Rüdiger found a bug in nv_open that explains some of the reports
with duplex mismatches:
nv_open calls nv_update_link_speed for initializing the hardware link speed
registers. If current link setting matches the values in np->linkspeed and
np->duplex, then the function does nothing.
Usually, doing nothing is the right thing, but not in nv_open: During
nv_open, the registers must be initialized because the nic was reset.
The attached patch fixes that by setting np->linkspeed to an invalid value
before calling nv_update_link_speed from nv_open.
Signed-Off-By: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The DM9000 driver is responding to ioctl() calls it should not be. This
can cause problems with the wireless tools incorrectly indentifying the
device as wireless capable, and crashing under certain operations.
This patch also moves the version printk() to the init call, so that
you only get it once for multiple devices, and to show it is loaded
if there are no defined dm9000s
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix DM9000 driver usage of spinlocks, which mainly came to light
when running a kernel with spinlock debugging. These come down to:
1) Un-initialised spin lock
2) Several cases of using spin_xxx(lock) and not spin_xxx(&lock)
3) move the locking around the phy reg for read/write to only
keep the lock when actually reading or writing to the phy.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
After suspend the driver needs to retest link status in case the cable
has been inserted or removed during the suspend.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Using the right register clearly improves chances of getting the MII
code and thus the driver working at all.
- On startup check the media type before setting up duplex or we might
spend the first 1.2s with a wrong duplex setting.
- Get rid of whitespace lines.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
BCM5785 (HT1000) is a Opteron Southbridge from Serverworks/Broadcom that
incorporates a single channel ATA100 IDE controller that is functionally
identical to the Serverworks CSB6 IDE controller. This patch adds support
for the new PCI device ID and also the support for this controller.
Signed-off-by: Narendra Sankar <nsankar@broadcom.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
Adds support for Netcell Revolution to pci-ide generic driver by including
it in the list of devices matched. Includes the Revolution in the list of
simplex devices forced into DMA mode.
Signed-off-by: Matt Gillette <matt.gillette@netcell.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
drivers/ide/ppc/pmac.c uses symbols ide_build_sglist,
__ide_dma_off_quietly, __ide_dma_on and __ide_dma_timeout when
CONFIG_BLK_DEV_IDEDMA_PMAC is defined. The declarations for these
symbols (in ide.h) depend on CONFIG_BLK_DEV_IDEDMA_PCI. There is a
missing dependency for this in drivers/ide/Kconfig which causes
drivers/ide/ppc/pmac.c to fail to build if CONFIG_BLK_DEV_IDEDMA_PMAC
is selected but CONFIG_BLK_DEV_IDEDMA_PCI is not.
Signed-off-by: Juha-Matti Tapio <jmtapio@verkkotelakka.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
* IDEFLOPPY_TICKS_DELAY assumed HZ == 100, fix it
* increase the delay to 50ms (to match comment in the code)
Thanks to Manfred Scherer <manfred.scherer.mhm@t-online.de>
for reporting the problem and testing the patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@elka.pw.edu.pl>
... otherwise we might try to load a bitmap from an array which hasn't one.
The bug is that if you create an array with an internal bitmap, shut it down,
and then create an array with the same md device, the md drive will assume it
should have a bitmap too. As the array can be created with a different md
device, it is mostly an inconvenience. I'm pretty sure there is no risk of
data corruption.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The error path in pnp_request_card_device() is broken (one variable is
left initialized and the semaphore is not unlocked).
This fixes it (and has been tested).
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix for manual binding of drivers to devices. Problem is if you pass in
a valid device id, but the driver refuses to bind. Infinite loop as
write() tries to resubmit the data it just sent.
Thanks to Michal Ostrowski <mostrows@watson.ibm.com> for pointing the
problem out.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On the 6700/6702 PXH part, a MSI may get corrupted if an ACPI hotplug
driver and SHPC driver in MSI mode are used together.
