This patch adds a shutdown routine. It fixes a bug where when be2net
and be2iscsi are both used be2iscsi was not cleaning up its resources
properly causing be2net to fail to get loaded when the system is
rebooted.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix be2iscsi driver to use a separate pointer for each irq action->name
field and avoid display corruption in /proc/interrupts. The be2iscsi driver
was using a single static array in a function for the irq action->name field.
This results in garbage output from /proc/interrupts
The pointer for action->name is garbage and scribbles the output on the screen.
This patch fixes the problem:
156: 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 PCI-MSI-X beiscsi_msix_0017
This patch is based on Prarit's patch here:
http://www.spinics.net/lists/linux-scsi/msg52325.html
but I have fixed up the failure paths and removed
redundant check for !i suggested by Eike.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since active_mask is first assigned in an "else" block, the compiler throws
a warning saying that the active_mask variable may be used uninitialized in
a print statement later. Initialize active_mask to 0 in the declaration to
stop the warning.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Return sysfs error codes that match the conditions encountered.
This prevents sysfs from retrying a request which is conditioned
to fail under the current circumstance.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Provide bsg interface for updating VPD attached on the I2C serial bus.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Corrects the return value for the cases where read/write edc fails;
this prevents sysfs from retrying the operation until forever.
Corrects the printk width specifier for the first byte of buf.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver is not releasing the lock if ql2xdontresethba is set, this might lead
to a lockup.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Minidump allows us to catpure a snapshot of the firmware/hardware states at the
time of failure for further analysis.
[jejb: added missing #include <linux/vmalloc.h>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi_nopout task's TTT is defined as __be32 while the DMA
memory to the chip is CPU specific. This creates a problem for
unsolicited NOP-In responses where the TTT is not the RESERVED
tag of 0xFFs. This patch adds a call to be32_to_cpu for the TTT
specified.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In commit 6a716a8, while releasing the DDP context in case frame_send() failed,
the frame may already be freed, so we should store the pointer to fc_fcp_pkt and
release the DDP context using the locally stored fsp instead of getting fsp from
the fr_fsp(fp) on a frame.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Reported-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Call fc_block_scsi_eh() in all fcoe eh to blocks
the scsi_eh thread for blocked rports.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Current fc_eh_host_reset leaves lport offline
permanently due to FLOGI response getting
handled by LOGO response from last reset as both
had same exchange id.
So fix this by having end to end exches clean-up
using exchange abort along exches reset
done from fc_eh_host_reset. This would avoid
exchanges collision between the sessions across
the reset. In this case implicit login should have
done that but no aborting support for FIP
frames, so just wait till lport->r_a_tov before
restarting next flogi to ensure all exchanges
are good to use again for next session.
Below is the trace of LOGO from older session
coming ahead of FLOGI response with same exche id
0x203:-
617 86.435165 4e.00.0b -> ff.ff.fc FC ELS LOGO 0x203
618 86.435195 4e.00.0b -> b6.02.00 FC ELS LOGO 0x213
619 86.435220 4e.00.0b -> 18.03.00 FC ELS LOGO 0x223
620 86.435244 4e.00.0b -> 18.02.00 FC ELS LOGO 0x233
621 86.435267 4e.00.0b -> 18.01.00 FC ELS LOGO 0x243
622 86.435349 00.00.00 -> ff.ff.fe FC ELS FLOGI 0x203
623 86.435549 ff.ff.fc -> 4e.00.0b FC ELS ACC (LOGO) 0x203
624 86.438721 ff.ff.fe -> 4e.00.0b FC ELS ACC (FLOGI) 0x203
625 86.442059 18.03.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x223
626 86.443683 b6.02.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x213
627 86.447693 18.01.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x243
628 86.453499 18.02.00 -> 4e.00.0b FC ELS ACC (LOGO) 0x233
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Reviewed-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Increase it to NVRAM configured limit or 1024 whichever is less.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DIF/DIX support for zfcp is no longer experimental,
and config option is no longer necessary.
Return error from queuecommand for unsupported data directions.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The Marvell Universal Message Interface (UMI) defines a messaging
interface between host and Marvell products (Plato, for example). It
considers situations of limited system resource and optimized system
performance.
UMI driver translates host request to message and sends message
to FW via UMI, FW receives message and processes it, then sends response
to UMI driver.
FW generates an interrupt when it needs to send information or
response to UMI driver
Signed-off-by: Jianyun Li <jyli@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Export the name of iface session is attached to. This is needed
so tools like iscsiadm/iscsistart can match the sessions to
userspace ifaces when rebuilding iscsid's state during boot.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added new sysfs attr 'host_reset' in scsi_sysfs.c to
perform adapter or firmware reset as suggested by
Mike Christie here:
http://marc.info/?l=linux-scsi&m=127359347111167&w=2
user/application can write "adapter" or "firmware" on
this attr and it will call newly added function hook
in scsi_host_template to call LDD adapter or firmware
reset implementation.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This command is used to read ACB params from firmware
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This command will causes the firmware to update all
configurations to pre-defined factory default settings.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some CD-ROMs fail to report a media change correctly. The specific
one for this patch simply fails to respond to commands, then gives a
UNIT ATTENTION after being reset which returns ASC/ASCQ 28/00. This
is out of spec behaviour, but add a check in the eat CC/UA on reset
path to catch this case so the CD-ROM will function somewhat properly.
[jejb: fixed up white space and accepted without signoff]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hook qla4xxx in fw boot sysfs interface so iscsi tools
can use the info to create boot sessions.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1. Remove device database entry (ddb) state.
2. Remove device database (DDB) list building.
With open-iscsi integration the logins to the target devices are
handled by the user space. So the information of target is now
maintained in the iscsi_session object. This is handled at
libiscsi level so there is no need to maintain a list of DDBs in
the qla4xxx LLD.
