This adds various fields in the PACA that are for use specifically
by Book3E processors, such as exception save areas, current pgd
pointer, special exceptions kernel stacks etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds various definitions and macros used by the exception and TLB
miss handling on 64-bit BookE
It also adds the definitions of the SPRGs used for various exception types
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the PTE and pgtable format definitions, along with changes
to the kernel memory map and other definitions related to implementing
support for 64-bit Book3E. This also shields some asm-offset bits that
are currently only relevant on 32-bit
We also move the definition of the "linux" page size constants to
the common mmu.h file and add a few sizes that are relevant to
embedded processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds various SPRs defined on 64-bit BookE, along with changes
to the definition of the base MSR values to add the values needed
for 64-bit Book3E.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
That patch used to just add a hook to page table flushing but
pulling that string brought out a whole bunch of issues, so it
now does that and more:
- We now make the RCU batching of page freeing SMP only, as I
believe it was intended initially. We make a few more things compile
to nothing on !CONFIG_SMP
- Some macros are turned into functions, though that forced me to
out of line a few stuffs due to unsolvable include depenencies,
however it's probably better that way anyway, it's not -that-
critical code path.
- 32-bit didn't call pte_free_finish() on tlb_flush() which means
that it wouldn't push out the batch to RCU for delayed freeing when
a bunch of page tables have been freed, they would just stay in there
until the batch gets full.
64-bit BookE will use that hook to maintain the virtually linear
page tables or the indirect entries in the TLB when using the
HW loader.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Those definitions are currently declared extern in the .c file where
they are used, move them to a header file instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, a single ifdef covers SLB related bits and more generic ppc64
related bits, split this in two separate ifdef's since 64-bit BookE will
need one but not the other.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Our 64-bit hash context handling has no init function, but 64-bit Book3E
will use the common mmu_context_nohash.c code which does, so define an
empty inline mmu_context_init() for 64-bit server and call it from
our 64-bit setup_arch()
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
We need to pass down whether the page is direct or indirect and we'll
need to pass the page size to _tlbil_va and _tlbivax_bcast
We also add a new low level _tlbil_pid_noind() which does a TLB flush
by PID but avoids flushing indirect entries if possible
This implements those new prototypes but defines them with inlines
or macros so that no additional arguments are actually passed on current
processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The way I intend to use tophys/tovirt on 64-bit BookE is different
from the "trick" that we currently play for 32-bit BookE so change
the condition of definition of these macros to make it so.
Also, make sure we only use rfid and mtmsrd instead of rfi and mtmsr
for 64-bit server processors, not all 64-bit processors.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This adds some code to do early ioremap's using page tables instead of
bolting entries in the hash table. This will be used by the upcoming
64-bits BookE port.
The patch also changes the test for early vs. late ioremap to use
slab_is_available() instead of our old hackish mem_init_done.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds various additional bit definitions for various MMU related
SPRs used on Book3E.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This adds the opcode definitions to ppc-opcode.h for the two instructions
tlbivax and tlbsrx. as defined by Book3E 2.06
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current "no hash" MMU context management code is written with
the assumption that one CPU == one TLB. This is not the case on
implementations that support HW multithreading, where several
linux CPUs can share the same TLB.
This adds some basic support for this to our context management
and our TLB flushing code.
It also cleans up the optional debugging output a bit
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
enter_prom() used to save and restore registers such as CTR, XER etc..
which are volatile, or SRR0,1... which we don't care about. This
removes a bunch of useless code and while at it turns an mtmsrd into
an MTMSRD macro which will be useful to Book3E.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
A misplaced #endif causes more definitions than intended to be
protected by #ifndef __ASSEMBLY__. This breaks upcoming 64-bit
BookE support patch when using 64k pages.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The truncate syscall has a signed long parameter, so when using a 32-
bit userspace with a 64-bit kernel the argument is zero-extended
instead of sign-extended. Adding the compat_sys_truncate function
fixes the issue.
This was noticed during an LSB truncate test failure. The test was
checking for the correct error number set when truncate is called with
a length of -1. The test can be found at:
http://bzr.linuxfoundation.org/lsb/devel/runtime-test?cmd=inventory;rev=stewb%40linux-foundation.org-20090626205411-sfb23cc0tjj7jzgm;path=modules/vsx-pcts/tset/POSIX.os/files/truncate/
BenH: Added compat_sys_ftruncate() as well, same issue.
Signed-off-by: Chase Douglas <cndougla@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dtc was moved in 9fffb55f66 from
arch/powerpc/boot/ to scripts/dtc/
This patch updates the wrapper script to point to the new location of dtc.
Signed-off-by: Lucian Adrian Grijincu <lgrijincu@ixiacom.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Frans Pop <elendil@planet.nl>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This change the SPRG used to store the PACA on ppc64 from
SPRG3 to SPRG1. SPRG3 is user readable on most processors
and we want to use it for other things. We change the scratch
SPRG used by exception vectors from SRPG1 to SPRG2.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The code for setting up the IPIs for SMP PowerSurge marchines bitrot,
it needs to properly map the HW interrupt number
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current definitions set ranges and defaults for 32 and 64-bit
only using "PPC_STD_MMU" which means hash based MMU. This uselessly
restrict the usefulness for the upcoming 64-bit BookE port, but more
than that, it's broken on 32-bit since the only 32-bit platform
supporting multiple page sizes currently is 44x which does -not-
have PPC_STD_MMU_32 set.
This fixes it by using PPC64 and PPC32 instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Replace strncpy() and explicit null-termination by strlcpy()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The STAB code used on Power3 and RS/64 uses a second scratch SPRG to
save a GPR in order to decide whether to go to do_stab_bolted_* or
to handle a normal data access exception.
This prevents our scheme of freeing SPRG3 which is user visible for
user uses since we cannot use SPRG0 which, on RS/64, seems to be
read-only for supervisor mode (like POWER4).
This reworks the STAB exception entry to use the PACA as temporary
storage instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The kernel uses SPRG registers for various purposes, typically in
low level assembly code as scratch registers or to hold per-cpu
global infos such as the PACA or the current thread_info pointer.
We want to be able to easily shuffle the usage of those registers
as some implementations have specific constraints realted to some
of them, for example, some have userspace readable aliases, etc..
and the current choice isn't always the best.
This patch should not change any code generation, and replaces the
usage of SPRN_SPRGn everywhere in the kernel with a named replacement
and adds documentation next to the definition of the names as to
what those are used for on each processor family.
