When we scan several nand chips with nand_scan(), such as
.......................
nand_scan(*, 2);
.......................
In nand_scan_ident(), the maxchips will become 2, so the current code
will select chip 1 to read the device ID. But the chip 0 is still
selected in this case.
To make the logic clear, we'd better de-select the chip when it is not used.
This patch de-select the nand chip if it is not used any more.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
'set' is tested for NULL. But subsequently accessed without the check.
Thus making it conditional to avoid NULL pointer dereferencing.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
linux,mtd-name allow to specify the mtd name for retro capability with
physmap-flash drivers as boot loader pass the mtd partition via the old
device name physmap-flash.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
IFC_FIR_OP_CMD0 issues command for execution without checking flash
readiness. It may cause problem if flash is not ready. Instead use
IFC_FIR_OP_CW0 which Wait for tWB time and poll R/B to return high or
time-out, before issuing command.
NAND_CMD_READID command implemention does not fulfill above requirement. So
update its programming.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Hemant Nautiyal <hemant.nautiyal@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Enabling the diskonchip drivers on most architectures results
in a pointless warning "#warning Unknown architecture for
DiskOnChip. No default probe locations defined". The driver
can in fact handle the default location already through the
CONFIG_MTD_DOCPROBE_ADDRESS, which gets set on the platforms
that need it, and we get a run-time error if this is not
set correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch allow to detect buggy driver/hardware with
bad RnB (dev_ready) management or when timeout occurs in polling mode.
This works when dev_ready is set or not set.
There are 2 methods to wait for an erase/program command completion:
1. Wait until nand RnB pin goes high (that's what chip->dev_ready usually does)
2. Poll the device: send a status (0x70) command and read status byte in a loop
until bit NAND_STATUS_READY is set
In all cases, you should send a status command after completion, to check if
the operation was successful. And if the operation completed, the status should
have bit NAND_STATUS_READY set.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Enhance the driver to support partition subnodes inside the nand
device bindings to describe partions on the nand device.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
When the kernel parses the following cmdline
#mtdparts=gpmi-nand:16m(boot),16m(kernel),1g(home),4g(test),-(usr)
for a big nand chip Micron MT29F64G08AFAAAWP(8GB), we got the following wrong
result:
.............................................
"mtd: partition size too small (0)"
.............................................
We can not get any partition.
The "4g(test)" partition triggers a overflow of the "size". The memparse()
returns 4g to the "size", but the size is "unsigned long" type, so a overflow
occurs, the "size" becomes zero in the end.
This patch changes the "size"/"offset" to "unsigned long long" type,
and replaces the UINT_MAX with ULLONG_MAX for macros SIZE_REMAINING and
OFFSET_CONTINUOUS.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The current version on mtdoops erase first block of mtdoops partition at each
boot if there is no oops stored in flash. This can wear the flash.
When mtdoops start, find_next_position is called to find the next free entry in
the circular buffer. But if the flash is erased, find_next_position don't find
anything (maxcount == 0xffffffff) and start with the first entry after erasing it.
The scanning that is done in find_next_position already track free/used entries.
So if at the end of the scanning we don't find anything, we can start at the
first entry and erased the entry only if it is marked as used.
Most of this is implemented in mtdoops_inc_counter, so to avoid duplicating
code, if we don't find anything we set position to -1. mtdoops_inc_counter with
increment it, erase the entry if needed and start as before with nextpage = 0
and nextcount = 1).
Also during the scan phase, we use the MTDOOPS_KERNMSG_MAGIC to detect corruped
entries.
Signed-off-by: Matthieu Castet <matthieu.castet@parrot@com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The flctl can now be probed via device tree setup in addition to the
existing platform data way.
SoC specific setup data is set in the .data member of the OF match, so
kept within the driver itself, while board/user specific setup - like
partitioning - is taken from the device tree.
Actual configuration is added for the SoC sh7372.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The code probes if DMA channels can get allocated and tears them down at
removal/failure if needed.
If available it uses them to transfer the data part (not ECC). On
failure we fall back to PIO mode.
Based on Guennadi Liakhovetski's code from the sh_mmcif driver.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some small fixes to avoid sparse and smatch complain. Other cosmetic fixes
as well.
- Change of the type of the member index in struct sh_flctl from signed
to unsigned. We use index by addressing array members, so unsigned is more
concise here. Adapt functions relying on sh_flctl::index.
- Remove a blurring cast in write_fiforeg().
- Apply consistent naming scheme when refering to the data buffer.
- Shorten some unnecessarily verbose functions.