3. qla4xxx: Remove add_device_dynamically.
Since autologin in FW is disabled with open-iscsi integration,
driver will never get an AEN for which driver has not requested
a DDB index. So remove the add_device_dynamically function.
4. Remove qla4xxx_tgt_dscvr
Since firmware autologin is disabled this function will not work.
Now user has the ability to do the target discovery and login to
each target individually. Firwmare will not do the login on its own.
5. Remove relogin related code
All relogin is handled by userspace now. qla4xxx just need to
notify userspace of a connection failure, this triggers the
relogin.
6. Remove add_session and alloc_session
Now qla4xxx uses iscsi_session_setup that would do the necessary
allocations for session and ddb_entry.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add scsi_transport_iscsi hooks in qla4xxx to support
iSCSI session management using iscsiadm.
This patch is based on discussion here
http://groups.google.com/group/open-iscsi/browse_thread/thread/e89fd888baf656a0#
Now users can use iscsiadm to do target discovery and do login/logout to
individual targets using the qla4xxx iSCSI class interface.
This patch leaves some dead code, but to make it easier to review
we are leaving and in the next patch we will remove that old code.
V2 - NOTE: Added code to avoid waiting for AEN during login/logout
in the driver, instead added a kernel to user event
to notify iscsid about login status. Because of this
iscsid will not get blocked.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Offload drivers like qla4xxx will offload the sending of the login/logout
pdus still, so this patch adds iscsi_conn_login_event which is
used by these types of drivers to notify userspace that the connection
has changed state.
It also adds a iscsi_is_session_online helper so the lld
can query the sessions state field.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds bsg support to qla4xxx.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds bsg support to the iscsi class. There is only
1 request, the host vendor one, supported. It is expected that
this would be used for things like flash updates.
This patch is made over this one
http://marc.info/?l=linux-scsi&m=131149780020992&w=2
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to set VLAN and show vlan settings in sysfs
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[Patch updated to new defines]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libiscsi does not support markers and if someone tries
to set them the driver does a BUG(). There is not need
to be that extreme. Just return -ENOSYS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to set vlan priority and enable/disble a vlan.
Patch based on code from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
iscsi_session_to_shost is a macro around dev_to_shost which returns a
Scsi_Host so there is no need to cast.
iscsi_session_to_shost is a macro around shost_priv which
returns a void pointer so no need to cast.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
We can replace the iface param mask with the
attr_is_visible callback.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's session attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and drivers to use the attribute container
sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A iscsi host can have multiple interfaces. This patch
adds a new iface iscsi class for this. It exports the
network settings now, and will be extended to also
export iscsi initiator port settings like the isid
and initiator name for drivers that can support multiple
initiator ports.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Move all ipaddress related param to "struct ipaddress_config"
from "struct scsi_qla_host"
- update function - qla4xxx_update_local_ip()
- Rename IPOPT_IPv4_PROTOCOL_ENABLE to IPOPT_IPV4_PROTOCOL_ENABLE
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
[update for new ISCSI_IFACE values]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patches from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allows user space (iscsiadm) to send down network configuration
parameters for LLD to set private network configuration on the iSCSI
adapters.
Based on patch from Lalit Chandivade.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During kdump testing I noticed timeouts when initialising each IPR
adapter. While the driver has logic to detect an adapter in an
indeterminate state, it wasn't triggering and each adapter went
through a 5 minute timeout before finally going operational.
Some analysis showed the needs_hard_reset flag wasn't getting set.
We can check the reset_devices kernel parameter which is set by
kdump and force a full reset. This fixes the problem.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: <stable@kernel.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
bnx2x driver would obtain the WWNN/WWPN from the shared memory and can be
obtained by the bnx2fc driver via ndo_fcoe_get_wwn.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Export fcoe_get_wwn, fcoe_validate_vport_create and fcoe_wwn_to_str so that all
LLDs can use these common function.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As an initiator, driver need not handle incoming ABTS. It initiates an ABTS if
any IO requests time out.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Free session resources before rport logoff
- Do not free session resources in bnx2fc_alloc_session_resc() as it is handled
in caller's error handling path.
- Do not call bnx2fc_free_session_resc() if bnx2fc_init_tgt() fails as cq_lock
is not yet initialized.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There exists a race condition between CQ doorbell unmap and IO completion path
that arms the CQ which causes a NULL dereference. Protect the ctx_base with
cq_lock to avoid this. Also, wait for the CQ doorbell to be successfully mapped
before arming the CQ.
Also, do not count uncolicited CQ completions for free_sqes.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During the unsolicited LOGO processing, the session is uploaded and offloaded
after the relogin is complete. In between any new IOs are errored back as the
upload completion flag is set. Upon exhausting the retry count, the application
fails the IOs. Return target busy for all the cases when session is not ready.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
CFC_DELETE is issued 2 secs after CONN_TERM is completed. If the session is
uploaded and offloaded immediately, it has to wait for the connection id to be
available.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since this flag was never cleared, the driver does not wait for firmware
destroy completions, causing missed KCQEs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since the driver holds the reference for vlan netdev, the reference has to be
released by the driver when the vlan device is removed. Driver handles this in
NETDEV_UNREGISTER event.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Move interface specific cleanup functionality to from bnx2fc_if_destroy to
bnx2fc_interface_cleanup. Do not access interface/hba in bnx2fc_if_destroy as
by the time this function is called interface may already be destroyed. This
patch is in preparation to handle NETDEV_UNREGISTER on a vlan device.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change them to bnx2fc_interface_setup/bnx2fc_interface_cleanup in preperation
for the patches to follow. Interface specific cleanup functionality will be
moved to bnx2fc_interface_cleanup.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When NPIV ports are created/deleted rapidly there is a race condition between
bnx2fc_vport_destroy() from sysfs and bnx2fc_flogi_resp(), which could try to
delete the NPIV port from the list twice. Fix is to loop through the list of
NPIV ports to find a match, and only when it exists remove it.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During sequence cleanup, an additional reference for an IO has been
taken. Because of this, the IO is never released into the free list.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Look up p->work_list to process cq completions, and correct the error check for
thread creation.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reset max receive frame size every time before attempting FLOGI. Without this,
the stale MFS value will be used.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
mpt2sas_base_detach() call was removed from _scsih_remove() while
doing some code shuffling. Mainly when we work on adding code for
scsih_shutdown(). I have added back mpt2sas_base_detach() which will
get callled from _scsih_remove().
