Krzysztof found some old cyrix cpu where an mtrr-alike cpu feature was
not detected properly.
this one is based on Krzysztof' patch, and we call ->c_identify() in
early_identify_cpu.
need to call c_identify() for cpus without cpuid even earlier ...
v2: Krzysztof point out need to give cyrix another chance about cpuid
checking again, after ->c_identify() enables cpuid for it
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Russ Anderson reported a boot crash with EFI and latest mainline:
BIOS-e820: 00000000fffa0000 - 00000000fffac000 (reserved)
Pid: 0, comm: swapper Not tainted 2.6.27-rc5-00100-gec0c15a-dirty #5
Call Trace:
[<ffffffff80849195>] early_idt_handler+0x55/0x69
[<ffffffff80313e52>] __memcpy+0x12/0xa4
[<ffffffff80859015>] efi_init+0xce/0x932
[<ffffffff80869c83>] setup_early_serial8250_console+0x2d/0x36a
[<ffffffff80238688>] __insert_resource+0x18/0xc8
[<ffffffff8084f6de>] setup_arch+0x3a7/0x632
[<ffffffff808499ed>] start_kernel+0x91/0x367
[<ffffffff80849393>] x86_64_start_kernel+0xe3/0xe7
[<ffffffff808492b0>] x86_64_start_kernel+0x0/0xe7
RIP 0x10
Such a crash is possible if the CPU in this system is a 64-bit
processor which doesn't support NX (ie, old Intel P4 -based64-bit
processors).
Certainly, if we support such processors, then we should start with
_PAGE_NX initially clear in __supported_pte_flags, and then set it once
we've established that the processor does indeed support NX. That will
prevent early_ioremap - or anything else - from trying to set it.
The simple fix is to simply call check_efer() earlier.
Reported-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As well as discard fake accessed bit and dirty bit of EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Accesses to CR4 are intercepted even with Nested Paging enabled. But the code
does not check if the guest wants to do a global TLB flush. So this flush gets
lost. This patch adds the check and the flush to svm_set_cr4.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch introduces a guest TLB flush on every NPF exit in KVM. This fixes
random segfaults and #UD exceptions in the guest seen under some workloads
(e.g. long running compile workloads or tbench). A kernbench run with and
without that fix showed that it has a slowdown lower than 0.5%
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Error handling code following a kmalloc should free the allocated data.
Note that at the point of the change, node has not yet been stored in d, so
it is not affected by the existing cleanup code.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,l;
position p1,p2;
expression *ptr != NULL;
@@
(
if ((x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...)) == NULL) S
|
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
)
<... when != x
when != if (...) { <+...x...+> }
x->f = E
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The hardware virtualization technology evolves very fast. But currently
it's hard to tell if your CPU support a certain kind of HW technology
without digging into the source code.
The patch add a new catagory in "flags" under /proc/cpuinfo. Now "flags"
can indicate the (important) HW virtulization features the CPU supported
as well.
Current implementation just cover Intel VMX side.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
They are hardware specific MSRs, and we would use them in virtualization
feature detection later.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make handle_signal() same as 32bit.
No change in functionality intended.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
restore_i387_xstate() is declared as:
int restore_i387_xstate(void __user *buf);
so, make the variable buf void __user *.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
clean up and make signal_fault() same as 32bit.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
consolidate the code some more.
No change in functionality intended.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
now that arch/x86/kernel/cpu/intel_64.c and
arch/x86/kernel/cpu/intel.c are equal, drop
arch/x86/kernel/cpu/intel_64.c and fix up
the glue.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
No change in functionality intended - this only adds the 32-bit side.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On 32-bit, at least the generic nops are fairly reasonable, but the
default nops for 64-bit really look pretty sad, and the P6 nops really do
look better.
So I would suggest perhaps moving the static P6 nop selection into the
CONFIG_X86_64 thing.
The alternative is to just get rid of that static nop selection, and just
have two cases: 32-bit and 64-bit, and just pick obviously safe cases for
them.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Right now, there is no notifier that is called on a new cpu, before the new
cpu begins processing interrupts/softirqs.
Various kernel function would need that notification, e.g. kvm works around
by calling smp_call_function_single(), rcu polls cpu_online_map.
The patch adds a CPU_STARTING notification. It also adds a helper function
that sends the message to all cpu_chain handlers.
Tested on x86-64.
All other archs are untested. Especially on sparc, I'm not sure if I got
it right.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Non real IOMMU implemenations (which doesn't do virtual mappings,
e.g. swiotlb, pci-nommu, etc) need to use proper gfp flags and
dma_mask to allocate pages in their own dma_alloc_coherent()
(allocated page need to be suitable for device's coherent_dma_mask).
