And added a missing kfree to clean up the via_camera struct.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some bridge drivers capture pixels during blanking periods if
pixclk is enabled. In order to avoid capturing bogus data we need to
disable pixclk in the sensor during those blanking periods.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For a frame rate of 30 fps a pixclk of 24MHz is needed. For those
cases where the ov7670 has a clean 24MHz input (xvclk) the PLL
can be bypassed.
This will result in a value of clkrc of 1, which means that in practice
pixclk = xvclk (input clock)
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
According to the datasheet ov7675 uses a formula to achieve
the desired framerate that is different from the operations
done in the current code.
In fact, this formula should apply to ov7670 too. This would
mean that current code is wrong but, in order to preserve
compatibility, the new formula will be used for ov7675 only.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'min_height' and 'min_width' are variables that allow to specify the minimum
resolution that the sensor will achieve. This patch make v4l2 fmt callbacks
consider this parameters in order to return valid data to user space.
Acked-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ov7675 and ov7670 share the same registers but there is no way
to distinguish them at runtime. However, they require different
tweaks to achieve the desired resolution. For this reason this
patch adds a new ov7675 entry to the ov7670_id table.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If more than 127 different lengths are transmitted then the driver causes
an overrun on sample_lens. Try to send as much as possible and return the
amount sent.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This transceiver expects the set IR TX ports and IR data as seperate
packets, like the Windows driver does. Remove unnecessary kzalloc.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The GET_REVISION command puts the device in an unresponsive state,
although it continues to report any IR activity. Note that GET_REVISION
command is not documented, nor is any possible response to it parsed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- move the bit shifting of width+height values inside the function
- fix the debug message format and output values
- add comment about the size limit (e.g. EM277x supports >2MPix)
- make void, because error checking is incomplete and we never check the
returned value (we would continue anyway)
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All drivers which use this subdevice use also the control framework.
The v4l2_subdev_core_ops operations {query/g_/s_}ctrl are useless because
device drivers will inherit controls from this subdevice.
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch re-write the driver and use the videobuf2
interface instead of the old videobuf. Moreover, it uses also
the control framework which allows the driver to inherit
controls from its subdevice (ADV7180). Finally the driver does not
implement custom file operation but it uses the generic ones from
videobuf2 and v4l2_fh
Signed-off-by: Federico Vaga <federico.vaga@gmail.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The buffer ioctls (VIDIOC_REQBUFS, VIDIOC_QUERYBUF, VIDIOC_QBUF, VIDIOC_DQBUF,
VIDIOC_EXPBUF, VIDIOC_CREATE_BUFS, VIDIOC_PREPARE_BUF) are not applicable for
radio devices. Hence, they should be set valid only for non-radio devices in
determine_valid_ioctls().
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Clear the proper array when deregistering FIMC-LITE devices. Now
fimc[] array is erroneously accessed instead of fimc_lite[] and
fimc_md_unregister_entities() function call can result in an oops
from NULL pointer dereference, since fmd->fimc[] is cleared earlier.