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The memset of the fcp_cmnd struct needs to be moved so that it will not
zero-out valid data.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Transitioning to a LOOP_UPDATE loop-state could cause the driver
to miss normal link/target processing. LOOP_UPDATE is a crufty
artifact leftover from at time the driver performed it's own
internal command-queuing. Safely remove this state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Close a small window where we could falsely fail an abort request if the mailbox
command fails but the command was returned during interrupt context.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The dsd list shouldn't be manipulated without taking the per host hardware
lock to prevent multiple callers from trampling upon one another.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since we enable interrupts before initializing the firmware, use the chip
revision from PCI config space directly to perform the chip revision check.
Also remove the unnecessary firmware attributes test.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fix:
- Disables app tag peeking; correct tag check will be added when the
SCSI API is available.
- Always derive ref_tag from scsi_get_lba()
- Removes incorrect swap of FCP_LUN in FCP_CMND
- Moves app-tag error check before ref-tag check. The reason being,
currently there is no interface in SCSI to retrieve the app-tag
for protection I/Os, so driver puts zero for app-tag in the
firmware interface, but requests not to validate it, but when a
ref-tag error is detected by firmware, it would put
expected/actual tags for all the protection tags (guard/app/ref).
As driver checks for app tag error first, a ref-tag error is
incorrectly flagged as app-tag error.
- Convert HBA specific checks to capability based.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver needs to update protection bytes for uninitialized sectors as they are
not DMA-d.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Reviewed-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If a physical device exposed to the OS by hpsa
is replaced (e.g. one hot plug tape drive is replaced
by another, or a tape drive is placed into "OBDR" mode
in which it acts like a CD-ROM device) and a rescan is
initiated, the replaced device will be added to the
SCSI midlayer with target and lun numbers set to -1.
After that, a panic is likely to ensue. When a physical
device is replaced, the lun and target number should be
preserved.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The test to detect OBDR ("One Button Disaster Recovery")
cd-rom devices was comparing against uninitialized data.
Fixed by moving the test for the device to where the
inquiry data is collected, and uninitialized variable
altogether as it wasn't really being used.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: devel@open-fcoe.org
Cc: linux-scsi@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware only increments the put pointer on event types >= 4. Do not
increment the get pointer for event type 3.
Reported-by: Kapil Karkra <kapil.karkra@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hardware allows both an outstanding number commands and a timeout value
(whichever occurs first) as a gate to the next interrupt generation. This
scheme at completion time looks at the remaining number of outstanding tasks
and sets the timeout to maximize small transaction operation. If transactions
are large (take more than a few 10s of microseconds to complete) then
performance is not interrupt processing bound, so the small timeouts this
scheme generates are overridden by the time it takes for a completion to
arrive.
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of immediately completing any request that has a second
termination call made on it, wait for the TC done/abort HW event.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adding API update for adding isci_id entry scsi_host sysfs entry.
Also fixing up the sysfs registration to the scsi_host template
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Need the following workaround in the driver for interoperability with
the older Intel SSD drives and any other SATA drive that may exhibit the
same behavior. This is a corner case where SCU speed is limited to
either 3G or 1.5G and the drive has a period of DC idle when it switches
speed during SATA speed negotiation. Workaround :change PHYTOV[31:24]
from 0x36 to 0x3B.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The unsolicited frame control infrastructure requires a table of dma
addresses for the hardware to lookup the frame buffer location by an
index. The hardware expects the elements of this table to be 64-bit
quantities, so we cannot reference these elements as dma_addr_t. All
unsolicited frame protocols are affected, particularly SATA-PIO and SMP
which prevented direct-attached SATA drives and expander-attached drives
to not be discovered.
Cc: <stable@kernel.org>
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A bug (likely copy/paste) that has been carried from the original
implementation. The unsolicited frame handling structure returns the
d2h fis in the isci_request.stp.rsp buffer.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Moves the drivers for the Chelsio chipsets into
drivers/net/ethernet/chelsio/ and the necessary Kconfig and Makefile
changes.
CC: Divy Le Ray <divy@chelsio.com>
CC: Dimitris Michailidis <dm@chelsio.com>
CC: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the drivers for Broadcom devices into
drivers/net/ethernet/broadcom/ and the necessary Kconfig and Makefile
changes.
