This patch contains CONFIG_SUSPEND support to the SuperH
architecture. If enabled, SuperH Mobile processors will
register their suspend callbacks during boot.
To suspend, use "echo mem > /sys/power/state". To allow
wakeup, make sure "/sys/device/platform/../power/wakeup"
contains "enabled". Additional per-device driver patches
are most likely needed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds PM support to the clock framework.
With this, resume from hibernation is properly supported.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds the clk_set_parent/clk_get_parent routines to the sh
clock framework.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add Suspend-to-disk / swsusp / CONFIG_HIBERNATION support
to the SuperH architecture.
To suspend, use "swapon /dev/sda2; echo disk > /sys/power/state"
To resume, pass "resume=/dev/sda2" on the kernel command line.
The patch "pm: rework includes, remove arch ifdefs V2" is
needed to allow the generic swsusp code to build properly.
Hibernation is not enabled with this patch though, a patch
setting ARCH_HIBERNATION_POSSIBLE will be submitted later.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was accidentally dropped in the multiple vectors per irq conversion.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7763 hardware
blocks such as RTC/SCIF/DMAC/GETHER/PCIC5/MMCIF/SIM/GPIO/USBF.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786 CPU subtype.
While this is a dual-core CPU, only UP is supported for now. L2 cache
support is likewise not yet implemented.
More information on this particular CPU subtype is available at:
http://www.renesas.com/fmwk.jsp?cnt=sh7786_root.jsp&fp=/products/mpumcu/superh_family/sh7780_series/sh7786_group/
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the recent entry.S refactoring, the SH-X3 path had a mov.l for a
register to register copy, resulting in:
AS arch/sh/kernel/cpu/sh4/../sh3/entry.o
arch/sh/kernel/cpu/sh4/../sh3/entry.S: Assembler messages:
arch/sh/kernel/cpu/sh4/../sh3/entry.S:366: Error: invalid operands for opcode
make[3]: *** [arch/sh/kernel/cpu/sh4/../sh3/entry.o] Error 1
Switch it over to a mov to fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7785 hardware
blocks such as SCIF/DMAC/PCIC5/MMCIF/GDTA/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7780 hardware
blocks such as SCIF/RTC/DMAC/PCIC5/MMCIF/FLCTL/GPIO
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh775x hardware
blocks such as SCI/SCIF/RTC/DMAC/TMU2/REF.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Instead of keeping the single vector -> single linux irq mapping
we extend the intc code to support merging of vectors to a single
linux irq. This helps processors such as sh7750, sh7780 and sh7785
which have more vectors than masking ability. With this patch in
place we can modify the intc tables to use one irq per maskable
irq source. Please note the following:
- If multiple vectors share the same enum then only the
first vector will be available as a linux irq.
- Drivers may need to be rewritten to get pending irq
source from the hardware block instead of irq number.
This patch together with the sh7785 specific intc tables solves
DMA controller irq issues related to buggy interrupt masking.
Reported-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Prefetch early exception data. There is unused space in our
exception handler cache line anyway, so this is almost free.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove EXPEVT vector from the stack, lookup_exception_vector()
for sh3/sh4/sh4a is already using k2 to get the vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register restore code in
the following ways:
- break out restore_regs() from restore_all()
- the register saving order is unchanged
- use restore_regs() in sh_bios_handler and restore_all
- document the function
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the sh3/sh4/sh4a register saving code in
the following ways:
- break out prepare_stack_save_dsp() from handle_exception()
- break out save_regs() from handle_exception()
- the register saving order is unchanged
- align new functions to fit in cache lines
- separate exception code from interrupt code
- keep main code flow in a single cache line per exception vector
- use bsr/rts for regular functions (save pr first)
- keep data in one shared cache line (exception_data)
- document the functions
- tie in the hp6xx code
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
GENERIC_TIME still depends on the clocksource bits being there, which is
presently not supported. This allows the CMT clockevent driver to be used
alongside alternate system timers that do not yet provide a clocksource
of their own (MTU2 and so on in the case of SH-2A).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CMT platform data for SuperH Mobile sh7723/sh7722/sh7343/sh7366.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add TMU disable support so we can use other clockevents.
