Commit graph

666 commits

Author SHA1 Message Date
Henrik Rydberg
8c9398d1e9 hwmon: applesmc: lighter wait mechanism, drastic improvement
The read fail ratio is sensitive to the delay between the first byte
written and the first byte read; apparently the sensors cannot be rushed.
Increasing the minimum wait time, without changing the total wait time,
improves the fail ratio from a 8% chance that any of the sensors fails in
one read, down to 0.4%, on a Macbook Air.  On a Macbook Pro 3,1, the
effect is even more apparent.  By reducing the number of status polls, the
ratio is further improved to below 0.1%.  Finally, increasing the total
wait time brings the fail ratio down to virtually zero.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Tested-by: Bob McElrath <bob@mcelrath.org>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Henrik Rydberg
07e8dbd3eb hwmon: applesmc: Add support for Macbook Pro 3
Add temperature sensor support for Macbook Pro 3.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Henrik Rydberg
d7549905f1 hwmon: applesmc: Add support for Macbook Pro 4
Adds temperature sensor support for the Macbook Pro 4.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Andrew Morton
7b5e3cb28f drivers/hwmon/applesmc.c: remove unneeded casts
dmi_system_id.driver_data is already void*.

Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Henrik Rydberg
f5274c972b hwmon: applesmc: add support for Macbook Air
This patch adds accelerometer, backlight and temperature sensor support
for the Macbook Air.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Henrik Rydberg
8bd1a12a51 hwmon: applesmc: allow for variable ALV0 and ALV1 package length
On some recent Macbooks, the package length for the light sensors ALV0 and
ALV1 has changed from 6 to 10.  This patch allows for a variable package
length encompassing both variants.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Henrik Rydberg
02fcbd144d hwmon: applesmc: prolong status wait
The time to wait for a status change while reading or writing to the SMC
ports is a balance between read reliability and system performance.  The
current setting yields rougly three errors in a thousand when
simultaneously reading three different temperature values on a Macbook
Air.  This patch increases the setting to a value yielding roughly one
error in ten thousand, with no noticable system performance degradation.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Henrik Rydberg
84d2d7f2ee hwmon: applesmc: fix the 'wait status failed: c != 8' problem
On many Macbooks since mid 2007, the Pro, C2D and Air models, applesmc
fails to read some or all SMC ports.  This problem has various effects,
such as flooded logfiles, malfunctioning temperature sensors,
accelerometers failing to initialize, and difficulties getting backlight
functionality to work properly.

The root of the problem seems to be the command protocol.  The current
code sends out a command byte, then repeatedly polls for an ack before
continuing to send or recieve data.  From experiments leading to this
patch, it seems the command protocol never quite worked or changed so that
one now sends a command byte, waits a little bit, polls for an ack, and if
it fails, repeats the whole thing by sending the command byte again.

This patch implements a send_command function according to the new
interpretation of the protocol, and should work also for earlier models.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Henrik Rydberg
05224091af hwmon: applesmc: specified number of bytes to read should match actual
At one single place in the code, the specified number of bytes to read and
the actual number of bytes read differ by one.  This one-liner patch fixes
that inconsistency.

Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Riki Oktarianto <rkoktarianto@gmail.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Jim Cromie
865c295360 hwmon/pc87360 separate alarm files: add therm-min/max/crit-alarms
Adds therm-min/max/crit-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the therm_group (of sysfs files)

The thermistors use voltage channels to measure; so they don't have a
fault-alarm, but unlike the other voltages, they do have an overtemp,
which we call crit (by convention).

[akpm@linux-foundation.org: cleanup]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Jim Cromie
8ca136741e hwmon/pc87360 separate alarm files: add dev_dbg help
temp and vin status register values may be set by chip specifications, set
again by bios, or by this previously loaded driver.  Debug output nicely
displays modprobe init=\d actions.

Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Jim Cromie
2a32ec2500 hwmon/pc87360 separate alarm files: define LDNI_MAX const
Driver handles 3 logical devices in fixed length array.  Give this a
define-d constant.

Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Jim Cromie
b267e8cdc6 hwmon/pc87360 separate alarm files: add temp-min/max/crit/fault-alarms
Adds temp-min/max/crit/fault-alarm callbacks, sensor-device-attribute
declarations, and refs to those new decls in the macro used to initialize
the temp_group (of sysfs files)

[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Jim Cromie
492e9657d1 hwmon/pc87360 separate alarm files: add in-min/max-alarms
Adds vin-min/max-alarm callbacks, sensor-device-attribute declarations,
and refs to those new decls in the macro used to initialize the vin_group
(of sysfs files)

[akpm@linux-foundation.org: cleanups]
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Jim Cromie
28f74e7177 hwmon/pc87360 separate alarm files: define some constants
Bring hwmon/pc87360 into agreement with
Documentation/hwmon/sysfs-interface.

Patchset adds separate limit alarms for voltages and temps, it also adds
temp[123]_fault files.  On my Soekris, temps 1,2 are unused/unconnected,
so temp[123]_fault = 1,1,0 respectively.  This agrees with
/usr/bin/sensors, which has always shown them as OPEN.  Temps 4,5,6 are
thermistor based, and dont have a fault bit in their status register.

This patch:

2 different kinds of constants added:
- CHAN_ALM_* constants for (later) vin, temp alarm callbacks.
- CHAN_* conversion constants, used in _init_device, partly for RW1C bits

Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-10-20 08:52:35 -07:00
Jean Delvare
a0cf354a71 hwmon: (adm1026) Prevent log spamming
When debugging is enabled, the adm1026 driver currently logs the
message "Setting VID from GPIO11-15" 108 times each time you run
"sensors". Once should be enough.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
2008-10-17 17:51:20 +02:00
Jean Delvare
885fe4b1f6 hwmon: (adm1026) Fix debug messages
* Add missing new-line to one debug message.
* Remove leading colon from 3 debug messages.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Philip Pokorny <ppokorny@penguincomputing.com>
2008-10-17 17:51:20 +02:00
Corentin Labbe
366716e6aa hwmon: (adm1029) Use mask for fan_div value
This is my patch for testing correct values of fan div in adm1029 and
prevent a division by 0 for some (unlikely) register values.

Signed-off-by: Corentin Labbe <corentin.labbe@geomatys.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:20 +02:00
Darrick J. Wong
21d93c14b3 hwmon: (ibmaem) Automatically load on IBM systems via DMI
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:19 +02:00
Darrick J. Wong
ff92136131 hwmon: (ibmpex) Automatically load on IBM systems via DMI
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:19 +02:00
Wolfgang Grandegger
0217eae3a8 hwmon: (w83781d) Use new style driver binding
This patch modifies the w83781d driver to use new style driver binding.
Substantial code modifications are required to deal with the new
interface, especially legacy device detection.

[JD: largely edited to make the patch smaller and to get the driver
to work again on ISA devices.]

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:19 +02:00
Jean Delvare
360782dde0 hwmon: (w83781d) Stop abusing struct i2c_client for ISA devices
Upcoming changes to the I2C part of the w83781d driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
2008-10-17 17:51:19 +02:00
Wolfgang Grandegger
443850ce58 hwmon: (w83781d) Make ISA interface depend on CONFIG_ISA
Probing the ISA bus on systems without ISA bus may hang the system.
This patch makes the ISA bus related code depend on the kernel
configuration parameter CONFIG_ISA. It moves ISA bus related code
into one #ifdef CONFIG_ISA ... #endif block and adds some helper
function.

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:18 +02:00
Jean Delvare
c6566206c6 hwmon: (w83781d) Detect alias chips
The W83781D and W83782D can be accessed either on the I2C bus or the
ISA bus. We must not access the same chip through both interfaces. So
far we were relying on the user passing the correct ignore parameter
to skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the w83781d
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.

