The sysfs interface allowing user space to disable/enable GPEs
doesn't work correctly, because a GPE disabled this way will be
re-enabled shortly by acpi_ev_asynch_enable_gpe() if it was
previosuly enabled by acpi_enable_gpe() (in which case the
corresponding bit in its enable register's enable_for_run mask is
set).
To address this issue make the sysfs GPE interface use
acpi_enable_gpe() and acpi_disable_gpe() instead of acpi_set_gpe()
so that GPE reference counters are modified by it along with the
values of GPE enable registers.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
While developing the GPE reference counting code we overlooked the
fact that acpi_ev_update_gpes() could have enabled GPEs before
acpi_ev_initialize_gpe_block() was called. As a result, some GPEs
are enabled twice during the initialization.
To fix this issue avoid calling acpi_enable_gpe() from
acpi_ev_initialize_gpe_block() for the GPEs that have nonzero
runtime reference counters.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_hw_write_gpe_enable_reg() to re-enable a GPE after
an event signaled by it has been handled. However, this function
writes the entire GPE enable mask to the GPE's enable register which
may not be correct. Namely, if one of the other GPEs in the same
register was previously enabled by acpi_enable_gpe() and subsequently
disabled using acpi_set_gpe(), acpi_hw_write_gpe_enable_reg() will
re-enable it along with the target GPE.
To fix this issue rework acpi_hw_write_gpe_enable_reg() so that it
calls acpi_hw_low_set_gpe() with a special action value,
ACPI_GPE_COND_ENABLE, that will make it only enable the GPE if the
corresponding bit in its register's enable_for_run mask is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_ev_enable_gpe() for enabling GPEs at the low level,
which is incorrect, because this function only enables the GPE if the
corresponding bit in its enable register's enable_for_run mask is set.
This causes acpi_set_gpe() to work incorrectly if used for enabling
GPEs that were not previously enabled with acpi_enable_gpe(). As a
result, among other things, wakeup-only GPEs are never enabled by
acpi_enable_wakeup_device(), so the devices that use them are unable
to wake up the system.
To fix this issue remove acpi_ev_enable_gpe() and its counterpart
acpi_ev_disable_gpe() and replace acpi_hw_low_disable_gpe() with
acpi_hw_low_set_gpe() that will be used instead to manipulate GPE
enable bits at the low level. Make the users of acpi_ev_enable_gpe()
and acpi_ev_disable_gpe() call acpi_hw_low_set_gpe() instead and
make sure that GPE enable masks are only updated by acpi_enable_gpe()
and acpi_disable_gpe() when GPE reference counters change from 0
to 1 and from 1 to 0, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In quite a few places ACPICA needs to compute a GPE enable mask with
only one bit, corresponding to a given GPE, set. Currently, that
computation is always open coded which leads to unnecessary code
duplication. Fix this by introducing a helper function for computing
one-bit GPE enable masks and using it where appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 0f849d2cc6 (ACPICA: Minimize
the differences between linux GPE code and ACPICA code base)
introduced a change attempting to disable a GPE before installing
a handler for it in acpi_install_gpe_handler() which was incorrect.
First, the GPE disabled by it is never enabled again (except during
resume) which leads to battery insert/remove events not being
reported on the Maxim Levitsky's machine. Second, the disabled
GPE is still reported as enabled by the sysfs interface that only
checks its enable register's enable_for_run mask.
Revert this change for now, because it causes more damage to happen
than the bug it was supposed to fix.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Disable Vista compatibility for Sony VGN-NS50B_L.
https://bugzilla.kernel.org/show_bug.cgi?id=12904#c46
Note that this change is a workaround, not a permanent fix.
For the permanent fix is to figure out what compatibility
means and to actually be compatible...
Tested-by: Voldemar <harestomper@gmail.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
https://bugzilla.kernel.org/show_bug.cgi?id=13931 describes a bug where
a system fails to successfully resume after the second suspend. Maxim
Levitsky discovered that this could be rectified by forcibly saving
and restoring the ACPI non-volatile state. The spec indicates that this
is only required for S4, but testing the behaviour of Windows by adding
an ACPI NVS region to qemu's e820 map and registering a custom memory
read/write handler reveals that it's saved and restored even over suspend
to RAM. We should mimic that behaviour to avoid other broken platforms.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Saving platform non-volatile state may be required for suspend to RAM as
well as hibernation. Move it to more generic code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Patch is against latest Linus master branch and is expected to be
safe bug fix.
You get:
ACPI: HARDWARE addr space,NOT supported yet
for each ACPI defined CPU which status is active, but exceeds
maxcpus= count.
As these "not booted" CPUs do not run an idle routine
and echo X >/proc/acpi/processor/*/throttling did not work
I couldn't find a way to really access not onlined/booted
machines. Still this should get fixed and
/proc/acpi/processor/X dirs of cores exceeding maxcpus
should not show up.
I wonder whether this could get cleaned up by truncating possible cpu mask
and nr_cpu_ids to setup_max_cpus early some day
(and not exporting setup_max_cpus anymore then).
But this needs touching of a lot other places...
Signed-off-by: Thomas Renninger <trenn@suse.de>
CC: travis@sgi.com
CC: linux-acpi@vger.kernel.org
CC: lenb@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_enter_[simple|bm] routines does us to pm tick conversion on every
idle wakeup and the value is only used in /proc/acpi display. We can
store the time in us and convert it into pm ticks before printing instead and
avoid the conversion in the common path.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The C-state idle time is not calculated correctly, which will return the wrong
residency time in C-state. It will have the following effects:
1. The system can't choose the deeper C-state when it is idle next time.
Of course the system power is increased. E.g. On one server machine about 40W
idle power is increased.
2. The powertop shows that it will stay in C0 running state about 95% time
although the system is idle at most time.