The only parts that still use the original numbers are bits of KVM
or suspend/resume code that just blindly needs to save/restore all
the SPRGs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The file include/asm/exception.h contains definitions
that are specific to exception handling on 64-bit server
type processors.
This renames the file to exception-64s.h to reflect that
fact and avoid confusion.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
TASK_UNMAPPED_BASE is not used with the new top down mmap layout. We can
reuse this preload slot by loading in the segment at 0x10000000, where almost
all PowerPC binaries are linked at.
On a microbenchmark that bounces a token between two 64bit processes over pipes
and calls gettimeofday each iteration (to access the VDSO), both the 32bit and
64bit context switch rate improves (tested on a 4GHz POWER6):
32bit: 273k/sec -> 283k/sec
64bit: 277k/sec -> 284k/sec
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With the new top down layout it is likely that the pc and stack will be in the
same segment, because the pc is most likely in a library allocated via a top
down mmap. Right now we bail out early if these segments match.
Rearrange the SLB preload code to sanity check all SLB preload addresses
are not in the kernel, then check all addresses for conflicts.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On 64bit applications the VDSO is the only thing in segment 0. Since the VDSO
is position independent we can remove the hint and let get_unmapped_area pick
an area. This will mean the vdso will be near other mmaps and will share
an SLB entry:
10000000-10001000 r-xp 00000000 08:06 5778459 /root/context_switch_64
10010000-10011000 r--p 00000000 08:06 5778459 /root/context_switch_64
10011000-10012000 rw-p 00001000 08:06 5778459 /root/context_switch_64
fffa92ae000-fffa92b0000 rw-p 00000000 00:00 0
fffa92b0000-fffa9453000 r-xp 00000000 08:06 4334051 /lib64/power6/libc-2.9.so
fffa9453000-fffa9462000 ---p 001a3000 08:06 4334051 /lib64/power6/libc-2.9.so
fffa9462000-fffa9466000 r--p 001a2000 08:06 4334051 /lib64/power6/libc-2.9.so
fffa9466000-fffa947c000 rw-p 001a6000 08:06 4334051 /lib64/power6/libc-2.9.so
fffa947c000-fffa9480000 rw-p 00000000 00:00 0
fffa9480000-fffa94a8000 r-xp 00000000 08:06 4333852 /lib64/ld-2.9.so
fffa94b3000-fffa94b4000 rw-p 00000000 00:00 0
fffa94b4000-fffa94b7000 r-xp 00000000 00:00 0 [vdso] <----- here I am
fffa94b7000-fffa94b8000 r--p 00027000 08:06 4333852 /lib64/ld-2.9.so
fffa94b8000-fffa94bb000 rw-p 00028000 08:06 4333852 /lib64/ld-2.9.so
fffa94bb000-fffa94bc000 rw-p 00000000 00:00 0
fffe4c10000-fffe4c25000 rw-p 00000000 00:00 0 [stack]
On a microbenchmark that bounces a token between two 64bit processes over pipes
and calls gettimeofday each iteration (to access the VDSO), our context switch
rate goes from 268k to 277k ctx switches/sec (tested on a 4GHz POWER6).
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The bitops.h functions that operate on a single bit in a bitfield are
implemented by operating on the corresponding word location. In all
cases the inner logic is valid if the mask being applied has more than
one bit set, so this patch exposes those inner operations. Indeed,
set_bits() was already available, but it duplicated code from
set_bit() (rather than making the latter a wrapper) - it was also
missing the PPC405_ERR77() workaround and the "volatile" address
qualifier present in other APIs. This corrects that, and exposes the
other multi-bit equivalents.
One advantage of these multi-bit forms is that they allow word-sized
variables to essentially be their own spinlocks, eg. very useful for
state machines where an atomic "flags" variable can obviate the need
for any additional locking.
Signed-off-by: Geoff Thorpe <geoff@geoffthorpe.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The workaround enabled by CONFIG_MPIC_BROKEN_REGREAD does not work
on non-broken MPICs. The symptom is no interrupts being received.
The fix is twofold. Firstly the code was broken for multiple isus,
we need to index into the shadow array with the src_no, not the idx.
Secondly, we always do the read, but only use the VECPRI_MASK and
VECPRI_ACTIVITY bits from the hardware, the rest of "val" comes
from the shadow.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This allows to remove the ppc_md.init() hook in the setup code.
Signed-off-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make sure the stack-protector segment registers are properly set up
before calling any functions which may have stack-protection compiled
into them.
[ Impact: prevent Xen early-boot crash when stack-protector is enabled ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
load_percpu_segment() is used to set up the per-cpu segment registers,
which are also used for -fstack-protector. Make sure that the
load_percpu_segment() function doesn't have stackprotector enabled.
[ Impact: allow percpu setup before calling stack-protected functions ]
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* 'next' of git://git.monstr.eu/linux-2.6-microblaze:
microblaze: Update Microblaze defconfigs
microblaze: Use klimit instead of _end for memory init
microblaze: Enable ppoll syscall
microblaze: Sane handling of missing timer/intc in device tree
microblaze: use the generic ack_bad_irq implementation
Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.
This results in a deadlock in this scenario.
cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.
This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.
Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.
Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.
This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Normally, srmmu uses different trap table register values to allow
determination of the cpu we're on. All of the trap tables have
identical content, they just sit at different offsets from the first
trap table, and the offset shifted down and masked out determines
the cpu we are on.
The code tries to free them up when they aren't actually used
(don't have all 4 cpus, we're on sun4d, etc.) but that causes
problems.
For one thing it triggers false positives in the DMA debugging
code. And fixing that up while preserving this relative offset
thing isn't trivial.
So just kill the freeing code, it costs us at most 3 pages, big
deal...
Signed-off-by: David S. Miller <davem@davemloft.net>
I think arch/sparc/kernel/sys32.S has an incorrect splice definition:
SIGN2(sys32_splice, sys_splice, %o0, %o1)
The splice() prototype looks like :
long splice(int fd_in, loff_t *off_in, int fd_out,
loff_t *off_out, size_t len, unsigned int flags);
So I think we should have :
SIGN2(sys32_splice, sys_splice, %o0, %o2)
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: use the right flag for get_vm_area()
percpu, sparc64: fix sparse possible cpu map handling
init: set nr_cpu_ids before setup_per_cpu_areas()
Commit 0e83815be7 changed the
section the initial_code variable gets allocated in, in an
attempt to address a section conflict warning. This, however
created a new section conflict when building without
HOTPLUG_CPU. The apparently only (reasonable) way to address
this is to always use __REFDATA.