This patch makes dma_alloc_coherent do this job so that IOMMUs don't
need to take care of it any more.
Real IOMMU implemenataions can simply ignore the gfp flags.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We need to use __GFP_DMA for NULL device argument (fallback_dev) with
pci-nommu. It's a hack for ISA (and some old code) so we need to use
GFP_DMA.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The check to see if dev->dma_mask is NULL in pci-nommu is more
appropriate for dma_alloc_coherent().
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/cpu/amd.c is now 100% identical to
arch/x86/kernel/cpu/amd_64.c, so use amd.c on 64-bit too
and fix up the namespace impact.
Simplify the Kconfig glue as well.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
1. make 32bit have early_init_amd_mc and amd_detect_cmp
2. seperate init_amd_k5/k6/k7 ...
v2: fix compiling for !CONFIG_SMP
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_init(): fix memory leak when using CPU hotplug
x86: pda_init(): fix memory leak when using CPU hotplug
x86, xen: Use native_pte_flags instead of native_pte_val for .pte_flags
x86: move mtrr cpu cap setting early in early_init_xxxx
x86: delay early cpu initialization until cpuid is done
x86: use X86_FEATURE_NOPL in alternatives
x86: add NOPL as a synthetic CPU feature bit
x86: boot: stub out unimplemented CPU feature words
Exception stacks are allocated each time a CPU is set online.
But the allocated space is never freed. Thus with one CPU hotplug
offline/online cycle there is a memory leak of 24K (6 pages) for
a CPU.
Fix is to allocate exception stacks only once -- when the CPU is
set online for the first time.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
pda->irqstackptr is allocated whenever a CPU is set online.
But it is never freed. This results in a memory leak of 16K
for each CPU offline/online cycle.
Fix is to allocate pda->irqstackptr only once.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: akpm@linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Using native_pte_val triggers the BUG_ON() in the paravirt_ops
version of pte_flags().
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Krzysztof Helt found MTRR is not detected on k6-2
root cause:
we moved mtrr_bp_init() early for mtrr trimming,
and in early_detect we only read the CPU capability from cpuid,
so some cpu doesn't have that bit in cpuid.
So we need to add early_init_xxxx to preset those bit before mtrr_bp_init
for those earlier cpus.
this patch is for v2.6.27
Reported-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move early cpu initialization after cpu early get cap so the
early cpu initialization can fix up cpu caps.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Bring signal number conversion in __setup_frame() and __setup_rt_frame()
up into the common part setup_frame().
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make setup_rt_frame() and split out frame setups from handle_signal().
This is for cosmetic unification of handle_signal().
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use asm/syscall.h interfaces that do the same things.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After fixing the u32 thinko I sill had occasional hickups on ATI chipsets
with small deltas. There seems to be a delay between writing the compare
register and the transffer to the internal register which triggers the
interrupt. Reading back the value makes sure, that it hit the internal
match register befor we compare against the counter value.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We use the HPET only in 32bit mode because:
1) some HPETs are 32bit only
2) on i386 there is no way to read/write the HPET atomic 64bit wide
The HPET code unification done by the "moron of the year" did
not take into account that unsigned long is different on 32 and
64 bit.
This thinko results in a possible endless loop in the clockevents
code, when the return comparison fails due to the 64bit/332bit
unawareness.
unsigned long cnt = (u32) hpet_read() + delta can wrap over 32bit.
but the final compare will fail and return -ETIME causing endless
loops.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use X86_FEATURE_NOPL to determine if it is safe to use P6 NOPs in
alternatives. Also, replace table and loop with simple if statement.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The long noops ("NOPL") are supposed to be detected by family >= 6.
Unfortunately, several non-Intel x86 implementations, both hardware
and software, don't obey this dictum. Instead, probe for NOPL
directly by executing a NOPL instruction and see if we get #UD.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The CPU feature detection code in the boot code is somewhat minimal,
and doesn't include all possible CPUID words. In particular, it
doesn't contain the code for CPU feature words 2 (Transmeta),
3 (Linux-specific), 5 (VIA), or 7 (scattered). Zero them out, so we
can still set those bits as known at compile time; in particular, this
allows creating a Linux-specific NOPL flag and have it required (and
therefore resolvable at compile time) in 64-bit mode.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Some BIOSes (the Intel DG33BU, for example) wrongly claim to have DMAR
when they don't. Avoid the resulting crashes when it doesn't work as
expected.
I'd still be grateful if someone could test it on a DG33BU with the old
BIOS though, since I've killed mine. I tested the DMI version, but not
this one.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch adds the detection of the northbridges in the AMD family 0x11
processors. It also fixes the magic numbers there while changing this code.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Additional updates to the x86 defconfigs. The goals are, as before:
- Make them usable to testers, more so than distributors or end users,
both of which are likely to have their own config already.
