USB
wl1251: fix a memory leak in probe
ipmr: dont corrupt lists
8139too: fix buffer overrun in rtl8139_init_board
asix: check packet size against mtu+ETH_HLEN instead of ETH_FRAME_LEN
r8169: fix random mdio_write failures
ip6mr: fix a typo in ip6mr_for_each_table()
iwlwifi: move sysfs_create_group to post request firmware
iwlwifi: add name to Maintainers list
iwl3945: fix internal scan
iwl3945: enable stuck queue detection on 3945
ipv6: avoid high order allocations
ath5k: retain promiscuous setting
ath5k: depend on CONFIG_PM_SLEEP for suspend/resume functions
mac80211: process station blockack action frames from work
...
MSM7x30 isn't supported in this driver yet. If ones tried to compile it in
with MSM7x30 configure you get,
linux-2.6/drivers/mmc/host/msm_sdcc.c: In function 'msmsdcc_fifo_addr':
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: 'MSM_SDC1_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: (Each undeclared identifier is reported only once
linux-2.6/drivers/mmc/host/msm_sdcc.c:165: error: for each function it appears in.)
linux-2.6/drivers/mmc/host/msm_sdcc.c:167: error: 'MSM_SDC2_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:169: error: 'MSM_SDC3_PHYS' undeclared (first use in this function)
linux-2.6/drivers/mmc/host/msm_sdcc.c:171: error: 'MSM_SDC4_PHYS' undeclared (first use in this function)
So we add a Kconfig check to prevent this.
Signed-off-by: Daniel Walker <dwalker@codeaurora.org>
10, 233 is allocated officially to /dev/kmview which is shipping in
Ubuntu and Debian distributions. vhost_net seem to have borrowed it
without making a proper request and this causes regressions in the other
distributions.
vhost_net can use a dynamic minor so use that instead. Also update the
file with a comment to try and avoid future misunderstandings.
cc: stable@kernel.org
Signed-off-by: Alan Cox <device@lanana.org>
[ We should have caught this before 2.6.34 got released. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: core: check for 1394a compliant IRM, fix inaccessibility of Sony camcorder
This reverts commit cfecde435d, since it
seems to cause some systems to not come up with any video output at all
(or video that only comes on when X starts up).
Fixes bugzilla:
http://bugzilla.kernel.org/show_bug.cgi?id=16163
Reported-and-tested-by: David John <davidjon@xenontk.org>
Tested-by: Nick Bowler <nbowler@elliptictech.com>
Acked-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (23 commits)
drm/radeon: don't poll tv dac if crtc2 is in use.
drm/radeon: reset i2c valid to avoid incorrect tv-out polling.
drm/nv50: fix iommu errors caused by device reading from address 0
drm/nouveau: off by one in init_i2c_device_find()
nouveau: off by one in nv50_gpio_location()
drm/nouveau: completely fail init if we fail to map the PRAMIN BAR
drm/nouveau: match U/DP script against SOR link
drm/radeon/kms/pm: resurrect printing power states
drm/radeon/kms: add trivial debugging for voltage
drm/radeon/kms/r600+: use voltage from requested clock mode (v3)
drm/radeon/kms/pm: track current voltage (v2)
drm/radeon/kms/pm: Disable voltage adjust on RS780/RS880
drm/radeon/kms: fix typo in printing the HPD info
drm/radeon/kms/pm: add mid profile
drm/radeon/kms/pm: Misc fixes
drm/radeon/kms/combios: fix typo in voltage fix
drm/radeon/kms/evergreen: set accel_enabled
drm/vmwgfx: return -EFAULT for copy_to_user errors
drm/drm_crtc: return -EFAULT on copy_to_user errors
drm/fb: use printk to print out the switching to text mode error.
...
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] Update default configuration.
[S390] arch/s390/kvm: Use GFP_ATOMIC when a lock is held
[S390] kprobes: add parameter check to module_free()
[S390] appldata/extmem/kvm: add missing GFP_KERNEL flag
Anatolij Gustschin