Also, setup the clockevent rating.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rework and simplify the sched_clock and clocksource code. Instead
of registering the clocksource in a shared file we move it into the
tmu driver. Also, add code to handle sched_clock in the case of no
clocksource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The T-bit manipulation for syscall error checking had the side effect of
spuriously returning ERESTART* errno values over EINTR. So, we simplify
the error checking a bit and leave the T-bit alone.
Reported-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes a bug in the FPU exception handler for the FCNVDS instruction.
To get the register number the instruction is shifted right by 9,
though it should be shifted right by 8.
More information at ST Linux bugzilla:
https://bugzilla.stlinux.com/show_bug.cgi?id=4892
Signed-off-by: Giuseppe Di Giore <giuseppe.di-giore@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CPUs define pinmux tables through the optional interface, while boards
that require demux of their own require it explicitly. Roll the Makefile
rules back to depend on GENERIC_GPIO, which covers both cases.
Fixes a link error with an undefined reference to register_pinmux() on
optional platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch optimizes the gpio data register handling for gpio_set_value().
Instead of using the good old spinlock-plus-read-modify-write strategy
we now use a shadow register and atomic operations.
This improves the bitbanging mmc performance on Migo-R from 26 Kbytes/s
to 40 Kbytes/s.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch separates the register read and write functions to
allow lockless gpio_get_value().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch modifies the table based SuperH gpio implementation to
make use of direct table lookups. With this change the functions
gpio_get_value() and gpio_set_value() are O(1).
Tested on Migo-R using bitbanging mmc. Performance is improved from
11 KBytes/s to 26 Kbytes/s.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
unaligned and nonexistent address causes wrong exception
handling in traps_32.c(handle_unaligned_access).
'handle_unalinged_ins' should return -EFAULT if address error
is fixed up with kernel exception table, otherwise
'handle_unaligned_access' increases already fixed program counter
and then crash.
for example
ioctl(fd, TCGETA, (struct termio *)-1)
never return and stay in TASK_UNINTERRUPTIBLE state forever
in my kernel.
Signed-off-by: SUGIOKA Toshinobu <sugioka@itonet.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the sh7343 JPU to user space using uio_pdrv_genirq,
very similar to the sh7722 JPU patch by Hayama-san.
While at it fix up the end of the sh7722 JPU iomem resource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove __attribute__((weak)) from common code sys_pipe implemantation.
IA64, ALPHA, SUPERH (32bit) and SPARC (32bit) have own implemantations
with the same name. Just rename them.
For sys_pipe2 there is no architecture specific implementation.
Cc: Richard Henderson <rth@twiddle.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Impact: build fix
Ingo Molnar wrote:
> tip/arch/blackfin/kernel/irqchip.c: In function 'show_interrupts':
> tip/arch/blackfin/kernel/irqchip.c:85: error: 'struct kernel_stat' has no member named 'irqs'
> make[2]: *** [arch/blackfin/kernel/irqchip.o] Error 1
> make[2]: *** Waiting for unfinished jobs....
>
So could move kstat_irqs array to irq_desc struct.
(s390, m68k, sparc) are not touched yet, because they don't support genirq
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While looking at reducing the amount of architecture namespace pollution
in the generic kernel, I found that asm/irq.h is included in the vast
majority of compilations on ARM (around 650 files.)
Since asm/irq.h includes a sub-architecture include file on ARM, this
causes a negative impact on the ccache's ability to re-use the build
results from other sub-architectures, so we have a desire to reduce the
dependencies on asm/irq.h.
It turns out that a major cause of this is the needless include of
linux/hardirq.h into asm-generic/local.h. The patch below removes this
include, resulting in some 250 to 300 files (around half) of the kernel
then omitting asm/irq.h.
My test builds still succeed, provided two ARM files are fixed
(arch/arm/kernel/traps.c and arch/arm/mm/fault.c) - so there may be
negative impacts for this on other architectures.
