In the case where a gadget driver is removed while no
transceiver was found at probe time, a bug in
otg_put_transceiver() will trigger.
Provide symetric calls for otg_get_transceiver() and
otg_put_transceiver(), wherever a transceiver was found or
not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch to cdc-wdm
- checks for partial extra descriptors
- fixes a leak in the error case of probe
- checks for an exact number of endpoints
- adds a clarifying comment
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes tty->low_latency from all USB serial drivers that push
data into the tty layer at hard interrupt context. It's no longer needed
and actually harmful.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a problem in sierra_send_setup() function when
composite devices are used. One should not be sending ACM commands to
interfaces that are OBEX. Doing this causes an apparent failure as the
ACM command has to time out before the interface can start being used.
Signed-off-by: Elina Pasheva <epasheva@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We now have a more correct solution for shrinking runtime driver
footprints than just marking probe() as __init ... use it.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build error in the MIPS USB IP core family device controller driver.
The driver calls udelay() without including linux/delay.h
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When I want to use my webcam, I get:
vvvvvvv
cheese: page allocation failure. order:5, mode:0x8004
Pid: 8100, comm: cheese Not tainted 2.6.30-rc2-wl-dirty #102
Call Trace:
[<ffffffff802c5d8e>] __alloc_pages_internal+0x3fe/0x520
[<ffffffff80210a20>] dma_generic_alloc_coherent+0x90/0x120
[<ffffffffa001c91e>] hcd_buffer_alloc+0xee/0x130 [usbcore]
[<ffffffffa000d52d>] usb_buffer_alloc+0x2d/0x40 [usbcore]
[<ffffffffa0160e14>] uvc_alloc_urb_buffers+0x84/0x140 [uvcvideo]
[<ffffffffa0160ff6>] uvc_init_video+0x126/0x400 [uvcvideo]
[...]
Oddly, I remembered fixing this and putting in __GFP_NOWARN
because uvcvideo retries a smaller allocation. However, the
allocation function doesn't pass the gfp flags through to
dma_alloc_coherent so we still get the warning!
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1231) fixes a use-after-free bug in g_file_storage. A
device's name may not be available after the device is unregistered,
even if the device structure itself is still allocated. Since
close_backing_file() prints a LUN's name for debugging, it shouldn't
be called after the LUN has been unregistered.
That whole area needed to be cleaned up; the backing files were
getting closed in a couple of different places. The patch fixes
things so that they get closed in just one place, as part of the
unbind procedure, immediately before the LUN is unregistered.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without this patch, the driver won't check that the last fully-occupied
uframe for a new split transaction was vacant beforehand. This can
lead to a situation in which the first 188 bytes of a 192-byte
isochronous transfer are scheduled in the same uframe as an existing
interrupt transfer. The resulting schedule looks like this:
uframe 0: 188-byte isoc-OUT SSPLIT, 8-byte int-IN SSPLIT
uframe 1: 4-byte isoc-OUT SSPLIT
The SSPLITs are intermingled, causing an error in the downstream hub's
TT.
If you are having problems with devices or hub ports resetting, or failed
interrupt transfers, when you start using a USB audio or video (Isochronous)
device, this patch may help.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Reported-by: Kung James <kong1191@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
This patch fixes a problem with any mos7840 device where the use of the field "minor" before it is
initialised results in all the devices being overlaid in memory (minor = 0 for all instances)
Contributed by: Phillip Branch
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add USB ids for the mos7840 based ATEN International serial devices.
Contributed by: Phillip Branch
Signed-off-by: Tony Cook <tony-cook@bigpond.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix this build error when CONFIG_PM is not set:
drivers/usb/musb/musb_core.c:2232: error: 'musb_resume_early' undeclared here
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This email address is going to expire soon and my contribution to musb
is next to zero so remove it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bug Fix: high speed detection in LPM mode
Bug Fix: max packet size configuration when switching between HS and FS
Signed-off-by: David Lopo <dlopo@chipidea.mips.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported by Alessio Treglia on
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/125250
User was getting the following errors in dmesg:
[ 2158.139386] sd 5:0:0:1: ioctl_internal_command return code = 8000002
[ 2158.139390] : Current: sense key: No Sense
[ 2158.139393] Additional sense: No additional sense information
Adds unusual device support.
modified: drivers/usb/storage/unusual_devs.h
Signed-off-by: Chuck Short <zulcss@ubuntu.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1229) fixes a few lifetime and locking problems in the
usb-serial driver. The main symptom is that an invalid kevent is
created when the serial device is unplugged while a connection is
active.
