Logitec LAN-GTJ U2A (http://www.pro.logitec.co.jp/pro/g/gLAN-GTJU2A/)
USB 2.0 10/10/1000 Ethernet adapter is based on ASIX AX88178 chipset.
This patch adds missing USB ID for the device.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boot code drivers dont have cleanup routine, so pci function
remains in unknown state prior to driver load. So during driver load
issue FLR unconditionally.
Update driver version to 5.0.14.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OCM window register offset was calculated incorrectly for
pci function greater than zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When interface is down, create temporary context to config LED.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My conversion of tehuti to use request_firmware() was confused about
the filename of the firmware blob. Change the driver to match the
blob.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent ifb changes, we must use lockless __skb_dequeue() since
lock is not anymore initialized.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jamal Hadi Salim <hadi@cyberus.ca>
Cc: Changli Gao <xiaosuo@gmail.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are using skb_transport_offset(skb) instead of skb->csum_start
for NETIF_F_HW_CSUM offload. This does not matter now, but if someone
implements checksumming of encapsulated packets then this will break silently.
TSO output paths are left as they are, since they are for IP+TCP only
(might be worth converting though).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace skb->csum_start - skb_headroom(skb) with skb_checksum_start_offset().
Note for usb/smsc95xx: skb->data - skb->head == skb_headroom(skb).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't change ip_summed from CHECKSUM_PARTIAL to CHECKSUM_NONE
or CHECKSUM_UNNECESSARY because checksum in packet's headers is
not valid and will cause invalid checksum when frame is forwarded.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the mbox polling uses the schedule_timeout, the mbox_lock should be
a mutex and not a spin lock.
The commit f25b03a replaced udelay() with schedule_timeout() but didn't
change mbox_lock to semaphore or mutex.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provices the debugfs interface to see RLB hash table
like the following:
# cat /sys/kernel/debug/bonding/bond0/rlb_hash_table
SourceIP DestinationIP Destination MAC DEV
10.124.196.205 10.124.196.205 ff:ff:ff:ff:ff:ff eth4
10.124.196.205 10.124.196.81 00:19:99:XX:XX:XX eth3
10.124.196.205 10.124.196.1 00:21:d8:XX:XX:XX eth0
This is helpful to check if the receive load balancing works as expected.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply migrates some macros from bond_alb.c to bond_alb.h.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate Tx queue memory on the node indicated by the new
netdev_queue_numa_node_read.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code parses the VPD RO section for keywords but makes static
assumptions about the location of the section. Remove them and parse
the VPD to find it.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch originally from Joe Perches, unmodified.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver keeps a bitmap of the netdevs it registered so it knows what to
unregister later. Remove that and look at reg_state instead.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a field the driver uses to keep track of the name of the first
netdev it manages to register. Do this by changing the registration
loop to stop the first time it fails so the first registered device is
trivial to tell.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last byte of the buffer for MSI-X names could not be used due to a
bogus -1. Also do not explicitly clear the last byte, snprintf will do
the right thing.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently MSI-X names for netdevs with long names are truncated in
/proc/interrupts due to insufficient space. Use IFNAMSIZ to size the
needed space.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print information about each port when its netdev is registered instead
of looping separately over the ports at the end. The bulk of this patch
is due to indentation change.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And fix the supported flags ethtool reports for the two cases.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of queues is known early, move the calls to
netif_set_real_num_[rt]x_queues before register_netdev.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to read the clock frequency from VPD, we already get it a bit
later from FW, after any potential adjustments.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable relaxed ordering for descriptor reads and packet I/O.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Includes FCoE releated fixes in FW flows
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding DCB initialization and handling on 57712 FW/HW
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This callback required to allow FCoE traffic to be
sent on separate priority queue from other L2 traffic,
which is managed by PFC in HW.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Includes new driver structures and FW/HW configuration for FCoE ring
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Shmulik Ravid-Rabinovitz <shmulikr@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_na_send() attempts to insert a VLAN tag in between building and
sending packets of the respective formats. If the slave does not
implement hardware VLAN tag insertion then vlan_put_tag() will mangle
the network-layer header because the Ethernet header is not present at
this point (unlike in bond_arp_send()).
Fix this by adding the tag out-of-line and relying on
dev_hard_start_xmit() to insert it inline if necessary.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_change_active_slave() may be called when a slave is added, even
if the bond has not been brought up yet. It may then attempt to send
packets, and further it may use mcast_work which is uninitialised
before the bond is brought up. Add the necessary checks for
netif_running(bond->dev).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bond may have a mixture of slave devices with and without hardware
VLAN tag insertion capability. Therefore it always claims this
capability and performs software VLAN tag insertion if the slave does
not.
Since commit 7b9c609037, this has
also been done by dev_hard_start_xmit(). The result is that VLAN-
tagged skbs are now double-tagged when transmitted through slave
devices without hardware VLAN tag insertion!
Remove the now-redundant logic from bond_dev_queue_xmit().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
axnet_cs:
Accton EN2328 or compatible (id: 0x01bf, 0x2328) uses Asix chip.
So it works better with axnet_cs instead of pcnet_cs.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
The returned slave is incorrect, if the net device under check is not
charged yet by the master.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old survey implementation was broken and returned nonsense data.
Clear cycle counters and survey data on reset. Since the cycle counters easily
overflow it's better to keep a local version of collected survey data (in ms
resolution, instead of clockrate) and update this every time survey is
retrieved. If survey is retrieved often enough to avoid cycle counter overflows
this works fine, otherwise we could update survey more often, like ath9k does.
