fix the following 'make headers_check' warnings:
usr/include/asm-powerpc/kvm.h:23: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-powerpc/kvm.h:26: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warning:
usr/include/asm-powerpc/elf.h:5: include of <linux/types.h> is preferred over <asm/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
fix the following 'make headers_check' warnings:
usr/include/asm-powerpc/bootx.h:12: include of <linux/types.h> is preferred over <asm/types.h>
usr/include/asm-powerpc/bootx.h:57: found __[us]{8,16,32,64} type without #include <linux/types.h>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
This patch ensures that memory gets properly mapped into the PCI
address space. Without this patch, the memory window BAR is left
at whatever value happened to be loaded into the BAR when Linux
was booted. Without this patch, memory could end up getting mapped
at any of the 1G address boundaries instead of at '0' where Linux
expects it.
Similarly, this patch also ensures that the internally memory mapped
registers (IMMR) are mapped to the correct PCI address range.
Without this patch, PCI appears to work correctly until a PCI
device is inserted which DMAs into memory.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
_PAGE_COHERENT is now always set in _PAGE_RAM resp. PAGE_KERNEL.
Thus it has to be masked out, if the BAT mapping should be non
cacheable or CPU_FTR_NEED_COHERENT is not set.
This will work on normal SMP setups because we force-set
CPU_FTR_NEED_COHERENT as part of CPU_FTR_COMMON on SMP.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the VIO bus code the wrappers for dma alloc_coherent and free_coherent
calls are rounding to IOMMU_PAGE_SIZE. Taking a look at the underlying
calls, the actual mapping is promoted to PAGE_SIZE. Changing the
rounding in these two functions fixes under-reporting the entitlement
used by the system. Without this change, the system could run out of
entitlement before it believes it has and incur mapping failures at the
firmware level.
Also in the VIO bus code, the wrapper for dma map_sg is not exiting in
an error path where it should. Rather than fall through to code for the
success case, this patch adds the return that is needed in the error path.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove some leftover cruft from the arch/ppc days
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Probe the new mdio node added by b31a1d8b. Fix kernel panic problem when
gianfar driver wants to get the of_platform_device of that mdio.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that all EEPROM drivers live in the same place, let's harmonize
their symbol names.
Also fix eeprom's dependencies, it definitely needs sysfs, and is no
longer experimental after many years in the kernel tree.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Convert the Warp platform to use the newly merged NDFC driver
- warp.dts changed to work with ndfc
- warp-nand.c no longer needed
- removed obsolete rev A support from cuboot-warp.c
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Added additional information for type and compatibility strings and
interrupt information to the SDRAM0 memory-controller device tree
nodes for AMCC PowerPC 405EX[r]-based boards to facilitate binding
with the new "ibm,sdram-4xx-ddr2" EDAC memory controller adapter driver.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
arm, arm/mach-integrator and powerpc were missing
.data.percpu.page_aligned in their percpu output section definitions.
Add it.
Signed-off-by: Tejun Heo <tj@kernel.org>
The PAPR says that the property for specifying the number of SLBs should
be called "slb-size". We currently only look for "ibm,slb-size" because
this is what firmware actually presents.
This patch makes us look for the "slb-size" property as well and in
preference to the "ibm,slb-size". This should future proof us if
firmware changes to match PAPR.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc: is_hugepage_only_range() must account for both 4kB and 64kB slices
The subpage_prot syscall fails on second and subsequent calls for a given
region, because is_hugepage_only_range() is mis-identifying the 4 kB
slices when the process has a 64 kB page size.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes compiler warnings:
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 2 of 'ps3_repository_read_mm_info' from incompatible pointer type
arch/powerpc/platforms/ps3/mm.c:1205: warning: passing argument 3 of 'ps3_repository_read_mm_info' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This fixes these compiler warning:
arch/powerpc/platforms/ps3/interrupt.c:109: warning: passing argument 2 of 'clear_bit' from incompatible pointer type
arch/powerpc/platforms/ps3/interrupt.c:130: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We just fix up the reference parameters as the others are dealt with by
arithmetic promotion rules and don't cause warnings.
This removes warnings like this:
arch/powerpc/platforms/ps3/interrupt.c:327: warning: passing argument 1 of 'lv1_construct_event_receive_port' from incompatible pointer type
Also, these:
drivers/ps3/ps3-vuart.c:462: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
drivers/ps3/ps3-vuart.c:592: warning: passing argument 4 of 'ps3_vuart_raw_read' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Push the dma_addr_t type usage all the way down to where the actual
values are manipulated.