- Remove spaces at start of lines.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The whole gpmi-nand driver has turned to pure devicetree supported.
So the linux/mtd/gpmi-nand.h is not neccessary now. Just remove it,
and move some macros to the gpmi-nand driver itself.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
In some configurations of "gpio-nand" RDY-pin may be not connected.
This patch allow to use driver for these configurations. In this case
we are assume that device always ready.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use the NAND_STATUS_FAIL to replace the hardcode "0x01",
which make the code more readable.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use pr_info() and pr_err() while defining pr_fmt(). This saves a few
characters, joins a few lines, and makes the code a little more readable
(and grep-able).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use KBUILD_MODNAME instead of hardcoding the filename
Signed-off-by: Vikram Narayanan <vikram186@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Use relaxed variants of readl/writel accessors. readl/writel io accessors use
explicit dsb instruction which causes stalls in the processor core resulting
several cycles of delay for each access
Use relaxed variants where ever possible. This also results in an improved
read/write performance.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Interruptible wait caused trouble in fsmc hardware state machine if the
application was killed abruptly. To make fsmc operation safe turn wait in to
un-interruptible.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The nomadik_nand driver is really just a subset of the FSMC
NAND driver, and there are no users anymore so let's delete
it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Add a device tree version of the Denali NAND driver. Based
on an original patch from Jamie Iles to add a MMIO version
of this driver.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The Denali controller can also be found in SoC devices attached to a
simple bus. Move the PCI specific parts into denali_pci so that we can
add a denali_dt that uses the same driver but for a device tree driver
instead of a PCI based device.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Since the introduction of nand_create_default_bbt_descr() (now known as
nand_create_badblock_pattern()) in
commit 58373ff0af
nand_chip.badblock_pattern will be dynamically calculated to the same
1-byte-length pattern that is required by fsl_elbc_nand. This custom
badblock_pattern is no longer needed, then, and its removal may help
facilitate further nand_bbt.c/nand_base.c cleanup in the future (one
down, many to go?)
Anyway, with nand_bbt.c fixed, this effectively reverts:
commit 452db27243
[MTD] [NAND] fsl_elbc_nand: fix OOB workability for large page NAND chips
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The pointer returned by kzalloc should be tested for NULL
to avoid potential NULL pointer dereference later. Incorrect
pointer was being tested for NULL. Bug introduced by commit fbcf62a3
(mtd: physmap_of: move parse_obsolete_partitions to become separate
parser).
This patch fixes this bug.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: stable@vger.kernel.org [3.2+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Simply 'parse_cmdline_partitions': the outer loop iterating over
'partitions' is actually a search loop, it does not execute the inner
loop for each partition, only for the matched partition.
Let's break when search is successful, and move all inner code (relevant
only for the matched partition) outside of the outer loop.
Resulting code is much more readable, and makes the indent level sane.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch fixes errors seen in identifying old Samsung SLC, due to the
following commits:
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
Some Samsung NAND with "5-byte" ID really appear to have 6-byte IDs, with
wraparound like:
Samsung K9K8G08U0D
ec d3 51 95 58 ec ec d3
Samsung K9F1G08U0C
ec f1 00 95 40 ec ec f1
Samsung K9F2G08U0B
ec da 10 95 44 00 ec da
This bad wraparound makes it hard to reliably detect the difference
between Samsung SLC with 5-byte ID and Samsung SLC with 6-byte ID.
The fix is to, for now, only use the new Samsung table for MLC. We
cannot support the new SLC (K9FAG08U0M) until Samsung gives better ID
decode information.
Note that this applies in addition to the previous regression fix:
commit bc86cf7af2
mtd: nand: fix Samsung SLC NAND identification regression
Together, these patches completely restore the previous detection
behavior so that we cannot see any more regressions in Samsung SLC NAND
(finger crossed). With luck, I can get a hold of a Samsung
representative and stop having to cross my fingers eventually.
Reported-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Tested-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
A combination of the following two commits caused a regression in 3.7-rc1
when identifying some Samsung NAND, so that some previously working NAND
were no longer detected properly:
commit e3b88bd604
mtd: nand: add generic READ ID length calculation functions
commit e2d3a35ee4
mtd: nand: detect Samsung K9GBG08U0A, K9GAG08U0F ID
Particularly, a regression was seen on Samsung K9F2G08U0B, with the
following full 8-byte READ ID string:
ec da 10 95 44 00 ec da
The basic problem is that Samsung manufactures both SLC and MLC NAND
that use a non-standard decoding table for deriving information from
their IDs. I have heuristically determined that all the chips that use
the new table have ID strings which wrap around after the 6th byte.