- Keep 32 and 64 bits as similar as is practical.
Changes:
- Use a more generic CPU type (ppro and generic, respectively).
- Bump number of CPUs to 64 (few if any NR_CPUS arrays left).
- Enable PAT.
- Enable OPTIMIZE_INLINE.
- Enable microcode update support.
- Build SMT scheduler support (in addition to MC).
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
They were already called once in arch/x86/kernel/setup.c - we don't need to call them again.
Signed-off-by: Alex Nixon <alex.nixon@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The CPA test code uses _PAGE_UNUSED1, so make sure its obvious.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The minimum reprogramming delta was hardcoded in HPET ticks,
which is stupid as it does not work with faster running HPETs.
The C1E idle patches made this prominent on AMD/RS690 chipsets,
where the HPET runs with 25MHz. Set it to 5us which seems to be
a reasonable value and fixes the problems on the bug reporters
machines. We have a further sanity check now in the clock events,
which increases the delta when it is not sufficient.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Tested-by: Dmitry Nezhevenko <dion@inhex.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use cpu/common.c on both 64-bit and 32-bit and remove cpu/common_64.c.
We started out with this linecount:
816 arch/x86/kernel/cpu/common_64.c
805 arch/x86/kernel/cpu/common.c
and the resulting common.c is 1197 lines long, so there's already
424 lines of code eliminated in this phase of the unification.
Signed-off-by: Yinghai <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge leftover whitespaces, to make arch/x86/kernel/cpu/common_64.c
exactly identical to arch/x86/kernel/cpu/common.c.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
hard to merge by lines... (as here we have material differences between
32-bit and 64-bit mode) - will try to do it later.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move the 32-bit and 64-bit gdt_page definitions next to each
other, separated with an #ifdef.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Make the files more similar in preparation to unification, no
code changed.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit has X86_HT set too, so use that instead of SMP.
This also removes a include/asm-x86/processor.h ifdef.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce a fast TSC-calibration method on sane hardware.
It only uses 17920 PIT timer ticks to calibrate the TSC, plus 256 ticks on
each side to make sure the TSC values were very close to the tick, so the
whole calibration takes 15ms. Yet, despite only takign 15ms,
we can actually give pretty stringent guarantees of accuracy:
- the code requires that we hit each 256-counter block at least 50 times,
so the TSC error is basically at *MOST* just a few PIT cycles off in
any direction. In practice, it's going to be about one microseconds
off (which is how long it takes to read the counter)
- so over 17920 PIT cycles, we can pretty much guarantee that the
calibration error is less than one half of a percent.
My testing bears this out: on my machine, the quick-calibration reports
2934.085kHz, while the slow one reports 2933.415.
Yes, the slower calibration is still more precise. For me, the slow
calibration is stable to within about one hundreth of a percent, so it's
(at a guess) roughly an order-and-a-half of magnitude more precise. The
longer you wait, the more precise you can be.
However, the nice thing about the fast TSC PIT synchronization is that
it's pretty much _guaranteed_ to give that 0.5% precision, and fail
gracefully (and very quickly) if it doesn't get it. And it really is
fairly simple (even if there's a lot of _details_ there, and I didn't get
all of those right ont he first try or even the second ;)
The patch says "110 insertions", but 63 of those new lines are actually
comments.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
---
arch/x86/kernel/tsc.c | 111 ++++++++++++++++++++++++++++++++++++++++++++++++-
1 files changed, 110 insertions(+), 1 deletions(-)
1. add c_x86_vendor into cpu_dev
2. change cpu_devs to static
3. check c_x86_vendor before put that cpu_dev into array
4. remove alignment for 64bit
5. order the sequence in cpu_devs according to link sequence...
so could put intel at first, then amd...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
v2: make 64 bit get c->x86_cache_alignment = c->x86_clfush_size
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
1. add extended_cpuid_level for 32bit
2. add generic_identify for 64bit
3. add early_identify_cpu for 32bit
4. early_identify_cpu not be called by identify_cpu
5. remove early in get_cpu_vendor for 32bit
6. add get_cpu_cap
7. add cpu_detect for 64bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move early cpu initialization after cpu early get cap so the
early cpu initialization can fix up cpu caps.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Krzysztof Helt found MTRR is not detected on k6-2
root cause:
we moved mtrr_bp_init() early for mtrr trimming,
and in early_detect we only read the CPU capability from cpuid,
so some cpu doesn't have that bit in cpuid.