Ports should be unregistered when device is disconnected,
not when the parent usb_serial structure is deallocated.
Each open file should hold a reference to the corresponding
port structure, and the reference should be released when
the file is closed.
serial->disc_mutex should be acquired in serial_open(), to
resolve the classic race between open and disconnect.
serial_close() doesn't need to hold both serial->disc_mutex
and port->mutex at the same time.
Release the subdriver's module reference only after releasing
all the other references, in case one of the release routines
needs to invoke some code in the subdriver module.
Replace a call to flush_scheduled_work() (which is prone to
deadlocks) with cancel_work_sync(). Also, add a call to
cancel_work_sync() in the disconnect routine.
Reduce the scope of serial->disc_mutex in serial_disconnect().
The only place it really needs to protect is where the
"disconnected" flag is set.
This fixes the bug reported in
http://bugs.freedesktop.org/show_bug.cgi?id=20703
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dan Williams <dcbw@redhat.com>
Tested-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bugfixes noted by checking the code against the controller
documentation (TI document number SPRUE21):
- Remove declarations for eight non-existent registers (!);
and remove accesses to two of them.
- Remove access to various non-existent bitfields in some of
the registers which *do* exist (those fields must-be-zero).
- Provide comment to replace bogus reset logic (removed above,
it relied on non-existent bitfields). Resets require GPIO
help; this driver doesn't currently know about that.
With some minor cleanup: relocate a comment, avoid an extra
lookup of the PIO timings.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
tape_3590_offline and tape_34xx_offline are removed and tape_generic_offline
is called directly instead.
Signed-off-by: Frank Munzert <munzert@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Linux-2.6.29 deleted the legacy ACPI idle handler, leaving
the CPU_IDLE handler, which does not track bus master activity.
So delete the unused bm_activity field -- it is confusing to
print an always zero value.
This patch could break programs that parse
/proc/acpi/processor/*/power, since it deletes this
line from that file:
bus master activity: 00000000
http://bugzilla.kernel.org/show_bug.cgi?id=13145
is not fixed by this patch, but provoked this patch.
Signed-off-by: Len Brown <len.brown@intel.com>
The c2 and c3 idle handlers check tsc_halts_in_c()
after every time they return from idle. Um, when?:-)
Move this check to init-time to remove the unnecessary
run-time overhead, and also to have the check complete before
the first entry into the idle handler.
ff69f2bba6
(acpi: fix of pmtimer overflow that make Cx states time incorrect)
replaced the hard-coded use of the PM-timer inside idle,
with ktime_get_readl(), which possibly uses the TSC --
so it is now especially prudent to detect a broken TSC
before entering idle.
http://bugzilla.kernel.org/show_bug.cgi?id=13087
Signed-off-by: Len Brown <len.brown@intel.com>
commit 7a192ec334 ("platform driver: fix
incorrect use of 'platform_bus_type' with 'struct device_driver') turned a
driver_UNregister into platform_driver_REGISTER. Correct this to
platform_driver_UNregister.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
On Tuesday 14 April 2009 20:31:21 Subrata Modak wrote:
> Observed the following build error:
> ---
> CC drivers/macintosh/mediabay.o
> In file included from drivers/macintosh/mediabay.c:21:
> include/linux/ide.h:605: error: field ‘request_sense_rq’ has incomplete
> type
> make[2]: *** [drivers/macintosh/mediabay.o] Error 1
> make[1]: *** [drivers/macintosh] Error 2
> make: *** [drivers] Error 2
> ---
mediabay shouldn't include <linux/ide.h> unconditionally so
remove the superfluous include from mediabay.c (<asm/mediabay.h>
will pull <linux/ide.h> in for CONFIG_BLK_DEV_IDE_PMAC=y).
