mm-armv.c now only contains the pgd allocation/freeing code, so
rename it to have a more sensible filename.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we're going to have mmu.c for code which is specific to the MMU
machines, we might as well move the other MMU initialisation
specific code from mm-armv.c into this new file. This also allows
us to make some functions static.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
nommu does not require the page table manipulation code in the
bootmem initialisation paths. Move this into separate inline
functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM Versatile board PCI config space read routines are broken for byte
accesses. The access uses a byte read, so masking the bottom two bits of the
address is wrong.
I guess this is a cut/paste error from the the halfword code which uses
aligned word access+shift+mask.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ARM XIP_KERNEL map created in devicemaps_init() is wrong.
The map.pfn is rounded down to an even 1MiB section boundary
which results in va/pa translations errors when XIP_PHYS_ADDR
starts on an odd 1MiB boundary and this causes the kernel to
hang. This patch fixes ARM XIP_KERNEL translation errors for
the odd 1MiB XIP_PHYS_ADDR boundary case.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add S3C2412 power management code, and move the
core register saving in from s3c2412.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the AML M5900 series to the list of supported machines in the
arch/arm/mach-s3c2410 directory. This ensures the core peripherals
are registered, and the timer source is configured. if selected in
the kernel config the framebuffer registers and mtd partition
information are set. This version of the patch has corrected
formatting and removed the legacy procfs directory entry.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds support for CONFIG_DEBUG_ICEDCC for ARM11.
Tested on ARM1136 (OMAP2420).
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- Document the meaning for OP_SCALAR, OP_SD and add OP_DD.
- Formatting cleanups
- Remove now redundant code for making compare instructions
operate on scalar values.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
VECITR in Floating-Point Exception register indicates the number of
remaining short vector iterations after a potential exception was
detected.
In case of exception caused by scalar instructions, VECITR is NOT updated.
Therefore emulation for VFP must ignore VECITR field
and treat "veclen" as zero when recognizing scalar instructing.
Signed-off-by: Gen Fukatsu <fukatsu.gen@jp.panasonic.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The documentation for the ZBOOT_ROM_BSS config option describes it as
"The base address of 64KiB of read/write memory in the target for the
ROM-able zImage..." In actuality, it requires more than 100 KiB of
space in addition to enough space to hold the decompressed kernel.
This patch fixes the description in the Kconfig file.
Signed-off-by: Dan Fandrich <dfandrich@intrinsyc.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix thinko in the flush_ptrace_access() "if (expr)" for the ARM
VIPT non-aliasing cache case. We only need to flush cache when
VM_EXEC is set in vma->vm_flags but "if (expr) always evaluates
to true on UP systems for the ARM VIPT non-aliasing cache case.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the IO-Data GLAN Tank, from Martin Michlmayr.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Thecus n2100 (80219-based.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the redundant Modification lines from
the top of the files in arch/arm/mach-s3c2410
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 LCD controller is different enough
to warrant renaming the platform device.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add new machine VSTMS
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linuxtronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the old per-board defconfigs.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add one defconfig for all iop32x boards and one defconfig for all
iop33x boards.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the iop32x code isn't iop321-specific, and the iop33x code isn't
iop331-specfic, do a s/iop321/iop32x/ and s/iop331/iop33x/, and tidy up
the code to conform to the coding style guidelines somewhat better.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Revamp the iop3xx board support: move the support code for each iop
board type into its own file, start using platform serial and platform
physmap flash devices, switch to a per-board time tick rate, and get
rid of the ARCH_EP80219 and STEPD config options by doing the relevant
checks at run time.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Squeeze three instructions out of the iop32x irq demuxer, and nine
out of the iop33x irq demuxer by using the hardware vector generator.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The iop33x loadsp hunk in arch/arm/boot/compressed/head.S serves
no purpose -- remove it.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Implement the gpio_line_{config,get,set} API for iop3xx.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Get rid of the unused IOP3??_IRQ_OFS irq offset define, start IRQ
numbering from zero.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add CP6 enable/disable sequences to the timekeeping code and the IRQ
code. As a result, we can't depend on CP6 access being enabled when
we enter get_irqnr_and_base anymore, so switch the latter over to
using memory-mapped accesses for now.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the iop32x and iop33x code over to the common time implementation,
and remove the (nearly identical) iop32x and iop33x time implementations.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge and rewrite the iop32x/iop33x time code to do lost jiffy
tracking properly, and put the result in plat-iop/time.c.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Switch the iop32x and iop33x code over to the common PCI implementation,
and remove the (nearly identical) iop32x and iop33x PCI implementations.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge the iop32x PCI code and iop33x PCI code into plat-iop/pci.c.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the i2c bits shared between iop32x and iop33x to plat-iop/i2c.c
and include/asm-arm/hardware/iop3xx.h.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce the arch/arm/plat-iop directory, for code shared between the
iop32x and iop33x, and move the common memory map setup bits there.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename CONFIG_ARCH_IOP321 to CONFIG_ARCH_IOP32X and
CONFIG_ARCH_IOP331 to CONFIG_ARCH_IOP33X.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Clear both the EINT and INT status before
going to sleep, otherwise we may end up being
woken by something that was not set in our
wakeup map.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c24xx_va_gpio2 variable is only used
when the S3C2412 and another cpu-type is
being used in the kernel. This patch ensures
it is not set when it is not being used.
Fixes bug report by Thomas Gleixner.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove the S3C2410 specific items out of the
core PM code. Add sysdev driver for all the
S3C24XX series that used the S3C2410 PM code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On stepping A0/A1 of the 80200, invalidating D-cache by line doesn't
clear the dirty bits, which means that if we invalidate a dirty line,
the dirty data can still be written back to memory later on.
To work around this, dma_inv_range() on these two processors is
implemented as dma_flush_range() (i.e. do a clean D-cache line before
doing the invalidate D-cache line.) For this, we currently have a
processor ID check in xscale_dma_inv_range(), but a better solution
is to add a separate cache_fns and proc_info for A0/A1 80200.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Prevent userland from mapping in physical address regions >= 4G by
checking for that in valid_mmap_phys_addr_range().
Unfortunately, we cannot override valid_mmap_phys_addr_range() without
also overriding valid_phys_addr_range(), so copy drivers/char/mem.c's
version of valid_phys_addr_range() over to arch/arm/mm/mmap.c as well.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change to using flush_cache_all() in pm.c and
also remove the need to flush the cache in the
PM code.
This changes the sleep.S code to have an entry
to store the registers for resume, and then a
second entry (after the caches are cleaned)
to do the suspend and resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Seperate the IRQ power management code out of
the pm.c file, and add it to the relevant
system class devices.
Also make the suspend and resume code take
notice of the fact these registers can be
moved by compile time code.
Add fix from Ilya Yanok to also save the
INTSUBMSK over sleep.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