Now that u64 is "unsigned long long", this removes warnings like:
arch/powerpc/platforms/ps3/system-bus.c:532: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
arch/powerpc/platforms/ps3/system-bus.c:649: warning: passing argument 4 of 'ps3_dma_map' from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Also silences this warning:
arch/powerpc/platforms/ps3/setup.c:275: warning: initialization from incompatible pointer type
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (29 commits)
powerpc/83xx: Move mcu_mpc8349emitx driver out of drivers/i2c/chips/
powerpc/83xx: Make serial ports work on MPC8315E-RDB w/ FSL U-Boots
powerpc/e500mc: Doorbells need to be taken w/exceptions disabled
powerpc: Enable PS3 options and QPACE in ppc64_defconfig
powerpc/powermac: Fix occasional SMP boot failure
powerpc/cacheinfo: Rename cache_dir per-cpu variable
hvc_console: Use kzalloc() instead of kmalloc() + memset()
hvc_console: Do not set low_latency when using interrupts
hvc_console: Call free_irq() only if request_irq() was successful
hvc_console: Change an mb() to smp_mb() and add some comments
powerpc: Cleanup from l64 to ll64 change: drivers/net
powerpc: Cleanup from l64 to ll64 change: drivers/char
powerpc: Cleanup from l64 to ll64 change: arch code
powerpc: Change u64/s64 to a long long integer type
powerpc/kexec: Check crash_base for relocatable kernel
powerpc: Make dummy section a valid note header
Xilinx: SPI: updated driver for device tree
drivers/of: Add the of_find_i2c_device_by_node function.
powerpc/xsysace: add compatible string for non-ipcore instance
powerpc/mpc52xx: remove dead code from GPIO driver
...
* 'syscalls' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (44 commits)
[CVE-2009-0029] s390 specific system call wrappers
[CVE-2009-0029] System call wrappers part 33
[CVE-2009-0029] System call wrappers part 32
[CVE-2009-0029] System call wrappers part 31
[CVE-2009-0029] System call wrappers part 30
[CVE-2009-0029] System call wrappers part 29
[CVE-2009-0029] System call wrappers part 28
[CVE-2009-0029] System call wrappers part 27
[CVE-2009-0029] System call wrappers part 26
[CVE-2009-0029] System call wrappers part 25
[CVE-2009-0029] System call wrappers part 24
[CVE-2009-0029] System call wrappers part 23
[CVE-2009-0029] System call wrappers part 22
[CVE-2009-0029] System call wrappers part 21
[CVE-2009-0029] System call wrappers part 20
[CVE-2009-0029] System call wrappers part 19
[CVE-2009-0029] System call wrappers part 18
[CVE-2009-0029] System call wrappers part 17
[CVE-2009-0029] System call wrappers part 16
[CVE-2009-0029] System call wrappers part 15
...
Add swab.h to kbuild.asm and remove the individual entries from
each arch, mark as unifdef as some arches have some kernel-only
bits inside.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This enables the use of syscall wrappers to do proper sign extension
for 64-bit programs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This patch is used to help Jean Delvare to get rid of drivers/i2c/chips/
directory. The new location suggested by Kumar Gala: as the driver is
83xx specific it's placed into arch/powerpc/platforms/83xx/.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL U-Boots use /soc8315@e0000000 node to search and fixup serial
nodes' clock-frequency properties. Though in upstream kernels we use
new naming convention -- for IMMR address space dts files specify
/immr@e0000000 nodes.
This makes FSL U-Boots fail to fixup the clock frequencies, and that
leads to serial ports misbehaviour. We can workaround the issue by
filling the clock frequency values manually.
p.s. For the same reason FSL U-Boots fail to fixup MAC addresses for
ethernet nodes, so users should either change the .dts file locally
or set MAC address via `ifconfig hw ether' command.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We use Doorbell interrupts for IPIs and thus we need to make sure we aren't
interrupted in the process of processing the IPI.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Dave Liu <daveliu@freescale.com>
To increase the amount of code that's built for a defconfig build.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The PowerMac kernel occasionally fails to bring up the secondary CPUs on
SMP, the trigger factor seem to be fairly random and related to location
of code and data.
This appears to be due to the initial loading of the TOC value by the
secondary processor which now happens before we clear HID4:RM_CI (Real
Mode Cache Invalidate). This bit should really be cleared before we do
any load or store other than fetching code.
This fix works based on the assumption that all SMP 64-bit PowerMacs use
variants of the 970, which fortunately is true, by explicitely clearing
that bit, adding an slbia for good measure as RM_CI mode is known to
create bogus ERAT entries.
