Improve error message reporting when a frame was received
with unknown rate. Instead of using the boolean check if
the frame is supposed to be a PLCP value or not, we should
add a new mask (RXDONE_SIGNAL_MASK) which returns the type
identification for a signal value (i.e. PLCP). At the moment
we only have 2 different types, but more will arrive when
support for 11n is added.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag ENTRY_TXD_OFDM_RATE isn't flexible enough
to indicate which rate modulation should be used for
a frame. This will become a problem when 11n support
is added.
Remove the flag and replace it with an enum value which
can better indicate the exact rate modulation.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some functions have grown rapidly in size over the last time,
some of those functions (like the rt2x00queue_create_tx_descriptor)
will further increase in size soon, so it is best to start cutting
it into logical pieces.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 2 bits in EEPROM_NIC_TX_RX_FIXED each influence
a different antenna. We might as well split the
definition and directly read the correct bit.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
WDS support should be very easy to handle, mac80211 handles
everything for us, so all that is needed is to set the
support flags and handle it in the add_interface() callback.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_CRYPTO_COPY_IV is a bad name since it is part
of the driver requirements instead of a configuration option.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some very rare Ralink USB hardware exists which features
the RFKILL switch on the USB stick.
This patch adds the EEPROM check function to see if RFKILL
is supported and the polling function to rt2500usb and
rt73usb in order to support RFKILL for that hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds initial support for Mesh Point mode. For this we tell mac80211 that
we support NL80211_IFTYPE_MESH_POINT. We also need to send beacons. mac80211
will configure our RX filter accordingly.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restrict drivers to only access link_qual structure during
link tuning. The contents of these fields are for the drivers
and all fields are allowed to be changed to values the driver
considers correct.
This means that some fields need to be moved outside of this
structure to restrict access only to rt2x00link itself.
This allows some code to be moved outside of the rt2x00.h header
and into rt2x00link.c.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The link_tuner() function will always call bbp_read()
at the start of the function. Because this is an
indirect register access has some costs attached
to it (especially for USB hardware).
We already store the value read from the register
into the vgc_level value inside the link structure.
Instead of reading from the register we can read that
field directly and base the tuner on that value.
This reduces the time the registers are locked with
the csr_mutex and speeds up the link_tuner processing.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move link and antenna tuning into a seperate file named rt2x00link.c,
this makes the interface to the link tuner a lot cleaner.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Listen to IEEE80211_CONF_PS to determine if the device
should drop into powersaving mode. This feature depends
on the dynamic power save functionality in mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mac80211 provides 2 structures to handle bitrates, namely
ieee80211_rate and ieee80211_tx_rate. To determine the short preamble
mode for an outgoing frame, the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE
must be checked on ieee80211_tx_rate and not ieee80211_rate (which rt2x00 did).
This fixes a regression which was triggered in 2.6.29-rcX as reported by Chris Clayton.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-By: Chris Clayton <chris2553@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running modprobe rt73usb, and then rmmod rt73usb, and then
iwconfig, the wlan0 device does not disappear. When repeating this
process again, we get a kernel Oops errors and "BUG: unable to handle
kernel paging request..." message in the kernel log.
The reason for this is that there is an error in rt2x00rfkill_free(),
which is called in the process of removing the device
(rt2x00lib_remove_dev() in rt2x00dev.c).
rt2x00rfkill_free() clears the RFKILL_STATE_ALLOCATED bit , which is
bit number 1 () in rt2x00dev->flags instead of in
rt2x00dev->rfkill_state. As a result, when checking the
DEVICE_STATE_REGISTERED_HW bit (bit number 1 in rt2x00dev->flags) in
rt2x00lib_remove_hw() it is **unset**, and we wrongly **don't** call
ieee80211_unregister_hw().
This patch corrects this: the parameter for __test_and_clear_bit() in
rt2x00rfkill_free() should be &rt2x00dev->rfkill_state and not
&rt2x00dev->flags.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TXD_W0_CIPHER field is a 1-bit field. It only acts as boolean value
to indicate if the frame must be encrypted or not.
The way rt2x00_set_field32() worked it would grab the least signifcant bit
from txdesc->cipher and use that as value. Because of that WEP 64 and TKIP
worked since they had odd-numbered values, while WEP 128 and AES were
even numbers and didn't work.
Correctly booleanize the txdecs->cipher value to allow the hardware to
encrypt the outgoing data. After this we can enable HW crypto by default again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb doesn't strip the IV/ICV data from received frames,
so we don't need to set the RX_FLAG_IV_STRIPPED flag.
We do need to set the RX_FLAG_MMIC_STRIPPED flag for all
encryption types since the MMIC has been removed from the frame.
After this patch TKIP Hardware crypto works for rt2500usb.
WEP and AES are still failing.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue_end() macro points to 1 position after the
queue, which means that if we want to know if queue
is at the end of the queue we should first increment
the position and then check if it is a valid entry.
This fixes a segmentation fault which only occurs when
the device has enough endpoints to provide a dedicated
endpoint for all TX queues (which likely won't happen
for rt2500usb and rt73usb, but will happen for rt2800usb).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The short preamble mode was not correctly detected during TX,
rt2x00 used the rate->hw_value_short field but mac80211 is not
using this field that way.
Instead the flag IEEE80211_TX_RC_USE_SHORT_PREAMBLE should be
used to determine if the frame should be send out using
short preamble or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add USB ID for the Linksys WUSB200 Wireless-G Business USB Adapter to
rt73usb.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since "rt2x00: Fix LED state handling", rt2x00leds_led_radio wrongly
checks that the LED type is LED_TYPE_ASSOC. This patch makes it check
for LED_TYPE_RADIO once again.
Signed-off-by: Andrew Price <andy@andrewprice.me.uk>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Request the AID from hardware and provide this id
to the driver (in case they need it).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all code which determines the right TX descriptor
fields specific to crypto support into rt2x00crypto.c.
This makes the code in rt2x00queue more simpler and
better concentrates all crypto code into a single location.
With this we can also remove some ifdefs in rt2x00queue.c
since the code inside the ifdef is either very small, or
only calling empty functions (see empty function definitions
in rt2x00lib.h).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix ERP configuration, due to a too strict changes
flags checking we never updated the short slot time
or basic rate mask when no other changes were made
at the same time.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers should notify rt2x00lib when they provide
the IV/ICV data. This adds some flexibility to drivers
which can't provide all information.
* rt2500usb provides ICV inside the frame
* rt2800pci doesn't provide IV/ICV
* rt2800usb doesn't provide IV/ICV
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb supports hardware encryption.
rt2500usb supports up to 4 shared and pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simplify rt2x00lib_config_antenna() by moving
duplicate code into a seperate static inlined
function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Store retry limit values in the rt2x00dev structure.
This allows the removal of the FIXME where we assumed
the long retry is only used when working with RTS frames.
Instead we should check the current retry limit values
and decide if the required retry count for this frame
is a long or short retry.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IV and EIV belong to eachother and don't require
2 seperate fields. Instead they can logically be
merged into a single array with size 2.
With this approach we can simplify the code in
rt2x00crypto.c by using a single memcpy() when
copying the iv/eiv data. Additionally we can
move some code out of if-statements because the
if-statement would always be true.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we switch off the LEDS during initialization
we kill rt73usb from proper functioning. The immediate
result after the first LED command are MCU failures
and a complete breakdown of TX/RX.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the used in/out endpoints
we should detect them by walking through all
available endpoints.
rt2800usb will gain the most out of this, because
the legacy drivers indicate that there are multiple
endpoints available.
However this code might benefit at least rt73usb as
well for the MIMO queues, and if we are really lucky
rt2500usb will benefit because for the TX and PRIO
queues.