Note that x86 does not include asm/irq.h nor linux/hardirq.h in its
asm/local.h, so this patch can be viewed as bringing the generic version
into line with the x86 version.
[kosaki.motohiro@jp.fujitsu.com: add #include <linux/irqflags.h> to acpi/processor_idle.c]
[adobriyan@gmail.com: fix sparc64]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
arch_setup_additional_pages currently gets two arguments, the binary
format descripton and an indication if the process uses an executable
stack or not. The second argument is not used by anybody, it could
be removed without replacement.
What actually does make sense is to pass an indication if the process
uses the elf interpreter or not. The glibc code will not use anything
from the vdso if the process does not use the dynamic linker, so for
statically linked binaries the architecture backend can choose not
to map the vdso.
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add JPU support on Migo-R via UIO. This make use of Magnus's
generic UIO platform driver. Chunk of contiguous memory to hold
intermediate image and compressed data during encode and decode.
Signed-off-by: Takanari Hayama <taki@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We don't really want this enabled by default, but it is still quite
useful for debugging. So, make it conditional and leave it off by
default.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables the same functionality that sh64 has for sh32. When running
on simulated hardware or via remote memory via the debug interface,
memory is gauranteed to be zero on boot already, and skipping the zeroing
of BSS has measurable boot time benefits.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the rest of the boards that were using cf-enabler "generically"
have switched to setting up their mappings on their own, only the mach-se
boards were left using it. All of the cf-enabler using mach-se boards
use a special initialization of the MRSHPC windows rather than going
through the special PTE as other SH-4 platforms do. This consolidates
the MRSHPC setup logic, hooks it up on the boards that care, and gets rid
of any and all remaining references to cf-enabler.
This has been long overdue, as cf-enabler has been the bane of
arch/sh/kernel for the last 7 years. Good riddance.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This can use the same implementation as sh64, the generated assembly is
the same between the new and old version, so there is not much point in
leaving it open coded in inline assembly.
This is preparatory work for future consolidation of the _32/_64
variants.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nothing is using this any more, so get rid of it before anyone gets the
bright idea to start using it again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the reworked kgdb support, we always detach and reinitialize the
stub. This was mostly a feature for handoffs between sh-ipl+g and the
kgdb stub, but virtually no sh-ipl+g versions ever had this working
right in the first place.
Given that the sh-ipl+g stubs in general use today don't even support
the GDB stub, and we have already killed off the special casing in the
sh-sci serial driver, kill off this now unused symbol too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This migrates from the old bitrotted kgdb stub implementation and moves
to the generic stub. In the process support for SH-2/SH-2A is also added,
which the old stub never provided.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently these cases are not handled properly due to the return value
not being passed back. This needs to be correct to get proper behaviour
out of things like the tracehook signal notifier, amongst others.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the sh64 /proc/asids entry to debugfs and enables it for
all SH parts that have debugfs enabled.
On MMU systems this can be used to determine which processes are using
which ASIDs which in turn can be used for finer grained cache tag
analysis.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were left over from some time ago, sh64 never got around to
defining __HAVE_ARCH_TASK_STRUCT_ALLOCATOR during the conversion, and it
has no need to. Kill these off and use the generic versions instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The INTEVT read at interrupt exception entry is uneccessary, as the read
is deferred until we are ready to enter do_IRQ(). The kgdb nmi path still
requires it, so move it there.
Signed-off-by: Aoi Shinkai <shinkoi2005@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the not-so-generic pm code from arch/sh/kernel/pm.c to the
platform directory together with the rest of the hp6xx pm code.
This is done to let non-hp6xx platforms enable CONFIG_PM.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix interrupt values for the first sh7343 SCIF port and
update the configuration to include the remaining 3 ones.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure the 32 KHz r_clk rate gets propagated correctly. Without
this fix the clocks for RTC, CMT, KEYSC and RWDT are stuck at 0 Hz.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the SH-2A FPU based SH7201 processor subtype.
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Description snipped from Steven Rostedt's PPC patch:
When idle is called, interrupts are blocked, but the idle
function will still wake up on an interrupt. The problem is
that the interrupt disabled latency tracer will take this call
to idle as a latency.
