Fix following warning:
traps.h:23: extern's make no sense in userspace
Add an ifdef __KERNEL__ block that cover the
extern definition and a few related things that neither
is for userspace.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warnings in byteorder.h:
byteorder.h:4: include of <linux/types.h> is preferred over <asm/types.h>
byteorder.h:9: leaks CONFIG_SPARC32 to userspace where it is not valid
byteorder.h:13: leaks CONFIG_SPARC64 to userspace where it is not valid
byteorder.h:14: found __[us]{8,16,32,64} type without #include <linux/types.h>
byteorder.h:47: leaks CONFIG_SPARC64 to userspace where it is not valid
- changed to use include <linux/types.h> as suggested
- use preprocessor defined symbols to distingush between 32 and 64 bit
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warnings in jsflash.h:
jsflash.h:11: include of <linux/types.h> is preferred over <asm/types.h>
jsflash.h:24: found __[us]{8,16,32,64} type without #include <linux/types.h>
Fixed by changing the include to <linux/types.h>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the preparational steps the unification was simple.
The linux_prom_pci_registers definition did not look like
it could be unified at first look since the structure is assigned
using prop_getproperty() / of_get_property() so the structure
is assumed to come direct form the prom.
The LINUX_OPPROM_MAGIC was kept even if it is not used by the kernel
on the assumption that userspace may require it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the sparc and sparc64 versions so differences are minimal.
A few data types are changed to better reflect there actual usage.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like leftovers from the removal of the special ebus layer.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial unification where the sparc64 specific
parts are protected using a signle ifdef/endif pair.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two ptrace.h implementations are very alike but
the small differences required two set of ifdef/else/endif pairs.
The definition of reg_window32 could have been shared but
that would have required several updates in sparc32 code as
all printk formatting for example assume it is longs.
sparc_stackf looked like anohter candidate to share if the 32
bit was renamed to sparc_stackf32.
But it contains two pointers in the sparc32 version which would
have been 64 bit in the sparc64 version so it was non-trivial.
Using a set of accessor macros could do the trick if pursued later.
The sparc64 specific definitions are not protected by
ifdef - as it should not be required to do so.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the renamed types in place the unification was straightforward.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renaming a few types to contain a 32 suffix makes the
type names compatible with sparc64 and thus makes sharing
between the two a lot easier.
Note: None of these definitions are expected part of the
stable ABI towards userspace.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
They were almost identical and with the preapration
patch nothing was needed to be added.
The unified version contains a few sparc64 only definitions
but they are kept as is and not protected by ifdef/endif.
The unified version exports a bit more to userspace then the
32 bit version did.
This is not considered fatal.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o add a sparc32 only definition
o fix a few style issues (white space errors etc).
o include compiler.h (for __user)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To my suprise struct stat64 was not equal on sparc 32 and sparc64,
so there was really nothing to share here.
Unify the files by adding their respective content to stat.h.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sparc32 does not define __ARCH_WANT_OLD_STAT so
we do not use this structure neither do we support it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The posix types differed so much in their definition
that they are kept in separate blocks.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to define a config symbol if
it is never set to any value. Undefined symbols equal
to 'n'.
GENERIC_GPIO looks like it is similar but
it is set using select in some other file so
it must be kept.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next:
kbuild: ignore a few files in headers_check
kbuild: add checks for include of linux/types in userspace headers
kbuild: drop debugging leftover in tags.sh
kbuild: document environment variables
kbuild: make *config usage docs
kbuild: disable sparse warning "returning void-valued expression"
kbuild: in headers_install autoconvert asm/inline/volatile to __xxx__
kbuild: check for leaked CONFIG_ symbols to userspace
headers_check.pl: disallow extern's
kconfig: improve error messages for bad source statements
kconfig: struct property commented
kconfig: add comments to symbol flags
kconfig: explain symbol value defaults
m68k: fix recursive dependency in Kconfig
Impact: cleanup, reduce kernel size a bit
The current kernel build warns:
WARNING: vmlinux.o(.text+0x11458): Section mismatch in reference from the function swiotlb_alloc_boot() to the function .init.text:__alloc_bootmem_low()
The function swiotlb_alloc_boot() references
the function __init __alloc_bootmem_low().
This is often because swiotlb_alloc_boot lacks a __init
annotation or the annotation of __alloc_bootmem_low is wrong.
WARNING: vmlinux.o(.text+0x1011f2): Section mismatch in reference from the function swiotlb_late_init_with_default_size() to the function .init.text:__alloc_bootmem_low()
The function swiotlb_late_init_with_default_size() references
the function __init __alloc_bootmem_low().
This is often because swiotlb_late_init_with_default_size lacks a __init
annotation or the annotation of __alloc_bootmem_low is wrong.
and indeed the functions calling __alloc_bootmem_low() can be marked
__init as well.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
We had a recursive dependency between MMU_MOTOROLA and MMU_SUN3
Fix it by dropping the unused dependencies on MMU_MOTOROLA.
MMU_MOTOROLA is set to y only using select so any dependencies
are anyway ignored.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
* 'kvm-updates/2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (140 commits)
KVM: MMU: handle large host sptes on invlpg/resync
KVM: Add locking to virtual i8259 interrupt controller
KVM: MMU: Don't treat a global pte as such if cr4.pge is cleared
MAINTAINERS: Maintainership changes for kvm/ia64
KVM: ia64: Fix kvm_arch_vcpu_ioctl_[gs]et_regs()
KVM: x86: Rework user space NMI injection as KVM_CAP_USER_NMI
KVM: VMX: Fix pending NMI-vs.-IRQ race for user space irqchip
KVM: fix handling of ACK from shared guest IRQ
KVM: MMU: check for present pdptr shadow page in walk_shadow
KVM: Consolidate userspace memory capability reporting into common code
KVM: Advertise the bug in memory region destruction as fixed
KVM: use cpumask_var_t for cpus_hardware_enabled
KVM: use modern cpumask primitives, no cpumask_t on stack
KVM: Extract core of kvm_flush_remote_tlbs/kvm_reload_remote_mmus
KVM: set owner of cpu and vm file operations
anon_inodes: use fops->owner for module refcount
x86: KVM guest: kvm_get_tsc_khz: return khz, not lpj
KVM: MMU: prepopulate the shadow on invlpg
KVM: MMU: skip global pgtables on sync due to cr3 switch
KVM: MMU: collapse remote TLB flushes on root sync
...
Impact: cleanup, fix style problems, more readable
Fixes style problems:
WARNING: Use #include <linux/smp.h> instead of <asm/smp.h>
WARNING: Use #include <linux/acpi.h> instead of <asm/acpi.h>
WARNING: suspect code indent for conditional statements (8, 17)
WARNING: space prohibited between function name and open parenthesis '('
total: 0 errors, 5 warnings
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix crash on x86/UV
UV is the SGI "UltraViolet" machine, which is x86_64 based.
BAU is the "Broadcast Assist Unit", used for TLB shootdown in UV.
This patch removes the allocation and initialization of an unused table.
This table is left over from a development test mode. It is unused in
the present code.
And it was incorrectly initialized: 8 entries allocated but 17 initialized,
causing slab corruption.
This patch should go into 2.6.27 and 2.6.28 as well as the current tree.
Diffed against 2.6.28 (linux-next, 12/30/08)
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The pda rework (commit 3461b0af02)
to remove static boot cpu pdas introduced a performance bug.
_boot_cpu_pda is the actual pda used by the boot cpu and is definitely
not "__read_mostly" and ended up polluting the read mostly section with
writes. This bug caused regression of about 8-10% on certain syscall
intensive workloads.
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Acked-by: Mike Travis <travis@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
This compiler warning:
arch/x86/mm/init_32.c:515: warning: unused variable 'pgd_base'
triggers because permanent_kmaps_init() is a CPP macro in the
!CONFIG_HIGHMEM case, that does not tell the compiler that the
'pgd_base' parameter is used.
Convert permanent_kmaps_init() (and set_highmem_pages_init()) to
C inline functions - which gives the parameter a proper type and
which gets rid of the compiler warning as well.
