Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. Topcliff PCH has
GPIO I/F. Using this I/F, it is able to access system devices connected
to GPIO.
[akpm@linux-foundation.org: ese DEFINE_PCI_DEVICE_TABLE (per Joe Perches)]
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tomoya MORINAGA <morinaga526@dsn.okisemi.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement irq_chip functionality on ADP5588/5587 GPIO expanders. Only
level sensitive interrupts are supported. Interrupts provided by this
irq_chip must be requested using request_threaded_irq().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for generic 74x164 serial-in/parallel-out 8-bits shift
register. This driver can be used as a GPIO output expander.
[akpm@linux-foundation.org: remove unused local `refresh']
Signed-off-by: Miguel Gaio <miguel.gaio@efixo.com>
Signed-off-by: Juhos Gabor <juhosg@openwrt.org>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The basic GPIO controllers may be found in various on-board FPGA and ASIC
solutions that are used to control board's switches, LEDs, chip-selects,
Ethernet/USB PHY power, etc.
These controllers may not provide any means of pin setup
(in/out/open drain).
The driver supports:
- 8/16/32/64 bits registers;
- GPIO controllers with clear/set registers;
- GPIO controllers with a single "data" register;
- Big endian bits/GPIOs ordering (mostly used on PowerPC).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>,
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the GPIOs on STMPE I/O Expanders.
[l.fu@pengutronix.de: fix set direction input]
[l.fu@pengutronix.de: set GPIO alternate function while requesting]
Acked-by: Luotao Fu <l.fu@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update Kconfig and Makefile in drivers/gpio to discourage inappropriate
addition of platform-specific code.
[akpm@linux-foundation.org: fix tpyo]
Signed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix rdc321x-southbridge build: GPIO_RDC321X needs to select
MFD_CORE so that the core is built at the same (or higher)
tristate level.
rdc321x-southbridge.c:(.devinit.text+0x6103): undefined reference to `mfd_add_devices'
rdc321x-southbridge.c:(.devexit.text+0xe5f): undefined reference to `mfd_remove_devices'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add a GPIO driver to support the GPIOs on the TC35892 I/O Expander.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Janz VMOD-TTL is a MODULbus daughterboard which fits onto any MODULbus
carrier board. It essentially consists of some various logic and a Zilog
Z8536 CIO Counter/Timer and Parallel IO Unit.
The board must be physically configured with jumpers to enable a user to
drive output signals. I am only interested in outputs, so I have made this
driver as simple as possible. It only supports a very minimal subset of the
features provided by the Z8536 chip.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds a new GPIO driver for the RDC321x SoC GPIO controller.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Intel Penwell chip has two 96 pins GPIO blocks, which are very similiar as
Intel Langwell chip GPIO block, except for pin number difference. This
patch expends the original Langwell GPIO driver to support Penwell's.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most of the GPIO expanders supported by the max732x driver have interrupt
generation capability by reporting changes on input pins through an INT#
pin. This patch implements the irq_chip functionnality (edge detection
only).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Jebediah Huang <jebediah.huang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LPC_SCH is selected by GPI_SCH and I2C_ISCH, even when PCI is not
enabled, but LPC_SCH depends on PCI, so make GPI_SCH and I2C_ISCH
also depend on PCI.
Those 2 selects also need to select what LPC_SCH selects,
since kconfig does not follow selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Most of the GPIO expanders controlled by the pca953x driver are able to
report changes on the input pins through an *INT pin.
This patch implements the irq_chip functionality (edge detection only).
The driver has been tested on an Arcom Zeus.
[akpm@linux-foundation.org: the compiler does inlining for us nowadays]
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Nate Case <ncase@xes-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the MAX7300-I2C variant of the MAX7301-SPI version. Both chips share
the same core logic, so the generic part of the in-kernel SPI-driver is
refactored into a generic part. The I2C and SPI specific funtions are
then wrapped into seperate drivers picking up the generic part.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A GPIO driver for the Timberdale FPGA found on the Intel Atom board
Russellville.
