Here we hook up the watch exception handler so that it sends SIGTRAP when
the hardware watch registers are triggered.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe for watch register characteristics, and report them in /proc/cpuinfo.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the main support code for the patch. Here we just add the
code, the following patches hook it up.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/include/asm/watch.h
create mode 100644 arch/mips/kernel/watch.c
This is automatically set for all MIPS32 and MIPS64 processors.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a helper routine to register tx4939ide driver and use it on
RBTX4939 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add leds-gpio platform device for controlling LEDs connected to IOC on
RBTX49XX and JMR3927 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The IOC interrupt status register on RBTX49XX only have 8 bits. Use
8-bit version of __fls() to optimize interrupt handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TXx9 SoCs have pin multiplex. Stop some controller modules which can
not be used due to pin configurations.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the rb532 code to use gpio library
and register its gpio chip.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch cleans up headers and regroups informations to
where they should reside. While moving, try to have a
consistant naming for defines.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are no longer using setup_serial_port. So just remove it
from the prom code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When there is only platform device of the same type, id = -1
should be used, fix this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces a raw read using volatiles
with a readl.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are no longer using gpio bootup state, so do not export
it and do not parse the kernel command line tag for it.
Instead we provide gpio-keys for the button the gpio bootup
state was checking.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the misuse of virtual addresses for the GPIO and third
device controller which would lead to problems while accessing ioremap'd
registers.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch moves GPIO related definitions to gpio.h and IRQ
related to irq.h
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Helper routines in txx9/rbtx4938/spi_eeprom.c is not TX4938 specific.
Move it to txx9/generic/ directory and make it works with SPI bus
number other than 0.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/txx9/generic/spi_eeprom.c
delete mode 100644 arch/mips/txx9/rbtx4938/spi_eeprom.c
Add TOSHIBA_RBTX4938_MPLEX_KEEP to keep MPLEX settings by firmware.
Also replace some printk with pr_info.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39/TX49 can enable/disable I/D cache at runtime. Add kernel options
to control them. This is useful to debug some cache-related issues,
such as aliasing or I/D coherency. Also enable CWF bit for TX49 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add prom_getenv() which can be used for YAMON. This assumes other
firmware should pass NULL for fw_arg2.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Make prom_init_cmdline() static and be called from prom_init.
* Append built-in args if the first character was '+'.
* Drop command-line args if the first character of built-in was '-'.
* Enclose args include spaces by quotes.
* TX4938_NAND_BOOT is no longer needed.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Make sure all interrupts cleared on startup
* Initialize some GPIOs
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This new gpio driver for PMC-Sierra's MSP71xx SoC allows
standard api calls for access to the general and extended
gpio's.
Signed-off-by: Patrick Glass <patrickglass@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100755 arch/mips/pmc-sierra/msp71xx/gpio.c
create mode 100755 arch/mips/pmc-sierra/msp71xx/gpio_extended.c
create mode 100755 include/asm-mips/pmc-sierra/msp71xx/gpio.h
This replaces mips's sys_ptrace32 with a compat_arch_ptrace and
enables the new generic definition of compat_sys_ptrace instead.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some machines don't have the pullup/down on their reset
pin, so configuring the reset generating pin as input makes
them reset immediately. Fix that by making reset pin direction
configurable.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'sched-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
sched debug: add name to sched_domain sysctl entries
sched: sync wakeups vs avg_overlap
sched: remove redundant code in cpu_cgroup_create()
sched_rt.c: resch needed in rt_rq_enqueue() for the root rt_rq
cpusets: scan_for_empty_cpusets(), cpuset doesn't seem to be so const
sched: minor optimizations in wake_affine and select_task_rq_fair
sched: maintain only task entities in cfs_rq->tasks list
sched: fixup buddy selection
sched: more sanity checks on the bandwidth settings
sched: add some comments to the bandwidth code
sched: fixlet for group load balance
sched: rework wakeup preemption
CFS scheduler: documentation about scheduling policies
sched: clarify ifdef tangle
sched: fix list traversal to use _rcu variant
sched: turn off WAKEUP_OVERLAP
sched: wakeup preempt when small overlap
kernel/cpu.c: create a CPU_STARTING cpu_chain notifier
kernel/cpu.c: Move the CPU_DYING notifiers
sched: fix __load_balance_iterator() for cfq with only one task
...
chsc_sstpc returns -EIO on error and 0 on success but stp_reset checks
against 1 instead of 0. chsc_sstpc used to return 1 on success, one
call location has not been updated ..
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch defines a dirty bit in the PGSTE that can be used to implement
dirty pages logging for KVM's live migration. The bit is set in the
ptep_rcp_copy function, which is called to save dirty and referenced information
from the storage key in the PGSTE. The bit can be tested and reset by KVM using
the kvm_s390_test_and_clear_page_dirty function that is introduced by this patch.
Acked-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Florian Funke <ffunke@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
EMC Symmetrix Subsystem Control I/O through CKD dasd requires a
specific parameter list sent to the array via a Perform Subsystem
Function CCW. The Symmetrix response is retrieved from the array
via a Read Subsystem Data CCW.
Signed-off-by: Nigel Hislop <hislop_nigel@emc.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Move cio's private simple udelay function to lib/delay.c and turn it
into something much more readable. So we have all implementations
at one place.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The DCSS block device driver is modified to add >2G DCSSs support and
allow a DCSS block device to map to a set of contiguous DCSSs. The
extmem code is also modified to use new Diagnose x'64' subcodes for
>2G DCSSs.
Signed-off-by: Hongjie Yang <hongjie@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* System call parameter and result access functions
* Add tracehook calls
* Split syscall_trace into two functions do_syscall_trace_enter and
do_syscall_trace_exit
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sys32_pause is a useless copy of the generic sys_pause.