This patch disables the latency tracing when going into idle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a simple show_code() that is in turn plugged in to
show_regs() to provide minimal code dumping at the end of the trace.
Built on top of a simple instruction disassembler derived from the
binutils opcode table.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves in the necessary libgcc bits for SUPERH32 and drops the
libgcc linking for the regular targets. This in turn allows us to rip
out quite a few hacks both in sh_ksyms_32 and arch/sh/Makefile.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CC arch/sh/kernel/cpu/clock.o
arch/sh/kernel/cpu/clock.c: In function 'clk_disable':
arch/sh/kernel/cpu/clock.c:156: warning: 'return' with a value, in function returning void
Introduced by ("sh: enable and disable clocks recursively").
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the usb/r8a66597 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the usbf/m66592 driver and
adjust the cpu specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add clock framework support to the sh_mobile i2c driver and
adjust the processor specific code accordingly.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7366 mstpcr bits and information about their parent clocks.
The datasheet is pretty clear about the clocks on this device.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7343 mstpcr bits and information about their parent clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7723 mstpcr bits and information about their parent clocks.
The datasheet is pretty clear about the clocks on this device.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add sh7722 mstpcr bits and information about their parent clocks.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add base code to handle new mstpcr clocks. Make sure clock rates propagate.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
Each SMP arch defines these themselves. Move them to a central
location.
Twists:
1) Some archs (m32, parisc, s390) set possible_map to all 1, so we add a
CONFIG_INIT_ALL_POSSIBLE for this rather than break them.
2) mips and sparc32 '#define cpu_possible_map phys_cpu_present_map'.
Those archs simply have phys_cpu_present_map replaced everywhere.
3) Alpha defined cpu_possible_map to cpu_present_map; this is tricky
so I just manipulate them both in sync.
4) IA64, cris and m32r have gratuitous 'extern cpumask_t cpu_possible_map'
declarations.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Mike Travis <travis@sgi.com>
Cc: ink@jurassic.park.msu.ru
Cc: rmk@arm.linux.org.uk
Cc: starvik@axis.com
Cc: tony.luck@intel.com
Cc: takata@linux-m32r.org
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: paulus@samba.org
Cc: schwidefsky@de.ibm.com
Cc: lethal@linux-sh.org
Cc: wli@holomorphy.com
Cc: davem@davemloft.net
Cc: jdike@addtoit.com
Cc: mingo@redhat.com
Under qemu there is a race between the TDxE read-and-clear and the SCxTDR
write. While on hardware it can be gauranteed that the read-and-clear
will happen prior to the character being written out, no such assumption
can be made under emulation. As this path happens with IRQs off and the
hardware itself doesn't care about the ordering, move the SCxTDR write
until after the read-and-clear.
Signed-off-by: Vladimir Prus <vladimir@codesourcery.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the TMU0 interrupt frequency on suspend/resume.
During the resume the kernel reprograms the TMU0.ClockEvent mode
but if the mode is periodic than the TMU0.TCOR is updated with
a random wrong value without taking care latest valid saved value.
There was no problem with No_HZ system where TMU0.TCOR isn't used.
Signed-off-by: Francesco M. Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes sci type of SH7723 from PORT_SCI to PORT_SCIFA.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch add usb setting for sh 7366
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently there is very little standing in the way of using an SH-4
toolchain for building an SH-2 kernel, and vice versa. Binutils itself
has no limitations whatsoever and supports explicit ISA hinting, which
we already use with varying degrees of success today.
This leaves GCC as the odd one out, due to a rather dubious policy
decision by the GCC folks to not include all of the CPU family variants
in the default list of multilib targets in GCC4. Despite best efforts to
the contrary, libgcc itself already contains awareness of the various CPU
types and remains generally usable, allowing it to safely be referenced
even on a mismatched target (and indeed, explicit ISA tuning by binutils
keeps us honest in terms of ensuring that we do not link incompatible
objects in).
