Cleanup hint: Some features are calculated in tg3_get_invariants() and
the rest in its caller --- tg3_init_one(). This is not changed here.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement control of LED via set_phys_id.
Note: since PHY is powered off if device is down, this board
only allows blinking if device is up.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a 5717 or 5719 NVRAM part is manually strapped and is 2mb in size,
the driver needs to look at the NVRAM size field rather than infer it
from the strapping itself.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5720 device ID to the PCI table, thus enabling 5720
support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5720 PHY ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the new Host to BMC feature.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5720 implements its own NVRAM pin strapping scheme. This patch adds
the required support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the 5720 ASIC rev.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reintroduces the TG3_FLG3_5717_PLUS to identify 5717 and
later devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 57765 arrived before the 5717 and has a subset of the features
supported by the 5717. This patch renames the 5717_PLUS flag so that it
can be reintroduced to designate only 5717 and later devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardcoded values are used in multiple places to describe the maximum rx
ring sizes. This patch replaces those values with preprocessor
constants. This patch also introduces a new TG3_FLG3_LRG_PROD_RING_CAP
to determine if the device is capable of supporting larger ring sizes.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IRQF_SAMPLE_RANDOM flag is marked as deprecated and will be removed.
Every input point to the kernel's entropy pool have to better document the
type of entropy source it is.
drivers/char/random.c now implements a set of interfaces that can be used for
devices to collect enviromental noise. IRQF_SAMPLE_RANDOM will be replaced
with these add_*_randomness exported functions.
Network drivers are not a good source of entropy. They use as a source of
entropy essentially a remote host. Which means that the source of entropy can
be potentially controlled by an attacker. Also, with heavy workloads the
entropy decreases due to less hardware interrupts happening thanks to irq
mitigation and NAPI.
If a system relies in its network interface as a entropy source it has a false
sense of security. Systems that don't have devices whose drivers are good
sources of entropy, should either use a hardware random number generator or
feed the kernel's entropy pool from userspace using other sources of entropy
such as EGD, video_entropyd, timer_entropyd and audio-entropyd.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct usage is "static inline void" not "static void inline".
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is proper style to include linux/foo.h instead asm/foo.h if both exist
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5750 ASIC rev was never released as a PCI device. It only exists as
a PCIe device. This patch removes the code that supports the former
configuration.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the function that initializes the link configuration
closer to the place where the rest of the phy code is initialized.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the near future, the VAux switching decision process is going to get
more complicated. This patch refines and consolidates the existing
algorithm in anticipation of the new scheme.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 895950c2a6, entitled
"tg3: Use DEFINE_PCI_DEVICE_TABLE" moved two pci device tables into the
global address space, but didn't declare them static and didn't prefix
them with "tg3_". This patch fixes those problems.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to verify the checksum stored in the "RV" info
keyword of the RODATA VPD section.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 NVRAM selftest actually fails when validating the checksum of
the legacy NVRAM format. However, the test still reported success
because the last update of the return code was a success from the NVRAM
reads. This patch fixes the code so that the error return code defaults
to a failure status. Then the patch fixes the reason why the checsum
validation failed.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2866d956fe, entitled
"tg3: Expand 5719 workaround" extended a 5719 A0 workaround to all
revisions of the chip. There was a change that should have been a
part of that patch that was missed. This patch adds the missing
piece.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver uses device_init_wakeup() in such a way that the
device's power.can_wakeup flag may be set even though the PCI
subsystem cleared it before, in which case the device cannot wake
up the system from sleep states. Modify the driver to only change
the power.can_wakeup flag if the device is not capable of generating
wakeup signals.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a precautionary measure, expand the fix submitted in commit
4d163b75e9 entitled "tg3: Fix 5719 A0 tx
completion bug" to apply to all 5719 revisions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates copyrights and updates the tg3 version to 3.117.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a preprocessor naming bug for one of the EEE registers.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where EEE will fail to work in certain
environments.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE interferes with the hardware's ability to loop a packet back to the
host. This patch disables the feature for the duration of the test.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On CPMU devices, the MAC loopback test does not test any important paths
the phy loopback test doesn't also test. The phy loopback test is the
more comprehensive test. This patch disables the MAC loopback test for
these devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The half-duplex bit in the MAC MODE register will be set during the
loopback test if the external link is in half-duplex mode. This will
cause the loopback test to fail on newer devices. This patch turns the
half-duplex bit off for the test.