(and it's certainly not there for old sparc32 binaries..)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add support for z10 HiperSockets multiwrite SBALs on output
queues. This is used on LPAR with EDDP enabled devices.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: skcipher - Use RNG interface instead of get_random_bytes
crypto: rng - RNG interface and implementation
crypto: api - Add fips_enable flag
crypto: skcipher - Move IV generators into their own modules
crypto: cryptomgr - Test ciphers using ECB
crypto: api - Use test infrastructure
crypto: cryptomgr - Add test infrastructure
crypto: tcrypt - Add alg_test interface
crypto: tcrypt - Abort and only log if there is an error
crypto: crc32c - Use Intel CRC32 instruction
crypto: tcrypt - Avoid using contiguous pages
crypto: api - Display larval objects properly
crypto: api - Export crypto_alg_lookup instead of __crypto_alg_lookup
crypto: Kconfig - Replace leading spaces with tabs
Jeremy Fitzhardinge wrote:
> I'd noticed that current tip/master hasn't been booting under Xen, and I
> just got around to bisecting it down to this change.
>
> commit 065ae73c5462d42e9761afb76f2b52965ff45bd6
> Author: Suresh Siddha <suresh.b.siddha@intel.com>
>
> x86, cpa: make the kernel physical mapping initialization a two pass sequence
>
> This patch is causing Xen to fail various pagetable updates because it
> ends up remapping pagetables to RW, which Xen explicitly prohibits (as
> that would allow guests to make arbitrary changes to pagetables, rather
> than have them mediated by the hypervisor).
Instead of making init a two pass sequence, to satisfy the Intel's TLB
Application note (developer.intel.com/design/processor/applnots/317080.pdf
Section 6 page 26), we preserve the original page permissions
when fragmenting the large mappings and don't touch the existing memory
mapping (which satisfies Xen's requirements).
Only open issue is: on a native linux kernel, we will go back to mapping
the first 0-1GB kernel identity mapping as executable (because of the
static mapping setup in head_64.S). We can fix this in a different
patch if needed.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Track the memtype for RAM pages in page struct instead of using the
memtype list. This avoids the explosion in the number of entries in
memtype list (of the order of 20,000 with AGP) and makes the PAT
tracking simpler.
We are using PG_arch_1 bit in page->flags.
We still use the memtype list for non RAM pages.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Do a global flush tlb after splitting the large page and before we do the
actual change page attribute in the PTE.
With out this, we violate the TLB application note, which says
"The TLBs may contain both ordinary and large-page translations for
a 4-KByte range of linear addresses. This may occur if software
modifies the paging structures so that the page size used for the
address range changes. If the two translations differ with respect
to page frame or attributes (e.g., permissions), processor behavior
is undefined and may be implementation-specific."
And also serialize cpa() (for !DEBUG_PAGEALLOC which uses large identity
mappings) using cpa_lock. So that we don't allow any other cpu, with stale
large tlb entries change the page attribute in parallel to some other cpu
splitting a large page entry along with changing the attribute.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: arjan@linux.intel.com
Cc: venkatesh.pallipadi@intel.com
Cc: jeremy@goop.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Interrupt context no longer splits large page in cpa(). So we can do away
with cpa memory pool code.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: arjan@linux.intel.com
Cc: venkatesh.pallipadi@intel.com
Cc: jeremy@goop.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
No alias checking needed for setting present/not-present mapping. Otherwise,
we may need to break large pages for 64-bit kernel text mappings (this adds to
complexity if we want to do this from atomic context especially, for ex:
with CONFIG_DEBUG_PAGEALLOC). Let's keep it simple!
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: arjan@linux.intel.com
Cc: venkatesh.pallipadi@intel.com
Cc: jeremy@goop.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Don't use large pages for kernel identity mapping with DEBUG_PAGEALLOC.
This will remove the need to split the large page for the
allocated kernel page in the interrupt context.
This will simplify cpa code(as we don't do the split any more from the
interrupt context). cpa code simplication in the subsequent patches.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: arjan@linux.intel.com
Cc: venkatesh.pallipadi@intel.com
Cc: jeremy@goop.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the first pass, kernel physical mapping will be setup using large or
small pages but uses the same PTE attributes as that of the early
PTE attributes setup by early boot code in head_[32|64].S
After flushing TLB's, we go through the second pass, which setups the
direct mapped PTE's with the appropriate attributes (like NX, GLOBAL etc)
which are runtime detectable.
This two pass mechanism conforms to the TLB app note which says:
"Software should not write to a paging-structure entry in a way that would
change, for any linear address, both the page size and either the page frame
or attributes."
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: arjan@linux.intel.com
Cc: venkatesh.pallipadi@intel.com
Cc: jeremy@goop.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This merges phase 1 of the x86 tree, which is a collection of branches:
x86/alternatives, x86/cleanups, x86/commandline, x86/crashdump,
x86/debug, x86/defconfig, x86/doc, x86/exports, x86/fpu, x86/gart,
x86/idle, x86/mm, x86/mtrr, x86/nmi-watchdog, x86/oprofile,
x86/paravirt, x86/reboot, x86/sparse-fixes, x86/tsc, x86/urgent and
x86/vmalloc
and as Ingo says: "these are the easiest, purely independent x86 topics
with no conflicts, in one nice Octopus merge".
