We only manipulate the must_dispatch and queue_new flags, they are not
tested anymore. So get rid of them.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The IO scheduler core calls into the IO scheduler dispatch_request hook
to move requests from the IO scheduler and into the driver dispatch
list. It only does so when the dispatch list is empty. CFQ moves several
requests to the dispatch list, which can cause higher latencies if we
suddenly have to switch to some important sync IO. Change the logic to
move one request at the time instead.
This should almost be functionally equivalent to what we did before,
except that we now honor 'quantum' as the maximum queue depth at the
device side from any single cfqq. If there's just a single active
cfqq, we allow up to 4 times the normal quantum.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This driver supports mflash IO mode for linux.
Mflash is embedded flash drive and mainly targeted mobile and consumer
electronic devices.
Internally, mflash has nand flash and other hardware logics and supports 2
different operation (ATA, IO) modes. ATA mode doesn't need any new driver
and currently works well under standard IDE subsystem. Actually it's one
chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.
Followings are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.
This driver is quitely similar to a standard ATA driver, but because of
following reasons it is currently seperated with ATA layer.
1. ATA layer deals standard ATA protocol. ATA layer have many low-
level device specific interface, but data transfer keeps ATA rule.
But, mflash IO mode doesn't.
2. Even though currently not used in mflash driver code, mflash has
some custom command and modes. (nand fusing, firmware patch, etc) If
this feature supported in linux kernel, ATA layer more altered.
3. Currently PATA platform device driver doesn't support interrupt.
(I'm not sure) But, mflash uses interrupt (polling mode is just for
debug).
4. mflash is somewhat under-develop product. Even though some company
already using mflash their own product, I think more time is needed for
standardization of custom command and mode. That time (maybe October)
I will talk to with ATA people. If they accept integration, I will
integrate.
Signed-off-by: unsik Kim <donari75@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Add a method for discovering the first memory BAR. All Smart Array
controllers to date have always had the the memory BAR as the first BAR.
A new controller to be released later this year breaks that model.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The MSA2012 cannot inform the driver of configuration changes since all
management is out of band. This is a departure from any storage we have
supported in the past. We need some way to detect changes on the topology
so we implement this kernel thread. In some instances there's nothing we
can do from the driver (like LUN failure) so just print out a message. In
the case where logical volumes are added or deleted we call
rebuild_lun_table to refresh the driver's view of the world.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We must complete the full request, so store the request count and then set
the ->data_len to the residual count from the hardware.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This forces in_flight to be zero when turning off or on the I/O stat
accounting and stops updating I/O stats in attempt_merge() when
accounting is turned off.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Simple helper functions to quiesce the request queue. These are
currently only used for switching IO schedulers on-the-fly, but
we can use them to properly switch IO accounting on and off as well.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Since TOMOYO's policy management tools does not use the "undelete domain"
command, we decided to remove that command.
Signed-off-by: Kentaro Takeda <takedakn@nttdata.co.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Toshiharu Harada <haradats@nttdata.co.jp>
Signed-off-by: James Morris <jmorris@namei.org>
This fixes a problem reported by Sean MacLennan where loading any
module would cause an oops. We weren't marking the pages containing
the module text as having hardware execute permission, due to a bug
introduced in commit 8d1cf34e ("powerpc/mm: Tweak PTE bit combination
definitions"), hence trying to execute the module text caused an
exception on processors that support hardware execute permission.
This adds _PAGE_HWEXEC to the definitions of PAGE_KERNEL_X and
PAGE_KERNEL_ROX to fix this problem.
Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[paulus@samba.org: changed to use syscall numbers 320 and 321 since
perf_counters is currently using 319.]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
'tramp' is an unsigned long, so print it with %lx.
Fixes the following build warning:
arch/powerpc/kernel/ftrace.c:291: error: format ‘%x’ expects type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit bb7253403f ("powerpc64,
ftrace: save toc only on modules for function graph"), added an
#if CONFIG_PPC64. This changes it to #ifdef.
Fixes the following warning on 32-bit builds:
arch/powerpc/kernel/ftrace.c:562:5: error: "CONFIG_PPC64" is not defined
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ptrace compat wrapper mishandles access to the fpu registers. The
PTRACE_PEEKUSR and PTRACE_POKEUSR requests miscalculate the index into
the fpr array due to the broken FPINDEX macro. The
PPC_PTRACE_PEEKUSR_3264 request needs to use the same formula that the
native ptrace interface uses when operating on the register number (as
opposed to the 4-byte offset). The PPC_PTRACE_POKEUSR_3264 request
didn't take TS_FPRWIDTH into account.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The irq remapping layer seems to cause some confusion when people
see a different irq number in /proc/interrupts vs the one they
request in their driver or DTS.
So have the irq remapping layer print out a message when we map an
irq. The message is only printed the first time the irq is mapped,
and it's KERN_DEBUG so most people won't see it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
commit 28794d34ec ("powerpc/kconfig: Kill
PPC_MULTIPLATFORM") broke KEXEC, by making it dependent on BOOK3S, while it
should be PPC_BOOK3S.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When we call giveup_fpu, we need to need to turn off VSX for the
current process. If we don't, on return to userspace it may execute a
VSX instruction before the next FP instruction, and not have its
register state refreshed correctly from the thread_struct. Ditto for
altivec.