Still only the survey for the current channel is kept.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After merge of the rtl8192ce driver, a powerpc build fails with:
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c: In function 'rtl92c_init_sw_vars':
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:76: error: implicit declaration of function 'vmalloc'
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:76: warning: cast to pointer from integer of different size
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c: In function 'rtl92c_deinit_sw_vars':
drivers/net/wireless/rtlwifi/rtl8192ce/rtl8192c-sw.c:91: error: implicit declaration of function 'vfree'
The problem is fixed by explicitly including the appropriate header.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Target Tx power available in eeprom is for PAPRD. If PAPRD
fails, paprd scale factor needs to be detected from this
target tx power.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the drop in Tx power for a particular mcs rate exceeds
the paprd scale factor, paprd may not work properly. Disable
paprd for any such rates.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add multiple Tx IQ cal support to improve EVM accross
different power levels.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helper can be used in multiple places. Also make
it inline returning u8.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
While compiling linux-next (next-20101216) I fell over this breakage:
...
drivers/net/wireless/iwlwifi/iwl-agn-rs.c: In function ‘iwl_rs_rate_init’:
drivers/net/wireless/iwlwifi/iwl-agn-rs.c:2876:8: error: ‘struct iwl_lq_sta’ has no member named ‘dbg_fixed_rate’
dbg_fixed_rate is only used when CONFIG_MAC80211_DEBUGFS is set:
[ drivers/net/wireless/iwlwifi/iwl-agn-rs.h ]
...
#ifdef CONFIG_MAC80211_DEBUGFS
struct dentry *rs_sta_dbgfs_scale_table_file;
struct dentry *rs_sta_dbgfs_stats_table_file;
struct dentry *rs_sta_dbgfs_rate_scale_data_file;
struct dentry *rs_sta_dbgfs_tx_agg_tid_en_file;
u32 dbg_fixed_rate;
#endif
The issue was introduced by commit a1da077bc36368eb7d6312e7e49260f0a3d92c77:
"iwlwifi: clear dbg_fixed_rate during init"
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
PM-QOS value can be user specified via module parameter.
This patch adds few comments regarding this in the driver
code.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not required for USB devices.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow drivers or rate control algorithms to specify BlockAck session
timeout when initiating an ADDBA transaction. This is useful in cases
where maintaining persistent BA sessions does not incur any overhead.
The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc
drivers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
patch "iwlagn: check ready in iwlagn_bss_info_changed()" introduce
whitespace, fix it
please merge with the previous patch
Reported by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows the pm-qos value to be user configurable by making it as
a module parameter.This will help our customers to configure the pm-qos
value according to the effect in throughput due to the DMA latency problem
which was observed in Intel Pinetrail platforms.
The tested value of '55' will be filled as the default
pm-qos-value incase the user does not specifies pm-qos value as a
module parameter.
example usage: sudo modprobe ath9k pmqos=65
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Without this, gcc 4.5 won't compile xen-netfront and xen-blkfront, where
this is being used to specify array sizes.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: David Miller <davem@davemloft.net>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change some file names and Kconfig settings so that this new module matches
the new way of using wl12xx instead of wl1271.
Also fix SDIO power enabling and disabling to match the latest way of doing
it.
Cc: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
With the current single-queue implementation traffic priorization is not
working correctly - when using multiple BE streams and one, say VI stream,
the VI stream will share bandwidth almost equally with the BE streams.
To fix the issue, implement per AC queues, which are emptied in priority
order to the firmware. To keep it relatively simple, maintain a global
buffer count and global queue stop/wake instead of per-AC.
With these changes, priorization appears to work just fine.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Currently, the debug level is set in compilation time (by the DEBUG_LEVEL
const). This method has the advantage of compiling only the relevant
messages, while optimizing out the unused ones.
In order to allow runtime control over the debug_level, while optimizing
out messages when debug messages are not needed, we combine some methods:
1. use dynamic_debug (pr_debug) rather then printk.
2. add debug_level module param in order to set debug level during insmod.
3. add debug_level sysfs file in order to allow dynamic control over the
debug level.
Since patches for pr_debug_hex_dump() implementation haven't been applied yet,
we are still temporarly using print_hex_dump().
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Inclusion of a WPS IE in probe requests caused a problem
in the driver due to the maximum size of the probe request
template and the max_scan_ie_len values at initialization.
Increased the size of probe request template
to the maximum size allowed by the firmware.
Struct wl12xx_probe_req_template, which was only used
for calculating the max size of the probe request template,
is no longer used and needed.
max_scan_ie_len is used for validating the size of
additional IEs in scan requests.
Initialized the max_scan_ie_len field to the maximum size
of the probe request template minus the ieee80211 header size.
Signed-off-by: Guy Eilam <guy@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The auto-arp feature of wl12xx allows the firmware to automatically
response to arp requests asking for its ip.
in order to use it, we configure the arp response template and
enable the corresponding bit in wl1271_acx_arp_filter (along with
passing its ip)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This module enables individually generating RX and TX traffic
over the SDIO bus on which the WL1271 chipset is connected.
This is required to perform RF interference testing.
The module takes 2 module parameters 'rx' and 'tx'.
To generate RX traffic:
modprobe wl1271_sdio_test rx=1
To generate TX traffic:
modprobe wl1271_sdio_test tx=1
To generate both RX & TX traffic, set both rx and tx to 1.
You can change the testing configuration at runtime by changing
the rx & tx values at /sys/modules/wl1271_sdio_test/
To stop testing simply unload the module.
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Reviewed-by: Carlos Chinea <carlos.chinea@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Disabling the 11a channels when not supported in the reg_notify function was
not working as it should, because when the driver is initiailizing (and
registering itself with mac80211), it would get the reg notification too
early. At that point the driver wouldn't have received the NVS yet, so it
wouldn't know whether 11a was supported.
