Remove unneeded conversion from sk to chan.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Reference counter was incremented when starting ack timer but
decremented only when clearing timer, not when timer fired.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There is no need to send RNR immediately when entring local busy.
Also upper layer might clear local busy condition before ack timer
expires saving few cycles for sending RNR.
This also prevents sending two RNRs in some cases where sending one
would be enough i.e received N I-frame can trigger local busy
(sending RNR acking up to N-1 I-frame) and later sending ack (RNR
acking up to N I-frame).
This was affecting TC_ERM_BV_07_C and TC_ERM_BV_22_C with some non
default channel parameters (tx window and receiving buffer sizes).
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
ack_timer should be cleared when sending ACK to avoid acking I-frames
twice.
This commit introduces helper function (only send ack, not clearing
timer) which is used by l2cap_send_ack and l2cap_ack_timeout. This is
to avoid clearing ack timer in timer function.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
SREJ frame with P-bit set acknowledges I-frames numbered up to
(ReqSeq - 1). With this patch P-bit in SREJ is set only when there are
some I-frames to ack.
This fixes ambiguous situation when lost of I-frame with TxSeq=0 would
result in sending SREJ acking all previous I-frames.
Consider following scenario:
TxWindow=3
HostA: sent I-frame TxSeq=0
HostA: sent I-frame TxSeq=1
HostA: sent I-frame TxSeq=2
HostB: missed I-frame TxSeq=0
HostB: received I-frame TxSeq=1
HostB: sent SREJ ReqSeq=0 Pbit=1
HostA: received SREJ ReqSeq=0 Pbit=1 <- All I-frames acked or not?
...
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix the following build warning:
CC [M] net/bluetooth/hci_core.o
net/bluetooth/hci_core.c: In function ‘__check_enable_hs’:
net/bluetooth/hci_core.c:2587: warning: return from incompatible pointer type
module_param in hci_core.c passes 'enable_hs' as bool format, so fix
this variable definition type.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch makes sure that devices with stronger signal (RSSI closer to
0) are sorted first in the resolve list and will therefore get their
names resolved first during device discovery. Since it's more likely
that the device the user is trying to discover has a strong signal due
to its proximity this ensures that the user gets the "device found"
event for it more quickly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The HCI_MGMT flag should not be cleared when resetting a HCI device.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
There's no point in exposing these to user-space (which is what happens
to everything in hdev->flags) so move them to dev_flags instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
As reported by Dan Carpenter this function causes a Sparse warning and
shouldn't be declared inline:
include/net/bluetooth/l2cap.h:837:30 error: marked inline, but without a
definition"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Since we remove the owner field of hci_dev hci_dev_put and __hci_dev_put
do the same so we can merge them into one function. Same for
hci_dev_hold and __hci_dev_hold.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_dev->dev device structure has an internal refcount. This
refcount is used to protect the whole hci_dev object. However, we
currently do not use it. Therefore, if someone calls hci_free_dev() we
currently immediately destroy the hci_dev object because we never took
the device refcount.
This even happens if the hci_dev->refcnt is not 0. In fact, the
hci_dev->refcnt is totally useless in its current state. Therefore, we
simply remove hci_dev->refcnt and instead use hci_dev->dev refcnt.
This fixes all the symptoms and also correctly integrates the device
structure into our bluetooth bus system.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After unregistering an hci_dev object a bluetooth driver does not have
any callbacks in the hci_dev structure left over. Therefore, there is no
need to keep a reference to the module.
Previously, we needed this to protect the hci-destruct callback.
However, this callback is no longer available so we do not need this
owner field, anymore. Drivers now call hci_unregister_dev() and they
are done with the object.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We provide a device-object to other subsystems and we provide our own
release-function. Therefore, the device-object must own a reference to
our module, otherwise the release-function may get deleted before the
device-object does.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Several drivers already provide an empty callback so we can actually
make this optional and then remove all those empty callbacks in the
drivers.
