The Motorola PrPMC280 and PrPMC2800 processor modules sit on an F101 or
PrPMC2800 baseboard, respectively. There are several variants of each
type of processor module which can have different amounts of memory,
amounts of FLASH, cpu frequencies, and an mv64360 or an mv64362.
The bootwrapper code for that platform reads VPD from an I2C EEPROM
to determine the processor module variant. From the variant, the
amount of memory, etc. is determined and the device tree is updated
accordingly. If the variant cannot be determined (e.g., corrupted
VPD or a previously unknown variant), the property values already
in the device tree are used.
Also, the firmware for those platforms does not completely configure
the mv64x60 host bridge so that configuration is done here.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the device tree source file for the prpmc2800 line of processor PMCs.
Several of the property values are updated by the bootwrapper but sane
defaults have been chosen in case the bootwrapper can't determine the
exact processor board variant. The defaults should allow the kernel
to boot despite having non-optimal device tree property values.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some platforms support a variety processor modules with no method of
determining which exact processor module is being used except by
examining Vital Product Data (VPD). The modules may have different
amounts of memory, clock frequencies, etc. so reading the VPD becomes
necessary to correctly set properties in the device tree before its
passed to the kernel.
Often the VPD is stored in I2C EEPROMs so an I2C driver becomes necessary.
This I2C driver is for the I2C controller that's embedded on the Marvel
mv64x60 line of host bridges.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The bootwrapper requires a serial driver to allow cmdline editing
and information reporting on the console. This driver is required
by platforms that boot a zImage and use the MPSC for the console.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The mv64x60 host bridge has many windows between its various components
(cpu, system memory, ethernet ctlr, MPSC, DMA ctlr, PCI MEM, PCI I/O).
Unfortunately, the firmware on some of mv64x60-based platforms do not
properly or completely configure those windows (e.g., MPSC->system memory
windows not configured or CPU->PCI MEM space not configured).
So, the missing configuration needs to be done in either the bootwrapper
or in the kernel. To keep the kernel as clean as possible, it is done
in the bootwrapper. Note that I/O controller configuration is NOT being
done, its only the windows to allow the I/O controllers and other components
to access memory, etc. that is being done--drivers assume that their
controllers can already access system memory).
Table of routines and the windows they configure:
mv64x60_config_ctlr_windows() ENET->System Memory
MPSC->System Memory
IDMA->System Memory
mv64x60_config_pci_windows() PCI MEM->System Memory
PCI I/O->Bridge's Registers
mv64x60_config_cpu2pci_window() CPU->PCI MEM
CPU->PCI I/O
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add 'zImage.dts' and 'zImage.dts_initrd' build rules that automatically
compile and wrap a dts file from arch/powerpc/boot/dts into the zImage file.
The resulting zImage will be arch/powerpc/boot/zImage.dts.<platform> and
arch/powerpc/boot/zImage.dts_initrd.<platform>, respectively.
Having separate rules allows the user to choose whether to include a device
tree--and which device tree--at build time. This is useful when one Makefile
target builds a zImage that runs on several platforms except for differing
device trees. By just setting CONFIG_DEVICE_TREE and running "make zImage.dts"
the exact zImage you want is built without Makefile bloat or manually running
the wrapper script.
The dts file is expected to be arch/powerpc/boot/dts/$(CONFIG_DEVICE_TREE)
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The boot wrapper platform init code on 83xx and 85xx using the cuboot
platform type was incorrectly assuming that u-boot supplied the size
of the initrd, whereas it actually supplies the end address. This
fixes it.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The MPC834x_MDS device tree's PCI non-prefetchable MMIO range was
specified incorrectly. Both the local and bus addresses start at
0x90000000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC832x_MDS device tree's PCI non-prefetchable MMIO range was
specified incorrectly. Both the local and bus addresses start at
0x90000000.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This adds platform support code for the Ebony (440GP) evaluation
board. This includes both code in arch/powerpc/platforms/44x for
board initialization, and zImage wrapper code to correctly tweak the
flattened device tree based on information from the firmware. The
zImage supports both IBM OpenBIOS (aka "treeboot") and old versions of
uboot which don't support a flattened device tree.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a device tree for the Ebony evaluation board (440GP based). This
tree is not complete or finalized. This tree needs a version of dtc
recent enough to include reference-to-labels to process.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add fsl-i2c to mpc5200 i2c node in device tree, and enable FSL_SOC.
