Commit graph

856 commits

Author SHA1 Message Date
Bob Liu
4d676fc5c3 spi/bfin_spi: support for multiples of 8bits with hardware CS
We can do multiples of 8bit transfers when using the hardware CS and a
little bit of magic, so make it work.

Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-15 13:56:58 -07:00
Sebastian Andrzej Siewior
0f3e1d27a7 spi/pxa2xx pci: fix the release - remove race
Right now the platform device and its platform data is included in one big
struct which requires its custom ->release function. The problem with the
release function within the driver is that it might be called after the
driver was removed because someone was holding a reference to it and it
was not called right after platform_device_unregister(). So we also free
the platform device memory to which one might hold a reference.

This patch uses the normal pdev functions so this kind of race does not
occur.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-15 13:25:36 -07:00
Bernhard Walle
7d48ec3698 spi/spidev: Add 32 bit compat ioctl()
Add the compat_ioctl for operations on /dev/spi* so that 32 bit
userspace applications can access SPI. As far as I can see all data
structure are already prepared for that, so no additional conversion has
to be done.

My use case is MIPS with N32 userspace ABI and toolchain, and that was
also the platform where I tested it successfully (Cavium Octeon).

Signed-off-by: Bernhard Walle <walle@corscience.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-02-03 09:55:43 -07:00
Tony Lindgren
59b479e098 omap: Start using CONFIG_SOC_OMAP
We want to have just CONFIG_ARCH_OMAP2, 3 and 4. The rest
are nowadays just subcategories of these.

Search and replace the following:

ARCH_OMAP2420		SOC_OMAP2420
ARCH_OMAP2430		SOC_OMAP2430
ARCH_OMAP3430		SOC_OMAP3430

No functional changes.

Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Sourav Poddar <sourav.poddar@ti.com>
2011-01-27 16:39:40 -08:00
Guennadi Liakhovetski
9dabb3f326 spi/spi_sh_msiof: consolidate data in 8-bit mode into 32-bit words
Instead of sending data 8 bits at a time in 8-bit SPI mode, swap bytes
and send and receive them 32 bits at a time. Tested with an SD-card,
with which this patch reduced the number of interrupts by 50%, when
reading 5MiB of data (there are also small service packets, the number
of interrupts, produced by 512-byte sectors should, of course, drop by
75%), and improved throughput by more than 40%.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-21 10:02:35 -07:00
Guennadi Liakhovetski
e2dbf5ebcc spi/spi_sh_msiof: cosmetic clean-up
1. sort headers alphabetically
2. use fixed-size types u8, u16, u32 for register values and transferred data
3. simplify some arithmetic operations

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[grant.likely@secretlab.ca: removed label indentation change]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-21 09:49:39 -07:00
Guennadi Liakhovetski
8a6afb9a95 spi/spi_sh_msiof: fix wrong address calculation, which leads to an Oops
NULL + <small offset> != NULL, but reading from that <small offset> address
is usually not a very good idea and often leads to problems, like kernel
Oopses in this case, easily reproducible by writing to an SD-card, used in
SPI mode.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-21 09:26:24 -07:00
Grant Likely
c9e358dfc4 driver-core: remove conditionals around devicetree pointers
Having conditional around the of_match_table and the of_node pointers
turns out to make driver code use ugly #ifdef blocks.  Drop the
conditionals and remove the #ifdef blocks from the affected drivers.

Also tidy up minor whitespace issues within the same hunks.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-01-21 09:24:48 -07:00
Linus Torvalds
5d7e8af3c5 Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (26 commits)
  MIPS: Malta: enable Cirrus FB console
  MIPS: add CONFIG_VIRTUALIZATION for virtio support
  MIPS: Implement __read_mostly
  MIPS: ath79: add common WMAC device for AR913X based boards
  MIPS: ath79: Add initial support for the Atheros AP81 reference board
  MIPS: ath79: add common SPI controller device
  SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
  MIPS: ath79: add common GPIO buttons device
  MIPS: ath79: add common watchdog device
  MIPS: ath79: add common GPIO LEDs device
  MIPS: ath79: add initial support for the Atheros PB44 reference board
  MIPS: ath79: utilize the MIPS multi-machine support
  MIPS: ath79: add GPIOLIB support
  MIPS: Add initial support for the Atheros AR71XX/AR724X/AR931X SoCs
  MIPS: jump label: Add MIPS support.
  MIPS: Use WARN() in uasm for better diagnostics.
  MIPS: Optimize TLB handlers for Octeon CPUs
  MIPS: Add LDX and LWX instructions to uasm.
  MIPS: Use BBIT instructions in TLB handlers
  MIPS: Declare uasm bbit0 and bbit1 functions.
  ...
2011-01-18 14:28:48 -08:00
Gabor Juhos
8efaef4dc8 SPI: Add SPI controller driver for the Atheros AR71XX/AR724X/AR913X SoCs
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2011-01-18 19:30:27 +01:00
Guennadi Liakhovetski
d95defaca7 spi/spi_sh_msiof: fix a wrong free_irq() parameter
Without this fix reloading of the driver is impossible.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-17 10:17:36 -07:00
Viresh Kumar
94a1b6d8eb spi/amba-pl022: fixing compilation warning.
clk_freq is used uninitialized in pl022_setup routine. This patch
fix compilation warning for using uninitialized variable

Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-14 15:26:07 -07:00
Grant Likely
42a9fa9957 Merge branch 'devicetree/next' into spi/next 2011-01-14 12:09:49 -07:00
Abhilash Kesavan
5f35765d83 spi: Enable SPI driver for S5P6440 and S5P6450
This patch enables the existing S3C64XX series SPI driver for S5P64X0
and removed dependency on EXPERIMENTAL because we don't need it now.

v3: Changed dependency of S3C64XX_DMA
v2: Removed dependency on EXPERIMENTAL

Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Acked-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-14 01:01:51 -07:00
Linus Torvalds
008d23e485 Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
  Documentation/trace/events.txt: Remove obsolete sched_signal_send.
  writeback: fix global_dirty_limits comment runtime -> real-time
  ppc: fix comment typo singal -> signal
  drivers: fix comment typo diable -> disable.
  m68k: fix comment typo diable -> disable.
  wireless: comment typo fix diable -> disable.
  media: comment typo fix diable -> disable.
  remove doc for obsolete dynamic-printk kernel-parameter
  remove extraneous 'is' from Documentation/iostats.txt
  Fix spelling milisec -> ms in snd_ps3 module parameter description
  Fix spelling mistakes in comments
  Revert conflicting V4L changes
  i7core_edac: fix typos in comments
  mm/rmap.c: fix comment
  sound, ca0106: Fix assignment to 'channel'.
  hrtimer: fix a typo in comment
  init/Kconfig: fix typo
  anon_inodes: fix wrong function name in comment
  fix comment typos concerning "consistent"
  poll: fix a typo in comment
  ...

Fix up trivial conflicts in:
 - drivers/net/wireless/iwlwifi/iwl-core.c (moved to iwl-legacy.c)
 - fs/ext4/ext4.h

Also fix missed 'diabled' typo in drivers/net/bnx2x/bnx2x.h while at it.
2011-01-13 10:05:56 -08:00
Yong Shen
77e7bc6194 spi/imx: Add i.MX53 support
1. Change the Kconfig to include i.MX53
2. add devtype entry for i.MX53

Signed-off-by: Yong Shen <yong.shen@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-12 22:50:54 -07:00
Jamie Iles
50c01fc355 spi/dw_spi: don't treat NULL clk as an error
clk_get() returns a struct clk cookie to the driver and some platforms
may return NULL if they only support a single clock.  clk_get() has only
failed if it returns a ERR_PTR() encoded pointer.