2.6.35-rc1 regression caused-by: 2da513f582
(ACPI: Minor cleanup eliminating redundant PMTIMER_TICKS to NS conversion)
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reported-by: Yu Zhidong <zhidong.yu@intel.com>
Tested-by: Yu Zhidong <zhidong.yu@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As suggested in Venki's suggestion in the commit 0dc698b,
add LAPIC unstable detection in the acpi_pad drvier too.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The names of the functions used for blocking/unblocking EC
transactions during suspend/hibernation suggest that the transactions
are suspended and resumed by them, while in fact they are disabled
and enabled. Rename the functions (and the flag used by them) to
better reflect what they really do.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
There still is a race that may result in suspending the system in
the middle of an EC transaction in progress, which leads to problems
(like the kernel thinking that the ACPI global lock is held during
resume while in fact it's not).
To remove the race condition, modify the ACPI platform suspend and
hibernate callbacks so that EC transactions are blocked right after
executing the _PTS global control method and are allowed to happen
again right after the low-level wakeup.
Introduce acpi_pm_freeze() that will disable GPEs, wait until the
event queues are empty and block EC transactions. Use it wherever
GPEs are disabled in preparation for switching local interrupts off.
Introduce acpi_pm_thaw() that will allow EC transactions to happen
again and enable runtime GPEs. Use it to balance acpi_pm_freeze()
wherever necessary.
In addition to that use acpi_ec_resume_transactions_early() to
unblock EC transactions as early as reasonably possible during
resume. Also unblock EC transactions in acpi_hibernation_finish()
and in the analogous suspend routine to make sure that the EC
transactions are enabled in all error paths.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=14668
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
intel_idle: native hardware cpuidle driver for latest Intel processors
ACPI: acpi_idle: touch TS_POLLING only in the non-MWAIT case
acpi_pad: uses MONITOR/MWAIT, so it doesn't need to clear TS_POLLING
sched: clarify commment for TS_POLLING
ACPI: allow a native cpuidle driver to displace ACPI
cpuidle: make cpuidle_curr_driver static
cpuidle: add cpuidle_unregister_driver() error check
cpuidle: fail to register if !CONFIG_CPU_IDLE
acpi pad driver kind of aggressively marks TSC as unstable at init
time, on mwait capable and non X86_FEATURE_NONSTOP_TSC systems. This is
irrespective of whether pad driver is ever going to be used on the
system or deep C-states are supported/used. This will affect every user
who just happens to compile in (or get a kernel version which
compiles in) acpi pad driver.
Move mark_tsc_unstable() out of init to the actual idle invocation path
of the pad driver.
There is also another bug/missing_feature in the code that it does not
support 'always running apic timer' and switches to broadcast mode
unconditionally. Shaohua, can you take a look at that please.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
drivers/acpi/sleep.h:3: WARNING: space prohibited between function name and open parenthesis '('
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_enter_[simple,bm] does
idle timing in ns, convert it to timeval, then to us, then to
pmtimer_ticks and then back to ns.
This patch changes things to
idle timing in ns, convert it to us, and then to pmtimer_ticks.
Just saves an imul along this path, but makes the code cleaner.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This EXPERIMENTAL driver supersedes acpi_idle on
Intel Atom Processors, Intel Core i3/i5/i7 Processors
and associated Intel Xeon processors.
It does not support the Intel Core2 processor or earlier.
For kernels configured with ACPI, CONFIG_INTEL_IDLE=y
allows intel_idle to probe before the ACPI processor driver.
Booting with "intel_idle.max_cstate=0" disables intel_idle
and the system will fall back on ACPI's "acpi_idle".
Typical Linux distributions load ACPI processor module early,
making CONFIG_INTEL_IDLE=m not easily useful on ACPI platforms.
intel_idle probes all processors at module_init time.
Processors that are hot-added later will be limited
to using C1 in idle.
Signed-off-by: Len Brown <len.brown@intel.com>
commit d306ebc286
(ACPI: Be in TS_POLLING state during mwait based C-state entry)
fixed an important power & performance issue where ACPI c2 and c3 C-states
were clearing TS_POLLING even when using MWAIT (ACPI_STATE_FFH).
That bug had been causing us to receive redundant scheduling interrups
when we had already been woken up by MONITOR/MWAIT.
Following up on that...
In the MWAIT case, we don't have to subsequently
check need_resched(), as that c heck was there
for the TS_POLLING-clearing case.
Note that not only does the cpuidle calling function
already check need_resched() before calling us, the
low-level entry into monitor/mwait calls it twice --
guaranteeing that a write to the trigger address
can not go un-noticed.
Also, in this case, we don't have to set TS_POLLING
when we wake, because we never cleared it.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
api_pad exclusively uses MONITOR/MWAIT to sleep in idle,
so it does not need the wakeup IPI during idle sleep
that is provoked by clearing TS_POLLING.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Shaohua Li <shaohua.li@intel.com>
The ACPI driver would fail probe when it found that
another driver had previously registered with cpuidle.
But this is a natural situation, as a native hardware
cpuidle driver should be able to bind instead of ACPI,
and the ACPI processor driver should be able to handle
yielding control of C-states while still handling
P-states and T-states.
Add a KERN_DEBUG line showing when acpi_idle
does successfully register.
Signed-off-by: Len Brown <len.brown@intel.com>
When the user passes the kernel parameter acpi_enforce_resources=lax,
the ACPI resources are no longer protected, so a native driver can
make use of them. In that case, we do not want the asus_atk0110 to be
loaded. Unfortunately, this driver loads automatically due to its
MODULE_DEVICE_TABLE, so the user ends up with two drivers loaded for
the same device - this is bad.
So I suggest that we prevent the asus_atk0110 driver from loading if
acpi_enforce_resources=lax.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Remove own implementation of hex_to_bin().
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These were used before cpuidle by the native ACPI idle driver,
which tracked promotion and demotion between states.
The code was referenced by CONFIG_ACPI_PROCFS
for /proc/acpi/processor/*/power,
but as we no longer do promotion/demotion, that
reference has been a NOP since the transition.
Signed-off-by: Len Brown <len.brown@intel.com>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (22 commits)
ACPI: fix early DSDT dmi check warnings on ia64
ACPICA: Update version to 20100428.