To fix this, we disable 11a channels when we read the NVS instead. Also, it
is easier (and still safe) to set n_channels to zero instead of setting the
disabled flag on every 11a channel.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago. Convert all the
in-kernel users. The conversions are completely equivalent and
trivial.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits)
pppoe.c: Fix kernel panic caused by __pppoe_xmit
WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers.
bnx2x: Advance a version number to 1.60.01-0
bnx2x: Fixed a compilation warning
bnx2x: LSO code was broken on BE platforms
qlge: Fix deadlock when cancelling worker.
net: fix skb_defer_rx_timestamp()
cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes
phy: add the IC+ IP1001 driver
atm: correct sysfs 'device' link creation and parent relationships
MAINTAINERS: remove me from tulip
SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address
enic: Bug Fix: Pass napi reference to the isr that services receive queue
ipv6: fix nl group when advertising a new link
connector: add module alias
net: Document the kernel_recvmsg() function
r8169: Fix runtime power management
hso: IP checksuming doesn't work on GE0301 option cards
xfrm: Fix xfrm_state_migrate leak
net: Convert netpoll blocking api in bonding driver to be a counter
...
This USB ID is for the WUBI-100GW 802.11g Wireless LAN USB Device that
uses p54usb.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Eduardo Costa <ecosta.tmp@gmail.com>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Multiple devices use almost the same .cfg with minor differences.
Use macro and remove the duplication. By doing this, reduce
the chance for mistake while modify .cfg parameters
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For WiFi/WiMAX combo devices, if WiMAX own the RF, WiFi driver
try to access RF and fail. This is the W/A to To avoid WiFi keep
reloading firmware and try to access RF again.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For logging EEPROM related info, instead of using IWL_DEBUG_INFO,
use the dedicated logging (IWL_DEBUG_EEPROM) for easier debugging
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This removes the old TX power reading code, it isn't
necessary since the new code is able to read all the
various EEPROM layouts due to relying on information
contained in the EEPROM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
For the new 1x1 devices, hw and uCode will support rx
antenna diversity, but we need to indicate 1x1 device to
AccessPoint to make sure it won't use MIMO.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
The compiler correctly warns:
iwl-agn-tx.c: In function ‘iwlagn_tx_status_reply_compressed_ba’:
iwl-agn-tx.c:1240: warning: ‘bitmap’ may be used uninitialized in this function
Move the debug print to the branch that reads the
bitmap, and move the variables too so it's more
obvious where they are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
In function iwlagn_bss_info_changed(), we need to check if the driver
is ready before doing real work. Also, the previously put WARN() is
removed because the vif is not guaranteed to be valid. uCode restart
routine will clear the vif.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
This prevent bad fixed_rate keeps crashing uCode in an endless loop.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Since this driver is implemented as NAPI,
netif_receive_skb must be used not netif_rx.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add setting TEC/REC statistics processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For reduce "if" condition, easy to read/understand the code,
optimize "if" condition in rx/tx processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case this driver is integrated as module, and when this
module is re-installed, no interrupts is to be occurred.
For the above issue, move MSI processing to open/release processing.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify miss-setting status issue at suspend.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify like use calculated value directly passed by CAN core module.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding rule violation.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For easy to readable, use netdev_dbg instead of dev_dbg partly
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, Copyright and module description are not formal.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For improve tx/rx speed, reduce register access.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, these two functions spec(returned value) is unnatural.
Thus, change the return value's spec
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For easy to read/understand, Rename function/macro name.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, in case CONFIG_PM is disabled, compiler outputs warnings.
Move six functions which are used only CONFIG_PM is enabled,
into "#ifdef CONFIG_PM" area.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace complex "goto" to "do~while".
For easy to read/understand, it divides a rx function into some functions.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
there is endianness issue both Tx and Rx.
Currently, data is set like below.
Register:
MSB--LSB
x x D0 D1
x x D2 D3
x x D4 D5
x x D6 D7
But Data to be sent must be set like below.
Register:
MSB--LSB
x x D1 D0
x x D3 D2
x x D5 D4
x x D7 D6 (x means reserved area.)
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To easy to read/understand, divide poll function into two sub-functions.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is no flow control processing.
Thus, Add flow control processing as
when there is no empty of tx buffer,
netif_stop_queue is called.
When there is empty buffer, netif_wake_queue is called.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6175ddf06b changes the way
memcpy_toio() works for x86_64, causing firmware loading to fail for
some Ralink WLAN devices with the rt2800pci driver since linux 2.6.34.
This causes the log message: "phy0 -> rt2800pci_load_firmware: Error -
PBF system register not ready.".
Fix this by using __iowrite32_copy instead of memcpy_toio().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pad beacon to a multiple of 32 bits in preparation for the change
from memcpy_toio() to __iowrite32_copy() in register_multiwrite().
Signed-off-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stray semicolon after DEBUG_PRINTK_MSG causes things
like "if (...) WARNING(...); else {}" to fail with syntax error.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Queue names were incorrectly copied from the legacy drivers,
as a result the queue names were inversed to what was expected.
This renames the queues using this mapping:
QID_AC_BK -> QID_AC_VO (priority 0)
QID_AC_BE -> QID_AC_VI (priority 1)
QID_AC_VI -> QID_AC_BE (priority 2)
QID_AC_VO -> QID_AC_BK (priority 3)
Note that this was a naming problem only, which didn't affect
the assignment of frames to their respective queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a queue entry flag ENTRY_DATA_STATUS_PENDING,
which can be used to indicate a queue entry has
returned from the hardware and is waiting for
status processing. Using this flag we can add
some extra sanity checks to prevent queue corruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the rt2x00_dmastart function to rt2x00lib which
marks the queue_entry as "owned by device", and increased
the Q_INDEX number.