So we need to add early_init_xxxx to preset those bit before mtrr_bp_init
for those earlier cpus.
this patch is for v2.6.27
Reported-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
try to insert_resource second time, by expanding the resource...
for case: e820 reserved entry is partially overlapped with bar res...
hope it will never happen
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: aestetic
Capitalize function call interrupts consistently.
All other descriptions in /proc/interrupts are capitalized except
for "function call interrupts". Capitalize it too for consistency.
While that's technically a published ABI I think the risk of anyone
relying on that text to stay the same is negligible.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: performance optimization
I did some rebenchmarking with modern compilers and dropping
-funroll-loops makes the function consistently go faster by a few
percent. So drop that flag.
Thanks to Richard Guenther for a hint.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
this one replaces:
| commit a2bd7274b4
| Author: Yinghai Lu <yhlu.kernel@gmail.com>
| Date: Mon Aug 25 00:56:08 2008 -0700
|
| x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3
v2: insert e820 reserve resources before pnp_system_init
v3: fix merging problem in tip/x86/core
v4: address Linus's review about comments and condition in _late()
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so could let BAR res register at first, or even pnp.
v2: insert e820 reserve resources before pnp_system_init
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The last changes made the calibration loop 250ms long which is far
too much. Try to do that more clever.
Experiments have shown that using a 10ms delay for the PIT based calibration
gives us a good enough value. If we have a reference (HPET/PMTIMER) and the
result of the PIT and the reference is close enough, then we can break out of
the calibration loop on a match right away and use the reference value.
Otherwise we just loop 3 times and decide then, which value to take.
One caveat is that for virtualized environments the PIT calibration often does
not work at all and I found out that 10us is a bit too short as well for the
reference to give a sane result. The solution here is to make the last loop
longer when the first two PIT calibrations failed.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When calibration against PIT fails, the warning that we print is misleading.
In a virtualized environment the VM may get descheduled while calibration
or, the check in PIT calibration may fail due to other virtualization
overheads.
The warning message explicitly assumes that calibration failed due to SMI's
which may not be the case. Change that to something proper.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Manually adding "io_delay=0xed" fixes system lockups in ioapic
mode on this machine.
System Information
Manufacturer: Hewlett-Packard
Product Name: Presario F700 (KA695EA#ABF)
Base Board Information
Manufacturer: Quanta
Product Name: 30D3
Reference:
https://bugzilla.redhat.com/show_bug.cgi?id=459546
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The TSC calibration function is still very complicated, but this makes
it at least a little bit less so by moving the PIT part out into a
helper function of its own.
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-of-by: Linus Torvalds <torvalds@linux-foundation.org>
Larry Finger reported at http://lkml.org/lkml/2008/9/1/90:
An ancient laptop of mine started throwing errors from b43legacy when
I started using 2.6.27 on it. This has been bisected to commit bfc0f59
"x86: merge tsc calibration".
The unification of the TSC code adopted mostly the 64bit code, which
prefers PMTIMER/HPET over the PIT calibration.
Larrys system has an AMD K6 CPU. Such systems are known to have
PMTIMER incarnations which run at double speed. This results in a
miscalibration of the TSC by factor 0.5. So the resulting calibrated
CPU/TSC speed is half of the real CPU speed, which means that the TSC
based delay loop will run half the time it should run. That might
explain why the b43legacy driver went berserk.
On the other hand we know about systems, where the PIT based
calibration results in random crap due to heavy SMI/SMM
disturbance. On those systems the PMTIMER/HPET based calibration logic
with SMI detection shows better results.
According to Alok also virtualized systems suffer from the PIT
calibration method.
The solution is to use a more wreckage aware aproach than the current
either/or decision.
1) reimplement the retry loop which was dropped from the 32bit code
during the merge. It repeats the calibration and selects the lowest
frequency value as this is probably the closest estimate to the real
frequency
2) Monitor the delta of the TSC values in the delay loop which waits
for the PIT counter to reach zero. If the maximum value is
significantly different from the minimum, then we have a pretty safe
indicator that the loop was disturbed by an SMI.
3) keep the pmtimer/hpet reference as a backup solution for systems
where the SMI disturbance is a permanent point of failure for PIT
based calibration
4) do the loop iteration for both methods, record the lowest value and
decide after all iterations finished.
5) Set a clear preference to PIT based calibration when the result
makes sense.
The implementation does the reference calibration based on
HPET/PMTIMER around the delay, which is necessary for the PIT anyway,
but keeps separate TSC values to ensure the "independency" of the
resulting calibration values.
Tested on various 32bit/64bit machines including Geode 266Mhz, AMD K6
(affected machine with a double speed pmtimer which I grabbed out of
the dump), Pentium class machines and AMD/Intel 64 bit boxen.