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
With 2.6.30-rc2 I face a kernel crash on the 32bit hppa architecture
due to ide-cd when udev creates the device nodes at startup:
Kernel Fault: Code=26 regs=8ed34c40 (Addr=00000024)
IASQ: 00000000 00000000 IAOQ: 1034b5ac 1034b5b0
IIR: 4ab30048 ISR: 00000000 IOR: 00000024
CPU: 0 CR30: 8ed34000 CR31: ffff55ff
ORIG_R28: 00000000
IAOQ[0]: ide_complete_rq+0x2c/0x70
IAOQ[1]: ide_complete_rq+0x30/0x70
RP(r2): cdrom_newpc_intr+0x178/0x46c
Backtrace:
[<1035c608>] cdrom_newpc_intr+0x178/0x46c
[<1034c494>] ide_intr+0x1b0/0x214
[<1016d284>] handle_IRQ_event+0x70/0x150
[<1016d4b0>] __do_IRQ+0x14c/0x1cc
[<102f7864>] superio_interrupt+0x88/0xbc
[<1016d284>] handle_IRQ_event+0x70/0x150
[<1016d4b0>] __do_IRQ+0x14c/0x1cc
[<10112efc>] do_cpu_irq_mask+0x9c/0xd0
[<10116068>] intr_return+0x0/0x4
This crash seems to happen due to an uninitialized variable "rc".
The compiler even warns about that:
CC drivers/ide/ide-cd.o
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c: In function `cdrom_newpc_intr':
/mnt/sda4/home/cvs/parisc/git-kernel/linus-linux-2.6/drivers/ide/ide-cd.c:612: warning: `rc' might be used uninitialized in this function
After applying the trivial patch below, which just initializes
the variable to zero, the kernel doesn't crash any longer:
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...
hda: command error: status=0x51 { DriveReady SeekComplete Error }
hda: command error: error=0x54 <3>{ AbortedCommand LastFailedSense=0x05 }
ide: failed opcode was: unknown
done.
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Borislav Petkov <petkovbb@gmail.com>
Cc: Linus <torvalds@linux-foundation.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix UDMA throughput bug: tCYC averages t2CYCTYP/2, but the code
previously assumed it was the same as t2CYCTYP. (That is, it was
using just one clock edge, not both.) Move the table's type
declaration so it's adjacent to the table, making it more clear
what those numbers mean.
On one system this change increased throughput by almost 4x: UDMA/66
sometimes topped 23 MB/sec (on a drive known to do much better). On
another system it was around a 10% win (UDMA/66 up to 7+ MB/sec).
The difference might be caused by the ratio between memory and IDE
clocks. In the system with large speedup, this was exactly 2 (as a
workaround for a rev 1.1 silicon bug). The other system used a more
standard ratio of 1.63 (and rev 2.1 silicon) ... clock domain synch
might have some issues, they're not unheard-of.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
If using the UCC on a MPC8360 in RMII mode, don;t set
UCC_GETH_UPSMR_RPM bit in the upsmr register.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While ifconfig eth0 up kernel calls open() of 8139 driver(8139too.c).
In rtl8139_hw_start() of rtl8139_open(), 8139 driver enable RX before
setting up the DMA buffer address. In this interval where RX was
enabled and DMA buffer address is not yet set up, any incoming
broadcast packet would be send to a strange physical address:
0x003e8800 which is the default value of DMA buffer address.
Unfortunately, this address is used by Linux kernel. So kernel panics.
This patch fix it by setting up DMA buffer address before RX enabled
and everything is fine even under broadcast packets attack.
Signed-off-by: Jonathan Lin <jon.lin@vatics.com>
Signed-off-by: Amos Kong <jianjun@zeuux.org>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the powermac IDE host driver can be modular, we need to
export check_media_bay_by_base() and media_bay_set_ide_infos()
from drivers/macintosh/mediabay.c for it.
This fixes the following build error:
> CC [M] drivers/ide/pmac.o
> drivers/ide/pmac.c: In function ‘pmac_ide_init_dev’:
> drivers/ide/pmac.c:955: error: implicit declaration of function
> ‘check_media_bay_by_base’
> drivers/ide/pmac.c: In function ‘pmac_ide_setup_device’:
> drivers/ide/pmac.c:1090: error: implicit declaration of function
> ‘media_bay_set_ide_infos’
> make[2]: *** [drivers/ide/pmac.o] Error 1
> make[1]: *** [drivers/ide] Error 2
> make: *** [drivers] Error 2
Reported-by: Subrata Modak <subrata@linux.vnet.ibm.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixes this build error:
In file included from drivers/macintosh/mediabay.c:21:
include/linux/ide.h:605: error: field 'request_sense_rq' has incomplete type
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is currently only one way for userspace to say "wait for my storage
device to get ready for the modules I just loaded": to load the
scsi_wait_scan module. Expectations of userspace are that once this
module is loaded, all the (storage) devices for which the drivers
were loaded before the module load are present.
