Actually clfe and surround DACs are inverted in alc883_dac_nids array
(see ALC883 datasheet). I discovered this while testing multi-channel
setup (using 3stack-6ch-dig model) on MSI 945GCM5 V2 motherboard that
has an ALC883 codec. Simply Rear Left/Right and Center/LFE were swapped
in 6 channel mode (also in 4 channel mode you didn't get rear left/right
output). Other models also were affected by this bug, as can be seen by
the mixer layouts that "workaround" this (the real bug was not noticed,
and some other models simply played with mixer and initial verbs). Thus
along with fixing the order of dac nids, also change the models that
relied on previous dac ordering properly.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The docking station headphone output had no audio and jack sense
was not considered.
Jack information from the laptop itself and the dock are combined, as
the dock does not obscure the connector.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Map 3stack-6ch-dig ALC662 model for Asus P5GC-MX.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently ALC662 doesn't suport amp mute for AmpOut in nids 0x02, 0x03,
0x04 (see block diagram in ALC662 datasheet page 3, does M correspond to
mute?). The result is that currently mute for "Front Playback Switch",
"Surround Playback Switch", "Center Playback Switch" and "LFE Playback
Switch" mixer items doesn't work (tested on Asus P5GC-MX motherboard
with 3stack-6ch model).
The solution I found for this is to mute the proper inputs in 0x0c,
0x0d, 0x0e audio mixers.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Improved ALC262 ultra model for Samsung Q1 Ultra series.
- clean up mixers
- support of input from HP jack as a mic
- add quirk for Q1 EL
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The default capture source should be the mic which is 0x01 on this model.
In addition to that the change to VREF50 allows for higher capture volume.
Signed-off-by: Michael Gruber <lists.mg@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for the Toshiba Equium L30 laptop and renames the mixer
controls to match Laptop usages.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the internal mic as a capture source item for ALC268 acer model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for Pi2515.
This model is to support it. ALSA bug#3800.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NEC S970 has no sound in the internal speakers when autodetection is
used.
With targa-dig model, there is sound in the speakers and it gets
correctly muted when pluging headphones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no suitable model for M720R (ALSA bug#3781).
This patch is to support HP jack-sensing and mixer.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the array declaration to hda_codec.c where it is used and add includes
where the individual presets are declared.
Fixes the following sparse warnings:
sound/pci/hda/patch_realtek.c:13744:25: warning: symbol 'snd_hda_preset_realtek' was not declared. Should it be static?
sound/pci/hda/patch_cmedia.c:729:25: warning: symbol 'snd_hda_preset_cmedia' was not declared. Should it be static?
sound/pci/hda/patch_analog.c:3656:25: warning: symbol 'snd_hda_preset_analog' was not declared. Should it be static?
sound/pci/hda/patch_sigmatel.c:3995:25: warning: symbol 'snd_hda_preset_sigmatel' was not declared. Should it be static?
sound/pci/hda/patch_si3054.c:286:25: warning: symbol 'snd_hda_preset_si3054' was not declared. Should it be static?
sound/pci/hda/patch_atihdmi.c:156:25: warning: symbol 'snd_hda_preset_atihdmi' was not declared. Should it be static?
sound/pci/hda/patch_conexant.c:1721:25: warning: symbol 'snd_hda_preset_conexant' was not declared. Should it be static?
sound/pci/hda/patch_via.c:1962:25: warning: symbol 'snd_hda_preset_via' was not declared. Should it be static?
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialize the capture source properly for auto model.
It's especially important for cases that only mic is detected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the beep volume control to ALC268 codec support code.
Since the codec doesn't return the correct AMP caps, we need to override
the value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a private array for TLV entries of virtual master controls instead
of (supposed) static array. This cleans up the existing codes.
Also, now vmaster assumes the simple dB-range TLV that is the only type
it can handle.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC262 must have capsrc_nids defined as well as in ALC882.
Also, add a NULL check in alc882_mux_enum_put to avoid Oops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The last patch for fixing the auto-config pin setting breaks the resume
due to a wrong use of snd_hda_codec_amp_stereo(). The code in the init
hook shouldn't touch the amp cache.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new mixer switch to enable/disable the sharing of the default
PCM stream with analog and SPDIF outputs. When "IEC958 Default PCM"
switch is on, the PCM stream is routed both to analog and SPDIF outputs.