Once at it, also fix a second section mismatch when not using
HOTPLUG_CPU.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <4A8AE7CD020000780001054B@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For noMMU system when you use larger rootfs image
there is problem with using _end label because
we increase klimit but in memory initialization
we use still _end which is wrong. Larger mtd rootfs
was rewritten by init_bootmem_node.
MMU kernel use static initialization where klimit
is setup to _end. There is no any other hanling
with klimit.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This code path doesn't test any returned pointers for NULL, leading to a bad
kernel page fault if there's no timer/intc found.
Slightly better is to BUG(), but even better still would be a printk beforehand.
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This adds support for tracing callchains for powerpc, both 32-bit
and 64-bit, and both in the kernel and userspace, from PMU interrupt
context.
The first three entries stored for each callchain are the NIP (next
instruction pointer), LR (link register), and the contents of the LR
save area in the second stack frame (the first is ignored because the
ABI convention on powerpc is that functions save their return address
in their caller's stack frame). Because leaf functions don't have to
save their return address (LR value) and don't have to establish a
stack frame, it's possible for either or both of LR and the second
stack frame's LR save area to have valid return addresses in them.
This is basically impossible to disambiguate without either reading
the code or looking at auxiliary information such as CFI tables.
Since we don't want to do either of those things at interrupt time,
we store both LR and the second stack frame's LR save area.
Once we get past the second stack frame, there is no ambiguity; all
return addresses we get are reliable.
For kernel traces, we check whether they are valid kernel instruction
addresses and store zero instead if they are not (rather than
omitting them, which would make it impossible for userspace to know
which was which). We also store zero instead of the second stack
frame's LR save area value if it is the same as LR.
For kernel traces, we check for interrupt frames, and for user traces,
we check for signal frames. In each case, since we're starting a new
trace, we store a PERF_CONTEXT_KERNEL/USER marker so that userspace
knows that the next three entries are NIP, LR and the second stack frame
for the interrupted context.
We read user memory with __get_user_inatomic. On 64-bit, if this
PMU interrupt occurred while interrupts are soft-disabled, and
there is no MMU hash table entry for the page, we will get an
-EFAULT return from __get_user_inatomic even if there is a valid
Linux PTE for the page, since hash_page isn't reentrant. Thus we
have code here to read the Linux PTE and access the page via the
kernel linear mapping. Since 64-bit doesn't use (or need) highmem
there is no need to do kmap_atomic. On 32-bit, we don't do soft
interrupt disabling, so this complication doesn't occur and there
is no need to fall back to reading the Linux PTE, since hash_page
(or the TLB miss handler) will get called automatically if necessary.
Note that we cannot get PMU interrupts in the interval during
context switch between switch_mm (which switches the user address
space) and switch_to (which actually changes current to the new
process). On 64-bit this is because interrupts are hard-disabled
in switch_mm and stay hard-disabled until they are soft-enabled
later, after switch_to has returned. So there is no possibility
of trying to do a user stack trace when the user address space is
not current's address space.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This provides a mechanism to allow the perf_counters code to access
user memory in a PMU interrupt routine. Such an access can cause
various kinds of interrupt: SLB miss, MMU hash table miss, segment
table miss, or TLB miss, depending on the processor. This commit
only deals with 64-bit classic/server processors, which use an MMU
hash table. 32-bit processors are already able to access user memory
at interrupt time. Since we don't soft-disable on 32-bit, we avoid
the possibility of reentering hash_page or the TLB miss handlers,
since they run with interrupts disabled.
On 64-bit processors, an SLB miss interrupt on a user address will
update the slb_cache and slb_cache_ptr fields in the paca. This is
OK except in the case where a PMU interrupt occurs in switch_slb,
which also accesses those fields. To prevent this, we hard-disable
interrupts in switch_slb. Interrupts are already soft-disabled at
this point, and will get hard-enabled when they get soft-enabled
later.
This also reworks slb_flush_and_rebolt: to avoid hard-disabling twice,
and to make sure that it clears the slb_cache_ptr when called from
other callers than switch_slb, the existing routine is renamed to
__slb_flush_and_rebolt, which is called by switch_slb and the new
version of slb_flush_and_rebolt.
Similarly, switch_stab (used on POWER3 and RS64 processors) gets a
hard_irq_disable() to protect the per-cpu variables used there and
in ste_allocate.
If a MMU hashtable miss interrupt occurs, normally we would call
hash_page to look up the Linux PTE for the address and create a HPTE.
However, hash_page is fairly complex and takes some locks, so to
avoid the possibility of deadlock, we check the preemption count
to see if we are in a (pseudo-)NMI handler, and if so, we don't call
hash_page but instead treat it like a bad access that will get
reported up through the exception table mechanism. An interrupt
whose handler runs even though the interrupt occurred when
soft-disabled (such as the PMU interrupt) is considered a pseudo-NMI
handler, which should use nmi_enter()/nmi_exit() rather than
irq_enter()/irq_exit().
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On 32-bit systems with 64-bit PTEs, the PTEs have to be written in two
32-bit halves. On SMP we write the higher-order half and then the
lower-order half, with a write barrier between the two halves, but on
UP there was no particular ordering of the writes to the two halves.
This extends the ordering that we already do on SMP to the UP case as
well. The reason is that with the perf_counter subsystem potentially
accessing user memory at interrupt time to get stack traces, we have
to be careful not to create an incorrect but apparently valid PTE even
on UP.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Max Vozeler reported:
> Bug 13877 - bogl-term broken with CONFIG_X86_PAT=y, works with =n
>
> strace of bogl-term:
> 814 mmap2(NULL, 65536, PROT_READ|PROT_WRITE, MAP_SHARED, 4, 0)
> = -1 EAGAIN (Resource temporarily unavailable)
> 814 write(2, "bogl: mmaping /dev/fb0: Resource temporarily unavailable\n",
> 57) = 57
PAT code maps the ISA memory range as WB in the PAT attribute, so that
fixed range MTRR registers define the actual memory type (UC/WC/WT etc).
But the upper level is_new_memtype_allowed() API checks are failing,
as the request here is for UC and the return tracked type is WB (Tracked type is
WB as MTRR type for this legacy range potentially will be different for each
4k page).
Fix is_new_memtype_allowed() by always succeeding the ISA address range
checks, as the null PAT (WB) and def MTRR fixed range register settings
satisfy the memory type needs of the applications that map the ISA address
range.