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Matt Carlson <mcarlson@broadcom.com>
CC: Gary Zambrano <zambrano@broadcom.com>
CC: "Maciej W. Rozycki" <macro@linux-mips.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (71 commits)
[SCSI] fcoe: cleanup cpu selection for incoming requests
[SCSI] fcoe: add fip retry to avoid missing critical keep alive
[SCSI] libfc: fix warn on in lport retry
[SCSI] libfc: Remove the reference to FCP packet from scsi_cmnd in case of error
[SCSI] libfc: cleanup sending SRR request
[SCSI] libfc: two minor changes in comments
[SCSI] libfc, fcoe: ignore rx frame with wrong xid info
[SCSI] libfc: release exchg cache
[SCSI] libfc: use FC_MAX_ERROR_CNT
[SCSI] fcoe: remove unused ptype field in fcoe_rcv_info
[SCSI] bnx2fc: Update copyright and bump version to 1.0.4
[SCSI] bnx2fc: Tx BDs cache in write tasks
[SCSI] bnx2fc: Do not arm CQ when there are no CQEs
[SCSI] bnx2fc: hold tgt lock when calling cmd_release
[SCSI] bnx2fc: Enable support for sequence level error recovery
[SCSI] bnx2fc: HSI changes for tape
[SCSI] bnx2fc: Handle REC_TOV error code from firmware
[SCSI] bnx2fc: REC/SRR link service request and response handling
[SCSI] bnx2fc: Support 'sequence cleanup' task
[SCSI] dh_rdac: Associate HBA and storage in rdac_controller to support partitions in storage
...
Cleanup to:
- have selection for all types of frames, not just FCP.
- remove redundant cpu_online check once fcoe_select_cpu called
as this is not required since later code flow check for offlined
cpu.
- Simplify fcoe_select_cpu() by removing unnecessary checks to
skip curr_cpu, this also fixes possibly infinite loop in case
of curr_cpu is the only cpu while iterating in the loop.
This cleanup mainly applies to target as incoming request are
mostly for target, therefore Kiran has verified the patch
with target also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use pending queue to retry FIP frame in case its tx
fails and use common pending queue for both fcoe
and fip frames using fcoe_port_send.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The lport retry timer hits warn on in case
it has become ready in response from fip
login from fcoe_ctlr_flogi_send(), this is
possible but safe code path, therefore
removing this warn on.
Jun 22 03:16:30 10.0.16.6 [488198.316517] host3: Assigned Port ID 180f02
Jun 22 03:16:32 10.0.16.6 [488200.091561] ------------[ cut here ]------------
Jun 22 03:16:32 10.0.16.6 [488200.091586] WARNING: at
drivers/scsi/libfc/fc_lport.c:1355 fc_lport_timeout+0xd9/0xe0 [libfc]()
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
fc_queuecommand() allocates an FCP packet for each SCSI command and sends
it out on the wire. In the process it stores the reference to the FCP packet
in the scsi_cmnd structure.
Now, in case under stress testing the libfc exchange layer runs out of
exchanges the fc_queuecommand() may not be able to send out commands out on
the wire. In such a scenario if there is an error in sending the FCP packet
out the wire; fc_queuecommand() deletes the FCP packet from internal queue,
releases the FCP packet and returns a SCSI_MLQUEUE_HOST_BUSY status to the
scsi-ml. But, the reference to the FCP packet set in the scsi_cmnd is not
removed from the scsi_cmnd in this code path.
This might lead to a crash under stress testing where the scsi_cmnd failed by
fc_queuecommand() comes up to fc_eh_abort() via scsi eh thread. fc_eh_abort()
will get reference to the FCP packet to be aborted from the scsi_cmnd for
further FCP abort related processing and then try to release the FCP packet
that has already been released.
This patch removes the FCP packet reference from the scsi_cmnd before returning
back from fc_queuecommand() in case of an error in sending out the FCP packet.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The variable on stack, namely cdb_op, is not used but removed.
[ Patch reworked by Robert Love due to invalid patch format ]
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
One change is to cleanup typo in comment for fc_fcp_recv(), another corrects
the misleading comment for fc_fcp_abts_resp().
[ Patch reworked by Robert Love due to invalid patch format ]
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Drop the rx frame having xid with wrong cpu info
or received with xid not matching to our xid.
Not dropping such frame is causing panic as
that causes accessing data struct beyond their
bounds.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If fail to create workqueue, the newly created cache for exchg has to be
released.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Reviewed-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Though defined, FC_MAX_ERROR_CNT is not used. It is used now for CRC error in
the path of receiving FCP frame.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is no need to cache the ptype in fcoe_rcv_info struct as it is never
used anywhere.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When there is a single BD for the entire data to be transmitted, use the BD
inside the SGL context and set the cached SGE indication in the task context
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver advertises its support for 'retry' bit and 'conf completion' bit in PRLI
params to enable support for 'sequence level error recovery'
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Program the firmware task structure with init_flags indicating the device is
'sequence level error recovery' capable.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driver decides to initiate REC on REC_TOV timer pop. The firmware maintains the
REC timer and informs the driver as a firmware error message, which is an
unsolicited event to the driver. Driver also issues REC on other unsolicited
events from firmware that indicate data loss.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For the devices that support sequence level error recovery, based on the REC
response, the firmware has to be informed about the offset from which the
retransmission should happen. Driver initiates sequence cleanup task to
firmware so that the firmware can program the task. Upon the sequence cleanup
completion, SRR is issued to retransmit the sequence.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
rdac hardware handler assumes that there is one-to-one relation ship
between the host and the controller w.r.t lun. IOW, it does not
support "multiple storage partitions" within a storage.
Example:
HBA1 and HBA2 see lun 0 and 1 in storage A (1)
HBA3 and HBA4 see lun 0 and 1 in storage A (2)
HBA5 and HBA6 see lun 0 and 1 in storage A (3)
luns 0 and 1 in (1), (2) and (3) are totally different.
But, rdac handler treats the lun 0s (and lun 1s) as the same when
sending a mode select to the controller, which is wrong.
This patch makes the rdac hardware handler associate HBA and the
storage w.r.t lun (and not the host itself).