I also removed some spurrious debug output that was left enabled by
mistake while at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The per_cpu__ prefix on DECLARE_PER_CPU'd variables is going away;
rename cache_dir to cache_dir_pcpu.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert arch/powerpc/ over to long long based u64:
-#ifdef __powerpc64__
-# include <asm-generic/int-l64.h>
-#else
-# include <asm-generic/int-ll64.h>
-#endif
+#include <asm-generic/int-ll64.h>
This will avoid reoccuring spurious warnings in core kernel code that
comes when people test on their own hardware. (i.e. x86 in ~98% of the
cases) This is what x86 uses and it generally helps keep 64-bit code
32-bit clean too.
[Adjusted to not impact user mode (from paulus) - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enforce that the crash kernel region never overlaps the current kernel,
as it will be written directly on kexec load.
Also, default to the previous KDUMP_KERNELBASE if the start is 0.
Other architectures (x86, ia64) state that specifying the start address
0 (or omitting it) will result in the kernel allocating it. Before the
relocatable patch in 2.6.28, powerpc would adjust any other start value
to the hardcoded KDUMP_KERNELBASE of 32M.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are declaring the dummy section (used to work around a binutils
bug) as PT_NOTE, but we don't have enough bytes for it to be a valid
note header, and kexec userspace complains:
Warning: Elf Note name is not null terminated
Warning: append= option is not passed. Using the first kernel root partition
Warning: Elf Note name is not null terminated
Instead of using the arbitray value 0xf177 (aka "fill"), declare a
no-name no-description note of type 0.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Support for the FPGA based watchdog timer on GE Fanuc's SBC610.
This patch enables one of the watchdog timers found on the SBC610. There are
two identical watchdog timers at different offsets in the above mentioned
boards, however the current driver is only capable of supporting one of them.
The watchdog timers are also capable of generating interrupts at a
user-configurable threshold, though support for this operation is currently
not supported by the driver.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This updates the cpufreq drivers in arch/powerpc so they build again
after the core cpufreq changes that broke them in commit
in835481d9bcd65720b473db6b38746a74a3964218.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MPC5200 PIC driver doesn't correctly update the .status field of
the irq_desc structure when the set_type hook is called. This patch
adds the required code.
Also cleans up the external IRQ typename field to be something easier
to read (very minor).
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
strcmp on NULL results in a segmentation fault, also, remove the second,
redundant test on dev
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile: (31 commits)
powerpc/oprofile: fix whitespaces in op_model_cell.c
powerpc/oprofile: IBM CELL: add SPU event profiling support
powerpc/oprofile: fix cell/pr_util.h
powerpc/oprofile: IBM CELL: cleanup and restructuring
oprofile: make new cpu buffer functions part of the api
oprofile: remove #ifdef CONFIG_OPROFILE_IBS in non-ibs code
ring_buffer: fix ring_buffer_event_length()
oprofile: use new data sample format for ibs
oprofile: add op_cpu_buffer_get_data()
oprofile: add op_cpu_buffer_add_data()
oprofile: rework implementation of cpu buffer events
oprofile: modify op_cpu_buffer_read_entry()
oprofile: add op_cpu_buffer_write_reserve()
oprofile: rename variables in add_ibs_begin()
oprofile: rename add_sample() in cpu_buffer.c
oprofile: rename variable ibs_allowed to has_ibs in op_model_amd.c
oprofile: making add_sample_entry() inline
oprofile: remove backtrace code for ibs
oprofile: remove unused ibs macro
oprofile: remove unused components in struct oprofile_cpu_buffer
...
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (53 commits)
serial: Add driver for the Cell Network Processor serial port NWP device
powerpc: enable dynamic ftrace
powerpc/cell: Fix the prototype of create_vma_map()
powerpc/mm: Make clear_fixmap() actually work
powerpc/kdump: Use ppc_save_regs() in crash_setup_regs()
powerpc: Export cacheable_memzero as its now used in a driver
powerpc: Fix missing semicolons in mmu_decl.h
powerpc/pasemi: local_irq_save uses an unsigned long
powerpc/cell: Fix some u64 vs. long types
powerpc/cell: Use correct types in beat files
powerpc: Use correct type in prom_init.c
powerpc: Remove unnecessary casts
mtd/ps3vram: Use _PAGE_NO_CACHE in memory ioremap
mtd/ps3vram: Use msleep in waits
mtd/ps3vram: Use proper kernel types
mtd/ps3vram: Cleanup ps3vram driver messages
mtd/ps3vram: Remove ps3vram debug routines
mtd/ps3vram: Add modalias support to the ps3vram driver
mtd/ps3vram: Add ps3vram driver for accessing video RAM as MTD
powerpc: Fix iseries drivers build failure without CONFIG_VIOPATH
...