Reported-and-Tested-by: Max Vozeler <xam@debian.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch fixes warnings like this:
CC fs/proc/meminfo.o
In file included from /work/linux/include/linux/mmzone.h:20,
from /work/linux/include/linux/gfp.h:4,
from /work/linux/include/linux/mm.h:8,
from /work/linux/fs/proc/meminfo.c:5:
/work/linux/arch/mips/include/asm/page.h:36:1: warning: "HPAGE_SIZE" redefined
In file included from /work/linux/fs/proc/meminfo.c:2:
/work/linux/include/linux/hugetlb.h:107:1: warning: this is the location of the previous definition
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
An older test-box started hanging at the following point during
bootup:
[ 0.022996] Mount-cache hash table entries: 512
[ 0.024996] Initializing cgroup subsys debug
[ 0.025996] Initializing cgroup subsys cpuacct
[ 0.026995] Initializing cgroup subsys devices
[ 0.027995] Initializing cgroup subsys freezer
[ 0.028995] mce: CPU supports 5 MCE banks
I've bisected it down to commit 4efc0670 ("x86, mce: use 64bit
machine check code on 32bit"), which utilizes the MCE code on
32-bit systems too.
The problem is caused by this detail in my config:
# CONFIG_CPU_SUP_INTEL is not set
This disables the quirks in mce_cpu_quirks() but still enables
MCE support - which then hangs due to the missing quirk
workaround needed on this CPU:
if (c->x86 == 6 && c->x86_model < 0x1A && banks > 0)
mce_banks[0].init = 0;
The safe solution is to not initialize MCEs if we dont know on
what CPU we are running (or if that CPU's support code got
disabled in the config).
Also be a bit more defensive on 32-bit systems: dont do a
boot-time dump of pending MCEs not just on the specific system
that we found a problem with (Pentium-M), but earlier ones as
well.
Now this problem is probably not common and disabling CPU
support is rare - but still being more defensive in something
we turned on for a wide range of CPUs is prudent.
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
LKML-Reference: Message-ID: <4A88E3E4.40506@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On my legacy Pentium M laptop (Acer Extensa 2900) I get bogus MCE on a cold
boot with CONFIG_X86_NEW_MCE enabled, i.e. (after decoding it with mcelog):
MCE 0
HARDWARE ERROR. This is *NOT* a software problem!
Please contact your hardware vendor
CPU 0 BANK 1 MCG status:
MCi status:
Error overflow
Uncorrected error
Error enabled
Processor context corrupt
MCA: Data CACHE Level-1 UNKNOWN Error
STATUS f200000000000195 MCGSTATUS 0
[ The other STATUS values observed: f2000000000001b5 (... UNKNOWN error)
and f200000000000115 (... READ Error).
To verify that this is not a CONFIG_X86_NEW_MCE bug I also modified
the CONFIG_X86_OLD_MCE code (which doesn't log any MCEs) to dump
content of STATUS MSR before it is cleared during initialization. ]
Since the bogus MCE results in a kernel taint (which in turn disables
lockdep support) don't log boot MCEs on Pentium M (model == 13) CPUs
by default ("mce=bootlog" boot parameter can be be used to get the old
behavior).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The function uv_acpi_madt_oem_check() has been marked __init,
the struct apic_x2apic_uv_x has been marked __refdata.
The aim is to address the following section mismatch messages:
WARNING: arch/x86/kernel/apic/built-in.o(.data+0x1368): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/kernel/built-in.o(.data+0x68e8): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: arch/x86/built-in.o(.text+0x7b36f): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_ioremap()
The function uv_acpi_madt_oem_check() references
the function __init early_ioremap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_ioremap is wrong.
WARNING: arch/x86/built-in.o(.text+0x7b38d): Section mismatch in reference from the function uv_acpi_madt_oem_check() to the function .init.text:early_iounmap()
The function uv_acpi_madt_oem_check() references
the function __init early_iounmap().
This is often because uv_acpi_madt_oem_check lacks a __init
annotation or the annotation of early_iounmap is wrong.
WARNING: arch/x86/built-in.o(.data+0x8668): Section mismatch in reference from the variable apic_x2apic_uv_x to the function .cpuinit.text:uv_wakeup_secondary()
The variable apic_x2apic_uv_x references
the function __cpuinit uv_wakeup_secondary()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
LKML-Reference: <200908161855.48302.lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The u300_init_check_chip() function was not properly tagged with
the __init macro and provided a initsection mismatch on
compilation.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently, highmem is selectable, and you can request an increased
vmalloc area. However, none of this has any effect on the memory
layout since a patch in the highmem series was accidentally dropped.
Moreover, even if you did want highmem, all memory would still be
registered as lowmem, possibly resulting in overflow of the available
virtual mapping space.
The highmem boundary is determined by the highest allowed beginning
of the vmalloc area, which depends on its configurable minimum size
(see commit 60296c71f6 for details on
this).
We should create mappings and initialize bootmem only for low memory,
while the zone allocator must still be told about highmem.
Currently, memory nodes which are completely located in high memory
are not supported. This is not a huge limitation since systems
relying on highmem support are unlikely to have discontiguous memory
with large holes.
[ A similar patch was meant to be merged before commit 5f0fbf9eca
and be available in Linux v2.6.30, however some git rebase screw-up
of mine dropped the first commit of the series, and that goofage
escaped testing somehow as well. -- Nico ]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
The SGI UV Broadcast Assist Unit is used to send TLB shootdown
messages to remote nodes of the system. The header of the
message must contain the subnode id of the block in the
receiving hub that handles such messages. It should always be
0x10, the id of the "LB" block.
It had previously been documented as a "must be zero" field.
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Acked-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <E1Mc1x7-0005Ce-6t@eag09.americas.sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch updates the SuperH Mobile sleep assembly code with
support for DBSC memory controller found in the sh7724 processor.
Without this fix the memory hooked up to the sh7724 processor
will never enter self-refresh mode before suspending to ram. The
effect of this is that the memory contents most likeley will be
lost upon resume which may or may not be what you want.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.
Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.
Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Small confusion with our hardware engineer, the WP signal (RO) is
active low on our boards, the signal has to inverted.
This is a pretty straightforward patch, it could even go to -rc,
but if not, then push it for 2.6.32.
Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
percpu code has been assuming num_possible_cpus() == nr_cpu_ids which
is incorrect if cpu_possible_map contains holes. This causes percpu
code to access beyond allocated memories and vmalloc areas. On a
sparc64 machine with cpus 0 and 2 (u60), this triggers the following
warning or fails boot.