Now, there are some issues with the implementation, and the async
stuff got caught in the middle of this: The existing code only
waits for the scsy async probing to finish, but it did not take
into account at all that probing might not have begun yet.
(Russell ran into this problem on his computer and the fix works for him)
This patch fixes this more thoroughly than the previous "fix", which
had some bad side effects (namely, for kernel code that wanted to wait for
the scsi scan it would also do an async sync, which would deadlock if you did
it from async context already.. there's a report about that on lkml):
The patch makes the module first wait for all device driver probes, and then it
will wait for the scsi parallel scan to finish.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A few issues wrt DMA were uncovered when using the driver with swiotlb.
- driver should not use memory after it has been mapped
- iwl3945's RX queue management cannot use all of iwlagn because
the size of the RX buffer is different. Revert back to using
iwl3945 specific routines that map/unmap memory.
- no need to "dma_syn_single_range_for_cpu" followed by pci_unmap_single,
we can just call pci_unmap_single initially
- only map the memory area that will be used by device. this is especially
relevant to the mapping of iwl_cmd. we should not map the entire
structure because the meta data at the beginning of structure contains
the address to be used later for unmapping. If the address to be used for
unmapping is stored in mapped data it creates a problem.
- ensure that _if_ memory needs to be modified after it is mapped that we
call _sync_single_for_cpu first, and then release it back to device with
_sync_single_for_device
- we mapped the wrong length of data for host commands, with mapped length
differing with length provided to device, fix that.
Thanks to Jason Andryuk <jandryuk@gmail.com> for significant bisecting
help to find these issues.
This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1964
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Tested-by: Ben Gamari <bgamari@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugging TX issues it is helpful to know the seq nr of the
frame being transmitted. The seq nr is printed as part of ucode's
log informing us which frame is being processed. Having this information
printed in driver log makes it easy to match activities between driver
and firmware.
Also make possible to print TX flags directly. These are already printed
as part of entire TX command, but having it printed directly in cpu format
makes it easier to look at.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a build warning in mwl8.c.
(Marvell TOPDOG wireless driver)
The warning it fixes is: "large integer implicitly truncated to unsigned type."
The rx_ctrl member of the mwl8k_rx_desc struct is 8 bit (__u8 ), whereas trying
to assign it a 32 bit value (which is returned from cpu_to_le32())
causes the compiler to issue
a truncation warning.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users reported lockup with work still trying to run
after module has been unloaded.
http://thread.gmane.org/gmane.linux.kernel.wireless.general/30594/focus=30601
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: TJ <ubuntu@tjworld.net>
Reported-by: Huaxu Wan <huaxu.wan@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the bug where some revisions of 6000 series hardware cannot
be used. Later versions of 6000 series have the EEPROM replaced by
OTP. For these devices to be used we need to expand valid EEPROM mask.
Signed-off-by: Jay Sternberg <jay.e.sternberg@linux.intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
`!' has a higher precedence than `&', parentheses are misplaced.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Error found by Jeff Haran.
The error detect register is 0s when no errors are detected. The check
code is incorrect, so reverse check sense.
Reported-by: Jeff Haran <jharan@Brocade.COM>
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Doug Thompson <dougthompson@xmission.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For an upcoming distro release, we need to have the xp kernel module
loadable even when not on UV equipment. The xpc module will not load.
This will allow one set of modules dependent upon xp to work on either UV
or non-UV equipment.
Signed-off-by: Robin Holt <holt@sgi.com>
Signed-off-by: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With no IRQ available/defined, RTC-CMOS driver prints something like:
rtc0: alarms up to one no, y3k, 114 bytes nvram
^^^^
I guess the following is a bit easier to understand:
rtc0: no alarms, y3k, 114 bytes nvram
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On line 944 the return value of flush() is considered as a boolean,
but limit reaches -1 upon timeout which evaluates to true.
On 540, 594, 720 the same occurs for wait_ssp_rx_stall()
On 536 the same occurs for wait_dma_channel_stop()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If DMA is enabled, any spi_sync call after suspend/resume would block
forever, because DRCMR is lost on suspend. This patch restores DRCMR to
the same values set by probe.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On parisc machines, which don't have HIL, removing the hp_sdc module
panics the kernel. Fix this by returning early in hp_sdc_exit() if no HP
SDC controller was found.
Add functionality to probe for the hp_sdc_mlc kernel module (which takes
care of the upper layer HIL functionality on parisc) after two seconds.
This is needed to get all the other HIL drivers (keyboard / mouse/ ..)
drivers automatically loaded by udev later as well.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Frans Pop <elendil@planet.nl>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enable userspace to receive messages that a BMC transmits using an OEM
medium. This is used by the HP iLO2.
Based on code originally written by Patrick Schoeller.
Signed-off-by: dann frazier <dannf@hp.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bela Lubkin noticed that the statistics for send IPMB and LAN commands
in the IPMI driver could be incremented even if an error occurred. Move
the increments to the proper place to avoid this.
Also add some statistics for retransmissions that failed, and some little
helper functions to neaten up the code a little.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Bela Lubkin <blubkin@vmware.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The IPMI driver would attempt to use the event buffer even if that
didn't exist on the BMC. This patch modified the IPMI driver to check
for the event buffer's existence before trying to use it.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The wrong return value is being tested when allocating a platform device
in the IPMI SI code. Check the right value.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes the warning:
drivers/video/pxafb.c: In function 'pxafb_handle_irq':
drivers/video/pxafb.c:1442: warning: unused variable 'lcsr1'
[akpm@linux-foundation.org: save an ifdef]
Signed-off-by: Denis V. Lunev <den@openvz.org>
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 032220ba (asiliantfb: fix cmap memory leaks) changed the function
init_asiliant from void to int, resulting in the following compile warning:
drivers/video/asiliantfb.c: In function `init_asiliant':
drivers/video/asiliantfb.c:536: warning: control reaches end of non-void function
Fix the warning by returning 0.
Signed-off-by: Vlada Peric <vlada.peric@gmail.com>
Cc: Andres Salomon <dilinger@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the go7007 driver away from the legacy i2c binding model, which
is going away really soon now.
The I2C addresses of the audio and video chips in s2250-board didn't
look quite right, apparently they were left-aligned values when Linux
wants right-aligned values, so I fixed them too.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
sparse says:
drivers/net/wireless/atmel.c:1501:3: warning: Initializer entry defined twice
drivers/net/wireless/atmel.c:1505:3: also defined here
and it's correct; atmel has its own ndo_change_mtu and
shouldn't use eth_change_mtu.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs: add cis(firmware) of the Allied Telesis LA-PCM
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If creating a workqueue fails, don't jump to the error path where that
same workqueue is destroyed, since destroy_workqueue() can't handle a
NULL pointer.
This was spotted by the Coverity checker (CID 2617).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per ring counters are implemented in SW. Now moving to have the total
counters as the sum of all rings. This way the numbers will always be consistent
and we no longer depend on HW buffer size limitations for those counters
that can be insufficient in some cases.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The former usage was to set the NETIF_F_HW_CSUM flag which is not used
in get_tx_csum. It caused Ethtool to show tx checksum as "on" even
though it was turned off in previous operation.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The low level driver always assumes this handler exists.
The lack of it could cause kernel panic
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The query whether the port is up or not should be done at
the execution of the restart task and not when it is queued.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of failure of either srq creation or page allocation,
the cleanup code handled the failed ring as well, and tried
to destroy resources that where not allocated.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent NVRAM patches sanitized how the driver deals with NVRAM
data, but they failed to bring the SEEPROM interfaces inline with
the new strategy. This patch brings the SEEPROM interfaces up to date.
This patch also reverts commit 0d489ffb76
("tg3: fix big endian MAC address collection failure").
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Tested-by: Robin Holt <holt@sgi.com>
Tested-by: James Bottomley <james.bottomley@HansenPartnership.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a hang on resume when the filesystem is not
available and request_firmware blocks.
However, the device does not accept the firmware on resume.
and it will exit with:
> firmware part 1 upload failed (-71).
> device is in a bad state. please reconnect it!
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
swap mwl8k_remove and mwl8k_shutdown functions to allow
"rmmod mwl8k; modprobe mwl8k"
Signed-off-by: Joerg Albert <jal2@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch deactivates powersave in station mode.
It does not work correctly yet, so the code does more harm than good.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After suspend & resume the rt2x00 devices won't wakeup
anymore due to a broken register information setup.
The most important problem is the release of the EEPROM
buffer which is completely cleared and never read again
after the suspend.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
agp: zero pages before sending to userspace
drm: check for minor master before allowing drop master.
drm: set/clear is_master when master changed
drm: clean dirty memory after device release
drm: count reaches -1
* 'for-linus' of git://neil.brown.name/md:
md: support bitmaps on RAID10 arrays larger then 2 terabytes
md: update sync_completed and reshape_position even more often.
md: improve usefulness and accuracy of sysfs file md/sync_completed.
md: allow setting newly added device to 'in_sync' via sysfs.
md: tiny md.h cleanups
notice one system /proc/iomem some entries missed the name for pci_devices
it turns that dev->dev.kobj name is changed after device_add.
for pci code: via acpi_pci_root_driver.ops.add (aka acpi_pci_root_add)
==> pci_acpi_scan_root is used to scan pci bus/device, and at the same
time we read the resource for pci_dev in the pci_read_bases, we have
res->name = pci_name(pci_dev); pci_name is calling dev_name.
later via acpi_pci_root_driver.ops.start (aka acpi_pci_root_start) ==>
pci_bus_add_device to add all pci_dev in kobj tree. pci_bus_add_device
will call device_add.
actually in device_add
/* first, register with generic layer. */
error = kobject_add(&dev->kobj, dev->kobj.parent, "%s", dev_name(dev));
if (error)
goto Error;
will get one new name for that kobj, old name is freed.
[Impact: fix corrupted names in /proc/iomem ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the sk_sleep wait queue actually lives in tfile, which may be
detached from the tun device, bad things will happen when we use
sk_sleep after detaching.
Since the tun device is the persistent data structure here (when
requested by the user), it makes much more sense to have the wait
queue live there. There is no reason to have it in tfile at all
since the only time we can wait is if we have a tun attached.
In fact we already have a wait queue in tun_struct, so we might
as well use it.
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Tested-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit c70f182940 ("tun: Fix
races between tun_net_close and free_netdev") fixed a race where
an asynchronous deletion of a tun device can hose a poll(2) on
a tun fd attached to that device.
However, this came at the cost of moving the tun wait queue into
the tun file data structure. The problem with this is that it
imposes restrictions on when and where the tun device can access
the wait queue since the tun file may change at any time due to
detaching and reattaching.
In particular, now that we need to use the wait queue on the
receive path it becomes difficult to properly synchronise this
with the detachment of the tun device.
This patch solves the original race in a different way. Since
the race is only because the underlying memory gets freed, we
can prevent it simply by ensuring that we don't do that until
all tun descriptors ever attached to the device (even if they
have since be detached because they may still be sitting in poll)
have been closed.
This is done by using reference counting the attached tun file
descriptors. The refcount in tun->sk has been reappropriated
for this purpose since it was already being used for that, albeit
from the opposite angle.
Note that we no longer zero tfile->tun since tun_get will return
NULL anyway after the refcount on tfile hits zero. Instead it
represents whether this device has ever been attached to a device.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEH attempts to recover up 6 times.
The last attempt leaves all the ports and adapter down.hen
The driver is then unloaded, bringing the adapter down again
unconditionally. The unload will hang.
Check if the adapter is already down before trying to bring it down again.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fatal error task can be scheduled while processing an offload packet
in NAPI context when the connection handle is bogus. this can race
with the ports being brought down and the cxgb3 workqueue being flushed.
Stop napi processing before flushing the work queue.
The ULP drivers (iSCSI, iWARP) might also schedule a task on keventd_wk
while releasing a connection handle (cxgb3_offload.c::cxgb3_queue_tid_release()).
The driver however does not flush any work on keventd_wq while being unloaded.
This patch also fixes this.
Also call cancel_delayed_work_sync in place of the the deprecated
cancel_rearming_delayed_workqueue.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing periodic task to handle link faults.
The link fault interrupt handler is also called in work queue context,
which is wrong and might cause potential deadlocks.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when the brightness level on AC and brightness level on Battery
are same, the level_ac_battery is 1 in the current code,
which is wrong.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
.. and other arrays with components larger than 2 terabytes.
We use a "long" rather than a "sector_t" in part of the bitmap
size calculations, which is sad.
