When reading flags, bq27x00_read() argument is inverted and causes
reads 2 of bytes for bq27200 and 1 byte for bq27500, while their register
sizes are 1 and 2 bytes respectively. This causes bq27500 upper flag
bits always to be returned as 0, causing full charge state to never be
reported correctly, so fix it.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
This reverts commit 270968c098.
Grazvydas Ignotas wrote:
After 270968c098 "bq27x00_battery: Fix reporting status value for
bq27500 battery" status doesn't seem to be reported correctly when the
battery is close to fully charged state. It reports "Not charging"
while in fact there is >130mA current flowing to the battery according
to current_now.
This status report seems to be based on CHG bit in status register,
but looking at the datasheet the description says "(Fast) charging
allowed", which I guess means that the chip recommends charging and
not that charging is actually going on? If you check the bit while
battery is discharging and it's not full, the bit is also set.
Suggested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* power_supply_unregister call bq27x00_battery_get_property which
call bq27x00_battery_poll
* make sure that bq27x00_battery_poll will not call
schedule_delayed_work again after unregister (which cause OOPS)
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* Do not be noise if battery is not calibrated (use dev_dbg)
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* CI (Capacity Inaccurate) flag is set after full reset on bq27000 battery
* when is set, all capacity properties should be reported incorrectly,
because there was no learning cycle and battery was not calibrated
* instead reporting incorrect values, report -ENODATA
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
* This prevent reporting old current_now value for bq27000
* Also ask for current flags, to make sure that current_now
will be reported with correct signature
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Doing this by using 2 calls sometimes results in unexpected
values being returned on OMAP3 i2c controller.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
* Consistently use uppercase for hexadecimal values.
* Clarify/fix the unit of functions return value in its comment.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
The current code only reports whether the battery is charging or
discharging. But the battery also reports whether it is fully charged,
furthermore by look at if the battery is supplied we can tell whether it
is discharging or not charging.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds support for polling the battery state and generating a
power_supply_changed() event if it has changed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds a register cache to the bq27x00 battery driver.
Usually multiple, if not all, power_supply properties are queried at once,
for example when an uevent is generated. Since some registers are used by
multiple properties caching the registers should reduce the number of
reads.
The cache is valid for 5 seconds this roughly matches the internal update
interval of the current register for the bq27000/bq27200.
Fast changing properties(*_NOW) which can be obtained by reading a single
register are not cached.
It will also be used in the follow up patch to check if the battery status
has been changed since the last update to emit power_supply_changed events.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds support for the bq27000 battery to the bq27x00 driver.
The bq27000 is similar to the bq27200 except that it uses the HDQ bus
instead of I2C to communicate with the host system.
The driver is implemented as a platform driver. The driver expects to be
provided with a read callback function through its platform data. The read
function is assumed to do the lowlevel HDQ handling and read out the value
of a certain register.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch simplifies the drivers data structure and moves code to be
shared by the bq27000 and bq27200/bq27500 init functions into a common
function.
This patch has no functional changes, it only moves code around.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch changes get_property callback of the bq27x00 battery to return
-ENODEV for properties other then the PROP_PRESENT if the battery is not
present.
The power subsystem core expects a driver to behave that way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
According to the bq27000 datasheet the current should be calculated by
the following formula:
current = AI * 3570 / 20
This patch adjust the drivers code accordingly.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch improves the precession of the temperature property of the
bq27x00 driver.
By dividing before multiplying the current code effectively cuts of the
last decimal digit. This patch fixes it by multiplying before dividing.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
This patch adds the type property to the bq27x00 battery driver.
All bq27x00 are lithium ion batteries.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The chip returns voltage and current in mV and mA, but
power supply class uses uV and uA, so add missing conversion.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The BQ27x00 series of chips can report time-to-empty and
time-to-full, so let's add corresponding properties.
Also report charge status based on status flag register.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
BQ27500 is newer fuel gauge chip from TI with slightly changed
register layout and some different register semantics. Add new i2c
ID for it and handle differences where needed. Also rename bq27200
functions to bq27x00, as they are no longer bq27200 specific.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The power supply class requires tenths of degree Celsius.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
These are probably leftover from old TI code.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The bq27x00 registers are little endian, so just read them as such
and don't do double endian swap on LE machines.
This also gets rid of strange looking shift that was done after
reading 8bit register because endian swap in bq27x00_read() was
messing it up.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
A few comments say "Celcius"; this fixes them. No code changes.
Signed-off-by: Adam Buchbinder <adam.buchbinder@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Remove hand-rolled get_unaligned_be16, this points to a possible bug as
bq27x00_read does another endian byteswap which sparse notices:
drivers/power/bq27x00_battery.c:81:14: warning: cast to restricted __be16
Which should probably be checked.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
These battery managers came in two different packages: one for I2C
busses (BQ27200) and one for HDQ busses (BQ27000).
This driver currently supports only the I2C chip version but the code
is designed in order to easily allow the HDQ chip version integration.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: make things static, use kasprintf()]
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