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Convert to DIV_ROUND_UP_SECTOR_T usage for sectors / dev_max_sectors
kernel.h: Add DIV_ROUND_UP_ULL and DIV_ROUND_UP_SECTOR_T macro usage
iscsi-target: Add iSCSI fabric support for target v4.1
iscsi: Add Serial Number Arithmetic LT and GT into iscsi_proto.h
iscsi: Use struct scsi_lun in iscsi structs instead of u8[8]
iscsi: Resolve iscsi_proto.h naming conflicts with drivers/target/iscsi
The out_msi_disable label should be before cleanup_nomem to additionally
benefit from the call to iounmap. Subsequent gotos are adjusted to go to
out_msi_disable instead of cleanup_nomem, which now follows it. This is
safe because pci_disable_msi does nothing if pci_enable_msi was not called.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
expression e1,e2;
statement S;
@@
e1 = pci_ioremap_bar(...);
... when != e1 = e2
when != iounmap(e1)
when any
(
if (<+...e1...+>) S
|
if(...) { ... return 0; }
|
if (...) { ... when != iounmap(e1)
when != if (...) { ... iounmap(e1) ... }
* return ...;
} else S
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There's a code path in pmcraid that can be reached via device ioctl that
causes all sorts of ugliness, including heap corruption or triggering the
OOM killer due to consecutive allocation of large numbers of pages.
First, the user can call pmcraid_chr_ioctl(), with a type
PMCRAID_PASSTHROUGH_IOCTL. This calls through to
pmcraid_ioctl_passthrough(). Next, a pmcraid_passthrough_ioctl_buffer
is copied in, and the request_size variable is set to
buffer->ioarcb.data_transfer_length, which is an arbitrary 32-bit
signed value provided by the user. If a negative value is provided
here, bad things can happen. For example,
pmcraid_build_passthrough_ioadls() is called with this request_size,
which immediately calls pmcraid_alloc_sglist() with a negative size.
The resulting math on allocating a scatter list can result in an
overflow in the kzalloc() call (if num_elem is 0, the sglist will be
smaller than expected), or if num_elem is unexpectedly large the
subsequent loop will call alloc_pages() repeatedly, a high number of
pages will be allocated and the OOM killer might be invoked.
It looks like preventing this value from being negative in
pmcraid_ioctl_passthrough() would be sufficient.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If expander discovery fails (sas_discover_expander()), remove the
expander from the port device list (sas_ex_discover_expander()),
before freeing it. Else the list is corrupted and, e.g., when we
attempt to send SMP commands to other devices, the kernel oopses.
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Cc: stable@kernel.org
Reviewed-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on PRLI response, identify if the target is FCP-2 (seq level error
recovery) capable, and appropriately set the corresponding CONF, REC flags when
offloading the session.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently, bnx2fc has a hba structure that can work with only a single vlan
interface. When there is a change in vlan id, it does not have the capability
to switch to different vlan interface. To solve this problem, a new structure
called 'interface' has been introduced, and each hba can now have multiple
interfaces, one per vlan id.
Most of the patch is a moving the interface specific fields from hba to the
interface structure, and appropriately modifying the dereferences. A list of
interfaces (if_list) is maintained along with adapter list. During a create
call, the interface structure is allocated and added to if_list and deleted &
freed on a destroy call. Link events are propagated to all interfaces
belonging to the hba.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In a shared SAS setup, target devices may be reset by one of
several hosts, and outstanding commands on that device will be
completed to corresponding hosts with status of UNSOLICITED_ABORT.
Such commands should be retried instead of being treated as i/o
errors. Also fixed a nearby spelling error.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Most smartarrays tolerate it, but a few new ones don't.
Without this change some newer Smart Arrays will lock up
and i/o will grind to a halt.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change driver version to 8.3.25
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch implements a new FCF failover policy for the lpfc driver. It
allows the driver to choose which FCF to failover to based on the FCF
priority. This patch also introduces a new sysfs parameter
(fcf_failover_policy) to allow the user to choose which FCF failover policy
to use.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Enhancements to Debug infrastructure
- debugfs additions for new hardware.
- Correct stack overflow in lpfc_debugfs_dumpHBASlim_data()
- Correct warning on uninitialized reg_val in lpfc_idiag_drbacc_write()
- Separated the iDiag command for capturing mailbox commands for generic
issue mailbox command entry point and for BSG multi-buffer handling.
- Added capturing dumping capabiliy of mailbox command and external buffer
for the completion of the mailbox command so that the outcome can be
examined.
- Changed all the iDiag command structure data array indexing introduced so
far with properly defined macros.
- Added SLI4 device PCI BAR memory mapped register read/browse, write-by-
value, set-bit, and clear-bit methods for both interface type 0 and
interface type 2.
- Corrected warnings on mbxstatus being uninitialized in error paths in
lpfc_bsg.c
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
PCI and SR-IOV Fixes
- Call pci_save_state after the pci_restore_state completes.
- After calling pci_enable_pcie_error_reporting() and checking the return
value for logging messages from rc, reset rc to 0 to it will not later be
interpreted for error.
- Read PCI config space SR-IOV capability to get the number of VFs supported.
- Check for the PF's supported number of VFs before invoking PCI enable sriov
API call and log error message that user requested number of VFs is beyond
the PF capability if such request is passed in.
- Added check for Physical function with Virtual Functions attached. If so,
first disable all the VFs before proceeding to device reset.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fabric and Target Discovery Fixes
- Clear FC_VPORT_NEEDS_INIT_VPI flag during completion of REG_VFI mailbox
command.
- Prevent SLI3 Code from unregistering the physical VPI.
- Add an else clause to the code that checks and sets
sp->cmn.request_multiple_Nport to clear the bit.
- Remove a redundant mbox free.
- Modified lpfc_sli4_async_fip_evt to pass in physical VPI toi
lpfc_find_vport_by_vpid function.