Signed-off-by: Ingo Brueckl <ib@wupperonline.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (34 commits)
nfsd race fixes: jfs
nfsd race fixes: reiserfs
nfsd race fixes: ext4
nfsd race fixes: ext3
nfsd race fixes: ext2
nfsd/create race fixes, infrastructure
filesystem notification: create fs/notify to contain all fs notification
fs/block_dev.c: __read_mostly improvement and sb_is_blkdev_sb utilization
kill ->dir_notify()
filp_cachep can be static in fs/file_table.c
fix f_count description in Documentation/filesystems/files.txt
make INIT_FS use the __RW_LOCK_UNLOCKED initialization
take init_fs to saner place
kill vfs_permission
pass a struct path * to may_open
kill walk_init_root
remove incorrect comment in inode_permission
expand some comments (d_path / seq_path)
correct wrong function name of d_put in kernel document and source comment
fix switch_names() breakage in short-to-short case
...
Impact: Reduce stack usage, use new cpumask API. ALPHA mod!
Main change is that irq_default_affinity becomes a cpumask_var_t, so
treat it as a pointer (this effects alpha).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Impact: New API
The old topology_core_siblings() and topology_thread_siblings() return
a cpumask_t; these new ones return a (const) struct cpumask *.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: New API
The old topology_core_siblings() and topology_thread_siblings() return
a cpumask_t; these new ones return a (const) struct cpumask *.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: New API
The old topology_core_siblings() and topology_thread_siblings() return
a cpumask_t; these new ones return a (const) struct cpumask *.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Impact: New API
The old topology_core_siblings() and topology_thread_siblings() return
a cpumask_t; these new ones return a (const) struct cpumask *.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Like fls, but can't be handed 0 and returns the bit number.
(I broke this arch in linux-next by using __fls in generic code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Like fls, but can't be handed 0 and returns the bit number.
(I broke this arch in linux-next by using __fls in generic code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Like fls, but can't be handed 0 and returns the bit number.
(I broke this arch in linux-next by using __fls in generic code).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This is defined in linux/cpumask.h (included in this file already),
and this is now defined differently.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: linux-parisc@vger.kernel.org
Impact: CPU iterator bugfixes
Percpu areas are only allocated for possible cpus. In general, you
shouldn't access random cpu's percpu areas.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Hirokazu Takata <takata@linux-m32r.org>
struct dentry is one of the most critical structures in the kernel. So it's
sad to see it going neglected.
With CONFIG_PROFILING turned on (which is probably the common case at least
for distros and kernel developers), sizeof(struct dcache) == 208 here
(64-bit). This gives 19 objects per slab.
I packed d_mounted into a hole, and took another 4 bytes off the inline
name length to take the padding out from the end of the structure. This
shinks it to 200 bytes. I could have gone the other way and increased the
length to 40, but I'm aiming for a magic number, read on...
I then got rid of the d_cookie pointer. This shrinks it to 192 bytes. Rant:
why was this ever a good idea? The cookie system should increase its hash
size or use a tree or something if lookups are a problem. Also the "fast
dcookie lookups" in oprofile should be moved into the dcookie code -- how
can oprofile possibly care about the dcookie_mutex? It gets dropped after
get_dcookie() returns so it can't be providing any sort of protection.
At 192 bytes, 21 objects fit into a 4K page, saving about 3MB on my system
with ~140 000 entries allocated. 192 is also a multiple of 64, so we get
nice cacheline alignment on 64 and 32 byte line systems -- any given dentry
will now require 3 cachelines to touch all fields wheras previously it
would require 4.
I know the inline name size was chosen quite carefully, however with the
reduction in cacheline footprint, it should actually be just about as fast
to do a name lookup for a 36 character name as it was before the patch (and
faster for other sizes). The memory footprint savings for names which are
<= 32 or > 36 bytes long should more than make up for the memory cost for
33-36 byte names.
Performance is a feature...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
* 'irq-fixes-for-linus-4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sparseirq: move __weak symbols into separate compilation unit
sparseirq: work around __weak alias bug
sparseirq: fix hang with !SPARSE_IRQ
sparseirq: set lock_class for legacy irq when sparse_irq is selected
sparseirq: work around compiler optimizing away __weak functions
sparseirq: fix desc->lock init
sparseirq: do not printk when migrating IRQ descriptors
sparseirq: remove duplicated arch_early_irq_init()
irq: simplify for_each_irq_desc() usage
proc: remove ifdef CONFIG_SPARSE_IRQ from stat.c
irq: for_each_irq_desc() move to irqnr.h
hrtimer: remove #include <linux/irq.h>
The invlpg and sync walkers lack knowledge of large host sptes,
descending to non-existant pagetable level.
Stop at directory level in such case.
Fixes SMP Windows XP with hugepages.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
While most accesses to the i8259 are with the kvm mutex taken, the call
to kvm_pic_read_irq() is not. We can't easily take the kvm mutex there
since the function is called with interrupts disabled.
Fix by adding a spinlock to the virtual interrupt controller. Since we
can't send an IPI under the spinlock (we also take the same spinlock in
an irq disabled context), we defer the IPI until the spinlock is released.
Similarly, we defer irq ack notifications until after spinlock release to
avoid lock recursion.
Signed-off-by: Avi Kivity <avi@redhat.com>
The pte.g bit is meaningless if global pages are disabled; deferring
mmu page synchronization on these ptes will lead to the guest using stale
shadow ptes.
Fixes Vista x86 smp bootloader failure.
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix kvm_arch_vcpu_ioctl_[gs]et_regs() to do something meaningful on
ia64. Old versions could never have worked since they required
pointers to be set in the ioctl payload which were never being set by
the ioctl handler for get_regs.
In addition reserve extra space for future extensions.
The change of layout of struct kvm_regs doesn't require adding a new
CAP since get/set regs never worked on ia64 until now.
This version doesn't support copying the KVM kernel stack in/out of
the kernel. This should be implemented in a seperate ioctl call if
ever needed.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Acked-by : Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There is no point in doing the ready_for_nmi_injection/
request_nmi_window dance with user space. First, we don't do this for
in-kernel irqchip anyway, while the code path is the same as for user
space irqchip mode. And second, there is nothing to loose if a pending
NMI is overwritten by another one (in contrast to IRQs where we have to
save the number). Actually, there is even the risk of raising spurious
NMIs this way because the reason for the held-back NMI might already be
handled while processing the first one.
Therefore this patch creates a simplified user space NMI injection
interface, exporting it under KVM_CAP_USER_NMI and dropping the old
KVM_CAP_NMI capability. And this time we also take care to provide the
interface only on archs supporting NMIs via KVM (right now only x86).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
As with the kernel irqchip, don't allow an NMI to stomp over an already
injected IRQ; instead wait for the IRQ injection to be completed.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
walk_shadow assumes the caller verified validity of the pdptr pointer in
question, which is not the case for the invlpg handler.
Fixes oops during Solaris 10 install.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm_get_tsc_khz() currently returns the previously-calculated preset_lpj
value, but it is in loops-per-jiffy, not kHz. The current code works
correctly only when HZ=1000.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If the guest executes invlpg, peek into the pagetable and attempt to
prepopulate the shadow entry.
Also stop dirty fault updates from interfering with the fork detector.
2% improvement on RHEL3/AIM7.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Skip syncing global pages on cr3 switch (but not on cr4/cr0). This is
important for Linux 32-bit guests with PAE, where the kmap page is
marked as global.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Collapse remote TLB flushes on root sync.
kernbench is 2.7% faster on 4-way guest. Improvements have been seen
with other loads such as AIM7.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of invoking the handler directly collect pages into
an array so the caller can work with it.
Simplifies TLB flush collapsing.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The VMMCALL instruction doesn't get recognised and isn't processed
by the emulator.
This is seen on an Intel host that tries to execute the VMMCALL
instruction after a guest live migrates from an AMD host.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add emulation of shld and shrd instructions
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add the assembler code for instruction with three operands and one
operand is stored in ECX register
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add SrcOne operand type when we need to decode an implied '1' like with
regular shift instruction
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instruction like shld has three operands, so we need to add a Src2
decode set. We start with Src2None, Src2CL, and Src2ImmByte, Src2One to
support shld/shrd and we will expand it later.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
Extend the opcode descriptor to 32 bits. This is needed by the
introduction of a new Src2 operand type.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
The only significant changes were to kvmppc_exit_timing_write() and
kvmppc_exit_timing_show(), both of which were dramatically simplified.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Existing KVM statistics are either just counters (kvm_stat) reported for
KVM generally or trace based aproaches like kvm_trace.
