The maximum number of dirty pages that exist in the system at any time is
determined by a number of pages considered dirtyable and a user-configured
percentage of those, or an absolute number in bytes.
This number of dirtyable pages is the sum of memory provided by all the
zones in the system minus their lowmem reserves and high watermarks, so
that the system can retain a healthy number of free pages without having
to reclaim dirty pages.
But there is a flaw in that we have a zoned page allocator which does not
care about the global state but rather the state of individual memory
zones. And right now there is nothing that prevents one zone from filling
up with dirty pages while other zones are spared, which frequently leads
to situations where kswapd, in order to restore the watermark of free
pages, does indeed have to write pages from that zone's LRU list. This
can interfere so badly with IO from the flusher threads that major
filesystems (btrfs, xfs, ext4) mostly ignore write requests from reclaim
already, taking away the VM's only possibility to keep such a zone
balanced, aside from hoping the flushers will soon clean pages from that
zone.
Enter per-zone dirty limits. They are to a zone's dirtyable memory what
the global limit is to the global amount of dirtyable memory, and try to
make sure that no single zone receives more than its fair share of the
globally allowed dirty pages in the first place. As the number of pages
considered dirtyable excludes the zones' lowmem reserves and high
watermarks, the maximum number of dirty pages in a zone is such that the
zone can always be balanced without requiring page cleaning.
As this is a placement decision in the page allocator and pages are
dirtied only after the allocation, this patch allows allocators to pass
__GFP_WRITE when they know in advance that the page will be written to and
become dirty soon. The page allocator will then attempt to allocate from
the first zone of the zonelist - which on NUMA is determined by the task's
NUMA memory policy - that has not exceeded its dirty limit.
At first glance, it would appear that the diversion to lower zones can
increase pressure on them, but this is not the case. With a full high
zone, allocations will be diverted to lower zones eventually, so it is
more of a shift in timing of the lower zone allocations. Workloads that
previously could fit their dirty pages completely in the higher zone may
be forced to allocate from lower zones, but the amount of pages that
"spill over" are limited themselves by the lower zones' dirty constraints,
and thus unlikely to become a problem.
For now, the problem of unfair dirty page distribution remains for NUMA
configurations where the zones allowed for allocation are in sum not big
enough to trigger the global dirty limits, wake up the flusher threads and
remedy the situation. Because of this, an allocation that could not
succeed on any of the considered zones is allowed to ignore the dirty
limits before going into direct reclaim or even failing the allocation,
until a future patch changes the global dirty throttling and flusher
thread activation so that they take individual zone states into account.
Test results
15M DMA + 3246M DMA32 + 504 Normal = 3765M memory
40% dirty ratio
16G USB thumb drive
10 runs of dd if=/dev/zero of=disk/zeroes bs=32k count=$((10 << 15))
seconds nr_vmscan_write
(stddev) min| median| max
xfs
vanilla: 549.747( 3.492) 0.000| 0.000| 0.000
patched: 550.996( 3.802) 0.000| 0.000| 0.000
fuse-ntfs
vanilla: 1183.094(53.178) 54349.000| 59341.000| 65163.000
patched: 558.049(17.914) 0.000| 0.000| 43.000
btrfs
vanilla: 573.679(14.015) 156657.000| 460178.000| 606926.000
patched: 563.365(11.368) 0.000| 0.000| 1362.000
ext4
vanilla: 561.197(15.782) 0.000|2725438.000|4143837.000
patched: 568.806(17.496) 0.000| 0.000| 0.000
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Tested-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The next patch will introduce per-zone dirty limiting functions in
addition to the traditional global dirty limiting.
Rename determine_dirtyable_memory() to global_dirtyable_memory() before
adding the zone-specific version, and fix up its documentation.
Also, move the functions to determine the dirtyable memory and the
function to calculate the dirty limit based on that together so that their
relationship is more apparent and that they can be commented on as a
group.
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Mel Gorman <mel@suse.de>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Per-zone dirty limits try to distribute page cache pages allocated for
writing across zones in proportion to the individual zone sizes, to reduce
the likelihood of reclaim having to write back individual pages from the
LRU lists in order to make progress.
This patch:
The amount of dirtyable pages should not include the full number of free
pages: there is a number of reserved pages that the page allocator and
kswapd always try to keep free.
The closer (reclaimable pages - dirty pages) is to the number of reserved
pages, the more likely it becomes for reclaim to run into dirty pages:
+----------+ ---
| anon | |
+----------+ |
| | |
| | -- dirty limit new -- flusher new
| file | | |
| | | |
| | -- dirty limit old -- flusher old
| | |
+----------+ --- reclaim
| reserved |
+----------+
| kernel |
+----------+
This patch introduces a per-zone dirty reserve that takes both the lowmem
reserve as well as the high watermark of the zone into account, and a
global sum of those per-zone values that is subtracted from the global
amount of dirtyable pages. The lowmem reserve is unavailable to page
cache allocations and kswapd tries to keep the high watermark free. We
don't want to end up in a situation where reclaim has to clean pages in
order to balance zones.
Not treating reserved pages as dirtyable on a global level is only a
conceptual fix. In reality, dirty pages are not distributed equally
across zones and reclaim runs into dirty pages on a regular basis.
But it is important to get this right before tackling the problem on a
per-zone level, where the distance between reclaim and the dirty pages is
mostly much smaller in absolute numbers.
[akpm@linux-foundation.org: fix highmem build]
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Shaohua Li <shaohua.li@intel.com>
Cc: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tracing ring-buffer used this function briefly, but not anymore.
Make it local to the writeback code again.
Also, move the function so that no forward declaration needs to be
reintroduced.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move invalidate_bdev, block_sync_page into fs/block_dev.c. Export
kill_bdev as well, so brd doesn't have to open code it. Reduce
buffer_head.h requirement accordingly.
