Commit graph

3663 commits

Author SHA1 Message Date
Vikram Pandita
e747951240 USB: musb: fix srp sysfs entry deletion
The SRP sysfs attribute is dependent on gadget mode; any
gadget may support SRP.  But "rmmod musb_hdrc" didn't
remove that attribute; fix.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Anand Gadiyar
5c23c9078f USB: musb: resume suspended root hub on disconnect
If this is not done, khubd will not be informed of the disconnect
and will assume the device is still there.

Easily seen when a hub is connected with no device attached to it;
it will autosuspend.  When the hub is disconnected, it still shows
up in /proc/bus/usb/devices

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
136733d612 USB: musb: use right poll limit for low speed devices
Remove wrongly applied upper limit on the interrupt transfer
interval for low speed devices (not much of an error per se,
according to USB specs).

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
3ecdb9acf3 USB: musb: be careful with 64K+ transfer lengths, host side
Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO
count in musb_host_tx() risks sending a short packet prematurely for
transfer sizes over 64 KB.

Similarly, although data transfer size shouldn't exceed 65535 bytes for
the control endpoint, making musb_h_ep0_continue() more robust WRT URBs
with possibly oversized buffer will not hurt either...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
51d9f3e100 USB: musb: fix data toggle saving with shared FIFO
For some strange reason the host side musb_giveback() decides
that it's always got an IN transfer when the hardware endpoint
is using a shared FIFO.  This causes musb_save_toggle() to read
the toggle state from the RXCSR register instead of TXCSR, and
may also cause unneeded reloading of RX endpoint registers.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
dc61d238b8 USB: musb: host endpoint_disable() oops fixes
The musb_h_disable() routine can oops in some cases:

 - It's not safe to read hep->hcpriv outside musb->lock,
   since it gets changed on completion IRQ paths.

 - The list iterators aren't safe to use in that way;
   just remove the first element while !list_empty(),
   so deletions on other code paths can't make trouble.

We need two "scrub the list" loops because only one branch
should touch hardware and advance the schedule.

[ dbrownell@users.sourceforge.net: massively simplify
  patch description; add key points as code comments ]

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
a2fd814e6a USB: musb: fix urb_dequeue() method
The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint.  That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.

Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback).  Since a QH with an empty URB
list is now supposed to be freed, do that.  And remove a now-useless
check from musb_advance_schedule().

[ dbrownell@users.sourceforge.net: update patch description,
  and fold in a dequeue() comment patch ]

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Dmitry Krivoschekov
b7bdcb79de USB: musb: fix musb_host_tx() for shared endpoint FIFO
The input queue should be used for TX on endpoints which
share FIFO hardware.  The host TX path wasn't doing that.

Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.

[ dbrownell@users.sourceforge.net: update patch description ]

Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Felipe Balbi
c2c963217b USB: musb: be careful with 64K+ transfer lengths (gadget side)
request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.

[ dbrownell@users.sourceforge.net: fix compiler warning ]

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
David Brownell
34f32c9701 usb: musb: make Davinci *work* in mainline
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:

 - Use clk_enable()/clk_disable() ... the "always enable USB clocks"
   code this originally relied on has since been removed.

 - Initialize the USB device only after the relevant I2C GPIOs are
   available, so the host side can properly enable VBUS.

 - Tweak init sequencing to cope with mainline's relatively late init
   of the I2C system bus for power switches, transceivers, and so on.

Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested.  Also
verified on OMAP3.

(Unrelated:  correct the MODULE_PARM_DESC spelling of musb_debug.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Alan Stern
67f5a4ba97 USB: usb_get_string should check the descriptor type
This patch (as1218) fixes a problem with a radio-control joystick used
in the "walkera 4#3" helicopter.  This device responds to the initial
Get-String-Descriptor request for string 0 (which is really the list
of supported languages) by sending its config descriptor!  The
usb_get_string() routine needs to check whether it got the right
type of descriptor.

Oddly enough, this sort of check is already present in
usb_get_descriptor().  The patch changes the error code from -EPROTO
to -ENODATA, because -EPROTO shows up in so many other contexts to
indicate a hardware failure rather than a firmware error.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Guillermo Jarabo <williamjap@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

===================================================================
2009-02-27 14:40:50 -08:00
David Brownell
54b9ed35ae USB: gadget: fix build error in omap_apollon_2420_defconfig
In apollon case, it only used udc, so udc configuration should select
USB_OTG_UTILS also.

Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Alan Stern
ce459ec1d2 USB: g_file_storage: automatically disable stalls under Atmel
This patch (as1220) automatically disables stalls when g_file_storage
finds itself running with an Atmel device controller, because the
Atmel hardware/driver isn't capable of halting bulk endpoints
correctly.

Reported-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Alan Stern
5126a2674d USB: usb-storage: add IGNORE_RESIDUE flag for Genesys Logic adapters
This patch (as1219) adds the IGNORE_RESIDUE flag to the unusual_devs
entries for Genesys Logic's USB-IDE adapter.  Although this device
usually gets the residue correct, there is one command crucial to the
operation of CD and DVD drives which it messes up.

Tested-by: Mike Lampard <mike@mtgambier.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Adam Richter
c332b4e1bf USB: Quirk for Hummingbird huc56s / Conexant ACM modem
Signed-off-by: Adam J. Richter <adam_richter2004@yahoo.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Patrik Kullman
5d7a4755d5 USB: serial: add support for second revision of Ericsson F3507G WWAN card
I noticed that my revision of the F3507G WWAN card isn't listed in
drivers/usb/serial/option.c

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Dmitriy Taychenachev
155df65ae1 USB: cdc-acm: add usb id for motomagx phones
The Motorola MOTOMAGX phones (Z6, E8, Zn5 so far) are providing
combined ACM/BLAN USB configuration. Since it has Vendor Specific
class, the corresponding drivers (cdc-acm, zaurus) can't find it just
by interface info. This patch adds usb id so the cdc-acm driver can
properly handle this combined device.

Signed-off-by: Dmitriy Taychenachev <dimichxp@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Jesse Sung
28fb66821f USB: option: add BenQ 3g modem information
This patch addes the BenQ 3g modem support to the option driver.


From: Jesse Sung <jsung@novell.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Felipe Balbi
29a46bf6f4 usb: gadget: obex: select correct ep descriptors
We where selecting wrong ep descriptors causing
some troubles while sending files over obex interface.

The problem was a typo while usb_find_endpoint() was being
called for HS endpoints.

Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Karsten Wiese
9aa09d2f8f USB: EHCI: slow down ITD reuse
Currently ITDs are immediately recycled whenever their URB completes.
However, EHCI hardware can sometimes remember some ITD state.  This
means that when the ITD is reused before end-of-frame it may sometimes
cause the hardware to reference bogus state.

This patch defers reusing such ITDs by moving them into a new ehci member
cached_itd_list. ITDs resting in cached_itd_list are moved back into their
stream's free_list once scan_periodic() detects that the active frame has
elapsed.

This makes the snd_usb_us122l driver (in kernel since .28) work right
when it's hooked up through EHCI.

[ dbrownell@users.sourceforge.net: comment fixups ]

Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Tested-by: Philippe Carriere <philippe-f.carriere@wanadoo.fr>
Tested-by: Federico Briata <federicobriata@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Li Yang
9a6e184c80 USB: fsl_usb2_udc: fix potential queue head corruption
Clear next TD field and status field in queue head initialization code
to prevent unpredictable result caused by residue of usb reset.

Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:50 -08:00
Linus Torvalds
402a917aca Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] 5405/1: ep93xx: remove unused gesbc9312.h header
  [ARM] 5404/1: Fix condition in arm_elf_read_implies_exec() to set READ_IMPLIES_EXEC
  [ARM] omap: fix clock reparenting in omap2_clk_set_parent()
  [ARM] 5403/1: pxa25x_ep_fifo_flush() *ep->reg_udccs always set to 0
  [ARM] 5402/1: fix a case of wrap-around in sanity_check_meminfo()
  [ARM] 5401/1: Orion: fix edge triggered GPIO interrupt support
  [ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device controller
  [ARM] 5391/1: AT91: Enable GPIO clocks earlier
  [ARM] 5390/1: AT91: Watchdog fixes
  [ARM] 5398/1: Add Wan ZongShun to MAINTAINERS for W90P910
  [ARM] omap: fix _omap2_clksel_get_src_field()
  [ARM] omap: fix omap2_divisor_to_clksel() error return value
2009-02-19 09:52:12 -08:00
Roel Kluin
22eb36f49e [ARM] 5403/1: pxa25x_ep_fifo_flush() *ep->reg_udccs always set to 0
*ep->reg_udccs is always set to 0.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-19 11:04:46 +00:00
Rafael J. Wysocki
3494252d56 USB/PCI: Fix resume breakage of controllers behind cardbus bridges
If a USB PCI controller is behind a cardbus bridge, we are trying to
restore its configuration registers too early, before the cardbus
bridge is operational.  To fix this, call pci_restore_state() from
usb_hcd_pci_resume() and remove usb_hcd_pci_resume_early() which is
no longer necessary (the configuration spaces of USB controllers that
are not behind cardbus bridges will be restored by the PCI PM core
with interrupts disabled anyway).