ACPICA: Update/clarify some parameter names associated with acpi_handle
ACPICA: Rename acpi_ex_system_do_suspend->acpi_ex_system_do_sleep
ACPICA: Prevent possible allocation overrun during object copy
ACPICA: Split large file, evgpeblk
ACPICA: Add GPE support for dynamically loaded ACPI tables
ACPICA: Clarify/rename some root table descriptor fields
ACPICA: Update version to 20100331.
ACPICA: Minimize the differences between linux GPE code and ACPICA code base
ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT
ACPICA: Update DSDT copy/detection.
ACPICA: Add subsystem option to force copy of DSDT to local memory
ACPICA: Add detection of corrupted/replaced DSDT
ACPICA: Add write support for DataTable operation regions
ACPICA: Fix for acpi_reallocate_root_table for incorrect root table copy
ACPICA: Update comments/headers, no functional change
ACPICA: Update version to 20100304
ACPICA: Fix for possible fault in acpi_ex_release_mutex
ACPICA: Standardize integer output for ACPICA warnings/errors
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
kasprintf combines kmalloc and sprintf, and takes care of the size
calculation itself.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression a,flag;
expression list args;
statement S;
@@
a =
- \(kmalloc\|kzalloc\)(...,flag)
+ kasprintf(flag,args)
<... when != a
if (a == NULL || ...) S
...>
- sprintf(a,args);
// </smpl>
[akpm@linux-foundation.org: don't change handling of `count']
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
WARNING: at drivers/firmware/dmi_scan.c:423 dmi_matches+0x70/0x160()
dmi check: not initialized yet.
This is caused by commit aa2110c
(ACPI: add boot option acpi=copy_dsdt to fix corrupt DSDT).
DMI is not initialized yet in acpi_early_init on ia64.
The DSDT DMI check table is x86 specific, so make it empty on other archs.
And this fixes the warnings on ia64.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some hardware error injection needs parameters, for example, it is
useful to specify memory address and memory address mask for memory
errors.
Some BIOSes allow parameters to be specified via an unpublished
extension. This patch adds support to it. The parameters will be
ignored on machines without necessary BIOS support.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ERST is a way provided by APEI to save and retrieve hardware error
record to and from some simple persistent storage (such as flash).
The Linux kernel support implementation is quite simple and workable
in NMI context. So it can be used to save hardware error record into
flash in hardware error exception or NMI handler, where other more
complex persistent storage such as disk is not usable. After saving
hardware error records via ERST in hardware error exception or NMI
handler, the error records can be retrieved and logged into disk or
network after a clean reboot.
For more information about ERST, please refer to ACPI Specification
version 4.0, section 17.4.
This patch incorporate fixes from Jin Dongming.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
CC: Jin Dongming <jin.dongming@np.css.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Generic Hardware Error Source provides a way to report platform
hardware errors (such as that from chipset). It works in so called
"Firmware First" mode, that is, hardware errors are reported to
firmware firstly, then reported to Linux by firmware. This way, some
non-standard hardware error registers or non-standard hardware link
can be checked by firmware to produce more valuable hardware error
information for Linux.
Now, only SCI notification type and memory errors are supported. More
notification type and hardware error type will be added later. These
memory errors are reported to user space through /dev/mcelog via
faking a corrected Machine Check, so that the error memory page can be
offlined by /sbin/mcelog if the error count for one page is beyond the
threshold.
On some machines, Machine Check can not report physical address for
some corrected memory errors, but GHES can do that. So this simplified
GHES is implemented firstly.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
CPER stands for Common Platform Error Record, it is the hardware error
record format used to describe platform hardware error by various APEI
tables, such as ERST, BERT and HEST etc.
For more information about CPER, please refer to Appendix N of UEFI
Specification version 2.3.
This patch mainly includes the data structure difinition header file
used by other files.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Hardware Error Device (PNP0C33) is used to report some hardware errors
notified via SCI, mainly the corrected errors. Some APEI Generic
Hardware Error Source (GHES) may use SCI on hardware error device to
notify hardware error to kernel.
After receiving notification from ACPI core, it is forwarded to all
listeners via a notifier chain. The listener such as APEI GHES should
check corresponding error source for new events when notified.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now, a dedicated HEST tabling parsing code is used for PCIE AER
firmware_first setup. It is rebased on general HEST tabling parsing
code of APEI. The firmware_first setup code is moved from PCI core to
AER driver too, because it is only AER related.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Len Brown <len.brown@intel.com>
EINJ provides a hardware error injection mechanism, this is useful for
debugging and testing of other APEI and RAS features.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
HEST describes error sources in detail; communicating operational
parameters (i.e. severity levels, masking bits, and threshold values)
to OS as necessary. It also allows the platform to report error
sources for which OS would typically not implement support (for
example, chipset-specific error registers).
HEST information may be needed by other subsystems. For example, HEST
PCIE AER error source information describes whether a PCIE root port
works in "firmware first" mode, this is needed by general PCIE AER
error subsystem. So a public HEST tabling parsing interface is
provided.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
APEI stands for ACPI Platform Error Interface, which allows to report
errors (for example from the chipset) to the operating system. This
improves NMI handling especially. In addition it supports error
serialization and error injection.
For more information about APEI, please refer to ACPI Specification
version 4.0, chapter 17.
This patch provides some common functions used by more than one APEI
tables, mainly framework of interpreter for EINJ and ERST.