This cleanups up the index handling by rt2x00lib which
at until so far used hackish approaches to keep the
RX queue index numbering sane.
The rt2x00pci.c changes are from Helmut Schaa
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a new command to the queue handlers: "flush",
this moves the flush() callback from mac80211
into rt2x00queue and adds support for flushing
the RX queue as well.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add wrapper functions in rt2x00queue.c to
start & stop queues. This control must be protected
using a mutex.
Queues can also be paused which will halt the flow
of packets between the driver and mac80211. This doesn't
require a mutex protection.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, change the queue callback
function names to have 3 different actions: start, kick & stop.
We can now also remove the STATE_RADIO_RX_ON/STATE_RADIO_RX_OFF
device_state flags, and replace the usage with using the
start_queue/stop_queue callback functions.
This streamlines the RX queue handling to the
similar approach as all other queues.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the queue refactoring, we now introduce
3 queue commands: start, kick, stop.
- Start: will enable a queue, for TX this will
not mean anything, while for beacons and RX
this will update the registers to enable the queue.
- Kick: This will kick all pending frames to
the hardware. This is needed for the TX queue
to push all frames to the HW after the queue
has been started
- Stop: This will stop the queue in the hardware,
and cancel any pending work (So this doesn't
mean the queue is empty after a stop!).
Move all code from the drivers into the appropriate
functions, and link those calls to the old rt2x00lib
callback functions (we will fix this later when we
refactor the queue control inside rt2x00lib).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 0204464329 "Check for specific changed
flags when updating the erp config" changed the way in which a new beacon
interval gets handled. However, due to a bug in rt2800usb and rt2800pci the
beacon interval was reset during each scan, thus causing problems in AdHoc
mode.
Fix this by not cleaning up the beacon interval when killing the beacon queue
but just prevent the device from sending out beacons.
Reported-by: Wolfgang Kufner <wolfgang.kufner@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent changes to the TX-done code of rt2x00 resulted in TX-ed frames not
being returned to mac80211 in the original state, and therefore with
insufficient headroom for re-transmissions.
Fix this by reverting the changes done and by ensuring we remove the inserted
L2pad by moving the header backwards instead of the data forwards.
At the same time also make sure that the rt2x00queue_remove_l2pad will not
move any memory when a frame has no data at all.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Jay Hung <Jay_Hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an rt2x00 USB device is unplugged while in use, it reliably
hangs the whole system. After some time the watchdog prints:
BUG: soft lockup - CPU#0 stuck for 64s! [kworker/u:0:5]
...
[<c01a88d8>] (usb_submit_urb+0x0/0x2ac) from [<bf0e752c>] (rt2x00usb_kick_rx_entry+0xb4/0xe8 [rt2x00usb])
[<bf0e7478>] (rt2x00usb_kick_rx_entry+0x0/0xe8 [rt2x00usb]) from [<bf0e7588>] (rt2x00usb_clear_entry+x28/0x2c [rt2x00usb])
[<bf0e7560>] (rt2x00usb_clear_entry+0x0/0x2c [rt2x00usb]) from [<bf0d5bc4>] (rt2x00lib_rxdone+0x2e0/0x2f8 [rt2x00lib])
[<bf0d58e4>] (rt2x00lib_rxdone+0x0/0x2f8 [rt2x00lib]) from [<bf0e7e00>] (rt2x00usb_work_rxdone+0x54/0x74 [rt2x00usb])
[<bf0e7dac>] (rt2x00usb_work_rxdone+0x0/0x74 [rt2x00usb]) from [<c00542b4>] (process_one_work+0x20c/0x35c)
Clear the DEVICE_STATE_PRESENT flag when usb_submit_urb()
returns -ENODEV to fix this.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add RF chip definition
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement the get_survey callback to allow user space to read statistics
about the current channel condition.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add and modify NIC Configuration and LED definition of EEPROM
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduces the likelihood of false pulse detects in the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM contains scale factors for the tx power, which define
the range of allowable difference between target power and training
power. If the difference is too big, PA predistortion cannot be used.
For 2.4 GHz there is only one scale factor, for 5 GHz there are
three, depending on the specific frequency range.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The EEPROM PAPRD rate mask fields only contain mask values for actual
rates in the low 25 bits. The upper bits are reserved for tx power
scale values. Add the proper mask definitions and use them before
writing the values to the register.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to measure the thermal values correctly for PAPRD, we need
to send training frames before setting up the gain table for the measurement,
and then again afterwards for the actual training.
For further improvement, send training frames at MCS0 instead of 54 MBit/s
legacy. That way we can use the No-ACK flag for the transmission, which
speeds up PAPRD training in general, as the hardware won't have to
retransmit and wait for ACK timeout (was previously set to 4 * 6
transmission attempts).
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testing shows that adjusting the slot time based on the coverage class
produces very high latencies and very low throughput on long distance links.
Adjusting only the ACK timeout and leaving the slot time at the regular
values - while technically not optimal for CSMA - works a lot better on
long links (tested with 10 km distance)
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(u32) -1 is not particularly useful as a slottime default, so even though
the ath9k_hw default should never get used, it's better to pick something
sane here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to have separate callbacks for pre-AR9003 vs AR9003
SREV version checks, so just merge those into one function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9280 based hardware with 3 antennas and slow antenna diversity has
not been seen in the wild and ath9k does not support that form of
antenna diversity, so remove the EEPROM ops for it.