This patch fixes the regression from 2.6.28 tracked as
http://bugzilla.kernel.org/show_bug.cgi?id=12659

[ Side note: the proper long-term fix is probably to just force the
  unplug event at suspend time instead of doing a plug/unplug at resume
  time, but this patch is fine regardless  - Linus ]

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-17 16:56:31 -08:00
David Vrabel
a3c1239eb5 wusb: whci-hcd: always lock whc->lock with interrupts disabled
Always lock whc->lock with spin_lock_irq() or spin_lock_irqsave().

Signed-off-by: David Vrabel <david.vrabel@csr.com>
2009-02-16 14:37:12 +00:00
Nick Holloway
049a6acb50 USB: Storage: Update unusual_devs entry for Datafab KECF-USB
This device suffers from the off-by-one error when reporting the capacity,
so add US_FL_FIX_CAPACITY to the existing entry.

Signed-off-by: Nick Holloway <Nick.Holloway@pyrites.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:49 -08:00
Ivan Kuten
26e1287594 USB: Correct Makefile to make isp1760 buildable
Signed-off-by: Ivan Kuten <ivan.kuten@promwad.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:49 -08:00
Dirk De Schepper
c200b9c9e8 USB: option: New mobile broadband modems to be supported
- New Novatel and Dell mobile broadband modem products added
 - Dell pid variables used in stead of numerical PIDs for known
   products

Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:48 -08:00
Oliver Neukum
97dcf0416e USB: two more usb ids for ti_usb_3410_5052
This patch adds device IDs and balances the counts to make the
hot ID additioning mechanism work.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@kernel.org>
Cc: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:48 -08:00
Dan Carpenter
64905b4809 USB: ftdi_sio: unlock_kernel() on error in set_serial_info()
There was one error path where unlock_kernel() wasn't called.

This was found with a code checker (http://repo.or.cz/w/smatch.git/)
Compile tested only, sorry.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:48 -08:00
Alan Stern
506e946983 USB: usb-storage: add Pentax to the bad-vendor list
This patch (as1202) adds Pentax to usb-storage's list of bad vendors
whose devices always need the CAPACITY_HEURISTICS flag.  This is in
addition to the existing entries: Nokia, Nikon, and Motorola.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Virgo Pärna <virgo.parna@mail.ee>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:48 -08:00
Stephane Clerambault
e38c287447 USB: ftdi_sio: add support for the NDI Polaris system
Add support for the NDI Polaris system *http://www.ndigital.com/).

Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:48 -08:00
Dave Young
78c8fb3717 USB: usb-serial: fix the aircable_init failure path
The failure path of aircable_init is wrong, fix the order of (goto) labels.

Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Naranjo Manuel Francisco <naranjo.manuel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:48 -08:00
Alan Stern
0d020aae0a USB: usb-storage: remove WARN from last-sector hacks
This patch (as1201) removes the WARN() from the last-sector hacks in
usb-storage, thereby making the code match the version now in
.27-stable and .28-stable.  The WARN() isn't needed, since there is no
longer any intention of assuming that all storage devices have an even
number of sectors, and it annoys users for no good reason.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:47 -08:00
Greg Kroah-Hartman
6b40c0057a Revert USB: option: add Pantech cards
Revert 8b6346ec89 as these devices really
work just fine with the cdc-acm driver, as they follow the spec
properly.

Thanks to Chuck Ebbert for pointing out the problem here.

Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:47 -08:00
James Treacy
2057ac86da USB: cdc-acm.c: remove duplicate lines for MTK gps support
The same patch to add support for MTK gps loggers was submitted by two
different people and applied twice. Remove the redundant lines.