When I review ocfs2 code, find there are 2 typos to "successfull". After
doing grep "successfull " in kernel tree, 22 typos found totally -- great
minds always think alike :)
This patch fixes all the similar typos. Thanks for Randy's ack and comments.
Signed-off-by: Coly Li <coyli@suse.de>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Vlad Yasevich <vladislav.yasevich@hp.com>
Cc: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the SPU event based profiling funcitonality for the
IBM Cell processor. Previously, the CELL OProfile kernel code supported
PPU event, PPU cycle profiling and SPU cycle profiling. The addition of
SPU event profiling allows the users to identify where in their SPU code
various SPU evnets are occuring. This should help users further identify
issues with their code. Note, SPU profiling has some limitations due to HW
constraints. Only one event at a time can be used for profiling and SPU event
profiling must be time sliced across all of the SPUs in a node.
The patch adds a new arch specific file to the OProfile file system. The
file has bit 0 set to indicate that the kernel supports SPU event profiling.
The user tool must check this file/bit to make sure the kernel supports
SPU event profiling before trying to do SPU event profiling. The user tool
check is part of the user tool patch for SPU event profiling.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch restructures and cleans up the code a bit to make it
easier to add new functionality later. The patch makes no
functional changes to the existing code.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch enables dynamic ftrace. The PowerPC port was dependent on
other code not yet in mainline. Now that the code is, we can now
let PowerPC compile with dynamic ftrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The clear_fixmap() routine issues map_page() with flags set to 0.
Currently this causes a BUG_ON() inside the map_page(), as it assumes
that a PTE should be clear before mapping.
This patch makes the map_page() to trigger the BUG_ON() only if the
flags were set.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch replaces internal registers dump implementation with
ppc_save_regs(). From now on PPC64 and PPC32 are using the same
code for crash_setup_regs().
NOTE: The old regs dump implementation was capturing SP (r1) directly
as is, so you could see crash_kexec() function on top of the back-trace.
But ppc_save_regs() goes up one stack frame, so you'll not see it
anymore, at the top-level you'll see who actually triggered the crash
dump instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale PowerPC specific gianfar driver (gig-e) uses
cacheable_memzero for performance reasons we need to export
the symbol to allow the driver to be built as a module.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a brown paper bag from one of my earlier patches that
breaks build on 40x and 8xx.
And yes, I've now added 40x and 8xx to my list of test configs :-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[Split from a larger patch - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
in/out_be64() work on u64s.
The first parameter to ppc_md.ioremap is a phys_addr_t.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Only pass the address of a u64 if that is what the function requires.
[Split out of a larger patch - sfr]
[update comment - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tce_entryp is a "u64 *" not an "unsigned long *".
[Split from a large patch -sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
of_get_flat_dt_prop() returns a "void *", so we don't need to cast when
assigning its result to a pointer variable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update ps3vram driver to use the new ps3 three id modalias support.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ps3vram driver, which exposes unused video RAM on the PS3 as a MTD
device suitable for storage or swap. Fast data transfer is achieved
using a local cache in system RAM and DMA transfers via the GPU.
Signed-off-by: Vivien Chappelier <vivien.chappelier@free.fr>
Signed-off-by: Jim Paris <jim@jtan.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
iSeries dependent drivers fail to build, when CONFIG_VIOPATH is disabled.
Fix the problem by making those drivers select it.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable RELOCATABLE option if user selects CRASH_DUMP option. Without this
patch user has to first select RELOCATABLE option and then has to enable
CRASH_DUMP option.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So change the flags member of struct spu from u64 to unsigned long.
This change will also prevent some warnings when we change u64 to unsigned
long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These ioctls take a struct serial_rs485
(see linux/serial.h) as argument. They are already available
on x86. This patch adds them for the powerpc architecture.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
X has been failing to start on my quad G5 powermac since commit
1fd0f52583 ("powerpc: Fix domain numbers
in /proc on 64-bit") went in. The reason is that the change allows X
to see the PCI-PCI bridge above the video card (previously it was
obscured by the fact that there were two "00" directories in
/proc/bus/pci), and the pciconfig_iobase system call on the bridge is
failing because of a hack that we have to return information about the
AGP bus when X asks about bus 0. This machine doesn't have an AGP bus
(it has PCI Express) and so the pciconfig_iobase call is returning -1,
which ultimately causes X to fail to start.