Bisected-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Breaking lines due to some imaginary problem with a long line length is
often stupid and wrong, but never more so when it splits a string that
is printed out into multiple lines. This really ended up making it much
harder to find where some error strings were printed out, because a
simple 'grep' didn't work.
I'm sure there is tons more of this particular idiocy hiding in other
places, but this particular case hit me once more last week. So fix it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit a2bd7274b4.
It wasn't really right to begin with (there's a better fix for the
problem with e820 reservations clashing with PCI BAR's pending), but it
also actually causes more regressions, so it should be reverted even
before the better fix is finalized.
Rafael reports that this commit broke AHCI detection, and thus causes
the kernel to not boot on his quad core test box.
Reported-and-bisected-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: David Witbrodt <dawitbro@sbcglobal.net>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
From NHM processor onward, Intel processors can support hardware accelerated
CRC32c algorithm with the new CRC32 instruction in SSE 4.2 instruction set.
The patch detects the availability of the feature, and chooses the most proper
way to calculate CRC32c checksum.
Byte code instructions are used for compiler compatibility.
No MMX / XMM registers is involved in the implementation.
Signed-off-by: Austin Zhang <austin.zhang@intel.com>
Signed-off-by: Kent Liu <kent.liu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Make poll_idle() behave more like the other idle methods.
Currently, poll_idle() returns immediately. The other
idle methods all wait indefinately for some condition
to come true before returning. poll_idle should emulate
these other methods and also wait for a return condition,
in this case, for need_resched() to become 'true'.
Without this delay the idle loop spends all of its time
in the outer loop that calls poll_idle. This outer loop,
these days, does real work, some of it under rcu locks.
That work should only be done when idle is entered and
when idle exits, not continuously while idle is spinning.
Signed-off-by: Joe Korty <joe.korty@ccur.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have had a number of cases where <asm/cpufeature.h> (and its
predecessors) have diverged substantially from the names list in
/proc/cpuinfo. This patch generates the latter from the former.
It retains the option for explicitly overriding the strings, but by
making that require a separate action it should at least be less
likely to happen.
It would be good to do a future pass and rename strings that are
gratuituously different in the kernel (/proc/cpuinfo is a userspace
interface and must remain constant.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add the missing XCR0(XFEATURE_ENABLED_MASK) restore during resume.
Reported-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
acpi_mcfg_64bit_base_addr is used when CONFIG_PCI_MMCONFIG is enabled.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Enable some option commonly used by testers in defconfig, including
some very common device drivers and network boot support. defconfig
is still not meant to be a kitchen-sink configuration.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove an unnecessary level of abstraction in the msr-on-cpu library.
Although this duplicates some code, the duplicated code is less than
the additional code, and this way should be faster.
Additionally, change the order of the functions to make the regular
structure of this file more obvious.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Return the correct return value when the CPUID driver partially
completes a request (we should return the number of bytes actually
read or written, instead of the error code.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Return the correct return value when the MSR driver partially
completes a request (we should return the number of bytes actually
read or written, instead of the error code.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Propagate error (-ENXIO) from smp_call_function_single() in the CPUID
driver. This can happen when a CPU is unplugged while the CPUID
driver is open.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Propagate error (-ENXIO) from smp_call_function_single(). These
errors can happen when a CPU is unplugged while the MSR driver is
open.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This fixes a regression that was indirectly caused by commit
1184dc2ffe ("x86: modify Kconfig to allow
up to 4096 cpus").
Allowing 4k CPU's is not practical at this time, because we still have a
number of places that have several 'cpumask_t's on the stack, and a
4k-bit cpumask is 512 bytes of stack-space for each such variable. This
literally caused functions like 'smp_call_function_mask' to have a 2.5kB
stack frame, and several functions to have 2kB stackframes.
With an 8kB stack total, smashing the stack was simply much too likely.
At least bugzilla entry
http://bugzilla.kernel.org/show_bug.cgi?id=11342
was due to this.
The earlier commit to not inline load_module() into sys_init_module()
fixed the particular symptoms of this that Alan Brunelle saw in that
bugzilla entry, but the huge stack waste by cpumask_t's was the more
direct cause.
Some day we'll have allocation helpers that allocate large CPU masks
dynamically, but in the meantime we simply cannot allow cpumasks this
large.