Signed-off-by: James Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:47 -08:00
Anton Vorontsov
af3ddbd763 USB: fsl_qe_udc: Fix stalled TX requests bug
While disabling an endpoint the driver nuking any pending requests,
thus completing them with -ESHUTDOWN status. But the driver doesn't
clear the tx_req, which means that a next TX request (after
ep_enable), might get stalled, since the driver won't queue the new
reqests.

This patch fixes a bug I'm observing with ethernet gadget while
playing with ifconfig usb0 up/down (the up/down sequence disables
and enables `in' and `out' endpoints).

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:47 -08:00
Anton Vorontsov
82341b3690 USB: fsl_qe_udc: Fix muram corruption by disabled endpoints
Before freeing an endpoint's muram memory, we should stop all activity
of the endpoint, otherwise the QE UDC controller might do nasty things
with the muram memory that isn't belong to that endpoint anymore.

The qe_ep_reset() effectively flushes the hardware fifos, finishes all
late transaction and thus prevents the corruption.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:47 -08:00
Anton Vorontsov
ef84e4055f USB: fsl_qe_udc: Fix disconnects reporting during bus reset
Freescale QE UDC controllers can't report the "port change" states,
so the only way to handle disconnects is to process bus reset
interrupts. The bus reset can take some time, that is, few irqs.
Gadgets may print the disconnection events, and this causes few
repetitive messages in the kernel log.

This patch fixes the issue by using the usb_state machine, if the
usb controller has been already reset, just quit the reset irq
early.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:47 -08:00
Anton Vorontsov
2247818a32 USB: fsl_qe_udc: Fix QE USB controller initialization
qe_udc_reg_init() leaves the USB controller enabled before muram memory
initialized. Sometimes the uninitialized muram memory confuses the
controller, and it start sending the busy interrupts.

Fix this by disabling the controller, it will be enabled later by
the gadget driver, at bind time.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:47 -08:00
Anton Vorontsov
a30551db66 USB: fsl_qe_udc: Fix recursive locking bug in ch9getstatus()
The call chain is this:

qe_udc_irq() <- grabs the udc->lock spinlock
rx_irq()
qe_ep0_rx()
ep0_setup_handle()
setup_received_handle()
ch9getstatus()
qe_ep_queue() <- tries to grab the udc->lock again

It seems unsafe to temporarily drop the lock in the ch9getstatus(),
so to fix that bug the lock-less __qe_ep_queue() function
implemented and used by the ch9getstatus().

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:46 -08:00
Anton Vorontsov
94f341db3d USB: fsl_qe_udc: Fix oops on QE UDC probe failure
In case of probing errors the driver kfrees the udc_controller, but it
doesn't set the pointer to NULL.

When usb_gadget_register_driver is called, it checks for udc_controller
!= NULL, the check passes and the driver accesses nonexistent memory.
Fix this by setting udc_controller to NULL in case of errors.

While at it, also implement irq_of_parse_and_map()'s failure and cleanup
cases.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-09 11:19:46 -08:00
David Vrabel
8f04915532 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 into for-upstream 2009-02-02 17:52:39 +00:00
Anton Vorontsov
236dd4d18f USB: Driver for Freescale QUICC Engine USB Host Controller
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.

Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.

This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:38 -08:00
Alex.Cheng@quantatw.com
fc91be2ad0 USB: option: add QUANTA HSDPA Data Card device ids
This patch adds the support  for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.

Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:37 -08:00
Phil Dibowitz
aa23c8d616 USB: storage: Add another unusual_dev for off-by-one bug
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.

Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>

Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:37 -08:00
Phil Dibowitz
a83775b146 USB: unusual_dev: usb-storage needs to ignore a device
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.


At this time usb_modeswitch does not work with this device.


Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:37 -08:00
Roel Kluin
0df2479232 USB: GADGET: fix !x & y
! has a higher precedence than &

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:37 -08:00
Oliver Neukum
1a1fab5137 USB: new id for ti_usb_3410_5052 driver
This adds a new device id

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:37 -08:00
Alan Cox
c89c60e9d6 USB: cdc-acm: Add another conexant modem to the quirks
Another Conexant, another device with the same quirk

Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:37 -08:00