This callback isn't needed at all by most drivers as they can remove
their allocated structures on device disconnect and not on hci
destruction.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds HCI_ACL_TX_TIMEOUT and clear conversion from msec to jiffies
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
After moving L2CAP timers to workqueues l2cap_set_timer expects timeout
value to be specified in jiffies but constants defined in miliseconds
are used. This makes timeouts unreliable when CONFIG_HZ is not set to
1000.
__set_chan_timer macro still uses jiffies as input to avoid multiple
conversions from/to jiffies for sk_sndtimeo value which is already
specified in jiffies.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Ackec-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
sk_sndtime value should be specified in jiffies thus initial value
needs to be converted from miliseconds. Otherwise this timeout is
unreliable when CONFIG_HZ is not set to 1000.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@tieto.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Adds support for Number Of Completed Data Blocks Event.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch adds the necessary logic to perform name lookups after
inquiry completes. This is done by checking for entries in the resolve
list after each inquiry complete and remote name complete HCI event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds proper state tracking to the device discovery process.
This makes it possible to return appropriate errors when trying to stop
a non-active discovery or start discovery when it is already ongoing.
Once name resolving is implemented this also makes it possible to know
what the right action to do is when a remote name lookup is cancelled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This struct is used for not just inquiry caching but also for general
device discovery state tracking so it's better to rename it to something
more appropriate.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
For the remote name state tracking for the management interface to work
the cache needs to be flushed whenever inquiry is started. The
hci_do_inquiry function is only used by the management interface so by
having the flushing done from it ensures that old ioctl based
functionality isn't affected.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
If user-space has already confirmed the name for a remote device we
shouldn't request confirmation again. The simplest way to do this is to
return the name state from hci_inquiry_cache_update (if it is anything
else than unknown then we do not need confirmation from user-space).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds initial support for mgmt_confirm_name. It adds the
necessary tracking of the name state by extending the inquiry cache. The
actual name resolving operation (to be done once inquiry is finished) is
not yet part of this patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
The EIR defines are needed also outside of mgmt.c (e.g. in hci_event.c
to check if EIR data has the complete name) so it's better to have them
in a single public place, i.e. hci.h.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
This makes it possible to use the convenience functions provided for
standard kernel list types and it also makes it easier to extend the use
of the cache for the management interface where e.g. name resolving
control will be needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Most rate control implementations assume .get_rate and .tx_status are only
called once the per-station data has been fully initialized.
minstrel_ht crashes if this assumption is violated.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If you want to use mesh support from mac80211 on a recent
kernel on 2.6.24 you'll run into a name clash when compiling
against include/linux/namei.h, so rename this routine.
/home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c: At top level:
/home/mcgrof/tmp/compat-wireless-3.2.5-1/net/mac80211/mesh_pathtbl.c:342:26: error: conflicting types for ‘path_lookup’
include/linux/namei.h:71:12: note: previous declaration of ‘path_lookup’ was here
Although this could sit as a separate patch in compat-wireless it seems
best to just merge upstream.
Cc: Javier Cardona <javier@cozybit.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@frijolero.org>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When not debugging mac80211 code, station state transitions do not need to
show up in the kernel log.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are situations where we don't have the
necessary rate control information yet for
station entries, e.g. when associating. This
currently doesn't really happen due to the
dummy station handling; explicitly disabling
rate control when it's not initialised will
allow us to remove dummy stations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mac80211 goes to idle-off before starting a scan.
However, some devices that implement hw scan might not
need going idle-off in order to perform a hw scan, and
thus saving some energy and simplifying their state machine.
(Note that this is also the case for sched scan - it
currently doesn't make mac80211 go idle-off)
Add a new flag to indicate support for hw scan while idle.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ridx" is used as an index into the mcs_mask[] array which has
IEEE80211_HT_MCS_MASK_LEN elements.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the IBSS network is RSN-protected, let userspace authorize the stations
instead of adding them as AUTHORIZED by default.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the second part of the auth/assoc redesign,
the mac80211 part. This moves the auth/assoc code
out of the work abstraction and into the MLME, so
that we don't flip channels all the time etc.
