Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some function pointers for a few PHY operations (for 82578 and 82567) and
were set incorrectly causing functions to be executed that were accessing
incorrect PHY register offsets for that particular device. This patch also
moves a few PHY-specific functions from ich8lan.c to the more appropriate
phy.c.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workaround that detects the correct PHY ID when an initial read of the
PHY ID registers returns an invalid one should retry up to ten times with
a small delay between attempts using a single PHY address and then repeat
using the remaining possible PHY addresses. Do this instead of trying each
possible PHY address repeating that up to 100 times.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function pointers for 8257x devices are not set. This is not really a
problem now because there is nothing in the driver that references the
pointers for this particular MAC-family (the appropriate functions are
called directly), but the pointers should be set in case they are used in
the future.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In testing we have found that skb_dma_map/unmap is incompatible with HW
IOMMU due to the fact that multiple mappings will return different results.
In order to correct this we need to remove skb_dma_map/unmap calls from the
e1000e driver.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use the sizeof the pointer to clear the result
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the case for 82577 because it does not support the ability to check
for downshift. Add case for e1000_phy_bm which can do this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some helpful debug messages.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new PCI device ID is for a new combination of MAC and PHY both of
which already have supporting code in the driver, just not yet in this
combination. During validation of the device, an intermittent issue was
discovered with waking it from a suspended state which can be resolved with
the pre-existing workaround to disable gigabit speed prior to suspending.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that the link state (as reported in
mac->serdes_has_link) will transition to false when autoneg fails to
complete but valid codewords were detected.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The different families (80003es2lan, 8257x, ICHx/PCH) supported by the
driver each have their own conditions when the PHY can be powered down.
This patch rewrites the PHY power up/down code to fit with the family-
specific style used in the driver. All pre-existing calls to power up or
down the PHY remain untouched. A new call to power down the PHY when
removing the driver when the interface is down replaces the current call
to reset the PHY in order to reduce power consumption.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two MAC-families that have VLAN filter table register arrays manage
each a bit differently from one another, so provide family-specific
functions for managing the register arrays and function pointers to access
the appropriate function. Also make sure attempts to access these
register arrays are not done on parts not supporting that feature.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx unit hang detection code in e1000e detects other hangs caused by
hardware components (e.g. Rx, DMA units), but it is not possible to detect
exactly which component is hung so it has always assumed a Tx unit hang.
When dumping a message to the system log because of a hang, this patch adds
more data to help narrow the cause of the issue and makes the message
non-Tx-specific. Because this new code reads PHY registers which can
sleep, move it off to a workqueue. This and all previously existing work
tasks in the driver are now cancelled when the driver is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mutex_lock() calls might_sleep() the driver doesn't have to here.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A failure to initialize the identification LED is not a fatal condition and
should allow the init path to continue.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was pointed out a pm_qos DMA latency requirement set when the driver is
loaded when parts that support early receive of jumbo frames are probed
could have that requirement overidden if another part supported by the
driver (one that does not support early receive of jumbo frames) is probed
later. Change the DMA latency requirement to be per-interface if needed
instead of per driver.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000_clear_hw_cntrs_*() functions read the registers to clear them.
There is no reason to save the register contents so the temp variable can
be removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set booleans to 'true' or 'false' to make it clear it is a boolean. Also
change instances of TRUE/FALSE in comments to lowercase true/false.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy and nvm operations structures have function pointers that contain
"phy" and "nvm" in the pointer names which are redundant since the
structures are already obviously in phy and nvm structures.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch depends on a previous one that cleans up redundant #includes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was only updating MII stats when an LSC up was detected and
the interface had not already been reported up to netdev. This meant
MII stats returned in response to an SIOCGMIIREG ioctl would always
show a link up if it had ever been up. This was misleading the networking
daemon guessnet, which uses this ioctl, into making improper network port
selections.
This fix adds a call to e1000_phy_read_status() to actively read the
mii stats before responding to the SIOCGMIIREG ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing the ethtool PHY loopback test on PCH-based LOMs (82577 and
82578), disable K1 (a MAC-PHY interconnect low power mode) otherwise
packets might get corrupted.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The e1000_get_cable_length_82577() should return a negative value upon
error.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copper links with WoL or management enabled (any condition which prevents
the phy from being powered down when the interface is taken down) were
always reporting link-up when the interface had been taken down. This
is because when the interface is taken down (ifconfig ethx down),
interrupts are disabled. With no interrupts, there is no LSC interrupt,
which is normally required to set "get_link_status", which instructs the
driver to query the device for link state. The fix is to force
get_link_status to true if the interface is not up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using legacy interrupts, do not clean the Rx ring while resetting
otherwise traffic will not pass.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide missing function pointers for ethtool set/get offloads.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clearing the interrupt timers following an IMS clear has the unwanted
side-effect of flushing all descriptors immediately following a partial
write when interrupts are disabled.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tests for 82583 in a couple ethtool functions that were missed from the
initial hardware enablement submission.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting WoL feature, check the supplied modes are all supported rather
than checking for no support. This way, if any new modes are added the
driver does not default to not complaining about it if we don't really
support it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the OEM bits in the PHY on 82577/82578, do not restart
autonegotiation if the firmware is blocking it (e.g. when an IDE-R session
is active) because the link must not go down.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A workaround for pre-release versions of 82577 is causing link issues on
some switches. The workaround is no longer needed on production parts so
remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing MTU, save it off prior to resetting otherwise the flow control
thresholds may be miscalculated.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some devices (e.g. 82578) not having a Tx timeout factor when linked at
100Mbps can cause false reports of hardware hangs on busy hubs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When flow control (pause) parameters were changed via ethtool (i.e. enabled
or disabled), the newly calculated thresholds were not being written to the
device for non-fiber media.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary workaround that mistakenly does not perform a page
select operation for PHY registers 29 and 30 (assuming these are the PHY
debug port address and data registers) on 82578 which can cause reads
of the Transmit with No Carrier Sense statistics register on page 778 to be
read from an incorrect page. Also error out if the page select operation
fails.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ec2a2b80f broke Tx/Rx when using
jumbo frames on certain parts (i.e. only PAUSE frames could be exchanged
once the high water mark was reached preventing normal packet traffic).
This patch reverts the breakage and sets appropriate high and low water
marks of the Rx FIFO for 82577/82578 which require a workaround due to a
flow control issue in hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reworks a previous workaround (commit 7d3cabbcc) for an issue
in hardware where noise on the interconnect between the MAC and PHY could
be generated by a lower power mode (K1) at 1000Mbps resulting in bad
packets. Disable K1 while at 1000 Mbps but keep it enabled for 10/100Mbps
and when the cable is disconnected. The original version of this
workaround was found to be incomplete.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On PCH-based (82577/82578) and some ICH8-based parts (82566) there is an
issue with the hardware automatically configuring the PHY with contents
from the EEPROM after the PHY is reset, so do the configuration by the
driver instead. This was already similarly done for some 82566 parts in
e1000_phy_hw_reset_ich8lan() but needs to be done after other resets,
so move the PHY configuration code to its own function and call after
all PHY resets.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing flow control (pause) parameters, the flow control thresholds
(i.e. when to send XON/XOFF frames) may not be setup correctly on parts
with copper media. Call the existing e1000_set_fc_watermarks()
function to set these thresholds.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