This caused a bug where an unaligned lfs or stfs results in
fix_alignment calling giveup_fpu so it can use the FPRs (in order to
do a single <-> double conversion), and then returning to userspace
with FP off but VSX on. Then if a VSX instruction is executed, before
another FP instruction, it will proceed without another exception and
hence have the incorrect register state for VSX registers 0-31.
lfs unaligned <- alignment exception turns FP off but leaves VSX on
VSX instruction <- no exception since VSX on, hence we get the
wrong VSX register values for VSX registers 0-31,
which overlap the FPRs.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable relay in pseries config, ppc64_defconfig had it enabled but pseries
did not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Instead of checking for known events, pass in all 1s so we handle future
event types. We were currently missing the IO event type.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PHYP tells us how often a shared processor dispatch changed physical cpus.
This can highlight performance problems caused by the hypervisor.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make all messages consistent, some have spaces before the "...", some do not.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ibm,client-architecture method will often cause a reconfiguration reboot.
When this happens the last thing we see is:
Hypertas detected, assuming LPAR !
Which doesn't explain what just happened. Wrap the ibm,client-architecture
so it's clear what is going on:
Calling ibm,client-architecture... done
In order to maintain the law of conservation of screen real estate, downgrade
two other messages to debug.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The (relatively) new pmac_zilog driver doesn't use the pre-munged
IRQ numbers from the macio_dev unlike other macio things, it
directly maps it off the OF device-tree.
It does that because it can be initialized much earlier than the
registration of the macio devices, in order to get a serial
console early.
Unfortunately, that means that it "misses" some fixups done
by the macio layer to work around missing interrupt descriptions
in the device-tree of the Wallstreet machines.
This patch brings the necessary workaround into the pmac_zilog
driver itself to bring it back to working condition.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The buffer passed to the ibm,get-system-parameter RTAS call must be
in the RMA. To ensure we pass an address in the RMA use rtas_data_buf
for the actual RTAS call and then copy the result to value. We can't
just make it static because this can be compiled in as a module.
Also add the WDRTAS_SP_SPI_LEN so we don't litter '4' throughout the
function.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Tested-by: Adrian Reber <adrian@lisas.de>
Acked-by: Utz Bacher <utz.bacher@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add powerdown sequence for VREF using a shared jack when the headphone
is present and the microphone isn't on.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added an else part to check
SNDRV_MIXER_OSS_PRESENT_CVOLUME for MIC (slot 7)
in commit 36c7b833e5
Similarly, checks and volume control is required for
SNDRV_MIXER_OSS_PRESENT_CSWITCH and SNDRV_MIXER_OSS_PRESENT_CROUTE
as well.
Signed-off-by: Deepika Makhija <deepika.makhija@einfochips.com>
Signed-off-by: Viral Mehta <viral.mehta@einfochips.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To enable periods shorter than 1 ms, we have to make sure that short
periods are only available for alternate settings that have a small
enough data packet interval. Furthermore, the code that aligns URBs to
USB frames is now superfluous.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The data packet interval needs to be available in the audioformat
structure, together with the other audio format parameters, so that it
can be used to influence ALSA hardware parameters.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This removes the check_hw_params_convention() function because
1) it is not necessary, as the hw_rule_* functions also work correctly
(i.e., as no-ops) when the device supports all combinations of the
audio format parameters; and
2) it would become too complex when adding a fourth altsetting-dependent
hardware parameter, as this would require another three loops to
check dependecies with rate/channels/format.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When listing the device's sample formats in the stream? proc file, the
sample format number itself is rather obscure, so we better show the
format width, too.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
b44: Use kernel DMA addresses for the kernel DMA API
forcedeth: Fix resume from hibernation regression.
xfrm: fix fragmentation on inter family tunnels
ibm_newemac: Fix dangerous struct assumption
gigaset: documentation update
gigaset: in file ops, check for device disconnect before anything else
bas_gigaset: use tasklet_hi_schedule for timing critical tasklets
net/802/fddi.c: add MODULE_LICENSE
smsc911x: remove unused #include <linux/version.h>
axnet_cs: fix phy_id detection for bogus Asix chip.
bnx2: Use request_firmware()
b44: Fix sizes passed to b44_sync_dma_desc_for_{device,cpu}()
socket: use percpu_add() while updating sockets_in_use
virtio_net: Set the mac config only when VIRITO_NET_F_MAC
myri_sbus: use request_firmware
e1000: fix loss of multicast packets
vxge: should include tcp.h
Conflict in firmware/WHENCE (SCSI vs net firmware)
We must not use the device DMA addresses for the kernel DMA API, because
device DMA addresses have an additional offset added for the SSB translation.
Use the original dma_addr_t for the sync operation.
Cc: stable@kernel.org
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset phy state on resume, fixing a regression caused by powering down
the phy on hibernate.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The client_register and client_unregister methods are optional so
there is no point in defining stub ones. Especially when these methods
are likely to be removed soon.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jens Axboe