Even if rt2500usb and rt73usb do not get better performance
after this patch, the endpoint detection still belongs to
rt2x00usb, and it shouldn't hurt to always try to detect
the available endpoints.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback function write_tx_data() can only fail
when our ENTRY_OWNER_DEVICE_DATA flag on a queue entry
failed to determine the entry was not available and
it is in fact still owned by the hardware.
This means that if that function fails the queue
must be stopped in mac80211.
When rt2x00queue_get_queue() returns NULL in the TX
path, it means mac80211 has passed us an invalid queue,
although this should be impossible, it shouldn't hurt
if we send mac80211 a signal to stop the queue either.
Both issues can simply be resolved by removing their
manual failure handler and making them use the failure path
provided in rt2x00mac_tx().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb and rt73usb have different register word sizes,
for that reason the register access wrappers were never
moved into rt2x00usb.
With rt2800usb on its way, we should favor the 32bit
register access and move those wrappers into rt2x00usb.
That saves duplicate code, since only rt2500usb will
need the special 16bit wrappers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All code which accessed indirect registers was similar
in respect to the for-loop, the given timeout, etc.
Move it into a seperate function, which for PCI drivers
can be moved into rt2x00pci.
This allows us to cleanup the cleanup the code further
by removing the goto statementsand making the codepath
look a bit nicer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Indirect registers require multiple calls to the CSR
register in order to access the indirect registers.
This must be protected under a lock to prevent race
conditions which could cause invalid data to
be returned when reading from the indirect register or silent
failures when writing data to the indirect register.
USB drivers where already protected under a mutex,
so rename the mutex and make PCI drivers use the mutex
as well.
This now means that BBP and RF registers are no longer
accessible in interrupt context. That is not a bad
situation since the slow behavior of accessing
those registers means we don't _want_ to access them
in interrupt context either.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can optimize get_duration and get_duration_res
by making them a macro. They are really simple
calculation handlers so this doesn't matter much.
Often (especially in rt2400pci and rt2500pci,
the arguments are hardcoded, and the result value
is passed into other hardcoded values.
By making the functions a macro GCC can
optimize the entire thing much better.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge the callback functions init_txentry() and
init_rxentry(). This makes life in rt2x00lib a
lot simpler and we can cleanup several functions.
rt2x00pci contained "fake" FIELD definitions for
descriptor words. This is not flexible since it
assumes the driver will always have the same field
to indicate if a driver is available or not.
This should be dependent on the driver, and we
should add a callback function for this.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new configuration handling, and more specifically
splitting the configuration of the antenna from the normal
configuration steps allowed a BUG_ON() to be triggered
in the driver because the SW_DIVERSITY was send to the
driver. This fixes that by catching the value early in
rt2x00config.c and replacing it with a sensible value.
This also fixes a problem where the antenna is not being
initialized at all when the radio is enabled. Since it
no longer is part of the mac80211 configuration the
only place where rt2x00 configured it was the SW diversity
handler. Obviously this is broken for all non-diversity
hardware and breaks SW diversity due to a broken initialization.
When the radio is enabled the antenna will be configured
once as soon as the config() callback function is called.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will call set_key() when the device is
shutting down. When the device is unplugged the
keys will be lost automatically due to the power
loss. When the device is not plugged but the module
is only unloaded the keys can remain in the device
hardware, when the module is loaded the keys will
be cleaned up during initialization.
This should prevent the problem reported by Johannes Berg,
where unplugging the device while suspended resulted in
a NULL pointer error during set_key() which was
caused because of the CSR base address being freed.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For every global LED state change (register/unregister,
suspend/resume) we should force the LEDS to turn off.
This makes sure that the LEDS will always be in a sane
state after the state switch.
Note that when unregister is called but the LED class
wasn't resumed yet, we shouldn't change the LED state
since we might not have access to the device (device
was unplugged while suspended).
Also remove the checks in the activity, assoc and
radio LEDS which blocked calls to brightness_set()
when the state hasn't changed. Some of those LEDS
could be enabled by themselves when something happens
in the hardware (e.g. firmware is loaded). We already
did called rt2x00leds to switch the LED off, but those
calls were blocked.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 is in charge of determining the basic rates,
so we are not using the RATE_BASIC flag anymore.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move calculation of CSR register offset into rt2x00debug.c
and remove the wrapper functions from each individual driver.
(Except rt2500usb, which still needs to wrap for the
different value type argument).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All operating modes which require beaconing should
depend on the availability of beacon entries from
the hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can safely remove ieee80211_bss_conf from rt2x00_intf,
it is provided by mac80211 in ieee80211_vif as well.
(rt2x00_intf is the drv_priv field of ieee80211_vif).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement latest changed from mac80211 configuration
handling to optmize configuration handling in rt2x00.
* Remove set_retry_limit callback function, handled
through config()
* Move config_antenna to its own callback function,
it isn't handled by mac80211 anymore
* Use IEEE80211_CONF_CHANGED_* flags and remove manual
checks
* Removed deprecated short slot setting through config()
and put it in config_erp() through which mac80211 now
configures it
* Remove config_phymode() and move contents to config_erp()
since it only managed the basic rates which is now
determined by mac80211 through config_erp().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs_create_*() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few changes to reduce checkpatch.pl errors in the rt2x00 driver. For
the most part, I only fixed cosmetic things, and left the actual 'code
flow' untouched (hopefully)!
Diff is against wireless-testing HEAD.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced pci_ioremap_bar() function in drivers/net.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make menuconfig RT2X00 a tristate instead of boolean,
otherwise we do not correctly inherit the mac80211 value
on which RT2X00 depends, and makes it possible to
compile rt2x00 into the kernel while mac80211 is a
module.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.
I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hw_key pointer is used (and obviously NULL) after skb->cb is
memset to 0. This patch grabs the iv_len before the memset call.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Free up 2 bytes in skb->cb to be used for multi-rate retry later.
Move iv_len and icv_len initialization into key alloc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The state field of the rfkill structure was incorrectly initialized to -1, which results in rfkill
issueing a WARN_ON. Fix this by initializing the state field to the proper value as indicated by
the driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix by disabling rt2x00 rfkill support when rt2x00 is built-in and rfkill has been modularized, and
a similar scheme for the relationship between leds_class and rt2x00..
Also, give a warning to the end-user when rfkill-/leds-support is disabled this way, so that the
end-user has at least some clues on what is going on.
Proper fixing required some general updates of the Kconfig-structure for the rt2x00 driver, whereby
internal configuration symbols had to be moved to after the user-visible configuration symbols.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a crypto key is being removed, rt2x00mac should not
reset the key->hw_key_idx value because that will prevent
the driver from removing the correct key from the hardware.
Furthermore ffz() starts counting at 0 instead of 1, so we don't
need to substract 1 from the resulting value.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, virtual interface pointers passed to drivers might be
from monitor interfaces and as such completely uninitialised
because we do not tell the driver about monitor interfaces when
those are created. Instead of passing them, we should therefore
indicate to the driver that there is no information; do that by
passing a NULL value and adjust drivers to cope with it.
As a result, some mac80211 API functions also need to cope with
a NULL vif pointer so drivers can still call them unconditionally.
Also, when injecting frames we really don't want to pass NULL all
the time, if we know we are the source address of a frame and have
a local interface for that address, we can to use that interface.
This also helps with processing the frame correctly for that
interface which will help the 802.11w implementation. It's not
entirely correct for VLANs or WDS interfaces because there the MAC
address isn't unique, but it's already a lot better than what we
do now.
Finally, when injecting without a matching local interface, don't
assign sequence numbers at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There isn't really a good reason to have the LED
configuration options selectable per driver, lets
make it default 'y' and make it depend on the
NEW_LEDS and LEDS_CLASS interface.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RFKILL should be enabled for _all_ hardware whether
or not they feature a rfkill button or not.