WARNING: at /devel/tj/os/work/mm/vmalloc.c:106 vmap_page_range_noflush+0x1f0/0x240()
Modules linked in:
Call Trace:
[00000000004b17d0] vmap_page_range_noflush+0x1f0/0x240
[00000000004b1840] map_vm_area+0x20/0x60
[00000000004b1950] __vmalloc_area_node+0xd0/0x160
[0000000000593434] deflate_init+0x14/0xe0
[0000000000583b94] __crypto_alloc_tfm+0xd4/0x1e0
[00000000005844f0] crypto_alloc_base+0x50/0xa0
[000000000058b898] alg_test_comp+0x18/0x80
[000000000058dad4] alg_test+0x54/0x180
[000000000058af00] cryptomgr_test+0x40/0x60
[0000000000473098] kthread+0x58/0x80
[000000000042b590] kernel_thread+0x30/0x60
[0000000000472fd0] kthreadd+0xf0/0x160
---[ end trace 429b268a213317ba ]---
This patch fixes generic percpu functions and sparc64
setup_per_cpu_areas() so that they handle sparse cpu_possible_map
properly.
Please note that on x86, cpu_possible_map() doesn't contain holes and
thus num_possible_cpus() == nr_cpu_ids and this patch doesn't cause
any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf_counter: Report the cloning task as parent on perf_counter_fork()
perf_counter: Fix an ipi-deadlock
perf: Rework/fix the whole read vs group stuff
perf_counter: Fix swcounter context invariance
perf report: Don't show unresolved DSOs and symbols when -S/-d is used
perf tools: Add a general option to enable raw sample records
perf tools: Add a per tracepoint counter attribute to get raw sample
perf_counter: Provide hw_perf_counter_setup_online() APIs
perf list: Fix large list output by using the pager
perf_counter, x86: Fix/improve apic fallback
perf record: Add missing -C option support for specifying profile cpu
perf tools: Fix dso__new handle() to handle deleted DSOs
perf tools: Fix fallback to cplus_demangle() when bfd_demangle() is not available
perf report: Show the tid too in -D
perf record: Fix .tid and .pid fill-in when synthesizing events
perf_counter, x86: Fix generic cache events on P6-mobile CPUs
perf_counter, x86: Fix lapic printk message
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix oops in identify_cpu() on CPUs without CPUID
x86: Clear incorrectly forced X86_FEATURE_LAHF_LM flag
x86, mce: therm_throt - change when we print messages
x86: Add reboot quirk for every 5 series MacBook/Pro
Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the processor platform device setup
functions from __initcall() and sometimes
device_initcall() to arch_initcall().
This makes sure that the platform devices are
registered a bit earlier so the devices are
available when drivers register using initcall
levels earlier than device_initcall().
A good example is platform devices needed by
i2c-sh_mobile.c which registers a bit earlier
using subsys_initcall().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Johannes Stezenbach reported that his Pentium-M based
laptop does not have the local APIC enabled by default,
and hence perfcounters do not get initialized.
Add a fallback for this case: allow non-sampled counters
and return with an error on sampled counters. This allows
'perf stat' to work out of box - and allows 'perf top'
and 'perf record' to fall back on a hrtimer based sampling
method.
( Passing 'lapic' on the boot line will allow hardware
sampling to occur - but if the APIC is disabled
permanently by the hardware then this fallback still
allows more systems to use perfcounters. )
Also decouple perfcounter support from X86_LOCAL_APIC.
-v2: fix typo breaking counters on all other systems ...
Reported-by: Johannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Kernel is broken for x86 CPUs without CPUID since 2.6.28. It
crashes with NULL pointer dereference in identify_cpu():
766 generic_identify(c);
767
768--> if (this_cpu->c_identify)
769 this_cpu->c_identify(c);
this_cpu is NULL. This is because it's only initialized in
get_cpu_vendor() function, which is not called if the CPU has
no CPUID instruction.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
LKML-Reference: <200908112000.15993.linux@rainbow-software.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Between GCC version 3.4.0 and 4.3.3 (including 3.4.0 and 4.3.3), -mtune=merced
is implemented in GCC. Starting from 4.4.0, -mtune=merced is deprecated.
Even implemented in versions between 3.4.0 and 4.3.3, the -mtune=merced
feature has been broken in some of the versions. For example, GCC 4.1.2 reports
interanl tuning function errors during kernel building with -mtune=merced. Or
GCC Bugzilla 16130 reports another -mtune=merced issue on GCC 3.4.1.
So I would remove the -mtune=merced from IA64 kernel build. Without this option,
kernel on Merced will remain the same except losing an unstable and out-of-date
performance tunning feature.
Since GCC version 3.4.0, -mtune=mckinley has been implemented. The
-mtune=mckinley option functions the same as mtune=itanium2. And mtune=itanium2
is the default option. So we don't need to add mtune=mckinley either since its
been the default option in any GCC version which implements this option.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
fix the following 'make includecheck' warning:
arch/ia64/include/asm/pgtable.h: asm/processor.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
fix the following 'make includecheck' warning:
arch/ia64/kernel/ia64_ksyms.c: asm/page.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
__test_and_clear_bit() returns a bitfield with the tested-for bit set.
Make it consistent with the other bitops - of ia64 but also every
other architecture - and return a boolean value.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Fenghua Yu <fenghua.yu@intel.com>
In commit 160c1d8e40,
dma_ops->dma_supported = iommu_dma_supported;
This dma_ops->dma_supported is first called in platform_dma_init() during kernel
boot. Then dma_ops->dma_supported will be called recursively in
iommu_dma_supported.
Kernel can not boot because kernel can not get out of iommu_dma_supported until
it runs out of stack memory.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
2.6.31-rc kernels don't boot on my ixp4xx box (ds101), because the libata
driver doesn't find the PCI IDE controller any more. 2.6.30 was fine.