The GPIO driver also has an IRQ-chip to support interrupts on the pins.
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With generic modular drivers handling all of this stuff, the
geode-specific code can go away. The cs5535-gpio, cs5535-mfgpt, and
cs5535-clockevt drivers now handle this.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This creates a CS5535/CS5536 GPIO driver which uses a gpio_chip backend
(allowing GPIO users to use the generic GPIO API if desired) while also
allowing architecture-specific users directly (via the cs5535_gpio_*
functions).
Tested on an OLPC machine. Some Leemotes also use CS5536 (with a mips
cpu), which is why this is in drivers/gpio rather than arch/x86.
Currently, it conflicts with older geode GPIO support; once MFGPT support
is reworked to also be more generic, the older geode code will be removed.
Signed-off-by: Andres Salomon <dilinger@collabora.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Cc: David Brownell <david-b@pacbell.net>
Reviewed-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Langwell chip is the IO hub for Intel Moorestown platform which has a
64-pin gpio block device inside. It is exposed as a dedicated PCI device.
We use it to control outside peripheral as well as to do IRQ demuxing.
The gpio block uses MSI to send level type interrupt to IOAPIC.
Signed-off-by: Alek Du <alek.du@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Brownell <david-b@pacbell.net>
Cc: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A GPIO driver for the Freescale MC33880 High/Low side switch
Signed-off-by: Richard Röjfors <richard.rojfors.ext@mocean-labs.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the GPIO pins on the WM831x. No direct support is
currently supplied for configuring non-gpiolib functionality such
as pull configuration and alternate functions, soft configuration
of these will be provided in a future patch.
Currently use of these pins as interrupts is not supported due to
the ongoing issues with generic irq not support interrupt controllers
on interrupt driven buses. Users can directly request the interrupts
with the wm831x-specific APIs currently provided if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is a driver for the ARM PrimeCell PL061 GPIO AMBA peripheral. The
driver is implemented using the gpiolib framework.
This driver also includes support for the use of the PL061 as an interrupt
controller (secondary).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor updates to the pca953x GPIO expander driver: handle several more
compatible parts, and stop assuming that the I2C layer's return codes are
garbage (that's now been fixed).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver supports the Xilinx XPS GPIO IP core which has the typical
GPIO features.
Signed-off-by: Kiran Sutariya <kirans@xilinx.com>
Signed-off-by: John Linn <john.linn@xilinx.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: "Grant Likely" <grant.likely@secretlab.ca>
Cc: <avorontsov@ru.mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds basic support for the GPIOs in the twl4030 power management
chip. That includes two open drain LED drivers, and the use of GPIO-0
(and GPIO-1) as MMC/SD card detect switches which can control whether
the VMMC1 (and VMMC2) regulators are active.
This version of the code has a debounce call that will probably be
replaced before long, when a more generic interface exists.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This adds a driver supporting a family of I2C port expanders from Maxim,
which includes the MAX7319 and MAX7320-7327 chips.
[dbrownell@users.sourceforge.net: minor fixes]
Signed-off-by: Jack Ren <jack.ren@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the bt8xxgpio driver. The purpose of the bt8xxgpio driver is to
export all of the 24 GPIO pins available on Brooktree 8xx chips to the
kernel GPIO infrastructure.
This makes it possible to use a physically modified BT8xx card as
cheap digital GPIO card.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: David Brownell <david-b@pacbell.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a simple sysfs interface for GPIOs.
/sys/class/gpio
/export ... asks the kernel to export a GPIO to userspace
/unexport ... to return a GPIO to the kernel
/gpioN ... for each exported GPIO #N
/value ... always readable, writes fail for input GPIOs
/direction ... r/w as: in, out (default low); write high, low
/gpiochipN ... for each gpiochip; #N is its first GPIO
/base ... (r/o) same as N
/label ... (r/o) descriptive, not necessarily unique
/ngpio ... (r/o) number of GPIOs; numbered N .. N+(ngpio - 1)
GPIOs claimed by kernel code may be exported by its owner using a new
gpio_export() call, which should be most useful for driver debugging.