In order to support this, a couple of changes had to be made. Firstly,
the introduction of MAYBE_DECLARE_EXPORT(), which provides a __weak
extern reference for libgcc resident routines when finer-grained
-m<cpu-family> based tuning is not supported by the toolchain. This
fixes up the __sdivsi3_i4i and __udivsi3_i4i references when dealing
with SH-2 kernels linked with an SH-4 libgcc. Secondly, in case where we
are unable to find a suitable match for CPU family tuning but still
have a toolchain that defaults to FP instruction generation, a suitable
nofpu target must be selected. This is accomplished by selecting the
first nofpu multilib target supported by the toolchain, which is
also necessary for selecting the proper libgcc to link against.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch implements pinmux tables for the sh7785 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch improves the support for gpio pins that are hard wired
to either input or output and lack control register association.
A special force enum id is used to allow use without control
register but still mark the gpio pin as input or output.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the pinmux code to use the boolean value for
the function gpio_set_value(). Without this patch values other
than 0 and 1 will result in incorrect GPIO settings.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit 3f5a54e371 ("ftrace: dump out ftrace
buffers to console on panic") added an ftrace buffer dumper that hooks
in to the die notifier chain and dumps out data in the oops path.
Unfortunately SH supported ftrace but didn't support DIE_OOPS, so add
that in and get it building again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh7203.h include paths were missed in the previous update, so switch
the include path to cpu/ as with the rest.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (112 commits)
sh: Move SH-4 CPU headers down one more level.
sh: Only build in gpio.o when CONFIG_GENERIC_GPIO is selected.
sh: Migrate common board headers to mach-common/.
sh: Move the CPU definition headers from asm/ to cpu/.
serial: sh-sci: Add support SCIF of SH7723
video: add sh_mobile_lcdc platform flags
video: remove unused sh_mobile_lcdc platform data
sh: remove consistent alloc cruft
sh: add dynamic crash base address support
sh: reduce Migo-R smc91x overruns
sh: Fix up some merge damage.
Fix debugfs_create_file's error checking method for arch/sh/mm/
Fix debugfs_create_dir's error checking method for arch/sh/kernel/
sh: ap325rxa: Add support RTC RX-8564LC in AP325RXA board
sh: Use sh7720 GPIO on magicpanelr2 board
sh: Add sh7720 pinmux code
sh: Use sh7203 GPIO on rsk7203 board
sh: Add sh7203 pinmux code
sh: Use sh7723 GPIO on AP325RXA board
sh: Add sh7723 pinmux code
...
o elfcorehdr_addr is used by not only the code under CONFIG_PROC_VMCORE
but also by the code which is not inside CONFIG_PROC_VMCORE. For
example, is_kdump_kernel() is used by powerpc code to determine if
kernel is booting after a panic then use previous kernel's TCE table.
So even if CONFIG_PROC_VMCORE is not set in second kernel, one should be
able to correctly determine that we are booting after a panic and setup
calgary iommu accordingly.
o So remove the assumption that elfcorehdr_addr is under
CONFIG_PROC_VMCORE.
o Move definition of elfcorehdr_addr to arch dependent crash files.
(Unfortunately crash dump does not have an arch independent file
otherwise that would have been the best place).
o kexec.c is not the right place as one can Have CRASH_DUMP enabled in
second kernel without KEXEC being enabled.
o I don't see sh setup code parsing the command line for
elfcorehdr_addr. I am wondering how does vmcore interface work on sh.
Anyway, I am atleast defining elfcoredhr_addr so that compilation is not
broken on sh.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The pinmux management is tied in to this code, while it is presently only
used by platforms that select GENERIC_GPIO. The asm/gpio.h definitions
are not referenced when GENERIC_GPIO is disabled, resulting in a build
failure for all of the platforms that don't select it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
debugfs_create_dir() returns NULL if an error occurs, returns -ENODEV
when debugfs is not enabled in the kernel.
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7720 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7203 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7723 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds pinmux and gpio support for the sh7722 processor.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds gpio code together with the pinmux table parser.
In the future we should optimize this and switch back to gpiolib.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up a lot of the PIO/MMIO split. No in-tree platforms were
making use of the MMIO overloading through the machvec (nor have any of
them been in some time), so we just kill all of that off. The ISA I/O
routine wrapping remains unaffected, which remains the only special
casing outside of the iomap API that boards need to think about.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The INTC code will be re-used across different architectures, so move
this out to drivers/sh/ and include/linux/sh_intc.h respectively.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for ftrace to SH. This only includes CONFIG_FTRACE,
and does not handle dynamic ftrace presently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a few trace points across events that are deemed
interesting. This implements a number of trace points:
- The page fault handler / TLB miss
- IPC calls
- Kernel thread creation
The original LTTng patch had the slow-path instrumented, which
fails to account for the vast majority of events. In general
placing this in the fast-path is not a huge performance hit, as
we don't take page faults for kernel addresses.
The other bits of interest are some of the other trap handlers, as
well as the syscall entry/exit (which is better off being handled
through the tracehook API). Most of the other trap handlers are corner
cases where alternate means of notification exist, so there is little
value in placing extra trace points in these locations.
Based on top of the points provided both by the LTTng instrumentation
patch as well as the patch shipping in the ST-Linux tree, albeit in a
stripped down form.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are other places where we want to have access to the trap/exception
number, so move out the lookup_exception_vector() helper. While we're at
it, refactor it slightly to return the vector instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These have been using overrides for ELF_CORE_COPY_TASK_REGS and
ELF_CORE_COPY_FPREGS while the generic versions can be used instead.
Presently the pt_regs are also duplicated across elf_core_copy_regs()
and elf_core_copy_task_regs(), this switches to simply copying out
through elf_core_copy_regs() instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Right now, there is no notifier that is called on a new cpu, before the new
cpu begins processing interrupts/softirqs.
Various kernel function would need that notification, e.g. kvm works around
by calling smp_call_function_single(), rcu polls cpu_online_map.
The patch adds a CPU_STARTING notification. It also adds a helper function
that sends the message to all cpu_chain handlers.
Tested on x86-64.
All other archs are untested. Especially on sparc, I'm not sure if I got
it right.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
All CPUs must have a sensible cpu_clk definition these days, which we can
safely use for deriving the preset loops_per_jiffy. The only odd one out
is SH-5, which hasn't been hammered in to the framework yet.
Based on the ST patch.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is doing a force_sig() SIGTRAP, which is already taken
care of in the generic code if no one asserts NOTIFY_STOP. Switch the
default return to NOTIFY_DONE in the case of unhandled traps, so that
the same trap may pass through to other users on the same die chain.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Not all parts support trapa #0xff, so use something within the debug trap
range that's accessible on all parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Initial support for kprobes/kretprobes for 32-bit SH platforms.
[ General cleanup and some rework for the kretprobe hash lock. -- PFM ]
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the TMU code to allow NO_HZ to work on sh
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the SH4 to convert a subnormal double
into a float by catching the FPE and implementing the FCNVDS
instruction in software.
Signed-off-by: Carl Shaw <carl.shaw@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes a problems with the set up of Linux memory:
- When reserving memory at boot time, the code previously reserved
the bottom page of memory, and then from one page up to the end of
the bootmap. This had the desired effect, but was strictly speaking
wrong, as the one page was actually whatever CONFIG_ZERO_PAGE_OFFSET
had been set to.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The dummy timer needs to be registered on the boot CPU before the
system timer clockevent is registered, or broadcasting doesn't work
as advertized.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks up GENERIC_CLOCKEVENTS_BROADCAST and a dummy local timer,
which we call in to from the timer IPI when no other local timer is
provided.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a generic smp_message_recv() routine (based on the PPC
one), that IPI IRQs can wrap in to.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes a problem within the SH implementation of resume_kernel code,
that implements in assembly the bulk of preempt_schedule_irq function without
taking care of the extra code needed to handle the BKL preemptible.
The patch basically consists of removing this asm code and calling the common
C implementation (see kernel/sched.c) as other archs do.