These EEPROM ops are currently only used for setting the
AR_PHY_SWITCH_COM register, which is being done in the EEPROM specific
file already.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also add a comment about a potential array overrun that needs to
be reviewed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer chips do not need this, and maybe these register writes could have
negative side effects on newer hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wireless-testing commit 04caf86375
('ath9k: more tx setup cleanups') merged tx path code for HT vs
non-HT frames, however it did not pass the tid pointer to
ath_tx_send_normal, causing an inconsistency between AMPDU vs
non-AMPDU sequence number handling.
Fix this by always passing in the tid pointer for all QoS data frames.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW has to be awake when accessing registers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As discussed we do not know band width at core reset time and it is not a good
idea to reset whole just to change band. So just set unconditionally 20 MHz
band width as default during core reset.
As for defines PHY clock changed to band width in specs and it makes much more
sens to call defines by band width which is self-explainable. Updated specs do
not mention 0 value, but comparing to old ones you can notice lineral relation
between PHY clock speed and band width. So it makes sense for 0x0 value to be
10 MHz band width.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow userspace to specify that a given key
is default only for unicast and/or multicast
transmissions. Only WEP keys are for both,
WPA/RSN keys set here are GTKs for multicast
only. For more future flexibility, allow to
specify all combiations.
Wireless extensions can only set both so use
nl80211; WEP keys (connect keys) must be set
as default for both (but 802.1X WEP is still
possible).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers TBTT_TIMER ,DMA_BEACON_ALERT ,NEXT_SWBA are need to be
configured only for AP and IBSS mode.
SWBA register is used for generating software interrupts so that beacon
frames will be created by the software.DMA beacon alert register is
to indicate the hardware to DMA the contents of beacon buffer to PCU buffer
and TBTT to start transmitting the packet buffer to the base band.
Clearly these things are not needed for station/monitor mode so
remove configuring them.
Cc: doug dahlby <ddahlby@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
key4 of micentry is used, if ATH_CRYPT_CAP_MIC_COMBINED is set.
But is not cleared on key cache reset.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to change interface type
without bringing down the interface.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 will notify drivers when to go idle and ath9k
assumed that it would get further notifications for idle
states after a device stop() config call but as per agreed
semantics the idle state of the radio is left up to driver
after mac80211 issues the stop() callback. The driver is
resposnbile for ensuring the device remains idle after
that even between suspend / resume calls.
This fixes suspend/resume when you issue suspend and resume
twice on ath9k when ath9k_stop() was already called. We need
to put the radio to full sleep in order for resume to work
correctly.
What might seem fishy is we are turning the radio off
after resume. The reason why we do this is because we know
we should not have anything enabled after a mac80211 tells
us to stop(), if we resume and never get a start() we won't
get another stop() by mac80211 so to be safe always bring
the 802.11 device with the radio disabled after resume,
this ensures that if we suspend we already have the radio
disabled and only a start() will ever trigger it on.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon a failure we never call ath9k_ps_restore() on ath_radio_enable(),
this will throw off the sc->ps_usecount. When the sc->ps_usecount
is > 0 we never put the chip to full sleep. This drains battery,
and will also make the chip fail upon resume with:
ath: Starting driver with initial channel: 5745 MHz
ath: timeout (100000 us) on reg 0x7000: 0xdeadbeef & 0x00000003 != 0x00000000
This would make the chip useless upon resume.
I cannot prove this can happen but in theory it is so best to
avoid this race completely and not have users complain about
a broken device after resume.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The code wants to check if there's a channel and it is not disabled,
but it used to check if channel is not NULL and accessed the channel
struct if this check failed.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ehea_error, ehea_info and ehea_debug macros.
Use pr_fmt, pr_<level>, netdev_<level> and netif_<level> as appropriate.
Fix messages to use trailing "\n", some messages had an extra one
as the old ehea_<level> macros added a trailing "\n".
Coalesced long format strings.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
__pppoe_xmit function return value was invalid resulting in
additional call to kfree_skb on already freed skb. This resulted in
memory corruption and consequent kernel panic after PPPoE peer
terminated the link.
This fixes commit 55c95e738d.
Reported-by: Gorik Van Steenberge <gvs@zemos.net>
Reported-by: Daniel Kenzelmann <kernel.bugzilla@kenzelmann.dyndns.info>
Reported-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Reported-by: Pawel Staszewski <pstaszewski@artcom.pl>
Diagnosed-by: Andrej Ota <andrej@ota.si>
Diagnosed-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Denys Fedoryshchenko <nuclearcat@nuclearcat.com>
Tested-by: Pawel Staszewski <pstaszewski@artcom.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Andrej Ota <andrej@ota.si>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must not wake the TX queue without free TX descriptors.
sca_xmit() expects at least one free descriptor and BUGs otherwise.
Problem reported and fix tested by Bernie Innocenti and Ward Vandewege.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_src_init_t2() is used only when BCM_CNIC is defined.
So, to avoid a compilation warning, we won't define it unless
BCM_CNIC is defined.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the LSO code work on BE platforms: parsing_data field of
a parsing BD (PBD) for 57712 was improperly composed which made FW read wrong
values for TCP header's length and offset and, as a result, the corresponding
PCI device was performing bad DMA reads triggering EEH.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing usage of rtnl_lock() to protect firmware interface registers.
These registers are accessed in some worker threads and can create a
deadlock if rtnl_lock is taken by upper layers while the worker is still
pending.