For KVM on powerpc we had the need to track the timings of the different exit
types. While this could be achieved parsing data created with a kvm_trace
extension this adds too much overhead (at least on embedded PowerPC) slowing
down the workloads we wanted to measure.
Therefore this patch adds a in-kernel exit timing statistic to the powerpc kvm
code. These statistic is available per vm&vcpu under the kvm debugfs directory.
As this statistic is low, but still some overhead it can be enabled via a
.config entry and should be off by default.
Since this patch touched all powerpc kvm_stat code anyway this code is now
merged and simplified together with the exit timing statistic code (still
working with exit timing disabled in .config).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Store shadow TLB entries in memory, but only use it on host context switch
(instead of every guest entry). This improves performance for most workloads on
440 by reducing the guest TLB miss rate.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Formerly, we used to maintain a per-vcpu shadow TLB and on every entry to the
guest would load this array into the hardware TLB. This consumed 1280 bytes of
memory (64 entries of 16 bytes plus a struct page pointer each), and also
required some assembly to loop over the array on every entry.
Instead of saving a copy in memory, we can just store shadow mappings directly
into the hardware TLB, accepting that the host kernel will clobber these as
part of the normal 440 TLB round robin. When we do that we need less than half
the memory, and we have decreased the exit handling time for all guest exits,
at the cost of increased number of TLB misses because the host overwrites some
guest entries.
These savings will be increased on processors with larger TLBs or which
implement intelligent flush instructions like tlbivax (which will avoid the
need to walk arrays in software).
In addition to that and to the code simplification, we have a greater chance of
leaving other host userspace mappings in the TLB, instead of forcing all
subsequent tasks to re-fault all their mappings.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM currently ignores the host's round robin TLB eviction selection, instead
maintaining its own TLB state and its own round robin index. However, by
participating in the normal 44x TLB selection, we can drop the alternate TLB
processing in KVM. This results in a significant performance improvement,
since that processing currently must be done on *every* guest exit.
Accordingly, KVM needs to be able to access and increment tlb_44x_index.
(KVM on 440 cannot be a module, so there is no need to export this symbol.)
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
KVM on 440 has always been able to handle large guest mappings with 4K host
pages -- we must, since the guest kernel uses 256MB mappings.
This patch makes KVM work when the host has large pages too (tested with 64K).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Impact: make global function static
arch/x86/kvm/vmx.c:134:3: warning: symbol 'vmx_capability' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
The s390 backend of kvm never calls kvm_vcpu_uninit. This causes
a memory leak of vcpu->run pages.
Lets call kvm_vcpu_uninit in kvm_arch_vcpu_destroy to free
the vcpu->run.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently it is impossible to unload the kvm module on s390.
This patch fixes kvm_arch_destroy_vm to release all cpus.
This make it possible to unload the module.
In addition we stop messing with the module refcount in arch code.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The write protect verification in set_spte is unnecessary for page sync.
Its guaranteed that, if the unsync spte was writable, the target page
does not have a write protected shadow (if it had, the spte would have
been write protected under mmu_lock by rmap_write_protect before).
Same reasoning applies to mark_page_dirty: the gfn has been marked as
dirty via the pagefault path.
The cost of hash table and memslot lookups are quite significant if the
workload is pagetable write intensive resulting in increased mmu_lock
contention.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently, we only set the KVM paravirt signature in case
of CONFIG_KVM_GUEST. However, it is possible to have it turned
off, while CONFIG_KVM_CLOCK is turned on. This is also a paravirt
case, and should be shown accordingly.
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If we're injecting an interrupt, and another one is pending, request
an interrupt window notification so we don't have excess latency on the
second interrupt.
This shouldn't happen in practice since an EOI will be issued, giving a second
chance to request an interrupt window, but...
Signed-off-by: Avi Kivity <avi@redhat.com>
Since vmm runs in an isolated address space and it is just a copy
of host's kvm-intel module, so once vmm crashes, we just crash all guests
running on it instead of crashing whole kernel.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use printk infrastructure to print out some debug info once VM crashes.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
kvm-intel module is relocated to an isolated address space
with kernel, so it can't call host kernel's printk for debug
purpose. In the module, we implement the printk to output debug
info of vmm.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
On emergency_restart, we may need to use an NMI to disable virtualization
on all CPUs. We do that using nmi_shootdown_cpus() if VMX is enabled.
Note: With this patch, we will run the NMI stuff only when the CPU where
emergency_restart() was called has VMX enabled. This should work on most
cases because KVM enables VMX on all CPUs, but we may miss the small
window where KVM is doing that. Also, I don't know if all code using
VMX out there always enable VMX on all CPUs like KVM does. We have two
other alternatives for that:
a) Have an API that all code that enables VMX on any CPU should use
to tell the kernel core that it is going to enable VMX on the CPUs.
b) Always call nmi_shootdown_cpus() if the CPU supports VMX. This is
a bit intrusive and more risky, as it would run nmi_shootdown_cpus()
on emergency_reboot() even on systems where virtualization is never
enabled.
Finding a proper point to hook the nmi_shootdown_cpus() call isn't
trivial, as the non-emergency machine_restart() (that doesn't need the
NMI tricks) uses machine_emergency_restart() directly.
The solution to make this work without adding a new function or argument
to machine_ops was setting a 'reboot_emergency' flag that tells if
native_machine_emergency_restart() needs to do the virt cleanup or not.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We need to disable virtualization extensions on all CPUs before booting
the kdump kernel, otherwise the kdump kernel booting will fail, and
rebooting after the kdump kernel did its task may also fail.
We do it using cpu_emergency_vmxoff() and cpu_emergency_svm_disable(),
that should always work, because those functions check if the CPUs
support SVM or VMX before doing their tasks.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This function can be used by the reboot or kdump code to forcibly
disable SVM on the CPU.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Use a trick to keep the printk()s on has_svm() working as before. gcc
will take care of not generating code for the 'msg' stuff when the
function is called with a NULL msg argument.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Add cpu_emergency_vmxoff() and its friends: cpu_vmx_enabled() and
__cpu_emergency_vmxoff().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Along with some comments on why it is different from the core cpu_vmxoff()
function.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Unfortunately we can't use exactly the same code from vmx
hardware_disable(), because the KVM function uses the
__kvm_handle_fault_on_reboot() tricks.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
It will be used by core code on kdump and reboot, to disable
vmx if needed.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Those definitions will be used by code outside KVM, so move it outside
of a KVM-specific source file.
Those definitions are used only on kvm/vmx.c, that already includes
asm/vmx.h, so they can be moved safely.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
svm.h will be used by core code that is independent of KVM, so I am
moving it outside the arch/x86/kvm directory.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
vmx.h will be used by core code that is independent of KVM, so I am
moving it outside the arch/x86/kvm directory.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We used to defer invalidating userspace TLB entries until jumping out of the
kernel. This was causing MMU weirdness most easily triggered by using a pipe in
the guest, e.g. "dmesg | tail". I believe the problem was that after the guest
kernel changed the PID (part of context switch), the old process's mappings
were still present, and so copy_to_user() on the "return to new process" path
ended up using stale mappings.
Testing with large pages (64K) exposed the problem, probably because with 4K
pages, pressure on the TLB faulted all process A's mappings out before the
guest kernel could insert any for process B.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Bare metal Linux on 440 can "overmap" RAM in the kernel linear map, so that it
can use large (256MB) mappings even if memory isn't a multiple of 256MB. To
prevent the hardware prefetcher from loading from an invalid physical address
through that mapping, it's marked Guarded.
However, KVM must ensure that all guest mappings are backed by real physical
RAM (since a deliberate access through a guarded mapping could still cause a
machine check). Accordingly, we don't need to make our mappings guarded, so
let's allow prefetching as the designers intended.
Curiously this patch didn't affect performance at all on the quick test I
tried, but it's clearly the right thing to do anyways and may improve other
workloads.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Make sure that CONFIG_KVM cannot be selected without processor support
(currently, 440 is the only processor implementation available).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The code to traverse the cpuid data array list for counting type of leaves is
currently broken.
This patches fixes the 2 things in it.
1. Set the 1st counting entry's flag KVM_CPUID_FLAG_STATE_READ_NEXT. Without
it the code will never find a valid entry.
2. Also the stop condition in the for loop while looking for the next unflaged
entry is broken. It needs to stop when it find one matching entry;
and in the case of count of 1, it will be the same entry found in this
iteration.