Remove driver specific RFKILL configuration options
and make the rt2x00lib version depend on CONFIG_RFKILL
and defaulting to 'y' to make sure it will always
be enabled when RFKILL was enabled.
This also fixes some bugs where RFKILL wasn't initialized
and didn't respond to RFKILL key presses.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts:
b93ce437eb
rt2x00: Fix the beacon length bug
The workaround is no longer required since it has been
correctly fixed in rt2x00usb now.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is obviously good for userspace to know up front which
interface modes a given piece of hardware might support (even
if adding such an interface might fail later because of
concurrency issues), so let's make cfg80211 aware of that.
For good measure, disallow adding interfaces in all other
modes so drivers don't forget to announce support for one mode
when they add it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A "Set" to a sign-bit in an "&" operation causes a compiler warning.
Make calculations unsigned.
[ The warning was masked by the old definition of BUILD_BUG_ON() ]
Also remove __builtin_constant_p from FIELD_CHECK since BUILD_BUG_ON
no longer permits non-const values.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
CC: Ingo Molnar <mingo@elte.hu>
CC: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure the skb->data pointer points to the frame data, not the TX
descriptor. The frame dumping code relies on that.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the PLCP flag to indicate if the
signal value is plcp or the bitrate we should add
a new flag to mark the bitrate type explicitely.
This is usefull when new types are added later for
rt2800.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The txop parameter is supported by rt61pci and rt73usb,
and thus should be written to the register instead
of using the fixed value set during initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware configuration registers such as antenna and channel configuration
can only be written when the radio is enabled. Previously, we didn't consider
this, so some configuration items could be set inconsistently after reenabling
the radio. This patch changes the config() handler to only reprogram the
hardware when the radio is enabled. Configuration changes that are made while
the radio is off are postponed until the radio is switched back on. We also
leave the radio turned off during initialization and only enable it when
requested by mac80211. This allows us to get rid of the DIRTY_CONFIG flag,
because the device is now guaranteed to be completely initialized when brought
up by mac80211.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a driver requests additional headroom it should
be mapped to DMA as well because it will be send to
the hardware as well (as form of extra descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the flags should be accessed atomically to
prevent race conditions. The flags that are most important
are those that can change often and indicate the actual
state of the device, queue or queue entry.
The big flag rename was done to move all state flags to
the same naming type as the other rt2x00dev flags and
made sure all places where the flags were used were changed. ;)
Thanks to Stephen for most of the queue flags updates,
which fixes some of the most obvious consequences of the
race conditions. Among those the notorious:
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a module parameter to rt61 and rt73 to disable
HW crypto. The option should only be checked when
determining if the SUPPORT_HW_CRYPTO flag should
be set or not.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can optimize lna calculation in IRQ context by
calculating most of the value during the config() callback
when most of the value is actually influenced.
This will be required later by rt2800pci and rt2800usb as
well, since they need the lna_gain value during config().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Channel information which is read from EEPROM should
be read into an array containing per-channel information.
This removes the requirement of multiple arrays and makes
the channel handling a bit cleaner and easier to expand.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb supports hardware encryption.
rt73usb supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt61pci supports hardware encryption.
rt61pci supports up to 4 shared keys and up to 64 pairwise keys.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various rt2x00 devices support hardware encryption.
Most of them require the IV/EIV to be generated by mac80211,
but require it to be provided seperately instead of within
the frame itself. This means that rt2x00lib should extract
the data from the frame and place it in the frame descriptor.
During RX the IV/EIV is provided in the descriptor by the
hardware which means that it should be inserted into the
frame by rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not allowed to use NETDEV_TX_BUSY in tx path anymore.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txdone_entry_desc_flags is used with __set_bit and test_bit which
bit-shift the values, so don't bit-shift the flags in the enum.
Also make sure flags are initialized before being used.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It was possible for unsupported operating modes
to be accepted by the add_interface callback function.
This patch will block those modes until proper support
has been implemented for them.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the legacy rt2570 driver the link tuner was never
really called. And now the reason has finally become
apparent: It breaks TX capabilities
As soon as the device has been associated all following
TX frames will be queued in the hardware and never transmitted
to the air. Disabling sections of the link tuner did not
have the expected result, but completely disabling the
link tuner did have the right result (Both of my rt2570 devices
came back to life).
This should fix Fedora bug: 411481
v2: Fix typos
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb_vendor_request_large_buff is write-only, so it is
safe to make the argument a const.
Fixes compile warning:
drivers/net/wireless/rt2x00/rt73usb.c: In function 'rt73usb_load_firmware':
drivers/net/wireless/rt2x00/rt73usb.c:916: warning: passing argument 5 of 'rt2x00usb_vendor_request_large_buff' discards qualifiers from pointer target typ
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In kernel version 2.6.26-rc9 my wireless LAN card worked; but in the
released 2.6.26, my RaLink rt2500 card wouldn't associate.
Git-bisect led me to this patch:
61486e0f68
rt2x00: Remove ieee80211_tx_control argument from write_tx_desc()
I believe that there is a problem with that patch --- it
(inadvertantly) removes an extra line of code, that used to set the
DATABYTE_COUNT field.
This patch reinstates that line, and with it my card works again.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sequence counter can be accessed in IRQ context,
which means the lock protecting the counter should
be irqsave. To prevent making the entire intf->lock irqsave
without reason, create a new lock which only protects
the sequence counter.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the EEPROM_BBPTUNE_VGC word is valid, we should
override EEPROM_BBPTUNE_VGCLOWER field with the BBP
value.
And we should _not_ do that when EEPROM_BBPTUNE_R17 is valid.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the hardware has indicated the firmware upload has completed
and the device is ready, we should wait another millisecond to
make sure the device is really ready to continue.
Without this timout, bringing the interface down and up again will
fail due to incorrect register initialization.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if-statement to determine the new TX/RX antenna
configuration was incomplete. It lacks the general
else-clause when the antenna wasn't changed.
This is a correct event, since it can occur when only
one of the antenna's has been changed or when the new
configuration is being forced (like when the interface
has just been added).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Although most rt2x00 debugfs files don't contain
information which could compromise network security,
it is better to set the access permissions to root only.
This will be required when HW crypto is implemented,
because it could be possible to read the HW key from
the registers.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the queues are being initialized the entry flags fields must be
reset to 0. When this does not happen some entries might still be
marked as "occupied" after an ifdown & ifup cycle which would trigger
errors when the entry is being accessed:
phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 0.
Please file bug report to http://rt2x00.serialmonkey.com.
This also fixes the mac80211 warning:
------------[ cut here ]------------
WARNING: at net/mac80211/tx.c:1238 ieee80211_master_start_xmit+0x30a/0x350 [mac80211]()
which was triggered by the queue error.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 will only perform configuration changes from
mac80211 when the configuration option has changed.
This means it keeps track of the current active configuration
and will check these values when the config() callback function
is used.
However this causes breakage when the interface has been
brought down and up again, since all stored active values
aren't reset while the registers might have.
This is for example the case with rt61pci antenna registers which
will jump to invalid values when the interface has been started.
To make sure a full configuration takes place after the start()
callback function, a new flag is added which will be checked
during config() and skips the "what's changed" phase.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When sending the RTS/CTS frame fails, we should
free the skb buffer which was created.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_TX_CTL_ASSIGN_SEQ is not set,
the driver should disable hardware sequence counting
to make sure the mac80211 provided counter is used.
This fixes QOS sequence counting, since that is one
of the cases where mac80211 provides a seperate
sequence counter.