I traced this to a PCI update (1f82de10d6)
in 2.6.30-git19. Diffing the kernel boot logs from 2.6.30-git18 and
2.6.30-git19 illustrates the breakage:
> --- dmesg-2.6.30-git18 2009-08-04 01:45:22.000000000 +0200
> +++ dmesg-2.6.30-git19 2009-08-04 01:45:46.000000000 +0200
> @@ -26,6 +26,13 @@
> pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:02.2: PME# disabled
> PCI: bus0: Fast back to back transfers disabled
> +pci 0000:00:01.0: BAR 0: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 1: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 2: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 3: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:01.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.0: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> +pci 0000:00:02.1: BAR 4: can't allocate I/O resource [0x10000-0xffff]
> bio: create slab <bio-0> at 0
> SCSI subsystem initialized
> NET: Registered protocol family 2
> @@ -44,11 +51,7 @@
> console [ttyS0] enabled
> serial8250.0: ttyS1 at MMIO 0xc8001000 (irq = 13) is a XScale
> Driver 'sd' needs updating - please use bus_type methods
> -PCI: enabling device 0000:00:01.0 (0140 -> 0141)
> -scsi0 : pata_artop
> -scsi1 : pata_artop
> -ata1: PATA max UDMA/100 cmd 0x1050 ctl 0x1060 bmdma 0x1040 irq 28
> -ata2: PATA max UDMA/100 cmd 0x1058 ctl 0x1064 bmdma 0x1048 irq 28
> +pata_artop 0000:00:01.0: no available native port
> Using configured DiskOnChip probe address 0x50000000
> DiskOnChip found at 0x50000000
> NAND device: Manufacturer ID: 0x98, Chip ID: 0x73 (Toshiba NAND 16MiB 3,3V 8-bit)
The specific change in 1f82de10d6 responsible
for this failure turned out to be the following:
> --- a/drivers/pci/probe.c
> +++ b/drivers/pci/probe.c
> @@ -193,7 +193,7 @@ int __pci_read_base(struct pci_dev *dev, enum pci_bar_type type,
> res->flags |= pci_calc_resource_flags(l) | IORESOURCE_SIZEALIGN;
> if (type == pci_bar_io) {
> l &= PCI_BASE_ADDRESS_IO_MASK;
> - mask = PCI_BASE_ADDRESS_IO_MASK & 0xffff;
> + mask = PCI_BASE_ADDRESS_IO_MASK & IO_SPACE_LIMIT;
> } else {
> l &= PCI_BASE_ADDRESS_MEM_MASK;
> mask = (u32)PCI_BASE_ADDRESS_MEM_MASK;
Every arch except arm's ixp4xx defines IO_SPACE_LIMIT as an all-bits-one
bitmask, typically -1UL but sometimes only a 16-bit 0x0000ffff. But ixp4xx
defines it as 0xffff0000, which is now causing the PCI failures.
Russell King noted that ixp4xx has 64KB PCI IO space, so IO_SPACE_LIMIT
should be 0x0000ffff. This patch makes that change, which fixes the PCI
failures on my ixp4xx box.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Due to an erratum with certain AMD Athlon 64 processors, the
BIOS may need to force enable the LAHF_LM capability.
Unfortunately, in at least one case, the BIOS does this even
for processors that do not support the functionality.
Add a specific check that will clear the feature bit for
processors known not to support the LAHF/SAHF instructions.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Acked-by: Borislav Petkov <petkovbb@googlemail.com>
LKML-Reference: <4A80A5AD.2000209@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Johannes Stezenbach reported that 'perf stat' does not count
cache-miss and cache-references events on his Pentium-M based
laptop.
This is because we left them blank in p6_perfmon_event_map[],
fill them in.
Reported-by: Johannes Stezenbach <js@sig21.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
My Latitude d630 seems to be handling thermal events in SMI by
lowering the max frequency of the CPU till it cools down but
still leaks the "everything is normal" events.
This spams the console and with high priority printks.
Adjust therm_throt driver to only print messages about the fact
that temperatire returned back to normal when leaving the
throttling state.
Also lower the severity of "back to normal" message from
KERN_CRIT to KERN_INFO.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <20090810051513.0558F526EC9@mailhub.coreip.homeip.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reboot does not work on my MacBook Pro 13 inch (MacBookPro5,5)
too. It seems all unibody MacBook and MacBookPro require
PCI reboot handling, i guess.
Following model/machine ID list shows unibody MacBook/Pro have
the 5 series of model number:
http://www.everymac.com/systems/by_capability/macs-by-machine-model-machine-id.html
Signed-off-by: Shunichi Fuji <palglowr@gmail.com>
Cc: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <30046e3b0908101134p6487ddbftd8776e4ddef204be@mail.gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perfcounters-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
perf_counter: Zero dead bytes from ftrace raw samples size alignment
perf_counter: Subtract the buffer size field from the event record size
perf_counter: Require CAP_SYS_ADMIN for raw tracepoint data
perf_counter: Correct PERF_SAMPLE_RAW output
perf tools: callchain: Fix bad rounding of minimum rate
perf_counter tools: Fix libbfd detection for systems with libz dependency
perf: "Longum est iter per praecepta, breve et efficax per exempla"
perf_counter: Fix a race on perf_counter_ctx
perf_counter: Fix tracepoint sampling to be part of generic sampling
perf_counter: Work around gcc warning by initializing tracepoint record unconditionally
perf tools: callchain: Fix sum of percentages to be 100% by displaying amount of ignored chains in fractal mode
perf tools: callchain: Fix 'perf report' display to be callchain by default
perf tools: callchain: Fix spurious 'perf report' warnings: ignore empty callchains
perf record: Fix the -A UI for empty or non-existent perf.data
perf util: Fix do_read() to fail on EOF instead of busy-looping
perf list: Fix the output to not include tracepoints without an id
perf_counter/powerpc: Fix oops on cpus without perf_counter hardware support
perf stat: Fix tool option consistency: rename -S/--scale to -c/--scale
perf report: Add debug help for the finding of symbol bugs - show the symtab origin (DSO, build-id, kernel, etc)
perf report: Fix per task mult-counter stat reporting
...
Wei Chong Tan reported a fast-PIT-calibration corner-case:
| pit_expect_msb() is vulnerable to SMI disturbance corner case
| in some platforms which causes /proc/cpuinfo to show wrong
| CPU MHz value when quick_pit_calibrate() jumps to success
| section.
I think that the real issue isn't even an SMI - but the fact
that in the very last iteration of the loop, there's no
serializing instruction _after_ the last 'rdtsc'. So even in
the absense of SMI's, we do have a situation where the cycle
counter was read without proper serialization.
The last check should be done outside the outer loop, since
_inside_ the outer loop, we'll be testing that the PIT has
the right MSB value has the right value in the next iteration.
So only the _last_ iteration is special, because that's the one
that will not check the PIT MSB value any more, and because the
final 'get_cycles()' isn't serialized.
In other words:
- I'd like to move the PIT MSB check to after the last
iteration, rather than in every iteration
- I think we should comment on the fact that it's also a
serializing instruction and so 'fences in' the TSC read.
Here's a suggested replacement.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
Tested-by: "Tan, Wei Chong" <wei.chong.tan@intel.com>
LKML-Reference: <B28277FD4E0F9247A3D55704C440A140D5D683F3@pgsmsx504.gar.corp.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the following 'make includecheck' warning:
arch/mn10300/include/asm/pci.h: linux/mm.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added REGULATOR, MMC and updated default CMDLINE so RX51 now boots.
