Add new device ID 0x22 and new asic generation BFI_ASIC_GEN_CT2 for 1860.
Implement FW download from user space for new Brocade HW.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add capability map and generic model name scheme for manufacturing block.
Add card types for new HW.
Remove bfa_mfg_is_card_type_valid and ibfa_mfg_adapter_prop_init_flash_ct
macros.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic to set ASIC specfic interface in IOC, HW interface initialization
APIs, mode based initialization and MSI-X resource allocation for 1860 with
no asic block. Add new h/w specific register definitions and setup registers
used by IOC logic.
Use normal kernel declaration style, c99 initializers and const for mailbox
structures. Remove unneeded parentheses.
Signed-off-by: Gurunatha Karaje <gkaraje@brocade.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to make USB-to-Ethernet-adapters (depending on usbnet) support
timestamping, the "skb_defer_rx_timestamp" and "skb_tx_timestamp" function
calls are added.
Signed-off-by: Michael Riesch <michael@riesch.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use hardcoded irq num and replace it with
FEC_IRQ_NUM macro.
Signed-off-by: Xiao Jiang <jgq516@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed that the legacy Interrupt handler didn't have the same
ECC warning as did the MSI. So this patch adds it.
Signed-off-by: Don Skidmore <donald.c.skidmore>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X540 thermal sensor interrupt isn't a General Purpose Interrupt
so doesn't need to be enabled in ixgbe_setup_gpie(). Likewise X540 doesn't
use the SDP0 for thermal sensor so it doesn't need to be enabled for any
device other than 82599.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code to enable thermal sensors for the x540 hardware, as well as a
thermal interrupt check which will exit with a critical message of a
thermal overheat is detected. Intent of code allows other mac types to
be added with different configuration in the future.
Fixed in this version is the addition of setting the temp_sensor
capable flag which was previously only set for a specific mac.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Revise high and low threshold marks wrt flow control to account
for the X540 devices and latency introduced by the loopback
switch.
Without this it was in theory possible to drop frames on a
supposedly lossless link with X540 or SR-IOV enabled.
Previously we used a magic number in a define to calculate the
threshold values. This made it difficult to sort out exactly
which latencies were or were not being accounted for. Here
I was overly explicit and tried to used #define names that would
be recognizable after reading the IEEE 802.1Qbb specification.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Disable LLI for FCoE since regular interrupt
and their moderation rate works slightly better
for FCoE also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to help cleanup the interrupt throttle rate logic by
storing the interrupt throttle rate as a value in microseconds instead of
interrupts per second. The advantage to this approach is that the value
can now be stored in an 16 bit field and doesn't require as much math to
flip the value back and forth since the hardware already used microseconds
when setting the rate.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changes to clean up the vlan rx path broke trunk vlan. Trunk vlans in
a VF driver are those set using:
"ip link set <pfdev> vf <n> <vlanid>"
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Doing an 'ifconfig ethN down' followed by an 'ifconfig ethN up' on a qemu-kvm
guest system configured with two e1000 NICs can result in an 'unable to handle
kernel paging request at 0000000100000000' or 'bad page map in process ...' or
something similar.
These result from a 4096-byte page being corrupted with the following two-word
pattern (16-bytes) repeated throughout the entire page:
0x0000000000000000
0x0000000100000000
There can be other bits set as well. What is a constant is that the 2nd word
has the 32nd bit set. So one could see:
:
0x0000000000000000
0x0000000100000000
0x0000000000000000
0x0000000172adc067 <<< bad pte
0x800000006ec60067
0x0000000700000040
0x0000000000000000
0x0000000100000000
:
Which came from from a process' page table I dumped out when the marked line
was seen as bad by print_bad_pte().
The repeating pattern represents the e1000's two-word receive descriptor:
struct e1000_rx_desc {
__le64 buffer_addr; /* Address of the descriptor's data buffer */
__le16 length; /* Length of data DMAed into data buffer */
__le16 csum; /* Packet checksum */
u8 status; /* Descriptor status */
u8 errors; /* Descriptor Errors */
__le16 special;
};
And the 32nd bit of the 2nd word maps to the 'u8 status' member, and
corresponds to E1000_RXD_STAT_DD which indicates the descriptor is done.