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-11 08:20:07 -07:00
Jamie Iles
76d9cc454a spi: tegra: don't treat NULL clk as an error
Some platforms have been known to return NULL from clk_get() if they
support only a single struct clk.  Whilst tegra doesn't do this, make
the drivers consistent with others.

Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-10 16:44:01 -07:00
Linus Torvalds
c8940eca75 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  spi / PM: Support dev_pm_ops
  PM: Prototype the pm_generic_ operations
  PM / Runtime: Generic resume shouldn't set RPM_ACTIVE unconditionally
  PM: Use dev_name() in core device suspend and resume routines
  PM: Permit registration of parentless devices during system suspend
  PM: Replace the device power.status field with a bit field
  PM: Remove redundant checks from core device resume routines
  PM: Use a different list of devices for each stage of device suspend
  PM: Avoid compiler warning in pm_noirq_op()
  PM: Use pm_wakeup_pending() in __device_suspend()
  PM / Wakeup: Replace pm_check_wakeup_events() with pm_wakeup_pending()
  PM: Prevent dpm_prepare() from returning errors unnecessarily
  PM: Fix references to basic-pm-debugging.txt in drivers-testing.txt
  PM / Runtime: Add synchronous runtime interface for interrupt handlers (v3)
  PM / Hibernate: When failed, in_suspend should be reset
  PM / Hibernate: hibernation_ops->leave should be checked too
  Freezer: Fix a race during freezing of TASK_STOPPED tasks
  PM: Use proper ccflag flag in kernel/power/Makefile
  PM / Runtime: Fix comments to match runtime callback code
2011-01-10 08:14:53 -08:00
Linus Torvalds
021db8e2bd Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (77 commits)
  spi/omap: Fix DMA API usage in OMAP MCSPI driver
  spi/imx: correct the test on platform_get_irq() return value
  spi/topcliff: Typo fix threhold to threshold
  spi/dw_spi Typo change diable to disable.
  spi/fsl_espi: change the read behaviour of the SPIRF
  spi/mpc52xx-psc-spi: move probe/remove to proper sections
  spi/dw_spi: add DMA support
  spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
  spi/dw_spi: Fix too short timeout in spi polling loop
  spi/pl022: convert running variable
  spi/pl022: convert busy flag to a bool
  spi/pl022: pass the returned sglen to the DMA engine
  spi/pl022: map the buffers on the DMA engine
  spi/topcliff_pch: Fix data transfer issue
  spi/imx: remove autodetection
  spi/pxa2xx: pass of_node to spi device and set a parent device
  spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
  spi/pxa2xx: Add chipselect support for Sodaville
  spi/pxa2xx: Consider CE4100's FIFO depth
  spi/pxa2xx: Add CE4100 support
  ...
2011-01-07 17:08:46 -08:00
Russell King - ARM Linux
07fe035170 spi/omap: Fix DMA API usage in OMAP MCSPI driver
Running the latest kernel on the 4430SDP board with DMA API debugging
enabled results in this:

WARNING: at lib/dma-debug.c:803 check_unmap+0x19c/0x6f0()
NULL NULL: DMA-API: device driver tries to free DMA memory it has not allocated
[device address=0x000000008129901a] [size=260 bytes]
Modules linked in:
Backtrace:
[<c003cbe0>] (dump_backtrace+0x0/0x10c) from [<c0278da8>] (dump_stack+0x18/0x1c)
 r7:c1839dc0 r6:c0198578 r5:c0304b17 r4:00000323
[<c0278d90>] (dump_stack+0x0/0x1c) from [<c005b158>] (warn_slowpath_common+0x58/0x70)
[<c005b100>] (warn_slowpath_common+0x0/0x70) from [<c005b214>] (warn_slowpath_fmt+0x38/0x40)
 r8:c1839e40 r7:00000000 r6:00000104 r5:00000000 r4:8129901a
[<c005b1dc>] (warn_slowpath_fmt+0x0/0x40) from [<c0198578>] (check_unmap+0x19c/0x6f0)
 r3:c03110de r2:c0304e6b
[<c01983dc>] (check_unmap+0x0/0x6f0) from [<c0198cd8>] (debug_dma_unmap_page+0x74/0x80)
[<c0198c64>] (debug_dma_unmap_page+0x0/0x80) from [<c01d5ad8>] (omap2_mcspi_work+0x514/0xbf0)
[<c01d55c4>] (omap2_mcspi_work+0x0/0xbf0) from [<c006dfb0>] (process_one_work+0x294/0x400)
[<c006dd1c>] (process_one_work+0x0/0x400) from [<c006e50c>] (worker_thread+0x220/0x3f8)
[<c006e2ec>] (worker_thread+0x0/0x3f8) from [<c00738d0>] (kthread+0x88/0x90)
[<c0073848>] (kthread+0x0/0x90) from [<c005e924>] (do_exit+0x0/0x5fc)
 r7:00000013 r6:c005e924 r5:c0073848 r4:c1829ee0
---[ end trace 1b75b31a2719ed20 ]---

I've no idea why this driver uses NULL for dma_unmap_single instead of
the &spi->dev that is laying around just waiting to be used in that
function - but it's an easy fix.

Also replace this comment with a FIXME comment:
                /* Do DMA mapping "early" for better error reporting and
                 * dcache use.  Note that if dma_unmap_single() ever starts
                 * to do real work on ARM, we'd need to clean up mappings
                 * for previous transfers on *ALL* exits of this loop...
                 */
as the comment is not true - we do work in dma_unmap() functions,
particularly on ARMv6 and above.  I've corrected the existing unmap
functions but if any others are required they must be added ASAP.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-07 13:44:24 -07:00
Richard Genoud
735759389b spi/imx: correct the test on platform_get_irq() return value
The test "if (spi_imx->irq <= 0)" is not testing the IRQ value, but
the return value of platform_get_irq().  As platform_get_irq() can
return an error (-ENXIO) or the IRQ value it found, the test should be
"if (spi_imx->irq < 0)"

[grant.likely: Note: In general, Linux irq number 0 should also mean
no irq, but arm still allows devices to be assigned 0, and the imx
platform uses 0 for one of the spi devices, so this patch is needed
for the device to work]

Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2011-01-07 10:01:23 -07:00
Justin P. Mattock
77e58efd13 spi/topcliff: Typo fix threhold to threshold
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-31 17:49:30 -07:00
Justin P. Mattock
2f263d9d4f spi/dw_spi Typo change diable to disable.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-30 23:44:55 -07:00
Jate Sujjavanich
0bc463426a spi/m68knommu: Coldfire QSPI platform support
After grabbing a msg from the msgq, the mcfqspi_work function calls
list_del_init on the mcfqspi->msgq which unintentionally deletes the rest
of the list before it can be processed. If qspi call was made using
spi_sync, this can result in a process hang.

Signed-off-by: Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Acked-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-29 23:28:25 -07:00
Mingkai Hu
477ca3ad6a spi/fsl_espi: change the read behaviour of the SPIRF
The user must read N bytes of SPIRF (1 <= N <= 4) that do not exceed the
amount of data in the receive FIFO, so read the SPIRF byte by byte when
the data in receive FIFO is less than 4 bytes.

