This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes interrupt priority tables from the intc code.
Optimal priority assignment varies with embedded application anyway,
so keeping the interrupt priority tables together with cpu-specific
code doesn't make sense.
The function intc_set_priority() should be used instead to set the
desired interrupt priority level.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the intc core improved it is now possible to put the intc data
structures in the initdata section.
Version two of this patch puts the __initdata inside DECLARE_INTC_DESC()
and removes the __initdata included in the board specific r2d code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need a secondary register member in struct intc_prio_reg to support
dual priority registers used by ipi on x3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All SH-4 parts have a 4-digit year, while the SH-3 parts typically
only use a 2-digit one. The SH7705, SH7710, and SH7712 SH-3 parts
however opted to extend it to 4-digit and still look and act like
an SH-3 RTC in all other ways.
This adds a capability flag (RTC_CAP_4_DIGIT_YEAR) that these
corner-case CPU subtypes can set in their platform data and cleans
up some of the ifdef mess in the driver as a result.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The intc tables for sh3 currently contain a typo where the bit
fields in IPRD are mixed up for IRQ4 and IRQ5. This patch makes
sure the correct bit fields are used - all according to the
datasheets.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for
sh7705 from ipr to intc. While at it new vectors are added to
match the information provided by the datasheet.
Vectors for IRQ4 and IRQ5 are enabled by default.
Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also adds sh7705 specific platform data for the rtc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch unifies the cpu specific interrupt setup functions for
interrupt controller blocks such as ipr, intc2 and intc. There is no
point in having separate functions for each interrupt controller, so
let's clean this up.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the ipr code by grouping the offset array together
with the ipr_data structure in a new data structure called ipr_desc.
This new structure also contains the name of the controller in struct
irq_chip. The idea behind putting struct irq_chip in there is that we
can use offsetof() to locate the base addresses in the irq_chip
callbacks. This strategy has much in common with the recently merged
intc2 code.
One logic change has been made - the original ipr code enabled the
interrupts by default but with this patch they are all disabled by
default.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up SH7705 CPU support and the SE7705 board
for some of the recent changes.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some simple setup code for most of the CPU subtypes,
primarily simple platform device registration.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Magnus Damm