These haven't seen much attention for too long but particularly important
enable RTC_CLASS and CONFIG_RTC_HCTOSYS so the wall clock time is set on
kernel startup.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the conversion of MIPS to RTC_LIB the old RTC driver CONFIG_RTC became
unselectable. Fix by setting up a platform device. Also enable
RTC_CLASS so system time gets set from RTC on kernel initialization.
[Ralf: Original patch by Tiejun; polished nice and shiny by me]
Signed-off-by: Tiejun Chen <tiejun.chen@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On a 64 bit kernel if an o32 syscall was made with a syscall number less
than 4000, we would read the function from outside of the bounds of the
syscall table. This led to non-deterministic behavior including system
crashes.
While we were at it we reworked the 32 bit version as well to use fewer
instructions. Both 32 and 64 bit versions are use the same code now.
Signed-off-by: Vlad Malov <Vlad.Malov@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Just found the merge issue in 442746989d
("powerpc/83xx: Add support for MCU microcontroller in .dts files"):
the commit adds the MCU controller node into the DMA node, which is
wrong because the MCU sits on the I2C bus. Fix this by moving the MCU
node into the I2C controller node.
The original patch[1] was OK though. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On PowerPC 4xx or other non cache-coherent platforms, we lost the
appropriate cache flushing in dma_map_sg() when merging the 32 and
64-bit DMA code (commit 4fc665b88a,
"powerpc: Merge 32 and 64-bit dma code"). This restores it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: MMU: avoid creation of unreachable pages in the shadow
KVM: ppc: stop leaking host memory on VM exit
KVM: MMU: fix sync of ptes addressed at owner pagetable
KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER
KVM: ia64: Fix incorrect kbuild CFLAGS override
KVM: VMX: Fix interrupt loss during race with NMI
KVM: s390: Fix problem state handling in guest sigp handler
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Update defconfigs for 2.6.28-rc7
macfb: Do not overflow fb_fix_screeninfo.id
This fixes the MN10300 kernel module linking to match the toolchain. RELA
relocs don't use the value at the location being relocated. This has been
working because the tools always leave the value at the target location
cleared.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id. We were writing that directly
into the HW register.
We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the error handling in sys_mmap2(). Currently, if the pgoff check
fails, fput() might have to be called (which it isn't), so do the pgoff
check first, before fget() is called.
Signed-off-by: David Howells <dhowells@redhat.com>
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spi master driver must have num_chipselect set to allow the bus to
initialise. Pass this through the platform data.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit e669dae614, since it
is incomplete, and clashes with fuller patches and the sparc 32/64
unification effort.
Requested-by: David Miller <davem@davemloft.net>
Acked-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
attr_smt_snooze_delay is only defined for CONFIG_PPC64, so protect the
attribute removal with the same condition. This fixes this build error
on 32-bit SMP configurations:
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c: In function ‘unregister_cpu_online’:
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: ‘attr_smt_snooze_delay’ undeclared (first use in this function)
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: (Each undeclared identifier is reported only once
/data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: for each function it appears in.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
* master.kernel.org:/home/rmk/linux-2.6-arm:
Allow architectures to override copy_user_highpage()
[ARM] pxa/palmtx: misc fixes to use generic GPIO API
ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling
[ARM] pxa/corgi: update default config to exclude tosa from being built
[ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data
ARM: OMAP: Typo fix for clock_allow_idle
ARM: OMAP: Remove broken LCD driver for SX1
[ARM] 5335/1: pxa25x_udc: Fix is_vbus_present to return 1 or 0
[ARM] pxa/MioA701: bluetooth resume fix
[ARM] pxa/MioA701: fix memory corruption.
It turns out that on Cell, on a kernel with CONFIG_VIRT_CPU_ACCOUNTING
= y, if a program sets the SO (summary overflow) bit in the XER and
then does a system call, the SO bit in CR0 will be set on return
regardless of whether the system call detected an error. Since CR0.SO
is used as the error indication from the system call, this means that
all system calls appear to fail.