A machine readable language is defined for EINJ and ERST for OS to
execute, and so to drive the firmware to fulfill the corresponding
functions. The machine language for EINJ and ERST is compatible, so a
common framework is defined for them.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some ACPI IO accessing need to be done in atomic context. For example,
APEI ERST operations may be used for permanent storage in hardware
error handler. That is, it may be called in atomic contexts such as
IRQ or NMI, etc. And, ERST/EINJ implement their operations via IO
memory/port accessing. But the IO memory accessing method provided by
ACPI (acpi_read/acpi_write) maps the IO memory during it is accessed,
so it can not be used in atomic context. To solve the issue, the IO
memory should be pre-mapped during EINJ/ERST initializing. A linked
list is used to record which memory area has been mapped, when memory
is accessed in hardware error handler, search the linked list for the
mapped virtual address from the given physical address.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, acpi/irq: Define gsi_end when X86_IO_APIC is undefined
x86, irq: Kill io_apic_renumber_irq
x86, acpi/irq: Handle isa irqs that are not identity mapped to gsi's.
x86, ioapic: Simplify probe_nr_irqs_gsi.
x86, ioapic: Optimize pin_2_irq
x86, ioapic: Move nr_ioapic_registers calculation to mp_register_ioapic.
x86, ioapic: In mpparse use mp_register_ioapic
x86, ioapic: Teach mp_register_ioapic to compute a global gsi_end
x86, ioapic: Fix the types of gsi values
x86, ioapic: Fix io_apic_redir_entries to return the number of entries.
x86, ioapic: Only export mp_find_ioapic and mp_find_ioapic_pin in io_apic.h
x86, acpi/irq: Generalize mp_config_acpi_legacy_irqs
x86, acpi/irq: Fix acpi_sci_ioapic_setup so it has both bus_irq and gsi
x86, acpi/irq: pci device dev->irq is an isa irq not a gsi
x86, acpi/irq: Teach acpi_get_override_irq to take a gsi not an isa_irq
x86, acpi/irq: Introduce apci_isa_irq_to_gsi
The ACPI spec tells us that the firmware will reenable SCI_EN on resume.
Reality disagrees in some cases. The ACPI spec tells us that the only way
to set SCI_EN is via an SMM call.
https://bugzilla.kernel.org/show_bug.cgi?id=13745 shows us that doing so
may break machines. Tracing the ACPI calls made by Windows shows that it
unconditionally sets SCI_EN on resume with a direct register write, and
therefore the overwhelming probability is that everything is fine with
this behaviour.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_hw_set_mode() double checks its effectiveness
by calling acpi_hw_get_mode() -- polling up to 3 seconds.
It would be more logical for its caller, acpi_enable()
acpi_enable() to do the double-checking. (lets assume
that acpi_disable() isn't interesting)
The ACPI specification is unclear on this point.
Some parts say that the BIOS sets SCI_EN and then returns to the OS,
but one part says "OSPM polls the SCI_EN bit until it is sampled SET".
The systems I have on hand do the former,
SCI_EN is observed to be set upon return from the BIOS.
So we move the check up out of acpi_hw_set_mode()
up into acpi_enable() where it makes logical sense.
Then we replace the 3-second polling loop
with a single check. If this check fails, we'll see:
"Hardware did not enter ACPI mode"
and the system will bail out of ACPI initialization
and likely fail to boot. If we see that in practice,
we can restore the polling, but put it into acpi_enable.
This patch is important if acpi_enable() is used in
the resume from S3 path. Many systems today are seen
coming back from S3 with SCI_EN off, and then failing
to set SCI_EN in response to acpi_enable(). Those systems
will take 3 seconds longer to resume due to this loop.
However, it is possible that we will not use acpi_enable()
in the S3 resume path, and bang SCI_EN directly, which
would make the loop harmless, as it would be invisible
to all systems except those that need it.
Signed-off-by: Len Brown <len.brown@intel.com>
Duplicate entries ended up acpisleep_dmi_table[] by accident.
They don't hurt functionality, but they are ugly, so let's get
rid of them.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add Dell Studio models (1558, 1557, 1555) to the 'set_sci_en_on_resume'
list to fix hang on resume.
BugLink: http://bugs.launchpad.net/bugs/553498
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Acked-by: Alex Chiang <achiang@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
Suspend has other meanings in ACPI context, name was misleading.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Original code did not handle the case where the object to be
copied was a namespace node.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Create two new files, evgpeinit.c and evgpeutil.c. Updated
unix and linux makefiles.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For all GPEs, including FADT-based and GPE Block Devices, execute
any _PRW methods in the new table, and process any _Lxx/_Exx GPE
methods in the new table. Any runtime GPE that is referred to
by an _Lxx/_Exx method in the new table is immediately enabled.
ACPICA BZ 833.
http://www.acpica.org/bugzilla/show_bug.cgi?id=833
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Original fields were not very descriptive and led to maintenance
problems. New fields should help to understand the existing code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_hest_firmware_first_pci() could be called when acpi is disabled
and cause system oops.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_device_class can only be 19 characters and a NULL terminator.
With the current name we get a buffer overflow in acpi_smbus_hc_add()
when we do:
strcpy(acpi_device_class(device), ACPI_SMB_HC_CLASS);
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_device_class can only be 19 characters and a NULL terminator.
The current code has a buffer overflow in acpi_power_meter_add():
strcpy(acpi_device_class(device), ACPI_POWER_METER_CLASS);
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: "Darrick J. Wong" <djwong@us.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
cpi_device_class can only be 19 characters and a NULL terminator.
With the current name we get a buffer overflow in acpi_pad_add()
strcpy(acpi_device_class(device), ACPI_PROCESSOR_AGGREGATOR_CLASS);
[akpm@linux-foundation.org: call it acpi_pad, per Shaohua Li]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: walter harms <wharms@bfs.de>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Multiple Lenovo ThinkPad models with Intel Core i5/i7 CPUs can
successfully suspend/resume once, and then hang on the second s/r
cycle.
We got confirmation that this was due to a BIOS defect. The BIOS
did not properly set SCI_EN coming out of S3. The BIOS guys
hinted that The Other Leading OS ignores the fact that hardware
owns the bit and sets it manually.
In any case, an existing DMI table exists for machines where this
defect is a known problem. Lenovo promise to fix their BIOS, but
for folks who either won't or can't upgrade their BIOS, allow
Linux to workaround the issue.
https://bugzilla.kernel.org/show_bug.cgi?id=15407https://bugs.launchpad.net/ubuntu/+source/linux/+bug/532374
Confirmed by numerous testers in the launchpad bug that using
acpi_sleep=sci_force_enable fixes the issue. We add the machines
to acpisleep_dmi_table[] to automatically enable this workaround.