We remove rtnl_lock and use a driver mutex just while mailboxes are
accessed.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flush_scheduled_work() is on its way out. Drop flush_scheduled_work()
from prism2_free_local_data() and replace it with explicit flushing of
work items on the respective free functions. Work items in ap_data
are flushed from hostap_free_data() and the ones in local_info from
prism2_free_local_data().
Flush is used instead of cancel as some process and free items from
queue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jes Sorensen <jes@trained-monkey.org>
Cc: netdev@vger.kernel.org
i2400m implements dynamic work allocation and queueing mechanism in
i2400_schedule_work(); however, this is only used for reset and
recovery which can be served equally well with preallocated per device
works.
Replace i2400m_schedule_work() with two work structs in struct i2400m.
These works are explicitly canceled when the device is released making
calls to flush_scheduled_work(), which is being deprecated,
unnecessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Cc: linux-wimax@intel.com
Cc: netdev@vger.kernel.org
gp->reset_task_pending is always set right before reset_task is
scheduled and as there is no synchronization between the setting and
scheduling, busy looping on reset_task_pending before flushing
reset_task doesn't really buy anything.
Directly flush gp->reset_task on suspend and cancel on detach.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
All three drivers use flush_scheduled_work() similarly during driver
detach. Replace it with explicit cancels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
flush_scheduled_work() is on its way out. Remove its usage from
iseries_veth.
* Cancelling a delayed work, queueing it for immediate execution if
cancelled and then waiting for completion can be done by simply
calling flush_delayed_work_sync().
* Explicitly cancel cnx->statemachine_wq on module unload.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Santiago Leon <santil@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
Directly cancel port->reset_task from ehea_shutdown_single_port()
instead. As this cancels the work for each port on driver detach,
flushing system_wq from ehea_remove() or ehea_module_exit() is no
longer necessary.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
ehea_rereg_mr_task is not used. Remove it and drop @work parameter
from ehea_rereg_mrs().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Breno Leitao <leitao@linux.vnet.ibm.com>
Cc: netdev@vger.kernel.org
flush_scheduled_work() is on its way out. This patch contains simple
conversions to replace flush_scheduled_work() usage with direct
cancels and flushes.
Directly cancel the used works on driver detach and flush them in
other cases.
The conversions are mostly straight forward and the only dangers are,
* Forgetting to cancel/flush one or more used works.
* Cancelling when a work should be flushed (ie. the work must be
executed once scheduled whether the driver is detaching or not).
I've gone over the changes multiple times but it would be much
appreciated if you can review with the above points in mind.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: e1000-devel@lists.sourceforge.net
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: netdev@vger.kernel.org
janz-ican3, sh_eth, skge and vxge don't use workqueue at all and there
is no reason to flush the system_wq. Drop flush_scheduled_work()
calls and references to workqueue.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Ramkrishna Vepa <ramkrishna.vepa@exar.com>
Cc: Sivakumar Subramani <sivakumar.subramani@exar.com>
Cc: Sreenivasa Honnur <sreenivasa.honnur@exar.com>
Cc: Jon Mason <jon.mason@exar.com>
Cc: netdev@vger.kernel.org
The driver global au_macs[] is unused in the entire kernel tree,
so remove it.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
text data bss dec hex filename
109387 389 24432 134208 20c40 drivers/net/s2io.o.old
109358 389 24432 134179 20c23 drivers/net/s2io.o.new
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put immutable data in read/only section.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
modparm rx_ring_sz can be set to be greater than the maximum allowable
number of blocks. This results in an array overrun when probing the
driver, and causes memory corruption.
Also, the MAX_RX_DESC_1 multiply the max number of rings by max number
of blocker per ring by 127, but the driver does the same calculation
with 127+1. This results in the possibility of the value being set
being larger than the maximum allowable value.
Finally, clean-up the s2io_ethtool_gringparam code to be more
intuitive.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New adapters will have part numbers stored in string format rather than
simple hex format. This function will read part number formats in either
hex or string.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Adding this default case resolves the issue.
v2- Removed "break" in default case based on feedback
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct error messages when setting up Rx resources and when checking
module parameters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tx_desc can be dereferenced as a null pointer when count is passed in
as 0.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide support to e1000e for displaying the new format of the PBA found
in the EEPROM. The unique PBA identifier is no longer restricted to
hexadecimal numbers and must now be read and displayed as a string.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During init, reading the 2 PHY ID registers back-to-back in the default
fast mode could return invalid data (all F's) and in slow mode could
return data to the second read the data from the first read. To resolve
the issue in fast mode, set to slow mode before any PHY accesses; to
resolve the issue in slow mode, put in a delay for every 82579 PHY access.
Since this PHY is currently only paired with the pch2lan MAC and the PHY
type is not known before the first PHY access which can fail this way,
check for this based on MAC-type.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The LPLU (Low Power Link Up) and Gigabit Disable bits (a.k.a. OEM bits)
were being configured incorrectly when device goes to D3 state.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When link partner is sending continuous Config symbols, the 82571 Serdes
FIFO can overflow resulting in Invalid bit getting set. To resolve this,
if Sync and Config bits are both 1 ignore the Invalid bit and restart
auto-negotiation.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The workaround function e1000_configure_k1_pchlan() assumes the h/w
semaphore is already acquired. This was originally missed when setting up
the part for the ethtool loopback test.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Increasing the transmit fifo by 4K (by decreasing the receive fifo size
specified in .pba by the same amount) increases Tx performance.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On certain 82571-based mezzanine NICs in some blade servers, the ethtool
link test can fail due to the serdes_has_link flag not set correctly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The kernel goes BUG() at the time 'ethtool -p eth0 3' comes
back, which is due to adapter->led_blink_task initialized
several times. At the time it is still running this results
in a corrupted task_list of the associated workqueue.