Note that the regulator code should be moved from mmc-twl4030.c
to omap_hsmmc.c so it can be a module.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
twl_mmc_cleanup() must free up the regulators that were
allocated by twl_mmc_late_init().
This eliminates the below error when 'omap_hsmmc' module is
repeatedly loaded and unloaded.
"sysfs: cannot create duplicate filename '/devices/platform
/mmci-omap-hs.0/microamps_requested_vmmc'"
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer
dereference during MUSB initialisation.
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes a wrong setting of resource parameter list in
SMSC911x platform driver data structure for Overo case.
This fixes folowing warning when compiling for Overo board:
warning: initialization from incompatible pointer type
Introduced since commit id:
commit 172ef27544
Author: Steve Sakoman <sakoman@gmail.com>
Date: Mon Feb 2 06:27:49 2009 +0000
ARM: Add SMSC911X support to Overo platform (V2)
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit e85c205ac1 increase vmalloc size.
vmalloc space will overlap with OMAP3 sram virtual address.
Signed-off-by: Li Hong Mei <hong-mei.li@motorola.com>
Signed-off-by: Janboe Ye <yuan-bo.ye@motorola.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
This errata is valid for:
OMAP2420 Errata 1.85 Impacts all 2420 ES rev
OMAP2430 Errata 1.10 Impacts only ES1.0
Description: DMA may hang when several channels are used in parallel
OMAP3430: Not impacted, so remove the errata fix for omap3
Fixed issue reported on cpu_is_omap24xx check reported by Nishant Kamat
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to keep these defines limited in the ifdef block
for mach-omap2. It will just cause problems testing for the CPU
revision in the common code, like the next patch does for the DMA
errata.
Signed-off-by: Tony Lindgren <tony@atomide.com>
All we need to do for CONFIG_DMA_API_DEBUG support is call
dma_debug_init() in DMA code common for SPARC32 and SPARC64.
Now SPARC32 uses two dma_map_ops structures for pci and sbus so
there is not much dma stuff for SPARC32 in kernel/dma.c.
kernel/ioport.c also includes dma stuff for SPARC32. So let's
put all the dma stuff for SPARC32 in kernel/ioport.c and make
kernel/dma.c common for SPARC32 and SPARC64.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Robert Reif <reif@earthlink.net>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1249872797-1314-9-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This converts SPARC to use asm-generic/pci-dma-compat instead
of the homegrown mechnism.
SPARC32 has two dma_map_ops structures for pci and sbus
(removing arch/sparc/kernel/dma.c, PCI and SBUS DMA accessor).
The global 'dma_ops' is set to sbus_dma_ops and get_dma_ops()
returns pci32_dma_ops for pci devices so we can use the
appropriate dma mapping operations.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Robert Reif <reif@earthlink.net>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1249872797-1314-8-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is a preparation for using asm-generic/pci-dma-compat.h;
SPARC32 has two dma_map_ops structures for pci and sbus
(removing arch/sparc/kernel/dma.c, PCI and SBUS DMA accessor).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Robert Reif <reif@earthlink.net>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1249872797-1314-7-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now sparc uses include/asm-generic/dma-mapping-common.h.
pci_sun4v.c doesn't need to have no-op
dma_4v_sync_single_for_cpu and dma_4v_sync_sg_for_cpu
(dma-mapping-common.h does nothing if sync_{single|sg}_for_cpu
hook is not defined). So we can remove them safely.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Robert Reif <reif@earthlink.net>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1249872797-1314-6-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
flush_write_buffers() in dma-mapping-common.h was removed so we
can remove NULL flush_write_buffers() in IA64.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
Cc: davem@davemloft.net
LKML-Reference: <1249872797-1314-3-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This moves flush_write_buffers() in
asm-generic/dma-mapping-common.h to
arch/x86/kernel/pci-nommu.c.
The purpose of this patch is that, we can avoid defining NULL
flush_write_buffers() on IA64 and SPARC.
dma-mapping-common.h is used by X86 and IA64 (and SPARC soon)
but only X86 with CONFIG_X86_OOSTORE or CONFIG_X86_PPRO_FENCE
actually uses flush_write_buffers(). CONFIG_X86_OOSTORE or
CONFIG_X86_PPRO_FENCE is usable with only kernel/pci-nommu.c
(that is, not usable with other X86 IOMMU implementations such
as SWIOTLB, VT-d, etc) so we can safely move
flush_write_buffers() in asm-generic/dma-mapping-common.h to
arch/x86/kernel/pci-nommu.c.
The further discussion is:
http://lkml.org/lkml/2009/6/28/104
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: davem@davemloft.net
Cc: tony.luck@intel.com
Cc: fenghua.yu@intel.com
LKML-Reference: <1249872797-1314-2-git-send-email-fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On an iMac G5, the b43 driver is failing to initialise because trying to
set the dma mask to 30-bit fails. Even though there's only 512MiB of RAM
in the machine anyway:
https://bugzilla.redhat.com/show_bug.cgi?id=514787
We should probably let it succeed if the available RAM in the system
doesn't exceed the requested limit.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'kvm-updates/2.6.31' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Avoid redelivery of edge interrupt before next edge
KVM: MMU: limit rmap chain length
KVM: ia64: fix build failures due to ia64/unsigned long mismatches
KVM: Make KVM_HPAGES_PER_HPAGE unsigned long to avoid build error on powerpc
KVM: fix ack not being delivered when msi present
KVM: s390: fix wait_queue handling
KVM: VMX: Fix locking imbalance on emulation failure
KVM: VMX: Fix locking order in handle_invalid_guest_state
KVM: MMU: handle n_free_mmu_pages > n_alloc_mmu_pages in kvm_mmu_change_mmu_pages
KVM: SVM: force new asid on vcpu migration
KVM: x86: verify MTRR/PAT validity
KVM: PIT: fix kpit_elapsed division by zero
KVM: Fix KVM_GET_MSR_INDEX_LIST
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix buffer overflow in efi_init()
x86: Add quirk to make Apple MacBookPro5,1 use reboot=pci
x86: Fix MSI-X initialization by using online_mask for x2apic target_cpus
x86: Fix VMI && stack protector
If we have the powerpc perf_counter backend compiled in, but
the cpu we are running on is one where we don't support the
PMU, we currently oops in hw_perf_group_sched_in if we try to
use any counters, because ppmu is NULL in that case, and we
unconditionally dereference ppmu.
This fixes the problem by adding a check if ppmu is NULL at the
beginning of hw_perf_group_sched_in, and also at the beginning
of the other functions that get called from the perf_counter
core, i.e. hw_perf_disable, hw_perf_enable, and
hw_perf_counter_setup.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: benh@kernel.crashing.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the vendor name (from c16) can be longer than 100 bytes (or missing a
terminating null), then the null is written past the end of vendor[].