Removed a rather large comment from invalidate_bdev, as it looked a bit
obsolete to bother moving. The small comment replacing it says enough.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Add an upper limit to balanced_rate according to the below inequality.
This filters out some rare but huge singular points, which at least
enables more readable gnuplot figures.
When there are N dd dirtiers,
balanced_dirty_ratelimit = write_bw / N
So it holds that
balanced_dirty_ratelimit <= write_bw
The singular points originate from dirty_rate in the below formular:
balanced_dirty_ratelimit = task_ratelimit * write_bw / dirty_rate
where
dirty_rate = (number of page dirties in the past 200ms) / 200ms
In the extreme case, if all dd tasks suddenly get blocked on something
else and hence no pages are dirtied at all, dirty_rate will be 0 and
balanced_dirty_ratelimit will be inf. This could happen in reality.
Note that these huge singular points are not a real threat, since they
are _guaranteed_ to be filtered out by the
min(balanced_dirty_ratelimit, task_ratelimit)
line in bdi_update_dirty_ratelimit(). task_ratelimit is based on the
number of dirty pages, which will never _suddenly_ fly away like
balanced_dirty_ratelimit. So any weirdly large balanced_dirty_ratelimit
will be cut down to the level of task_ratelimit.
There won't be tiny singular points though, as long as the dirty pages
lie inside the dirty throttling region (above the freerun region).
Because there the dd tasks will be throttled by balanced_dirty_pages()
and won't be able to suddenly dirty much more pages than average.
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
This helps to reduce dirty throttling polls and hence CPU overheads.
bdi->dirty_exceeded typically only helps when suddenly starting 100+
dd's on a disk, in which case the dd's may need to poll
balance_dirty_pages() earlier than tsk->nr_dirtied_pause.
CC: Jan Kara <jack@suse.cz>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
The LKP tests see big 56% regression for the case fio_mmap_randwrite_64k.
Shaohua manages to root cause it to be the much smaller dirty pause times
and hence much more frequent invocations to the IO-less balance_dirty_pages().
Since fio_mmap_randwrite_64k effectively contains both reads and writes,
the more frequent pauses triggered more idling in the cfq IO scheduler.
The solution is to increase pause time all the way up to the max 200ms
in this case, which is found to restore most performance. This will help
reduce CPU overheads in other cases, too.
Note that I don't expect many performance critical workloads to run this
access pattern: the mmap read-on-write is rather inefficient and could
be avoided by doing normal writes syscalls.
CC: Jan Kara <jack@suse.cz>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Li Shaohua <shaohua.li@intel.com>
Tested-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Control the pause time and the call intervals to balance_dirty_pages()
with three parameters:
1) max_pause, limited by bdi_dirty and MAX_PAUSE
2) the target pause time, grows with the number of dd tasks
and is normally limited by max_pause/2
3) the minimal pause, set to half the target pause
and is used to skip short sleeps and accumulate them into bigger ones
The typical behaviors after patch:
- if ever task_ratelimit is far below dirty_ratelimit, the pause time
will remain constant at max_pause and nr_dirtied_pause will be
fluctuating with task_ratelimit
- in the normal cases, nr_dirtied_pause will remain stable (keep in the
same pace with dirty_ratelimit) and the pause time will be fluctuating
with task_ratelimit
In summary, someone has to fluctuate with task_ratelimit, because
task_ratelimit = nr_dirtied_pause / pause
We normally prefer a stable nr_dirtied_pause, until reaching max_pause.
The notable behavior changes are:
- in stable workloads, there will no longer be sudden big trajectory
switching of nr_dirtied_pause as concerned by Peter. It will be as
smooth as dirty_ratelimit and changing proportionally with it (as
always, assuming bdi bandwidth does not fluctuate across 2^N lines,
otherwise nr_dirtied_pause will show up in 2+ parallel trajectories)
- in the rare cases when something keeps task_ratelimit far below
dirty_ratelimit, the smoothness can no longer be retained and
nr_dirtied_pause will be "dancing" with task_ratelimit. This fixes a
(not that destructive but still not good) bug that
dirty_ratelimit gets brought down undesirably
<= balanced_dirty_ratelimit is under estimated
<= weakly executed task_ratelimit
<= pause goes too large and gets trimmed down to max_pause
<= nr_dirtied_pause (based on dirty_ratelimit) is set too large
<= dirty_ratelimit being much larger than task_ratelimit
- introduce min_pause to avoid small pause sleeps
- when pause is trimmed down to max_pause, try to compensate it at the
next pause time
The "refactor" type of changes are:
The max_pause equation is slightly transformed to make it slightly more
efficient.
We now scale target_pause by (N * 10ms) on 2^N concurrent tasks, which
is effectively equal to the original scaling max_pause by (N * 20ms)
because the original code does implicit target_pause ~= max_pause / 2.
Based on the same implicit ratio, target_pause starts with 10ms on 1 dd.
CC: Jan Kara <jack@suse.cz>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Compensate the task's think time when computing the final pause time,
so that ->dirty_ratelimit can be executed accurately.
think time := time spend outside of balance_dirty_pages()
In the rare case that the task slept longer than the 200ms period time
(result in negative pause time), the sleep time will be compensated in
the following periods, too, if it's less than 1 second.
Accumulated errors are carefully avoided as long as the max pause area
is not hitted.
Pseudo code:
period = pages_dirtied / task_ratelimit;
think = jiffies - dirty_paused_when;
pause = period - think;
1) normal case: period > think
pause = period - think
dirty_paused_when = jiffies + pause
nr_dirtied = 0
period time
|===============================>|
think time pause time
|===============>|==============>|
------|----------------|---------------|------------------------
dirty_paused_when jiffies
2) no pause case: period <= think
don't pause; reduce future pause time by:
dirty_paused_when += period
nr_dirtied = 0
period time
|===============================>|
think time
|===================================================>|
------|--------------------------------+-------------------|----
dirty_paused_when jiffies
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
De-account the accumulative dirty counters on page redirty.