Another change is the missing 'cli' macro invocation at the beginning of
the resume_kernel.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fix the problem that cannot work semtimedop system call.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The crash kernel entry point is currently checked by the kexec kernel
code and only physical addresses in the reserved memory window are
accepted. This means that we can't pass P2 or P1 addresses as entry
points in the case of crash kernels. This patch makes sure we can start
crash kernels by adding support for physical address entry points.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The reserved crash kernel memory range is currently missing from
/proc/iomem. crashk_res is mistakenly setup after __add_active_range().
Reorder things to make sure the resource shows up in /proc/iomem.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following compile error caused by
commit c459dbf294
(sh: ptrace single stepping cleanups.):
<-- snip -->
...
CC arch/sh/kernel/ptrace_64.o
arch/sh/kernel/ptrace_64.c: In function 'user_disable_single_step':
arch/sh/kernel/ptrace_64.c:134: error: 'regs' undeclared (first use in this function)
arch/sh/kernel/ptrace_64.c:134: error: (Each undeclared identifier is reported only once
arch/sh/kernel/ptrace_64.c:134: error: for each function it appears in.)
...
make[2]: *** [arch/sh/kernel/ptrace_64.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Export sh7723 VEU hardware blocks as VEU2H. The sh7723 VEU2H differs
a bit from the sh7722 VEU so use different names for our UIO devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
rsk7203_defconfig fails to build with the following error:
<-- snip -->
...
LD .tmp_vmlinux1
arch/sh/kernel/built-in.o:(__ksymtab+0xb8): undefined reference to `__udivsi3_i4i'
arch/sh/kernel/built-in.o:(__ksymtab+0xc8): undefined reference to `__sdivsi3_i4i'
make[1]: *** [.tmp_vmlinux1] Error 1
<-- snip -->
That worked with 2.6.26, and these are far less undefined references
than in the cases where libgcc was missing.
[ These symbols are not defined on SH-2 versions of libgcc, so we have to
special case the export there. - Paul ]
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently the NUMA node data isn't saved on kexec. This implements a
simple arch_crash_save_vmcoreinfo() for saving off the relevant data.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-X2 extended mode TLB allows for toggling of the exec bit, so make
sure we are using the right protection bits for module space there
also.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this was always being set to AUDIT_ARCH_SH, which assumes
big endian. Fix this up so that the architecture actually reflects
what we're running on.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the changes in commits:
7d6d637dac4f72c4279e
on powerpc. Adding in TIF_NOTIFY_RESUME, and cleaning up the syscall
tracing to be more generic. This is an incremental step to turning
on tracehook, as well as unifying more of the ptrace and signal code
across the 32/64 split.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the single stepping done by sh/sh64 ptrace implementations
to use the generic user_enable/disable_single_step(), and subsequently
rips out a lot of ptrace request cases that are now handled generically.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
A quick cut and paste from other architectures to allow SH
to parse the elfcorehdr command line argument which is required
for both is_kdump_kernel() and vmcore to function.
(the former is as yet unused on SH).
Tested compilation only
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the sparc changes a439fe51a1.
Most of the moving about was done with Sam's directions at:
http://marc.info/?l=linux-sh&m=121724823706062&w=2
with subsequent hacking and fixups entirely my fault.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Without this patch, signals sent during architecture specific signal
handling (typically as a result of the user's stack being inaccessible)
are ignored.
This is the SH version of commit c3ff8ec31c
which was for the i386.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.
With this change all SuperH Mobile devices now use the same clock code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.
While at it, fix up the VEU(2) interrupt vector.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is
By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize
By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for the single I2C channel on sh7366.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for the single I2C channel on sh7723.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds platform data for two I2C channels to the sh7343.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.
It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains the following cleanups:
- make the following needlessly global code static:
- cf-enabler.c: cf_init()
- cpu/clock.c: __clk_enable()
- cpu/clock.c: __clk_disable()
- process_32.c: default_idle()
- time_32.c: struct clocksource_sh
- timers/timer-tmu.c: struct tmu_timer_ops
- remove the following unused functions (no CONFIG_BLK_DEV_FD on sh):
- process_{32,64}.c: disable_hlt()
- process_{32,64}.c: enable_hlt()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH7763 has 3 SCIF device. Current code supports SCIF0 and 1.
