- check SDAC bit of AC97 primary codec when create "rear" device 3,
"4ch" device 2 and "4ch Duplication" switch as the card need a four channels
AC97 codec to support surround40.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lots of sound drivers were getting module.h via the implicit presence
of it in <linux/device.h> but we are going to clean that up. So
fix up those users now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The implicit presence of module.h lured several users into
incorrectly thinking that they only needed/used modparam.h
but once we clean up the module.h presence, these will show
up as build failures, so fix 'em now.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Add the PCM rules to allow disabling the PCM playback and capture SRCs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The installation of the minimum period size constraint in the PCM open
callbacks was not checked for errors. Add this check, and move the call
to the beginning of the function to avoid having to do any cleanups in
the error case.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The semantics of snd_mpu401_uart_new()'s interrupt parameters are
somewhat counterintuitive: To prevent the function from allocating its
own interrupt, either the irq number must be invalid, or the irq_flags
parameter must be zero. At the same time, the irq parameter being
invalid specifies that the mpu401 code has to work without an interrupt
allocated by the caller. This implies that, if there is an interrupt
and it is allocated by the caller, the irq parameter must be set to
a valid-looking number which then isn't actually used.
With the removal of IRQF_DISABLED, zero becomes a valid irq_flags value,
which forces us to handle the parameters differently.
This patch introduces a new flag MPU401_INFO_IRQ_HOOK for when the
device interrupt is handled by the caller, and makes the allocation of
the interrupt to depend only on the irq parameter. As suggested by
Takashi, the irq_flags parameter was dropped because, when used, it had
the constant value IRQF_DISABLED.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
YDSXGR_LEGACYOUTVOL is a Playback Volume control for OPL3 FM Synth.
Signed-off-by: Raymond Yau <superquad.vortex2@gmail.com>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The name argument of request_irq() appears in /proc/interrupts, and
it's quite ugly when the name entry contains a space or special letters.
In general, it's simpler and more readable when the module name appears
there, so let's replace all entries with KBUILD_MODNAME.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The convention for pci_driver.name entry in kernel drivers seem to be
the module name or equivalent ones. But, so far, almost all PCI sound
drivers use more verbose name like "ABC Xyz (12)", and these are fairly
confusing when appearing as a file name.
This patch converts the all pci_driver.name entries in sound/pci/* to
use KBUILD_MODNAME for more unified appearance.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Simplify the info callback by using the snd_ctl_enum_info() helper function.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the interval timer to be programmed with its full 96 kHz
precision.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kill snd_assert() in sound/pci/*, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Standardise both in-kernel and loaded firmware to be stored as
little-endian instead of host-endian.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
YDSXGR_BUF441OUTVOL register isn't initialized properly. This may lead to
a silent output at full volume of unchanged "Wave Playback Volume".
http://bugzilla.kernel.org/show_bug.cgi?id=10963
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly in the rest of
PCI drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix schedule_timeout() use in alsa-kernel. Mostly just
schedule_timeout(1) --> schedule_timeout_uninterruptible(1)
The wavefront_synth one fixes the surrounding loop as well. In ymfpci_main,
delete a superfluous set_current_state() and in soc/soc-dapm.c replace an
_interruptible with _uninterruptible in some debug code; it's not waiting
for signals.
Signed-off-by: Rene Herman <rene.herman>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The existing code for handling the 44.1 slot's volume has two problems:
the volume is not affected by the 'Wave Playback Volume' mixer control,
and the BUF441OUTVOL register, which is used to control the per-
substream volume for this slot, uses a different scale than the gain
fields of the other slots.
This patch makes the BUF441OUTVOL register a shadow of the
NATIVEDACOUTVOL register so that the Wave volume is consistent for all
substreams.
As a consequence of this, the per-substream PCM volume control gets no
longer activated for the substream using this slot. The code for
(de)activating the mixer control is moved from the open/close to the
prepare/trigger_stop callbacks so that it is able to determine the
substream's slot.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't use request_firmware() if the internal firmwares are defined
via Kconfig. Otherwise it results in a significant delay at loading
time (minutes).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Some drivers are already ifdefs for enabling external firmwares
but not defined in Kconfig. Now they appear as the kernel configs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Mark TLV data as 'const'
Signed-of-by: Philipp Matthias Hahn <pmhahn@pmhahn.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Following patch will make the driver to use the 44.1kHz SRC automatically
if the pcm source is 44.1kHz signed 16bit stereo.
The SRC is available in YMF754 only.
Signed-off-by: Teru KAMOGASHIRA <teru@sodan.ecc.u-tokyo.ac.jp>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Load the DSP and controller microcode using request_firmware(), if
possible, instead of using the built-in firmware.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix IRQ flags for PCI devices.
The shared IRQs for PCI devices shouldn't be allocated with
IRQF_DISABLED. Also, when MSI is enabled, IRQF_SHARED shouldn't
be used.
The patch removes unnecessary cast in request_irq and free_irq,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the type of PCI revision to char from int and avoid invalid
assignment with pointer cast.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This patch fixes incorrect assignment of swap_rear,
which was broken since patch 'ymfpci - make rear channel swap optional'
It removes module_param rear_swap.
Signed-off-by: Glen Masgai <mimosius@gmx.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
- Check the return value of pci_enable_device() and request_irq()
in the suspend. If any error occurs there, disable the device
using snd_card_disconnect().
- Call pci_set_power_state() properly with pci_choose_state().
- Fix the order to call pci_set_power_state().
- Removed obsolete house-made PM codes in some drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Added the linear volume TLV entries for YMFPCI native volume controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Change the 5th argument of snd_mpu401_uart_new() to bit flags
instead of a boolean. The argument takes bits that consist of
MPU401_INFO_XXX flags.
The callers that used the value 1 there are replaced with
MPU401_INFO_INTEGRATED.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
Added rear_swap module option / kernel parameter to configure the rear
channel swapping. Default value is enable to make the AC3 passthrough
working, but analog only users might revert the previous behaviour.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: YMFPCI driver
The routing of the effect 2/3 channels to the digital output is the
opposite of the rear analog output (left/right swapped).
We make the order correct for the digital output (which will make the
analog rear have the channels swapped) to make AC3 output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