Page redirties (very common in ext4) will introduce mismatch between
counters (a) and (b)
a) NR_DIRTIED, BDI_DIRTIED, tsk->nr_dirtied
b) NR_WRITTEN, BDI_WRITTEN
This will introduce systematic errors in balanced_rate and result in
dirty page position errors (ie. the dirty pages are no longer balanced
around the global/bdi setpoints).
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
When dd in 512bytes, generic_perform_write() calls
balance_dirty_pages_ratelimited() 8 times for the same page, but
obviously the page is only dirtied once.
Fix it by accounting tsk->nr_dirtied and bdp_ratelimits at page dirty time.
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
It's a years long problem that a large number of short-lived dirtiers
(eg. gcc instances in a fast kernel build) may starve long-run dirtiers
(eg. dd) as well as pushing the dirty pages to the global hard limit.
The solution is to charge the pages dirtied by the exited gcc to the
other random dirtying tasks. It sounds not perfect, however should
behave good enough in practice, seeing as that throttled tasks aren't
actually running so those that are running are more likely to pick it up
and get throttled, therefore promoting an equal spread.
Randy: fix compile error: 'dirty_throttle_leaks' undeclared in exit.c
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Some trace shows lots of bdi_dirty=0 lines where it's actually some
small value if w/o the accounting errors in the per-cpu bdi stats.
In this case the max pause time should really be set to the smallest
(non-zero) value to avoid IO queue underrun and improve throughput.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
On a system with 1 local mount and 1 NFS mount, if the NFS server
becomes not responding when dd to the NFS mount, the NFS dirty pages may
exceed the global dirty limit and _every_ task involving writing will be
blocked. The whole system appears unresponsive.
The workaround is to permit through the bdi's that only has a small
number of dirty pages. The number chosen (bdi_stat_error pages) is not
enough to enable the local disk to run in optimal throughput, however is
enough to make the system responsive on a broken NFS mount. The user can
then kill the dirtiers on the NFS mount and increase the global dirty
limit to bring up the local disk's throughput.
It risks allowing dirty pages to grow much larger than the global dirty
limit when there are 1000+ mounts, however that's very unlikely to happen,
especially in low memory profiles.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
We do "floating proportions" to let active devices to grow its target
share of dirty pages and stalled/inactive devices to decrease its target
share over time.
It works well except in the case of "an inactive disk suddenly goes
busy", where the initial target share may be too small. To mitigate
this, bdi_position_ratio() has the below line to raise a small
bdi_thresh when it's safe to do so, so that the disk be feed with enough
dirty pages for efficient IO and in turn fast rampup of bdi_thresh:
bdi_thresh = max(bdi_thresh, (limit - dirty) / 8);
balance_dirty_pages() normally does negative feedback control which
adjusts ratelimit to balance the bdi dirty pages around the target.
In some extreme cases when that is not enough, it will have to block
the tasks completely until the bdi dirty pages drop below bdi_thresh.
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
The sleep based balance_dirty_pages() can pause at most MAX_PAUSE=200ms
on every 1 4KB-page, which means it cannot throttle a task under
4KB/200ms=20KB/s. So when there are more than 512 dd writing to a
10MB/s USB stick, its bdi dirty pages could grow out of control.
Even if we can increase MAX_PAUSE, the minimal (task_ratelimit = 1)
means a limit of 4KB/s.
They can eventually be safeguarded by the global limit check
(nr_dirty < dirty_thresh). However if someone is also writing to an
HDD at the same time, it'll get poor HDD write performance.
We at least want to maintain good write performance for other devices
when one device is attacked by some "massive parallel" workload, or
suffers from slow write bandwidth, or somehow get stalled due to some
error condition (eg. NFS server not responding).
For a stalled device, we need to completely block its dirtiers, too,
before its bdi dirty pages grow all the way up to the global limit and
leave no space for the other functional devices.
So change the loop exit condition to
/*
* Always enforce global dirty limit; also enforce bdi dirty limit
* if the normal max_pause sleeps cannot keep things under control.
*/
if (nr_dirty < dirty_thresh &&
(bdi_dirty < bdi_thresh || bdi->dirty_ratelimit > 1))
break;
which can be further simplified to
if (task_ratelimit)
break;
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
There is no reason why task in balance_dirty_pages() shouldn't be killable
and it helps in recovering from some error conditions (like when filesystem
goes in error state and cannot accept writeback anymore but we still want to
kill processes using it to be able to unmount it).
There will be follow up patches to further abort the generic_perform_write()
and other filesystem write loops, to avoid large write + SIGKILL combination
exceeding the dirty limit and possibly strange OOM.
Reported-by: Kazuya Mio <k-mio@sx.jp.nec.com>
Tested-by: Kazuya Mio <k-mio@sx.jp.nec.com>
Reviewed-by: Neil Brown <neilb@suse.de>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
In balance_dirty_pages() task_ratelimit may be not initialized
(initialization skiped by goto pause), and then used when calling
tracing hook.
Fix it by moving the task_ratelimit assignment before goto pause.
Reported-by: Witold Baryluk <baryluk@smp.if.uj.edu.pl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'writeback-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Add a 'reason' to wb_writeback_work
writeback: send work item to queue_io, move_expired_inodes
writeback: trace event balance_dirty_pages
writeback: trace event bdi_dirty_ratelimit
writeback: fix ppc compile warnings on do_div(long long, unsigned long)
writeback: per-bdi background threshold
writeback: dirty position control - bdi reserve area
writeback: control dirty pause time
writeback: limit max dirty pause time
writeback: IO-less balance_dirty_pages()
writeback: per task dirty rate limit
writeback: stabilize bdi->dirty_ratelimit
writeback: dirty rate control
writeback: add bg_threshold parameter to __bdi_update_bandwidth()
writeback: dirty position control
writeback: account per-bdi accumulated dirtied pages
Looks like someone got distracted after adding the comment characters.