Tested to work with built-in eeprom on lite5200b.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes a couple of missing dependencies in
arch/powerpc/boot/Makefile. First, it ensures that the zlib.h header
is linked in before attempting to build gunzip_util.o, as it is,
building gunzip_util.o usually works, but not always depending on make
order.
Second, it makes the final images which are built using a dts
dependent on that dts, so the image will be correctly rebuilt if the
dts changes. This in turn requires fixing the definition of the dts
variable. CONFIG_DEVICE_TREE from Kconfig will have quotes around it,
which don't matter when passing the variable to a shell, but which
need to be removed when incorporating it into a filename for make's
use.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows the zImage target to once again be used to build
all supported image types, rather than requiring an explicit
"make uImage" to avoid failing to create an unneeded cuImage.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes a few small cleanups to the cuboot code.
- It removes the double layered selection of images, via
cuboot-plat-y, instead having the cuboot platforms directly select a
suitable image-y (this changes the name of the final cuboot image from
plain cuImage to cuImage.<platform>).
- Factors out some code in the wrapper that's potentially
useful to platforms other than uboot.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
phy-connection-type now supersedes the interface property.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dt_xlate_reg() looks up the 'reg' property in the specified node
to get the address and size to translate. Add dt_xlate_addr()
which is passed in the address and size to translate.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A usage of CONFIG_DEVICE_TREE got accidentally truncated; this
fix allows out-of-tree dts files to work.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The uppermost part of memory is where u-boot puts the stack, so don't
include that in the heap. It's not currently causing problems, as the
current code allocates from the bottom of the heap, but this will keep
things from potentially breaking if a future implementation were to
allocate from the top.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes a few bugs in how dt_xlate_reg() handles address arrays:
1. copy_val() was copying into the wrong end of the array, resulting
in random stack garbage at the other end.
2. dt_xlate_reg() was getting the result from the wrong end of the array.
3. add_reg() and sub_reg() were treating the arrays as
little-endian rather than big-endian.
4. add_reg() only returned an error on a carry out of the entire
array, rather than out of the naddr portion.
5. The requested reg resource was checked to see if it exceeded
the size of the reg property, but not to see if it exceeded the
size of the buffer.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the error message in gunzip_exactly to be more verbose.
Besides the identifier being unrelated to the current function name,
the user had no indication if the corruption was near the beginning
or the end.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
make help on powerpc says make install is available.
But it failed due to no rule to make install.
This patch enables make install to work.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use `unsigned long' for malloc sizes, to match common practice and types used
by most callers and callees.
Also use `unsigned long' for integers representing pointers in simple_alloc.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@eu.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds cuboot support for MPC83xx platforms.
A device tree used with this must have linux,stdout-path in /chosen and
linux,network-index in any network device nodes that need mac addresses
assigned.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This file describes the bd_t struct, which is used by old versions of
U-boot to pass information to the kernel. Platform code that needs to
interoperate with such firmware can use this; it should not be used for
anything new.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The cuImage target will build a uImage with bootwrapper code and a device
tree. The default device tree and platform file are determined by the
kernel configuration.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 79c8541924 introduced code to move
the initrd if it was in a place where it would get overwritten by the
kernel image. Unfortunately this exposed the fact that the code that
checks whether the values passed in r3 and r4 are intended to indicate
the start address and size of an initrd image was not as thorough as the
kernel's checks. The symptom is that on OF-based platforms, the
bootwrapper can cause an exception which causes the system to drop back
into OF.