* 'x86-v28-for-linus-phase1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (147 commits)
x86: mtrr_cleanup: treat WRPROT as UNCACHEABLE
x86: mtrr_cleanup: first 1M may be covered in var mtrrs
x86: mtrr_cleanup: print out correct type v2
x86: trivial printk fix in efi.c
x86, debug: mtrr_cleanup print out var mtrr before change it
x86: mtrr_cleanup try gran_size to less than 1M, v3
x86: mtrr_cleanup try gran_size to less than 1M, cleanup
x86: change MTRR_SANITIZER to def_bool y
x86, debug printouts: IOMMU setup failures should not be KERN_ERR
x86: export set_memory_ro and set_memory_rw
x86: mtrr_cleanup try gran_size to less than 1M
x86: mtrr_cleanup prepare to make gran_size to less 1M
x86: mtrr_cleanup safe to get more spare regs now
x86_64: be less annoying on boot, v2
x86: mtrr_cleanup hole size should be less than half of chunk_size, v2
x86: add mtrr_cleanup_debug command line
x86: mtrr_cleanup optimization, v2
x86: don't need to go to chunksize to 4G
x86_64: be less annoying on boot
x86, olpc: fix endian bug in openfirmware workaround
...
Write the name of the unknown vendor_id to output instead of just
"unknown".
Tag changed to 'vendor_id' as used in /proc/cpuinfo
Signed-off-by: Hans Schou <linux@schou.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch allows the use of the hardware watchdog in the
Marvell Orion series of ARM SoCs.
Signed-off-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
These are changes that have been sitting in linux-omap
and were never sent upstream.
Hopefully, it'll never happen again at least for this
driver.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
When reserving space for the hypervisor the Xen paravirt backend adds
an extra two pages (this was carried forward from the 2.6.18-xen tree
which had them "for safety"). Depending on various CONFIG options this
can cause the boot time fixmaps to span multiple PMDs which is not
supported and triggers a WARN in early_ioremap_init().
This was exposed by 2216d199b1 which
moved the dmi table parsing earlier.
x86: fix CONFIG_X86_RESERVE_LOW_64K=y
The bad_bios_dmi_table() quirk never triggered because we do DMI setup
too late. Move it a bit earlier.
There is no real reason to reserve these two extra pages and the
fixmap already incorporates FIX_HOLE which serves the same
purpose. None of the other callers of reserve_top_address do this.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add optional verbose debug - which when turned off, quiets down
userspace errors. Saves ~8k of code/data for production systems
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
If there are multiple reserved memory blocks via lmb_reserve() that are
contiguous addresses and on different NUMA nodes we are losing track of which
address ranges to reserve in bootmem on which node. I discovered this
when I recently got to try 16GB huge pages on a system with more then 2 nodes.
When scanning the device tree in early boot we call lmb_reserve() with
the addresses of the 16G pages that we find so that the memory doesn't
get used for something else. For example the addresses for the pages
could be 4000000000, 4400000000, 4800000000, 4C00000000, etc - 8 pages,
one on each of eight nodes. In the lmb after all the pages have been
reserved it will look something like the following:
lmb_dump_all:
memory.cnt = 0x2
memory.size = 0x3e80000000
memory.region[0x0].base = 0x0
.size = 0x1e80000000
memory.region[0x1].base = 0x4000000000
.size = 0x2000000000
reserved.cnt = 0x5
reserved.size = 0x3e80000000
reserved.region[0x0].base = 0x0
.size = 0x7b5000
reserved.region[0x1].base = 0x2a00000
.size = 0x78c000
reserved.region[0x2].base = 0x328c000
.size = 0x43000
reserved.region[0x3].base = 0xf4e8000
.size = 0xb18000
reserved.region[0x4].base = 0x4000000000
.size = 0x2000000000
The reserved.region[0x4] contains the 16G pages. In
arch/powerpc/mm/num.c: do_init_bootmem() we loop through each of the
node numbers looking for the reserved regions that belong to the
particular node. It is not able to identify region 0x4 as being a part
of each of the 8 nodes. It is assuming that a reserved region is only
on a single node.
This patch takes out the reserved region loop from inside
the loop that goes over each node. It looks up the active region containing
the start of the reserved region. If it extends past that active region then
it adjusts the size and gets the next active region containing it.
Signed-off-by: Jon Tollefson <kniht@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 9b09c6d909 ("powerpc: Change the
default link address for pSeries zImage kernels") changed the
real-base value in the CHRP note added by the addnote program from
12MB to 32MB to give more space for Open Firmware to load the zImage.
(The real-base value says where we want OF to position itself in
memory.) However, this change was ineffective on most pSeries
machines, because the RPA note added by addnote has the "ignore me"
flag set to 1. This was intended to tell OF to ignore just the RPA
note, but has the side effect of also making OF ignore the CHRP note
(at least on most pSeries machines).
To solve this we have to set the "ignore me" flag to 0 in the RPA
note. (We can't just omit the RPA note because that is equivalent to
having an RPA note with default values, and the default values are not
what we want.) However, then we have to make sure the values in the
zImage's RPA note match up with the values that the kernel supplies
later in prom_init.c with either the ibm,client-architecture-support
call or the process-elf-header call in prom_send_capabilities().
So this sets the "ignore me" flag in the RPA note in addnote to 0, and
adjusts the RPA note values in addnote.c and in prom_init.c to be
consistent with each other and with the values in ibm_architecture_vec.
However, since the wrapper is independent of the kernel, this doesn't
ensure that the notes will stay consistent. To ensure that, this adds
code to addnote.c so that it can extract the kernel's RPA note from
the kernel binary and put that in the zImage. To that end, we put the
kernel's fake ELF header (which contains the kernel's RPA note) into
its own section, and arrange for wrapper to pull out that section with
objcopy and pass it to addnote, which then extracts the RPA note from
it and transfers it to the zImage.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc 32-bit and 64-bit kernel_thread functions don't properly
propagate errors being returned by the clone syscall. (In the case of
error, the syscall exit code returns a positive errno in r3 and sets
the CR0[SO] bit.)