Signed-Off-By: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
For cpuid leaf 0xb the bits 8-15 in ECX register define the end of counting
leaf. The previous code was using bits 0-7 for this purpose, which is
a bug.
Signed-off-by: Nitin A Kamble <nitin.a.kamble@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
set ESR[PTR] when emulating a guest trap. This allows Linux guests to
properly handle WARN_ON() (i.e. detect that it's a non-fatal trap).
Also remove debugging printk in trap emulation.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In kvmppc_deliver_interrupt is just one case left in the switch and it is a
rare one (less than 8%) when looking at the exit numbers. Therefore we can
at least drop the switch/case and if an if. I inserted an unlikely too, but
that's open for discussion.
In kvmppc_can_deliver_interrupt all frequent cases are in the default case.
I know compilers are smart but we can make it easier for them. By writing
down all options and removing the default case combined with the fact that
ithe values are constants 0..15 should allow the compiler to write an easy
jump table.
Modifying kvmppc_can_deliver_interrupt pointed me to the fact that gcc seems
to be unable to reduce priority_exception[x] to a build time constant.
Therefore I changed the usage of the translation arrays in the interrupt
delivery path completely. It is now using priority without translation to irq
on the full irq delivery path.
To be able to do that ivpr regs are stored by their priority now.
Additionally the decision made in kvmppc_can_deliver_interrupt is already
sufficient to get the value of interrupt_msr_mask[x]. Therefore we can replace
the 16x4byte array used here with a single 4byte variable (might still be one
miss, but the chance to find this in cache should be better than the right
entry of the whole array).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Since we use a unsigned long here anyway we can use the optimized __ffs.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently we use an unnecessary if&switch to detect some cases.
To be honest we don't need the ligh_exits counter anyway, because we can
calculate it out of others. Sum_exits can also be calculated, so we can
remove that too.
MMIO, DCR and INTR can be counted on other places without these
additional control structures (The INTR case was never hit anyway).
The handling of BOOKE_INTERRUPT_EXTERNAL/BOOKE_INTERRUPT_DECREMENTER is
similar, but we can avoid the additional if when copying 3 lines of code.
I thought about a goto there to prevent duplicate lines, but rewriting three
lines should be better style than a goto cross switch/case statements (its
also not enough code to justify a new inline function).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When changing some msr bits e.g. problem state we need to take special
care of that. We call the function in our mtmsr emulation (not needed for
wrtee[i]), but we don't call kvmppc_set_msr if we change msr via set_regs
ioctl.
It's a corner case we never hit so far, but I assume it should be
kvmppc_set_msr in our arch set regs function (I found it because it is also
a corner case when using pv support which would miss the update otherwise).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
However, some of these fields could be split into separate per-core structures
in the future.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch doesn't yet move all 44x-specific data into the new structure, but
is the first step down that path. In the future we may also want to create a
struct kvm_vcpu_booke.
Based on patch from Liu Yu <yu.liu@freescale.com>.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Cores provide 3 emulation hooks, implemented for example in the new
4xx_emulate.c:
kvmppc_core_emulate_op
kvmppc_core_emulate_mtspr
kvmppc_core_emulate_mfspr
Strictly speaking the last two aren't necessary, but provide for more
informative error reporting ("unknown SPR").
Long term I'd like to have instruction decoding autogenerated from tables of
opcodes, and that way we could aggregate universal, Book E, and core-specific
instructions more easily and without redundant switch statements.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This is used in a couple places in KVM, but isn't KVM-specific.
However, this patch doesn't modify other in-kernel emulation code:
- xmon uses a direct copy of ppc_opc.c from binutils
- emulate_instruction() doesn't need it because it can use a series
of mask tests.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Avi Kivity <avi@redhat.com>
This introduces a set of core-provided hooks. For 440, some of these are
implemented by booke.c, with the rest in (the new) 44x.c.
Note that these hooks are link-time, not run-time. Since it is not possible to
build a single kernel for both e500 and 440 (for example), using function
pointers would only add overhead.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The division was somewhat artificial and cumbersome, and had no functional
benefit anyways: we can only guests built for the real host processor.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will ease ports to other cores.
Also remove unused "struct kvm_tlb" while we're at it.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This will make it easier to provide implementations for other cores.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Some areas of kvm x86 mmu are using gfn offset inside a slot without
unaliasing the gfn first. This patch makes sure that the gfn will be
unaliased and add gfn_to_memslot_unaliased() to save the calculating
of the gfn unaliasing in case we have it unaliased already.
Signed-off-by: Izik Eidus <ieidus@redhat.com>
Acked-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Ideally, every assigned device should in a clear condition before and after
assignment, so that the former state of device won't affect later work.
Some devices provide a mechanism named Function Level Reset, which is
defined in PCI/PCI-e document. We should execute it before and after device
assignment.
(But sadly, the feature is new, and most device on the market now don't
support it. We are considering using D0/D3hot transmit to emulate it later,
but not that elegant and reliable as FLR itself.)
[Update: Reminded by Xiantao, execute FLR after we ensure that the device can
be assigned to the guest.]
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Remove the lock protection for kvm halt logic, otherwise,
once other vcpus want to acquire the lock, and they have to
wait all vcpus are waken up from halt.
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
If emulate_invalid_guest_state is enabled, the emulator is called
when guest state is invalid. Until now, we reported an mmio failure
when emulate_instruction() returned EMULATE_DO_MMIO. This patch adds
the case where emulate_instruction() failed and an MMIO emulation
is needed.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
If we call the emulator we shouldn't call skip_emulated_instruction()
in the first place, since the emulator already computes the next rip
for us. Thus we move ->skip_emulated_instruction() out of
kvm_emulate_pio() and into handle_io() (and the svm equivalent). We
also replaced "return 0" by "break" in the "do_io:" case because now
the shadow register state needs to be committed. Otherwise eip will never
be updated.
Signed-off-by: Guillaume Thouvenin <guillaume.thouvenin@ext.bull.net>
Signed-off-by: Avi Kivity <avi@redhat.com>
The busy flag of the TR selector is not set by the hardware. This breaks
migration from amd hosts to intel hosts.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The hardware does not set the 'g' bit of the cs selector and this breaks
migration from amd hosts to intel hosts. Set this bit if the segment
limit is beyond 1 MB.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
As suggested by Avi, this patch introduces a counter of VCPUs that have
LVT0 set to NMI mode. Only if the counter > 0, we push the PIT ticks via
all LAPIC LVT0 lines to enable NMI watchdog support.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch refactors the NMI watchdog delivery patch, consolidating
tests and providing a proper API for delivering watchdog events.
An included micro-optimization is to check only for apic_hw_enabled in
kvm_apic_local_deliver (the test for LVT mask is covering the
soft-disabled case already).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
PCI device assignment would map guest MMIO spaces as separate slot, so it is
possible that the device has more than 2 MMIO spaces and overwrite current
private memslot.
The patch move private memory slot to the top of userspace visible memory slots.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Otherwise set_bit() for private memory slot(above KVM_MEMORY_SLOTS) would
corrupted memory in 32bit host.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The effective memory type of EPT is the mixture of MSR_IA32_CR_PAT and memory
type field of EPT entry.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
GUEST_PAT support is a new feature introduced by Intel Core i7 architecture.
With this, cpu would save/load guest and host PAT automatically, for EPT memory
type in guest depends on MSR_IA32_CR_PAT.
Also add save/restore for MSR_IA32_CR_PAT.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
For KVM can reuse the type define, and need them to support shadow MTRR.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Call kvm_arch_vcpu_reset() instead of directly using arch callback.
The function does additional things.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Older VMX supporting CPUs do not provide the "Virtual NMI" feature for
tracking the NMI-blocked state after injecting such events. For now
KVM is unable to inject NMIs on those CPUs.
Derived from Sheng Yang's suggestion to use the IRQ window notification
for detecting the end of NMI handlers, this patch implements virtual
NMI support without impact on the host's ability to receive real NMIs.
The downside is that the given approach requires some heuristics that
can cause NMI nesting in vary rare corner cases.