- Modified lpfc_find_vport_by_vpid to translate physical VPI to logical VPI
before comparing with vport VPI.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adapter Interface fixes and changes
- Modify the macro field from lpfc_init_vpi_vpi to lpfc_init_vfi_vpi
- Add the new CQE_CODE_RECEIVE_V1 CQE Code, add code in the driver to handle
the new Code the same as the CQE_CODE_RECEIVE code except that there are
two new checks for this code that will cause the driver to use the new V1
macros for rq_id and fcf_id.
- Fix a bug in lpfc_prep_seq() where the size out of the first CQE was
ONLY being used, even though multiple dmabufs make up the sequence,
each have their own CQE with potentially different sizes.
- Fix bug in lpfc_bsg_ct_unsol_event() where the ulpContext and ulpWord[3]
fields of the XMIT_SEQUENCE64_CX IOCB were being calculated incorrectly.
- Do physical to logical translation before indexing into the active
XRI array.
- Populate physical vpi in the iocb data structure.
- Put the current accumulated total in each IOCB in the chain as we are
walking thru then. The last IOCB in the chain should have the total
length of the sequence.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellaneous Bug fixes and code cleanup
- Fix 16G link speed reporting by adding check for 16G check.
- Change the check and enforcement of MAILBOX_EXT_SIZE (2048B)
to the check and enforcement of BSG_MBOX_SIZE - sizeof(MAILBOX_t) (3840B).
- Instead of waiting for a fixed amount of time after performing firmware
reset, the driver shall wait for the Lancer SLIPORT_STATUS register for the
readiness of the firmware for bring up.
- Add logging to indicate when dynamic parameters are changed.
- Add revision and date to the firmware image format.
- Use revision instead of rev_name to check firmware image version.
- Update temporary offset after memcopy is complete for firmware update.
- Consolidated the use of the macros to get rid of duplicated register
offset definitions.
- Removed the unused second parameter in routine lpfc_bsg_diag_mode_enter()
- Enable debugfs when debugfs is enabled.
- Update function comments for lpfc_sli4_alloc_xri and lpfc_sli4_init_rpi_hdrs.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
T10 DIF Fixes
- Fix the case where the SCSI Host supplies the CRC and driver to controller
protection is on.
- Only support T10 DIF type 1. LBA always goes in ref tag and app tag is not
checked.
- Change the format of the sense data passed up to the SCSI layer to match the
Descriptor Format Sense Data found in SPC-4 sections 4.5.2.1 and 4.5.2.2.
- Fix Slip PDE implementation.
- Remove BUG() in else casein lpfc_sc_to_bg_opcodes.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to enable / disable lunmasking on Brocade adapter ports.
- Added support to query / clear lunmasking configuration.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to enable initiator based lun masking.
- Initiator based Lun masking works similar to zoning where
initiator port is allowed to see only those LUNs which are
configured to be seen.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added dconf (Driver Config) BFA sub-module.
- The dconf sub-module provides interfaces and manages flash writes
to the flash DRV parition.
- dconf sub-module also ensures that the whole 64K DRV partition is updated
on a flash write.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to configure QOS on Brocade adapter ports.
- Added support to collect / reset QOS statistics.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to collect and reset fcport stats.
- Modified design to allow multiple requests for fcport stats.
- fcport will remember the stats request in its stats_pending
queue and service each of the queued requests after receiving
a firmware response for the prior request.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to support IO profiling.
- Added support to configure and query IO profiling info.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Extended BSG to support stats, port log and trace reset and to support
adapter, port SET operations.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added logic to check the loopback test input speed based on port mode.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Made changes to always acknowledge RME interrupt and update
consumer index (CI) when RME interrupt is generated.
- Made changes to have ASIC specific hw_rspq_ack() handler.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Added support to post vendor unique events on fc_host.
- Supports adapter, port, ioc, flash and remote port based AEN events.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
rdac hardware handler uses "Subsystem Identifier" from C4 inquiry page
to uniquely identify a storage. The problem with that is that if any
any of the bytes are non-ascii, subsys_id will all be spaces (hex
0x20). This creates lot of problems especially when there are multiple
rdac storages are connected to the server.
Use "Storage Array Unique Identifier" from C8 inquiry page, which is the
world wide unique identifier for the storage array, to uniquely identify
the storage.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The code is changed to support the new dynamic logging infrastructure.
Following are the levels added.
Default is 0 - no logging. 0x40000000 - Module Init & Probe.
0x20000000 - Mailbox Cmnds. 0x10000000 - Device Discovery.
0x08000000 - IO tracing. 0x04000000 - DPC Thread.
0x02000000 - Async events. 0x01000000 - Timer routines.
0x00800000 - User space. 0x00400000 - Task Management.
0x00200000 - AER/EEH. 0x00100000 - Multi Q.
0x00080000 - P3P Specific. 0x00040000 - Virtual Port.
0x00020000 - Buffer Dump. 0x00010000 - Misc.
0x7fffffff - For enabling all logs, can be too many logs.
Setting ql2xextended_error_logging module parameter to any of the above
value, will enable the debug for that particular level.
Do LOGICAL OR of the value to enable more than one level.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds the dynamic logging framework to the qla2xxx driver.
The user will be able to change the logging levels on the fly i.e.
without load/unload of the driver. This also enables logging to be
enabled for a particular section of the driver such as initialization,
device discovery etc.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
During cable pull tests on our 16G FC adapter, we are seeing errors,
typically reads to close targets, which fail due to CRC or framing
errors caused by the cable being pull (return status DID_ERROR).
The adapter detects the error on one of the first frames received,
marks the FC exchange as dead (further frames go to bit bucket) and
signals the host of the error. This action is so quick, and coupled
with fast host CPUs, creates a scenario in which the midlayer sees
the failure and retries the io almost immediately. We've seen link
traces with the retry on the link while the original i/o is still
being processed by the target. We're also seeing the time window
for the "link to pull-apart" and the physical interface to report
disconnected to be in the few millisecond range. Which means, we're
encountering scenarios where the full retry count is exhausted
(all with error) by the midlayer before the link disconnect state
is detected.