Also, newer devices fail the internal phy loopback test because the phy
link takes a little while to come up. This patch adds code to wait for
the link before proceeding with the test.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If management firmware is present and the device is down, the firmware
will assume control of the phy. If a phy access were allowed from the
host, it will collide with firmware phy accesses, resulting in
unpredictable behavior. This patch fixes the problem by disallowing phy
accesses during the problematic condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For single vector MSI-X allocations, we do not want to enable
multivector modes. This patch makes the necessary corrections.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pivots the tg3 driver to the new VLAN infrastructure.
All references to vlgrp have been removed. The driver still attempts to
disable VLAN tag stripping if CONFIG_VLAN_8021Q or
CONFIG_VLAN_8021Q_MODULE is not defined.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5719 A0 has a bug that manifests itself as if the chipset were
reordering memory writes. The best known way to solve this problem is
to turn off LSO and jumbo frames.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit cf79003d59, entitled
"tg3: Fix 5719 internal FIFO overflow problem", proposed a way to solve
an internal FIFO overflow problem. We have since discovered a slightly
better way to solve the problem. This patch changes the code so that
the problem is contained closer to the problem source.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case CONFIG_PM_SLEEP is disabled, we dont need tg3_suspend() and
tg3_resume().
drivers/net/tg3.c:15056: warning: ‘tg3_suspend’ defined but not used
drivers/net/tg3.c:15110: warning: ‘tg3_resume’ defined but not used
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Besides -ETIMEDOUT and -EINTR, pci_read_vpd may return other error
values like -ENODEV or -EINVAL which are ignored due to the buggy
check, but the data are not read from VPD anyway and this is checked
subsequently with at most 3 needless loop iterations. This does not
show up as a runtime bug.
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver uses the legacy PCI power management, so it has to do
some PCI-specific things in its ->suspend() and ->resume() callbacks,
which isn't necessary and should better be done by the PCI
sybsystem-level power management code.
Convert tg3 to the new PCI power management framework and make it
let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.
Tested on HP nx6325 with a NetXtreme BCM5788 adapter.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_scheduled_work() is on its way out. This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.
Directly cancel the used works on driver detach and flush them in
other cases.
The conversions are mostly straight forward and the only dangers are,
* Forgetting to cancel/flush one or more used works.
* Cancelling when a work should be flushed (ie. the work must be
executed once scheduled whether the driver is detaching or not).
I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org
This patch updates the tg3 version to 3.116.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware defaults to fairly aggressive EEE thresholds. While there
appear to be no ill effects, this patch relaxes them, just as a
precaution.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first hunk of this patch makes sure that the driver checks for the
appropriate preconditions before checking if EEE negotiation succeeded.
More specifically the link needs to be full duplex for EEE to be
enabled.
The second and third hunks of this patch fix a bug where the eee
advertisement register would be programmed with extra bits set.
The fourth hunk of this patch makes sure the EEE capability flag is not
set for 5718 A0 devices and that the device is not a serdes device.
None of these modifications are strictly necessary. The driver /
hardware still does the right thing. They are submitted primarily for
correctness.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE support in the 57765 internal phy will not enable after a phy reset
unless it sees that EEE is supported in the MAC. This patch moves the
code that programs the CPMU EEE registers to a place before the phy
reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 52b02d04c8 entitled "tg3: Add
EEE support", Ben Hutchings had commented that the EEE advertisement
register will be in a standard location. This patch moves that
definition into mdio.h and changes the code to use it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current transmit routines set the jumbo frame BD flag too
aggressively. This can reduce performance for common cases. This patch
raises the jumbo flag threshold to 1518, up from 1500.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the gphy autopowerdown feature in the phy for all
new devices that support it.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dma_alloc_coherent() permits to use GFP_KERNEL allocations instead
of GFP_ATOMIC ones. Its better when a machine is out of memory, because
this allows driver to sleep to get its memory and succeed its init,
especially when allocating high order pages.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All TSS bugs have been fixed in the 5719. This patch reenables the
feature.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The multiple DMA read engine bugs have been fixed on the 5719. This
patch reenables support for this feature.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