The reason is that the workaround for the timebase bug on Cell uses a
compare instruction. With CONFIG_VIRT_CPU_ACCOUNTING = y, the
ACCOUNT_CPU_USER_ENTRY macro reads the timebase, so we end up doing a
compare instruction, which copies XER.SO to CR0.SO. Since we were
doing this in the system call entry patch after clearing CR0.SO but
before saving the CR, this meant that the saved CR image had CR0.SO
set if XER.SO was set on entry.
This fixes it by moving the clearing of CR0.SO to after the
ACCOUNT_CPU_USER_ENTRY call in the system call entry path.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
An earlier patch from Jens Osterkamp attempted to fix GDB
watchpoints by enabling the DABRX register at boot time.
Unfortunately, this did not work on SMP setups, where
secondary CPUs were still using the power-on DABRX value.
This introduces the same change for secondary CPUs on cell
as well.
Reported-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Tested-by: Ulrich Weigand <Ulrich.Weigand@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens
on a CPU other than the initial boot CPU. It turns out that this is the
result of mpic_init trying to set affinity of each interrupt vector to the
current boot CPU.
As far as I can tell, the same problem is likely to exist on any
secondary MPIC, because they have to deliver interrupts to the first
output all the time. There are two potential solutions for this: either
not set up affinity at all for secondary MPICs, or assume that a single
CPU output is connected to the upstream interrupt controller and hardcode
affinity to that per architecture.
This patch implements the second approach, defaulting to the first output.
Currently, all known secondary MPICs are routed to their upstream port
using the first destination, so we hardcode that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MSI capture logic for the axon bridge can sometimes
lose interrupts in case of high DMA and interrupt load,
when it signals an MSI interrupt to the MPIC interrupt
controller while we are already handling another MSI.
Each MSI vector gets written into a FIFO buffer in main
memory using DMA, and that DMA access is normally flushed
by the actual interrupt packet on the IOIF. An MMIO
register in the MSIC holds the position of the last
entry in the FIFO buffer that was written. However,
reading that position does not flush the DMA, so that
we can observe stale data in the buffer.
In a stress test, we have observed the DMA to arrive
up to 14 microseconds after reading the register.
This patch works around this problem by retrying the
access to the FIFO buffer.
We can reliably detect the conditioning by writing
an invalid MSI vector into the FIFO buffer after
reading from it, assuming that all MSIs we get
are valid. After detecting an invalid MSI vector,
we udelay(1) in the interrupt cascade for up to
100 times before giving up.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I got a bug report about a distro kernel not booting on a particular
machine. It would freeze during boot:
> ...
> Could not find start_pfn for node 1
> [boot]0015 Setup Done
> Built 2 zonelists in Node order, mobility grouping on. Total pages: 123783
> Policy zone: DMA
> Kernel command line:
> [boot]0020 XICS Init
> [boot]0021 XICS Done
> PID hash table entries: 4096 (order: 12, 32768 bytes)
> clocksource: timebase mult[7d0000] shift[22] registered
> Console: colour dummy device 80x25
> console handover: boot [udbg0] -> real [hvc0]
> Dentry cache hash table entries: 1048576 (order: 7, 8388608 bytes)
> Inode-cache hash table entries: 524288 (order: 6, 4194304 bytes)
> freeing bootmem node 0
I've reproduced this on 2.6.27.7. It is caused by commit
8f64e1f2d1 ("powerpc: Reserve in bootmem
lmb reserved regions that cross NUMA nodes").