We looked at 8G FC behavior and occasionally see the same behavior,
but as the link was slower, it rarely could exhaust all retries
before the link reported disconnect.
What is needed is a slight delay between io retries due to DID_ERROR
to cover this error. It is inappropriate to put this delay in the
driver, as the error is indistinguishable from other link-related errors,
nor does the driver track whether the io is a retry or not. This is also
easier than tracking between-io-error bursts that are seen in this
scenario.
The patch below updates the retry path so that it inserts a delay as
if the target was busy. The busy delay is on the order of 6ms. This
delay is sufficient to ensure the link down condition is reported
before the retry count is exhausted (at most 1 retry is seen).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Issue:
This issue is seen on LSI H/W WarpDrive SSS6200 When filed direct I/O
is tried as volume I/O the scmd field in internal lookup table get
cleared and because of that the retried volume I/O never gets reported
as completed to SML.
Result:
I/O timeout and Error handling thread will kicking off
Fix:
Setting back the scmd in the lookup table before retrying the failed
direct i/o
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Currently it's impossible to find out if the host supports
wide SCSI unless you're committed to trawl through syslog.
And it's near impossible to find the actual HBA id, which
is settable for some SCSI HBAs (like aic7xxx).
So export them via sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Ankit Jain <jankit@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support for interrupt tasklet, which will improve performance.
Correct spelling of "20011"
[jejb: simplified ifdefs and fixed unused variable problem]
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove obsolete comments and add new comments
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change code to match HBA datasheet.
Change code to make it readable.
Add support big endian for mvs_prd_imt.
Add cpu_to_le32 and cpu_to_le64 to use on addr.
Add scan_finished for structure mvs_prv_info.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add new macros: MVS_SOFT_RESET, MVS_HARD_RESET, MVS_PHY_TUNE,
MVS_COMMAND_ACTIVE, EXP_BRCT_CHG, MVS_MAX_SG
Add new member sg_width in struct mvs_chip_info
Use macros rather than magic number
Add new functions: mvs_fill_ssp_resp_iu, mvs_set_sense,
mvs_94xx_clear_srs_irq, mvs_94xx_phy_set_link_rate
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
This patch moves the iscsi_sna_lt() and iscsi_sna_lte(), along with
iscsi_sna_gt() and iscsi_sna_gte() from iscsi_target_mod into
static inlines inside of include/scsi/iscsi_proto.h
This patch also includes the ISCSI_HDR_LEN and ISCSI_CRC_LEN
definitions.
(Added JesperJ simpliciation for iscsi_sna_* usage)
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
struct scsi_lun is also just a struct with an array of 8 octets (64 bits)
but using it instead in iscsi structs lets us call scsilun_to_int
without a cast, and also lets us copy it using assignment, instead of
memcpy().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch renames the following iscsi_proto.h structures to avoid
namespace issues with drivers/target/iscsi/iscsi_target_core.h:
*) struct iscsi_cmd -> struct iscsi_scsi_req
*) struct iscsi_cmd_rsp -> struct iscsi_scsi_rsp
*) struct iscsi_login -> struct iscsi_login_req
This patch includes useful ISCSI_FLAG_LOGIN_[CURRENT,NEXT]_STAGE*,
and ISCSI_FLAG_SNACK_TYPE_* definitions used by iscsi_target_mod, and
fixes the incorrect definition of struct iscsi_snack to following
RFC-3720 Section 10.16. SNACK Request.
Also, this patch updates libiscsi, iSER, be2iscsi, and bn2xi to
use the updated structure definitions in a handful of locations.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (77 commits)
[SCSI] fix crash in scsi_dispatch_cmd()
[SCSI] sr: check_events() ignore GET_EVENT when TUR says otherwise
[SCSI] bnx2i: Fixed kernel panic due to illegal usage of sc->request->cpu
[SCSI] bfa: Update the driver version to 3.0.2.1
[SCSI] bfa: Driver and BSG enhancements.
[SCSI] bfa: Added support to query PHY.
[SCSI] bfa: Added HBA diagnostics support.
[SCSI] bfa: Added support for flash configuration
[SCSI] bfa: Added support to obtain SFP info.
[SCSI] bfa: Added support for CEE info and stats query.
[SCSI] bfa: Extend BSG interface.
[SCSI] bfa: FCS bug fixes.
[SCSI] bfa: DMA memory allocation enhancement.
[SCSI] bfa: Brocade-1860 Fabric Adapter vHBA support.
[SCSI] bfa: Brocade-1860 Fabric Adapter PLL init fixes.
[SCSI] bfa: Added Fabric Assigned Address(FAA) support
[SCSI] bfa: IOC bug fixes.
[SCSI] bfa: Enable ASIC block configuration and query.
[SCSI] bnx2i: Updated copyright and bump version
[SCSI] bnx2i: Modified to skip CNIC registration if iSCSI is not supported
...