Cc: stable@kernel.org
Cc: Colin King <colin.king@canonical.com>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Strictly speaking on x86 (where acpi is used) dev->irq must be
a dual i8259 irq input aka an isa irq. Therefore we should translate
that isa irq into a gsi before passing it to a function that
takes a gsi.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <1269936436-7039-3-git-send-email-ebiederm@xmission.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This addresses: https://bugzilla.kernel.org/show_bug.cgi?id=14998
We copy some strings into "event" but we leave the space after the NULL
terminators uninitialized. Later in acpi_bus_receive_event() we copy
the whole struct to another buffer with memcpy(). If the new buffer is
stored on the stack, kmemcheck prints a warning about the unitialized
space after the NULL terminators.
It's true that the space is uninitialized, but it's harmless. The
buffer is only used in acpi_system_read_event() and we don't read past
the NULL terminators.
This patch changes the kmalloc() to kzalloc() so that we initialize the
memory and silence the kmemcheck warning.
Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We have ported Rafael's major GPE changes
(ACPI: Use GPE reference counting to support shared GPEs) into ACPICA code base.
But the port and Rafael's original patch have some differences, so we made
below patch to make linux GPE code consistent with ACPICA code base.
Most changes are about comments and coding styles.
Other noticeable changes are based on:
Rafael: Reduce code duplication related to GPE lookup
https://patchwork.kernel.org/patch/86237/
Rafael: Always use the same lock for GPE locking
https://patchwork.kernel.org/patch/90471/
A new field gpe_count in struct acpi_gpe_block_info to record the number
of individual GPEs in block.
Rename acpi_ev_save_method_info to acpi_ev_match_gpe_method.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some BIOS on Toshiba machines corrupt the DSDT, so add a new
boot option acpi=copy_dsdt to workaround it.
Add warning message to ask users to use this option if corrupt DSDT detected.
Also build a DMI blacklist to check it and automatically copy DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move initialization of DSDT pointer. Emit address of DSDT
in the dump of both table headers (good/bad DSDT).
Now handles the case where the root table can be reallocated,
which would invalidate the original pointer.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Optionally copy the entire DSDT to local memory (instead of
simply mapping it.) There are some BIOSs that corrupt or replace
the original DSDT, creating the need for this option. Default is
FALSE, do not copy the DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change adds support to detect a DSDT that has been corrupted
and/or replaced from outside the OS (by firmware). This is
typically catastrophic for the system, but has been seen on
some machines.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The original implementation only supported reading from a DataTable
region. However, some machines have been seen that actually write
to the ACPI table contained in such a region. This change adds
support for writing to a DataTable region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When copying the root table to the new allocation, the length
used was incorrect. The new size was used instead of the current
table size, meaning too much data was copied.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also split some long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with the AML Mutex handling function
acpi_ex_release_mutex where the function could fault under the very
rare condition when the interpreter has blocked, the interpreter
lock is released, the interpreter is then reentered via the
same thread, and attempts to acquire a mutex that was previously
acquired. FreeBSD report 140979.
http://www.freebsd.org/cgi/query-pr.cgi?pr=140979
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Always use 0x prefix for hex output, use %u for integer output
(all integers are unsigned.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will enable debug object output via a global variable,
acpi_gbl_enable_aml_debug_object. This will help with remote machine
debugging. Also, moved all debug object support code to a new
file, exdebug.c. Entire debug object module can now be
configured out of the ACPICA build if desired.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI spec includes a provision for hardware to provide EDID via the
ACPI video extension. In the KMS world it's necessary for a way to obtain
this from within the kernel. Add a function that either returns the EDID
for the provided ACPI display ID or the first display of the provided type.
Also add support for ensuring that devices with legacy IDs are supported.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
access_bit_width field is u8 in ACPICA, thus 256 value written to it
becomes 0, causing divide by zero later.
Proper fix would be to remove access_bit_width at all, just because
we already have access_byte_width, which is access_bit_width / 8.
Limit access width to 64 bit for now.
https://bugzilla.kernel.org/show_bug.cgi?id=15749
fixes regression caused by the fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=14667
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
There is a problem with the ACPI video resume routine that it's
executed before the GPU that may be accessed by it. To fix this
issue, move the ACPI video resume to a power management notifier,
so that's executed after resuming all devices, including the GPU.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15096, which is
a listed regression from 2.6.31.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
By default, ACPI resource conflict messages are logged at level
KERN_ERR. This is a rather high level for a message that is more a
warning than an indication of a real kernel error. Also, KERN_ERR level
messages can appear over some boot splash screens, and this message is
not serious enough to warrant such treatment. Thus, the log level has
been reduced to KERN_WARNING.
[lenb changed to KERN_WARNING rather than all the way to KERN_INFO]
Also, cleanup message to use %pR resource printing format.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Calling kobject_uevent() directly is a layering violation. In
particular, it means we'll miss updating the generic LED trigger.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Disabling CONFIG_ACPI_SYSFS_POWER changes the behaviour of
acpi_battery_update(). It will call acpi_battery_get_info()
even if the battery is not present. I haven't noticed this
causing any problem, but it does look like a bad idea.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
I have a machine here that's sending 0xD1 notifications on the video
device once every second or so. I have no idea why (it's a prototype,
it may be broken), but sending KEY_UNKNOWN is unhelpful and results in
the console becoming unusable. Let's not report keys unless we have
something useful to say about them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pxms are mapped to low node ids to maintain generic kernel use of
functions such as pxm_to_node() that are used to determine device
affinity. Otherwise, there is no pxm-to-node and node-to-pxm matching
rule for x86_64 users of NUMA emulation where a single pxm may be bound
to multiple NUMA nodes.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The acpi_pci_root structure contains all the individual items (acpi_device,
domain, bus number) we pass to pci_acpi_scan_root(), so just pass the
single acpi_pci_root pointer directly.
This will make it easier to add _CBA support later. For _CBA, we need the
entire downstream bus range, not just the base bus number. We have that in
the acpi_pci_root structure, so passing the pointer makes it available to
the arch-specific code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, we only saved the root bus number, i.e., the beginning of the
downstream bus range. We now support IORESOURCE_BUS resources, so this
patch uses that to keep track of both the beginning and the end of the
downstream bus range.
It's important to know both the beginning and the end for supporting _CBA
(see PCI Firmware spec, rev 3.0, sec 4.1.3) and so we know the limits for
any possible PCI bus renumbering (we can't renumber downstream buses to be
outside the bus number range claimed by the host bridge).