The approach works as follows:
- inject NMI and set a software-based NMI-blocked flag
- arm the IRQ window start notification whenever an NMI window is
requested
- if the guest exits due to an opening IRQ window, clear the emulated
NMI-blocked flag
- if the guest net execution time with NMI-blocked but without an IRQ
window exceeds 1 second, force NMI-blocked reset and inject anyway
This approach covers most practical scenarios:
- succeeding NMIs are seperated by at least one open IRQ window
- the guest may spin with IRQs disabled (e.g. due to a bug), but
leaving the NMI handler takes much less time than one second
- the guest does not rely on strict ordering or timing of NMIs
(would be problematic in virtualized environments anyway)
Successfully tested with the 'nmi n' monitor command, the kgdbts
testsuite on smp guests (additional patches required to add debug
register support to kvm) + the kernel's nmi_watchdog=1, and a Siemens-
specific board emulation (+ guest) that comes with its own NMI
watchdog mechanism.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch adds the required bits to the VMX side for user space
injected NMIs. As with the preexisting in-kernel irqchip support, the
CPU must provide the "virtual NMI" feature for proper tracking of the
NMI blocking state.
Based on the original patch by Sheng Yang.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Introduces the KVM_NMI IOCTL to the generic x86 part of KVM for
injecting NMIs from user space and also extends the statistic report
accordingly.
Based on the original patch by Sheng Yang.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Kick the NMI receiving VCPU in case the triggering caller runs in a
different context.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Ensure that a VCPU with pending NMIs is considered runnable.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
LINT0 of the LAPIC can be used to route PIT events as NMI watchdog ticks
into the guest. This patch aligns the in-kernel irqchip emulation with
the user space irqchip with already supports this feature. The trick is
to route PIT interrupts to all LAPIC's LVT0 lines.
Rebased and slightly polished patch originally posted by Sheng Yang.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Fix NMI injection in real-mode with the same pattern we perform IRQ
injection.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
do_interrupt_requests and vmx_intr_assist go different way for
achieving the same: enabling the nmi/irq window start notification.
Unify their code over enable_{irq|nmi}_window, get rid of a redundant
call to enable_intr_window instead of direct enable_nmi_window
invocation and unroll enable_intr_window for both in-kernel and user
space irq injection accordingly.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
There are currently two ways in VMX to check if an IRQ or NMI can be
injected:
- vmx_{nmi|irq}_enabled and
- vcpu.arch.{nmi|interrupt}_window_open.
Even worse, one test (at the end of vmx_vcpu_run) uses an inconsistent,
likely incorrect logic.
This patch consolidates and unifies the tests over
{nmi|interrupt}_window_open as cache + vmx_update_window_states
for updating the cache content.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
CPU reset invalidates pending or already injected NMIs, therefore reset
the related state variables.
Based on original patch by Gleb Natapov.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Properly set GUEST_INTR_STATE_NMI and reset nmi_injected when a
task-switch vmexit happened due to a task gate being used for handling
NMIs. Also avoid the false warning about valid vectoring info in
kvm_handle_exit.
Based on original patch by Gleb Natapov.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
irq_window_exits only tracks IRQ window exits due to user space
requests, nmi_window_exits include all exits. The latter makes more
sense, so let's adjust irq_window_exits accounting.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The extract cpu time instruction (ectg) instruction allows the user
process to get the current thread cputime without calling into the
kernel. The code that uses the instruction needs to switch to the
access registers mode to get access to the per-cpu info page that
contains the two base values that are needed to calculate the current
cputime from the CPU timer with the ectg instruction.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Distinguish the cputime of the idle process where idle is actually using
cpu cycles from the cputime where idle is sleeping on an enabled wait psw.
The former is accounted as system time, the later as idle time.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Increase the precision of the idle time calculation that is exported
to user space via /sys/devices/system/cpu/cpu<x>/idle_time_us
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The unit of the cputime accouting values that are stored per process is
currently a microsecond. The CPU timer has a maximum granularity of
2**-12 microseconds. There is no benefit in storing the per process values
in the lesser precision and there is the disadvantage that the backend
has to do the rounding to microseconds. The better solution is to use
the maximum granularity of the CPU timer as cputime unit.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cpu time spent by the idle process actually doing something is
currently accounted as idle time. This is plain wrong, the architectures
that support VIRT_CPU_ACCOUNTING=y can do better: distinguish between the
time spent doing nothing and the time spent by idle doing work. The first
is accounted with account_idle_time and the second with account_system_time.
The architectures that use the account_xxx_time interface directly and not
the account_xxx_ticks interface now need to do the check for the idle
process in their arch code. In particular to improve the system vs true
idle time accounting the arch code needs to measure the true idle time
instead of just testing for the idle process.
To improve the tick based accounting as well we would need an architecture
primitive that can tell us if the pt_regs of the interrupted context
points to the magic instruction that halts the cpu.
In addition idle time is no more added to the stime of the idle process.
This field now contains the system time of the idle process as it should
be. On systems without VIRT_CPU_ACCOUNTING this will always be zero as
every tick that occurs while idle is running will be accounted as idle
time.
This patch contains the necessary common code changes to be able to
distinguish idle system time and true idle time. The architectures with
support for VIRT_CPU_ACCOUNTING need some changes to exploit this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The utimescaled / stimescaled fields in the task structure and the
global cpustat should be set on all architectures. On s390 the calls
to account_user_time_scaled and account_system_time_scaled never have
been added. In addition system time that is accounted as guest time
to the user time of a process is accounted to the scaled system time
instead of the scaled user time.
To fix the bugs and to prevent future forgetfulness this patch merges
account_system_time_scaled into account_system_time and
account_user_time_scaled into account_user_time.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Michael Neuling <mikey@neuling.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
lguest: struct device - replace bus_id with dev_name()
lguest: move the initial guest page table creation code to the host
kvm-s390: implement config_changed for virtio on s390
virtio_console: support console resizing
virtio: add PCI device release() function
virtio_blk: fix type warning
virtio: block: dynamic maximum segments
virtio: set max_segment_size and max_sectors to infinite.
virtio: avoid implicit use of Linux page size in balloon interface
virtio: hand virtio ring alignment as argument to vring_new_virtqueue
virtio: use KVM_S390_VIRTIO_RING_ALIGN instead of relying on pagesize
virtio: use LGUEST_VRING_ALIGN instead of relying on pagesize
virtio: Don't use PAGE_SIZE for vring alignment in virtio_pci.
virtio: rename 'pagesize' arg to vring_init/vring_size
virtio: Don't use PAGE_SIZE in virtio_pci.c
virtio: struct device - replace bus_id with dev_name(), dev_set_name()
virtio-pci queue allocation not page-aligned
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
* 'oprofile-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
oprofile: select RING_BUFFER
ring_buffer: adding EXPORT_SYMBOLs
oprofile: fix lost sample counter
oprofile: remove nr_available_slots()
oprofile: port to the new ring_buffer
ring_buffer: add remaining cpu functions to ring_buffer.h
oprofile: moving cpu_buffer_reset() to cpu_buffer.h
oprofile: adding cpu_buffer_entries()
oprofile: adding cpu_buffer_write_commit()
oprofile: adding cpu buffer r/w access functions
ftrace: remove unused function arg in trace_iterator_increment()
ring_buffer: update description for ring_buffer_alloc()
oprofile: set values to default when creating oprofilefs
oprofile: implement switch/case in buffer_sync.c
x86/oprofile: cleanup IBS init/exit functions in op_model_amd.c
x86/oprofile: reordering IBS code in op_model_amd.c
oprofile: fix typo
oprofile: whitspace changes only
oprofile: update comment for oprofile_add_sample()
oprofile: comment cleanup
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-next-2.6: (98 commits)
sparc: move select of ARCH_SUPPORTS_MSI
sparc: drop SUN_IO
sparc: unify sections.h
sparc: use .data.init_task section for init_thread_union
sparc: fix array overrun check in of_device_64.c
sparc: unify module.c
sparc64: prepare module_64.c for unification
sparc64: use bit neutral Elf symbols
sparc: unify module.h
sparc: introduce CONFIG_BITS
sparc: fix hardirq.h removal fallout
sparc64: do not export pus_fs_struct
sparc: use sparc64 version of scatterlist.h
sparc: Commonize memcmp assembler.
sparc: Unify strlen assembler.
sparc: Add asm/asm.h
sparc: Kill memcmp_32.S code which has been ifdef'd out for centuries.
sparc: replace for_each_cpu_mask_nr with for_each_cpu
sparc: fix sparse warnings in irq_32.c
sparc: add include guards to kernel.h
...