This patch will prevent MSI from being enabled for the SHPC as part of
an early pci quirk, as well as on any pci device which sets the no_msi
bit.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This moves the code to free devt_attr from class_device_del() to
class_dev_release() which is called after the last reference to the
corresponding kobject() is gone.
This allows us to keep the devt_attr alive while the corresponding
sysfs file is open.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The flush threshold in the MAC chip should be increased.
Found while reviewing vendor version of sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Some versions of the Marvell yukon generate bogus sensor warning interrupts.
The driver would flood log with these messages. Handle this situation
cleanly by masking away at boot time.
Fixes: http://bugs.gentoo.org/show_bug.cgi?id=87182
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
drivers/net/skge.c | 24 ++++++++++--------------
drivers/net/skge.h | 8 ++++++--
2 files changed, 16 insertions(+), 16 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When both platform-specific and generic drivers exist,
enable generic over-ride with "acpi_generic_hotkey".
http://bugzilla.kernel.org/show_bug.cgi?id=4953
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reported by: Pavel Kysilka (Bugzilla Bug 5059)
The intelfb driver does not keep resolution set with fbset after
switching to anot console and back.
Steps to reproduce:
initial options: tty1,tty2 - 1024x768-60
1) tty1 - fbset after booting (1024x768-60)
2) tty1 - fbset 800x600-100
tty1: 800x600-100
3) swith to tty2, swith to tty1
tty1: 1024x768-60 (the same resolution as default from kernel booting)
This bug is caused by intelfb unintentionally destroying info->flags in
set_par(). Therefore the flag, FBINFO_MISC_USEREVENT used to notify
fbcon of a mode change was cleared causing the above problem. This bug
though is not intelfb specific, as other drivers may also be affected.
The fix is to save info->flags in a local variable before calling any
of the driver hooks. A more definitive fix (for post 2.6.13) is to
separate info->flags into one that is set by the driver and another that
is set by core fbdev/fbcon.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Pavel Kysilka (Bugzilla Bug 4738)
modprobe of intelfb results in the following error message:
intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G chi
intelfb: Version 0.9.2
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
allocation failed: out of vmalloc space - use vmalloc=<size> to increase siz
intelfb: Cannot remap FB region.
This will fail if the graphics aperture size is greater than 128 MB.
Fix is to ioremap only from the beginning of graphics aperture to the
end of the used framebuffer memory.
Signed-off-by: Sylvain Meyer <sylvain.meyer@worldonline.fr>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This reverts commits
71db63acff
[PATCH] increase PCIBIOS_MIN_IO on x86
and
0b2bfb4e7f
ACPI: increase PCIBIOS_MIN_IO on x86
since Lukas Sandströ<lukass@etek.chalmers.se> reports that this breaks
his on-board nvidia audio.
We should re-visit this later. For now we revert the change
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It introduces a repeatable oops in the driver, which is a bigger problem
than the patch tries to solve. From the original description:
Author: Jamie Lenehan <lenehan@twibble.org>
Date: Thu Mar 3 14:41:40 2005 +0200
[PATCH] dc395x: Fix support for highmem
From: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Removes the page_to_virt and maps sg lists dynamically.
This makes the driver work with highmem pages.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This leaves the issue of whether we should deprecate the whole thing (or
if we should check the whole mmap range, for that matter) open. Just do
the minimal fix for now.
Do not spam syslog each 10 seconds when there is nothing on the wire.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Suggested by Steven Rostedt, matches his patch included in e100.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redefined buffer_info-dma to be dma_addr_t instead of uint64
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Remove unused functions, render some variable static instead of global - based on patch from Adrian Bunk
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Ethtool cleanup patch from Stephen Hemminger
* use ADVERTISED_xxx fields when setting advertised fields
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix data output by ethtool -d
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use netdev_priv() instead of netdev->priv
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix unnecessary link state messages
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Set RXDCTL:PTHRESH/HTHRESH to zero
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Manfred Spraul