In function fops_open variable type was set but not used. Tested by compilation only.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Michael Hunold <michael@mihu.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes compared to version 0.1 of driver (sent 6 May):
- Initial implementation of get_rf_strength function.
- Introduction of a warning message
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Common defines for the FC0012 (v0.5) and FC0013 tuner drivers
Signed-off-by: Hans-Frieder Vogt <hfvogt@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Besides the usual inconsistencies in input enumeration there was also a
kernel crash if you tried to poll on a vbi node. The checks for sliced
vbi output vs vbi capture were not complete enough.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The querycap ioctl returned an incorrect version number and incorrect
capabilities (mixing up vbi and video caps).
The reason for that was that video nodes could do vbi activities: that
should be separated between the vbi and video nodes.
There were also a few minor problems with dbg_g/s_register that have
been resolved. The mxb/saa7146 driver now passes the v4l2_compliance tests.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use v4l2_fh which gives you control events and priority handling for free.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There was also a vbi_q and video_q in saa7146_fh, so that was confusing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This information can also be retrieved from struct video_device.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fields are global and don't belong in a fh struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a global structure and does not belong to saa7146_fh.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is global information, not per-filehandle information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert to the control framework, fix the easy v4l2-compliance failures.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This used to be the default if the lock pointer was set, but now that lock is by
default only used for ioctl serialization. Those drivers that already used
core locking have this flag set explicitly, except for some drivers where
it was obvious that there was no need to serialize any file operations other
than ioctl.
The drivers that didn't need this flag were:
drivers/media/radio/dsbr100.c
drivers/media/radio/radio-isa.c
drivers/media/radio/radio-keene.c
drivers/media/radio/radio-miropcm20.c
drivers/media/radio/radio-mr800.c
drivers/media/radio/radio-tea5764.c
drivers/media/radio/radio-timb.c
drivers/media/video/vivi.c
sound/i2c/other/tea575x-tuner.c
The other drivers that use core locking and where it was not immediately
obvious that this flag wasn't needed were changed so that the flag is set
together with a comment that that driver needs work to avoid having to
set that flag. This will often involve taking the core lock in the fops
themselves.
Eventually this flag should go and it should not be used in new drivers.
There are a few reasons why we want to avoid core locking of non-ioctl
fops: in the case of mmap this can lead to a deadlock in rare situations
since when mmap is called the mmap_sem is held and it is possible for
other parts of the code to take that lock as well (copy_from_user()/copy_to_user()
perform a down_read(&mm->mmap_sem) when a page fault occurs).
It is very unlikely that that happens since the core lock serializes all
fops, but the kernel warns about it if lock validation is turned on.
For poll it is also undesirable to take the core lock as that can introduce
increased latency. The same is true for read/write.
While it was possible to make flags or something to turn on/off taking the
core lock for each file operation, in practice it is much simpler to just
not take it at all except for ioctl and leave it to the driver to take the
lock. There are only a handful fops compared to the zillion ioctls we have.
I also wanted to make it obvious which drivers still take the lock for all
fops, so that's why I chose to have drivers set it explicitly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than loading firmware specific for the xtal frequency, just use
the standard firmware and set the xtal frequency after firmware upload.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that i2c transfers are fixed, 3 retries are enough.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use usleep_range() instead of msleep() to improve power saving opportunities.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds support for the Fitipower fc0011 DVB-t tuner.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Without this we have got the warnings like following if build with "make W=1
O=/var/tmp":
cc1: warning: drivers/media/dvb/dvb-core: No such file or directory [enabled by default]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 99ac541254 removed
the function mt2063_setTune() from mt2063.c. Remove it
also from the header file.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Specify chip revision at attach time rather than a firmware image.
This is a better way to ensure that the correct firmware is loaded
for the correct revision of the chip.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
convert the firmware configuration attach-time parameter from
a pointer to an integer so as to remove the static dependency
created by the previous changesets.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
newer versions of the xc5000 silicon require newer firmware
while remaining 100% driver compatible. original versions
of the xc5000a continue to use the same firmware.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix for some -Wuninitialized compiler warnings.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase mt2063 frequency_max to tune to channel 69(858Mhz).
Jose Alberto
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some changes are needed, in order to make az6007 compile with the
upstream tree. Most of the changes are due to the upstream drxk
module.
Even allowing its compilation, the driver is not working yet.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In xc4000 chipsets real signal and noise level is stored in register
0x0A and 0x0B,so we can use those registers to monitor signal strength.
I tested this patch on 2 different cards Leadtek DVR3200 and DTV2000H
Plus, both with same results, I used special antenna hubs (toner 4x, 6x,
8x and 12x) with mesured signal lost, both registers are in dB value,
first represent signal with limit value -113.5dB (should be -114dB) and
exactly match with test results. Second represents noise level also in
dB and there is no maximum value, but from tests we can drop everything
above 32dB which tuner realy can't use, signal was usable till 20dB
noise level.
In digital mode we can take signal strength but sadly noise level is not
relevant and real value is stored in demodulator for now just zl10353,
also digital mode is just for testing, because it needs changing other
parts of code which reads data only from demodulator.
In analog mode I was able to test only FM radio, signal level is not
important, it says something about cable and hub losts, but nothing
about real quality of reception, so even if we have signal level at
minimum 113dB we can still here radio, because of that it is displaied
only in debug mode, but for real signal level is used noise register
which is again very accurate, radio noise level was betwen 6-20dB for
good signal, 20-25dB for medium signal, and above 25dB signal is
unusable.
For now real benefit of this patch is only for FM radio mode.
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DVB-T did not work at all - only 6 MHz was working but it is not
commonly used.
Fix it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch replaces the previous one proposed in the thread "xc3028:
force reload of DTV7 firmware in VHF band with Zarlink demodulator",
at the linux-media@vger.kernel.org ML.
The problem is that the firmware DTV78 works fine in UHF band (8 MHz
bandwidth) but is not working at all in VHF band (7 MHz bandwidth).
Reading the comments inside the code, I figured out that the real
problem could be connected to the formula used to calculate the center
frequency offset in VHF band.
In fact, removing this adjustment fixes the problem:
if ((priv->cur_fw.type & DTV78) && freq < 470000000)
offset -= 500000;
This is coherent to what was implemented for the DTV7 firmware by an
Australian user:
if (priv->cur_fw.type & DTV7)
offset += 500000;
In the end, now the center frequency is the same for all firmwares
(DTV7, DTV8, DTV78) and doesn't depend on channel bandwidth.
The final code looks clean and simple, and there is no need for any
"magic" adjustment:
if (priv->cur_fw.type & DTV6)
offset = 1750000;
else /* DTV7 or DTV8 or DTV78 */
offset = 2750000;
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, ops->info.type is handled inside the dvb_frontend
core, only for DVBv3 calls, and according with the
delivery system. So, drivers should not care or use it,
otherwise, it may have issues with DVBv5 calls.
The drivers that were still using it were detected via
this small temporary hack:
--- a/include/linux/dvb/frontend.h
+++ b/include/linux/dvb/frontend.h
@@ -29,13 +29,16 @@
#include <linux/types.h>
typedef enum fe_type {
+#if defined(__DVB_CORE__) || !defined (__KERNEL__)
FE_QPSK,
FE_QAM,
FE_OFDM,
FE_ATSC
+#else
+FE_FOOO
+#endif
} fe_type_t;
-
typedef enum fe_caps {
FE_IS_STUPID = 0,
FE_CAN_INVERSION_AUTO = 0x1,
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The per-delivery system tables are confusing.
Add an extra table that explains them, and some
dprintk calls, that allows to check if mt2063 driver
is working as expected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of printing it just for debug purposes, outputs the detected
version at the logs. This may be useful if someone wants to report
a problem.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While here, improve a few debug messages that helped to track the
issue and may be useful in the future.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This also helps to identify when a device is not initialized,
if the bridge doesn't return an error for a I2C failed transfer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of crash, return -ENODEV, if the device is not poperly
initialized.
Also, give a second chance for it to initialize, at set_params
calls.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mt2063.c:1531:12: warning: variable 'ofout' set but not used [-Wunused-but-set-variable]
mt2063.c:1531:6: warning: variable 'ofin' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several vars at set_parms functions were set, but unused.
Remove them and change the logic to return -EINVAL if the
analog set_param is used for digital mode.
At the analog side, cleans the logic that sets the several
analog standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
No functional changes on this patch. Better organize the delivery
system information and data types, putting everything together,
to improve readability.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver were using a hacky way of setting analog and digital
frequencies. Remove the hack and properly add the tuner logic for
each supported type of standard.
I was tempted to add more standards there, like SECAM and to fix
radio (as stepping seems broken), but I opted to keep it as-is,
as tests would be needed to add additional standards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Such code is disabled via ifdef's. Also, they're ugly and rely
on some static structures. Just remove. If ever needed, the git
log can be used to recover it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a big patch, yet trivial: now that all tuners use the DVBv5
way to pass parameters (e. g. via fe->dtv_property_cache), the
extra parameter can be removed from set_params() call.
After this change, very few DVBv3 specific stuff are left at the
tuners.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The calc_regs() callback is used by a few frontends (mt352, nxt200x,
digitv and zl10353). On all places it is called, the parameters are
set by DVBv5 way. So, just use the DVBv5 struct and remove the
extra parameter.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Despite its name, tuner-simple has a complex logic to set freqs ;)
Basically, it can be called by two different ways: via set_params()
or via calc_regs() callbacks. Both are bound to the DVBv3 API.
Also, set_params internally calls calc_regs().
In order to get rid of DVBv3 params at set_params(), it shouldn't
call calc_regs() anymore. The code duplication is very small,
as most of the code there is just to check for invalid parameters.
With regards to calc_regs(), it should still trust on bandwidth and
frequency parameters passed via DVBv3, until a later patch fixes
it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This standard is not properly documented, but its settings are at
the tda18271dd driver, and are somewhat obvious, as they follow
the same logic as DVB-T 7MHz.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is a bug on mxl5005s logic: when the bandwidth changes, but using
the same delivery system, the code discard the set_params()
reconfiguration request.
This was happening because, in the previous coding, the bandwidth
calculus were after the check for delivery system changes.
The previous patch changed the logic to estimate the bandwidth to
happend together with the changes at the delivery system.
So, with a one-statement change, it is possible to make the tuner to
reconfigure, in order to adjust to bandwidth changes. this will
likely fix issues on countries that use 7MHz/8MHz DVB-T channels.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