On Simics, when read N bytes that exceed the amout of data in receive
FIFO, we can't read the data out, that is we can't clear the rx FIFO,
then the CPU will loop on the espi rx interrupt.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-29 23:04:46 -07:00
Gregory CLEMENT
42ce7fd631 spi/omap2_mcspi.c: Force CS to be in inactive state after off-mode transition
When SPI wake up from OFF mode, CS is in the wrong state: force it to the
inactive state.

During the system life, I monitored the CS behavior using a oscilloscope.
I also activated debug in omap2_mcspi, so I saw when driver disable the clocks
and restore context when device is not used.Each time the CS was in the correct
state.  It was only when system was put suspend to ram with off-mode activated
that on resume the CS was in wrong state( ie activated).

Changelog:
* Change from v1 to v2:
  - Rebase on linus/master (after 2.6.37-rc1)
  - Do some clean-up and fix indentation on both patches
  - Add more explanations for patch 2

* Change from v2 to v3:
  - Use directly resume function of spi_master instead of using function
  - from spi_device as Grant Likely pointed it out.
  - Force this transition explicitly for each CS used by a device.

* Change from v3 to v4:
  - Patch clean-up according to Kevin Hilman and checkpatch.
  - Now force CS to be in inactive state only if it was inactive when it was
    suspended.

* Change from v4 to v5:
  - Rebase on linus/master (after 2.6.37-rc3)
  - Collapse some lines as pointed by Grant Likely
  - Fix a spelling

* Change from v5 to v6:
  - Rebase on linus/master (after 2.6.37-rc7)
  - Use CONFIG_SUSPEND instead of CONFIG_PM
  - Didn't use legacy PM methods anymore. Instead, add a struct dev_pm_ops and
    add the resume method there.
  - Fix multi-line comment style

* Change from v6 to v7:
  - Rebase on linus/master (after 2.6.37-rc8)
  - Drop an extra line

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-29 15:13:05 -07:00
Grant Likely
94a544a4e8 Merge branch 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
  spi/pxa2xx: register driver properly
  spi/pxa2xx: add support for shared IRQ handler
  spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
  arm/pxa2xx: reorgazine SSP and SPI header files
  spi/pxa2xx: Add CE4100 support
  spi/pxa2xx: Consider CE4100's FIFO depth
  spi/pxa2xx: Add chipselect support for Sodaville
  spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
  spi/pxa2xx: pass of_node to spi device and set a parent device
2010-12-29 01:05:50 -07:00
Grant Likely
496a2e360a Merge branch 'for-grant' of git://arago-project.org/git/projects/linux-davinci into spi/next
* 'for-grant' of git://arago-project.org/git/projects/linux-davinci into spi/next
   spi: davinci: fix checkpatch errors
   spi: davinci: whitespace cleanup
   spi: davinci: remove unused variable 'pdata'
   spi: davinci: set chip-select mode in SPIDEF only once
   spi: davinci: enable both activation and deactivation of chip-selects
   spi: davinci: remove unnecessary data transmit on CS disable
   spi: davinci: enable GPIO lines to be used as chip selects
   spi: davinci: simplify prescalar calculation
   spi: davinci: remove 'wait_enable' platform data member
   spi: davinci: make chip-slect specific parameters really chip-select specific
   spi: davinci: consolidate setup of SPIFMTn in one function
   spi: davinci: setup chip-select timers values only if timer enabled
   spi: davinci: add support for wait enable timeouts
   spi: davinci: remove unused members of davinci_spi_slave
   spi: davinci: eliminate the single member structure davinci_spi_slave
   spi: davinci: eliminate unnecessary update of davinci_spi->count
   spi: davinci: simplify calculation of edma acount value
   spi: davinci: check for NULL buffer pointer before using it
   spi: davinci: remove unnecessary disable of SPI
   spi: davinci: remove unnecessary 'count' variable in driver private data
   spi: davinci: remove unnecessary completion variable initialization
   spi: davinci: remove non-useful interrupt mode support
   spi: davinci: simplify poll mode transfers
   spi: davinci: add support for interrupt mode
   spi: davinci: configure the invariable bits in spipc0 only once
   spi: davinci: remove unnecessary function davinci_spi_bufs_prep()
   spi: davinci: remove unnecessary call to davinci_spi_setup_transfer()
   spi: davinci: do not store DMA channel information per chip select
   spi: davinci: always start transmit DMA
   spi: davinci: do not use temporary buffer if no transmit data provided
   spi: davinci: always start receive DMA
   spi: davinci: use edma_write_slot() to setup EDMA PaRAM slot
   spi: davinci: fix DMA event generation stoppage
   spi: davinci: fix EDMA CC errors at end of transfers
   spi: davinci: handle DMA completion errors correctly
   spi: davinci: remove usage of additional completion variables for DMA
   spi: davinci: let DMA operation be specified on per-device basis
   spi: davinci: remove non-useful "clk_internal" platform data
   spi: davinci: enable and power-up SPI only when required
   spi: davinci: setup the driver owner
   spi: davinci: add additional comments
   spi: davinci: add EF Johnson Technologies copyright
   spi: davinci: removed unused #defines
   spi: davinci: remove unnecessary typecast
   spi: davinci: do not treat Tx interrupt being set as error
   spi: davinci: do not allocate DMA channels during SPI device setup
   spi: davinci: remove unnecessary private data member 'region_size'
   spi: davinci: shorten variable names
   spi: davinci: kconfig: add manufacturer name to prompt string
2010-12-29 00:47:38 -07:00
Mark Brown
3ae22e8c8a spi / PM: Support dev_pm_ops
Allow SPI drivers to use runtime PM and other dev_pm_ops features by
implementing dev_pm_ops for the bus. The existing bus specific suspend
and resume functions will be called if a driver does not provide dev_pm_ops
allowing for transition to the new model.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-12-25 15:32:27 +01:00
Linus Torvalds
d3c7e1ab04 Merge branch 'merge' of git://git.secretlab.ca/git/linux-2.6
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
  spi/mpc52xx-spi: fix annotation for remove()-pointer
  spi/fsl_espi: fix wrong setting of the address in the command buffer
  spi/fsl_espi: change the read behaviour of the SPIRF
  of/i2c: Fix request module by alias
  powerpc/mpc5200: include fs.h in mpc52xx_gpt.c
2010-12-24 13:00:37 -08:00
Wolfram Sang
5aa68b8595 spi/mpc52xx-psc-spi: move probe/remove to proper sections
Probe/remove should be in __devinit/__devexit. Found by a section-mismatch
warning. Also, copy do_remove() over to remove().

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-24 11:18:34 -07:00
Wolfram Sang
4bdac7da52 spi/mpc52xx-spi: fix annotation for remove()-pointer
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-24 01:57:17 -07:00
Mingkai Hu
0dd2c96f19 spi/fsl_espi: fix wrong setting of the address in the command buffer
Or else we can't operate on the right address when the trans length
is greater than 65535.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-24 01:53:57 -07:00
Mingkai Hu
e6289d63a6 spi/fsl_espi: change the read behaviour of the SPIRF
The user must read N bytes of SPIRF (1 <= N <= 4) that do not exceed the
amount of data in the receive FIFO, so read the SPIRF byte by byte when
the data in receive FIFO is less than 4 bytes.

On Simics, when read N bytes that exceed the amount of data in receive
FIFO, we can't read the data out, that is we can't clear the rx FIFO,
then the CPU will loop on the espi rx interrupt.

Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-24 01:53:41 -07:00
Feng Tang
7063c0d942 spi/dw_spi: add DMA support
dw_spi driver in upstream only supports PIO mode, and this patch
will support it to cowork with the Designware dma controller used
on Intel Moorestown platform, at the same time it provides a general
framework to support dw_spi core to cowork with dma controllers on
other platforms

It has been tested with a Option GTM501L 3G modem and Infenion 60x60
modem. To use DMA mode, DMA controller 2 of Moorestown has to be enabled

Also change the dma interface suggested by Linus Walleij.

Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
[Typo fix and renames to match intel_mid_dma renaming]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-24 01:23:25 -07:00
Feng Tang
79290a2aa2 spi/dw_spi: change to EXPORT_SYMBOL_GPL for exported APIs
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-24 01:09:21 -07:00
Feng Tang
ebf45b7d02 spi/dw_spi: Fix too short timeout in spi polling loop
The SPI polling loop timeout only works with HZ=100 as the loop was
actually too short.

Also add appropriate cpu_relax() in the busy wait loops...

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-24 01:08:42 -07:00
Linus Walleij
5e8b821de3 spi/pl022: convert running variable
This variable is a bool but defined an int and defined completely
backwards. This makes the code more readable.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-23 21:06:47 -07:00
Linus Walleij
dec5a581eb spi/pl022: convert busy flag to a bool
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-23 21:06:47 -07:00
Linus Walleij
082086f2ce spi/pl022: pass the returned sglen to the DMA engine
The sglen return by the dma_map_sg() should be passed to the DMA
engine, not the one passed in. If we one day have a DMA mapper
that can coalesce entries, this will bug due to a too large
number of entries being passed in.

Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-23 21:06:46 -07:00
Linus Walleij
b729889686 spi/pl022: map the buffers on the DMA engine
The struct device for the DMA engine is the apropriate one to use
when mapping/unmapping buffers. This is because the memory which
is addressable by DMA is determined by the DMA engine rather than
the device.

Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-23 21:06:43 -07:00
Tomoya MORINAGA
9d32af66aa spi/topcliff_pch: Fix data transfer issue
It seems spi_topcliff_pch of linux-2.6.37-rc6 degraded by previous patch.
In fact, data transfer fails on evaluation board testing.
I found like the following register miss-setting line.
Using this patch, I have confirmed data transfer can work well.

Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-23 20:30:11 -07:00
Uwe Kleine-König
893421745a spi/imx: remove autodetection
There are no machines in-tree that still use the driver
name as device name.  So save a few bytes and remove it.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-12-23 19:18:36 -07:00
Sebastian Andrzej Siewior
97dbf37d89 drivers/spi/spi.c: don't release the spi device twice
This was fixed by David Lamparter in v2.6.36-rc5 3486008 ("spi: free
children in spi_unregister_master, not siblings") and broken again in
v2.6.37-rc1~2^2~4 during the merge of 2b9603a0 ("spi: enable
spi_board_info to be registered after spi_master").

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-12-22 19:43:34 -08:00
Jiri Kosina
4b7bd36470 Merge branch 'master' into for-next
Conflicts:
	MAINTAINERS
	arch/arm/mach-omap2/pm24xx.c
	drivers/scsi/bfa/bfa_fcpim.c

Needed to update to apply fixes for which the old branch was too
outdated.
2010-12-22 18:57:02 +01:00
Grant Likely
752a4a95e3 Merge commit 'v2.6.37-rc7' into spi/next 2010-12-22 00:10:01 -07:00
Major Lee
3d0b6087f3 dw_spi: Fix missing final read in some polling situations
There is a possibility that the last word of a transaction will be lost
if data is not ready.  Re-read in poll_transfer() to solve this issue
when poll_mode is enabled.

Verified on SPI touch screen device.

Signed-off-by: Major Lee <major_lee@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-12-14 18:48:59 -08:00
Sebastian Andrzej Siewior
21486af0f3 spi/pxa2xx: pass of_node to spi device and set a parent device
the of_node will auto-publish devices which are added to the device
tree.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
2010-12-02 17:55:13 +01:00
Sebastian Andrzej Siewior
579d3bb2ac spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
After all TX bytes are sent, the driver spins while the SPI core is busy
and then it spins for a "short" period of time until RX bytes are
available.
On Sodavile the busy flag disappears pretty quick and after that it
takes approx ~130ms (sometimes less but not much) until there are bytes
available in the RX FIFO.
This patch removes the busy loop and modifies the RX threshould so we
get woken up once the remainings bytes arrived.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-02 17:55:13 +01:00
Sebastian Andrzej Siewior
2a8626a9e2 spi/pxa2xx: Add chipselect support for Sodaville
The SPI core on Sodaville supports chip selects. Its configuration
moved into the SSSR register at bit 0 and 1. Thus Sodaville can be hooked
up with up to 4 devices.
This patch ensures that the bits which are otherwiese reserved are only
touched on Sodaville and not on any other PXAs. Also it makes sure that
the status register does not lose the CS information while clearing the
ROR bit.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-02 17:55:12 +01:00
Sebastian Andrzej Siewior
d0777f2c3e spi/pxa2xx: Consider CE4100's FIFO depth
For PXA the default threshold is FIFO_DEPTH / 2. Adjust this value for
CE4100.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-01 13:48:30 +01:00
Sebastian Andrzej Siewior
d6ea3df0d4 spi/pxa2xx: Add CE4100 support
Sodaville's SPI controller is very much the same as in PXA25x. The
difference:
- The RX/TX FIFO is only 4 words deep instead of 16
- No DMA support
- The SPI controller offers a CS functionality

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-01 13:48:30 +01:00
Sebastian Andrzej Siewior
8348c259dd arm/pxa2xx: reorgazine SSP and SPI header files
The PXA-SPI driver relies on some files / defines which are arm specific
and are within the ARM tree. The CE4100 SoC which is x86 has also the
SPI core.
This patch moves the ssp and spi files from arm/mach-pxa and plat-pxa to
include/linux where the CE4100 can access them.

This move got verified by building the following defconfigs:
   cm_x2xx_defconfig corgi_defconfig em_x270_defconfig ezx_defconfig
   imote2_defconfig pxa3xx_defconfig spitz_defconfig zeus_defconfig
   raumfeld_defconfig magician_defconfig

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-01 12:18:33 +01:00
Sebastian Andrzej Siewior
4a25605fb7 spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-01 12:18:32 +01:00
Sebastian Andrzej Siewior
49cbb1e0b6 spi/pxa2xx: add support for shared IRQ handler
This is required in case the interrupt line is shared with other
devices.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-12-01 12:18:31 +01:00
Jean-Christophe PLAGNIOL-VILLARD
214b574ab8 atmel_spi: fix warning In function 'atmel_spi_dma_map_xfer'
passing argument 2 of 'dma_map_single' discards qualifiers from pointer target type

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
2010-11-30 17:23:24 +01:00
Sebastian Andrzej Siewior
fbd29a14af spi/pxa2xx: register driver properly
use platform_driver_register instead of platform_driver_probe. The
latter only checks available devices at the time of calling. So if a
device gets inserter at a later point in time then the driver will never
play with it.

Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
2010-11-26 11:29:02 +01:00
Sekhar Nori
23ce17adb7 spi: davinci: kconfig: add manufacturer name to prompt string
Add manufacturer name to the Kconfig prompt string and move
the controller name to the begining of the prompt.