The problem is that Jon took a loop which was (in pseudocode):
for_each_node(nid)
NODE_DATA(nid) = careful_alloc(nid);
setup_bootmem(nid);
reserve_node_bootmem(nid);
and broke it up into:
for_each_node(nid)
NODE_DATA(nid) = careful_alloc(nid);
setup_bootmem(nid);
for_each_node(nid)
reserve_node_bootmem(nid);
The issue comes in when the 'careful_alloc()' is called on a node with
no memory. It falls back to using bootmem from a previously-initialized
node. But, bootmem has not yet been reserved when Jon's patch is
applied. It gives back bogus memory (0xc000000000000000) and pukes
later in boot.
The following patch collapses the loop back together. It also breaks
the mark_reserved_regions_for_nid() code out into a function and adds
some comments. I think a huge part of introducing this bug is because
for loop was too long and hard to read.
The actual bug fix here is the:
+ if (end_pfn <= node->node_start_pfn ||
+ start_pfn >= node_end_pfn)
+ continue;
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, some PCIe devices on POWER6 machines do not get interrupts
assigned correctly. The problem is that OF doesn't create an
"interrupt" property for them. The fix is for of_irq_map_pci to fall
back to using the value in the PCI interrupt-pin register in config
space, as we do when there is no OF device-tree node for the device.
I have verified that this works fine with a pair of Squib-E SAS
adapter on a P6-570.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
parisc: struct device - replace bus_id with dev_name(), dev_set_name()
parisc: fix kernel crash when unwinding a userspace process
parisc: __kernel_time_t is always long
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq.h: fix missing/extra kernel-doc
genirq: __irq_set_trigger: change pr_warning to pr_debug
irq: fix typo
x86: apic honour irq affinity which was set in early boot
genirq: fix the affinity setting in setup_irq
genirq: keep affinities set from userspace across free/request_irq()
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: always define DECLARE_PCI_UNMAP* macros
x86: fixup config space size of CPU functions for AMD family 11h
x86, bts: fix wrmsr and spinlock over kmalloc
x86, pebs: fix PEBS record size configuration
x86, bts: turn macro into static inline function
x86, bts: exclude ds.c from build when disabled
arch/x86/kernel/pci-calgary_64.c: change simple_strtol to simple_strtoul
x86: use limited register constraint for setnz
xen: pin correct PGD on suspend
x86: revert irq number limitation
x86: fixing __cpuinit/__init tangle, xsave_cntxt_init()
x86: fix __cpuinit/__init tangle in init_thread_xstate()
oprofile: fix an overflow in ppro code
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: ignore out-of-range PstateStatus value
[CPUFREQ] Documentation: Add Blackfin to list of supported processors
Compress a set of consecutive switch cases into a case-range.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All architectures now use the generic compat_sys_ptrace, as should every
new architecture that needs 32bit compat (if we'll ever get another).
Remove the now superflous __ARCH_WANT_COMPAT_SYS_PTRACE define, and also
kill a comment about __ARCH_SYS_PTRACE that was added after
__ARCH_SYS_PTRACE was already gone.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... so get xen-ops.h in agreement with xen/smp.c
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual "introduce .text.head, put it in front of TEXT_TEXT in vmlinux.lds.S,
make the stuff up to jump to start_kernel live in it", same as on other
targets.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
switch to __init for those; unlike powerpc sparc has no hotplug support
for that stuff and their ->probe() tends to call __init functions while
being declared __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All noise since we don't have CPU hotplug there. However, they
did expose something very odd-looking in there - poke_viking()
does a bunch of identical btfixup each time it's called (i.e.
for each CPU). That one is left alone for now; just the trivial
misannotation fixes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
called only from __init, calls __init. Incidentally, it ought to be static
in file.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pure noise - alpha doesn't have CPU hotplug
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix boot crash on AMD IOMMU if CONFIG_GART_IOMMU is off
Currently these macros evaluate to a no-op except the kernel is compiled
with GART or Calgary support. But we also need these macros when we have
SWIOTLB, VT-d or AMD IOMMU in the kernel. Since we always compile at
least with SWIOTLB we can define these macros always.
This patch is also for stable backport for the same reason the SWIOTLB
default selection patch is.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