This might happen in normal conditions when the driver's probing
is deferred and then retried.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In some circumstances after issuing the V4L2_ENC_CMD_STOP the application
could freeze. This patch prevents this behavior.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move e_clkput label after the clk_disable() call so a not acquired clock
is not attempted to be disabled. This fixes runtime warnings like:
s5p-mipi-csis 11880000.csis: failed to get clock: sclk_csis
------------[ cut here ]------------
WARNING: at drivers/clk/clk.c:478 clk_disable+0x24/0x34()
Modules linked in:
[<c001603c>] (unwind_backtrace+0x0/0x13c) from [<c0022060>] (warn_slowpath_common+0x54/0x64)
[<c0022060>] (warn_slowpath_common+0x54/0x64) from [<c002208c>] (warn_slowpath_null+0x1c/0x24)
[<c002208c>] (warn_slowpath_null+0x1c/0x24) from [<c033f868>] (clk_disable+0x24/0x34)
[<c033f868>] (clk_disable+0x24/0x34) from [<c02feff8>] (s5pcsis_probe+0x25c/0x4c8)
[<c02feff8>] (s5pcsis_probe+0x25c/0x4c8) from [<c0268e34>] (platform_drv_probe+0x18/0x1c)
[<c0268e34>] (platform_drv_probe+0x18/0x1c) from [<c0267700>] (driver_probe_device+0xa4/0x368)
[<c0267700>] (driver_probe_device+0xa4/0x368) from [<c0267a50>] (__driver_attach+0x8c/0x90)
[<c0267a50>] (__driver_attach+0x8c/0x90) from [<c0265c94>] (bus_for_each_dev+0x60/0x8c)
[<c0265c94>] (bus_for_each_dev+0x60/0x8c) from [<c02665e8>] (bus_add_driver+0x20c/0x2d4)
[<c02665e8>] (bus_add_driver+0x20c/0x2d4) from [<c0268064>] (driver_register+0x78/0x194)
[<c0268064>] (driver_register+0x78/0x194) from [<c0008668>] (do_one_initcall+0x34/0x188)
[<c0008668>] (do_one_initcall+0x34/0x188) from [<c03de57c>] (kernel_init+0x180/0x2f0)
[<c03de57c>] (kernel_init+0x180/0x2f0) from [<c000f0d8>] (ret_from_fork+0x14/0x3c)
---[ end trace 0c5a55345c42530b ]---
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those optional operations are used to release and reacquire the queue
lock when videobuf2 needs to perform operations that sleep for a long
time, such as waiting for a buffer to be complete. Implement them to
avoid blocking qbuf or streamoff calls when a dqbuf is in progress.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces the use of IS_ENABLED() macro. For example,
replacing:
#if defined(CONFIG_I2C) || (defined(CONFIG_I2C_MODULE) && defined(MODULE))
with:
#if IS_ENABLED(CONFIG_I2C)
All changes made by this patch respect the same replacement pattern.
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark current frame as error frame when ppi error interrupt
report fifo error. Member next_frm in struct bcap_device can
be optimized out.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for Digivox Mini HD (rtl2832)
The tuner works, but with worst performance then realtek linux driver,
due to incomplete implementation of fc2580.c
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
Tested-by: Lorenzo Dongarrà <lorenzo_64@katamail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a missing break so we use XC_RF_MODE_CABLE instead of
XC_RF_MODE_AIR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove em28xx_i2c_ir_work() and check the device type in the common callback
function em28xx_ir_work() instead. Simplifies em28xx_ir_start().
Reduces the code size with a minor performance drawback.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set up the i2c_client locally in em28xx_i2c_ir_handle_key().
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We already have the key polling functions and the polling infrastructure in
em28xx-input, so we can easily get rid of the dependency on module ir-kbd-i2c.
For maximum safety, do not touch the key reporting mechanism for those devices.
Code size could be improved further but would have minor peformance impacts.
Tested with device "Terratec Cinergy 200 USB" (EM2800_BOARD_TERRATEC_CINERGY_200)
[mchehab@redhat.com: Fix two checkpatch.pl warnings:
ERROR: "foo * bar" should be "foo *bar" (line 465)
WARNING: kfree(NULL) is safe this check is probably not required (line 725)]
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We don't report any key/scan codes or errors inside the key polling functions
for internal IR RC devices, just in the key handling fucntions.
Do the same for external devices.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Field 'old' of struct IR_i2c is used nowhere in module ir-kbd-i2c.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My static checker complains about the fall through here. From the
context it looks like we should add a break statement.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media fixes from Mauro Carvalho Chehab:
"For a regression fix on a few radio drivers that were preventing radio
TX to work on those devices"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] radio: set vfl_dir correctly to fix modulator regression
Change several memcpy() to memmove() in cases when the regions are
definitely overlapping; memcpy() of overlapping regions is undefined
behavior in C and can produce different results depending on the compiler,
the memcpy implementation, etc.
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The idx values passed to cx18_i2c_register() and ivtv_i2c_register()
by cx18_init_subdevs() and ivtv_load_and_init_modules() respectively
are always in-range, based on how the hw_all bitmask is populated.
Previously, the checks were already ineffective because arrays were
being dereferenced using the index before the check.