Cc: Alan D. Brunelle <Alan.Brunelle@hp.com>
Cc: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: add X86_FEATURE_XMM4_2 definitions
x86: fix cpufreq + sched_clock() regression
x86: fix HPET regression in 2.6.26 versus 2.6.25, check hpet against BAR, v3
x86: do not enable TSC notifier if we don't need it
x86 MCE: Fix CPU hotplug problem with multiple multicore AMD CPUs
x86: fix: make PCI ECS for AMD CPUs hotplug capable
x86: fix: do not run code in amd_bus.c on non-AMD CPUs
The shadow code assigns a pte directly in one place, which is nonatomic on
i386 can can cause random memory references. Fix by using an atomic setter.
Signed-off-by: Avi Kivity <avi@qumranet.com>
I noticed that my sched_clock() was slow on a number of machine, so I
started looking at cpufreq.
The below seems to fix the problem for me.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Triple-fault and keyboard reset may assert INIT instead of RESET; however
INIT is blocked when Intel VT is enabled. This leads to a partially reset
machine when invoking emergency_restart via sysrq-b: the processor is still
working but other parts of the system are dead.
Default to rebooting via ACPI, which correctly asserts RESET and reboots the
machine.
This is safe since we will fall back to keyboard reset and triple fault if
acpi is not enabled or if the reset is not successful.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
David Witbrodt tracked down (and bisected) a hpet bootup hang on his
system to the following problem: a BIOS bug made the hpet device
visible as a generic PCI device. If e820 reserved entries happen to
be registered first in the resource tree [which v2.6.26 started doing],
then the PCI code will reallocate that device's BAR to some other
address - breaking timer IRQs and hanging the system.
( Normally hpet devices are hidden by the BIOS from the OS's PCI
discovery via chipset magic. Sometimes the hpet is not a PCI device
at all. )
Solve this fundamental fragility by making non-PCI platform drivers
insert resources into the resource tree even if it overlaps the e820
reserved entry, to keep the resource manager from updating the BAR.
Also do these checks for the ioapic and mmconfig addresses, and emit
a warning if this happens.
Bisected-by: David Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: David Witbrodt <dawitbro@sbcglobal.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: crash on non-TSC-equipped CPUs
Don't enable the TSC notifier if we *either*:
1. don't have a CPU, or
2. have a CPU with constant TSC.
In either of those cases, the notifier is either damaging (1) or useless(2).
From: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During CPU hot-remove the sysfs directory created by
threshold_create_bank(), defined in
arch/x86/kernel/cpu/mcheck/mce_amd_64.c, has to be removed before
its parent directory, created by mce_create_device(), defined in
arch/x86/kernel/cpu/mcheck/mce_64.c . Moreover, when the CPU in
question is hotplugged again, obviously the latter has to be created
before the former. At present, the right ordering is not enforced,
because all of these operations are carried out by CPU hotplug
notifiers which are not appropriately ordered with respect to each
other. This leads to serious problems on systems with two or more
multicore AMD CPUs, among other things during suspend and hibernation.
Fix the problem by placing threshold bank CPU hotplug callbacks in
mce_cpu_callback(), so that they are invoked at the right places,
if defined. Additionally, use kobject_del() to remove the sysfs
directory associated with the kobject created by
kobject_create_and_add() in threshold_create_bank(), to prevent the
kernel from crashing during CPU hotplug operations on systems with
two or more multicore AMD CPUs.
This patch fixes bug #11337.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Andi Kleen <andi@firstfloor.org>
Tested-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
use x2apic id reported by cpuid during topology discovery, instead of the
apic id configured in the APIC. For most of the systems, x2apic id
reported by cpuid leaf 0xb will be same as the physical apic id reported
by the APIC_ID register of the APIC. We follow the suggested guidelines
and use the apic id reported by the cpuid.
No change to non-generic UV platforms, will use the apic id reported in the
APIC_ID register as the cpuid reported apic id's may not be unique.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpuid leaf 0xb provides extended topology enumeration. This interface provides
the 32-bit x2APIC id of the logical processor and it also provides a new
mechanism to detect SMT and core siblings (which provides increased
addressability).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Beulich wrote:
> Even worse - this would even try to access the MSR on non-AMD CPUs
> (currently probably prevented just by the fact that only AMD ones use
> family values of 0x10 or higher).
This patch adds cpu vendor check to the postcore_initcalls.