By moving the sequence counting code to rt2x00queue
we make sure that _all_ frames get the sequence counter,
including RTS/CTS and Beacon frames.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting up a beacon template, the length of the beacon is
calculated with the assumption that the SKB already contains
the Tx descriptor. In the case of beacons it doesn't.
This patch undoes the damage by adding the Tx descriptor length
to the beacon length. This is safe, because the shortest possible
beacon is longer than the Tx header.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Switches rt73usb to use large vendor requests for firmware
and beacons. This also fixes the garbled beacon bug.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds an extra rt2x00 vendor request function to support register
transfers beyond the CSR_CACHE_SIZE / USB packet size limit. This
is useful for firmware uploads, beacon templates and keys, all
of which are to large to do with a single USB request.
Signed-off-by: Iwo Mergler <Iwo@call-direct.com.au>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Olivier reported a difference between the EIFS
values used in the legacy driver and the one in
the rt2x00 drivers.
In rt2x00 the value was
( SIFS + (8 * (IEEE80211_HEADER + ACK_SIZE)) )
which comes down to 314us while the legacy driver uses the value 364us
This was caused because EIFS is: SIFS + DIFS + AckTime
This patch will fix this by adding the DIFS by the above value,
and creating a SHORT_EIFS define which uses the SHORT_DIFS.
Reported-by: Olivier Cornu <o.cornu@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I forgot this in the previous patch that made it unused.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I removed the special "default" meaning from the QoS
parameters, I forgot to update drivers and this lead to
warnings because some drivers were checking for the special
values and putting in defaults. This fixes that by removing
the default special-casing completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the legacy drivers the LED association status
must be reset after the firmware has been uploaded to the
hardware.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes mac80211 assign proper sequence numbers to
QoS-data frames. It also removes the old sequence number code
because we noticed that only the driver or hardware can assign
sequence numbers to non-QoS-data and especially management
frames in a race-free manner because beacons aren't passed
through mac80211's TX path.
This patch also adds temporary code to the rt2x00 drivers to
not break them completely, that code will have to be reworked
for proper sequence numbers on beacons.
It also moves sequence number assignment down in the TX path
so no sequence numbers are assigned to frames that are dropped.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new beacon handling from mac80211 we can
reorganize the beacon handling in rt2x00 as well.
This patch will move the function to the TX handlers,
and move all duplicate code into rt2x00queue.c.
After this change the descriptor helper functions
from rt2x00queue.c no longer need to be exported
outside of rt2x00lib and can be declared static.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inform drivers about the changed CTS protection settings.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes mac80211's beacon configuration handling
to never pass skbs to the driver directly but rather always
require the driver to use ieee80211_beacon_get(). Additionally,
it introduces "change flags" on the config_interface() call
to enable drivers to figure out what is changing. Finally, it
removes the beacon_update() driver callback in favour of
having IBSS beacon delivered by ieee80211_beacon_get() as well.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as an interface is enabled, and that interface is in adhoc or master mode,
the device will start raising beacondone interrupts. But before the first interrupt is
raised, mac80211 will probably not have send any beacons to the device yet, which
results in a NULL pointer error when the skb is being freed.
Note that the "raise beacondone interrupts without a beacon" is also a bug,
and will be addressed later. The more important bug however is preventing
the NULL pointer failt itself, since there might be other conditions that could trigger
it as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As soon as init_registers() was called, the rt2400/rt2500
would start raising beacondone interrupts. Since this is highly
premature since no beacons were provided yet, we should
initialize the synchronization register to 0.
This will make all drivers initialize it to 0 regardless
if they are raising beacondone interrupts or not, since it only
makes sense to have it completely disabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some register documentation in the register header files.
This allows better parsing by userspace scripts which in turn
helps debugging.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2400 is the only currently available rt2x00 driver which
supports reporting of the RX end time for frames.
Since mac80211 uses this information for IBSS syncing, it
is important that it is being reported.
v2: Complement 32 bits of RX timestamp with upper 32bits from TSF
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the rt2x00 singlethreaded workqueue and move
the link tuner and packet filter scheduled work to
the ieee80211_hw->workqueue again.
The only exception is the interface scheduled work
handler which uses the mac80211 interface iterator
under the RTNL lock. This work needs to be handled
on the kernel workqueue to prevent lockdep issues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We only need 4 bytes of headroom for alignment
purposes in the RX frame. It was previously higher
for optimization purposes which are no longer
possible due to DMA mappings.
v2: Fix patch error
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new rfkill interface there is no longer a need
for the input_polldev. Create a delayed_work structure
which we can put on the mac80211 workqueue and poll the
hardware every 1000ms.
v2: Decrease poll frequency from 100ms to 1000ms
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a circular locking dependency in the workqueue handling.
The interface work task uses the mac80211 function
ieee80211_iterate_active_interfaces() which grabs the RTNL lock.
However when the interface is brough down, this happens under the RTNL
lock as well, this causes problems because mac80211 will flush the workqueue
during the ifdown event. This causes mac80211 to wait until the driver has
completed all work which can't finish because it is waiting on the RTNL lock.
This is fixed by moving rt2x00 workqueue tasks on a different workqueue,
this workqueue can be flushed when the ieee80211_hw structure is removed
by the driver (when the driver is unloaded) which does not happen under the
RTNL lock.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/b43/rfkill.o
drivers/net/wireless/b43/rfkill.c: In function ‘b43_rfkill_soft_toggle’:
drivers/net/wireless/b43/rfkill.c:90: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
CC [M] drivers/net/wireless/b43legacy/rfkill.o
drivers/net/wireless/b43legacy/rfkill.c: In function ‘b43legacy_rfkill_soft_toggle’:
drivers/net/wireless/b43legacy/rfkill.c:92: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
CC [M] drivers/net/wireless/iwlwifi/iwl-rfkill.o
drivers/net/wireless/iwlwifi/iwl-rfkill.c: In function ‘iwl_rfkill_soft_rf_kill’:
drivers/net/wireless/iwlwifi/iwl-rfkill.c:56: warning: enumeration value ‘RFKILL_STATE_HARD_BLOCKED’ not handled in switch
Also handle RFKILL_STATE_{ON,OFF} -> RFKILL_STATE_{UNBLOCKED,SOFT_BLOCKED}
conversion since I'm already here...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During rt2x00usb_disable_radio() all pending urb's should
be killed and not only those from the RX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rt2x00queue_alloc_rxskbs() fails rt2x00queue_unitialize()
will be called which will free all rxskb. So we don't need
to do this in the rt2x00queue_alloc_rxskb() function as well.
rt2x00queue_free_skb() unmaps the DMA but doesn't clear the
allocation flag. Since the code is copied from rt2x00queue_unmap_skb()
anyway (and that function does clear the flag) we might as well
use that function directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without the preallocated DMA we can now safely increase
the queue size withotu negative impact on the memory
requirements of rt2x00.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sparse produces warnings about nested contain_of() statements,
this means that lines like:
interface_to_usbdev(to_usb_interface(rt2x00dev->dev));
will upset sparse.
Add a new macro to rt2x00usb.h which will convert to device
structure to the usb_device pointer in 2 steps to prevent this
sparse warning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With a bit of code moving to rt2x00lib within the
TX and RX paths we can now remove a lot of EXPORT_SYMBOL_GPL()
statements. This cleans up the interface between rt2x00lib
and the drivers and has the additional benefit that rt2x00pci
and rt2x00usb are trimmed down in size as well since they
have less to do.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current PCI drivers require a lot of pre-allocated DMA buffers. Reduce this
by using dynamically mapped skb's (using pci_map_single) instead of the pre-
allocated DMA buffers that are allocated at device start-up time.