* 'for-2.6.29' of git://git.kernel.dk/linux-2.6-block: (43 commits)
bio: get rid of bio_vec clearing
bounce: don't rely on a zeroed bio_vec list
cciss: simplify parameters to deregister_disk function
cfq-iosched: fix race between exiting queue and exiting task
loop: Do not call loop_unplug for not configured loop device.
loop: Flush possible running bios when loop device is released.
alpha: remove dead BIO_VMERGE_BOUNDARY
Get rid of CONFIG_LSF
block: make blk_softirq_init() static
block: use min_not_zero in blk_queue_stack_limits
block: add one-hit cache for disk partition lookup
cfq-iosched: remove limit of dispatch depth of max 4 times quantum
nbd: tell the block layer that it is not a rotational device
block: get rid of elevator_t typedef
aio: make the lookup_ioctx() lockless
bio: add support for inlining a number of bio_vecs inside the bio
bio: allow individual slabs in the bio_set
bio: move the slab pointer inside the bio_set
bio: only mempool back the largest bio_vec slab cache
block: don't use plugging on SSD devices
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, sparseirq: clean up Kconfig entry
x86: turn CONFIG_SPARSE_IRQ off by default
sparseirq: fix numa_migrate_irq_desc dependency and comments
sparseirq: add kernel-doc notation for new member in irq_desc, -v2
locking, irq: enclose irq_desc_lock_class in CONFIG_LOCKDEP
sparseirq, xen: make sure irq_desc is allocated for interrupts
sparseirq: fix !SMP building, #2
x86, sparseirq: move irq_desc according to smp_affinity, v7
proc: enclose desc variable of show_stat() in CONFIG_SPARSE_IRQ
sparse irqs: add irqnr.h to the user headers list
sparse irqs: handle !GENIRQ platforms
sparseirq: fix !SMP && !PCI_MSI && !HT_IRQ build
sparseirq: fix Alpha build failure
sparseirq: fix typo in !CONFIG_IO_APIC case
x86, MSI: pass irq_cfg and irq_desc
x86: MSI start irq numbering from nr_irqs_gsi
x86: use NR_IRQS_LEGACY
sparse irq_desc[] array: core kernel and x86 changes
genirq: record IRQ_LEVEL in irq_desc[]
irq.h: remove padding from irq_desc on 64bits
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
hrtimers: fix warning in kernel/hrtimer.c
x86: make sure we really have an hpet mapping before using it
x86: enable HPET on Fujitsu u9200
linux/timex.h: cleanup for userspace
posix-timers: simplify de_thread()->exit_itimers() path
posix-timers: check ->it_signal instead of ->it_pid to validate the timer
posix-timers: use "struct pid*" instead of "struct task_struct*"
nohz: suppress needless timer reprogramming
clocksource, acpi_pm.c: put acpi_pm_read_slow() under CONFIG_PCI
nohz: no softirq pending warnings for offline cpus
hrtimer: removing all ur callback modes, fix
hrtimer: removing all ur callback modes, fix hotplug
hrtimer: removing all ur callback modes
x86: correct link to HPET timer specification
rtc-cmos: export second NVRAM bank
Fixed up conflicts in sound/drivers/pcsp/pcsp.c and sound/core/hrtimer.c
manually.
* 'core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
stacktrace: provide save_stack_trace_tsk() weak alias
rcu: provide RCU options on non-preempt architectures too
printk: fix discarding message when recursion_bug
futex: clean up futex_(un)lock_pi fault handling
"Tree RCU": scalable classic RCU implementation
futex: rename field in futex_q to clarify single waiter semantics
x86/swiotlb: add default swiotlb_arch_range_needs_mapping
x86/swiotlb: add default phys<->bus conversion
x86: unify pci iommu setup and allow swiotlb to compile for 32 bit
x86: add swiotlb allocation functions
swiotlb: consolidate swiotlb info message printing
swiotlb: support bouncing of HighMem pages
swiotlb: factor out copy to/from device
swiotlb: add arch hook to force mapping
swiotlb: allow architectures to override phys<->bus<->phys conversions
swiotlb: add comment where we handle the overflow of a dma mask on 32 bit
rcu: fix rcutorture behavior during reboot
resources: skip sanity check of busy resources
swiotlb: move some definitions to header
swiotlb: allow architectures to override swiotlb pool allocation
...
Fix up trivial conflicts in
arch/x86/kernel/Makefile
arch/x86/mm/init_32.c
include/linux/hardirq.h
as per Ingo's suggestions.
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/xsave.c:162:5: warning: symbol 'restore_user_xstate' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/apic.c:270:5: warning: symbol 'x2apic_icr_read' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/bios_uv.c:28:18: warning: symbol 'uv_systab' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup, reduce kernel size a bit, avoid sparse warnings
Fixes sparse warnings:
arch/x86/kernel/genx2apic_phys.c:164:6: warning: symbol 'x2apic_send_IPI_self' was not declared. Should it be static?
arch/x86/kernel/genx2apic_phys.c:169:6: warning: symbol 'init_x2apic_ldr' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/amd_iommu.c:1299:6: warning: symbol 'prealloc_protection_domains' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/amd_iommu_init.c:246:13: warning: symbol 'iommu_enable' was not declared. Should it be static?
arch/x86/kernel/amd_iommu_init.c:259:13: warning: symbol 'iommu_enable_event_logging' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch moves the initial guest page table creation code to the host,
so the launcher keeps working with PAE enabled configs.
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This doesn't really matter, since s390 pagesize is 4k anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Impact: cleanup
Now that arch/x86/pci/pci.h is used in a number of other places as well,
move the lowlevel x86 pci definitions into the architecture include files.
(not to be confused with the existing arch/x86/include/asm/pci.h file,
which provides public details about x86 PCI)
Tested on: X86_32_UP, X86_32_SMP and X86_64_SMP
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/pci-gart_64.c:55:5: warning: symbol 'iommu_fullflush' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, avoid sparse warning
Fixes this sparse warning:
arch/x86/kernel/efi.c:67:5: warning: symbol 'add_efi_memmap' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/io_apic.c:709:6: warning: symbol 'io_apic_sync' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, avoid sparse warning
In asm/mpspec.h moved out pic_mode from CONFIG_X86_32 as it is common
for both 32 and 64 bit.
Fixes this sparse warning for x86_64:
arch/x86/kernel/apic.c:128:5: warning: symbol 'pic_mode' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, avoid 44 sparse warnings, new file asm/sys_ia32.h
Fixes following sparse warnings:
CHECK arch/x86/ia32/sys_ia32.c
arch/x86/ia32/sys_ia32.c:53:17: warning: symbol 'sys32_truncate64' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:60:17: warning: symbol 'sys32_ftruncate64' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:98:17: warning: symbol 'sys32_stat64' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:109:17: warning: symbol 'sys32_lstat64' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:119:17: warning: symbol 'sys32_fstat64' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:128:17: warning: symbol 'sys32_fstatat' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:164:17: warning: symbol 'sys32_mmap' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:195:17: warning: symbol 'sys32_mprotect' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:201:17: warning: symbol 'sys32_pipe' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:215:17: warning: symbol 'sys32_rt_sigaction' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:291:17: warning: symbol 'sys32_sigaction' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:330:17: warning: symbol 'sys32_rt_sigprocmask' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:370:17: warning: symbol 'sys32_alarm' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:383:17: warning: symbol 'sys32_old_select' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:393:17: warning: symbol 'sys32_waitpid' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:401:17: warning: symbol 'sys32_sysfs' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:406:17: warning: symbol 'sys32_sched_rr_get_interval' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:421:17: warning: symbol 'sys32_rt_sigpending' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:445:17: warning: symbol 'sys32_rt_sigqueueinfo' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:472:17: warning: symbol 'sys32_sysctl' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:517:17: warning: symbol 'sys32_pread' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:524:17: warning: symbol 'sys32_pwrite' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:532:17: warning: symbol 'sys32_personality' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:545:17: warning: symbol 'sys32_sendfile' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:565:17: warning: symbol 'sys32_mmap2' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:589:17: warning: symbol 'sys32_olduname' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:626:6: warning: symbol 'sys32_uname' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:641:6: warning: symbol 'sys32_ustat' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:663:17: warning: symbol 'sys32_execve' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:678:17: warning: symbol 'sys32_clone' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:693:6: warning: symbol 'sys32_lseek' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:698:6: warning: symbol 'sys32_kill' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:703:6: warning: symbol 'sys32_fadvise64_64' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:712:6: warning: symbol 'sys32_vm86_warning' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:726:6: warning: symbol 'sys32_lookup_dcookie' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:732:20: warning: symbol 'sys32_readahead' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:738:17: warning: symbol 'sys32_sync_file_range' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:746:17: warning: symbol 'sys32_fadvise64' was not declared. Should it be static?
arch/x86/ia32/sys_ia32.c:753:17: warning: symbol 'sys32_fallocate' was not declared. Should it be static?