It's clear from the spec that the bus range is supposed to be in _CRS, but
if we don't find it there, we'll assume [_BBN - 0xFF] or [0 - 0xFF].
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, we assumed the only Device object immediately below the root
was the \_SB Scope (which the ACPI CA treats as a Device), so we forced
the HID of all such objects to ACPI_BUS_HID ("LNXSYBUS").
However, there are DSDTs that supply root-level Device objects with _HIDs.
This patch makes us pay attention to those _HIDs and only add the synthetic
ACPI_BUS_HID for root-level objects that do not supply their own _HID.
For example, this DSDT: https://bugzilla.kernel.org/show_bug.cgi?id=15605
contains:
Scope (_SB) {
...
}
Device (AMW0) {
Name (_HID, EisaId ("PNP0C14"))
...
}
and we should use "PNP0C14" for the AMW0 device, not "LNXSYBUS".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
On some old IBM workstations and desktop computers, the BIOS presents in the
DSDT an SMBus object that is missing the HID identifier that the i2c-scmi
driver looks for. Modify the ACPI device scan code to insert the missing HID
if it finds an IBM system with such an object.
Affected machines: IntelliStation Z20/Z30. Note that the i2c-i801 driver no
longer works on these machines because of ACPI resource conflicts.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
acpi_ev_enable_gpe() should enable the GPE at the hardware level
regardless of the value of the GPE's runtime reference counter.
There are only two callers of acpi_ev_enable_gpe(), acpi_enable_gpe()
and acpi_set_gpe(). The first one checks the GPE's runtime
reference counter itself and only calls acpi_ev_enable_gpe() if it's
equal to one, and the other one is supposed to enable the GPE
unconditionally (if called with ACPI_GPE_ENABLE).
This change fixes the problem in acpi_enable_wakeup_device() where
the GPE will not be enabled for wakeup if it's runtime reference
counter is zero, which is a regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There may be multiple ACPI dock devices exist in ACPI namespace
and we should probe all of them.
http://bugzilla.kernel.org/show_bug.cgi?id=15521
CC: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Values such as max_brightness should be set before backlights are
registered, but the current API doesn't allow that. Add a parameter to
backlight_device_register and update drivers to ensure that they
set this correctly.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
There's no real need for a pointer to the MADT to be global. The only
function who uses it is map_madt_entry.
This allows us to remove some more ugly #ifdefs.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Un-nest the if statements for readability.
Remove comments that re-state the obvious.
Change the control flow so that we no longer need a temp variable.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Untangle the nested if conditions to make this function look
more similar to the other map_*apic_id() functions.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Untangle the if() statement a little for readability.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that the early _PDC evaluation path knows how to correctly
evaluate _PDC on only physically present processors, there's no
need for the processor driver to evaluate it later when it loads.
To cover the hotplug case, push _PDC evaluation down into the
hotplug paths.
Cc: x86@kernel.org
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that we check for physically present processors before blindly
evaluating _PDC, we no longer need to maintain a DMI opt-in table
nor a kernel param.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Detect if a processor is physically present before evaluating _PDC.
We want this because some BIOS will provide a _PDC even for processors
that are not present. These bogus _PDC methods then attempt to load
non-existent tables, which causes problems.
Avoid those bogus landmines.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Enumerating processors (via MADT/_MAT) belongs in the processor core,
which is always built-in, rather than living in the processor driver
which may not be built.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename static get_cpu_id() to acpi_get_cpuid() and export it.
This change also gives us an opportunity to remove the
#ifndef CONFIG_SMP from processor_driver.c and into a header file
where it properly belongs.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We've renamed the old processor_core.c to processor_driver.c, to
convey the idea that it can be built modular and has driver-like
bits.
Now let's re-create a processor_core.c for the bits needed
statically by the rest of the kernel. The contents of processor_pdc.c
are a good starting spot, so let's just rename that file and
complete our three card monte.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI processor driver can be built as a module. But it has
pieces of code that should always be built statically into the
kernel.
The plan is for processor_core.c to contain the static bits while
processor_driver.c contains the module-like bits.
Since the bulk of the code in the current processor_core.c is
module-like, first step is to rename the file to processor_driver.c
Next step will re-create processor_core.c and cherry-pick out
the static bits.
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi=ht was important in 2003 -- before ACPI was
universally deployed and enabled by default in
the major Linux distributions.
At that time, there were a fair number of people who
or chose to, or needed to, run with acpi=off,
yet also wanted access to Hyper-threading.
Today we find that many invocations of "acpi=ht"
are accidental, and thus is it possible that it
is doing more harm than good.
In 2.6.34, we warn on invocation of acpi=ht.
In 2.6.35, we delete the boot option.
Signed-off-by: Len Brown <len.brown@intel.com>
Right now, if _BQC returns a value we don't understand we immediately
invalidate it. Change this behaviour so we only invalidate it if it
continues to give an invalid answer after we've already set a brightness.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (56 commits)
doc: fix typo in comment explaining rb_tree usage
Remove fs/ntfs/ChangeLog
doc: fix console doc typo
doc: cpuset: Update the cpuset flag file
Fix of spelling in arch/sparc/kernel/leon_kernel.c no longer needed
Remove drivers/parport/ChangeLog
Remove drivers/char/ChangeLog
doc: typo - Table 1-2 should refer to "status", not "statm"
tree-wide: fix typos "ass?o[sc]iac?te" -> "associate" in comments
No need to patch AMD-provided drivers/gpu/drm/radeon/atombios.h
devres/irq: Fix devm_irq_match comment
Remove reference to kthread_create_on_cpu
tree-wide: Assorted spelling fixes
tree-wide: fix 'lenght' typo in comments and code
drm/kms: fix spelling in error message
doc: capitalization and other minor fixes in pnp doc
devres: typo fix s/dev/devm/
Remove redundant trailing semicolons from macros
fix typo "definetly" -> "definitely" in comment
tree-wide: s/widht/width/g typo in comments
...
