gspca_mr97310a: Allow overriding of detected sensor type
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Use correct register for CIF type 1 sensor gain settings
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Add controls for CIF type 0 sensor cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: make the probing a bit less chatty
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Move detection of CIF sensor type to probe() function,
so that the right controls are set to disabled from the start, rather then
having them disappear all of a sudden when the stream is started.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: cleanup/fixup control handling
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca: mr97310a fix detection of sensortype for vivicam with id byte of 0x53
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds supports for mr97310a camera's with CIF sensors (2 different
types) and for VGA mr97310a camera with a different sensor then supported
until now.
This patch also add support for controls for one of the 2 CIF sensors, this
was written by Thomas Kaiser <thomas@kaiser-linux.li>
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Thomas Kaiser <thomas@kaiser-linux.li>
Signed-off-by: Hans de Goede <hdgoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that we've figured out the higher compression settings (supported in
libv4l-0.6.0 and later, so after this patch the driver should be used with
libv4l-0.6.0 or higher only!), we can enable higher framerates. Which
means lower exposure times, which is important for the use of the pac207
in full daylight.
This patch also tweakes the brightness default and the per color gain
balances to use the values which are adviced by Pixart in the pac207
application note.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_pac207: remove a number of unneeded (repeated) register writes
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- bad sensor power
- bad edge gain/threshold
- set back the auto gain
- light frequency filter inverted
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These changes were a direct result of using a semantic patch
More information can be found at http://www.emn.fr/x-info/coccinelle/
[mchehab@redhat.com: fix a merge conflict]
Signed-off-by: Stoyan Gaydarov <sgayda2@uiuc.edu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On VIDEO_M52790 and USB_GSPCA_SN9C20X, instead of tab, it were
using 7 whitespaces at the beginning, probably due to some
cut-and-paste trouble.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This prevents a loop if a permanent error occurs in usb_set_interface().
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The patches
gspca - vc032x: Add resolution 1280x1024 for sensor mi1310_soc.
gspca - vc032x: Webcam 041e:405b added and mi1310_soc updated.
will make the preview function not work, so I disable the 1280x1024 resolution
and revert back to the origin mi1310_soc settings.
And, using USB snoop tool on Windows to get the correct i2c commands to
turn on/off the LED flash.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* use i2c_w instead of reg_w
* return error on failure
* read the correct number of bytes
Signed-off-by: Brian Johnson <brijohn@gmail.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- call a new subdriver function 'isoc_init' before chosing the first
alternate setting.
- call a new subdriver function 'isoc_nego' when submitting the URBs failed.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only the back sensor (mi1320_soc) is usable.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is not just pure cosmetic, since the order affects the out-of-tree
module build at the -hg development tree.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bug was introduced when adding the light frequency control
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Name saturation control saturation, not color and make the default
less saturated (the old default was overdoing it).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj + ov7630 had the default value for flip enabled, as otherwise
the picture is upside down. It is better to instead invert the meaning
of the control in the set function, and have the default be no vflip,
as one would expect vflip enabled to be upside down.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: enable autogain control for the ov7620, and not only
make it enable autogain but also auto exposure (and do the
same for the ov7648).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: increase 640x480 frame-buffersize, as I was getting buffer
overflows during my testing of a "Premier" 0c45:613e cam
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_sonixj: enable support for 0c45:613e camera, and slightly tweak
the ov7630 register init values for a much better picture.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control index defines for the gspca_sonixj driver were numbered
wrong, causing us to disable the wrong controls on various sensors
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for st6422 bridge and sensor to the stv06xx gspca sub driver,
tested with:
Logitech QuickCam Messenger 046d:08f0 ST6422 integrated
Logitech QuickCam Mess. Plus 046d:08f6 ST6422 integrated
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: Cleanup some sensor special cases
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: add support for the ov511 bridge
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Hmm, another one with an extra if (life sucks) the
default contrast really is no good for the ov6630, it
isn't even high enough in full daylight, this gives
the ov6630 a different initial value for a better out
of the box experience.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported on the ov51x-jpeg list, and as I can confirm with my own cam
the ov7670 in 320x240 has a number of broken columns of pixels
at the left of the picture. This was not present in the old
driver as it always used 640x480 and did software
downscaling (took me a while to figure that one out).
The fix adds a sensor specific if in so far sensor
neutral code :( But this is the only way to fix this,
this cannot be fixed by only changing sensor registers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
My ov519 cam has it led inverted, the same has been
reported on the ov51x-jpeg list for another
creative cam. This patch fixes this without changing
the behaviour for other cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: Add 320x240 and 160x120 support for cif sensor cams
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The fix for the UV swapping in qcif mode with the ov6630, which I did
to fix this issue on a ov518 cam with an ov66308AF, causes UV swapping in
qcif with another cam of mine with the ov518 and an ov66308AE, so this
patch changes the code to differentiate between the ov66308AF and other
ov6630 versions, and restricts the UV swap fix to the ov66308AF.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds autobrightness (so that it can
be turned off to make the already present brightness
control work) and light frequency filtering controls.
The lightfreq control needed 2 different entries
in the ctrls array, as the number of options differs
depending on the sensor. Always one of the 2 entires is
disabled ofcourse.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The scan of the image packets of the sensor ov772x was broken when
the sensor ov965x was added.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Extend the gain range
- Adjust the exposure
- Remove the broken autogain
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The YUYV 640x480 format did not work with ov965x.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The number of packets per isochronous message may now be set by the subdrivers
(default value 32).
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new mechanism does not use any temporary buffer.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A new image may start without any UVC EOF in the last packet of the
previous image.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the bandwidth is not wide enough, the transfer endpoint may be set to
the one of the alternate setting 0. This one may be null and this causes a
divide by 0 oops.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let the subdrivers to set the 'image transfer by bulk' flag.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
s5k83a: All v4l2 ctrls are initialized later, no need to set those registers during init.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replaces some magic constants with the defines. Remove a couple of bits that should be set later in the process depending on the v4l2 ctrl.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds experimental support for QVGA. This is code is compile tested only.
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch for the po1030 sets the drawing window for the VGA resolution
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a prepatory patch in order to support multiple resolutions for the po1030 sensor
Signed-off-by: Erik Andr?n <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>