This fixes it by checking that we have an AGP bridge before
redirecting the pciconfig_iobase call to return information about the
AGP bus. With this, X starts successfully both on a quad G5 with
PCI Express and on an older dual G5 with AGP.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@
- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@
- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code for providing processor cache information in sysfs
has the following deficiencies:
- several complex functions that are hard to understand
- implicit recursion (cache_desc_release -> kobject_put -> cache_desc_release)
- explicit recursion (create_cache_index_info)
- use of two per-cpu arrays when one would suffice
- duplication of work on systems where CPUs share cache
Also, when I looked at implementing support for a shared_cpu_map
attribute, it was pretty much impossible to handle hotplug without
checking every single online CPU's cache_desc list and fixing things
up... not that this is a hot path, but it would have introduced
O(n^2)-ish behavior during boot. Addressing this involved rethinking
the core data structures used, which didn't lend itself to an
incremental approach.
This implementation maintains a "forest" (potentially more than one
tree) of cache objects which reflects the system's cache topology.
Cache objects are instantiated as needed as CPUs come online. A
per-cpu array is used mainly for sysfs-related bookkeeping; the
objects in the array just point to the appropriate points in the
forest.
This maintains compatibility with the existing code and includes some
enhancements:
- Implement the shared_cpu_map attribute, which is essential for
enabling userspace to discover the system's overall cache topology.
- Use cache-block-size properties if cache-line-size is not available.
I chose to place this implementation in a new file since it would have
roughly doubled the size of sysfs.c, which is already kind of messy.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The non-zero return from the prepare callback is returned by sys_kexec_load()
to userspace, indicating that kexec is not supported on the machine.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch makes the default install script (arch/powerpc/boot/install.sh)
copy the bootable image files into the install directory. Before this
patch only the vmlinux image file was copied.
This patch makes the default 'make install' command useful for embedded
development when $(INSTALL_PATH) is set in the environment.
As a side effect, this patch changes the calling convention of the
install.sh script. Instead of a single 5th parameter, the script is now
passed a list of all the target images stored in the $(image-y) Makefile
variable. This should be backwards compatible with existing install scripts
since it just adds additional arguments and does not change existing ones.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Both users of careful_allocation() immediately memset() the
result. So, just do it in one place.
Also give careful_allocation() a 'z' prefix to bring it in
line with kzmalloc() and friends.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we memset() the result in both of the uses here,
just make careful_alloc() return a virtual address.
Also, add a separate variable to store the physial
address that comes back from the lmb_alloc() functions.
This makes it less likely that someone will screw it up
forgetting to convert before returning since the vaddr
is always in a void* and the paddr is always in an
unsigned long.
I admit this is arbitrary since one of its users needs
a paddr and one a vaddr, but it does remove a good
number of casts.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we fail a bootmem allocation, the bootmem code itself
panics. No need to redo it here.
Also change the wording of the other panic. We don't
strictly have to allocate memory on the specified node.
It is just a hint and that node may not even *have* any
memory on it. In that case we can and do fall back to
other nodes.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The behavior in careful_allocation() really confused me
at first. Add a comment to hopefully make it easier
on the next doofus that looks at it.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes some unbalanced OF node references in the
powermac code
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's a problem on some embedded platforms when we re-assign
everything on PCI, such as 44x. The generic code tries to avoid
assigning devices to addresses overlapping the low legacy
addresses such as VGA hard decoded areas using constants that
are unfortunately no good for us, as they don't take into account
the address translation we do to access PCI busses.
Thus we end up allocating things like IO BARs to 0, which is
technically legal, but will shadow hard decoded ports for use
by things like VGA cards.
This works around it by attempting to reserve legacy regions
before we try to assign addresses.
NOTE: This may have nasty side effects in cases I haven't tested
yet:
- We try to use FW mappings (ie. powermac) and the FW has allocated
a conflicting address over those legacy regions. This will typically
happen. I would expect the new code to just fail with an informative
message without harm but I haven't had a chance to test that scenario
yet.
- A device with fixed BARs overlapping those legacy addresses such
as an IDE controller in legacy mode is in the system. I don't know
for sure yet what will happen there, I have to test :-)
Ideally, we should change PCIBIOS_MIN_IO/MIN_MEM accross the board
to take a bus pointer so they can provide appropriate per-bus translated
values to the generic code but that's a more invasive patch. I will
do that in the future, but in the meantime, this fixes the problem
locally
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