Fix up some trivial conflicts in:
- drivers/scsi/bnx2fc/{bnx2fc.h,bnx2fc_fcoe.c}:
Crazy broadcom version number conflicts
- drivers/target/tcm_fc/tfc_cmd.c
Just trivial cleanups done on adjacent lines
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: Fix wrong check in list_splice_init_rcu()
net,rcu: Convert call_rcu(xt_rateest_free_rcu) to kfree_rcu()
sysctl,rcu: Convert call_rcu(free_head) to kfree
vmalloc,rcu: Convert call_rcu(rcu_free_vb) to kfree_rcu()
vmalloc,rcu: Convert call_rcu(rcu_free_va) to kfree_rcu()
ipc,rcu: Convert call_rcu(ipc_immediate_free) to kfree_rcu()
ipc,rcu: Convert call_rcu(free_un) to kfree_rcu()
security,rcu: Convert call_rcu(sel_netport_free) to kfree_rcu()
security,rcu: Convert call_rcu(sel_netnode_free) to kfree_rcu()
ia64,rcu: Convert call_rcu(sn_irq_info_free) to kfree_rcu()
block,rcu: Convert call_rcu(disk_free_ptbl_rcu_cb) to kfree_rcu()
scsi,rcu: Convert call_rcu(fc_rport_free_rcu) to kfree_rcu()
audit_tree,rcu: Convert call_rcu(__put_tree) to kfree_rcu()
security,rcu: Convert call_rcu(whitelist_item_free) to kfree_rcu()
md,rcu: Convert call_rcu(free_conf) to kfree_rcu()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
USB surprise removal of sr is triggering an oops in
scsi_dispatch_command(). What seems to be happening is that USB is
hanging on to a queue reference until the last close of the upper
device, so the crash is caused by surprise remove of a mounted CD
followed by attempted unmount.
The problem is that USB doesn't issue its final commands as part of
the SCSI teardown path, but on last close when the block queue is long
gone. The long term fix is probably to make sr do the teardown in the
same way as sd (so remove all the lower bits on ejection, but keep the
upper disk alive until last close of user space). However, the
current oops can be simply fixed by not allowing any commands to be
sent to a dead queue.
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some broken devices indicates that media has changed on every
GET_EVENT_STATUS_NOTIFICATION. This translates into MEDIA_CHANGE
uevent on every open() which lets udev run into a loop.
Verify GET_EVENT result against TUR and if it generates spurious
events for several times in a row, ignore the GET_EVENT events, and
trust only the TUR status.
This is the log of a USB stick with a (broken) fake CDROM drive:
scsi 5:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0 CCS
sd 5:0:0:0: Attached scsi generic sg3 type 0
scsi 5:0:0:1: CD-ROM SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0
sd 5:0:0:0: [sdb] Attached SCSI removable disk
sr2: scsi3-mmc drive: 48x/48x tray
sr 5:0:0:1: Attached scsi CD-ROM sr2
sr 5:0:0:1: Attached scsi generic sg4 type 5
sr2: GET_EVENT and TUR disagree continuously, suppress GET_EVENT events
sd 5:0:0:0: [sdb] 31777279 512-byte logical blocks: (16.2 GB/15.1 GiB)
sd 5:0:0:0: [sdb] No Caching mode page present
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sd 5:0:0:0: [sdb] No Caching mode page present
sd 5:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1
-tj: Updated to consider only spurious GET_EVENT events among
different types of disagreement and allow using TUR for kernel
event polling after GET_EVENT is ignored.
Reported-By: Markus Rathgeb maggu2810@googlemail.com
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@kernel.org # >= v2.6.38, fixes udev busy looping w/ certain devices
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A kernel panic was observed when passing the sc->request->cpu = -1 to
retrieve the per_cpu variable pointer:
#0 [ffff880011203960] machine_kexec at ffffffff81022bc3
#1 [ffff8800112039b0] crash_kexec at ffffffff81088630
#2 [ffff880011203a80] __die at ffffffff8139ea20
#3 [ffff880011203aa0] no_context at ffffffff8102f3a7
#4 [ffff880011203ae0] __bad_area_nosemaphore at ffffffff8102f665
#5 [ffff880011203ba0] retint_signal at ffffffff8139dd1f
#6 [ffff880011203cc8] bnx2i_indicate_kcqe at ffffffffa03dc4f2
#7 [ffff880011203da8] service_kcqes at ffffffffa03cb04f
#8 [ffff880011203e68] cnic_service_bnx2x_kcq at ffffffffa03cb14a
#9 [ffff880011203e88] cnic_service_bnx2x_bh at ffffffffa03cb1b3
The problem lies in the slow path sg_io (and perhaps sg_scsi_ioctl) call to
blk_get_request->get_request/wait->blk_alloc_request->blk_rq_init which
re-initializes the request->cpu to -1. There is no assignment for cpu from
that to the request_fn call to low level drivers.
When this happens, the sc->request->cpu will be using the init value of
-1. This will create a kernel panic when it hits bnx2i because the code
refers it to get the per_cpu variables ptr.
This change is to put in a guard against that and also for cases when
bio affinity/queue completion to the same cpu is not enabled. In those
cases, the request->cpu will remain a -1 also.
This bug was created from commit: b5cf6b63f7
For the case when the blk layer did not setup the request->cpu, bnx2i
will complete the sc with the current CPU of the thread.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The bnx2fc driver needs to handle netdev events on VLAN devices.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The rcu callback fc_rport_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(fc_rport_free_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
* pm-runtime:
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Runtime: Consistent utilization of deferred_resume
PM / Runtime: Prevent runtime_resume from racing with probe
PM / Runtime: Replace "run-time" with "runtime" in documentation
PM / Runtime: Improve documentation of enable, disable and barrier
PM: Limit race conditions between runtime PM and system sleep (v2)
PCI / PM: Detect early wakeup in pci_pm_prepare()
PM / Runtime: Return special error code if runtime PM is disabled
PM / Runtime: Update documentation of interactions with system sleep
The hard_reset parameter passed to the LLDD in the direct-attached
phy control case allows the LLDD to filter link failure events
while the direct-attached device reset is executing.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The messages emitted from task.c and some from request.c likely
duplicate (in a less undertandable way) what is reported by the
midlayer.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Perform checking per-pci device (even though all systems will only have
1 pci device in this generation), and delete support for silicon that
does not report a proper revision (i.e. A0).
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Most of these simple dereference macros are longer than their open coded
equivalent. Deleting enum sci_controller_mode is thrown in for good
measure.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jayamohan Kallickal