Reported-by: "Mario 'BitKoenig' Holbe" <Mario.Holbe@TU-Ilmenau.DE>
Signed-off-by: NeilBrown <neilb@suse.de>
AGP pages might be mapped into userspace finally, so the pages should be
set to zero before userspace can use it. Otherwise there is potential
information leakage.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When fast user switching a lot eventually we get to the point,
where we were checking for the wrong thing in this function.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The variable is_master is being used to track the drm_file that is currently
master, so its value needs to be updated accordingly when the master is
changed.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In current code we register/unregister connector object by
drm_sysfs_connector_add/remove function.
However under some cases, we need to dynamically register or unregister device
multiple times, so we have to go through register -> unregister ->register
routine.
Because after device_unregister function our memory is dirty, we need to do
clean operation in order to re-register the device, otherwise the system
will crash. The patch intends to clean device after device release.
Signed-off-by: Ma Ling <ling.ma@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With a postfix decrement in the test count will reach -1 rather than 0,
subsequent tests fail.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 900af0d973 (PM: Change suspend
code ordering) changed the ordering of suspend code in such a way
that the platform .prepare() callback is now executed after the
device drivers' late suspend callbacks have run. Unfortunately, this
turns out to break ARM platforms that need to talk via I2C to power
control devices during the .prepare() callback.
For this reason introduce two new platform suspend callbacks,
.prepare_late() and .wake(), that will be called just prior to
disabling non-boot CPUs and right after bringing them back on line,
respectively, and use them instead of .prepare() and .finish() for
ACPI suspend. Make the PM core execute the .prepare() and .finish()
platform suspend callbacks where they were executed previously (that
is, right after calling the regular suspend methods provided by
device drivers and right before executing their regular resume
methods, respectively).
It is not necessary to make analogous changes to the hibernation
code and data structures at the moment, because they are only used
by ACPI platforms.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Len Brown <len.brown@intel.com>
This reverts commit 1c55f18717.
Ingo Brueckl was assuming that reverting to 1:1 mapping for chars >= 128
was not useful, but it happens to be: due to the limitations of the
Linux console, when a blind user wants to read BIG5 on it, he has no
other way than loading a font without SFM and let the 1:1 mapping permit
the screen reader to get the BIG5 encoding.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Break out of wait_event_interruptible() if freezing has been requested,
in the vballoon thread. Without this change vballoon refuses to stop and
the system can't suspend.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org
Fixes guest crash 'lguest: bad read address 0x4800000 len 256'
The new per-cpu allocator ends up handing a non-linear address to
write_gdt_entry. We do __pa() on it, and hand it to the host, which
kills us.
I've long wanted to make the hypercall "LOAD_GDT_ENTRY" to match the IDT
code, but had no pressing reason until now.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: lguest@ozlabs.org
Typical message: 'lguest: unhandled trap 6 at 0x418726 (0x0)'
vmlinux guests were broken by 4cd8b5e2a1
'lguest: use KVM hypercalls', which rewrites guest text from kvm hypercalls
to trap 31.
The Launcher mmaps the kernel image. The Guest executes and
immediately faults in the first text page (read-only). Then it hits a
hypercall, and we rewrite that hypercall, causing a copy-on-write.
But the Guest pagetables still refer to the old page: we fault again,
but as Host we see the hypercall already rewritten, and pass the fault
back to the Guest. The Guest hasn't set up an IDT yet, so we kill it.
This doesn't happen with bzImages: they unpack themselves and so the
text pages are already read-write.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Patrick McHardy <kaber@trash.net>
The driver somehow got merged with the initializer for the dma_sff_read_status()
method missing which caused kernel panic on bootup.
This should fix the kernel.org bug #13026...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Reported-by: Arnd Hannemann <hannemann@nets.rwth-aachen.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Freeing non-slab objects is bad and results in an oops. Fix it.
Reported-and-tested-by: Andrew Price <andy@andrewprice.me.uk>
Cc: Theodore Tso <tytso@mit.edu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove uneeded void casts
Signed-off-by: Jack Stone <jwjstone@fastmail.fm>
Cc: jeff@garzik.org
Cc: kernel-janitors@vger.kernel.org
Cc: Jack Stone <jwjstone@fastmail.fm>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Use ATA_DMA_* constants instead of the bare numbers for the BMIDE register bits.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The big driver change in 2.4.19-rc1 introduced a regression for many HPT370[A]
chips -- DMA stopped to work completely, only causing endless timeouts...
The culprit has been identified (at last!): it turned to be the code resetting
the DMA state machine before each transfer. Stop doing it now as this counter-
measure has clearly caused more harm than good.
This should fix the kernel.org bug #7703.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