Found with Parfait, http://research.sun.com/projects/parfait/
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Ying <ying.huang@intel.com>
MacBookPro5,1 is not able to reboot unless reboot=pci is set.
This patch forces it through a DMI quirk specific to this
device.
Signed-off-by: Ozan Çağlayan <ozan@pardus.org.tr>
LKML-Reference: <1249403971-6543-1-git-send-email-ozan@pardus.org.tr>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
OMAP3EVM uses ISP1504 phy which doesn't require any programming and
thus has to use NOP otg transceiver.
Cleanups being done:
- Remove unwanted code in usb-musb.c file
- Register NOP in OMAP3EVM board file using
usb_nop_xceiv_register().
- Select NOP_USB_XCEIV for OMAP3EVM boards.
- Don't enable TWL4030_USB in omap3_evm_defconfig
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Eino-Ville Talvala <talvala@stanford.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Currently, the machine_flags are stored late in the startup
initialization which results in failing machine type checks
(e.g. for MACHINE_IS_VM).
To allow these checks, store the machine flags in the lowcore
when the machine type has been detected.
Moving the machine_flags to the lowcore has been introduced with
git commit 25097bf153
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the current CPU doesn't support performance counters,
cur_cpu_spec->oprofile_cpu_type can be NULL. The current
perf_counter modules don't test for that case and would thus
crash at boot time.
Bug reported by David Woodhouse.
Reported-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19066.48028.446975.501454@cargo.ozlabs.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Otherwise the host can spend too long traversing an rmap chain, which
happens under a spinlock.
Cc: stable@kernel.org
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
<linux/clk.h> should be included to get the base API prototypes.
This fixes the following sparse warnings:
arch/arm/common/clkdev.c:65:12:
warning: symbol 'clk_get_sys' was not declared. Should it be static?
arch/arm/common/clkdev.c:79:12:
warning: symbol 'clk_get' was not declared. Should it be static?
arch/arm/common/clkdev.c:87:6:
warning: symbol 'clk_put' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
preserve_crunch_context() calls __copy_to_user() which expects the
destination address to be in __user space. setup_sigframe() properly
passes the destination address.
restore_crunch_context() calls __copy_from_user() which expects the
source address to be in __user space. restore_sigframe() properly
passes the source address.
This fixes {preserve/restore}_crunch_context() to accept the
address as __user space and resolves the following sparse warnings:
arch/arm/kernel/signal.c:146:31:
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:1>*to
got struct crunch_sigframe *frame
arch/arm/kernel/signal.c:156:38:
warning: incorrect type in argument 2 (different address spaces)
expected void const [noderef] <asn:1>*from
got struct crunch_sigframe *frame
arch/arm/kernel/signal.c:250:48:
warning: incorrect type in argument 1 (different address spaces)
expected struct crunch_sigframe *frame
got struct crunch_sigframe [noderef] <asn:1>*<noident>
arch/arm/kernel/signal.c:365:49:
warning: incorrect type in argument 1 (different address spaces)
expected struct crunch_sigframe *frame
got struct crunch_sigframe [noderef] <asn:1>*<noident>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Stop referencing CLOCK_TICK_RATE in the KS8695 drivers, rather refer
to a KS8695_CLOCK_RATE.
Issue pointed out by Russell King on arm-linux-kernel mailing list.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If IRQ triggering is enabled, it can trigger a pending interrupt
even for masked interrupts. Any pending GPIO interrupts can
prevent the powerdomain from hitting retention.
Problem found, reported and additional review and testing by Chunquiu
Wang.
Tested-by: Chunquiu Wang <cqwang@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Powerdomain previous state is checked after restoring new states in
suspend. This patch fixes this problem.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use the min/max settings from CPUfreq policy rather than
processor defined min/max settings.
Without this patch, it's possible to scale frequency outside
the current policy range.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use list_add_tail() when adding discovered UART ports. This is so
traversal using list_for_each_entry() will traverse the list in the
order they were found.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch causes the OMAP uarts to honor the sysfs power/wakeup file
for IOPAD wakeups. Before the OMAP was always woken up from off mode
on a rs232 signal change. This patch also creates a different
platform device for each serial port so that the wakeup properties can
be control per port.
By default, IOPAD wakeups are enabled for each UART. To disable,
# echo disabled > /sys/devices/platform/serial8250.0/power/wakeup
Where serial8250.0 can be replaced by .1, or .2 to control the other
ports.
Original idea and original patch from Russ Dill <russ.dill@gmail.com>
Cc: Russ Dill <russ.dill@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
It was possible for an unhandled interrupt to occur if there was incoming
serial traffic during wakeup from suspend. This was caused by the code
in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time,
but not acking its interrupts. Applies on top of PM branch.
Use the PM begin/end hooks to ensure that the "serial idle" interrupts
are disabled during the suspend path. Also, since begin/end hooks are
now used, use the suspend_state that is passed in the begin hook instead
of the enter hook as per the platform_suspend_ops docs.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Streamline the OMAP4 special IRQ assignments by putting inside
normal init loop instead of having a separate loop.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
By default, prevent functional wakeups from inside a module from
waking up the IVA2. Let DSP Bridge code handle this when loaded.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
gpio_get() should return DATAIN register value when the GPIO
is configured as input whereas it should return DATAOUT register
value when the GPIO is configured as output.
Now /sys/kernel/debug/gpio shows proper values for output GPIOs
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminates this compiler warning:
arch/powerpc/kvm/../../../virt/kvm/kvm_main.c:1178: error: integer overflow in expression
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Avi Kivity <avi@redhat.com>
There are two waitqueues in kvm for wait handling:
vcpu->wq for virt/kvm/kvm_main.c and
vpcu->arch.local_int.wq for the s390 specific wait code.
the wait handling in kvm_s390_handle_wait was broken by using different
wait_queues for add_wait queue and remove_wait_queue.
There are two options to fix the problem:
o move all the s390 specific code to vcpu->wq and remove
vcpu->arch.local_int.wq
o move all the s390 specific code to vcpu->arch.local_int.wq
This patch chooses the 2nd variant for two reasons:
o s390 does not use kvm_vcpu_block but implements its own enabled wait
handling.
Having a separate wait_queue make it clear, that our wait mechanism is
different
o the patch is much smaller
Report-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
We have to disable preemption and IRQs on every exit from
handle_invalid_guest_state, otherwise we generate at least a
preempt_disable imbalance.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>