Fix trivial conflict in Documentation/laptops/00-INDEX
There is a race between resume from hibernation and the EC driver
that may result in restoring the hibernation image in the middle of
an EC transaction in progress, which in turn may lead to
unpredictable behavior of the platform.
To remove that race condition, add a helpers for suspending and
resuming EC transactions in a safe way to be executed by the ACPI
platform hibernate pre-restore and restore cleanup callbacks.
http://bugzilla.kernel.org/show_bug.cgi?id=14668
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These are the non-static sysfs attributes that exist on
my test machine. Fix them to use sysfs_attr_init or
sysfs_bin_attr_init as appropriate. It simply requires
making a sysfs attribute present to see this. So this
is a little bit tedious but otherwise not too bad.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
x86: Fix out of order of gsi
x86: apic: Fix mismerge, add arch_probe_nr_irqs() again
x86, irq: Keep chip_data in create_irq_nr and destroy_irq
xen: Remove unnecessary arch specific xen irq functions.
smp: Use nr_cpus= to set nr_cpu_ids early
x86, irq: Remove arch_probe_nr_irqs
sparseirq: Use radix_tree instead of ptrs array
sparseirq: Change irq_desc_ptrs to static
init: Move radix_tree_init() early
irq: Remove unnecessary bootmem code
x86: Add iMac9,1 to pci_reboot_dmi_table
x86: Convert i8259_lock to raw_spinlock
x86: Convert nmi_lock to raw_spinlock
x86: Convert ioapic_lock and vector_lock to raw_spinlock
x86: Avoid race condition in pci_enable_msix()
x86: Fix SCI on IOAPIC != 0
x86, ia32_aout: do not kill argument mapping
x86, irq: Move __setup_vector_irq() before the first irq enable in cpu online path
x86, irq: Update the vector domain for legacy irqs handled by io-apic
x86, irq: Don't block IRQ0_VECTOR..IRQ15_VECTOR's on all cpu's
...
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (48 commits)
x86/PCI: Prevent mmconfig memory corruption
ACPI: Use GPE reference counting to support shared GPEs
x86/PCI: use host bridge _CRS info by default on 2008 and newer machines
PCI: augment bus resource table with a list
PCI: add pci_bus_for_each_resource(), remove direct bus->resource[] refs
PCI: read bridge windows before filling in subtractive decode resources
PCI: split up pci_read_bridge_bases()
PCIe PME: use pci_pcie_cap()
PCI PM: Run-time callbacks for PCI bus type
PCIe PME: use pci_is_pcie()
PCI / ACPI / PM: Platform support for PCI PME wake-up
ACPI / ACPICA: Multiple system notify handlers per device
ACPI / PM: Add more run-time wake-up fields
ACPI: Use GPE reference counting to support shared GPEs
PCI PM: Make it possible to force using INTx for PCIe PME signaling
PCI PM: PCIe PME root port service driver
PCI PM: Add function for checking PME status of devices
PCI: mark is_pcie obsolete
PCI: set PCI_PREF_RANGE_TYPE_64 in pci_bridge_check_ranges
PCI: pciehp: second try to get big range for pcie devices
...
To fix a bug and address the reviewers' comments regarding the ACPI
GPE refcounting patch, do the following additional changes:
o Remove the second argument of acpi_ev_enable_gpe(),
'write_to_hardware', because it is not necessary any more.
o Add the "bad parameter" test against 'type' in
acpi_enable_gpe() and acpi_disable_gpe().
o Make acpi_enable_gpe() only check 'status' for runtime GPEs if
acpi_ev_enable_gpe() was actually called.
o Make acpi_disable_gpe() return 'status' returned by
acpi_ev_disable_gpe() and fix a bug where ACPI_GPE_TYPE_WAKE
and ACPI_GPE_TYPE_RUNTIME were exchanged by mistake.
o Add comments explaining why acpi_set_gpe() is used by the ACPI EC
driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The main benefit of using ACPI host bridge window information is that
we can do better resource allocation in systems with multiple host bridges,
e.g., http://bugzilla.kernel.org/show_bug.cgi?id=14183
Sometimes we need _CRS information even if we only have one host bridge,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/341681
Most of these systems are relatively new, so this patch turns on
"pci=use_crs" only on machines with a BIOS date of 2008 or newer.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
V2: Corrected integer/long conversion.
Some BIOSes return a negative value for the critical trip point.
Especially since Windows 2006...
We currently invalidate the whole thermal zone in this case.
But it may still be needed for cooling, also without critical
trip point.
This patch invalidates the critical trip point if no _CRT
function is found or if it returns negative values, but does
not invalidate the whole thermal zone in this case.
Reference: http://bugzilla.novell.com/show_bug.cgi?id=531547
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: clarkt@cnsp.com
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Although the majority of PCI devices can generate PMEs that in
principle may be used to wake up devices suspended at run time,
platform support is generally necessary to convert PMEs into wake-up
events that can be delivered to the kernel. If ACPI is used for this
purpose, PME signals generated by a PCI device will trigger the ACPI
GPE associated with the device to generate an ACPI wake-up event that
we can set up a handler for, provided that everything is configured
correctly.
Unfortunately, the subset of PCI devices that have GPEs associated
with them is quite limited. The devices without dedicated GPEs have
to rely on the GPEs associated with other devices (in the majority of
cases their upstream bridges and, possibly, the root bridge) to
generate ACPI wake-up events in response to PME signals from them.
Add ACPI platform support for PCI PME wake-up:
o Add a framework making is possible to use ACPI system notify
handlers for run-time PM.
o Add new PCI platform callback ->run_wake() to struct
pci_platform_pm_ops allowing us to enable/disable the platform to
generate wake-up events for given device. Implemet this callback
for the ACPI platform.
o Define ACPI wake-up handlers for PCI devices and PCI root buses and
make the PCI-ACPI binding code register wake-up notifiers for all
PCI devices present in the ACPI tables.
o Add function pci_dev_run_wake() which can be used by PCI drivers to
check if given device is capable of generating wake-up events at
run time.