SCIF0 and 1 are same register constitution, but only SCIF2 is different.
I added support of SCIF2.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently this is only linked in for CONFIG_BINFMT_ELF, make it dependent
on CONFIG_ELF_CORE, so it's both selectable there and also linked in for
CONFIG_BINFMT_ELF_FDPIC.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch provides an enhancement to kexec/kdump. It implements the
following features:
- Backup/restore memory used by the original kernel before/after
kexec.
- Save/restore CPU state before/after kexec.
The features of this patch can be used as a general method to call program in
physical mode (paging turning off). This can be used to call BIOS code under
Linux.
kexec-tools needs to be patched to support kexec jump. The patches and
the precompiled kexec can be download from the following URL:
source: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-src_git_kh10.tar.bz2
patches: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec-tools-patches_git_kh10.tar.bz2
binary: http://khibernation.sourceforge.net/download/release_v10/kexec-tools/kexec_git_kh10
Usage example of calling some physical mode code and return:
1. Compile and install patched kernel with following options selected:
CONFIG_X86_32=y
CONFIG_KEXEC=y
CONFIG_PM=y
CONFIG_KEXEC_JUMP=y
2. Build patched kexec-tool or download the pre-built one.
3. Build some physical mode executable named such as "phy_mode"
4. Boot kernel compiled in step 1.
5. Load physical mode executable with /sbin/kexec. The shell command
line can be as follow:
/sbin/kexec --load-preserve-context --args-none phy_mode
6. Call physical mode executable with following shell command line:
/sbin/kexec -e
Implementation point:
To support jumping without reserving memory. One shadow backup page (source
page) is allocated for each page used by kexeced code image (destination
page). When do kexec_load, the image of kexeced code is loaded into source
pages, and before executing, the destination pages and the source pages are
swapped, so the contents of destination pages are backupped. Before jumping
to the kexeced code image and after jumping back to the original kernel, the
destination pages and the source pages are swapped too.
C ABI (calling convention) is used as communication protocol between
kernel and called code.
A flag named KEXEC_PRESERVE_CONTEXT for sys_kexec_load is added to
indicate that the loaded kernel image is used for jumping back.
Now, only the i386 architecture is supported.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arch/mips/kernel/stacktrace.c: Heiko can't type
kthread: reduce stack pressure in create_kthread and kthreadd
fix core/stacktrace changes on avr32, mips, sh
This patch introduces the new syscall pipe2 which is like pipe but it also
takes an additional parameter which takes a flag value. This patch implements
the handling of O_CLOEXEC for the flag. I did not add support for the new
syscall for the architectures which have a special sys_pipe implementation. I
think the maintainers of those archs have the chance to go with the unified
implementation but that's up to them.
The implementation introduces do_pipe_flags. I did that instead of changing
all callers of do_pipe because some of the callers are written in assembler.
I would probably screw up changing the assembly code. To avoid breaking code
do_pipe is now a small wrapper around do_pipe_flags. Once all callers are
changed over to do_pipe_flags the old do_pipe function can be removed.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_pipe2
# ifdef __x86_64__
# define __NR_pipe2 293
# elif defined __i386__
# define __NR_pipe2 331
# else
# error "need __NR_pipe2"
# endif
#endif
int
main (void)
{
int fd[2];
if (syscall (__NR_pipe2, fd, 0) != 0)
{
puts ("pipe2(0) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
printf ("pipe2(0) set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0)
{
puts ("pipe2(O_CLOEXEC) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fixes this type of problem:
CC arch/s390/kernel/stacktrace.o
arch/s390/kernel/stacktrace.c:84: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:84: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:84: warning: parameter names (without types) in function declaration
arch/s390/kernel/stacktrace.c:97: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:97: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:97: warning: parameter names (without types) in function declaration
caused by "stacktrace: export save_stack_trace[_tsk]"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts sh to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single(). Not tested,
but it compiles.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Magnus Damm