This patch fixes that by negating r3 if CR0[SO] is set after the syscall.
Signed-off-by: Josh Poimboeuf <jpoimboe@us.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Offset is unsigned and when an address isn't found in the vma map
vma_map_lookup() returns the vma physical address + 0x10000000.
vma_map_lookup used to return 0xffffffff on a failed lookup, but
a change was made to return the vma physical address + 0x10000000
There are two callers of vam_map_lookup: one of them correctly
deals with this new return value, but the other (below) did not.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Maynard Johnson <maynardj@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Testing hotplug memory remove has revealed that we can oops in
pseries_lmb_remove(). The incorrect shift causes a NULL pointer
dereference in the page_zone() inline routine.
I have only been able to reproduce the oops on kernels with large pages
enabled.
Tested on Power5 and Power6 with and without large pages enabled.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A mutex_unlock(&gang->aff_mutex) in spufs_create_context() is missing
in case spufs_context_open() fails. As a result, spu_create syscall
and spu_get_idle() may block.
This patch adds the mutex_unlock.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Andre Detsch <adetsch@br.ibm.com>
Currently, an empty spufs root inode has nlink count of 1. However,
the directory has two links; / -> spu and /spu/ -> .
This change increments the link count of the root inode in spufs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Most ARM machines don't need a special "DMA" memory zone, and
when configured out, the kernel becomes a bit smaller:
| text data bss dec hex filename
|3826182 102384 111700 4040266 3da64a vmlinux
|3823593 101616 111700 4036909 3d992d vmlinux.nodmazone
This is because the system now has only one zone total which effect is
to optimize away many conditionals in page allocation paths.
So let's configure this zone only on machines that need split zones.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a cpu parameter to __cpufreq_driver_getavg(). This is needed for software
cpufreq coordination where policy->cpu may not be same as the CPU on which we
want to getavg frequency.
A follow-on patch will use this parameter to getavg freq from all cpus
in policy->cpus.
Change since last patch. Fix the offline/online and suspend/resume
oops reported by Youquan Song <youquan.song@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
add error handling for cpufreq_register_driver() error
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: cpufreq@lists.linux.org.uk
Signed-off-by: Dave Jones <davej@redhat.com>
1. arch/powerpc/platforms/pasemi/gpio_mdio.c also needs to be
converted over to mdiobus_{alloc,free}().
2. drivers/net/phy/fixed.c used to embed a struct mii_bus into its
struct fixed_mdio_bus and then use container_of() to go from the
former to the latter. Since mii bus structures are no longer
embedded, we need to do something like use the mii bus private
pointer to go from mii_bus to fixed_mdio_bus instead.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains Palm Zire 72 power
management support.
Depends on #5238/1
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
desc_handle_irq() was declared as obsolete since long ago.
Replace it with generic_handle_irq()
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When pinning/unpinning a pagetable with split pte locks, we can end up
holding multiple pte locks at once (we need to hold the locks while
there's a pending batched hypercall affecting the pte page). Because
all the pte locks are in the same lock class, lockdep thinks that
we're potentially taking a lock recursively.
This warning is spurious because we always take the pte locks while
holding mm->page_table_lock. lockdep now has spin_lock_nest_lock to
express this kind of dominant lock use, so use it here so that lockdep
knows what's going on.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move all the silicon rev handling to one place (Kconfig) and
make sure we warn if you are running on silicon that has not been tested on
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Fix two warnings when compiling for the KS8695 processor.
arch/arm/include/asm/dma-mapping.h: In function 'dma_to_virt':
arch/arm/include/asm/dma-mapping.h:40: warning: return makes pointer
from integer without a cast
Section mismatch in reference from the function pcibios_fixup_bus() to
the (unknown reference) .devinit.text:(unknown)
The function pcibios_fixup_bus() references
the (unknown reference) __devinit (unknown).
This is often because pcibios_fixup_bus lacks a __devinit
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace Macro names that have trailing underscores.
Also use the IOPD() macro instead of a hard-coded bit-shift (for
better readability).
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
avoid using actual config name in comment as a text search
is done to see what files need to be rebuilt
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
The kernel does not properly clear the EBIU Error Master (EBIU_ERRMST) Register
on BF548, which causes the kernel to panic.
We need to make sure that we clear the EBIU_ERRMST (necessary on BF54x)
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
a global _sys_trace will cause the assembler to fail, it should be fixed in toolchain side firstly.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Apply ANOMALY_05000283 & ANOMALY_05000315
Workaround also to the EXCEPTION path.
Cover evt_ivhw also with ANOMALY_05000315
The Workaround needs to be prior to accesses (either read or write) to
any system MMR.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
In preparation of giving mii_bus objects a device tree presence of
their own, rename struct mii_bus's ->dev argument to ->parent, since
having a 'struct device *dev' that points to our parent device
conflicts with introducing a 'struct device dev' representing our own
device.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch fixes EMAC soft reset on 460EX/GT when no external clock is
available.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Symbol name spaghetti which is too complicated to cleanup on this stage
of the release cycle breaks the build on BCM1480 platforms.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Explicitly cast resource fields to unsigned long long, and match format
specifier.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- one printk was missing a loglevel
- remove double space while we are here
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Include <linux/pm.h> to see the declaration of pm_power_off, and remove
unneeded NULL initializer.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
rename blackfin_sram.c to sram-alloc.c (we know it is a blackfin file,
since it is in arch/blackfin) - and there is no "driver" code in there,
it is just an allocator/deallocator for L1 and L2 sram.