Developed in cooperation with Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently it only is possible to install one system notify handler
per namespace node, but this is not enough for PCI run-time power
management, because we need to install power management notifiers for
devices that already have hotplug notifiers installed. While in
principle this could be handled at the PCI level, that would be
suboptimal due to the way in which the ACPI-based PCI hotplug code is
designed.
For this reason, modify ACPICA so that it is possible to install more
than one system notify handler per namespace node. Namely, make
acpi_install_notify_handler(), acpi_remove_notify_handler() and
acpi_ev_notify_dispatch() use a list of system notify handler objects
associated with a namespace node.
Make acpi_remove_notify_handler() call acpi_os_wait_events_complete()
upfront to avoid a situation in which concurrent instance of
acpi_remove_notify_handler() removes the handler from under us while
we're waiting for the event queues to flush.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the run_wake flag to mark all devices for which run-time wake-up
events may be generated by the platform. Introduce a new wake-up
flag, always_enabled, for marking devices that should be permanently
enabled to generate run-time events. Also, introduce a reference
counter for run-wake devices and a function that will initialize all
of the run-time wake-up fields for given device.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI GPEs may map to multiple devices. The current GPE interface
only provides a mechanism for enabling and disabling GPEs, making
it difficult to change the state of GPEs at runtime without extensive
cooperation between devices.
Add an API to allow devices to indicate whether or not they want
their device's GPE to be enabled for both runtime and wakeup events.
Remove the old GPE type handling entirely, which gets rid of various
quirks, like the implicit disabling with GPE type setting. This
requires a small amount of rework in order to ensure that non-wake
GPEs are enabled by default to preserve existing behaviour.
Based on patches from Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI deep C-state entry had a long standing bug/missing feature, wherein we were sending
resched IPIs when an idle CPU is in mwait based deep C-state. Only mwait based C1 was using
the write to the monitored address to wake up mwait'ing CPU.
This patch changes the code to retain TS_POLLING bit if we are entering an mwait based
deep C-state.
The patch has been verified to reduce the number of resched IPIs in general and also
improves the performance/power on workloads with low system utilization (i.e., when mwait based
deep C-states are being used).
Fixes "netperf ~50% regression with 2.6.33-rc1, bisect to 1b9508f"
http://marc.info/?l=linux-kernel&m=126441481427331&w=4
Reported-by: Lin Ming <ming.m.lin@intel.com>
Tested-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPI spec says (11.5 Thermal Zone Interface Requirements):
A thermal zone must contain at least one trip point
(critical, near critical, active, or passive)
Check this once at init time.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: clarkt@cnsp.com
Signed-off-by: Len Brown <len.brown@intel.com>
Earlier, Ingo Molnar posted a patch to make it so that the kernel would avoid
reading _PPC on his broken T60. Unfortunately, it seems that with Thomas
Renninger's patch last July to eliminate _PPC evaluations when the processor
driver loads, the kernel never actually reads _PPC at all! This is problematic
if you happen to boot your non-T60 computer in a state where the BIOS _wants_
_PPC to be something other than zero.
So, put the _PPC evaluation back into acpi_processor_get_performance_info if
ignore_ppc isn't 1.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We broke "acpi=ht" in 2.6.32 by disabling MADT parsing
for acpi=disabled. e5b8fc6ac1
This also broke systems which invoked acpi=ht via DMI blacklist.
acpi=ht is a really ugly hack,
but restore it for those that still use it.
http://bugzilla.kernel.org/show_bug.cgi?id=14886
Signed-off-by: Len Brown <len.brown@intel.com>
On x86, before prefill_possible_map(), nr_cpu_ids will be NR_CPUS aka
CONFIG_NR_CPUS.
Add nr_cpus= to set nr_cpu_ids. so we can simulate cpus <=8 are installed on
normal config.
-v2: accordging to Christoph, acpi_numa_init should use nr_cpu_ids in stead of
NR_CPUS.
-v3: add doc in kernel-parameters.txt according to Andrew.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-34-git-send-email-yinghai@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Tony Luck <tony.luck@intel.com>
Add __percpu sparse annotations to places which didn't make it in one
of the previous patches. All converions are trivial.
These annotations are to make sparse consider percpu variables to be
in a different address space and warn if accessed without going
through percpu accessors. This patch doesn't affect normal builds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Since the rewrite of the CPU idle governor in 2.6.32, two laptops have
surfaced where the BIOS advertises a C2 power state, but for some reason
this state is not functioning (as verified in both cases by powertop
before the patch in .32).
The old governor had the accidental behavior that if a non-working state
was chosen too many times, it would end up falling back to C1. The new
governor works differently and this accidental behavior is no longer
there; the result is a high temperature on these two machines.
This patch adds these 2 machines to the DMI table for C state anomalies;
by just not using C2 both these machines are better off (the TSC can be
used instead of the pm timer, giving a performance boost for example).
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=14742
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Reported-by: <akwatts@ymail.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit fe06fba2 (ACPI: dock: add struct dock_station * directly
to platform device data) changed dock_add() to use the
platform_device_register_data() API.
We passed that interface a stack variable, which is kmemdup'ed
and assigned to the device's platform_data pointer.
Unfortunately, whatever random garbage is in the stack variable
gets coped during the kmemdup, and that leads to broken behavior.
Explicitly zero out the structure before passing it to the API.
This fixes the T41 docking button issue:
http://bugzilla.kernel.org/show_bug.cgi?id=15000
Cc: stable@kernel.org
Reported-by: Chris Mason <chris.mason@oracle.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
trivial, leftover from my NULL pointer dereference patch which got
'superseded' by commit fbc3be2
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Dan's list contains:
drivers/acpi/processor_throttling.c +1139 acpi_processor_get_throttling_info(11) warning: variable derefenced before check 'pr'
acpi_processor_get_throttling_info() is never called with pr == NULL.
[ bart: the potential NULL pointer dereference was finally fixed in
(much later than mine) commit 5cfa245 but my patch is still valid ]
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Roel found a logic issue in the #if 0 acpi_evaluate_string():
- || (element->type != ACPI_TYPE_BUFFER)
+ && (element->type != ACPI_TYPE_BUFFER)
delete the dead code.
pointed-out-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown