OMAP3 has three HS USB ports so it can have three different regulator
for each PHY connected to each port.
Currently these regulators are assumed to be optional and driver doesn't
fail but continue with the initialization if it doesn't get any regulators.
Regulator supply names has to be mapped in board files as 'hsusbN' where
'N' is port number and can be {0, 1 ,2}.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the board might use external Vbus power supply on musb
interface which would require to program ULPI_BUSCONTROL register.
Adding 'extvbus' flag which can be set from such boards which will
be checked at musb driver files before programming ULPI_BUSCONTROL.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Save dynamic FIFO read only information for later uses during
musb_save/restore_context functions.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB's programming guide dictates how we should handle its
irqs and in which order. Follow that.
Signed-off-by: Arnaud Mandy <ext-arnaud.2.mandy@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The version applied had a few comments which are now
done.
Thanks to Sergei for pointing out.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the Tx abort/teardown logic. We now wait for the teardown
completion interrupt and acknowledge the same by setting the tx_complete
register to 0.
This change is needed to ensure that abort processing works on DM365 platform.
Without this change after completion of abort processing the system is
overwhelmed with continuous stream of abort interrupts.
This change has been tested on all CPPI3.x platforms (DM644x, DM646x, DM35x,
DM36x).
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch implements the work around for a Mentor controller related
bug where it's observed a BULK Tx toggle error on the bus when a
BULK IO gets scheduled on an endpoint that was earlier used for
handling ISOC transaction and needed to start on 1 toggle. When such
a situation arises even if the TXCSR toggle bits are programmed
correctly by the musb driver the data gets transmitted with 0 toggle
which leads to toggle error on the bus and the BULK transaction fails.
In case of MSC write, the device gets reset by the Host.
This Mentor bug is observed on almost all Mentor versions (1.3, 1.5,
1.8). Confirmed on DM644x, DM355, DM365, OMAPL13x platforms.
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB DMA_INTR register may sometimes read zero when infact there
was a pending interrupt. Workaround this by reading the DMA_COUNT
values for all enabled channels when this condition occurs.
Flag these channels as the ones needing to be serviced.
Additionally, the absence of a debug print meant we would never
catch a spurious DMA interrupt in MUSB. So this patch adds a
debug print in the IRQ handler.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a wrapper for reading the DMA count register, analogous
to the one for writing to this register.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We have observed MSC data read corruption when USB LAN device is
also connected and it's interface is up.
Silicon team has confirmed an errata where in all the active
transfers should use FIFO space either in first 8K or next 8K.
So far we have observed the issue in above use case scenario.
As a workaround to it, adding a new FIFO config (5) fitting well
within first 8K which can be used for such use cases.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
move to request_threaded_irq() on twl4030 children.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under the new system a device cannot be suspended against
the driver's wish. Therefore this condition no longer needs
to be checked for.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Return values are being initialised to zero only to be unconditionally
assigned to a few instructions later. This may give the impression that
zero is returned on success, which is not the case.
Note also that ftdi_NDI_device_setup never reports errors.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also remove unnecessary buffer allocations for zero-length transfers.
Reported-by: Matti Aarnio <matti.aarnio@zmailer.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also fixes DMA transfer to stack for latency buffer.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's really the wireless speed, so rename the thing to make
more sense. Based on a recommendation from David Vrabel
Cc: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently a non-root-hub USB device's wakeup settings are initialized when the
device is set to a configured state using device_init_wakeup(), but this is not
correct as wakeup is split into "capable" (can_wakeup) and "enabled"
(should_wakeup). The settings should be initialized instead in the device
initialization (usb_new_device) with the "capable" setting disabled and the
"enabled" setting enabled. The "capable" setting should be set based on the
device being configured or unconfigured, and "enabled" setting set based on
the sysfs power/wakeup control.
This patch retains the sysfs power/wakeup setting of a non-root-hub USB device
over a USB device re-configuration, which can happen (for example) after a
suspend/resume cycle.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pbLua console port is known to not be a modem, so it is
unnecessary to be told this when it is plugged in.
Add NOT_A_MODEM quirk to tell the driver that we know this already
and hence not to warn us, and mark the pbLua console port.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pbLua firmware (http://pblua.com/) for the Lego Mindstorms NXT
provides a CDC ACM port for it's serial console.
This used to be detected automatically, but this support has been
dropped, probably for sensible reasons.
Explicitly add support for this device by adding an item to the
device ID table.
Signed-off-by: Julian Calaby <julian.calaby@gmail.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Due to a simple oversight when bus zero was added, the text API fails to
deliver the bus number in 'E' messages (which are equivalent of 'C'
messages, only for error case). This makes it harder, for instance,
use a search-and-highlight in a text editor. So fix it.
Also, Alan Stern requested adding timestamps to 'E' messages. This is
purely cosmetic, but makes it easier to read the trace. This is done
for both text and binary APIs.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's easier to keep up and add more sysfs entries
as necessary.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Normally, the musb uses ep1 as the bidirectional bulk endpoint. This won't
work on the Blackfin musb as all endpoints (except ep0) are unidirectional.
Further, ep1-ep4 have a small 128 byte FIFO which makes them undesirable
for bulk endpoints (which need more like a 512 byte FIFO). This leaves us
with ep5-ep7 which have 1024 byte FIFOs and can be configured as either
in/out and bulk/interrupt/iso on the fly.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've got a crappy cypress converter here, and while running at higher
baud rates craps out on throughput, it works fine with lower ones.
While it'd be nice to simply use a lower baud rate, not all devices
can be configured this way, and it is possible to (slowly) interact
at higher rates by sending a byte at a time. So let people force
higher rates when they need it via a module parameter.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current code has a confusing duplicate new_baudrate init when setting
the serial parameters. So just combine the if statement checks to avoid
this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB_SERIAL_DEBUG Kconfig is for the USB serial debug driver, not for
generically enabling debug output in random USB serial drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices which use mode switching revert to their
primary mode as they are reset. They must not be reset for
error handling. As user spaces makes the switch it also
has to tell the kernel that a device is quirky.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices must be switched to a new mode to fully use them.
A reset would make them revert to the old mode. Therefore a reset
must not be used for error handling with such devices.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it's expected that the transceiver driver will
initialize and call the notifier chain when
necessary. Implement that for twl4030-usb driver.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
An incorrect sizeof() resulted in only 4 (or 8) octets of the CHID being
checked instead of all 16 octets. A randomly generated CHID had a
probability of being unable to start a WUSB host of less than 1 in
2 billion.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
xhci_add_endpoint() is used in the reset path. It must
use GFP_NOIO to avoid a possible deadlock.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update cdc-acm to the async methods eliminating the workqueue
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use platform_get_resource() to fetch the memory resource and
resource_size() for calculate the length.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use resource_size().
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EHCI FSL controller preserve its state during sleep mode, so nothing
fancy needs to be done.
Though, during 'deep sleep' mode (as found in MPC831x CPUs) the
controller turns off and needs to be reinitialized upon resume.
This patch adds support for hibernation and resuming after deep sleep.
Based on Dave Liu and Jerry Huang's work[1].
[1] http://www.bitshrine.org/gpp/linux-fsl-2.6.24.3-MPC8315ERDB-usb-power-mangement.patch
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes following warnings:
ehci-fsl.c:43:5: warning: symbol 'usb_hcd_fsl_probe' was not declared. Should it be static?
ehci-fsl.c:150:6: warning: symbol 'usb_hcd_fsl_remove' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fix audio record functionality for some Full speed sound blaster devices.
Issue: Sometimes transaction complete indication is coming from HW one frame later.
Solution: If scan_periodic process now frame or previous frame now-1 and sitd transaction
is not finished yet, exit scan_periodic function and check the same transaction in the next frame.
Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Sometimes disable_periodic() stop scan_periodic before than free_cached_itd_list() was called.
In such case USB Host stacked during disconnect operation
Solution: add call of free_cached_itd_list() function in disable_periodic()
Signed-off-by: Dimitry Epshtein <dima@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new host controller driver method, reset_device(), that the USB core
will use to notify the host of a successful device reset. The call may
fail due to out-of-memory errors; attempt the port reset sequence again if
that happens. Update hub_port_init() to allow resetting a configured
device.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When a USB device is reset, the xHCI hardware must know, in order to match
the device state and disable all endpoints except control endpoint 0.
Issue a Reset Device command after a USB device is successfully reset.
Wait on the command to finish, and then cache or free the disabled
endpoint rings.
There are four different USB device states that the xHCI hardware tracks:
- disabled/enabled - device connection has just been detected,
- default - the device has been reset and has an address of 0,
- addressed - the device has a non-zero address but no configuration has
been set,
- configured - a set configuration succeeded.
The USB core may issue a port reset when a device is in any state, but the
Reset Device command will fail for a 0.96 xHC if the device is not in the
addressed or configured state. Don't consider this failure as an error,
but don't free any endpoint rings if this command fails.
A storage driver may request that the USB device be reset during error
handling, so use GPF_NOIO instead of GPF_KERNEL while allocating memory
for the Reset Device command.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the hub emulation code to allow ports on an xHCI root hub to be
disabled. Add the code to clear the port enabled/disabled bit, and clear
the port enabled/disabled change bit. Like EHCI, the port cannot be
enabled by setting the port enabled/disabled bit. Instead, a port is
enabled by the host controller after a reset.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor the code to clear the port change bits in the port status
register. All port status change bits are write one to clear.
Remove a redundant port status read that was supposed to unblock any
posted writes. We read the port after the write to get the updated status
for debugging, so the port read after that is unnecessary.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
All commands that can be issued to the xHCI hardware can come back with
vendor-specific "informational" completion codes. These are to be treated
like a successful completion code. Refactor out the code to test for the
range of these codes and print debugging messages.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The xhci_command structure is the basic structure for issuing commands to
the xHCI hardware. It contains a struct completion (so that the issuing
function can wait on the command), command status, and a input context
that is used to pass information to the hardware. Not all commands need
the input context, so make it optional to allocate. Allow
xhci_free_container_ctx() to be passed a NULL input context, to make
freeing the xhci_command structure simple.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Refactor out the code to cache or free endpoint rings from recently
dropped or disabled endpoints. This code will be used by a new function
to reset a device and disable all endpoints except control endpoint 0.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we fail to queue an evaluate context command or a configure endpoint
command to the command ring in xhci_configure_endpoint(), we need to
remove the xhci_command structure from the device's command list before
returning. If the command is left on the command list, it will sit there
indefinitely, blocking commands submitted after this fails.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1316) adds some error checking to usb_submit_urb().
It's conditional on CONFIG_USB_DEBUG, so it won't affect normal users.
The new check makes sure that the actual type of the endpoint
described by urb->pipe agrees with the type encoded in the pipe value.
The USB error code documentation is updated to include the code
returned by the new check, and the usbfs SUBMITURB handler is updated
to use the correct pipe type when legacy user code tries to submit a
bulk transfer to an interrupt endpoint.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My distro kernel (Fedora Rawhide) started throwing warnings from DMA API
checker, so I have no choice but band-aid it quick. There's no attempt
to reuse DMA buffers. Control messages are only sent rarely anyway.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
hardware reports wrong interrupt. Although such a situation should not
happen, the compiler complains about this access.
This patch adds a sanity check and generates warning to detect such
issues.
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On various mxc boards, the intial ULPI reads resulted in a timeout
which prevented the transceiver to be identified and thus the ehci
device to be probed.
Initializing the hardware lines connected to the transceiver (through
pdata->init call) before actually enabling clocks and configuring
registers in the devices fixes this problem.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Removed CS5 and CS6 from data bits since these are not supported
in FTDI hardware.
Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Latency timeout was read but never stored on port probe. When
ASYNC_LOW_LATENCY was cleared the device timeout would get set to 0
rather than the default 16ms.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We always push characters to ldisc immediately regardless of
ASYNC_LOW_LATENCY.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Resubmitting read urb fails with -EPERM if completion handler runs while
urb is being killed on close. This should not be reported as an error.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changes:
Return an empty string for modulation
when there is no connection
Fix sysfs unload race conditions
Log firmware load process, remove delay
Add new configuration interface
Remove cxacru-cf.bin
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has never worked properly because wsize passed to
cxacru_cm() is incorrectly set to the number of values
instead of the data bytes. The maximum number of values
that can be set at once is 7 which means the device will
not get enough data to work with and none of the
configuration values will be used.
At least one existing cxacru-cf.bin file contains invalid
data which will prevent the modem from syncing properly.
Fixing it is likely to break existing systems, and the
new sysfs interface for setting configuration parameters
can provide the same functionality. A script is provided
to convert from the original format.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The modem can be configured using CM_REQUEST_CARD_DATA_SET,
although CM_REQUEST_CARD_DATA_GET does not return any data.
Tested by setting the modulation (0x0a) option.
There is a list of parameters in the following archive,
but the meaning of many of them is not well documented:
http://sourceforge.net/project/shownotes.php?release_id=301825
This source also indicates that the highest parameter set
is 0x4a but this varies by model so an arbitrary limit of
0x7f has been used (the index is a 32-bit integer).
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Firmware writing takes 256ms per 4KB with OHCI, which
is very slow compared to 7ms per 4KB with UHCI.
Until I have access to a hardware USB analyser it may
not be possible to determine why this happens.
Instead of appearing to do nothing, log progress when
writing firmware and then log the ATM device information
when finished. Remove an unnecessary 4 second delay.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These commands were found by accident... fortunately
it still works even if the flash memory is erased,
despite having no USB device IDs.
Some example sysfs code for raw command access:
http://simon.arlott.org/pub/cxacru/raw.c
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is possible for usb_get_intfdata() to return NULL if
sysfs is accessed while the module is being unloaded or
the device is being removed.
Move the access code to an inline function in usbatm.h,
and return -ENODEV if any of the pointers are NULL.
It should not be possible for the instance data or atm
device to be invalid until after unbind() completes and
the sysfs attributes have been removed.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When attempting to read data that is not actually
an array of values, the length may be negative
which causes an Oops due to a likely access off
the end of the data array.
This bug should not occur under normal use unless
the device returns an invalid response.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When there is no connection, return an empty string
instead of "0" for the connection modulation.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver is a Full / Low speed only USB host for the i.MX21.
Signed-off-by: Martin Fuzzey <mfuzzey@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently if the driver fails to register on port, the kernel
crashes with the following stack:
cpu 0x1: Vector: 300 (Data Access) at [c0000000e0303090]
pc: c00000000039aa74: .__mutex_lock_slowpath+0x44/0x10c
lr: c00000000039aa58: .__mutex_lock_slowpath+0x28/0x10c
[c0000000e03033c0] c00000000026b074 .uart_remove_one_port+0xbc/0x16c
[c0000000e0303460] d0000000000e0554 .jsm_remove_uart_port+0x8c/0x10c [jsm]
[c0000000e03034f0] d0000000000dc034 .jsm_remove_one+0x34/0x108 [jsm]
[c0000000e0303590] c0000000001f4aa0 .pci_device_remove+0x48/0x74
...
This patch just fixes the code flow to abort the load when an
error is detected.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If jsm fails to load, then remove the uart stuff, otherwise,
the things (as files), will be there forever (even when the module
is unloaded). If you try to reload the module, the following message
appears:
kobject_add_internal failed for ttyn1 with -EEXIST, don't try to
register things with the same name in the same directory.
This patch remove the uart things when the driver fails.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This new VT mode (VT_PROCESS_AUTO) does everything that VT_PROCESS does
except that it doesn't wait for a VT_RELDISP ioctl before switching
away from a VT with that mode.
If the X server eventually uses this new mode, debugging and crash
recovery should become easier. This is because even when currently in
the VT of a frozen X server it would still be possible to switch out
by doing SysRq-r and then CTRL-<number of a text vt>, sshing in and
doing chvt <number of a text vt>, or any other method of VT switching.
The general concensus on #xorg-devel seems to be that it should be
safe to use this with X now that we have KMS.
This also moves the VT_ACKACQ define to a more appropriate place,
for clarity's sake.
Signed-off-by: Ari Entlich <atrigent@ccs.neu.edu>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We allocate during interrupts so while our buffering is normally diced up
small anyway on some hardware at speed we can pressure the VM excessively
for page pairs. We don't really need big buffers to be linear so don't try
so hard.
In order to make this work well we will tidy up excess callers to request_room,
which cannot itself enforce this break up.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was noticed by Matthias Urlichs and he proposed a fix. This patch
does the fixing a different way to avoid introducing several new race
conditions into the code.
The problem case is TTY_DRIVER_RESET_TERMIOS = 0. In that case while we
abort the ldisc change, the hangup processing has not cleaned up and restarted
the ldisc either.
We can't restart the ldisc stuff in the set_ldisc as we don't know what
the hangup did and may touch stuff we shouldn't as we are no longer
supposed to influence the tty at that point in case it has been re-opened
before we get rescheduled.
Instead do it the simple way. Always re-init the ldisc on the hangup, but
use TTY_DRIVER_RESET_TERMIOS to indicate that we should force N_TTY.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MFD_TIMBERDALE doesn't appear to be defined anywhere. However the code in
question can build happily without platform specifics so remove the check
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original author didn't realise the kernel lock was a drop while sleep
lock so did clever (and wrong) things to work around the non need to avoid
deadlocks. Remove the cleverness and the comment (as we don't hold the BKL
now anyway in those paths)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Nozomi tty handling is very broken on the open/close side (See
http://bugzilla.kernel.org/show_bug.cgi?id=13024 for one example). In
particular it marks the tty as closed on the first close() not on the last.
Most of the logic is pretty solid except for the open/close path so switch
to the tty_port helpers and let them do all the heavy lifting. This is also
fixes all the POSIX behaviour violations in the open/close paths.
Begin by adding the tty port usage
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revised patch to use the new kfifo API. This replaces the one that was dropped
from -next due to collisions with the kfifo API changes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bcm6358 CPU has two uarts, make it possible to use the second one.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we always check for gdb breaks even when it isn't active, we get false
positives on normal code and the system panics.
URL: http://blackfin.uclinux.org/gf/tracker/5277
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we don't disable the DMA TX channel, an inopportune timeout will
trigger the interrupt handler and may cause a dead lock with the spin_lock.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For UARTs that have dedicated hardware flow control support, there will be
no gpios to request/free as they are part of the normal peripheral pins.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found a potential null dereference in mgsl_put_char and
mgsl_write. There is a check for tty being NULL, but it is
dereferenced earlier.
Actually, tty cannot be NULL in .write and .put_char, so remove
the tests.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stephen Rothwell found the following warning (x86_64 allmodconfig):
drivers/char/ip2/ip2main.c:511: warning: 'ip2_setup' defined but not used
This patch adds module parameter to fix the above warning.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the kernel command line we can pass "module parameters". So #ifdef
MODULE is obsolute now. Remove it completely. When CONFIG_PCI=n and
building ip2main.c then we are hit by the following warning. So move
*pdev into #ifdef CONFIG_PCI.
drivers/char/ip2/ip2main.c: In function `ip2_loadmain':
drivers/char/ip2/ip2main.c:542: warning: unused variable `pdev'
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Acked-by: Michael H. Warfield <mhw@WittsEnd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can pass "module parameters" on the kernel command line even when
!MODULE. So, #ifdef MODULE becomes obsolete. Also move the declaration
moxa_board_conf at the start of the function, since we were hit by the
following warning.
drivers/char/moxa.c: In function `moxa_init':
drivers/char/moxa.c:1040: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Rakib Mullick<rakib.mullick@gmail.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vtermnos[] is unsigned, so this test was wrong.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Convert printks to pr_<level>
Convert some embedded function names to %s...__func__
Remove a period after exclamation points.
Remove #define pr_dbg which could be used by future kernel.h includes
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found unnecessary test in mxser_startup.
tty is dereferenced earlier, the test is superfluous. Remove it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With gcc 4.0.2:
drivers/char/cyclades.c: In function 'cyy_interrupt':
drivers/char/cyclades.c:581: warning: 'info' may be used uninitialized in this function
introduced by
: commit 3aeea5b922
: Author: Jiri Slaby <jirislaby@gmail.com>
: AuthorDate: Sat Sep 19 13:13:16 2009 -0700
: Commit: Live-CD User <linux@linux.site>
: CommitDate: Sat Sep 19 13:13:16 2009 -0700
:
: cyclades: introduce cyy_readb/writeb
In fact the true branch which uses uninitialized 'info' can never
happen because chip is always less than ->nchips and channel is
always less than 4 which we alloc.
So behave similar to rx handling and remove the test completely.
I wonder why gcc 4.4.1 doesn't spit a word.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The variables were unsigned so the tests did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add different model (with a different PCI ID) to support Korenix JetCard.
Signed-off-by: Kiros Yeh <kiros@korenix.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The platform code doesn't have to provide platform data to get sensible
default behaviour from the imx serial driver.
This patch does not handle NULL dereference in the IrDA case, which still
requires a valid platform data pointer (in imx_startup()/imx_shutdown()),
since I don't know whether there is a sensible default behaviour, or
should the operation just fail cleanly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oskar Schirmer <os@emlix.com>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is heavily based on an earlier patch found on the linux-serial
mailing list [1], written by Darius Augulis.
The previous incarnation of this patch only supported a 2x serial port
card. I have added support for my SYBA 6x serial port card, and tested on
x86.
[1]: http://marc.info/?l=linux-serial&m=124975806304760
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix transmit bug that could drop send data if write() called close to
serial transmitter going idle after sending previous data. Bug is caused
by incorrect use of device information member tx_count.
Driver originally processed one data block (write call) at a time, waiting
for transmit idle before sending more. tx_count recorded how much data
was loaded in DMA buffers on write(), and was cleared on send completion.
tx_count use was overloaded to record accumulated data from put_char()
callback when transmitter was idle.
A bug was introduced when transmit code was reworked to allow multiple
blocks of data in the tx DMA buffers which keeps transmitter from going
idle between blocks. tx_count was set to size of last block loaded,
cleared when tx went idle, and monitored to know when to restart
transmitter without proper synchronization. tx_count could be cleared
when unsent data remained in DMA buffers and transmitter required
restarting, effectively dropping unsent data.
Solution:
1. tx_count now used only to track accumulated data from put_char
2. DMA buffer state tracked by direct inspection of descriptors
with spinlock synchronization
3. consolidate these tasks in tx_load() :
a. check for available buffer space
b. load buffers
c. restart DMA and or serial transmitter as needed
These steps were previously duplicated in multiple places,
sometimes incompletely.
4. fix use of tx_count as active transmit indicator,
instead using tx_active which is meant for that purpose
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Permits using KGDB over the console with the atmel_serial driver.
[akpm@linux-foundation.org: s/barrier/cpu_relax/]
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This macro is a duplicate of ARRAY_SIZE defined in kernel api, so just use
that instead.
Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Augment the UPF_FIXED_TYPE logic, which currently applies to UART ports
provisioned using platform_device_register.
The suggested patch applies same logic into 'serial8250_register_ports',
making UART ports provisioned using early_serial_setup inherit their
properties from the uart_config entry.
Signed-off-by: Shmulik Ladkani <shmulik@jungo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fit blackfin uart over sport driver into common uart inftrastructure. It
is based on the early platform interfaces to get the platform data early
when the console is initilized.
1. Enable sport uart driver to change uart baud, data bit, stop bit at
runtime. Bind the index of uart device nodes to physical index of
sports.
2. Move all platform data into arch specific board files. Register
and probe platform device data in both early and normal stages.
3. Console is registered in sport uart driver as well.
4. Remove 500 us block waiting in sport tx stop code by putting a
dummy data into tx fifo to make sure the sport tx stops when all bytes
are shifted out except for the dummy data.
5. clean up a bit and fix up coding style.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit 11b897cf84 changed expected
pcmcia area addresses from the 32bit pseudo to the real 36bit
addresses, but did not update the comments.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Remoe the irq_list parameter from pd6729, as it can and should be set
via sysfs (and -- if available -- pcmciautils, which reads the information
from /etc/pcmcia/config.opts )
[linux@dominikbrodowski.net: updated commit message]
Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Indigos are well known for distortions when running on some buggy ENE
controllers. There is a workaround in the yenta driver, but for some
reason it isn't activated on CB712. However, I own a laptop with such
chip and it seems that it also is affected - I can clearly hear occasional
cracks, especially under heavy network load, and in Windows XP the card is
completely unusable.
This simple change fixed things for me.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=15191
[linux@dominikbrodowski.net: extend it to the other ENE bridges]
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This makes the COH 901 318 respect the scatter offset field by using
the sg_phys() rather than the sg_dma_address() so we get a pointer
to the actual data we want to send rather than the beginning of the
buffer. Also initialize the lli:s a bit more thoroughly.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This makes the COH 901 318 configure channel direction (to or from
device) dynamically, instead of being passed in from the platform
data. This was necessary in order to get the MMC/SD-card channel
bidirectional (all other channels on the U300 were either RX or
TX but this one was both). This also sets memcpy() alignent to
even 2^2 (32bit) boundaries, which makes the memcpy() stress tests
start working.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This removes the pointless irq counting for the COH 901 318, as
it turns out the hardware will only ever fire one IRQ for a linked
list anyway. In the process also a missing spinlock was introduced.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This centralize some spread-out initialization of descriptors into
one function and cleans up the error paths.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This cleans up the some debug code that was not working in the
COH 901 318 driver, adds some helpful comments and rearrange the
code a bit.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (214 commits)
omap2: Initialize Menelaus and MMC for N8X0
AM3517 EVM: correct typo - tca6416 mispelt as tca6516
AM3517 EVM: Enable I2C support
AM35x: Enable OMAP_MUX in defconfig
AM35x: Add missing GPIO mux config for EHCI port
Zoom3: Defconfig update
omap: i2c: Fix muxing for command line enabled bus
OMAP4: clock: Remove clock hacks from timer-gp.c
OMAP4: clock: Add dummy clock nodes for interface clocks
OMAP4: clock: Rename leaf clock nodes to end with a _ick or _fck
OMAP2+ clock: revise omap2_clk_{disable,enable}()
OMAP2/3 clock: combine OMAP2 & 3 boot-time MPU rate change code
OMAP clockdomain: if no autodeps exist, don't try to add or remove them
OMAP hwmod: add hwmod class support
OMAP hwmod: convert header files with static allocations into C files
OMAP hwmod: convert hwmod to use hardware clock names rather than clkdev dev+con
OMAP clock: add omap_clk_get_by_name() for use by OMAP hwmod core code
OMAP3: clock: add capability to change rate of dpll4_m5_ck_3630
OMAP4 clock: drop the ALWAYS_ENABLED clock flag
OMAP clock: drop RATE_FIXED clock flag
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6:
sparc: Support show_unhandled_signals.
sparc: use __ratelimit
sunxvr500: Additional PCI id for sunxvr500 driver
sparc: use asm-generic/scatterlist.h
sparc64: If 'slot-names' property exist, create sysfs PCI slot information.
sparc: remove trailing space in messages
sparc: remove redundant return statements
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1341 commits)
virtio_net: remove forgotten assignment
be2net: fix tx completion polling
sis190: fix cable detect via link status poll
net: fix protocol sk_buff field
bridge: Fix build error when IGMP_SNOOPING is not enabled
bnx2x: Tx barriers and locks
scm: Only support SCM_RIGHTS on unix domain sockets.
vhost-net: restart tx poll on sk_sndbuf full
vhost: fix get_user_pages_fast error handling
vhost: initialize log eventfd context pointer
vhost: logging thinko fix
wireless: convert to use netdev_for_each_mc_addr
ethtool: do not set some flags, if others failed
ipoib: returned back addrlen check for mc addresses
netlink: Adding inode field to /proc/net/netlink
axnet_cs: add new id
bridge: Make IGMP snooping depend upon BRIDGE.
bridge: Add multicast count/interval sysfs entries
bridge: Add hash elasticity/max sysfs entries
bridge: Add multicast_snooping sysfs toggle
...
Trivial conflicts in Documentation/feature-removal-schedule.txt
-tip testing found this build failure (x86 randconfig):
drivers/built-in.o: In function `setup_rfkill':
compal-laptop.c:(.text+0x36abe8): undefined reference to `rfkill_alloc'
compal-laptop.c:(.text+0x36abfc): undefined reference to `rfkill_register'
compal-laptop.c:(.text+0x36ac30): undefined reference to `rfkill_alloc'
compal-laptop.c:(.text+0x36ac44): undefined reference to `rfkill_register'
Which can happen with CONFIG_COMPAL_LAPTOP=y but COMPAL_LAPTOP=m.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is no longer needed. I missed to remove this in
567ec874d1 ("net: convert multiple
drivers to use netdev_for_each_mc_addr, part6")
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tx/mcc polling, napi_complete() is being incorrectly called
before reaping tx completions. This can cause tx compl processing
to be scheduled on another cpu concurrently which can result in a panic.
This if fixed by calling napi complete() after tx/mcc compl processing
but before re-enabling interrupts (via a cq notify).
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some sis190 devices don't report LinkChange, so do polling for
link status.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11926
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
i2c_master_send & i2c_master_recv do not support more than 64 kb
transfer, since msg.len is u16.
Signed-off-by: Zhangfei Gao <zgao6@marvell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Allow I2C drivers to make use of the runtime PM framework by adding
bus implementations of the runtime PM operations. These simply
immediately suspend when the device is idle. The runtime PM framework
provides drivers with off the shelf refcounts for enables and sysfs
control for managing runtime suspend from userspace so is useful even
without meaningful input from the bus.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for the SMBus alert mechanism to the i2c-parport-light
driver. The ADM1032 evaluation board at least is properly wired for
this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
Add support for the SMBus alert mechanism to the i2c-parport driver.
The ADM1032 evaluation board at least is properly wired for this.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
Having a separate Kconfig option for i2c-smbus makes it possible to
build that support as a module even when i2c-core itself is built-in.
Bus drivers which implement SMBus alert should select this option, so
in most cases this option is hidden and the user doesn't have to care
about it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
SMBus alert support. The SMBus alert protocol allows several SMBus
slave devices to share a single interrupt pin on the SMBus master,
while still allowing the master to know which slave triggered the
interrupt.
This is based on preliminary work by David Brownell. The key
difference between David's implementation and mine is that his was
part of i2c-core, while mine is split into a separate, standalone
module named i2c-smbus. The i2c-smbus module is meant to include
support for all SMBus extensions to the I2C protocol in the future.
The benefit of this approach is a zero cost for I2C bus segments which
do not need SMBus alert support. Where David's implementation
increased the size of struct i2c_adapter by 7% (40 bytes on i386),
mine doesn't touch it. Where David's implementation added over 150
lines of code to i2c-core (+10%), mine doesn't touch it. The only
change that touches all the users of the i2c subsystem is a new
callback in struct i2c_driver (common to both implementations.) I seem
to remember Trent was worried about the footprint of David'd
implementation, hopefully mine addresses the issue.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Trent Piepho <tpiepho@freescale.com>
When the i2c-parport adapter is reponsible for powering devices, it
would seem reasonable to give them some time to settle before trying
to access them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The description of the delay parameter is incomplete, it suggests that
there is a direct relation between the delay value and the bus
frequency. In fact, due to additional delays in the i2c bitbanging
code, the i2c clock is always much slower.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Till Harbaum <Till@Harbaum.org>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make initialization data also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
disable decl_init,const_decl_init;
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Instead of repeating the error unwinding steps in each place an error
can be detected, use the common idiom of gotos into an error flow.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can reduce the number of IB interrupts from two interrupts per
srp_queuecommand() call to one by using separate CQs for send and
receive completions and processing send completions by polling every
time a TX IU is allocated.
Receive completion events still trigger an interrupt.
Signed-off-by: Bart Van Assche <bart.vanassche@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Adds initial version of MPC512x DMA driver.
Only memory to memory transfers are currenly supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This adds Kconfig options for DEBUG and VERBOSE_DEBUG to the DMA
engine subsystem, I got tired of editing the Makefile manually
each time I want to debug things in here, modelled this on the
debug switches for other subsystems and works like a charm when
working on our DMA engines.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some new devices have extra keys, which we add to our list. Currently,
they all generate events that allow us to use a simple table/array,
without need for the sparse keymap.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (40 commits)
DaVinci DM365: Adding support for SPI EEPROM
DaVinci DM365: Adding DM365 SPI support
DaVinci DM355: Modifications to DM355 SPI support
DaVinci: SPI: Adding header file for SPI support.
davinci: dm646x: CDCE clocks: davinci_clk converted to clk_lookup
davinci: clkdev cleanup: remove clk_lookup wrapper, use clkdev_add_table()
DaVinci: DM365: Voice codec support for the DM365 SoC
davinci: clock: let clk->set_rate function sleep
Add SDA and SCL pin numbers to i2c platform data
davinci: da8xx/omap-l1xx: Add EDMA platform data for da850/omap-l138
davinci: build list of unused EDMA events dynamically
davinci: Fix edma_alloc_channel api for EDMA_CHANNEL_ANY case
davinci: Keep count of channel controllers on a platform
davinci: Correct return value of edma_alloc_channel api
davinci: add CDCE949 support on DM6467 EVM
davinci: add support for CDCE949 clock synthesizer
davinci: da850/omap-l138 EVM: register for suspend support
davinci: da850/omap-l138: add support for SoC suspend
davinci: add power management support
DaVinci: DM365: Changing default queue for DM365.
...
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (38 commits)
sata_via: Delay on vt6420 when starting ATAPI DMA write
ata: Detect Delkin Devices compact flash
pata_efar: Enable parallel scanning
pata_atiixp: enable parallel scan
[libata] pata_atiixp: add locking for parallel scanning
[libata] pata_efar: add locking for parallel scanning
libata: Pass host flags into the pci helper
[libata] pata_marvell: CONFIG_AHCI is really CONFIG_SATA_AHCI
libata: Allow pata_legacy to be built on non-ISA but PCI systems
pata_pdc202xx_old: fix UDMA mode for PDC2026x chipsets
pata_pdc202xx_old: fix UDMA mode for Promise UDMA33 cards
[libata] pata_at91: fix backslash-continued string
pata_via: store UDMA masks in via_isa_bridges table
pata_via: fix address setup timings underlocking
pata_serverworks: fix error message
pata_serverworks: fix PIO setup for the second channel
pata_efar: fix secondary port support
pata_cypress: fix PIO timings underclocking
pata_cs5535: use correct values for PIO1 and PIO2 data timings
pata_cmd64x: remove unused definitions
...
When writing a disc on certain lite-on dvd-writers (also rebadged
as optiarc/LG/...) connected to a vt6420, the ATAPI CDB ends
up in the datastream and on the disc, causing silent corruption.
Delaying between sending the CDB and starting DMA seems to
prevent this.
I do not know if there are burners that do not suffer from
this, but the patch should be safe for those as well.
There are many reports of this issue, but AFAICT no solution was
found before. For example:
http://lkml.indiana.edu/hypermail/linux/kernel/0802.3/0561.html
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Again originally proposed by Bartlomiej but this does it by using the
generic helper logic instead.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This was originally proposed by Bartlomiej but as a device specific
expansion of the init_one function rather than making the helper more
generic.
Enable the parallel scan via the generic flags.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is similar change as commit 60c3be3 for ata_piix host driver
and while pata_atiixp doesn't enable parallel scan yet the race
could probably also be triggered by requesting re-scanning of both
ports at the same time using SCSI sysfs interface.
[Ported to current tree without other patch dependancies by Alan Cox]
Original is
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one is
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add clearing of UDMA enable bit also for PIO modes and then add
extra locking for parallel scanning.
This is similar change as commit 60c3be3 for ata_piix host driver
and while pata_efar doesn't enable parallel scan yet the race could
probably also be triggered by requesting re-scanning of both ports
at the same time using SCSI sysfs interface.
[Ported to current kernel without other patch dependancies by
Alan Cox]
Original is
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
This one is
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This allows parallel scan and the like to be set without having to stop
using the existing full helper functions. This patch merely adds the argument
and fixes up the callers. It doesn't undo the special cases already in the
tree or add any new parallel callers.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The marvell driver comtains a fallback to ahci for the sata ports
which is incorrectly checked as CONFIG_AHCI while the only AHCI config
item is actually called SATA_AHCI (which also sounds sensible
considering it's a fallback for the sata ports).
Signed-off-by: Christoph Egger <siccegge@stud.informatik.uni-erlangen.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is needed for some unsupported hardware setups on strange 64bit
mainboards where crazy stuff has been done like putting flash ata adapters
on the LPC bus, or where the real hardware is hidden/confused.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PDC2026x chipsets need the same treatment as PDC20246 one.
This is completely untested but will hopefully fix UDMA issues
that people have been reporting against pata_pdc202xx_old for
the last couple of years.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
On Monday 04 January 2010 02:30:24 pm Russell King wrote:
> Found the problem - getting rid of the read of the alt status register
> after the command has been written fixes the UDMA CRC errors on write:
>
> @@ -676,7 +676,8 @@ void ata_sff_exec_command(struct ata_port *ap, const struct
> ata_taskfile *tf)
> DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command);
>
> iowrite8(tf->command, ap->ioaddr.command_addr);
> - ata_sff_pause(ap);
> + ndelay(400);
> +// ata_sff_pause(ap);
> }
> EXPORT_SYMBOL_GPL(ata_sff_exec_command);
>
>
> This rather makes sense. The PDC20247 handles the UDMA part of the
> protocol. It has no way to tell the PDC20246 to wait while it suspends
> UDMA, so that a normal register access can take place - the 246 ploughs
> on with the register access without any regard to the state of the 247.
>
> If the drive immediately starts the UDMA protocol after a write to the
> command register (as it probably will for the DMA WRITE command), then
> we'll be accessing the taskfile in the middle of the UDMA setup, which
> can't be good. It's certainly a violation of the ATA specs.
Fix it by adding custom ->sff_exec_command method for UDMA33 chipsets.
Debugged-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* store UDMA masks in via_isa_bridges[] and while at it make "flags"
field to be u8 instead of u16
* convert the driver to use UDMA masks from via_isa_bridges[]
* remove no longer needed VIA_UDMA* defines
Make some minor documentation and CodingStyle fixes while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Correct via_do_set_mode() documentation while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Timing registers should be programmed with the desired number of clocks
minus one clock.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There shouldn't be any problems with it as IDE cs5535 host driver
has been using those values for years and they match values given
in the (publicly available) datasheet.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
s/ARTIM2/ARTTIM23/ in cmd648_bmdma_stop() while at it
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Clear the primary channel pending interrupt bit
instead of the reserved one.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Account for the requirements of the DMA mode currently used
by the pair device.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use standard cycle timing for CFA PIO5 and PIO6 modes.
Based on commit 74638c8 for IDE subsystem.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Before only the timings for master were set. Datasheet can be found
here: ftp://ftp.vtbridge.org/Docs/Storage/DS_VT6421A_100_CCPL.PDF
Surprisingly, a slave drive works without this patch. According to the
datasheet, the controller by default derives the DMA mode from the
Set Features command issued to a drive. Not sure about the PIO
timings, though. The real problem is that the timings for the master
effectively are the ones tuned for the slave. If these support
different UDMA-settings, there is trouble, especially when the slave
supports a higher UDMA than the master.
Anyhow, using the same mechanism for both master and slave seems like
a good idea.
Signed-off-by: Bart Hartgers <bart.hartgers@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make some variables in ahci and a function in pata_pcmcia static, as found
using sparse.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Traditional IDE interface sucks in that it doesn't have a reliable IRQ
pending bit, so if the controller raises IRQ while the driver is
expecting it not to, the IRQ won't be cleared and eventually the IRQ
line will be killed by interrupt subsystem. Some controllers have
non-standard mechanism to indicate IRQ pending so that this condition
can be detected and worked around.
This patch adds an optional operation ->sff_irq_check() which will be
called for each port from the ata_sff_interrupt() if an unexpected
interrupt is received. If the operation returns %true,
->sff_check_status() and ->sff_irq_clear() will be cleared for the
port. Note that this doesn't mark the interrupt as handled so it
won't prevent IRQ subsystem from killing the IRQ if this mechanism
fails to clear the spurious IRQ.
This patch also implements ->sff_irq_check() for ata_piix. Note that
this adds slight overhead to shared IRQ operation as IRQs which are
destined for other controllers will trigger extra register accesses to
check whether IDE interrupt is pending but this solves rare screaming
IRQ cases and for some curious reason also helps weird BIOS related
glitch on Samsung n130 as reported in bko#14314.
http://bugzilla.kernel.org/show_bug.cgi?id=14314
* piix_base_ops dropped as suggested by Sergei.
* Spurious IRQ detection doesn't kick in anymore if polling qc is in
progress. This provides less protection but some controllers have
possible data corruption issues if the wrong register is accessed
while a command is in progress.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Hans Werner <hwerner4@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
host->ports[i] is never NULL if i < host->n_ports and non-NULL return
from ata_qc_from_tag() guarantees that the returned qc is active.
Drop unnecessary tests.
Superflous () dropped as suggested by Sergei.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Describe UDMA timing bits 18-20 and 21 separately; add a note to bit
31 about it being meaningful for PIO only. Reformat the whole comment,
while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
There's no need to clear the fast interrupt bit in hpt366_set_mode()
since we're doing it in hpt366_init_chipset() already.
While at it, rename 'addr1' local variable to 'addr' and
exclude 'ap->port_no' from its calculation as HPT36x are
single-channel-per-function chips.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
As these drivers' set_piomode() and set_dmamode() methods are almost
identical, factor out the common hpt{37x|3x2n}_set_mode() function
to be called by both of them, the same as in 'pata_hpt366' driver.
This results in ~5% decrease in the 'pata_hpt37x' driver binary
size and in ~4% decrease in the 'pata_hpt3x2n' driver binary size
(as measured on x86-32).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The UltraDMA Tss timing must be stretched with ATA clock of 66 MHz, but the
driver only does this when PCI clock is 66 MHz, whereas it always programs
DPLL clock (which is used as the ATA clock) to 66 MHz.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: <stable@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE registers.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (62 commits)
Input: atkbd - release previously reserved keycodes 248 - 254
Input: add KEY_WPS_BUTTON definition
Input: ads7846 - add regulator support
Input: winbond-cir - fix suspend/resume
Input: gamecon - use pr_err() and friends
Input: gamecon - constify some of the setup structures
Input: gamecon - simplify pad type handling
Input: gamecon - simplify coordinate calculation for PSX
Input: gamecon - fix some formatting issues
Input: gamecon - add rumble support for N64 pads
Input: wacom - add device type to device name string
Input: s3c24xx_ts - report touch only when stylus is down
Input: s3c24xx_ts - re-enable IRQ on resume
Input: wacom - constify product features data
Input: wacom - use per-device instance of wacom_features
Input: sh_keysc - enable building on SH-Mobile ARM
Input: wacom - get features from driver info
Input: rotary-encoder - set gpio direction for each requested gpio
Input: sh_keysc - update the driver with mode 6
Input: sh_keysc - switch to using bitmaps
...
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
These tests already occur elsewhere
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Karol Kozimor <sziwan@users.sourceforge.net>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
No need for clearing ecc_enable_override and checking it in two places.
Instead, simply check it during probing and act accordingly. Also,
rename the flag bitfields according to the functionality they actually
represent. What is more, make sure original BIOS ECC settings are
restored when the module is unloaded.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] wrong attribute of HUB chip written in uv_setup()
[IA64] remove trailing space in messages
[IA64] use asm-generic/scatterlist.h
[IA64] build arch/ia64/kernel/acpi-ext.o when CONFIG_ACPI
[IA64] Only build arch/ia64/kernel/acpi.o when CONFIG_ACPI
[IA64] Remove COMPAT_IA32 support
* 'for-2.6.34' of git://git.kernel.dk/linux-2.6-block: (38 commits)
block: don't access jiffies when initialising io_context
cfq: remove 8 bytes of padding from cfq_rb_root on 64 bit builds
block: fix for "Consolidate phys_segment and hw_segment limits"
cfq-iosched: quantum check tweak
blktrace: perform cleanup after setup error
blkdev: fix merge_bvec_fn return value checks
cfq-iosched: requests "in flight" vs "in driver" clarification
cciss: Fix problem with scatter gather elements in the scsi half of the driver
cciss: eliminate unnecessary pointer use in cciss scsi code
cciss: do not use void pointer for scsi hba data
cciss: factor out scatter gather chain block mapping code
cciss: fix scatter gather chain block dma direction kludge
cciss: simplify scatter gather code
cciss: factor out scatter gather chain block allocation and freeing
cciss: detect bad alignment of scsi commands at build time
cciss: clarify command list padding calculation
cfq-iosched: rethink seeky detection for SSDs
cfq-iosched: rework seeky detection
block: remove padding from io_context on 64bit builds
block: Consolidate phys_segment and hw_segment limits
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (252 commits)
ASoC: Check progress when reporting periods from i.MX FIQ handler
ASoC: Remove a unused variables from i.MX FIQ runtime data
ALSA: hda - Add/fix ALC269 FSC and Quanta models
ALSA: hda - Add ALC670 codec support
OMAP4: PMIC: Add support for twl6030 codec
ALSA: hda - remove unnecessary msleep on power state transitions
usb/gadget/{f_audio,gmidi}.c: follow recent changes in audio.h
ASoC: fsi: Modify over/under run error settlement
ASoC: OMAP4: Add McPDM platform driver
ASoC: OMAP4: Add support for McPDM
ASoC: OMAP: data_type and sync_mode configurable in audio dma
ALSA: hda - Add missing description in HD-Audio-Models.txt
ALSA: add support for Macbook Air 2,1 internal speaker
ALSA: usbaudio: consolidate header files
ALSA: usbmixer: bail out early when parsing audio class v2 descriptors
ALSA: usbaudio: implement basic set of class v2.0 parser
ALSA: usbaudio: introduce new types for audio class v2
ALSA: usbaudio: parse USB descriptors with structs
ALSA: hda - enable snoop for Intel Cougar Point
ALSA: hda - Remove identical definitions for macmini3 model
...
* 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: Protect pid lookup in compat code with RCU
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix documentation of default chip disable()
* 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nvram: Drop the BKL from nvram_open()
Add missing kernel-doc notation for new function parameters:
Warning(drivers/scsi/scsi.c:1031): No description found for parameter 'buf'
Warning(drivers/scsi/scsi.c:1031): No description found for parameter 'buf_len'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A ROM resource that doesn't fit should not cause us to try to re-assign
all the bus resources. Nobody generally cares, and re-assigning is
going to just cause way more troubles than it tries to solve.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some Toshibas only send ACPI events on key down, not key release. Ignore
any release events and send key down and key up events on every ACPI key
down event.
Signed-off-by: Frans Pop <elendil@planet.nl>
Make sure that work is cancelled after removing the i8042 filter, and
unregister the platform device rather than deleting it.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The following build bug (x86, allyesconfig):
arch/x86/oprofile/built-in.o:(.data+0x250): multiple definition of `buffer_mutex'
Was triggered in -tip testing, caused by this upstream commit:
116ee77: dell-laptop: Use buffer with 32-bit physical address
There's multiple buffer_mutex's in the kernel. Make this new one
static.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
radeon was always including the atpx code unnecessarily, also core
switcheroo was including acpi headers.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Type of iterator was promoted to unsigned long in 64bit systems.
*header is small structure so it is alwas safe to cast return value
of sizeof operator to int.
Signed-off-by: Pauli Nieminen <suokkos@gmail.com>
Many new laptops now come with 2 gpus, one to be used for low power
modes and one for gaming/on-ac applications. These GPUs are typically
wired to the laptop panel and VGA ports via a multiplexer unit which
is controlled via ACPI methods.
4 combinations of systems typically exist - with 2 ACPI methods.
Intel/ATI - Lenovo W500/T500 - use ATPX ACPI method
ATI/ATI - some ASUS - use ATPX ACPI Method
Intel/Nvidia - - use _DSM ACPI method
Nvidia/Nvidia - - use _DSM ACPI method.
TODO:
This patch adds support for the ATPX method and initial bits
for the _DSM methods that need to written by someone with
access to the hardware.
Add a proper non-debugfs interface - need to get some proper
testing first.
v2: add power up/down support for both devices
on W500 puts i915/radeon into D3 and cuts power to radeon.
v3: redo probing methods, no DMI list, drm devices call to
register with switcheroo, it tries to find an ATPX method on
any device and once there is two devices + ATPX it inits the
switcher.
v4: ATPX msg handling using buffers - should work on more machines
v5: rearchitect after more mjg59 discussion - move ATPX handling to
radeon driver.
v6: add file headers + initial nouveau bits (to be filled out).
v7: merge delayed switcher code.
v8: avoid suspend/resume of gpu that is off
v9: rearchitect - mjg59 is always right. - move all ATPX code to
radeon, should allow simpler DSM also proper ATRM handling
v10: add ATRM support for radeon BIOS, add mutex to lock vgasr_priv
v11: fix bug in resuming Intel for 2nd time.
v12: start fixing up nvidia code blindly.
v13: blindly guess at finishing nvidia code
v14: remove radeon audio hacks - fix up intel resume more like upstream
v15: clean up printks + remove unnecessary igd/dis pointers
mount debugfs
/sys/kernel/debug/vgaswitcheroo/switch - should exist if ATPX detected
+ 2 cards.
DIS - immediate change to discrete
IGD - immediate change to IGD
DDIS - delayed change to discrete
DIGD - delayed change to IGD
ON - turn on not in use
OFF - turn off not in use
Tested on W500 (Intel/ATI) and T500 (Intel/ATI)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit "disabled" audio on RV710 and RV740 only, leaving RV770 and RV730.