Also fix a problem that checkpatch pointed out
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
use CONFIG_APP_STACKS_L1 to enable or disable putting kernel stacks in L1,
default is enabled, SMP kernel need turn it off
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Better error handling of unknown exceptions, allows userspace to do a
EXCPT n instruction for a not installed exception handler, and the
kernel doesn't crash (like it use to before this).
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Here is an updated version of a patch I wrote 6 years ago
http://marc.info/?l=linux-sparc&m=103939103607617&w=2
that simplifies interrupt mask lookup. It's main purpose
is to add VME bus support but it's really a cleanup of the mask code.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a processor implementation discern that a processor state component is in
its initialized state, it may modify the corresponding bit in the
xsave header.xstate_bv as '0'. State in the memory layout setup by 'xsave'
will be consistent with the bit values in the header.
During signal handling, legacy applications may change the FP/SSE bits
in the sigcontext memory layout without touching the FP/SSE header bits
in the xsave header. So always set FP/SSE bits in the xsave header
while saving the sigcontext state to the user space. During signal return,
this will enable the kernel to capture any changes to the FP/SSE bits by the
legacy applications which don't touch xsave headers.
xsave aware apps can change the xstate_bv in the xsave header aswell
as change any contents in the memory layout. xrestor as part of sigreturn
will capture all the changes.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This avoid the pre-mapping of OHCI controller register space, and the
mapping is made only when necessary (OHCI is probed).
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct access to pxa27x specific register PSSR in a generic ohci driver
is no good, introduce pxa27x_clear_otgph() and move the implementation
into processor specific code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct access to USB host controller registers is considered to be not
portable, and is usually a bad sign for poorly abstracted interface.
Introduce .flags and .power_on_delay to "struct pxaohci_platform_data"
so that most platforms don't bother to write their own .init/.exit()
sequences.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. DRCMRxx is no longer recommended, use DRCMR(xx) instead, and
pass DRCMR index by "struct resource" if possible
2. DCSRxx, DDADRxx, DSADRxx, DTADRxx, DCMDxx is never used, use
DCSR(), DDADR(), DSADR(), DTADR(), DCMD() instead
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The initialization of mfp sysdev in pxa2xx_mfp_init() shall really be
avoided when !cpu_is_pxa2xx().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for NOR and NAND flashes on CM-X255.
The NAND flash support uses not yet merged GPIO NAND driver.
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Change CM-X255 and CM-X270 common function prefix from cmx270 to cmx2xx
- Split cmx2xx_init to common and CM-X270-specific parts
- Use dynamic assignement for DM9000 resources and led GPIOs.
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds defines for the external chipselect physical base
addresses available with the EP93xx. These are meant to be used
in the platform init code.
In addition, documentation about the synchronous/asynchronous boot
modes for the EP93xx and a reference to errata about issues with
synchronous booting has been added.
Signed-off-by: <H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Disable IRQs while frobbing the CPLB registers, to avoid accessing the
data in current_rwx_mask while it isn't covered by CPLBs.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This PCI ID based quick should be a full solution for the IRQ0 override
related slowdown problem on SB450 based systems:
33fb0e4: x86: SB450: skip IRQ0 override if it is not routed to INT2 of IOAPIC
Emit a warning in those cases where the DMI quirk triggers but
the PCI ID based quirk didnt.
If this warning does not trigger then we can phase out the DMI quirks.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On some HP nx6... laptops (e.g. nx6325) BIOS reports an IRQ0 override
but the SB450 chipset is configured such that timer interrupts goe to
INT0 of IOAPIC.
Check IRQ0 routing and if it is routed to INT0 of IOAPIC skip the
timer override.
[ This more generic PCI ID based quirk should alleviate the need for
dmi_ignore_irq0_timer_override DMI quirks. ]
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: "Maciej W. Rozycki" <macro@linux-mips.org>
Tested-by: Dmitry Torokhov <dtor@mail.ru>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When manipulating 64-bit PCI addresses, the code would lose the
top 32-bit in a couple of places when shifting a pfn due to missing
type casting from the 32-bit pfn to a 64-bit resource before the
shift.
This breaks using newer X servers for example on 440 machines
with the PCI bus above 32-bit.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
rtas_log_read() doesn't check file flags for O_NONBLOCK and blocks
non-blocking readers of /proc/ppc64/rtas/error_log when there is
no data available. This fixes it.
Also rtas_log_read() returns now with ENODATA to prevent suspending of
process in wait_event_interruptible() when logging facility was
switched off and log is already empty.
Signed-off-by: Vitaly Mayatskikh <v.mayatskih@gmail.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix various defconfigs for Freescale chip based boards to remove
CONFIG_PPC_PMAC or CONFIG_PPC_CHRP which crept in due to those
being default y
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc uses CONFIG_FORCE_MAX_ZONEORDER, and some things depend on it
being at least 10 when 64k pages are not configured (notably the dart
iommu code with CONFIG_PM). The defaults are fine, but when going from a
64K pages config to one without 64K pages, MAX_ORDER stays at 9 which is
too low for 4K pages.
This patch makes the Kconfig enforce at least the defaults.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A bug in my initial 64-bit hibernation code breaks it when using
page sizes that aren't 4K.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 8b150478 ("ppc: make phys_mem_access_prot() work with pfns
instead of addresses") fixed page_is_ram() in arch/ppc to avoid overflow
for addresses above 4G on 32-bit kernels. However arch/powerpc's
page_is_ram() is missing the same fix -- it computes a physical address
by doing pfn << PAGE_SHIFT, which overflows if pfn corresponds to a page
above 4G.