The fix is to move the workqueue initialization to the
probe function instead.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some minor cleanup to use string calls that use bound checks just to
be extra safe.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit f62bbb5e62
ixgbe: Update ixgbe to use new vlan accleration.
removed ETH_FLAG_NTUPLE from the supported flags.
This patch puts it back on to allow for setting ntuple via ethtool.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables X540 hardware to use it's own set of support
functions. This is useful as it has no need of SFP+ support. A
couple minor bugs with the eeprom semaphore were also cleaned up.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The existing PHY ID for X540 was from early production hardware and
is no longer correct. This patch corrects that.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on a patch from Jesse Gross.
Enable vlan tag insertion even when vlan group is not configured.
For ixgb HW both CTRL0.VME and VLE bit in the Tx descriptor need to be set
in order to enable HW acceleration.
Introduced separate functions for enabling/disabling of vlan tag stripping
similar to ixgbe.
CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on work by Joe Perches <joe@perches.com>
Using static const to decrease data and overall object size.
CC: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Dean noticed that 'err' wasn't being set when the "goto err_dma"
statement is executed in the following hunk from the commit. It's value
will be zero as a result of a successful call to e1000_init_hw_struct().
This patch changes the error condition to be correctly propagated.
CC: stable@kernel.org
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch provides the debugfs facility to the bonding driver.
The "bonding" directory is created in the debugfs root and directories of
each bonding interface (like bond0, bond1...) are created in that.
# mount -t debugfs none /sys/kernel/debug
# ls /sys/kernel/debug/bonding
bond0 bond1
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update vxge driver version to 2.5.1
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure the workload clock register and TIM register for independent
interrupt moderation based on the individual vpath utilization instead
of common link utilization. This greatly improves latency.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hot-unplugging a vxge adapter while running, the driver's remove
routine prints warning and then stalls the calling thread. This is due
to vxge_remove calling vxge_device_unregister to unregister the netdev
before calling flush_scheduled_work clear any pending work. Swapping
the order of these two functions resolves the issue.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a workqueue to handle the device reset during a transmit timeout, as
there can be a deadlock during bringup. Also, set the netif carrier off
before the watchdog reset is started to prevent the timeout from
reoccurring while still processing the first.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only BAR0 is ever accessed, thus making the calls to pci_request_regions
overkill. Change calls of pci_request_regions to pci_request_region to
reduce the size of the mapped area.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling pci_disable_sriov when unloading a SR-IOV physical function
driver from a host when a guest is using a virtual function from that
device can cause a host crash or VM crash. The crash is caused by the
virtual config space no longer being present when PF is removed (due to
the pci_disable_sriov). This can be avoided by not calling
pci_disable_sriov to disable the PCI space when shutting down the PF.
Each function in the X3100 operates independently and in this case will
operate properly in the absence of the PF.
Also, added improved logic in the detection of SR-IOV initialization.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move function locations to remove the need for internal declarations and
other misc clean-ups.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: Arpit Patel <arpit.patel@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various drivers are using implementations of ethtool_ops::get_link
that are equivalent to the default ethtool_op_get_link(). Change
them to use that instead.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Was using L1_CACHE_BYTES for the Ingress Queue Entry Size but it really
needs to be 64 bytes in order to support the largest message sizes.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the IC+ IP1001 (Gigabit Ethernet Transceiver) driver.
I've had to add an additional delay (2ns) to adjust RX clock phase at
GMII/ RGMII interface (according to the PHY data-sheet). This helps to
have the RGMII working on some ST platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support in enic 802.1Qbh port profile provisioning code
to use the mac address set by IFLA_VF_MAC. For now we handle this mac as a
special case for a VM mac address sent to us by libvirt. The VM mac address
is sent to the switch along with the rest of the port profile provisioning
data. This patch also adds calls to register and deregister the mac address
during port profile association/deassociation.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the ndo_set_vf_mac netdev operation for enic
dynamic devices. It treats the mac address set by IFLA_VF_MAC as a
special case to use it in the port profile provisioning data.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_rx_mode support to register unicast and multicast
address filters for enic devices
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver now uses Generic Receive Offload, not the older LRO.
Change references to LRO in names and comments.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass reference to napi instead of enic device to the isr that services receive queue.
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted here.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
rq and tq are both protected by tx queue lock, so we can simply use
the lockless variants of skb_queue.
skb_queue_splice_tail_init() is used instead of the open coded and slow
one.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
These debug stats are not exported, and become useless.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Long before this driver went into mainline, it had support for
multiple TX queues per port, with lockless TX enabled. Since Linux
did not know anything of this, filling up any hardware TX queue would
stop the core TX queue and multiple hardware TX queues could fill up
before the scheduler reacted. Thus it was necessary to keep a count
of how many TX queues were stopped and to wake the core TX queue only
when all had free space again.
The driver also previously (ab)used the per-hardware-queue stopped
flag as a counter to deal with various things that can inhibit TX, but
it no longer does that.
Remove the per-channel tx_stop_count, tx_stop_lock and
per-hardware-queue stopped count and just use the networking core
queue state directly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
I noticed that one of the post-2.6.36 patches broke runtime PM of the
r8169 on my MSI Wind test machine in such a way that the link was not
brought up after reconnecting the network cable.
In the process of debugging the issue I realized that we only should
invoke the runtime PM functions in rtl8169_check_link_status() when
link change is reported and if we do so, the problem goes away.
Moreover, this allows rtl8169_runtime_idle() to be simplified quite
a bit.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x_src_init_t2() is used only when BCM_CNIC is defined.