The order is: CHIP_RV770 < CHIP_RV730 < CHIP_RV710 < CHIP_RV740.
It is not needed anway, as we do not even try to enable audio on RV770 and
newer. We call initializing function in r600.c only, not in rv770.c.
If there is something causing green tinges, it's HDMI mode setting for encoder
and I will try to debug that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-testing' of /ssd/git/drm-radeon-next:
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
radeon's have a special ability to passthrough writes in their internal
memory space directly to PCI, this ability means that if some of the internal
surfaces like the depth buffer point at 0x0, any writes to these will
go directly to RAM at 0x0 via PCI busmastering.
Now mesa used to always emit clears after emitting state, since the
radeon mesa driver was refactored a year or more ago, it was found it
could generate a clear request without ever sending any setup state to the
card. So the clear would attempt to clear the depth buffer at 0x0, which
would overwrite main memory at this point. fs corruption ensues.
Also once one app did this correctly, it would never get set back to 0
making this messy to reproduce.
The kernel should block this from happening as mesa runs without privs,
though it does require the user be connected to the current running X session.
This patch implements a check to make sure the depth offset has been set
before a depth clear occurs and if it finds one it prints a warning and
ignores the depth clear request. There is also a mesa fix to avoid sending
the badness going into mesa.
This only affects r100/r200 GPUs in user modesetting mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
rs600 asic was missing set_surface_reg callback leading to
oops.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* anholt/drm-intel-next: (103 commits)
drm/i915: Use a dmi quirk to skip a broken SDVO TV output.
drm/i915: enable/disable LVDS port at DPMS time
drm/i915: check for multiple write domains in pin_and_relocate
drm/i915: clean-up i915_gem_flush_gpu_write_domain
drm/i915: reuse i915_gpu_idle helper
drm/i915: ensure lru ordering of fence_list
drm/i915: extract fence stealing code
drm/i915: fixup active list locking in object_unbind
drm/i915: reuse i915_gem_object_put_fence_reg for fence stealing code
drm/i915: Add dependency on the intel agp module
drm/i915: More s/IS_IRONLAKE/HAS_PCH_SPLIT for Sandybridge.
drm/i915: Correct the Sandybridge chipset info structs.
drm/i915: Disable the hangcheck reset on Sandybridge until we add support.
drm/i915: Add a new mobile Sandybridge PCI ID.
agp/intel: Add a new Sandybridge HB/IG PCI ID combo.
drm/i915, agp/intel: Fix stolen memory size on Sandybridge
drm/i915: Correct locking in the modesetting failure path, fixing a BUG_ON.
drm/i915: Disable the surface tile swizzling on Sandybridge.
agp/intel: Use a non-reserved value for the cache field of the PTEs.
drm/i915: Fix sandybridge status page setup.
...
* nouveau/for-airlied: (25 commits)
drm/nouveau: use ALIGN instead of open coding it
drm/nouveau: report unknown connector state if lid closed
drm/nouveau: support version 0x20 displayport tables
drm/nouveau: Fix noaccel/nofbaccel option descriptions.
drm/nv50: Implement ctxprog/state generation.
drm/nouveau: use dcb connector types throughout the driver
drm/nv50: enable hpd on any connector we know the gpio line for
drm/nouveau: use dcb connector table for creating drm connectors
drm/nouveau: construct a connector table for cards that lack a real one
drm/nouveau: check for known dcb connector types
drm/nouveau: parse dcb gpio/connector tables after encoders
drm/nouveau: reorganise bios header, add dcb connector type enums
drm/nouveau: merge nvbios and nouveau_bios_info
drm/nouveau: merge parsed_dcb and bios_parsed_dcb into dcb_table
drm/nouveau: rename parsed_dcb_gpio to dcb_gpio_table
drm/nouveau: allow retrieval of vbios image from debugfs
drm/nouveau: fix missing spin_unlock in failure path
drm/nouveau: fix i2ctable bounds checking
drm/nouveau: fix nouveau_i2c_find bounds checking
drm/nouveau: fix pramdac_table range checking
...
Conflicts:
drivers/gpu/drm/nouveau/nouveau_gem.c
Just like commit ac5d73fc, we need to be careful to use 'src_cnt' as it
contains the fixed up number of xor sources (forced odd) to meet dmatest's
data verification scheme.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The number of PQ sources specified by module parameter "pq_sources"
is always forced odd to fit into dmatest's destination verificaton
scheme. But number of PQ sources and coefficients as passed to the
driver's prep_dma_pq() is not adjusted accordingly.
Fix it now to get correct PQ testing results in the case passed
"pq_sources" parameter is even.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fsl_dma_update_completed_cookie() appears to calculate the last completed
cookie incorrectly in the corner case where DMA on cookie 1 is in progress
just following a cookie wrap.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
[dan.j.williams@intel.com: fix an integer overflow warning with INT_MAX]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
fsl_dma_tx_submit() only sets the cookie on the first descriptor of a
transaction. It should set the cookie on all.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Acked-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[Resending with the proper subject. Sorry for the mess. ]
This patch is based on the RFC of Stanislaw Gruszka.
More specifically it fixes two possible races:
- One, described by Stanislaw, may lead to permanent disabling of the Tx
queue.
This is fixed by adding the smp_wmb() to propagate the BD consumer
change towards the memory.
- Second may lead to bnx2x_start_xmit() returning NETDEV_TX_BUSY.
This is fixed by taking a tx_lock() before rechecking the number of
available Tx BDs.
thanks,
vlad
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'x86-pci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Enable NMI on all cpus on UV
vgaarb: Add user selectability of the number of GPUS in a system
vgaarb: Fix VGA arbiter to accept PCI domains other than 0
x86, uv: Update UV arch to target Legacy VGA I/O correctly.
pci: Update pci_set_vga_state() to call arch functions
cciss: Fix problem with scatter gather elements in the scsi half of the driver
When support for more than 31 scatter gather elements was added to the block
half of the driver, the SCSI half of the driver was not addressed, and the bump
from 31 to 32 scatter gather elements in the command block itself (not chained)
actually broke the SCSI half of the driver, so that any transfer requiring 32
scatter gather elements wouldn't work. This fix also increases the max transfer
size and size of the scatter gather table to the limit supported by the controller
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: eliminate unnecessary pointer use in cciss scsi code
An extra level of indirection was being used in some places
for no real reason.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: do not use void pointer for scsi hba data
and get rid of related unnecessary type casting
and delete some superfluous and misleading comments nearby.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: factor out scatter gather chain block mapping code
Rationale is I want to use this code from the scsi half of the
driver.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: fix scatter gather chain block dma direction kludge
The data direction for the chained block of scatter gather
elements should always be PCI_DMA_TODEVICE, but was mistakenly
set to the direction of the data transfer, then a kludge to
fix it was added, in which pci_dma_sync_single_for_device or
pci_dma_sync_single_for_cpu was called. If the correct direction
is used in the first place, the kludge isn't needed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: simplify scatter gather code.
Instead of allocating an array of pointers to a structure
containing an SGDescriptor structure, and two other elements
that aren't really used, just allocate SGDescriptor structs.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
cciss: factor out scatter gather chain block allocation and freeing
Rationale is that I want to use this code from the scsi half of the
driver.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Ajay Kumar Gupta