At the same time move common RX path code into rt2x00lib from rt2x00pci and
rt2x00usb, as the RX paths now are now almost the same.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation of replacing the statically allocated DMA buffers with
dynamically mapped skbs, centralize the allocation of RX skbs to rt2x00queue.c
and let rt2x00pci already use them.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At the same time clean up the device administration a bit, by storing a pointer
to struct device instead of a void pointer that is dependent on the type of
device. The normal PCI and USB subsystem provided macros can be used to convert
the device pointer to the right type.
This makes the rt2x00 driver a bit more type-safe.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The skbs containing the beacons weren't properly cleaned up for rt2400pci, rt2500pci,
rt61pci, and rt73usb. Clean up those skbs in the manner appropriate for each driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the introduction of the ieee80211 fc handlers
we can now remove the rt2x00.h versions to use the
global versions.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Reviewed-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The usb_cache_mutex was not correctly released
under all circumstances. Both rt73usb as rt2500usb
didn't release the mutex under certain conditions
when the register access failed. Obviously such
failure would lead to deadlocks.
In addition under similar circumstances when the
bbp register couldn't be read the value must be
set to 0xff to indicate that the value is wrong.
This too didn't happen under all circumstances.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replaced by the new helper ieee80211_has_morefrags which is
more consistent with the intent of the function.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rework the alignment check in rt2x00dev.c to be independent of any
potential alignment measures that may be taken before. Just check
whether the payload is aligned based on the pointer addresses.
Note: This is preparatory for the dynamically mapped skb buffers
for the PCI drivers, as these need 4-byte alignment instead of the
currently enforced offset by 2 bytes.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAX_RX_SSI and MAX_NOISE are no longer used,
it is better to remove them entirely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For RTS/CTS-to-self frames the IEEE80211_TX_CTL_USE_RTS_CTS flag
should be cleared for the tx_info flags.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To really force the FIELD macros to determine
the first bit of the register field we should
use the __builtin_choose_expr() function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not safe to use the skb->cb area for both the rxd and
skb_frame_desc data at the same time, while they occupy an overlapping
piece of memory. This can lead to hard to trace crashes as pointers
within skb_frame_desc are pointing into nowhere, or the rxd data is
overwritten with non-sense.
Fix it by copying the rxd to a small buffer on the stack.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rt2x00pci will be switched over to dynamically mapped skb's
instead of statically allocated DMA buffers, it no longer can handle
alignment of RX packets in a copy step, and needs to implement the
same scheme as rt2x00usb does.
In order to make the patch on dynamically mapped skb's smaller,
already centralize the alignment handling into rt2x00lib. This allows
us to move more code in rt2x00lib, and thus remove code duplication
between rt2x00usb and rt2x00pci.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The data and data_len fields aren't really necessary in struct
skb_frame_desc, as they can be deduced from the skb itself.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX queues shouldn't be kicked after each frame that is put into the
queue. This could cause problems during RTS and CTS-to-self as well
as with fragmentation. In all those cases you want all frames to be
send out in a single burst. Off course we shouldn't let the queue fill
up entirely, thus we introduce a 10% threshold which, when reached,
will force the frames to be send out regardless of the frame.
In addition we should prevent queues to become full in such a way
that the tx() handler can fail. Instead of stopping the queue when
it is full, we should stop it when it is below the threshold.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The write_tx_data functions in rt2x00pci and rt2x00usb have
a lot in common. This moves that duplicate code into
rt2x00queue_write_tx_frame().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb_kick_tx_queue() will loop over all entries
within the INDEX_DONE->INDEX range and kick each entry
which is pending to be kicked. This makes the kick_tx_queue
approach work the same as with the PCI drivers which
will allow for more code generalisation into rt2x00lib.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
qid should be initialized to QID_BEACON and QID_ATIM
for the beacon and atim quue. This makes checking for
a particular queue much saner, and it shouldn't harm,
because the only places where the value is send to
the hardware, we are allowed to send any value we
want since it is only used as argument in the
TX done register.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2x00_set_field functions are very often used,
but GCC is better able to optimize them when they
are macros instead of static inline functions.
After changing it to macro's each rt2x00 driver will
loose about ~3500 bytes in size.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00usb doesn't need the TX descriptor in the TX done path.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 doesn't send RTS or CTS-to-self frames through
the tx() callback functions so we don't need to check it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce code duplication by moving led structure initialization
into a per-driver function.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reduce goto usage
* Mark if-statements which are true on hardware error unlikely()
* Cleanup debug messages
This makes the code look nicer and be better optimized since
the chance of hardware errors should be very small.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By using __ffs() the register offsets were always calculated
at run-time which all FIELD32/FIELD16 definitions were builtin
constants. This means we can heavily optimize the register handling
by allowing GCC to do all the work during compilation.
Add some compile_ffs() macros to perform the calculation at
compile time. After this each rt2x00 module size is reduced
by ~2500 bytes. And the stack size of several functions is reduced
as well which further limits the number of rt2x00 results in
'make checkstack'.
v2: Merge GertJan's bugfix of patch [1/11] directly into this patch
   instead of providing it as seperate patch.
v3: Add extra parentheses when bitshifting __x
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select LEDS_CLASS need to depend on NEW_LEDS so that
undefined symbols are not used in the build.
The alternative is to select NEW_LEDS, which some drivers do.
This patch fixes the led_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Config symbols that select RFKILL need to depend on INPUT so that
undefined symbols are not used in the build.
This patch fixes the input_* symbols build errors.
(.text+0x174cdc): undefined reference to `input_unregister_device'
(.text+0x174d9f): undefined reference to `input_allocate_device'
(.text+0x174e2d): undefined reference to `input_register_device'
(.text+0x174e53): undefined reference to `input_free_device'
rt2x00rfkill.c:(.text+0x176dc4): undefined reference to `input_allocate_polled_device'
rt2x00rfkill.c:(.text+0x176e8b): undefined reference to `input_event'
rt2x00rfkill.c:(.text+0x176e9f): undefined reference to `input_event'
(.text+0x176eca): undefined reference to `input_unregister_polled_device'
(.text+0x176efc): undefined reference to `input_free_polled_device'
(.text+0x176f37): undefined reference to `input_free_polled_device'
(.text+0x176fd8): undefined reference to `input_register_polled_device'
(.text+0x1772c0): undefined reference to `led_classdev_resume'
(.text+0x1772d4): undefined reference to `led_classdev_resume'
(.text+0x1772e8): undefined reference to `led_classdev_resume'
(.text+0x17730a): undefined reference to `led_classdev_suspend'
(.text+0x17731e): undefined reference to `led_classdev_suspend'
(.text+0x17732f): undefined reference to `led_classdev_suspend'
rt2x00leds.c:(.text+0x177348): undefined reference to `led_classdev_unregister'
rt2x00leds.c:(.text+0x1773c0): undefined reference to `led_classdev_register'
rfkill-input.c:(.text+0x209e4c): undefined reference to `input_close_device'
rfkill-input.c:(.text+0x209e53): undefined reference to `input_unregister_handle'
rfkill-input.c:(.text+0x209ea1): undefined reference to `input_register_handle'
rfkill-input.c:(.text+0x209eae): undefined reference to `input_open_device'
rfkill-input.c:(.text+0x209ebb): undefined reference to `input_unregister_handle'
rfkill-input.c:(.init.text+0x17405): undefined reference to `input_register_handler'
rfkill-input.c:(.exit.text+0x194f): undefined reference to `input_unregister_handler'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
None of the rt2x00 PCI devices support 64-bit DMA addresses (they all
only accept 32-bit buffer addresses). Hence it makes no sense to try to
enable 64-bit DMA addresses. Only try to enable 32-bit DMA addresses.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a "BUG: unable to handle kernel paging request"
bug in rt73usb which was caused by killing the guardian_urb
while it had never been allocated for rt73usb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib_beacondone() is called from interrupt context,
this means we cannot use the mac80211 interface iterator
that uses the rtnl lock (since that uses a mutex which can sleep).
Instead we should use the atomic mac80211 interface iterator.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the antenna configuration has changed we should reset
the antenna RSSI value. Otherwise the value will be influenced
by the previous configuration quality which in turn will affect
the antenna diversity.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link quality estimation became quite low for all rt2x00 drivers
because the number of retries it took to send the frame were
counted as failure.
This does not correspond to the legacy driver link quality calculation,
by not counting it we will send somewhat more optimistic values to
mac80211.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the tx() handler runs while the device has disapeared,
we did return NETDEV_TX_OK but didn't free the skb.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates mac80211 and drivers to be multi-queue aware and
use that instead of the internal queue mapping. Also does a number
of cleanups in various pieces of the code that fall out and reduces
internal mac80211 state size.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts mac80211 and all drivers to have transmit
information and status in skb->cb rather than allocating extra
memory for it and copying all the data around. To make it fit,
a union is used where only data that is necessary for all steps
is kept outside of the union.
A number of fixes were done by Ivo, as well as the rt2x00 part
of this patch.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies struct ieee80211_tx_control to give band
info and the rate index (instead of rate pointers) to drivers.
This mostly serves to reduce the TX control structure size to
make it fit into skb->cb so that the fragmentation code can
put it there and we can think about passing it to drivers that
way in the future.
The rt2x00 driver update was done by Ivo, thanks.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Having drivers start queues is just confusing, their ->start()
callback can block and do whatever is necessary, so let mac80211
start queues and have drivers wake queues when necessary (to get
packets flowing again right away.)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the pending removal of the tx_control structure
we can merge the RX and TX entry private data structure
in advance. This will temporarily increase the required
memory for the queue, but that overhead will only be limited.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the rxdesc structure is properly memsetted before passed to
the driver. This means we don't have to reinitialize the flags
and dev_flags fields in the drivers again.
This will prevent problems when the rxdone handler is adding
flags in a earlier status and will make the code look nicer
when we are adding more read attributes in the rxdone handler
in the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split rt2x00lib_write_tx_desc() up into a TX descriptor initializor
and TX descriptor writer.
This split is required to properly allow mac80211 to move its
tx_control structure into the skb->cb array.
The rt2x00queue_create_tx_descriptor() function will read all tx control
information and convert it into a rt2x00 TX descriptor information structure.
After that function is complete, we have all information we needed from the
tx control structure and are free to start writing into the skb->cb array
for our own purposes.
rt2x00queue_write_tx_descriptor() will be in charge of really sending
the TX descriptor to the hardware and kicking the TX queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation of replacing the statically allocated data DMA buffers with DMA-mapped
skb's we need to change the TXD handling of the PCI drivers, by moving the programming
of the buffer address fields to the actual TXD writing at TX time, instead of at start-up
time.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to usage of memmove() in rt2x00usb the descriptor can become
corrupted because it is being overwritten by the data part.
Overall having the descriptor in front of the frame is a bad idea,
we can however use the skb->cb array for this task, since that
contains more then enough room to hold the entire descriptor and
preserve the information long enough.
After this we can also cleanup the alignment code a bit to make it
work a bit more flexible to allow for all kinds of odd header lengths.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the integration of the mac80211 multiqueue patches it has become possible that the
mac80211 layer modifies the number of TX queues that is stored inside the ieee80211_hw
structure, especially when multi-queue is not selected.
The rt2x00 drivers are not well suited to handle that situation, as they allocate the
queue structures before mac80211 has modified the number of queues it is going to use,
and also expect the number of allocated queues to match the hardware implementation.
Hence, ensure that rt2x00 maintains by itself the number of queues that the hardware
supports, and, at the same time, making is not dependent on the preservation of contents
inside a mac80211 structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the last remaining information details read from ieee80211_tx_control
in the drivers to the txentry_desc structure. After this we can
remove ieee80211_tx_control from the argument list for the callback function,
which makes it easier when the control information is moved into skb->cb
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx_status enumeration was broken since the introduction
of rt61pci. That driver uses different values to report the
status of the tx action.
This would lead to frames that were reported as success but
actually failed to be send out, or frames that were neither
successfull or failure which were reported as failure.
Fix this by change the TX status reporting and more explicitely
check for failure or success. Note that a third possibility is
added "unknown". Not all hardware (USB) can report the actual
TX status, for rt61pci some frames will receive this status
because the TXdone handler is never called for those frames.
This unknown will now be handled as neither success or failure,
so we no longer increment the failure counter while this conclusion
could not be determined from the real status of the frame.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove frame_type from skb_frame_desc and pass it
as argument to rt2x00debug_dump_frame().
Change data_len and desc_len to unsigned short
to save another 4 bytes in skb_frame_desc. Note that
this was the only location where the data_len and
desc_len was not yet treated as unsigned short.
This trim is required to help mac80211 with adding
the TX control and TX status informtation into the
skb->cb structure. When that happens, drivers will
have approximately 40 bytes left to use freely.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
trying to clean up the signal/noise code. the previous code in mac80211 had
confusing names for the related variables, did not have much definition of
what units of signal and noise were provided and used implicit mechanisms from
the wireless extensions.
this patch introduces hardware capability flags to let the hardware specify
clearly if it can provide signal and noise level values and which units it can
provide. this also anticipates possible new units like RCPI in the future.
for signal:
IEEE80211_HW_SIGNAL_UNSPEC - unspecified, unknown, hw specific
IEEE80211_HW_SIGNAL_DB - dB difference to unspecified reference point
IEEE80211_HW_SIGNAL_DBM - dBm, difference to 1mW
for noise we currently only have dBm:
IEEE80211_HW_NOISE_DBM - dBm, difference to 1mW
if IEEE80211_HW_SIGNAL_UNSPEC or IEEE80211_HW_SIGNAL_DB is used the driver has
to provide the maximum value (max_signal) it reports in order for applications
to make sense of the signal values.
i tried my best to find out for each driver what it can provide and update it
but i'm not sure (?) for some of them and used the more conservative guess in
doubt. this can be fixed easily after this patch has been merged by changing
the hardware flags of the driver.
DRIVER SIGNAL MAX NOISE QUAL
-----------------------------------------------------------------
adm8211 unspec(?) 100 n/a missing
at76_usb unspec(?) (?) unused missing
ath5k dBm dBm percent rssi
b43legacy dBm dBm percent jssi(?)
b43 dBm dBm percent jssi(?)
iwl-3945 dBm dBm percent snr+more
iwl-4965 dBm dBm percent snr+more
p54 unspec 127 n/a missing
rt2x00 dBm n/a percent rssi+tx/rx frame success
rt2400 dBm n/a
rt2500pci dBm n/a
rt2500usb dBm n/a
rt61pci dBm n/a
rt73usb dBm n/a
rtl8180 unspec(?) 65 n/a (?)
rtl8187 unspec(?) 65 (?) noise(?)
zd1211 dB(?) 100 n/a percent
drivers/net/wireless/ath5k/base.c: Changes-licensed-under: 3-Clause-BSD
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When, for some reason, the rt2x00pci module fails to allocate DMA memory for
the queues, it tries to undo the complete initialization of the PCI device,
including freeing of the irq. This results in the following error in dmesg, as
the irq hadn't been requested yet:
[ 78.123456] Trying to free already-free IRQ 17
Fix this by implementing proper error handling code, instead of just using the
full uninitialization function.