So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
2008-10-17 17:51:18 +02:00
Jean Delvare
2fbbbf1488 hwmon: (w83781d) Refactor beep enable handling
We can handle the beep enable bit as any other beep mask bit for
slightly smaller code.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
2008-10-17 17:51:18 +02:00
Marc Hulsman
a5a4598cd2 hwmon: (w83791d) add support for thermal cruise mode
Add support to set target temperature and tolerance for thermal
cruise mode.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:17 +02:00
Marc Hulsman
b5938f8c4a hwmon: (w83791d) add pwm_enable support
Add support for pwm_enable.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:17 +02:00
Marc Hulsman
6495ce1840 hwmon: (w83791d) add manual PWM support
Add PWM manual control.

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:17 +02:00
Marc Hulsman
6e1ecd9b8f hwmon: (w83791d) fan 4/5 pins can also be used for gpio
Pins fan/pwm 4-5 can be in use as GPIO. If that is the case, do not
create their sysfs-interface. 

Signed-off-by: Marc Hulsman <m.hulsman@tudelft.nl>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:16 +02:00
Andrew Morton
a80e8ee667 hwmon: (max1619) Use inline functions instead of macros
Macros evaluating their arguments more than once are evil.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:16 +02:00
Jean Delvare
4ed1077953 hwmon: (it87) Fix thermal sensor type values
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.

Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
2008-10-17 17:51:16 +02:00
Jean Delvare
0c6e973171 hwmon: (lm78) Convert to a new-style i2c driver
The new-style lm78 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:16 +02:00
Jean Delvare
6e1b5029dc hwmon: (lm78) Stop abusing struct i2c_client for ISA devices
Upcoming changes to the I2C part of the lm78 driver will cause ISA
devices to no longer have a struct i2c_client at hand. So, we must
stop (ab)using it now.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:15 +02:00
Jean Delvare
ad3273be8e hwmon: (lm78) Prevent misdetection of Winbond chips
The LM78 detection is relatively weak, and sometimes recent Winbond
chips can be misdetected as an LM78. We have had repeated reports of
this happening. We have an explicit check against this for the ISA
access, do the same for I2C access now.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:15 +02:00
Jean Delvare
18c73f9042 hwmon: (lm78) Detect alias chips
The LM78 and LM79 can be accessed either on the I2C bus or the ISA
bus. We must not access the same chip through both interfaces. So far
we were relying on the user passing the correct ignore parameter to
skip the registration of the I2C interface as suggested by
sensors-detect, but this is fragile: the user may load the lm78
driver without running sensors-detect, and the i2c bus numbers are
not stable across reboots and hardware changes.

So, better detect alias chips in the driver directly, and skip any
I2C chip which is obviously an alias of the ISA chip. This is done
by comparing the value of 26 selected registers.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:15 +02:00
Jean Delvare
47c15532dd hwmon: (lm78) Fix I/O resource conflict with PNP
Only request I/O ports 0x295-0x296 instead of the full I/O address
range. This solves a conflict with PNP resources on a few motherboards.

Also request the I/O ports in two parts (4 low ports, 4 high ports)
during device detection, otherwise the PNP resource make the request
(and thus the detection) fail.

This is the exact same fix that was applied to driver w83781d in
March 2008 to address the same problem:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commit;h=2961cb22ef02850d90e7a12c28a14d74e327df8d

Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:15 +02:00
Jean Delvare
f908037a01 hwmon: (lm85) Better label names
Label names ERROR1 and ERROR3 aren't exactly explicit. Change them for
better names that indicate what we are up to.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17 17:51:14 +02:00
Jean Delvare
1b92adaddd hwmon: (lm85) Simplify RANGE_TO_REG
Function RANGE_TO_REG can easily be simplified. Credits go to Herbert
Poetzl for indirectly suggesting this to me. I tested that the new
implementation returns the same result as the original implementation
for all input values.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17 17:51:14 +02:00
Jean Delvare
67712d0192 hwmon: (lm85) Convert to a new-style i2c driver
The new-style lm85 driver implements the optional detect() callback
to cover the use cases of the legacy driver.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17 17:51:14 +02:00
Jean Delvare
8a0795d9b8 hwmon: (lm85) Support different PWM frequency tables
The Analog Devices and SMSC devices supported by the lm85 driver do
not have the same PWM frequency table as the National Semiconductor
devices. Add support for per-device frequency tables.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17 17:51:14 +02:00
Jean Delvare
86010c982d hwmon: (lm85) Select the closest PWM frequency
The LM85 and compatible chips only support 8 arbitrary PWM frequencies.
The algorithm to pick one of them based on the user input is not
optimum. Improve it to always pick the closest supported frequency.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17 17:51:13 +02:00
Jean Delvare
34e7dc6ca4 hwmon: (lm85) Implement the standard PWM frequency interface
Implement the standard PWM frequency interface: pwm[1-*]_freq in
units of 1 Hz, instead of the non-standard pwm[1-*]_auto_pwm_freq
in units of 0.1 Hz. The old naming was not only non-standard, it was
also confusing, because it suggested that the frequency value only
applied in automatic fan speed mode, which isn't true.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17 17:51:13 +02:00
Jean Delvare
69fc1feba2 hwmon: (lm85) Rework the device detection
Rework the device detection to make it clearer and faster in the
general case (when a known device is found.)

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Herbert Poetzl <herbert@13thfloor.at>
2008-10-17 17:51:13 +02:00
Dmitry Torokhov
dbee356262 hwmon: (ams) Simplify IRQ handling routine
Simplify the IRQ handling routine of ams driver.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:13 +02:00
Dmitry Torokhov
ee4cd32ee8 hwmon: (ams) Fix locking issues
Use a separate mutex to serialize input device creation/removal,
otheriwse we deadlock if we try to remove input device while it is
being polled. Also do not take ams_info.lock when it is not needed.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:12 +02:00
Dmitry Torokhov
0a02002268 hwmon: (ams) Fix permissions on 'joystick' module parameter
We should not allow writes to the 'joystick' module parameters since
writing there will not trigger creation of the input device. Disable
writes since we provide alternative way of enabling input device via
AMS device's sysfs attribute.

Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:12 +02:00
Jean Delvare
810ad7b62c hwmon: (ams) Convert to a new-style i2c driver
The legacy i2c binding model is phasing out, so the ams driver needs
to be converted to a new-style i2c driver. Here is a naive approach of
this conversion. Basically it is moving the i2c device creation from
the ams driver to the i2c-powermac driver. This should work, but I
suspect we could come up with something cleaner by declaring the i2c
device as part of the platform setup. This could be done later by
someone more familiar with openfirmware-based platforms than I am
myself.

One nice thing brought by this conversion is that the ams driver
should be loaded automatically on systems where is is needed (at
least when the I2C interface to the chip is used) providing
coldplug-aware user-space environment.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Stelian Pop <stelian@popies.net>
Cc: Michael Hanselmann <linux-kernel@hansmi.ch>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2008-10-17 17:51:12 +02:00
Ben Hutchings
47064d645b hwmon: (lm87) Add support for configuration through platform_data
The lm87 driver normally assumes that firmware configured the chip
correctly.  Since this is not always the case, alllow platform code to
set the channel register value via platform_data.  All other
configuration registers can be changed after driver initialisation.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:12 +02:00
Ben Hutchings
d2cac802fe hwmon: (lm87) Restore original configuration register on removal
This means that if we have to start the monitor when probed, we also
stop it on removal.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:11 +02:00
Ben Hutchings
49ae6cc800 hwmon: (lm87) Fix masking of config register in lm87_init_client()
lm87_init_client() conditionally sets the Start bit and clears the
INT#_Clear bit in the Config 1 register.  The condition should be that
either of these bits needs changing, but currently it checks the
(self-clearing) Initialization bit instead of INT#_Clear.

Fix the condition and also ensure we never set the Initialization bit.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
2008-10-17 17:51:11 +02:00