This is the behavior in the earlier version.
Turning this switch off has a merit for some codecs, though. Some codec
chips don't support 24bit formats for SPDIF but only for analog outputs.
In this case, you can use 24bit format by disabling this switch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes some bugs in the auto-configurator of Realtek codecs:
- add missing pin set-up for speaker pins
- fix the speaker auto-mute function not to conflict with the existing
"Speaker" mixer switch
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clean up the codes of the capture source selection for Realtek codecs.
Now using common helper functions with the new capsrc_nids field.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I've just noticed that there are a handful of duplicate controls in the
ALC268 test model mixer. This patch (against alsa-driver 1.0.16) removes
them.
Signed-off-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current scheme, PCM device numbers are assigned incrementally
in the order of codecs. This causes problems when the codec number
is irregular, e.g. codec #0 for HDMI and codec #1 for analog. Then
the HDMI becomes the first PCM, which is picked up as the default
output device. Unfortuantely this doesn't work well with normal
setups.
This patch introduced the fixed device numbers for the PCM types,
namely, analog, SPDIF, HDMI and modem. The PCM devices are assigned
according to the corresponding PCM type. After this patch, HDMI will
be always assigned to PCM #3, SPDIF to PCM #1, and the first analog
to PCM #0, etc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the line-out volume control of eeepc p701 to be a proper slave of
the virtual master control.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models like eeepc ep20 have invalid mixer names that aren't
handled properly by virtual master controls. Rename them to the
proper names.
Also fixed some typos in the mixer names but they are not compiled
in right now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds a quirk to the Realtek ALC883 table for the Albatron KI690-AM2
motherboard to use the 6stack-dig model.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The capture source selection for ADC list with two elements is buggy
becaues of a wrong capture mux list. This patch fixes the starting
index based on spec->num_adc_nids.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The widget list of capture source selection for ALC883 contains the
wrong NIDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add SPDIF playback switch to the slave element list so that it
can be toggled via the master control as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the speaker-automute function to ALC262 HP models.
Also, 'Mono' mixer elements are renamed as more intuitive 'Speaker'.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Removed the PCM mixer elements conflicting with others.
Also renamed Master control to Headphone, which isn't a real master.
(The Master control is still created as a virtual master even after
this rename.)
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The PCM mixer elements in HP T5735 model of ALC262 codec conflict
with Speaker and Headphone volumes. They should be removed.
Ditto for LineOut that is identical with Speaker.
Also, fixed/cleaned up the auto-mute callback to use the amp cache
correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Renamed the non-standard mixer elements 'iSpeaker' to 'Speaker'
in Realtek codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simplify usage of the Acer Aspire 5310 laptop with the ALC268 based codec
sound card via add correct PCI SSID.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Simplify usage of the Acer Aspire 5315 laptop with the ALC268 based codec
sound card via add correct PCI SSID.
Signed-off-by: Andy Shevchenko <andy@smile.org.ua>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fixed the bug that multiple capture streams conflict on Realtek codec
routines.
Also, this adds a framework to enable the alternative playback stream,
e.g. for VoIP. It's not fully implemented yet, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support of Dell OEM laptops (Vostro 1200) with ALC268 codec.
The new model=dell is provided.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It turned out that the PCBEEP element (0x1d) is disabled on some hardwares
although it's defined in the datasheet. Because of the error at info of
this element, the mixer gets totally unusable.
Since the PCBEEP isn't that important feature, it's safer to disable this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch fixes 5.1 surround output and headphone detection in the
Dell Inspiron 530 and possibly other Dell systems using the ALC888
codec (mode 6stack-dell).
Signed-off-by: Claudio Matsuoka <cmatsuoka@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The ALC auto-probe creates mic boost controls automatically for the
probed pins, but it assumes that they are analog mics. The digital
mics have no boost controls and must be skipped.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add master controls using vmaster to codecs that have no real hardware
master volume registers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Herton Ronaldo Krzesinski