Signed-off-by: Johannes Weiner <jweiner@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The files changed within are only using the EXPORT_SYMBOL
macro variants. They are not using core modular infrastructure
and hence don't need module.h but only the export.h header.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This creates a new 'reason' field in a wb_writeback_work
structure, which unambiguously identifies who initiates
writeback activity. A 'wb_reason' enumeration has been
added to writeback.h, to enumerate the possible reasons.
The 'writeback_work_class' and tracepoint event class and
'writeback_queue_io' tracepoints are updated to include the
symbolic 'reason' in all trace events.
And the 'writeback_inodes_sbXXX' family of routines has had
a wb_stats parameter added to them, so callers can specify
why writeback is being started.
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Useful for analyzing the dynamics of the throttling algorithms and
debugging user reported problems.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Fix powerpc compile warnings
mm/page-writeback.c: In function 'bdi_position_ratio':
mm/page-writeback.c:622:3: warning: comparison of distinct pointer types lacks a cast [enabled by default]
page-writeback.c:635:4: warning: comparison of distinct pointer types lacks a cast [enabled by default]
Also fix gcc "uninitialized var" warnings.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Keep a minimal pool of dirty pages for each bdi, so that the disk IO
queues won't underrun. Also gently increase a small bdi_thresh to avoid
it stuck in 0 for some light dirtied bdi.
It's particularly useful for JBOD and small memory system.
It may result in (pos_ratio > 1) at the setpoint and push the dirty
pages high. This is more or less intended because the bdi is in the
danger of IO queue underflow.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
The dirty pause time shall ultimately be controlled by adjusting
nr_dirtied_pause, since there is relationship
pause = pages_dirtied / task_ratelimit
Assuming
pages_dirtied ~= nr_dirtied_pause
task_ratelimit ~= dirty_ratelimit
We get
nr_dirtied_pause ~= dirty_ratelimit * desired_pause
Here dirty_ratelimit is preferred over task_ratelimit because it's
more stable.
It's also important to limit possible large transitional errors:
- bw is changing quickly
- pages_dirtied << nr_dirtied_pause on entering dirty exceeded area
- pages_dirtied >> nr_dirtied_pause on btrfs (to be improved by a
separate fix, but still expect non-trivial errors)
So we end up using the above formula inside clamp_val().
The best test case for this code is to run 100 "dd bs=4M" tasks on
btrfs and check its pause time distribution.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Apply two policies to scale down the max pause time for
1) small number of concurrent dirtiers
2) small memory system (comparing to storage bandwidth)
MAX_PAUSE=200ms may only be suitable for high end servers with lots of
concurrent dirtiers, where the large pause time can reduce much overheads.
Otherwise, smaller pause time is desirable whenever possible, so as to
get good responsiveness and smooth user experiences. It's actually
required for good disk utilization in the case when all the dirty pages
can be synced to disk within MAX_PAUSE=200ms.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
As proposed by Chris, Dave and Jan, don't start foreground writeback IO
inside balance_dirty_pages(). Instead, simply let it idle sleep for some
time to throttle the dirtying task. In the mean while, kick off the
per-bdi flusher thread to do background writeback IO.
RATIONALS
=========
- disk seeks on concurrent writeback of multiple inodes (Dave Chinner)
If every thread doing writes and being throttled start foreground
writeback, it leads to N IO submitters from at least N different
inodes at the same time, end up with N different sets of IO being
issued with potentially zero locality to each other, resulting in
much lower elevator sort/merge efficiency and hence we seek the disk
all over the place to service the different sets of IO.
OTOH, if there is only one submission thread, it doesn't jump between
inodes in the same way when congestion clears - it keeps writing to
the same inode, resulting in large related chunks of sequential IOs
being issued to the disk. This is more efficient than the above
foreground writeback because the elevator works better and the disk
seeks less.
- lock contention and cache bouncing on concurrent IO submitters (Dave Chinner)
With this patchset, the fs_mark benchmark on a 12-drive software RAID0 goes
from CPU bound to IO bound, freeing "3-4 CPUs worth of spinlock contention".
* "CPU usage has dropped by ~55%", "it certainly appears that most of
the CPU time saving comes from the removal of contention on the
inode_wb_list_lock" (IMHO at least 10% comes from the reduction of
cacheline bouncing, because the new code is able to call much less
frequently into balance_dirty_pages() and hence access the global
page states)
* the user space "App overhead" is reduced by 20%, by avoiding the
cacheline pollution by the complex writeback code path
* "for a ~5% throughput reduction", "the number of write IOs have
dropped by ~25%", and the elapsed time reduced from 41:42.17 to
40:53.23.
* On a simple test of 100 dd, it reduces the CPU %system time from 30% to 3%,
and improves IO throughput from 38MB/s to 42MB/s.
- IO size too small for fast arrays and too large for slow USB sticks
The write_chunk used by current balance_dirty_pages() cannot be
directly set to some large value (eg. 128MB) for better IO efficiency.
Because it could lead to more than 1 second user perceivable stalls.
Even the current 4MB write size may be too large for slow USB sticks.
The fact that balance_dirty_pages() starts IO on itself couples the
IO size to wait time, which makes it hard to do suitable IO size while
keeping the wait time under control.
Now it's possible to increase writeback chunk size proportional to the
disk bandwidth. In a simple test of 50 dd's on XFS, 1-HDD, 3GB ram,
the larger writeback size dramatically reduces the seek count to 1/10
(far beyond my expectation) and improves the write throughput by 24%.