CHECK arch/x86/ia32/ia32_signal.c
arch/x86/ia32/ia32_signal.c:126:17: warning: symbol 'sys32_sigsuspend' was not declared. Should it be static?
arch/x86/ia32/ia32_signal.c:141:17: warning: symbol 'sys32_sigaltstack' was not declared. Should it be static?
arch/x86/ia32/ia32_signal.c:249:17: warning: symbol 'sys32_sigreturn' was not declared. Should it be static?
arch/x86/ia32/ia32_signal.c:279:17: warning: symbol 'sys32_rt_sigreturn' was not declared. Should it be static?
CHECK arch/x86/ia32/ipc32.c
arch/x86/ia32/ipc32.c:12:17: warning: symbol 'sys32_ipc' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix section mismatch warning
Commit b2bb855491 ("x86: Remove cpumask games
in x86/kernel/cpu/intel_cacheinfo.c") introduced get_cpu_leaves(), which
references __cpuinit cpuid4_cache_lookup().
Mark get_cpu_leaves() with a __cpuinit annotation.
Signed-off-by: Sergio Luis <sergio@larces.uece.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PXA27x and later processors support overlay1 and overlay2 on-top of the
base framebuffer (although under-neath the base is also possible). They
support palette and no-palette RGB formats, as well as YUV formats (only
available on overlay2). These overlays have dedicated DMA channels and
behave in a similar way as a framebuffer.
This heavily simplified and re-structured work is based on the original
pxafb_overlay.c (which is pending for mainline merge for a long time).
The major problems with this pxafb_overlay.c are (if you are interested
in the history):
1. heavily redundant (the control logics for overlay1 and overlay2 are
actually identical except for some small operations, which are now
abstracted into a 'pxafb_layer_ops' structure)
2. a lot of useless and un-tested code (two workarounds which are now
fixed on mature silicons)
3. cursorfb is actually useless, hardware cursor should not be used
this way, and the code was actually un-tested for a long time.
The code in this patch should be self-explanatory, I tried to add minimum
comments. As said, this is basically simplified, there are several things
still on the pending list:
1. palette mode is un-supported and un-tested (although re-using the
palette code of the base framebuffer is actually very easy now with
previous clean-up patches)
2. fb_pan_display for overlay(s) is un-supported
3. the base framebuffer can actually be abstracted by 'pxafb_layer' as
well, which will help further re-use of the code and keep a better
and consistent structure. (This is the reason I named it 'pxafb_layer'
instead of 'pxafb_overlay' or something alike)
See Documentation/fb/pxafb.txt for additional usage information.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
1. introduce var_to_depth() to calculate the color depth including the
transparency bit
2. the conversion from 'fb_var_screeninfo' to LCCR3 BPP bits can be re-
used by overlays (in OVLxC1), thus an individual pxafb_var_to_bpp()
has been separated out.
3. pxafb_setmode() should really set the color bitfields correctly at
begining, introduce a pxafb_set_pixfmt() for this
4. allow user apps to specify color formats within fb_var_screeninfo,
and checking of this in pxafb_check_var() has been simplified as
below:
a) pxafb_var_to_bpp() should pass - which means a basically correct
bits_per_pixel and color depth setting
b) the RGBT bitfields are then forced into supported values by
pxafb_set_pixfmt()
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
Add the palette format support for LCCR4_PAL_FOR_3, and fix the
issue of LCCR4 being never assigned.
Also remove the useless pxafb_set_truecolor().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
dma branching is enabled by extending the current setup_frame_dma()
function to allow a 2nd set of frame/palette dma descriptors to be
used.
As a result, pxafb_dma_buff.dma_desc[], pxafb_dma_buff.pal_desc[]
and pxafb_info.fdadr[] are doubled.
This allows maximum re-use of the current dma setup code, although
the pxafb_info.fdadr[xx] for FBRx register values looks a bit odd.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
The amount of video memory size is decided according to the following
order:
1. <xres> x <yres> x <bits_per_pixel> by default, which is the backward
compatible way
2. size specified in platform data
3. size specified in module parameter 'options' string or specified in
kernel boot command line (see updated Documentation/fb/pxafb.txt)
And now since the memory is allocated from system memory, the pxafb_mmap
can be removed and the default fb_mmap() should be working all right.
Also, since we now have introduced the 'struct pxafb_dma_buff' for DMA
descriptors and palettes, the allocation can be separated cleanly.
NOTE: the LCD DMA actually supports chained transfer (i.e. page-based
transfers), to simplify the logic and keep the performance (with less
TLB misses when accessing from memory mapped user space), the memory
is allocated by alloc_pages_*() to ensures it's physical contiguous.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
As Nicolas and Russell pointed out, CLOCK_TICK_RATE is no more
a constant on PXA when multiple processors and platforms are
selected, change TIMER_FREQ in rtc-sa1100.c into a variable.
Since the code to decide the clock tick rate is re-used from
timer.c, introduce a common get_clock_tick_rate() for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
The mm->ioctx_list is currently protected by a reader-writer lock,
so we always grab that lock on the read side for doing ioctx
lookups. As the workload is extremely reader biased, turn this into
an rcu hlist so we can make lookup_ioctx() lockless. Get rid of
the rwlock and use a spinlock for providing update side exclusion.
There's usually only 1 entry on this list, so it doesn't make sense
to look into fancier data structures.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (25 commits)
allow stripping of generated symbols under CONFIG_KALLSYMS_ALL
kbuild: strip generated symbols from *.ko
kbuild: simplify use of genksyms
kernel-doc: check for extra kernel-doc notations
kbuild: add headerdep used to detect inclusion cycles in header files
kbuild: fix string equality testing in tags.sh
kbuild: fix make tags/cscope
kbuild: fix make incompatibility
kbuild: remove TAR_IGNORE
setlocalversion: add git-svn support
setlocalversion: print correct subversion revision
scripts: improve the decodecode script
scripts/package: allow custom options to rpm
genksyms: allow to ignore symbol checksum changes
genksyms: track symbol checksum changes
tags and cscope support really belongs in a shell script
kconfig: fix options to check-lxdialog.sh
kbuild: gen_init_cpio expands shell variables in file names
remove bashisms from scripts/extract-ikconfig
kbuild: teach mkmakfile to be silent
...
This adds support for 16k and 64k page sizes on PowerPC 44x processors.
The PGDIR table is much smaller than a page when using 16k or 64k
pages (512 and 32 bytes respectively) so we allocate the PGDIR with
kzalloc() instead of __get_free_pages().
One PTE table covers rather a large memory area when using 16k or 64k
pages (32MB or 512MB respectively), so we can easily put FIXMAP and
PKMAP in the area covered by one PTE table.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vladimir Panfilov <pvr@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Ensure that total memory size is page-aligned, because otherwise
mark_bootmem() gets upset.
This error case was triggered by using 64 KiB pages in the kernel
while arch/powerpc/boot/4xx.c arbitrarily reduced the amount of memory
by 4096 (to work around a chip bug that affects the last 256 bytes of
physical memory).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: use the new byteorder headers
fbcon: Protect free_irq() by MACH_IS_ATARI check
fbcon: remove broken mac vbl handler
m68k: fix trigraph ignored warning in setox.S
macfb annotations and compiler warning fix
m68k: mac baboon interrupt enable/disable
m68k: machw.h cleanup
m68k: Mac via cleanup and commentry
m68k: Reinstate mac rtc
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
net: Allow dependancies of FDDI & Tokenring to be modular.
igb: Fix build warning when DCA is disabled.
net: Fix warning fallout from recent NAPI interface changes.
gro: Fix potential use after free
sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
sfc: When disabling the NIC, close the device rather than unregistering it
sfc: SFT9001: Add cable diagnostics
sfc: Add support for multiple PHY self-tests
sfc: Merge top-level functions for self-tests
sfc: Clean up PHY mode management in loopback self-test
sfc: Fix unreliable link detection in some loopback modes
sfc: Generate unique names for per-NIC workqueues
802.3ad: use standard ethhdr instead of ad_header
802.3ad: generalize out mac address initializer
802.3ad: initialize ports LACPDU from const initializer
802.3ad: remove typedef around ad_system
802.3ad: turn ports is_individual into a bool
802.3ad: turn ports is_enabled into a bool
802.3ad: make ntt bool
ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
...
Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (241 commits)
sched, trace: update trace_sched_wakeup()
tracing/ftrace: don't trace on early stage of a secondary cpu boot, v3
Revert "x86: disable X86_PTRACE_BTS"
ring-buffer: prevent false positive warning
ring-buffer: fix dangling commit race
ftrace: enable format arguments checking
x86, bts: memory accounting
x86, bts: add fork and exit handling
ftrace: introduce tracing_reset_online_cpus() helper
tracing: fix warnings in kernel/trace/trace_sched_switch.c
tracing: fix warning in kernel/trace/trace.c
tracing/ring-buffer: remove unused ring_buffer size
trace: fix task state printout
ftrace: add not to regex on filtering functions
trace: better use of stack_trace_enabled for boot up code
trace: add a way to enable or disable the stack tracer
x86: entry_64 - introduce FTRACE_ frame macro v2
tracing/ftrace: add the printk-msg-only option
tracing/ftrace: use preempt_enable_no_resched_notrace in ring_buffer_time_stamp()
x86, bts: correctly report invalid bts records
...
Fixed up trivial conflict in scripts/recordmcount.pl due to SH bits
being already partly merged by the SH merge.
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (246 commits)
x86: traps.c replace #if CONFIG_X86_32 with #ifdef CONFIG_X86_32
x86: PAT: fix address types in track_pfn_vma_new()
x86: prioritize the FPU traps for the error code
x86: PAT: pfnmap documentation update changes
x86: PAT: move track untrack pfnmap stubs to asm-generic
x86: PAT: remove follow_pfnmap_pte in favor of follow_phys
x86: PAT: modify follow_phys to return phys_addr prot and return value
x86: PAT: clarify is_linear_pfn_mapping() interface
x86: ia32_signal: remove unnecessary declaration
x86: common.c boot_cpu_stack and boot_exception_stacks should be static
x86: fix intel x86_64 llc_shared_map/cpu_llc_id anomolies
x86: fix warning in arch/x86/kernel/microcode_amd.c
x86: ia32.h: remove unused struct sigfram32 and rt_sigframe32
x86: asm-offset_64: use rt_sigframe_ia32
x86: sigframe.h: include headers for dependency
x86: traps.c declare functions before they get used
x86: PAT: update documentation to cover pgprot and remap_pfn related changes - v3
x86: PAT: add pgprot_writecombine() interface for drivers - v3
x86: PAT: change pgprot_noncached to uc_minus instead of strong uc - v3
x86: PAT: implement track/untrack of pfnmap regions for x86 - v3
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (105 commits)
SELinux: don't check permissions for kernel mounts
security: pass mount flags to security_sb_kern_mount()
SELinux: correctly detect proc filesystems of the form "proc/foo"
Audit: Log TIOCSTI
user namespaces: document CFS behavior
user namespaces: require cap_set{ug}id for CLONE_NEWUSER
user namespaces: let user_ns be cloned with fairsched
CRED: fix sparse warnings
User namespaces: use the current_user_ns() macro
User namespaces: set of cleanups (v2)
nfsctl: add headers for credentials
coda: fix creds reference
capabilities: define get_vfs_caps_from_disk when file caps are not enabled
CRED: Allow kernel services to override LSM settings for task actions
CRED: Add a kernel_service object class to SELinux
CRED: Differentiate objective and effective subjective credentials on a task
CRED: Documentation
CRED: Use creds in file structs
CRED: Prettify commoncap.c
CRED: Make execve() take advantage of copy-on-write credentials
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (132 commits)
sh: oprofile: Fix up the module build.
sh: add UIO support for JPU on SH7722.
serial: sh-sci: Fix up port pinmux for SH7366.
sh: mach-rsk: Use uImage generation by default for rsk7201/7203.
sh: mach-sh03: Fix up pata_platform build breakage.
sh: enable deferred io LCDC on Migo-R
video: sh_mobile_lcdcfb deferred io support
video: deferred io with physically contiguous memory
video: deferred io cleanup
video: fix deferred io fsync()
sh: add LCDC interrupt configuration to AP325 and Migo-R
sh_mobile_lcdc: use FB_SYS helpers instead of FB_CFB
sh: split coherent pages
sh: dma: Kill off ISA DMA wrapper.
sh: Conditionalize the code dumper on CONFIG_DUMP_CODE.
sh: Kill off the unused SH_ALPHANUMERIC debug option.
sh: Enable skipping of bss on debug platforms for sh32 also.
doc: Update sh cpufreq documentation.
sh: mrshpc_setup_windows() needs to be inline.
serial: sh-sci: sci_poll_get_char() is only used by CONFIG_CONSOLE_POLL.
...
Fix the warning: trigraph ??/ ignored, use -trigraphs to enable
caused by the recent removal of -traditional option.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
No-one seems to know how to mask individual baboon interrupts, so we just
mask the umbrella IRQ. This will work as long as only the IDE driver uses
the baboon chip (it can't deadlock). Use mac_enable_irq/mac_disable_irq
rather than enable_irq/disable_irq because the latter routines count the
depth of nested calls which triggers a warning and call trace because
IRQ_NUBUS_C is enabled twice in a row (once when the baboon handler is
registered, and once when the IDE IRQ is registered).
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Remove some more cruft from machw.h and drop the #include where it isn't
needed.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
No behavioural changes, just cleanups and better documentation.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reinstate the Mac hardware clock for CUDA ADB and Mac II ADB models.
It doesn't work properly on Mac IIsi ADB and PMU ADB yet, so leave them
out.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Impact: extend functions with a (yet unused) parameter, update callsites
Some architectures need it - in preparation for highmem swiotlb.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix panic on null pointer with sparseirq
Some GCC versions seem to inline the weak global function,
when that function is empty.
Work it around, by making the functions return a (dummy) integer.
Signed-off-by: Yinghai <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
arch/x86/kernel/apic.c:103:5: warning: symbol 'disable_x2apic' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, avoid sparse warning
Include "../pci/pci.h" for port_cf9_safe
Fixes this sparse warning:
arch/x86/kernel/reboot.c:43:6: warning: symbol 'port_cf9_safe' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It is counter intuitive to have the select listed
as part of the PCI option.
Move the select to the SPARC64 specific part of the config.
PCI_MSI has a dependency on PCI so it does not harm to have
it always selected.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SUN_IO is always 'y' so drop it and thus killing an ifdef/endif pair
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing this use standard names for start/end
so we could use definitions straight from asm-generic
for all the typical symbols.
This also allowed us to drop the use of PROVIDE in the linker
script so sprc is less non-standard on this area.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a dedicated aligned section for the init_thread_union
variable and declare this section in vmlinux.lds.
This align sparc with most other architectures. Eventually this allow
the init_task bits to be unified across all architectures.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the array length check and fixup before copying the array.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Copy module_64.c to module.c
o Add all sparc specific bits to module.c
o delete module_32.c
o update Makefile
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Introduce a helper function
o Combine sparc64 specific case values
o add ifdef's around sparc64 code snippets
Note: The ifdef around the BUG_ON is highly questionable
but for now the safe approach was taken
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To prepare for unification use the bit neutral versions of
the Elf types defined by asm/module.h
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use some preprocessor magic in combination with the
newly introduced CONFIG_BITS to unify module.h.
A few additional symbols are added as they are needed in a follow-up patch
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_BITS is set to 32 for sparc32
and 64 for sparc64.
This allow us to use this symbol in for example header files
to ease unification of sparc32 and sparc64.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardirq.h are removed from asm-generic/local.h a few
bits fails to build. Fix these upfront.
Reported by Alexey Dobriyan.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like cpu_coregroup_map, but returns a (const) pointer.
Compile-tested on s390 (defconfig).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Like cpu_coregroup_map, but returns a (const) pointer.
Compile-tested on sparc64 (defconfig).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