In particular this causes pages above 4G to be mapped with the wrong
caching attribute; for example many ppc440-based SoCs have PCI space
above 4G, and mmap()ing MMIO space may end up with a mapping that has
caching enabled.
Fix this by working with the pfn and avoiding the conversion to
physical address that causes the overflow. This patch compares the
pfn to max_pfn, which is a semantic change from the old code -- that
code compared the physical address to high_memory, which corresponds
to max_low_pfn. However, I think that was is another bug, since
highmem pages are still RAM.
Reported-by: vb <vb@vsbe.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add a .gitignore in arch/powerpc/kernel to ignore the generated
vmlinux.lds.
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: gart iommu have direct mapping when agp is present too
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: workaround for bogus gcc warning in ide_sysfs_register_port()
ide-cd: Optiarc DVD RW AD-7200A does play audio
IDE: Fix platform device registration in Swarm IDE driver (v2)
ide-dma: fix ide_build_dmatable() for TRM290
ide-cd: temporary tray close fix
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] IP27: Fix build errors if CONFIG_MAPPED_KERNEL=y
[MIPS] Fix CMP Kconfig configuration and mark as broken.
Stress-testing KVM's latest NMI support with kgdbts inside an SMP guest,
I came across spurious unhandled NMIs while running the singlestep test.
Looking closer at the code path each NMI takes when KGDB is enabled, I
noticed that kgdb_nmicallback is called twice per event: One time via
DIE_NMI_IPI notification, the second time on DIE_NMI. Removing the first
invocation cures the unhandled NMIs here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
There is a bug in the BIOSes of some HP boxes with AMD Turions which
connects IO-APIC pins with ACPI thermal trip points in such a way that
if the state of the IO-APIC is not as expected by the (buggy) BIOS, the
thermal trip points are set to insanely low values (usually all of them
become 16 degrees Celsius). As a result, thermal throttling kicks in
and knock the system down to its shoes.
Unfortunately some of the recent IO-APIC changes made the bug show up.
To prevent this from happening, blacklist machines that are known to be
affected (nx6115 and 6715b in this particular case).
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11516 listed as
a regression from 2.6.26.
On my box it was caused by:
commit 691874fa96
Author: Maciej W. Rozycki <macro@linux-mips.org>
Date: Tue May 27 21:19:51 2008 +0100
x86: I/O APIC: timer through 8259A second-chance
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
and the whole story is described in this (huge) thread:
http://marc.info/?l=linux-kernel&m=121358440508410&w=4
Matthew Garrett told us about that happening on the nx6125:
http://marc.info/?l=linux-kernel&m=121396307411930&w=4
and then Maciej analysed the breakage on the basis of a DSDT from the
nx6325:
http://marc.info/?l=linux-kernel&m=121401068718826&w=4
As far as the Dmitry's and Jason's boxes are concerned, I recognized the
symptoms and asked them to verify that the blacklisting helped.
It appears that the buggy BIOS code has been copy-pasted to the entire
range of machines, for no good reason.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Jason Vas Dias <jason.vas.dias@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for DMA transfers through the generic DMA engine
framework with the DMA slave extensions.
The driver has been tested using mmc-block and ext3fs on several SD,
SDHC and MMC+ cards. Reads and writes work fine, with read transfer
rates up to 7.5 MiB/s on fast cards with debugging disabled.
Unfortunately, the driver has been known to lock up from time to time
with DMA enabled, so DMA support is currently optional and marked
EXPERIMENTAL. However, I didn't see any problems while testing 13
different cards (MMC, SD and SDHC of different brands and sizes), so I
suspect the "Initialize BLKR before sending data transfer command" fix
that was posted earlier fixed this as well.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
The Atmel MCI controller can drive multiple cards through separate sets
of pins, but only one at a time. This patch adds support for
multiplexing access to the controller so that multiple card slots can be
used as if they were hooked up to separate mmc controllers.
The atmel-mci driver registers each slot as a separate mmc_host. Both
access the same common controller state, but they also have some state
on their own for card detection/write protect handling, and separate
shadows of the MR and SDCR registers.
When one of the slots receives a request from the mmc core, the common
controller state is checked. If it's idle, the request is submitted
immediately. If not, the request is added to a queue. When a request is
done, the queue is checked and if there is a queued request, it is
submitted before the completion callback is called.
This patch also includes a few cleanups and fixes, including a locking
overhaul. I had to change the locking extensively in any case, so I
might as well try to get it right. The driver no longer takes any
irq-safe locks, which may or may not improve the overall system
performance.
This patch also adds a bit of documentation of the internal data
structures.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Add the necessary platform infrastructure to support multiple mmc/sdcard
slots all at once through a single controller. Currently, the driver
will use the first valid slot it finds and stick with that, but later
patches will add support for switching between several slots on the fly.
Extend the platform data structure with per-slot information: MMC/SDcard
bus width and card detect/write protect pins. This will affect the pin
muxing as well as the capabilities announced to the mmc core.
Note that board code is now required to supply a mci_platform_data
struct to at32_add_device_mci().
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
This replaces the at32_clock_list array with a linked list.
Clocks can now be registered (added) to the list.
Signed-off-by: Alex Raimondi <raimondi@miromico.ch>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Replace a magic number with a named constant in the VESA boot code.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
move init_memory_mapping() out of init_k8_gatt.
for: http://bugzilla.kernel.org/show_bug.cgi?id=11676
2.6.27-rc2 to rc8, apgart fails, iommu=soft works, regression
This is needed because we need to map the GART aperture even
if the GATT is not initialized.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For the purpose of MTRR canonicalization, treat WRPROT as UNCACHEABLE.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The first 1M is don't care when it comes to the variables MTRRs.
Cover it as WB as a heuristic approximation; this is generally what we
want to minimize the number of registers.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Print out the correct type when the Write Protected (WP) type is seen.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
After commit 968de4f ("i386: Relocatable kernel support") IMAGE_OFFSET wasn't
actually used anymore in the (current) X86 build system. Now remove its last
traces.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86 setup: correct segfault in generation of 32-bit reloc kernel
All EP93xx based systems can support Ethernet. This patch moves
the platform_device setup from the various board support files
into the core support file. The Ethernet driver data still remains
in the individual platform setup files to allow specific platform
configuration.
This also adds Ethernet support to the edb9302, edb9312, and
edb9315 platforms.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: segfault on build of a 32-bit relocatable kernel
When converting arch/x86/boot/compressed/relocs.c to support unlimited
sections, the computation of sym_strtab in walk_relocs() was done
incorrectly. This causes a segfault for some people when building the
relocatable 32-bit kernel.
Pointed out by Anonymous <pageexec@freemail.hu>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This fixes a regression that came with 934b2857cc
("[S390] nohz/sclp: disable timer on synchronous waits.").
If udelay() gets called from a disabled context it sets the clock comparator
to a value where it expects the next interrupt. When the interrupt happens
the clock comparator gets not reset and therefore the interrupt condition
doesn't get cleared. The result is an endless timer interrupt loop.
In addition this patch fixes also the following:
rcutorture reveals that our __udelay implementation is still buggy,
since it might schedule tasklets, but prevents their execution:
NOHZ: local_softirq_pending 42
NOHZ: local_softirq_pending 02
NOHZ: local_softirq_pending 142
NOHZ: local_softirq_pending 02
To fix this we make sure that only the clock comparator interrupt
is enabled when the enabled wait psw is loaded.
Also no code gets called anymore which might schedule tasklets.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Some BIOSes do not indicate error when trying to read from non-
existing device. Zero buffer before reading and check that we
possibly have valid MBR by looking for MBR magic.
This was fixed in different way for edd.S in
http://marc.info/?l=linux-kernel&m=114087765422490&w=2, but lost
again when edd.S was rewritten in C.
Signed-off-by: Andrey Borzenkov < arvidjaar@mail.ru>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Rework of SMTC support to make it work with the new clock event system,
allowing "tickless" operation, and to make it compatible with the use of
the "wait_irqoff" idle loop. The new clocking scheme means that the
previously optional IPI instant replay mechanism is now required, and has
been made more robust.
Signed-off-by: Kevin D. Kissell <kevink@paralogos.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Though from a hardware perspective it would be sensible to use only a
32-bit unsigned int type Linux defines interrupt flags to be stored in
an unsigned long and nothing else.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add fast_mode option to i2c_pxa_platform_data and use it to set the
ICR_FM bit appropriately when i2c_pxa_reset is called. Parameter
called fast_mode rather than frequency as this driver is also used
for the i2c_pxa_pwr bus which has different normal and fast frequencies.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These instructions were placed in the code directly as opcodes because
early compilers didn't support them. Toolchains supporting ARMv7
understand these instructions and the patch puts the mnemonics back.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently on the EP93xx platform early kernel messages go to UART1.
Since this UART is the only one that has modem control signals it
might be used for another purpose and it is undesirable for those
messages to appear. This patch allows one of the other UARTs to be
selected in the kernel configuration. It is assumed that the
bootloader has configured and initialized the UART since this was the
previous assumption.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
EXPORT sharpsl_param which is necessary to support modular build of some depending drivers.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[patch] x86: Trivial printk fix in efi.c
The following line is lacking a space between "memdesc" and "doesn't".
"Kernel-defined memdescdoesn't match the one from EFI!"
Fixed the printk by adding a space.
Signed-off-by: Russ Anderson <rja@sgi.com>
Cc: Russ Anderson <rja@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
remove braces and indent for flags and fpstate in restore_sigcontext().
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are a couple of Xen features which rely on directly accessing
per-cpu data via a segment register, which is not yet available on
x86-64. In the meantime, just disable direct access to the vcpu info
structure; this leaves some of the code as dead, but it will come to
life in time, and the warnings are suppressed.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds basic support for the Mobilepro
900/c mini-laptop. At present it won't do much
more than build and boot.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds generic battery driver for wm97xx chips.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no point converting memory bank addresses from physical to
virtual just to convert them back to physical addresses. Furthermore
this isn't "right" for highmem even if in this case the end result is
the correct one.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add a defconfig for the AMCC Arches evaluation board
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Arches Evaluation board is based on the AMCC 460GT SoC chip.
This board is a dual processor board with each processor providing
independent resources for Rapid IO, Gigabit Ethernet, and serial
communications. Each 460GT has it's own 512MB DDR2 memory, 32MB NOR FLASH,
UART, EEPROM and temperature sensor, along with a shared debug port.
The two 460GT's will communicate with each other via shared memory,
Gigabit Ethernet and x1 PCI-Express.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add support for the phy types found on the Arches and other
PowerPC 460 based boards.
Signed-off-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch allows the 4xx (conventional) PCI bridge to be disabled
via the device tree. This is needed for 4xx PCI adapter hardware.
Use the PCI node's status property to disable the PCI bridge.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Commit 00c5372d37 caused the MPC8544DS
board to hang at boot. The MPC8544DS is unique in that it doesn't use
the PCI slots on the ULI (unlike the MPC8572DS or MPC8610HPCD). So
the dummy read at the end of the address space causes us to hang.
We can detect the situation by comparing the bridge's BARs versus
the root complex.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the old led support in arch/arm/mach-pxa/leds...
for TRIZEPS4 SOM. It is / will be replaced by generic
led driver drivers/leds/...