- long block time in balance_dirty_pages() hurts desktop responsiveness
Many of us may have the experience: it often takes a couple of seconds
or even long time to stop a heavy writing dd/cp/tar command with
Ctrl-C or "kill -9".
- IO pipeline broken by bumpy write() progress
There are a broad class of "loop {read(buf); write(buf);}" applications
whose read() pipeline will be under-utilized or even come to a stop if
the write()s have long latencies _or_ don't progress in a constant rate.
The current threshold based throttling inherently transfers the large
low level IO completion fluctuations to bumpy application write()s,
and further deteriorates with increasing number of dirtiers and/or bdi's.
For example, when doing 50 dd's + 1 remote rsync to an XFS partition,
the rsync progresses very bumpy in legacy kernel, and throughput is
improved by 67% by this patchset. (plus the larger write chunk size,
it will be 93% speedup).
The new rate based throttling can support 1000+ dd's with excellent
smoothness, low latency and low overheads.
For the above reasons, it's much better to do IO-less and low latency
pauses in balance_dirty_pages().
Jan Kara, Dave Chinner and me explored the scheme to let
balance_dirty_pages() wait for enough writeback IO completions to
safeguard the dirty limit. However it's found to have two problems:
- in large NUMA systems, the per-cpu counters may have big accounting
errors, leading to big throttle wait time and jitters.
- NFS may kill large amount of unstable pages with one single COMMIT.
Because NFS server serves COMMIT with expensive fsync() IOs, it is
desirable to delay and reduce the number of COMMITs. So it's not
likely to optimize away such kind of bursty IO completions, and the
resulted large (and tiny) stall times in IO completion based throttling.
So here is a pause time oriented approach, which tries to control the
pause time in each balance_dirty_pages() invocations, by controlling
the number of pages dirtied before calling balance_dirty_pages(), for
smooth and efficient dirty throttling:
- avoid useless (eg. zero pause time) balance_dirty_pages() calls
- avoid too small pause time (less than 4ms, which burns CPU power)
- avoid too large pause time (more than 200ms, which hurts responsiveness)
- avoid big fluctuations of pause times
It can control pause times at will. The default policy (in a followup
patch) will be to do ~10ms pauses in 1-dd case, and increase to ~100ms
in 1000-dd case.
BEHAVIOR CHANGE
===============
(1) dirty threshold
Users will notice that the applications will get throttled once crossing
the global (background + dirty)/2=15% threshold, and then balanced around
17.5%. Before patch, the behavior is to just throttle it at 20% dirtyable
memory in 1-dd case.
Since the task will be soft throttled earlier than before, it may be
perceived by end users as performance "slow down" if his application
happens to dirty more than 15% dirtyable memory.
(2) smoothness/responsiveness
Users will notice a more responsive system during heavy writeback.
"killall dd" will take effect instantly.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Add two fields to task_struct.
1) account dirtied pages in the individual tasks, for accuracy
2) per-task balance_dirty_pages() call intervals, for flexibility
The balance_dirty_pages() call interval (ie. nr_dirtied_pause) will
scale near-sqrt to the safety gap between dirty pages and threshold.
The main problem of per-task nr_dirtied is, if 1k+ tasks start dirtying
pages at exactly the same time, each task will be assigned a large
initial nr_dirtied_pause, so that the dirty threshold will be exceeded
long before each task reached its nr_dirtied_pause and hence call
balance_dirty_pages().
The solution is to watch for the number of pages dirtied on each CPU in
between the calls into balance_dirty_pages(). If it exceeds ratelimit_pages
(3% dirty threshold), force call balance_dirty_pages() for a chance to
set bdi->dirty_exceeded. In normal situations, this safeguarding
condition is not expected to trigger at all.
On the sqrt in dirty_poll_interval():
It will serve as an initial guess when dirty pages are still in the
freerun area.
When dirty pages are floating inside the dirty control scope [freerun,
limit], a followup patch will use some refined dirty poll interval to
get the desired pause time.
thresh-dirty (MB) sqrt
1 16
2 22
4 32
8 45
16 64
32 90
64 128
128 181
256 256
512 362
1024 512
The above table means, given 1MB (or 1GB) gap and the dd tasks polling
balance_dirty_pages() on every 16 (or 512) pages, the dirty limit won't
be exceeded as long as there are less than 16 (or 512) concurrent dd's.
So sqrt naturally leads to less overheads and more safe concurrent tasks
for large memory servers, which have large (thresh-freerun) gaps.
peter: keep the per-CPU ratelimit for safeguarding the 1k+ tasks case
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reviewed-by: Andrea Righi <andrea@betterlinux.com>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
There are some imperfections in balanced_dirty_ratelimit.
1) large fluctuations
The dirty_rate used for computing balanced_dirty_ratelimit is merely
averaged in the past 200ms (very small comparing to the 3s estimation
period for write_bw), which makes rather dispersed distribution of
balanced_dirty_ratelimit.
It's pretty hard to average out the singular points by increasing the
estimation period. Considering that the averaging technique will
introduce very undesirable time lags, I give it up totally. (btw, the 3s
write_bw averaging time lag is much more acceptable because its impact
is one-way and therefore won't lead to oscillations.)
The more practical way is filtering -- most singular
balanced_dirty_ratelimit points can be filtered out by remembering some
prev_balanced_rate and prev_prev_balanced_rate. However the more
reliable way is to guard balanced_dirty_ratelimit with task_ratelimit.