This helps locate the driver easily among the list of existing
drivers.

While at it, also add information about being able to build
the driver as module.

Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:38 +05:30
Sekhar Nori
212d4b6965 spi: davinci: shorten variable names
Shorten names of local variables and structure members where
possible.

Local variables:

* 'davinci_spi' is being renamed 'dspi'
* 'davinci_spi_dma' is being renamed 'dma'

Structure members:

* 'dma_{tx|rx}_channel' is being renamed '{tx|rx}_channel'
  since the structure containing them is already called
  'davinci_spi_dma'

* 'davinci_spi_dma' in 'davinci_spi' structure is being
  renamed 'dma'

Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:38 +05:30
Sekhar Nori
0e0eae4d1c spi: davinci: remove unnecessary private data member 'region_size'
Remove unnecesary private data member 'region_size'
being used to store the size of SPI memory region.

Instead, get the memory resource size directly from
the platform data.

Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:37 +05:30
Brian Niebuhr
43abb11ba5 spi: davinci: add EF Johnson Technologies copyright
Add copyright for EF Johnson Technologies since the driver
has been majorly overhauled by Brian.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:37 +05:30
Brian Niebuhr
035540f6ea spi: davinci: add additional comments
Add comments describing the platform data members
and per-chip-select SPI configuration structure.

Also, add some comments describing the what happens
during the driver probe.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:37 +05:30
Brian Niebuhr
d8c174cdeb spi: davinci: setup the driver owner
Setup the owner member of the platform driver to THIS_MODULE
instead of leaving it NULL.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:37 +05:30
Brian Niebuhr
3f27b57c16 spi: davinci: enable and power-up SPI only when required
Enable SPI only when active transfers are in progress. Keep
it in local low power when not in use.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:36 +05:30
Brian Niebuhr
3409e408ab spi: davinci: remove non-useful "clk_internal" platform data
The "clk_internal" platform data member which contols the
CLKMOD bit in Global Control Register 1 is not useful
since CLKMOD needs be set to 1 *always* to ensure master
mode operation.

Remove this platform data.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:36 +05:30
Brian Niebuhr
87467bd905 spi: davinci: let DMA operation be specified on per-device basis
Let DMA operation be specified on a per-device basis instead
of selecting it once during probe.

A side effect of this is the need to combine the PIO and DMA buffer
txrx_bufs routine. This is good since they anyway share some common
functionality.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:36 +05:30
Brian Niebuhr
6dbd29b27b spi: davinci: remove usage of additional completion variables for DMA
The DMA code does not use the existing completion variable 'done'
which is being used for interrupt mode transfers. Instead it uses
two different completion variables specific to DMA mode transfers.

Eliminate the usage of new completion variables for DMA mode and
use the existing completion variable.

[nsekhar@ti.com: To make this process easy, eliminate the two
different DMA completion callback functions for tx and rx and
use a single callback function instead]

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:35 +05:30
Brian Niebuhr
9b189fd758 spi: davinci: handle DMA completion errors correctly
Do not simply clean the DMA channel on a DMA completion
error. Instead, use wcount and rcount members of davinci_spi
to detecion non-completion of DMA and signal EIO to the
application.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:35 +05:30
Brian Niebuhr
523c37e700 spi: davinci: fix EDMA CC errors at end of transfers
Use a dummy param slot linked to itself to take care of the
extra "sync event" that gets sent to EDMA controller after
the last byte has been transferred.

The dummy PaRAM slot that is linked to the actual DMA PaRAM
slot "absorbs" this event and prevents a EDMA CC error to
be asserted.

Without this provision, the EDMA CC error would be asserted
because the channel PaRAM would be empty after the transfer
and EDMA would not know what to make out of the extra sync
event.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:35 +05:30
Sekhar Nori
903ca25b21 spi: davinci: do not allocate DMA channels during SPI device setup
Do not allocate (and de-allocate) SPI DMA channels during setup
(and cleanup) for each SPI device. Instead, allocate the DMA
channels once duing probe and use them for the life time of
the driver.

This makes sense since there are dedicated DMA channels meant
for SPI use.

This also helps remove the unnecessary DMA "sync_dev" variables
being used to store DMA channel information.

Also, the "use_dma" platform variable is now eliminated since
it is possible to check if the platform supports DMA or not
based upon whether DMA resources can be found or not.

Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:34 +05:30
Brian Niebuhr
a4f4497b86 spi: davinci: fix DMA event generation stoppage
Do not stop SPI DMA event generation in either transmit or
receive DMA event call back because the single setting affects
both transmit and receive event generation.

Depending on the order in which the callbacks happen, transmit
or receive events can get unintentionally stalled.

Instead, disable event generation once after both the transmit
and receive DMA completes.

While at it, remove the largely under-used function to set or
clear DMA event generation.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:34 +05:30
Brian Niebuhr
49fc3f497d spi: davinci: use edma_write_slot() to setup EDMA PaRAM slot
Currently a series of EDMA API calls are being made to setup
various aspects of EDMA PaRAM slots for receive and transmit.

Instead setup the PaRAM using a local structure and write once
to the hardware using edma_write_slot()

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:34 +05:30
Brian Niebuhr
e91c659bbc spi: davinci: always start receive DMA
In keeping with the full duplex nature of the SPI bus. Always
start receive DMA along with transmit DMA.

If there is no receive buffer provided with the transfer, use
a temporary buffer to receive the data to be thrown away.

[michael.williamson@criticallink.com: receive DMA size should
be same as transfer length to avoid hang-up when transfer length
is smaller than temporary rx buffer size (rx buffer not provided)]

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:34 +05:30
Brian Niebuhr
d3f7141cbf spi: davinci: do not use temporary buffer if no transmit data provided
Remove usage of temporary buffer when no transmit data is provided.
Instead, use the transmit register itself as the source of data.

By choosing the transmit register itself as the source of data, this
patch helps remove unnecessary accesses to memory when no real data
is being transmitted.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:33 +05:30
Brian Niebuhr
c29e3c60e7 spi: davinci: always start transmit DMA
Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.

The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.

However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.

Fix this by starting transmit DMA always.

This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:33 +05:30
Brian Niebuhr
96fd881f22 spi: davinci: do not store DMA channel information per chip select
Do not store DMA channel related information per chip-select since
that information does not depend on the chip select.

The same DMA channels can be used for transfers on all chip-selects
since the transfer happens one-at-a-time.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:33 +05:30
Brian Niebuhr
b23a5d4691 spi: davinci: remove unnecessary call to davinci_spi_setup_transfer()
Remove unnecessary call to davinci_spi_setup_transfer() at the end
of davinci_spi_setup().

davinci_spi_setup_transfer() is registered as the setup_transfer
callback for the bitbang layer and is called independently by
the bitbang layer to setup the transfer before it begins.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:33 +05:30
Brian Niebuhr
be88471b96 spi: davinci: remove unnecessary function davinci_spi_bufs_prep()
The function davinci_spi_bufs_prep() is doing stuff that
davinci_spi_setup() is doing. Eliminate it and move the work
to davinci_spi_setup()

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:32 +05:30
Brian Niebuhr
f34bd4cc68 spi: davinci: configure the invariable bits in spipc0 only once
Configure the data-in, data-out and clock functionality pins
in SPIPC0 register only once during probe. No need to set these
bits for each transfer.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:31 +05:30
Brian Niebuhr
e0d205e991 spi: davinci: add support for interrupt mode
Add support for SPI interrupt mode operation.

Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.

Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:30 +05:30
Brian Niebuhr
839c996ca8 spi: davinci: simplify poll mode transfers
Use the fact that the get_tx and get_rx can now cope with
NULL buffer pointers to simplify the poll mode transfer
code.

While at it, check for SPI errors every transfer rather than
at the end of the whole transfer.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:30 +05:30
Brian Niebuhr
cf90fe7350 spi: davinci: remove non-useful interrupt mode support
The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.

Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:29 +05:30
Brian Niebuhr
47f44671c0 spi: davinci: remove unnecessary completion variable initialization
The completion variable 'done' is unnecessarly initialized by
the function davinci_spi_bufs_dma() where as it is not used
for DMA transfers at all.

Remove the unnecessary initialization.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:29 +05:30
Sekhar Nori
134e32b979 spi: davinci: do not treat Tx interrupt being set as error
In davinci_spi_check_error(), Tx interrupt being set is
treated as error. This function is only meant to flag
bus error conditions and Tx interrupt being set at that
point is not a bus error but rather a driver bug.

Stop checking for Tx interrupt and flagging that as an
IO error.

Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:29 +05:30
Brian Niebuhr
f2bf4e8493 spi: davinci: remove unnecessary 'count' variable in driver private data
The variable count in DaVinci SPI driver's private data is
largely unused and its minor use can easily be eliminated.

Remove the variable.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:29 +05:30
Brian Niebuhr
fab89ea330 spi: davinci: remove unnecessary disable of SPI
In the davinci_spi_bufs_dma() function, SPI is briefly disabled
before enabling it immediately back again.

Remove this unnecessary disable.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:28 +05:30
Brian Niebuhr
53d454a170 spi: davinci: check for NULL buffer pointer before using it
In the davinci_spi_{tx|rx}_u{8|16}() functions, check for
buffer pointer being valid before using it. While providing
for better error checking, this change will help simplify
code in the caller.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:28 +05:30
Brian Niebuhr
b7ab24a0da spi: davinci: simplify calculation of edma acount value
The EDMA acount (called data_type in davinci_spi_bufs_dma())
is simply the bytes_per_word obtained in the transfer setup
function. The current code calculates the acount value from
bytes_per_word in a convoluted manner. Simplify the code.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:28 +05:30
Brian Niebuhr
6321be60ed spi: davinci: eliminate unnecessary update of davinci_spi->count
The count member of davinci_spi is internal to the driver and
is not shared with framework. Eliminate its unnecessary update.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:27 +05:30
Brian Niebuhr
cda987ebb8 spi: davinci: eliminate the single member structure davinci_spi_slave
The struct davinci_spi_slave has a single member. Eliminate it
and store the per-chipselect data in struct davinci_spi directly.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:27 +05:30
Brian Niebuhr
b6c4eeac5b spi: davinci: remove unused members of davinci_spi_slave
Several members of struct davinci_spi_slave are unused in code.
Remove such members.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:27 +05:30
Brian Niebuhr
7abbf23c59 spi: davinci: add support for wait enable timeouts
Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).

While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:27 +05:30
Brian Niebuhr
fd764463fe spi: davinci: setup chip-select timers values only if timer enabled
Setup chip-select timers values only if timer is enabled
(timer_disbled in spi configuration is false).

As a nice side effect, this patch removes code duplicated in
davinci_spi_bufs_pio() and davinci_spi_bufs_dma().

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:26 +05:30
Brian Niebuhr
25f33512f6 spi: davinci: consolidate setup of SPIFMTn in one function
Consolidate the setup of SPIFMTn register under
davinci_spi_setup_transfer() simplifying the code
and avoiding unnecessary reads and writes to the
register.

The two inline functions {set|clear}_fmt_bits() can
be eliminated because of this.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:26 +05:30
Brian Niebuhr
53a31b07c5 spi: davinci: make chip-slect specific parameters really chip-select specific
Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.

Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:26 +05:30
Brian Niebuhr
472880c73d spi: davinci: remove 'wait_enable' platform data member
The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.

The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:25 +05:30
Brian Niebuhr
7fe0092b1f spi: davinci: simplify prescalar calculation
Simplify pre-scalar calculation and move it into a seprate
function.

Refuse to correct invalid pre-scalar values silently as this
might lead to unexpected bugs and lower performance. Instead
an error will force users to dig into the root-cause of the
issue.

While at it, remove some device specific checks on the maximum
SPI frequency. As the driver supports the SPI interface
implemented on various devices, it should only take care of core
SPI limitations and leave the device specific handling to platform
code.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:25 +05:30
Brian Niebuhr
23853973d9 spi: davinci: enable GPIO lines to be used as chip selects
Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.

This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:25 +05:30
Brian Niebuhr
cfbc5d1d8f spi: davinci: remove unnecessary data transmit on CS disable
On TI DaVinci's SPI controller, the SPIDAT1 register which
controls the chip slect status, also has data transmit register
in the lower 16 bits. Writing to the whole 32-bits triggers
an additional data transmit every time the chip select is disabled.

While most SPI slaves cope-up with this, some cannot. This
patch fixes this by doing a 16-bit write on the upper half
of the SPIDAT1 register

While at it, group the SPIGCR1 register related defines seperately
from SPIDAT1 register defines.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:24 +05:30
Brian Niebuhr
7978b8c385 spi: davinci: enable both activation and deactivation of chip-selects
Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.

With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().

Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:24 +05:30
Brian Niebuhr
843a713bc5 spi: davinci: set chip-select mode in SPIDEF only once
Quit writing the same constant value determining the chip-select
mode when no transmissions are in progress in davinci_spi_chipelect().

Instead just setup the SPIDEF register once during probe.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:24 +05:30
Sekhar Nori
50356dd7c1 spi: davinci: remove unnecessary typecast
The typecasting of SPI base address to davinci_spi_reg is
unused.

Remove it.

Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:24 +05:30
Sekhar Nori
8e206f1cbd spi: davinci: removed unused #defines
Remove unused defines from code which should help
in easy reading of code.

Also, use the opportuinity to keep the SPIGCR1
register defines together.

Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:23 +05:30
Brian Niebuhr
c3c475c235 spi: davinci: remove unused variable 'pdata'
The 'pdata' variable is unused in couple of routines.

Remove such occurences.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:23 +05:30
Brian Niebuhr
778e261ed6 spi: davinci: whitespace cleanup
Cleanup unnecessary white space from various
parts of the file.

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:23 +05:30
Brian Niebuhr
3b740b10e9 spi: davinci: fix checkpatch errors
Fix the following checkpatch error:

WARNING: unnecessary whitespace before a quoted newline
+       dev_info(&pdev->dev, "Controller at 0x%p \n", davinci_spi->base);

Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
2010-11-18 18:38:23 +05:30
Joe Perches
bc3f67a3e1 drivers/spi: Remove unnecessary semicolons
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-11-14 20:57:20 -07:00
Grant Likely
eae6cb31d8 spi/xilinx: merge OF support code into main driver
Now that the of_platform_bus_type has been merged with the platform
bus type, a single platform driver can handle both OF and non-OF use
cases.  This patch merges the OF support into the platform driver.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
2010-11-09 21:41:28 -07:00
Grant Likely
8fd8821b62 spi/xilinx: fold platform_driver support into main body
This patch merges the platform driver support into the main body of
xilinx_spi.c in preparation for merging the OF and non-OF support
code.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
2010-11-09 21:41:27 -07:00
Grant Likely
91565c4068 spi/xilinx: Eliminate pdata references from common code.
The current code has the OF binding modifying the platform_data
pointer which it must not do, and the common code doesn't really need
to use a pdata pointer.  This patch eliminates the platform_data
references from the common part of the driver in preparation for
merging the OF and non-OF versions.

Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
2010-11-09 21:41:27 -07:00
Uwe Kleine-König
b595076a18 tree-wide: fix comment/printk typos
"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-11-01 15:38:34 -04:00
Linus Torvalds
90ae83f7fc Merge branch 'next-spi' of git://git.secretlab.ca/git/linux-2.6
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6:
  spi/pl022: fix erroneous platform data in U300
  spi: fixed odd static string conventions in core code
  spi/bfin_spi: only request GPIO on first load
  spi/bfin_spi: handle error/status changes after data interrupts
  spi: enable spi_board_info to be registered after spi_master
2010-11-01 07:50:43 -04:00
Linus Torvalds
b18cae4224 Merge branch 'for-next' of git://android.git.kernel.org/kernel/tegra
* 'for-next' of git://android.git.kernel.org/kernel/tegra:
  spi: tegra: fix error setting on timeout
  spi: add spi_tegra driver
  tegra: harmony: enable PCI Express
  tegra: add PCI Express support
  tegra: add PCI Express clocks
  [ARM] tegra: Add APB DMA support
  [ARM] tegra: Add cpufreq support
  [ARM] tegra: common: Update common clock init table
  [ARM] tegra: clock: Add dvfs support, bug fixes, and cleanups
  [ARM] tegra: Add support for reading fuses
  [ARM] tegra: gpio: Add suspend and wake support
  [ARM] tegra: pinmux: add safe values, move tegra2, add suspend
  [ARM] tegra: add suspend and mirror irqs to legacy controller
  [ARM] tegra: Add legacy irq support
  [ARM] tegra: update iomap
2010-10-25 18:42:06 -07:00
Erik Gilling
f41649e040 spi: tegra: fix error setting on timeout
avoids derefencing an uninitialized pointer

Change-Id: Icf528441ae481e9f6f5ddc0be32c7c217fa49701
Signed-off-by: Erik Gilling <konkers@android.com>
2010-10-25 16:57:46 -07:00
Linus Torvalds
092e0e7e52 Merge branch 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
  vfs: make no_llseek the default
  vfs: don't use BKL in default_llseek
  llseek: automatically add .llseek fop
  libfs: use generic_file_llseek for simple_attr
  mac80211: disallow seeks in minstrel debug code
  lirc: make chardev nonseekable
  viotape: use noop_llseek
  raw: use explicit llseek file operations
  ibmasmfs: use generic_file_llseek
  spufs: use llseek in all file operations
  arm/omap: use generic_file_llseek in iommu_debug
  lkdtm: use generic_file_llseek in debugfs
  net/wireless: use generic_file_llseek in debugfs
  drm: use noop_llseek
2010-10-22 10:52:56 -07:00
Linus Walleij
eb288a1f45 spi: fixed odd static string conventions in core code
This patch removes convention of passing a static string as a
parameter to another static string.  The convention is intended to
reduce text usage by sharing the common bits of the string, but the
implementation is inherently fragile (a change to one format string
but not the other will nullify any possible advantage), it isn't
necessarily a net win depending on what this compiler does, and it
it reduces code readability.

Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
[grant.likely@secretlab.ca: removed dev_dbg->dev_err hunk]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-22 09:51:05 -06:00
Michael Hennerich
73e1ac1625 spi/bfin_spi: only request GPIO on first load
The gpiolib code does not allow people to do gpio_request() on a GPIO
once it has already been requested.  So make sure we only request the
pin on the first setup of a SPI device.  Otherwise, if you attempts to
reconfigure a SPI device on the fly (like change bit sizes), the setup
function incorrectly fails.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-22 01:26:46 -06:00
Michael Hennerich
782a895693 spi/bfin_spi: handle error/status changes after data interrupts
The error interrupt on the BF537 SIC cannot be enabled on a
per-peripheral basis.  Once the error interrupt is enabled
for one peripheral, it is automatically enabled for all.

So in the Blackfin on-chip SPI driver, we need to clear out
these known errors in the data interrupt once we've successfully
finished processing all of the pending data.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-22 01:26:46 -06:00
Feng Tang
2b9603a0d7 spi: enable spi_board_info to be registered after spi_master
Currently spi_register_board_info() has to be called before its related
spi_master be registered, otherwise these board info will be just ignored.

This patch will remove this order limit, it adds a global spi master list
like the existing global board info listr. Whenever a board info or a
spi_master is registered, the spi master list or board info list
will be scanned, and a new spi device will be created if there is a
master-board info match.

Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-21 23:52:16 -06:00
Erik Gilling
0c03a1dd5b spi: add spi_tegra driver
v2 changes:
  from Thierry Reding:
    * add "select TEGRA_SYSTEM_DMA" to Kconfig
  from Grant Likely:
    * add oneline description to header
    * inline references to DRIVER_NAME
    * inline references to BUSY_TIMEOUT
    * open coded bytes_per_word()
    * spi_readl/writel -> spi_tegra_readl/writel
    * move transfer validation to spi_tegra_transfer
    * don't request_mem_region iomem as platform bus does that for us
    * __exit -> __devexit

v3 changes:
  from Russell King:
    * put request_mem_region back int
  from Grant Likely:
    * remove #undef DEBUG
    * add SLINK_ to register bit defines
    * remove unused bytes_per_word
    * make spi_tegra_readl/writel static linine
    * various refactoring for clarity
    * mark err if BSY bit is not cleared after 1000 retries
    * move spinlock to protect setting of RDY bit
    * subsys_initcall -> module_init

v3 changes:
  from Grant Likely:
    * update spi_tegra to use PTR_ERRless dma API

v4 changes:
  from Grant Likely:
    * remove empty spi_tegra_cleanup fucntion
    * allow device ids of -1

Signed-off-by: Erik Gilling <konkers@android.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>

spi: tegra: cleanups from upstream review

Change-Id: Icecf7e64efcb39de072a15234ba1faa4bad40d25
Signed-off-by: Erik Gilling <konkers@android.com>
2010-10-21 18:15:05 -07:00
Linus Torvalds
b5153163ed Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
  arm: remove machine_desc.io_pg_offst and .phys_io
  arm: use addruart macro to establish debug mappings
  arm: return both physical and virtual addresses from addruart
  arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
  ARM: make struct machine_desc definition coherent with its comment
  eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
  cpuimx27: fix compile when ULPI is selected
  mach-pcm037_eet: fix compile errors
  Fixing ethernet driver compilation error for i.MX31 ADS board
  cpuimx51: update board support
  mx5: add cpuimx51sd module and its baseboard
  iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
  imx-esdhc: update devices registration
  mx51: add resources for SD/MMC on i.MX51
  iomux-mx51: fix SD1 and SD2's iomux configuration
  clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
  clock-mx51: factorize clk_set_parent and clk_get_rate
  eukrea_mbimxsd: add support for DVI displays
  cpuimx25 & cpuimx35: fix OTG port registration in host mode
  i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
  ...
2010-10-21 16:42:32 -07:00
Ilkka Koskinen
2764c500be spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
In case of TX only with DMA, the driver assumes that the data
has been transferred once DMA callback in invoked. However,
SPI's shift register may still contain data. Thus, the driver
is supposed to verify that the register is empty and the end of
the SPI transfer has been reached.

Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-20 10:43:24 -06:00
Jason Wang
e1993ed642 spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
In the TX_ONLY transfer, the SPI controller also receives data
simultaneously and saves them in the rx register. After the TX_ONLY
transfer, the rx register will hold the random data received during
the last tx transaction.

If the direct following transfer is RX_ONLY, this random data has the
possibility to affect this transfer like this:
  When the SPI controller is changed from TX_ONLY to RX_ONLY,
  the random data makes the rx register full immediately and
  triggers a dummy write automatically(in SPI RX_ONLY transfers,
  we need a dummy write to trigger the first transaction).

  So the first data received in the RX_ONLY transfer will be that
  random data instead of something meaningful.

We can avoid this by inserting a Disable/Re-enable toggle of the
channel after the TX_ONLY transfer, since it purges the rx register.

Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2010-10-20 10:30:53 -06:00
Grant Likely
db181a8ee1 Merge branch 'for-spi' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin into spi/next 2010-10-18 09:25:09 -06:00
Mike Frysinger
9c0a788b43 spi/bfin_spi: namespace local structs
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:44 -04:00
Michael Hennerich
6f7c17f4f9 spi/bfin_spi: init early
Some systems using this bus sometimes have very basic devices on them
such as regulators.  So we need to be loaded even earlier in case the
devices are used by things such as early board init code.  Therefore
register in subsys_initcall().

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:44 -04:00
Bob Liu
2e768659df spi/bfin_spi: check per-transfer bits_per_word
Currently, if the bits_per_word when doing a transfer is not 8bits, we
always treat it as 16bits when we should actually be returning an error.

Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:43 -04:00
Barry Song
4190f6a51f spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
When the hardware is controlling the CS, there are some SPI options
we are unable to support.  So issue a warning in the hopes that the
user will change to a SPI mode where we can support things sanely.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:43 -04:00
Rob Maris
e72dcde72c spi/bfin_spi: cs should be always low when a new transfer begins
Signed-off-by: Rob Maris <maris.rob@vdi.de>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:42 -04:00
Rob Maris
e35954053c spi/bfin_spi: fix typo in comment
Signed-off-by: Rob Maris <maris.rob@vdi.de>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:41 -04:00
Mike Frysinger
7715aad4ef spi/bfin_spi: reject unsupported SPI modes
Who knows what people will try!

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:41 -04:00
Barry Song
a75bd65b21 spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
Using disable_irq() on the IRQ whose handler we are currently executing in
can easily lead to a hang.  So use the nosync variant here.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:40 -04:00
Mike Frysinger
5e8592dca3 spi/bfin_spi: combine duplicate SPI_CTL read/write logic
While combining things, also switch to the proper SPI bit define names.
This lets us punt the rarely used SPI defines.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:39 -04:00
Mike Frysinger
5b47bcd48b spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
During runtime, the spi setup function may be called multiple times on the
same device in order to reconfigure some settings on the fly.  When this
happens, we need to reset the ctl_reg bits so that changing the mode works
as expected.

Reported-by: Andy Getzendanner <james.getzendanner@students.olin.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:39 -04:00
Mike Frysinger
033f44bd0e spi/bfin_spi: push all size checks into the transfer function
This reduces duplication between the setup/transfer functions and keeps
values cached during setup from overriding values changed on a transfer
basis (like bits_per_word).

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:38 -04:00
Yi Li
7370ed6b91 spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
Using disable_irq() on the IRQ whose handler we are currently executing in
can easily lead to a hang.  So use the nosync variant here.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:38 -04:00
Barry Song
9677b0de10 spi/bfin_spi: sync hardware state before reprogramming everything
Sometimes under load, the Blackfin core is able to send SPI register
updates out before the controller is actually disabled.  So when we
go to reprogram the entire state (to switch to a different slave),
make sure we sync after disabling the controller.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:37 -04:00
Barry Song
b052fd0a44 spi/bfin_spi: save/restore state when suspending/resuming
We can't rely on the SPI_CTL/SPI_FLG registers retaining their state when
suspending, so save/restore their entire values.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:37 -04:00
Barry Song
d3cc71f71a spi/bfin_spi: redo GPIO CS handling
The common SPI layers take care of detecting CS conflicts and preventing
two devices from claiming the same CS.  This causes problems for the GPIO
CS support we currently have as we are using CS0 to mean "GPIO CS".  But
if we have multiple devices using a GPIO CS, the common SPI layers see
multiple devices using the virtual "CS0" and reject any such attempts.

To make both work, we introduce an offset define.  This represents the
max number of hardware CS values that the SPI peripheral supports.  If
the CS is below this limit, we know we can use the hardware CS.  If it's
above, we treat it as a GPIO CS.  This keeps the CS unique as seen by
the common code and prevents conflicts.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:36 -04:00
Mike Frysinger
90008a641d spi/bfin_spi: use the SPI namespaced bit names
This lets us push the short SPI MMR bit names out of the global namespace.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:35 -04:00
Mike Frysinger
2a045131db spi/bfin_spi: drop extra memory we don't need
The driver that we based ours on uses a little extra memory behind the
normal driver state, but we don't.  So drop this useless bit of memory.

Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:34 -04:00
Mike Frysinger
b9f139a7a6 spi/bfin_spi: convert struct names to something more logical
The current structure names are a bit confusing as to what they represent,
so use better names.

Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:34 -04:00
Mike Frysinger
9c4542c7a3 spi/bfin_spi: convert read/write/duplex funcs to a dedicated ops structure
Rather than having to look up the same 3 sets of functions at the same
time, just use an ops structure so we only need to set one pointer.

Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:33 -04:00
Mike Frysinger
f4f50c3ff7 spi/bfin_spi: convert queue run state to true/false
No point in creating our own version of true/false defines when there is
already a standard stdbool available to us.

Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:32 -04:00
Mike Frysinger
ab09e0406f spi/bfin_spi: fix up some unused/misleading comments
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:32 -04:00
Mike Frysinger
5cc0159a57 spi/bfin_spi: punt useless null read/write funcs
The chip ops should always be initialized, so having null fallback
functions are useless.

Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:31 -04:00
Mike Frysinger
201bbc6fd8 spi/bfin_spi: drop custom cs_change_per_word support
As David points out, the cs_change_per_word option isn't standard, nor is
anyone actually using it.  So punt all of the dead code considering it
makes up ~10% of the code size.

Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:30 -04:00
Barry Song
8221610e99 spi/bfin_spi: fix CS handling
The CS helper functions were toggling both the Flag Enable and the Flag
Value bits, but the Flag Value bit is ignored if the corresponding Flag
Enable bit is cleared.  So under high speed transactions, the CS sometimes
would not toggle properly.

Since it makes no sense to toggle the Flag Enable bit dynamically when we
actually want to control the Flag Value, do this when setting up the device
and then only handle toggling of the CS value during runtime.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:30 -04:00
Yi Li
f6a6d96685 spi/bfin_spi: utilize the SPI interrupt in PIO mode
The current behavior in PIO mode is to poll the SPI status registers which
can obviously lead to higher latencies when doing a lot of SPI traffic.
There is a SPI interrupt which can be used instead to signal individual
completion of transactions.

Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:29 -04:00