The only downside is that when we are associated,
we need to drop the association in order to create
a connection to another AP, but for most drivers
this is actually desirable and the ability to do
was never used by any applications. If we want to
implement resource reservation with FT-OTA, we'd
probably best do it with explicit R-O-C in wpa_s.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is needed by mac80211 to keep a reference
to a BSS alive for the auth process. Remove the
old version of cfg80211_ref_bss() since it's
not actually used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To track authenticated state seems to have been
a design mistake in cfg80211. It is possible to
have out of band authentication (FT), tracking
multiple authentications caused more problems
than it ever helped, and the implementation in
mac80211 is too complex.
Remove all this complexity, and let userspace
do whatever it wants to, mac80211 can deal with
that just fine. Association is still tracked of
course, but authentication no longer is. Local
auth state changes are thus no longer of value,
so ignore them completely.
This will also help implement SAE -- asking the
driver to do an authentication is now almost
equivalent to sending an authentication frame,
with the exception of shared key authentication
which is still handled completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The dummy STA support was added because I didn't
want to change the driver API at the time. Now
that we have state transitions triggering station
add/remove in the driver, we only call add once a
station reaches ASSOCIATED, so we can remove the
dummy station stuff again.
While at it, tighten the RX check and accept only
port control (EAP) frames from the AP station if
it's not associated yet -- in other cases there's
no race.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of maintaining separate sta_add/sta_remove
callsites, implement it in sta_state when the driver
has no sta_state implementation.
The only behavioural change this should cause is in
secure mesh mode: with this the station entries will
only be created after the stations are set to AUTH.
Given which drivers support mesh, this seems to not
be a problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(based on Eliad's patch)
Add a callback to notify the low-level driver whenever
the state of a station changes. The driver is only
notified when the station is actually in the mac80211
hash table, not for pre-insert state transitions.
To allow the driver to replace sta_add/remove calls
with this, call extra transitions with the NOTEXIST
state.
This callback can fail, so we need to be careful in
handling it when a station is inserted, particularly
in the IBSS case where we still keep the station entry
around for mac80211 purposes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be used by drivers later if they
need to have stations inserted all the time,
in mac80211 has no purpose, is never used
and sta_state starts out in NONE.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a station couldn't be uploaded to the driver but
is still kept (only in IBSS mode) we still shouldn't
try to program the keys for it into hardware; fix
this bug by skipping the key upload in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting keys and updating TKIP keys must use the
BSS sdata (not AP_VLAN), so we translate. Move
the translation into driver-ops wrappers instead
of having it inline in the code to simplify the
normal code flow.
The same can be done for sta_add/remove which
already does the translation in the wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the station state modification right before insert,
this just makes the current code more readable (you can
tell that it's before insertion looking at a single
screenful of code) right now, but some upcoming changes
will require this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unted the assumption that the sta struct is still accessible before the
synchronize_rcu call we should move the num_sta_ps counter decrement
after synchronize_rcu to avoid incorrect decrements if num_sta_ps.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle MCS masks set by the user.
* Match rates provided by the rate control algorithm to the mask set,
also in HT mode, and switch back to legacy mode if necessary.
* add debugfs files to observate the rate selection
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow to set mcs masks through nl80211. We also allow to set MCS
rates but no legacy rates (and vice versa).
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver blocked this specific STA with the help of
ieee80211_sta_block_awake we won't clear WLAN_STA_PS_STA later but
still decrement num_sta_ps. Hence, the next data frame from this
STA will trigger ap_sta_ps_end again and also decrement num_sta_ps
again leading to an incorrect num_sta_ps counter.
This can result in problems with powersaving clients not waking up
from PS because the TIM calculation might be skipped due to the
incorrect num_sta_ps counter.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Andrei Emeltchenko