2) due to truncates and fs redirties, the (write_bw <=> dirty_rate)
match could become unbalanced, which may lead to large systematical
errors in balanced_dirty_ratelimit. The truncates, due to its possibly
bumpy nature, can hardly be compensated smoothly. So let's face it. When
some over-estimated balanced_dirty_ratelimit brings dirty_ratelimit
high, dirty pages will go higher than the setpoint. task_ratelimit will
in turn become lower than dirty_ratelimit. So if we consider both
balanced_dirty_ratelimit and task_ratelimit and update dirty_ratelimit
only when they are on the same side of dirty_ratelimit, the systematical
errors in balanced_dirty_ratelimit won't be able to bring
dirty_ratelimit far away.
The balanced_dirty_ratelimit estimation may also be inaccurate near
@limit or @freerun, however is less an issue.
3) since we ultimately want to
- keep the fluctuations of task ratelimit as small as possible
- keep the dirty pages around the setpoint as long time as possible
the update policy used for (2) also serves the above goals nicely:
if for some reason the dirty pages are high (task_ratelimit < dirty_ratelimit),
and dirty_ratelimit is low (dirty_ratelimit < balanced_dirty_ratelimit),
there is no point to bring up dirty_ratelimit in a hurry only to hurt
both the above two goals.
So, we make use of task_ratelimit to limit the update of dirty_ratelimit
in two ways:
1) avoid changing dirty rate when it's against the position control target
(the adjusted rate will slow down the progress of dirty pages going
back to setpoint).
2) limit the step size. task_ratelimit is changing values step by step,
leaving a consistent trace comparing to the randomly jumping
balanced_dirty_ratelimit. task_ratelimit also has the nice smaller
errors in stable state and typically larger errors when there are big
errors in rate. So it's a pretty good limiting factor for the step
size of dirty_ratelimit.
Note that bdi->dirty_ratelimit is always tracking balanced_dirty_ratelimit.
task_ratelimit is merely used as a limiting factor.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
It's all about bdi->dirty_ratelimit, which aims to be (write_bw / N)
when there are N dd tasks.
On write() syscall, use bdi->dirty_ratelimit
============================================
balance_dirty_pages(pages_dirtied)
{
task_ratelimit = bdi->dirty_ratelimit * bdi_position_ratio();
pause = pages_dirtied / task_ratelimit;
sleep(pause);
}
On every 200ms, update bdi->dirty_ratelimit
===========================================
bdi_update_dirty_ratelimit()
{
task_ratelimit = bdi->dirty_ratelimit * bdi_position_ratio();
balanced_dirty_ratelimit = task_ratelimit * write_bw / dirty_rate;
bdi->dirty_ratelimit = balanced_dirty_ratelimit
}
Estimation of balanced bdi->dirty_ratelimit
===========================================
balanced task_ratelimit
-----------------------
balance_dirty_pages() needs to throttle tasks dirtying pages such that
the total amount of dirty pages stays below the specified dirty limit in
order to avoid memory deadlocks. Furthermore we desire fairness in that
tasks get throttled proportionally to the amount of pages they dirty.
IOW we want to throttle tasks such that we match the dirty rate to the
writeout bandwidth, this yields a stable amount of dirty pages:
dirty_rate == write_bw (1)
The fairness requirement gives us:
task_ratelimit = balanced_dirty_ratelimit
== write_bw / N (2)
where N is the number of dd tasks. We don't know N beforehand, but
still can estimate balanced_dirty_ratelimit within 200ms.
Start by throttling each dd task at rate
task_ratelimit = task_ratelimit_0 (3)
(any non-zero initial value is OK)
After 200ms, we measured
dirty_rate = # of pages dirtied by all dd's / 200ms
write_bw = # of pages written to the disk / 200ms
For the aggressive dd dirtiers, the equality holds
dirty_rate == N * task_rate
== N * task_ratelimit_0 (4)
Or
task_ratelimit_0 == dirty_rate / N (5)
Now we conclude that the balanced task ratelimit can be estimated by
write_bw
balanced_dirty_ratelimit = task_ratelimit_0 * ---------- (6)
dirty_rate
Because with (4) and (5) we can get the desired equality (1):
write_bw
balanced_dirty_ratelimit == (dirty_rate / N) * ----------
dirty_rate
== write_bw / N
Then using the balanced task ratelimit we can compute task pause times like:
task_pause = task->nr_dirtied / task_ratelimit
task_ratelimit with position control
------------------------------------
However, while the above gives us means of matching the dirty rate to
the writeout bandwidth, it at best provides us with a stable dirty page
count (assuming a static system). In order to control the dirty page
count such that it is high enough to provide performance, but does not
exceed the specified limit we need another control.
The dirty position control works by extending (2) to
task_ratelimit = balanced_dirty_ratelimit * pos_ratio (7)
where pos_ratio is a negative feedback function that subjects to
1) f(setpoint) = 1.0
2) df/dx < 0
That is, if the dirty pages are ABOVE the setpoint, we throttle each
task a bit more HEAVY than balanced_dirty_ratelimit, so that the dirty
pages are created less fast than they are cleaned, thus DROP to the
setpoints (and the reverse).
Based on (7) and the assumption that both dirty_ratelimit and pos_ratio
remains CONSTANT for the past 200ms, we get
task_ratelimit_0 = balanced_dirty_ratelimit * pos_ratio (8)
Putting (8) into (6), we get the formula used in
bdi_update_dirty_ratelimit():
write_bw
balanced_dirty_ratelimit *= pos_ratio * ---------- (9)
dirty_rate
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
bdi_position_ratio() provides a scale factor to bdi->dirty_ratelimit, so
that the resulted task rate limit can drive the dirty pages back to the
global/bdi setpoints.