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix bug introduced in 7757ddda6f, where
instead of bit-negating the bitmask, the bit position was bit-negated
instead.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Cc: Olivier Grenie <olivier.grenie@dibcom.fr>
Cc: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On cold boot the device does not initialize until the first packet is
received, and that packet is not processed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A sample resolution of 2us generates more than 300 interrupts per key
and this resolution is not needed unless carrier reports are enabled.
Revert to a resolution of 10us unless carrier reports are needed. This
generates up to a fifth of the interrupts.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current code was implemented with some default configurations,
this default configuration works on board and doesn't work on other.
This patch accepts the configuration through platform data and configures
the encoder depending on the data passed.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two fixes:
- the priv field wasn't set to 0.
- only V4L2_FIELD_INTERLACED is supported.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- add device_caps support
- fix bus_info
- fix numerous tuner-related problems due to incorrect tests
and setting v4l2_tuner fields to wrong values.
- remove (audio) input support from the radio: it doesn't belong
there. This also fixed a nasty issue where opening the radio
would set dev->input to 5 for no good reason. This was never
set back to a valid TV input after closing the radio device,
thus leaving it at 5 which is out of bounds of the vinput
card array.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the meye driver to the control framework. Some private controls
have been replaced with standardized controls (SHARPNESS and JPEGQUAL).
The AGC control looks like it can be replaced by the AUTOGAIN control, but
it isn't a boolean so I do not know how to interpret it.
The FRAMERATE control looks like it can be replaced by S_PARM, but again,
without knowing how to interpret it I decided to leave it alone.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you only poll for events, then vb2_poll will return POLLPRI | POLLERR if
no streaming is in progress. That's not right, it's perfectly valid to
poll just for events.
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I know, nobody really cares about this black-and-white webcam anymore, but
it was fun to do.
Tested with an actual webcam.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a v4l2-compliance problem: the priv field of v4l2_pix_format must be
cleared by drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- instead of a mute module option, use audmode as per the spec.
- clamp the frequency before setting it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Such ioctls are not valid for radio devices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Don't set version (done by the v4l2 core), fill in bus_info, set correct
driver name and add device_caps support.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The inputmask for the tea6420 wasn't set and the wrong mute register value
was used.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The balance control did not do what it is supposed to do due to wrong
calculations.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Newer Exynos4 SoC are equipped with a local camera ISP that
controls external raw image sensor directly. Such sensors
can be connected through FIMC-LITEn (and MIPI-CSISn) IPs to
the ISP, which then feeds image data to the FIMCn IP. Thus
there can be two busses associated with an image source
(sensor). Rename struct s5p_fimc_isp_info describing external
image sensor (video decoder) to struct fimc_source_info to
avoid confusion. bus_type is split into fimc_bus_type and
sensor_bus_type. The bus type enumeration is extended to
include both FIMC Writeback input types.
The bus_type enumeration and the data structure name in the
board files are modified according to the above changes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add clk_prepare(), clk_unprepare() calls for the sclk_cam clocks
to ensure the driver works on platforms with the common clocks
API enabled.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The V4L2_SEL_TGT_CROP_BOUNDS, V4L2_SEL_TGT_COMPOSE_BOUNDS selection
targets are not supposed to be handled in the set_selection ioctl.
Remove the code that doesn't do anything sensible now and make sure
ctx->state is modified with the spinlock held.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure a valid image format is initially set on both the CAPTURE
and the OUTPUT buffer queue.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With presence of some faults, e.g. caused by wrong platform data or
the device tree structure the IDX_SENSOR entry in the array may be NULL,
so make sure it is not dereferenced then.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following sparse warnings:
drivers/media/i2c/s5c73m3/s5c73m3-core.c:42:5: warning:
symbol 'boot_from_rom' was not declared. Should it be static?
drivers/media/i2c/s5c73m3/s5c73m3-core.c:45:5: warning:
symbol 'update_fw' was not declared. Should it be static?
drivers/media/i2c/s5c73m3/s5c73m3-core.c:298:5: warning:
symbol 's5c73m3_isp_comm_result' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
clk_set_rate(), clk_enable() functions can fail, so check the return
values to avoid surprises. While at it use ERR_PTR() value to indicate
an invalid clock.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous method of registering platform entities into the main
driver using driver_find() and then iterating over devices bound to
a driver was racy and is being removed here. Nothing was preventing
module from unloading during a call to try_module_get(driver->owner).