The corruption appears to result from the following...
. An 'ifconfig ethN down' gets us into e1000_close(), which through a number
of subfunctions results in:
1. E1000_RCTL_EN being cleared in RCTL register. [e1000_down()]
2. dma_free_coherent() being called. [e1000_free_rx_resources()]
. An 'ifconfig ethN up' gets us into e1000_open(), which through a number of
subfunctions results in:
1. dma_alloc_coherent() being called. [e1000_setup_rx_resources()]
2. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
3. E1000_RCTL_EN being cleared in RCTL register. [e1000_configure_rx()]
4. RDLEN, RDBAH and RDBAL registers being set to reflect the dma page
allocated in step 1. [e1000_configure_rx()]
5. E1000_RCTL_EN being set in RCTL register. [e1000_configure_rx()]
During the 'ifconfig ethN up' there is a window opened, starting in step 2
where the receives are enabled up until they are disabled in step 3, in which
the address of the receive descriptor dma page known by the NIC is still the
previous one which was freed during the 'ifconfig ethN down'. If this memory
has been reallocated for some other use and the NIC feels so inclined, it will
write to that former dma page with predictably unpleasant results.
I realize that in the guest, we're dealing with an e1000 NIC that is software
emulated by qemu-kvm. The problem doesn't appear to occur on bare-metal. Andy
suspects that this is because in the emulator link-up is essentially instant
and traffic can start flowing immediately. Whereas on bare-metal, link-up
usually seems to take at least a few milliseconds. And this might be enough
to prevent traffic from flowing into the device inside the window where
E1000_RCTL_EN is set.
So perhaps a modification needs to be made to the qemu-kvm e1000 NIC emulator
to delay the link-up. But in defense of the emulator, it seems like a bad idea
to enable dma operations before the address of the memory to be involved has
been made known.
The following patch no longer enables receives in e1000_setup_rctl() but leaves
them however they were. It only enables receives in e1000_configure_rx(), and
only after the dma address has been made known to the hardware.
There are two places where e1000_setup_rctl() gets called. The one in
e1000_configure() is followed immediately by a call to e1000_configure_rx(), so
there's really no change functionally (except for the removal of the problem
window. The other is in __e1000_shutdown() and is not followed by a call to
e1000_configure_rx(), so there is a change functionally. But consider...
. An 'ifconfig ethN down' (just as described above).
. A 'suspend' of the system, which (I'm assuming) will find its way into
e1000_suspend() which calls __e1000_shutdown() resulting in:
1. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
And again we've re-opened the problem window for some unknown amount of time.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for SJW user settings to not set the synchronization
jump width (SJW) to 1 in any case when using the in-kernel bittiming
calculation.
The ip-tool from iproute2 already supports to pass the user defined SJW
value. The given SJW value is sanitized with the controller specific sjw_max
and the calculated tseg2 value. As the SJW can have values up to 4 providing
this value will lead to the maximum possible SJW automatically. A higher SJW
allows higher controller oscillator tolerances.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also changes writel/readl to iowrite32/ioread32.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver for the SJA1000 based PCMCIA card 'CPC-Card' from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Markus Plessing <plessing@ems-wuensche.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most boards with SysKonnect/Marvell Ethernet have only a single port.
For the single port case, use the standard Ethernet driver convention
of allocating IRQ when device is brought up rather than at probe time.
This patch also adds some additional read after writes to avoid any
PCI posting problems when setting the IRQ mask.
The error handling of dual port cards is also changed. If second port
can not be brought up, then just fail. No point in continuing, since
the failure is most certainly because of out of memory.
It is worth noting that the dual port skge device has a single irq but two
seperate status rings and therefore has two NAPI objects, one for
each port.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix provides a newly flashed FW version (appended, in braces)
along with the currently running FW version via ethtool. The newly
flashed version runs only after a system reset.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-posting with subject fixed!
Multicast programming has been broken since commit 5b8821b7. Setting the
MULTICAST flag while sending the cmd to the FW was missing. Fixed this.
Also fixed-up some indentation in the adjacent lines.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch touchs most of the enic port profile handling code.
Tried to break it into sub patches without success.
The patch mainly does the following:
- Port profile operations for a SRIOV VF are modified to work
only via its PF
- Changes the port profile static struct in struct enic to a pointer.
This is because a SRIOV PF has to now hold the port profile information
for all its VF's
- Moved address registration for VF's during port profile ASSOCIATE time
- Most changes in port profile handling code are changes related to indexing
into the port profile struct array of a PF for the VF port profile
information
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds helper functions to use PF as proxy for SRIOV VF firmware
commands.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to enable SRIOV on enic devices. Enic SRIOV VF's are dynamic vnics and will use the same driver code as dynamic vnics.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most sky2 hardware only has a single port, although some variations of the
chip support two interfaces. For the single port case, use the standard
Ethernet driver convention of allocating IRQ when device is brought up
rather than at probe time.
Also, change the error handling of dual port cards so that if second
port can not be brought up, then just fail. No point in continuing, since
the failure is most certainly because of out of memory.
The dual port sky2 device has a single irq and a single status ring,
therefore it has a single NAPI object shared by both ports.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev is unused in pch_gbe_setup_rctl. Remove this declaration to
avoid a compiler warning.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ehea ndo_get_stats can sleep in two places, in a hcall
and in a GFP_KERNEL alloc, which is not correct.
This patch creates a delayed workqueue that grabs the information each 1
sec from the hardware, and place it into the device structure, so that,
.ndo_get_stats quickly returns the device structure statistics block.
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds one step support to the phyter. When enabled, the
hardware does not provide time stamps for transmitted sync messages but
instead inserts the stamp into the outgoing packet.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables six external event channels and one periodic output.
One GPIO is reserved for synchronizing multiple PHYs. The assignment
of GPIO functions can be changed via a module parameter.
The code supports multiple simultaneous events by inducing a PTP clock
event for every channel marked in the PHY's extended status word.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Argument list to CDRP function has become unmanageably long. Fix it by properly
declaring a struct that encompasses all the input and output parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ameen Rahman <ameen.rahman@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The imx6q enet is a derivative of imx28 enet controller. It fixed
the frame endian issue found on imx28, and added 1 Gbps support.
It also fixes a typo on vendor name in Kconfig.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function fec_enet_mii_init(), it uses non-zero pdev->id as part
of the condition to check the second fec instance (fec1). This works
before the driver supports device tree probe. But in case of device
tree probe, pdev->id is -1 which is also non-zero, so the logic becomes
broken when device tree probe gets supported.
The patch change the logic to check "pdev->id > 0" as the part of the
condition for identifying fec1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC can work without a phy reset on some platforms, which means not
very platform necessarily have a phy-reset gpio encoded in device tree.
Even on the platforms that have the gpio, FEC can work without
resetting phy for some cases, e.g. boot loader has done that.
So it makes more sense to have the phy-reset-gpio request failure as
a debug message rather than a warning, and get fec_reset_phy() return
void since the caller does not check the return anyway.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish conversion to unified ethtool ops: convert get_flags.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SEEQ drivers should depend on HAS_IOMEM to prevent compile breakage
on !HAS_IOMEM architectures:
drivers/net/ethernet/seeq/seeq8005.c: In function 'seeq8005_probe1':
drivers/net/ethernet/seeq/seeq8005.c:179:2: error:
implicit declaration of function 'inw' [-Werror=implicit-function-declaration]
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reloading FW during resets can cause issues. Remove the full reset
as it is not needed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for WOL as determined by the EEPROM.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to avoid a hardware lockup when Tx work is still
pending and we request a reset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for configuring the priority to
traffic class mapping.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need SFP+ plugable support for X540 hardware (copper only) so
don't enable the SFP+ interrupts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The DCB CEE command set_state() will complete successfully
but is misleading because it enables IEEE mode. After
this patch the command is failed.
And IEEE PFC/ETS is managed from ieee paths now instead
of using CEE primitives.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the PCI device flag indicating if a VF is assigned to a guest VM
to guard against destroying VFs upon driver removal. Implement
additional feature to detect if VFs already exist when the driver
is loaded and if so configure them and set the driver state to
SR-IOV enabled.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