Old scheme is,
|
free run area | throttle area
----------------------------------------+---------------------------->
thresh^ dirty pages
New scheme is,
^ task rate limit
|
| *
| *
| *
|[free run] * [smooth throttled]
| *
| *
| *
..bdi->dirty_ratelimit..........*
| . *
| . *
| . *
| . *
| . *
+-------------------------------.-----------------------*------------>
setpoint^ limit^ dirty pages
The slope of the bdi control line should be
1) large enough to pull the dirty pages to setpoint reasonably fast
2) small enough to avoid big fluctuations in the resulted pos_ratio and
hence task ratelimit
Since the fluctuation range of the bdi dirty pages is typically observed
to be within 1-second worth of data, the bdi control line's slope is
selected to be a linear function of bdi write bandwidth, so that it can
adapt to slow/fast storage devices well.
Assume the bdi control line
pos_ratio = 1.0 + k * (dirty - bdi_setpoint)
where k is the negative slope.
If targeting for 12.5% fluctuation range in pos_ratio when dirty pages
are fluctuating in range
[bdi_setpoint - write_bw/2, bdi_setpoint + write_bw/2],
we get slope
k = - 1 / (8 * write_bw)
Let pos_ratio(x_intercept) = 0, we get the parameter used in code:
x_intercept = bdi_setpoint + 8 * write_bw
The global/bdi slopes are nicely complementing each other when the
system has only one major bdi (indicated by bdi_thresh ~= thresh):
1) slope of global control line => scaling to the control scope size
2) slope of main bdi control line => scaling to the writeout bandwidth
so that
- in memory tight systems, (1) becomes strong enough to squeeze dirty
pages inside the control scope
- in large memory systems where the "gravity" of (1) for pulling the
dirty pages to setpoint is too weak, (2) can back (1) up and drive
dirty pages to bdi_setpoint ~= setpoint reasonably fast.
Unfortunately in JBOD setups, the fluctuation range of bdi threshold
is related to memory size due to the interferences between disks. In
this case, the bdi slope will be weighted sum of write_bw and bdi_thresh.
Given equations
span = x_intercept - bdi_setpoint
k = df/dx = - 1 / span
and the extremum values
span = bdi_thresh
dx = bdi_thresh
we get
df = - dx / span = - 1.0
That means, when bdi_dirty deviates bdi_thresh up, pos_ratio and hence
task ratelimit will fluctuate by -100%.
peter: use 3rd order polynomial for the global control line
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Introduce the BDI_DIRTIED counter. It will be used for estimating the
bdi's dirty bandwidth.
CC: Jan Kara <jack@suse.cz>
CC: Michael Rubin <mrubin@google.com>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Revert the pass-good area introduced in ffd1f609ab ("writeback:
introduce max-pause and pass-good dirty limits") and make the max-pause
area smaller and safe.
This fixes ~30% performance regression in the ext3 data=writeback
fio_mmap_randwrite_64k/fio_mmap_randrw_64k test cases, where there are
12 JBOD disks, on each disk runs 8 concurrent tasks doing reads+writes.
Using deadline scheduler also has a regression, but not that big as CFQ,
so this suggests we have some write starvation.
The test logs show that
- the disks are sometimes under utilized
- global dirty pages sometimes rush high to the pass-good area for
several hundred seconds, while in the mean time some bdi dirty pages
drop to very low value (bdi_dirty << bdi_thresh). Then suddenly the
global dirty pages dropped under global dirty threshold and bdi_dirty
rush very high (for example, 2 times higher than bdi_thresh). During
which time balance_dirty_pages() is not called at all.
So the problems are
1) The random writes progress so slow that they break the assumption of
the max-pause logic that "8 pages per 200ms is typically more than
enough to curb heavy dirtiers".
2) The max-pause logic ignored task_bdi_thresh and thus opens the possibility
for some bdi's to over dirty pages, leading to (bdi_dirty >> bdi_thresh)
and then (bdi_thresh >> bdi_dirty) for others.
3) The higher max-pause/pass-good thresholds somehow leads to the bad
swing of dirty pages.
The fix is to allow the task to slightly dirty over task_bdi_thresh, but
no way to exceed bdi_dirty and/or global dirty_thresh.
Tests show that it fixed the JBOD regression completely (both behavior
and performance), while still being able to cut down large pause times
in balance_dirty_pages() for single-disk cases.
Reported-by: Li Shaohua <shaohua.li@intel.com>
Tested-by: Li Shaohua <shaohua.li@intel.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
NR_WRITTEN is now accounted at block IO enqueue time, which is not very
accurate as to common understanding. This moves NR_WRITTEN accounting to
the IO completion time and makes it more consistent with BDI_WRITTEN,
which is used for bandwidth estimation.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Michael Rubin <mrubin@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
radix_tree_tagged() is lockless - it reads from a member of the raid-tree
root node. It does not require any protection.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We set bdi->dirty_exceeded (and thus ratelimiting code starts to
call balance_dirty_pages() every 8 pages) when a per-bdi limit is
exceeded or global limit is exceeded. But per-bdi limit also depends
on the task. Thus different tasks reach the limit on that bdi at
different levels of dirty pages. The result is that with current code
bdi->dirty_exceeded ping-ponged between 1 and 0 depending on which task
just got into balance_dirty_pages().
We fix the issue by clearing bdi->dirty_exceeded only when per-bdi amount
of dirty pages drops below the threshold (7/8 * bdi_dirty_limit) where task
limits already do not have any influence.
Impact: The end result is, the dirty pages are kept more tightly under
control, with the average number slightly lowered than before. This
reduces the risk to throttle light dirtiers and hence more responsive.
However it may add overheads by enforcing balance_dirty_pages() calls
on every 8 pages when there are 2+ heavy dirtiers.