Signed-off-by: Jürgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- use MFP-API for GPIO
- support TRIZEPS4WL module
- cleanups
Signed-off-by: Jrgen Schindele <linux@schindele.name>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes formatting issues in mach-sa1100/
machine files. More specificly badge4.c,generic.c and
pleb.c.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the jornada default
config (which was made for 2.6.12). Plenty
of development has happend since then, most
importantly the SSP driver and kbd/touchscr.
This config has been tested to compile
and bootup properly.
Signed-off-by: Kristoffer Ericson <Kristoffer.Ericson@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Enable Sparsemem support for LH7A40x SoCs, while still allowing the
existing discontig support for the time being.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the IRQ handling on the MN10300 arch.
This patch makes a number of significant changes:
(1) It separates the irq_chip definition for edge-triggered interrupts from
the one for level-triggered interrupts.
This is necessary because the MN10300 PIC latches the IRQ channel's
interrupt request bit (GxICR_REQUEST), even after the device has ceased to
assert its interrupt line and the interrupt channel has been disabled in
the PIC. So for level-triggered interrupts we need to clear this bit when
we re-enable - which is achieved by setting GxICR_DETECT but not
GxICR_REQUEST when writing to the register.
Not doing this results in spurious interrupts occurring because calling
mask_ack() at the start of handle_level_irq() is insufficient - it fails
to clear the REQUEST latch because the device that caused the interrupt is
still asserting its interrupt line at this point.
(2) IRQ disablement [irq_chip::disable_irq()] shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(3) IRQ unmasking [irq_chip::unmask_irq()] also shouldn't clear the interrupt
request flag for edge-triggered interrupts lest it lose an interrupt.
(4) The end() operation is now left to the default (no-operation) as
__do_IRQ() is compiled out. This may affect misrouted_irq(), but
according to Thomas Gleixner it's the correct thing to do.
(5) handle_level_irq() is used for edge-triggered interrupts rather than
handle_edge_irq() as the MN10300 PIC latches interrupt events even on
masked IRQ channels, thus rendering IRQ_PENDING unnecessary. It is
sufficient to call mask_ack() at the start and unmask() at the end.
(6) For level-triggered interrupts, ack() is now NULL as it's not used, and
there is no effective ACK function on the PIC. mask_ack() is now the
same as mask() as the latch continues to latch, even when the channel is
masked.
Further, the patch discards the disable() op implementation as its now the same
as the mask() op implementation, which is used instead.
It also discards the enable() op implementations as they're now the same as
the unmask() op implementations, which are used instead.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... including some comments about the ordering required to bring
sparsemem up. You have to repeatedly guess, test, reguess, try
again and again to work out what the right ordering is. Many
hours later...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide helpers for getting physical addresses or pfns from the
meminfo array, and use them. Move for_each_nodebank() to
asm/setup.h alongside the meminfo structure definition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for detecting non-executable stack binaries, and adjust
permissions to prevent execution from data and stack areas. Also,
ensure that READ_IMPLIES_EXEC is enabled for older CPUs where that
is true, and for any executable-stack binary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As of the previous commit, MT_DEVICE_IXP2000 encodes to the same
PTE bit encoding as MT_DEVICE, so it's now redundant. Convert
MT_DEVICE_IXP2000 to use MT_DEVICE instead, and remove its aliases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide L_PTE_MT_xxx definitions to describe the memory types that we
use in Linux/ARM. These definitions are carefully picked such that:
1. their LSBs match what is required for pre-ARMv6 CPUs.
2. they all have a unique encoding, including after modification
by build_mem_type_table() (the result being that some have more
than one combination.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are actually only four separate implementations of set_pte_ext.
Use assembler macros to insert code for these into the proc-*.S files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The math emulation code is centered around a set of generic macros that
provide the core of the emulation that are shared by the various
architectures and other projects (like glibc). Each arch implements its
own sfp-machine.h to specific various arch specific details.
For historic reasons that are now lost the powerpc math-emu code had
its own version of the common headers. This moves us to using the
kernel generic version and thus getting fixes when those are updated.
Also cleaned up exception/error reporting from the FP emulation functions.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
the below 2 functions are called in save_i387_xstate_ia32()
- clear_used_math();
- stts();
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
__put_user() looks type of the 2nd parameter, so casting the 1st parameter
is not necessary.
text data bss dec hex filename
6227 0 8 6235 185b ia32_signal.o.new
6227 0 8 6235 185b ia32_signal.o.old
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There's no point scattering this around the tree, the parsing
of the parameter might as well live beside the code which uses
it. That also means we can make vmalloc_reserve a static
variable.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The newly introduced sanity_check_meminfo() function should be
used to collect all validation of the meminfo array, which we
have in bootmem_init(). Move it there.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56
After investigating a JRE failure, I found this bug was introduced a long time
ago, and had already managed to survive another bugfix which occurred on the
same line. The result is a total failure of the JRE due to LDT selectors not
working properly.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After investigating a JRE failure, I found this bug was introduced a
long time ago, and had already managed to survive another bugfix which
occurred on the same line. The result is a total failure of the JRE due
to LDT selectors not working properly.
This one took a long time to rear up because LDT usage is not very
common, but the bug is quite serious. It got introduced along with
another bug, already fixed, by 75b8bb3e56
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Cc: <stable@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Make sure that coprocessor instructions for range ops are contiguous
and not reordered.
- s/invalidate_and_disable_dcache/flush_and_disable_dcache/
- Don't re-enable I/D caches if they were not enabled initially.
- Change some masks to shifts for better generated code.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
The PTRS_PER_PMD != 1 condition can be evaluated with C code and
optimized at compile time.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