Unfortunately, I overlooked the fact that some older Samsung SLC (which
use a different decoding table) have "5 byte ID strings" which also wrap
around after the 6th byte.
This patch re-introduces a distinction between these old and new Samsung
NAND by checking that the 6th byte is non-zero, allowing both old and
new Samsung NAND to be detected properly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Brian Norris <computersforpeace@gmail.com>
Reported-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Fixes the following sparse warning:
drivers/mtd/onenand/onenand_base.c:3697:5: warning:
symbol 'flexonenand_set_boundary' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This code was broken because it assumed that all MTD devices were map-based.
Disable it for now, until it can be fixed properly for the next merge window.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When transparent huge pages were introduced, memory compaction and swap
storms were an issue, and the kernel had to be careful to not make THP
allocations cause pageout or compaction.
Now that we have working compaction deferral, kswapd is smart enough to
invoke compaction and the quadratic behaviour around isolate_free_pages
has been fixed, it should be safe to remove __GFP_NO_KSWAPD.
[minchan@kernel.org: Comment fix]
[mgorman@suse.de: Avoid direct reclaim for deferred compaction]
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Weinberger from Linutronix. Fastmap is designed to address UBI's slow scanning
issues. Namely, it introduces a new on-flash data-structure called "fastmap",
which stores the information about logical<->physical eraseblocks mappings.
So now to get this information just read the fastmap, instead of doing full
scan. More information here can be found in Richard's announcement in LKML
(Subject: UBI: Fastmap request for inclusion (v19)):
http://thread.gmane.org/gmane.linux.kernel/1364922/focus=1369109
One thing I want to explicitly say is that fastmap did not have large
enough linux-next exposure. It is partially my fault - I did not respond
quickly enough. I _really_ apologize for this. But it had good testing and
disabled by default, so I do not expect that we'll break anything.
Fastmap is declared as experimental so far, and it is off by default. We
did declare that the on-flash format may be changed. The reason for this is
that no one used it in real production so far, so there is a high risk that
something is missing. Besides, we do not have user-space tools supporting
fastmap so far.
Nevertheless, I suggest we merge this feature. Many people want UBI's scanning
bottleneck to be fixed and merging fastmap now should accelerate its production
use. The plan is to make it bullet-prove, somewhat clean-up, and make it the
default for UBI. I do not know how many kernel releases will it take.
Basically, I what I want to do for fastmap is something like Linus did for
btrfs few years ago.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/Sqc
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.7-rc1-fastmap' of git://git.infradead.org/linux-ubi
Pull UBI fastmap changes from Artem Bityutskiy:
"This pull request contains the UBI fastmap support implemented by
Richard Weinberger from Linutronix. Fastmap is designed to address
UBI's slow scanning issues. Namely, it introduces a new on-flash
data-structure called "fastmap", which stores the information about
logical<->physical eraseblocks mappings. So now to get this
information just read the fastmap, instead of doing full scan. More
information here can be found in Richard's announcement in LKML
(Subject: UBI: Fastmap request for inclusion (v19)):
http://thread.gmane.org/gmane.linux.kernel/1364922/focus=1369109
One thing I want to explicitly say is that fastmap did not have large
enough linux-next exposure. It is partially my fault - I did not
respond quickly enough. I _really_ apologize for this. But it had
good testing and disabled by default, so I do not expect that we'll
break anything.
Fastmap is declared as experimental so far, and it is off by default.
We did declare that the on-flash format may be changed. The reason
for this is that no one used it in real production so far, so there is
a high risk that something is missing. Besides, we do not have
user-space tools supporting fastmap so far.
Nevertheless, I suggest we merge this feature. Many people want UBI's
scanning bottleneck to be fixed and merging fastmap now should
accelerate its production use. The plan is to make it bullet-prove,
somewhat clean-up, and make it the default for UBI. I do not know how
many kernel releases will it take.
Basically, I what I want to do for fastmap is something like Linus did
for btrfs few years ago."
* tag 'upstream-3.7-rc1-fastmap' of git://git.infradead.org/linux-ubi:
UBI: Wire-up fastmap
UBI: Add fastmap core
UBI: Add fastmap support to the WL sub-system
UBI: Add fastmap stuff to attach.c
UBI: Wire-up ->fm_sem
UBI: Add fastmap bits to build.c
UBI: Add self_check_eba()
UBI: Export next_sqnum()
UBI: Add fastmap stuff to ubi.h
UBI: Add fastmap on-flash data structures
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
Make fastmap known to Kconfig, UBI Makefile and MAINTAINERS.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