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the start addr for free_memtype calls in the error path.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Acked-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: work around MTRR mask setting, v2
x86: fix section mismatch warning - uv_cpu_init
x86: fix VMI for early params
x86: fix two modpost warnings in mm/init_64.c
x86: fix 1:1 mapping init on 64-bit (memory hotplug case)
x86: work around MTRR mask setting
x86: PAT Update validate_pat_support for intel CPUs
devmem, x86: PAT Change /dev/mem mmap with O_SYNC to use UC_MINUS
x86: PAT proper tracking of set_memory_uc and friends
x86: fix BUG: unable to handle kernel paging request (numaq_tsc_disable)
x86: export pv_lock_ops non-GPL
x86, mmiotrace: silence section mismatch warning - leave_uniprocessor
x86: use WARN() in arch/x86/kernel
x86: use WARN() in arch/x86/mm/ioremap.c
werror: fix pci calgary
x86: fix oprofile + hibernation badness
x86, SGI UV: hardcode the TLB flush interrupt system vector
x86: fix Xorg startup/shutdown slowdown with PAT
x86: fix "kernel won't boot on a Cyrix MediaGXm (Geode)"
x86 iommu: remove unneeded parenthesis
improve the debug printout:
- make it actually display something
- print it only once
would be nice to have a WARN_ONCE() facility, to feed such things to
kerneloops.org.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
WARNING: vmlinux.o(.cpuinit.text+0x3cc4): Section mismatch in reference from the function uv_cpu_init() to the function .init.text:uv_system_init()
The function __cpuinit uv_cpu_init() references
a function __init uv_system_init().
If uv_system_init is only used by uv_cpu_init then
annotate uv_system_init with a matching annotation.
uv_system_init was ment to be called only once, so do it from codepath
(native_smp_prepare_cpus) which is called once, right before activation
of other cpus (smp_init).
Note: old code relied on uv_node_to_blade being initialized to 0,
but it'a not initialized from anywhere.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
alloc_coherent dma_ops callback was added to GART, however, it doesn't
return a size aligned address wrt dma_alloc_coherent, as
DMA-mapping.txt defines. This patch fixes it.
This patch also removes unused gart_map_simple
(dma_mapping_ops->map_simple has gone).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
pci-dma.c doesn't use map_simple hook any more so we can remove it
from struct dma_mapping_ops now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All the x86 DMA-API functions are defined in asm/dma-mapping.h. This patch
moves the dma_*_coherent functions also to this header file because they are
now small enough to do so.
This is done as a separate patch because it also includes some renaming and
restructuring of the dma-mapping.h file.
Signed-off-by: Joerg Roedel <joerg.roede@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All dma_ops implementations support the alloc_coherent and free_coherent
callbacks now. This allows a big simplification of the dma_alloc_coherent
function which is done with this patch. The dma_free_coherent functions is also
cleaned up and calls now the free_coherent callback of the dma_ops
implementation.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ v2 - x86: make gart_alloc_coherent return zeroed memory
FUJITA Tomonori pointed it out that the dma_alloc_coherent function
should return memory set to zero. This patch adds this to the GART
implementation too. ]
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
while fixing a different bug i moved the call to vmi_init before
early params could be parsed.
This broke the vmi specific commandline parameters.
Fix that, by moving vmi initialization after kernel has got a chance to
parse early parameters.
Signed-off-by: Alok N Kataria <akataria@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
early_io{re,un}map() are __init and hence can't be called from __meminit
functions.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While I don't have a hotplug capable system at hand, I think two issues need
fixing:
- pud_phys (in kernel_physical_ampping_init()) would remain uninitialized in
the after_bootmem case
- the locking done just around phys_pmd_{init,update}() would leave out pgd
updates, and it was needlessly covering code portions that do allocations
(perhaps using a more friendly gfp value in alloc_low_page() would then be
possible)
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Actually, might as well simply reconstruct the memtype list at free time
I guess. How is this for a coalescing version of the array functions?
Compiles, boots and provides me with:
root@7ixe4:~# wc -l /debug/x86/pat_memtype_list
53 /debug/x86/pat_memtype_list
otherwise (down from 16384+).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The new set_memory_array_{uc,wb}() pass virtual addresses to
{reserve,free}_memtype() it seems.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Joshua Hoblitt reported that only 3 GB of his 16 GB of RAM is
usable. Booting with mtrr_show showed us the BIOS-initialized
MTRR settings - which are all wrong.
So the root cause is that the BIOS has not set the mask correctly:
> [ 0.429971] MSR00000200: 00000000d0000000
> [ 0.433305] MSR00000201: 0000000ff0000800
> should be ==> [ 0.433305] MSR00000201: 0000003ff0000800
>
> [ 0.436638] MSR00000202: 00000000e0000000
> [ 0.439971] MSR00000203: 0000000fe0000800
> should be ==> [ 0.439971] MSR00000203: 0000003fe0000800
>
> [ 0.443304] MSR00000204: 0000000000000006
> [ 0.446637] MSR00000205: 0000000c00000800
> should be ==> [ 0.446637] MSR00000205: 0000003c00000800
>
> [ 0.449970] MSR00000206: 0000000400000006
> [ 0.453303] MSR00000207: 0000000fe0000800
> should be ==> [ 0.453303] MSR00000207: 0000003fe0000800
>
> [ 0.456636] MSR00000208: 0000000420000006
> [ 0.459970] MSR00000209: 0000000ff0000800
> should be ==> [ 0.459970] MSR00000209: 0000003ff0000800
So detect this borkage and add the prefix 111.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch changes the pfn args from 'u32' to 'unsigned long'
on alloc_p*() functions on paravirt_ops, and the corresponding
implementations for Xen and VMI. The prototypes for CONFIG_PARAVIRT=n
are already using unsigned long, so paravirt.h now matches the prototypes
on asm-x86/pgalloc.h.