Previously it didn't matter so much if the code incorrectly thought that
there was an initrd, since the values for start and size were just passed
through to the kernel. Now the bootwrapper needs to apply the same checks
as the kernel since it is now using the initrd data itself (in the process
of copying it if necessary). This adds the code to do that.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Our kernels put everything in the first load segment, and we read that.
Instead of decompressing to the end of the gzip stream or supplied image
and hoping we get it all, decompress the expected size and complain if
it is not available.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit a9903811bf missed two uses of the
the .gz suffix in the wrapper script and didn't clean the additonal
possibly cached files.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
crt0.S had provisions to provide run address relocaton to got2 and
cache flush, but not on the bss clear or stack pointer load. Apply
the same fixup for them.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ELF parsing routines local to arch/powerpc/boot/main.c are useful
to other callers therefore move them to their own file.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dt_xlate_reg() uses the ranges properties of a node's parentage to find
the absolute physical address of the node's registers.
The ns16550 driver uses this when no virtual-reg property is found.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up how the zImage code manipulates the kernel
command line. Notable improvements from the old handling:
- Command line manipulation is consolidated into a new
prep_cmdline() function, rather than being scattered across start()
and some helper functions
- Less stack space use: we use just a single global command
line buffer, which can be initialized by an external tool as before,
we no longer need another command line sized buffer on the stack.
- Easier to support platforms whose firmware passes a
commandline, but not a device tree. Platform code can now point new
loader_info fields to the firmware's command line, rather than having
to do early manipulation of the /chosen bootargs property which may
then be rewritten again by the core.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a library of useful device tree manipulation functions
to the zImage library, for use by platform code. These functions are
based on the hooks already in dt_ops, so they're not dependent on a
particular device tree implementation. This patch also slightly
streamlines the code in main.c using these new functions.
This is a consolidation of my work in this area with Scott Wood's
patches to a very similar end.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch provides the basic MPC8544 DS platform code and config.
Follow-up patches will add peripherals such as PCI and SATA.
Signed-off-by: Xianghua Xiao <x.xiao@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8323E Reference Development Board (RDB). The board
is a mini-ITX reference board with 64M DDR2, 16M flash, USB, PCI,
10/100 ethernet, serial, and phone ports.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a reg.h to the zImage code, with common definitions
for accessing system registers. For now, this includes functions for
retrieving the PVR and the stack pointer. This patch then uses the
new reg.h to let start() display the running stack address without
having to explicitly pass the stack as a parameter from the asm code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds the correct attributes to the zImage's versions of
printf to make gcc generate format string mismatch warnings. It also
corrects several minor problems with format strings in the zImage thus
discovered.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Before the plethora of platforms gets any worse, establish a common
rule to invoke the wrapper for any platform. Add arguments to
the rule for initrd, dts, dtb, etc. Show example usage with initrd.
Create default rules for zImage, and zImage.initrd. initrd targets
depend on the ramdisk file.
Don't consider targets for zImage.initrd that are targets for zImage.
This means uImage is no longer considered a target for zImage.initrd.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that obj-boot is in targets, we can remove (twice) it from clean-files.
zImage.initrd was missing, move zImage nearer where its used, and place
zImage.initrd next to it. Remove non-ported zImage.sandpoint, and add
auto-generation of unconfigured zImage.initrd* like image-.
Signed-off-by: Milton Miller <miltonm@bga.com>
--
Testing: did a few builds and cleans
Signed-off-by: Paul Mackerras <paulus@samba.org>
Kbuild if_changed and if_changed_dep require the use of the dummy
FORCE to get the dependencies right. Also add to targets to get
correct behavior.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some platforms might need to run some code before the zImage start, but
could otherwise use the bss clear and relocation code. Export the
start address strongly as zImage_start_lib.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a macro fatal that calls printf then exit. User must include stdio.h.
Typically replaces 3 lines with 1, although I added back some whitespace.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Mark A. Greer