So, to avoid a compilation warning, we won't define it unless
BCM_CNIC is defined.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the LSO code work on BE platforms: parsing_data field of
a parsing BD (PBD) for 57712 was improperly composed which made FW read wrong
values for TCP header's length and offset and, as a result, the corresponding
PCI device was performing bad DMA reads triggering EEH.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is definitly a problem, that some option cards send up broken
IP pakets leading to corrupted IP packets. These corruptions aren't
detected, because the driver claims that the packets are already
checksummed. This change removes the CHECKSUM_UNNECESSARY option
and let IP detect broken data.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A while back I made some changes to enable netpoll in the bonding driver. Among
them was a per-cpu flag that indicated we were in a path that held locks which
could cause the netpoll path to block in during tx, and as such the tx path
should queue the frame for later use. This appears to have given rise to a
regression. If one of those paths on which we hold the per-cpu flag yields the
cpu, its possible for us to come back on a different cpu, leading to us clearing
a different flag than we set. This results in odd netpoll drops, and BUG
backtraces appearing in the log, as we check to make sure that we only clear set
bits, and only set clear bits. I had though briefly about changing the
offending paths so that they wouldn't sleep, but looking at my origional work
more closely, it doesn't appear that a per-cpu flag is warranted. We alrady
gate the checking of this flag on IFF_IN_NETPOLL, so we don't hit this in the
normal tx case anyway. And practically speaking, the normal use case for
netpoll is to only have one client anyway, so we're not going to erroneously
queue netpoll frames when its actually safe to do so. As such, lets just
convert that per-cpu flag to an atomic counter. It fixes the rescheduling bugs,
is equivalent from a performance perspective and actually eliminates some code
in the process.
Tested by the reporter and myself, successfully
Reported-by: Liang Zheng <lzheng@redhat.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Johannes Berg <johannes.berg@intel.com>
The current EEPROM reading code has some layout
assumptions that now turned out to be false with
some newer versions of the EEPROM. Luckily, we
can avoid all such assumptions by using data in
the EEPROM itself, so implement using that.
However, for risk mitigation purposes, keep the
old reading code for current hardware for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Some fields we didn't previously use from the
enhanced TX power structure will be needed in
the next patch, so rename them to their correct
names to be able to use them and change code
reading them accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Description by Hauke:
"If CONFIG_ATH_DEBUG=y is set ATH_DBG_WARN_ON_ONCE uses WARN_ON_ONCE and
returns something, but if CONFIG_ATH_DEBUG is not set it does not return
anything. Now ATH_DBG_WARN_ON_ONCE is used in the boolean expression in
an if case and is not returning anything and causes a compile error.
CC [M] /drivers/net/wireless/ath/ath9k/main.o
/drivers/net/wireless/ath/ath9k/main.c: In function ‘ath_isr’:
/drivers/net/wireless/ath/ath9k/main.c:769: error: expected expression
before ‘do’
make[5]: *** [/drivers/net/wireless/ath/ath9k/main.o] Error 1
make[4]: *** [/drivers/net/wireless/ath/ath9k] Error 2"
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AHB bus support patchset moved the table "Known PCI ids" from base.c
to pci.c - unfortunately, MODULE_DEVICE_TABLE() was not transferred.
With this fix 'modinfo ath5k' lists the alias -> pci-id lines, again.
The issue was introduced by:
commit e5b046d86f
"ath5k: Move PCI bus functions to separate file."
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/can/slcan.c: In function 'slcan_open':
drivers/net/can/slcan.c:568: error: dereferencing pointer to incomplete type
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suspend requires the device to be in fullsleep otherwise upon
resume the device becomes unresponsive. We need to ensure
that when we want the device to go to sleep it yields to
the request, otherwise we'll have a useless devices upon
resume. Warn when changing the power fails as we need
to look into these issues.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should not be idle when we get the ATH9K_INT_TIM_TIMER,
otherwise its a sign of something broken in our design with
our idle state machine and mac80211. Skip these and WARN once
just in case this is triggerable.
Cc: Paul Stewart <pstew@google.com>
Cc: Amod Bodas <amod.bodas@atheros.com>
signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This let us avoid double addressing while still having reg check.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Order was changed in specs. For writing arrays we have designed bulk function
which makes use of auto increment and do not write table address over and over.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It can be NULL according to docs, and logging showed it
to be NULL in practice.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable the port when disabling countermeasures, and disable it on
enabling countermeasures.
This bug causes the response of the system to certain attacks to be
ineffective.
It also prevents wpa_supplicant from getting scan results, as
wpa_supplicant disables countermeasures on startup - preventing the
hardware from scanning.
wpa_supplicant works with ap_mode=2 despite this bug because the commit
handler re-enables the port.
The log tends to look like:
State: DISCONNECTED -> SCANNING
Starting AP scan for wildcard SSID
Scan requested (ret=0) - scan timeout 5 seconds
EAPOL: disable timer tick
EAPOL: Supplicant port status: Unauthorized
Scan timeout - try to get results
Failed to get scan results
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
Starting AP scan for wildcard SSID
Scan requested (ret=-1) - scan timeout 5 seconds
Failed to initiate AP scan.
Reported by: Giacomo Comes <comes@naic.edu>
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
... and interface up.
In these situations, you are usually trying to connect to a new AP, so
keeping TKIP countermeasures active is confusing. This is already how
the driver behaves (inadvertently). However, querying SIOCGIWAUTH may
tell userspace that countermeasures are active when they aren't.
Clear the setting so that the reporting matches what the driver has
done..
Signed-off by: David Kilroy <kilroyd@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
David S. Miller