Such exports may optionally be done without a "direction" attribute.
Userspace may ask to take over a GPIO by writing to a sysfs control file,
helping to cope with incomplete board support or other "one-off"
requirements that don't merit full kernel support:
echo 23 > /sys/class/gpio/export
... will gpio_request(23, "sysfs") and gpio_export(23);
use /sys/class/gpio/gpio-23/direction to (re)configure it,
when that GPIO can be used as both input and output.
echo 23 > /sys/class/gpio/unexport
... will gpio_free(23), when it was exported as above
The extra D-space footprint is a few hundred bytes, except for the sysfs
resources associated with each exported GPIO. The additional I-space
footprint is about two thirds of the current size of gpiolib (!). Since
no /dev node creation is involved, no "udev" support is needed.
Related changes:
* This adds a device pointer to "struct gpio_chip". When GPIO
providers initialize that, sysfs gpio class devices become children of
that device instead of being "virtual" devices.
* The (few) gpio_chip providers which have such a device node have
been updated.
* Some gpio_chip drivers also needed to update their module "owner"
field ... for which missing kerneldoc was added.
* Some gpio_chips don't support input GPIOs. Those GPIOs are now
flagged appropriately when the chip is registered.
Based on previous patches, and discussion both on and off LKML.
A Documentation/ABI/testing/sysfs-gpio update is ready to submit once this
merges to mainline.
[akpm@linux-foundation.org: a few maintenance build fixes]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two small updates to the pcf857x driver: (a) the max732[89] chips are
also second sources for the pcf8574/a, and (b) add a mutex to prevent
trashing the cached state. Adding the lock is effectively a bugfix,
although it seems unlikely that anyone would have run into the issue it
protects against.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maxim's MAX7301 is an SPI GPIO expander with 28 GPIOs. Note: MAX7301's
interrupt feature is not supported yet.
[akpm@linux-foundation.org: coding-style fixes]
[g.liakhovetski@pengutronix.de: Fix inaccuracies in comments, check spi_setup()
return code, mask off high byte in max7301_read()]
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pca953x driver can handle another 8-bit I/O expander, the max7310.
This patch adds that chip to the list of supported IDs in that driver, and
expands the Kconfig helptext accordingly.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This second part of an extension to support more pca953x chips renames the C
and Kconfig symbols. All affected files were updated by sed, except for a
couple of obvious exceptions. It also updates the Kconfig helptext.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a new-style I2C driver with basic support for the sixteen bit
PCA9539 GPIO expanders. These chips have multiple registers, push-pull output
drivers, and (not supported in this patch) pin change interrupts.
Board-specific code must provide "pca9539_platform_data" with each chip's
"i2c_board_info". That provides the GPIO numbers to be used by that chip, and
callbacks for board-specific setup/teardown logic.
Derived from drivers/i2c/chips/pca9539.c (which has no current known users).
This is faster and simpler; it uses 16-bit register access, and cache the
OUTPUT and DIRECTION registers for fast access
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Basic driver for 8-bit SPI based MCP23S08 GPIO expander, without support for
IRQs or the shared chipselect mechanism.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new-style I2C driver for most common 8 and 16 bit I2C based
"quasi-bidirectional" GPIO expanders: pcf8574 or pcf8575, and several
compatible models (mostly faster, supporting I2C at up to 1 MHz).
The driver exposes the GPIO signals using the platform-neutral GPIO
programming interface, so they are easily accessed by other kernel code. The
lack of such a flexible kernel API has been a big factor in the proliferation
of board-specific drivers for these chips... stuff that rarely makes it
upstream since it's so ugly. This driver will let such boards use standard
calls.
Since it's a new-style driver, these devices must be configured as part of
board-specific init. That eliminates the need for error-prone manual
configuration of module parameters, and makes compatibility with legacy
drivers (pcf8574.c, pc8575.c) for these chips easier (there's a clear
either/or disjunction).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders. It will be populated by later patches.
This won't be the only place to hold such gpio_chip code. Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.
This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tomoya MORINAGA