Signed-off-by: Gertjan van Wingerde <gwingerde@kpnplanet.nl>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During initialization the initialize() callback function
in rt2x00pci and rt2x00usb will cleanup the mess they made.
rt2x00lib shouldn't call uninitialize because the callback function already
cleaned up _and_ the DEVICE_INITIALIZED isn't set which causes the
rt2x00lib_uninitialize() to halt directly anyway. All that is required
to be cleaned up by rt2x00lib is the queue, and that can be done by
calling rt2x00queue_uninitialize() directly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00pci allocates DMA for descriptor and data,
rt61pci doesn't use this for the beacon, but it can
use the descriptor part as temporary buffer instead
of using pskb_expand_head().
Using this temporary buffer is obviously much better
then reallocating the skb buffer...
At the same time we can set the data length for the
beacon queue at 0, to make sure no DMA is allocated for
data (but just for the descriptor).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Filipus Klutiero <chealer@gmail.com>,
the rt2x00 Kconfig entries should be updated with
specific chipset notifications.
This cleans up Kconfig by explicitly mentioning the
supported chipsets for each drivers, and uses the
same chipset family names as mentioned on the Ralink website.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This
* makes the queue number passed to drivers a u16
(as it will be with skb_get_queue_mapping)
* removes the useless queue number defines
* splits hw->queues into hw->queues/ampdu_queues
* removes the debugfs files for per-queue counters
* removes some dead QoS code
* removes the beacon queue configuration for IBSS
so that the drivers now never get a queue number
bigger than (hw->queues + hw->ampdu_queues - 1)
for tx and only in the range 0..hw->queues-1 for
conf_tx.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue info in struct ieee80211_tx_status is never used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The callback takes a ieee80211_tx_queue_stats with a contained
array of ieee80211_tx_queue_stats_data, remove the former, rename
the latter to ieee80211_tx_queue_stats and make tx_stats() take
the array directly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing kernel-doc variables for structures/functions.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add some helper macro's to help determining the
the timeout for USB register access.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the rt2x00 queue enumeration as much as possible,
removing the usage of the mac80211 queue numbering
wherever it is possible.
This makes it easier for mac80211 to change it queue
identification scheme without having to deal with
big changes in the rt2x00 code.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A lot more is needed to support mixed interfaces then just this flag,
such things need new redesigns in rt2x00lib to actually make it happen.
So far there doesn't exist a Ralink chipset that can handle it, so
we might as well remove the flag for now and see what should be done
whenever a device appears that can handle it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver has set the set_rts_threshold() callback function
to mac80211 it is capable of generating RTS and CTS-to-self frames
inside the hardware and rt2x00lib doesn't have to create them
in software.
Only rt2800pci and rt2800usb support this feature.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was an obvious typo in LED structure
initialization which caused the radio and quality/activity
leds to be incorrectly initialized which resulted in
the leds not being enabled.
Additionally add the rt2x00led_led_activity() handler
that will enable TX/RX activity leds when the radio
is being enabled.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The timing settings for 1MBs should exclude
the short preamble bit since that only applies
to 2MBs, 5.5MBs and 11MBs.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2x00lib_intf_scheduled_iter() we use the hw->beacon_update()
callback function. This means that it should behave similarly as mac80211
when that uses the function.
This means that the skb should only be freed when beacon_update() has failed,
otherwise the driver is the owner and is responsible for freeing the buffer.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The layer above will free the skb in an error case.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now rt2x00lib handles the initial configure_filter() command, we can
directly call lib->config_filter() in scheduled context since the
called function will no longer check if anything has changed (which is
now handled in rt2x00lib as well).
This fixes a endless loop with USB drivers where the config_filter
command was scheduled time and time again without sending any command
to the device.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement triggers inside rt2x00 itself based
on input from mac80211. This replaces the method
of using the mac80211 trigger events which do
not work for USB drivers due to the scheduling
requirement.
After this patch RT2500USB_LEDS and RT73USB_LEDS
no longer need to be tagged as broken since they
now support LED handling again without having to
check for in_atomic().
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TO_DS filter does not only depend on the FIF_PROMISC_IN_BSS flag
provided by mac80211, but also on the intf_ap_count count.
This makes sense, since when Master mode is active, we should all frames
that are send to the active AP (the device itself).
This means that when an interface is added we should force the
packet filter to be updated during the next mac80211 call of
configure_filter() to make sure the intf_ap_count field is checked.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Invert the check for scheduling the packet_filter configuration.
When DRIVER_REQUIRE_SCHEDULED is not set we should immediately
configure the the filter.
This fixes the 'infinite calls to rt2x00mc_configure_filter'
bug reported by Bas Hulsken.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These small changes restore the rt2x00 sources to the way Ivo intended.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some hardware never seem to accept the "goto sleep" command, since the legacy
drivers don't have suspend and resume handlers the entire code for it was
basically a educated guess (based on the "enable radio" code).
This patch will only print a warning when the "goto sleep" command fails, and
just continues as usual. Perhaps that means the device will not reach a sleep
state and consumes more power then it should, but it is equally possible it
simply needs some seconds longer to sleep. Anyway, by making the command
non-fatal it will not block the rest of the suspend procedure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt73usb and rt2500usb used in_atomic to determine
if a configuration step should be rescheduled or not.
Since in_atomic() is not a valid method to determine
if sleeping is allowed we should fix the way this is handled
by adding a new flag to rt2x00.
In addition mark LED class support for the drivers broken
since that also uses the broken in_atomic() method but
so far no solution exists to have LED triggers work only
in scheduled context.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been observed on rt2500pci hardware that some
frames received with signal 0x0C do not have the OFDM
flag set.
Signals can have 2 meanings:
1) The PLCP value
2) The bitrate * 10
For rt2500pci (1) is for frames received with a OFDM rate,
and (2) is for frames received with a CCK rate.
But 0x0C is a invalid bitrate value but is a valid PLCP
value for 54Mbs (obvious OFDM rate).
This means that it is possible that the hardware does not
set the OFDM bit correctly under all circumstances.
This results in rt2x00 failing to detect the rate and
mac80211 triggering a WARN_ON() and dropping the frame.
To bypass this, print a warning when such a frame is received,
and reset the rate to the lowest supported rate for the current band.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rxdone_entry_desc structure contains 3 fields
which are always 1 or 0. We can safe 8 bytes by
replacing them with a single dev_flags fields which
contain the flags for those settings.
Additionally we can remove the OFDM flag since it
is no longer used since the introduction of the
SIGNAL_PLCP flag.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the id for Corega CG-WLUSB2GPX.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only rt2400pci can have the preamble bit set in the PLCP value,
for all other drivers it should not be cleared since that will
conflict with the plcp values for OFDM rates.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After sampling hundreds of RX frame descriptors,
the results were conclusive:
- The Ralink documentation regarding the SIGNAL and RSSI are wrong.
It turns out that of the 5 BBR registers, we should not use BBR0 and BBR1
for SIGNAL and RSSI respectively, but actually BBR1 and BBR2.
BBR0 does show values, but the exact meaning remains unclear,
but they cannot be translated into a SIGNAL or RSSI field.
BBR3, BBR4 and BBR5 are always 0, so their meaning is unknown.
As it turns out, the reported SIGNAL is the PLCP value, this
in contradiction to what was expected looking at rt2500pci which
only reported the PLCP values for OFDM rates and bitrate values
for CCK rates.
This means we should let the driver raise the flag about the contents
of the SIGNAL field so rt2x00lib can always do the right thing based
on what the driver reports.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to a terrible typo the RX DMA base address
was initialized to the beacon base address.
Obviously bad things happen with bugs like that....
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The basic rate which is configured in the register
should not match all supported rates, but only the _basic_ rates.
Fix this by adding a new flag to the rt2x00_rate structure
and whenever the mode is changed, loop over all available rates
for that band to get the basic rate mask.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whatever mode we are in, according to the legacy drivers
we should always enable TSF ticking/counting.
We should also always enable the TBCN/TBTT field,
this field is only disabled during beacon regeneration.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00dev isn't interested in the rt2x00leds_register() value
anyway. So lets make it return void to even prevent people from
assuming there is anybody interested in the returnvalue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename config_preamble() to config_erp() and cleanup argument
list by putting it all into a single structure.
This will make the function more meaningful and easier to
expand later. This second option is mostly intended to make
the patch "mac80211: proper short-slot handling" from Johannes Berg
easier to apply for rt2x00.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mac sets the IEEE80211_TXCTL_SEND_AFTER_DTIM flag, we should
check if the ATIM queue is available in the driver and put the
frame in that queue for proper behavior (send frame after beacon interval).
Unfortunately not all drivers have this ATIM queue, and will lack
this feature for now.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib should filter SW diversity out before sending any configuration
changes to the driver. When rt2x00lib fails to do this, it is important
that such events are reported because it _must_ be fixed.
So upgrading the error level to a BUG_ON() which will make sure
this bug gets noticed whenever it happens.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00lib depended on 2 crc algorithms because rt61/rt73
use a different algorithm then rt2800. This means that
even when only 1 algorithm was needed, the dependency was
still present for both.
By moving the checksum generation to the driver we can clean
up 2 annoying flags (which indicated which checksum was required)
and move the dependency to where it belongs: the driver.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The queue->lock could be grabbed from interrupt context,
which could lead to lockdep panic like this:
kernel: ======================================================
kernel: [ INFO: soft-safe -> soft-unsafe lock order detected ]
kernel: 2.6.25-0.95.rc4.fc9 #1
kernel: ------------------------------------------------------
kernel: rt2500pci/1251 [HC0[0]:SC0[1]:HE1:SE0] is trying to acquire:
kernel: (&queue->lock){--..}, at: [<ffffffff88213339>] rt2x00queue_get_entry+0x5a/0x81 [rt2x00lib]
kernel:
kernel: and this task is already holding:
kernel: (_xmit_IEEE80211){-...}, at: [<ffffffff8122e9a3>] __qdisc_run+0x84/0x1a9
kernel: which would create a new lock dependency:
kernel: (_xmit_IEEE80211){-...} -> (&queue->lock){--..}
kernel:
kernel: but this new dependency connects a soft-irq-safe lock:
kernel: (_xmit_ETHER){-+..}
kernel: ... which became soft-irq-safe at:
kernel: [<ffffffffffffffff>] 0xffffffffffffffff
kernel:
kernel: to a soft-irq-unsafe lock:
kernel: (&queue->lock){--..}
kernel: ... which became soft-irq-unsafe at:
kernel: ... [<ffffffff810545a2>] __lock_acquire+0x62d/0xd63
kernel: [<ffffffff81054d36>] lock_acquire+0x5e/0x78
kernel: [<ffffffff812a1497>] _spin_lock+0x26/0x53
kernel: [<ffffffff88212f98>] rt2x00queue_reset+0x16/0x40 [rt2x00lib]
kernel: [<ffffffff88212fd4>] rt2x00queue_alloc_entries+0x12/0xab [rt2x00lib]
kernel: [<ffffffff88213091>] rt2x00queue_initialize+0x24/0xf2 [rt2x00lib]
kernel: [<ffffffff88212036>] rt2x00lib_start+0x3b/0xd4 [rt2x00lib]
kernel: [<ffffffff88212609>] rt2x00mac_start+0x18/0x1a [rt2x00lib]
kernel: [<ffffffff881b9a4b>] ieee80211_open+0x1f3/0x46d [mac80211]
kernel: [<ffffffff8121d980>] dev_open+0x4d/0x8b
kernel: [<ffffffff8121d41e>] dev_change_flags+0xaf/0x172
kernel: [<ffffffff81224fc2>] do_setlink+0x276/0x338
kernel: [<ffffffff81225198>] rtnl_setlink+0x114/0x116
kernel: [<ffffffff812262fc>] rtnetlink_rcv_msg+0x1d8/0x1f9
kernel: [<ffffffff8123649a>] netlink_rcv_skb+0x3e/0xac
kernel: [<ffffffff8122611a>] rtnetlink_rcv+0x29/0x33
kernel: [<ffffffff81235eed>] netlink_unicast+0x1fe/0x26b
kernel: [<ffffffff81236224>] netlink_sendmsg+0x2ca/0x2dd
kernel: [<ffffffff812103b3>] sock_sendmsg+0xfd/0x120
kernel: [<ffffffff812105a8>] sys_sendmsg+0x1d2/0x23c
kernel: [<ffffffff8100c1c7>] tracesys+0xdc/0xe1
kernel: [<ffffffffffffffff>] 0xffffffffffffffff
This can be fixed by using the irqsave/irqrestore versions
during the queue->lock handling.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix trivial log message.
Signed-off-by: Luis Correia <luis.f.correia@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When fixing up the packet alignment, if we had to add 2 bytes to the front of
the skb we need to remember to take them off the end afterwards. This fixes
reception of encrypted packets which were otherwise failing with an invalid
ICV.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not write 0 to the beacon sync register during
config_intf() since that will clear out the beacon interval
and forces the beacon to be send out at the lowest interval.
(reported by Mattias Nissler).
The side effect of the same bug was that while working with
multiple virtual AP interfaces a change for any of those
interfaces would disable beaconing untill an beacon update
was provided.
This is resolved by only updating the TSF_SYNC value during
config_intf(). In update_beacon() we disable beaconing
temporarily to prevent fake beacons to be transmitted.
Finally kick_tx_queue() will enable beaconing again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In rt2x00lib_write_tx_desc() the skb->data and skb->len fields
were incorrectly used. For USB drivers both of those values
contain invalid data (skb->data points to the device descriptor,
skb->len contains the frame _and_ descriptor length).
Instead of using the skbuffer fields we should use the skbdesc
fields which are correctly initialized and contain all the data
that we need.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rxdesc->size is unitialized before the desriptor has been read.
Move the truncation of the sk buffer to the moment all variables
have been initialized.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
skbdesc->desc_len is uninitialized at the start
of the function. So it is a _bad_ idea to use it...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sizeof() operator was incorrectly applied to the pointer, not the struct.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the TX path, the driver didn't copy the TX control data structure. Thus, it
was invalid in the TX done handler, causing serious trouble and misbehaviour.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some architectures give problems when reading
RX frame descriptor words when the descriptor
is not aligned on a 4 byte boundrary.
Due to optimalizations for the ieee80211 payload
4 byte alignment, it is no longer guarenteed
that the descriptor is placed on the 4 byte
boundrary (In fact, for rt73usb it is absolutely
never aligned to 4 bytes, for rt2500usb it depends
on the length of the payload).
This will copy the descriptor to a 4 byte aligned
location before it is read for the first time.
This will also move the payload data alignment
in rt2x00usb (instead of inside the driver) where
it has always belonged.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add suspend/resume handlers to rt2x00rfkill to have it stop
the input-polldev and prevent it from calling rt2x00 during
suspend period. This could lead to a NULL pointer fault when
rt2x00 suspended, but polldev send a request, because
the csr_addr is NULL.
Also don't let the rfkill allocation/registration block
the initialization of the entire device. Just print a warning
and continue as if nothing happened.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On rt73 and rt61 disabling reception of multicast packets also disables
broadcast traffic which we never want to do. Therefore we should never
disable multicast.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a typo in the link tuner where accidently the
2GHz band was checked instead of the 5GHz band.
This forced the link tuner to work in an invalid
range for the currently active band.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ivo van Doorn