It shouldn't result in any changes on generated code on 32-bit, with
or without CONFIG_PARAVIRT. On both cases, 'codiff -f' didn't show any
change after applying this patch.
On 64-bit, there are (expected) binary changes only when CONFIG_PARAVIRT
is enabled, as the patch is really supposed to change the size of the
pfn args.
[ v2: KVM_GUEST: use the right parameter type on kvm_release_pt() ]
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Acked-by: Jeremy Fitzhardinge <jeremy@goop.org>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We changed the interface of some pageattr, this patch makes
pageattr-test compile.
Signed-off-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add array interface APIs of pageattr. page based cache flush is quite
slow for a lot of pages. If pages are more than 1024 (4M), the patch
will use a wbinvd(). We have a simple test here (run a 3d game - open
arena), nearly all agp memory allocation are small (< 1M), so suppose
this will not impact runtime performance.
Signed-off-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Pentium III and Core Solo/Duo CPUs have an erratum
" Page with PAT set to WC while associated MTRR is UC may consolidate to UC "
which can result in WC setting in PAT to be ineffective. We will disable
PAT on such CPUs, so that we can continue to use MTRR WC setting.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All kernel mappings like ioremap(), etc uses UC_MINUS as the type. /dev/mem
mappings with /dev/mem being opened with O_SYNC however was using UC,
resulting in a conflict with /dev/mem mmap failing. This seems to be
affecting some apps (one being flashrom) which are using O_SYNC and which were
working before.
Switch /dev/mem with O_SYNC also to UC_MINUS.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Big thinko in pat memtype tracking code. reserve_memtype should be called
with physical address and not virtual address.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for the E820_UNUSABLE memory type, which is defined in
Revision 3.0b (Oct. 10, 2006) of the ACPI Specification on p. 394 Table
14-1:
AddressRangeUnusuable This range of address contains memory in which
errors have been detected. This range must not be used by the OSPM.
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: Gang Wei <gang.wei@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This section mismatch:
>> Seems to be a section mismatch; init_intel() is __cpuinit while
>> numaq_tsc_disable() is __init. Seems to be introduced in:
>>
>> commit 64898a8bad
>> Author: Yinghai Lu <yhlu.kernel@gmail.com>
>> Date: Sat Jul 19 18:01:16 2008 -0700
>>
>> x86: extend and use x86_quirks to clean up NUMAQ code
>
> Oops, I am wrong about numaq_tsc_disable() being __init. Still, I
> believe that Yinghai might be able to say what's really wrong :-)
Would lead to this crash:
BUG: unable to handle kernel paging request at c08a45f0
IP: [<c08a45f0>] numaq_tsc_disable+0x0/0x40
Fixed by the patch below.
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
None of the spinlock API is exported GPL, so there's no reason for
pv_lock_ops to be.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: drago01 <drago01@gmail.com>
WARNING: vmlinux.o(.text+0x180af): Section mismatch in reference from the function leave_uniprocessor() to the function .cpuinit.text:cpu_up()
The function leave_uniprocessor() references
the function __cpuinit cpu_up().
This is often because leave_uniprocessor lacks a __cpuinit
annotation or the annotation of cpu_up is wrong.
leave_uniprocessor calls cpu_up only when CONFIG_HOTPLUG_CPU is set,
so it can be safely annotated as __ref
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pekka Paalanen <pq@iki.fi>
after following patch,
commit 1b313f4a6d
Author: Cyrill Gorcunov <gorcunov@gmail.com>
Date: Mon Aug 18 20:45:57 2008 +0400
x86: apic - generic_processor_info
- use physid_set instead of phys_cpu and physids_or
- set phys_cpu_present_map bit AFTER check for allowed
number of processors
- add checking for APIC valid version in 64bit mode
(mostly not needed but added for merging purpose)
- add apic_version definition for 64bit mode which
is used now
we are getting warning for acpi path on 64 bit system.
make the 64-bit side fill in apic_version[] as well.
[ mingo@elte.hu: build fix ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