Instead, we look up a device first and then check for its driver while
holding device lock.
The platform sub-devices are looked up and registered to the top
level driver. When any sub-device is not yet initialized and ready
the main driver's probe() will be deferred.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes regression introduced in commit 6319d6a002beb26631
'[media] fimc-lite: Add ISP FIFO output support'.
In case of a configuration where video is captured at the video node
exposed by the FIMC-LITE driver there is a following video pipeline:
sensor -> MIPI-CSIS.n -> FIMC-LITE.n subdev -> FIMC-LITE.n video node
In this situation s_stream() handler of the FIMC-LITE.n is called
back from within VIDIOC_STREAMON/OFF ioctl of the FIMC-LITE.n video
node, through vb2_stream_on/off(), start/stop_streaming and
fimc_pipeline_call(set_stream). The fimc->lock mutex is already held
then, before invoking vidioc_streamon/off. So it must not be taken
again in the s_stream() callback in this case, to avoid a deadlock.
This patch makes fimc->out_path atomic_t so the mutex don't need
to be taken in the FIMC-LITE subdev s_stream() callback in the DMA
output case.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyugmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The .s_power FIMC-LITE subdev callback is now empty and
unneeded. The FIMC-LITE IP power handling will be done
by the FIMC-IS driver, so just remove the callback.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add driver for S5C73M3 image sensor. The driver exposes the sensor as
two subdevs: pure sensor and output interface. Two subdev architecture
supports interleaved UYVY/JPEG image format with separate frame size
for both sub-formats, there is a spearate pad for each sub-format.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleaned up the memory devices allocation code and added
missing device_initialize() call to remove the kernel warning
during memory allocations.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use WARN_ON(condition) directly instead of wrapping around an if
condition.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All host drivers using this subdev driver are already converted
to use the control framework so the compatibility ops can be dropped.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modified the G2D driver (which initially supported only H/W Rev.3)
to support H/W Rev.4.1 present on Exynos4x12 and Exynos52x0 SOCs.
- Set the SRC and DST type to 'memory' instead of using reset values.
- FIMG2D v4.1 H/W uses different logic for stretching(scaling).
- Use CACHECTL_REG only with FIMG2D v3.
[s.nawrocki: removed empty line at end of file]]
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure bytesperline for Cb, Cr planes for V4L2_PIX_FMT_YUV420M
format is half of the Y plane value, rather than having same
bytesperline for all planes.
While at it, simplify the bytesperline parameter handling by
storing it when image format is set and returning those values
when getting the format, instead of recalculating bytesperline
from intermediate parameters.
Reported-by: Sebastian Dröge <sebastian.droege@collabora.co.uk>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed wrong condition in firmware reload function used by the watchdog.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes a v4l2-compliance error: setting audmode to a value other than mono
or stereo for a radio device should map to MODE_STEREO.
The spec specifies that for radio devices only mono and stereo audmodes are
valid. If the user specifies another audmode in v4l2_tuner, then that should
be mapped to valid audmode. That didn't happen here.
Note that tuner drivers might decide to limit the possible audmode even
further if it only supports mono. In that case the tuner driver can set
audmode to mono. However, that new value wasn't copied back to t->audmode,
and that has been fixed as well in this patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2 sub-device driver for OV9650/OV9652 image sensors.
The driver exposes following V4L2 controls:
- auto/manual exposure,
- auto/manual white balance,
- auto/manual gain,
- brightness, saturation, sharpness,
- horizontal/vertical flip,
- color bar test pattern,
- banding filter (power line frequency).
Frame rate can be configured with g/s_frame_interval pad level ops.
Supported resolution are only: SXGA, VGA, QVGA.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a v4l2 core helper function that can be used as
the log_status handler for subdevs that only need to log state
of the v4l2 controls owned by the subdev's control handler.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a v4l2 core helper function that can be used as the subdev
.subscribe_event handler. This allows to eliminate some boilerplate
from drivers that are only handling the control events.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