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Christoph Hellwig <hch@infradead.org>
CC: Dave Chinner <david@fromorbit.com>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Add trace event balance_dirty_state for showing the global dirty page
counts and thresholds at each global_dirty_limits() invocation. This
will cover the callers throttle_vm_writeout(), over_bground_thresh()
and each balance_dirty_pages() loop.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
The max-pause limit helps to keep the sleep time inside
balance_dirty_pages() within MAX_PAUSE=200ms. The 200ms max sleep means
per task rate limit of 8pages/200ms=160KB/s when dirty exceeded, which
normally is enough to stop dirtiers from continue pushing the dirty
pages high, unless there are a sufficient large number of slow dirtiers
(eg. 500 tasks doing 160KB/s will still sum up to 80MB/s, exceeding the
write bandwidth of a slow disk and hence accumulating more and more dirty
pages).
The pass-good limit helps to let go of the good bdi's in the presence of
a blocked bdi (ie. NFS server not responding) or slow USB disk which for
some reason build up a large number of initial dirty pages that refuse
to go away anytime soon.
For example, given two bdi's A and B and the initial state
bdi_thresh_A = dirty_thresh / 2
bdi_thresh_B = dirty_thresh / 2
bdi_dirty_A = dirty_thresh / 2
bdi_dirty_B = dirty_thresh / 2
Then A get blocked, after a dozen seconds
bdi_thresh_A = 0
bdi_thresh_B = dirty_thresh
bdi_dirty_A = dirty_thresh / 2
bdi_dirty_B = dirty_thresh / 2
The (bdi_dirty_B < bdi_thresh_B) test is now useless and the dirty pages
will be effectively throttled by condition (nr_dirty < dirty_thresh).
This has two problems:
(1) we lose the protections for light dirtiers
(2) balance_dirty_pages() effectively becomes IO-less because the
(bdi_nr_reclaimable > bdi_thresh) test won't be true. This is good
for IO, but balance_dirty_pages() loses an important way to break
out of the loop which leads to more spread out throttle delays.
DIRTY_PASSGOOD_AREA can eliminate the above issues. The only problem is,
DIRTY_PASSGOOD_AREA needs to be defined as 2 to fully cover the above
example while this patch uses the more conservative value 8 so as not to
surprise people with too many dirty pages than expected.
The max-pause limit won't noticeably impact the speed dirty pages are
knocked down when there is a sudden drop of global/bdi dirty thresholds.
Because the heavy dirties will be throttled below 160KB/s which is slow
enough. It does help to avoid long dirty throttle delays and especially
will make light dirtiers more responsive.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
The start of a heavy weight application (ie. KVM) may instantly knock
down determine_dirtyable_memory() if the swap is not enabled or full.
global_dirty_limits() and bdi_dirty_limit() will in turn get global/bdi
dirty thresholds that are _much_ lower than the global/bdi dirty pages.
balance_dirty_pages() will then heavily throttle all dirtiers including
the light ones, until the dirty pages drop below the new dirty thresholds.
During this _deep_ dirty-exceeded state, the system may appear rather
unresponsive to the users.
About "deep" dirty-exceeded: task_dirty_limit() assigns 1/8 lower dirty
threshold to heavy dirtiers than light ones, and the dirty pages will
be throttled around the heavy dirtiers' dirty threshold and reasonably
below the light dirtiers' dirty threshold. In this state, only the heavy
dirtiers will be throttled and the dirty pages are carefully controlled
to not exceed the light dirtiers' dirty threshold. However if the
threshold itself suddenly drops below the number of dirty pages, the
light dirtiers will get heavily throttled.
So introduce global_dirty_limit for tracking the global dirty threshold
with policies
- follow downwards slowly
- follow up in one shot
global_dirty_limit can effectively mask out the impact of sudden drop of
dirtyable memory. It will be used in the next patch for two new type of
dirty limits. Note that the new dirty limits are not going to avoid
throttling the light dirtiers, but could limit their sleep time to 200ms.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Introduce
nr_dirty = NR_FILE_DIRTY + NR_WRITEBACK + NR_UNSTABLE_NFS
in order to simplify many tests in the following patches.
balance_dirty_pages() will eventually care only about the dirty sums
besides nr_writeback.
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
The estimation value will start from 100MB/s and adapt to the real
bandwidth in seconds.
It tries to update the bandwidth only when disk is fully utilized.
Any inactive period of more than one second will be skipped.
The estimated bandwidth will be reflecting how fast the device can
writeout when _fully utilized_, and won't drop to 0 when it goes idle.
The value will remain constant at disk idle time. At busy write time, if
not considering fluctuations, it will also remain high unless be knocked
down by possible concurrent reads that compete for the disk time and
bandwidth with async writes.
The estimation is not done purely in the flusher because there is no
guarantee for write_cache_pages() to return timely to update bandwidth.
The bdi->avg_write_bandwidth smoothing is very effective for filtering
out sudden spikes, however may be a little biased in long term.
The overheads are low because the bdi bandwidth update only occurs at
200ms intervals.
The 200ms update interval is suitable, because it's not possible to get
the real bandwidth for the instance at all, due to large fluctuations.
The NFS commits can be as large as seconds worth of data. One XFS
completion may be as large as half second worth of data if we are going
to increase the write chunk to half second worth of data. In ext4,
fluctuations with time period of around 5 seconds is observed. And there
is another pattern of irregular periods of up to 20 seconds on SSD tests.
That's why we are not only doing the estimation at 200ms intervals, but
also averaging them over a period of 3 seconds and then go further to do
another level of smoothing in avg_write_bandwidth.
CC: Li Shaohua <shaohua.li@intel.com>
CC: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Introduce the BDI_WRITTEN counter. It will be used for estimating the
bdi's write bandwidth.
Peter Zijlstra <a.p.zijlstra@chello.nl>:
Move BDI_WRITTEN accounting into __bdi_writeout_inc().
This will cover and fix fuse, which only calls bdi_writeout_inc().
CC: Michael Rubin <mrubin@google.com>
Reviewed-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
