The C inline keyword is not standardized, ACPI_INLINE allows this
to be configured on a per-compiler basis.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This function is not OS-dependent and has been replaced by
acpi_hw_derive_pci_id, which is now in the ACPICA core code. Local
implementations of acpi_os_derive_pci_id are no longer necessary and
are removed. ACPICA BZ 857.
http://www.acpica.org/bugzilla/show_bug.cgi?id=857
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds install/remove interfaces so that the host can dynamically
alter the global _OSI table. Also adds support for _OSI handlers.
Additional support: new debugger command (osi), and test support in
the acpiexec utility. Adds new file, utilities/utosi.c.
ACPICA bugzilla 836.
The Linux OSL _OSI code is also changed.
acpi_osi_setup can't call acpi_install/remove_interface because ACPICA
is not initialized yet at this early time.
So we just save the osi string in acpi_osi_setup and will handle it
later in a new function acpi_osi_setup_late.
http://www.acpica.org/bugzilla/show_bug.cgi?id=836
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com
Signed-off-by: Len Brown <len.brown@intel.com>
This reverts commit f23b9c7(http://git.moblin.org/cgit.cgi/acpica/commit/?id=f23b9c7)
The problem with this change was determined to be a problem with
the FreeBSD host OSL (OS services layer), not with this patch
itself. Therefore, re-introducing this change into the main ACPICA
code. See ACPICA bugzilla 863.
http://www.acpica.org/bugzilla/show_bug.cgi?id=863
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Prototype in acpiosxf.h had the output value pointer as a (u32 *).
Should be a (u64 *).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Section 4.7.3.1.1 (PM1 Status Registers) of version 4.0 of
the ACPI spec concerning PCIEXP_WAKE_STS points out in
in the final note field in table 4-11 that if this bit is
set to 1 and the system is put into a sleeping state then
the system will not automatically wake.
This bit gets set by hardware to indicate that the system
woke up due to a PCI Express wakeup event, so clear it during
acpi_hw_clear_acpi_status() calls to enable subsequent
resumes to work.
BugLink: http://bugs.launchpad.net/bugs/613381
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The current ACPI GPEs initialization code has a problem that it
enables some GPEs pointed to by device _PRW methods, generally
intended for signaling wakeup events (system or device wakeup).
These GPEs are then almost immediately disabled by the ACPI namespace
scanning code with the help of acpi_gpe_can_wake(), but it would be
better not to enable them at all until really necessary.
Modify the initialization of GPEs so that the ones that have
associated _Lxx or _Exx methods and are not pointed to by any _PRW
methods will be enabled after the namespace scan is complete.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Some minor improvements in error handling, but overall it was mostly dead
code.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce module parameter acpi.aml_debug_output.
With acpi.aml_debug_output set, we can get AML debug object output
(Store (AAA, Debug)), even with CONFIG_ACPI_DEBUG cleared.
Together with the runtime custom method mechanism,
we can debug AML code problems without rebuilding the kernel.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (27 commits)
ACPI / ACPICA: Simplify acpi_ev_initialize_gpe_block()
ACPI / ACPICA: Fail acpi_gpe_wakeup() if ACPI_GPE_CAN_WAKE is unset
ACPI / ACPICA: Do not execute _PRW methods during initialization
ACPI: Fix bogus GPE test in acpi_bus_set_run_wake_flags()
ACPICA: Update version to 20100702
ACPICA: Fix for Alias references within Package objects
ACPICA: Fix lint warning for 64-bit constant
ACPICA: Remove obsolete GPE function
ACPICA: Update debug output components
ACPICA: Add support for WDDT - Watchdog Descriptor Table
ACPICA: Drop acpi_set_gpe
ACPICA: Use low-level GPE enable during GPE block initialization
ACPI / EC: Do not use acpi_set_gpe
ACPI / EC: Drop suspend and resume routines
ACPICA: Remove wakeup GPE reference counting which is not used
ACPICA: Introduce acpi_gpe_wakeup()
ACPICA: Rename acpi_hw_gpe_register_bit
ACPICA: Update version to 20100528
ACPICA: Add signatures for undefined tables: ATKG, GSCI, IEIT
ACPICA: Optimization: Reduce the number of namespace walks
...
If a handler is installed for a GPE associated with an AML method and
such that it cannot wake up the system from sleep states, the GPE
remains enabled after the handler has been installed, although it
should be disabled in that case to avoid spurious execution of the
handler.
Fix this issue by making acpi_install_gpe_handler() disable GPEs
that were previously associated with AML methods and cannot wake up
the system from sleep states.
Analogously, make acpi_remove_gpe_handler() enable the GPEs that
are associated with AML methods after their handlers have been
removed and cannot wake up the system from sleep states. In addition
to that, fix a code ordering issue in acpi_remove_gpe_handler() that
renders the locking ineffective (ACPI_MTX_EVENTS is released
temporarily in the middle of the routine to wait for the completion
of events already in progress).
For this purpose introduce acpi_raw_disable_gpe() and
acpi_raw_enable_gpe() to be called with acpi_gbl_gpe_lock held
and rework acpi_disable_gpe() and acpi_enable_gpe(), respectively, to
use them. Also rework acpi_gpe_can_wake() to use
acpi_raw_disable_gpe() instead of calling acpi_disable_gpe() after
releasing the lock to avoid the possible theoretical race with
acpi_install_gpe_handler().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: "Moore, Robert" <robert.moore@intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Simplify the main loop in acpi_ev_initialize_gpe_block() by
rearranging code and removing the "enabled" label that is not
necessary any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make acpi_gpe_wakeup() return error code for GPEs whose
ACPI_GPE_CAN_WAKE flag is not set. This way acpi_gpe_wakeup() will
only wake for the GPEs reported by the host OS as "wakeup" ones with
the help of acpi_gpe_can_wake().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, during initialization ACPICA walks the entire ACPI
namespace in search of any device objects with assciated _PRW
methods. All of the _PRW methods found are executed in the process
to extract the GPE information returned by them, so that the GPEs in
question can be marked as "able to wakeup" (more precisely, the
ACPI_GPE_CAN_WAKE flag is set for them). The only purpose of this
exercise is to avoid enabling the CAN_WAKE GPEs automatically, even
if there are _Lxx/_Exx methods associated with them. However, it is
both costly and unnecessary, because the host OS has to execute the
_PRW methods anyway to check which devices can wake up the system
from sleep states. Moreover, it then uses full information
returned by _PRW, including the GPE information, so it can take care
of disabling the GPEs if necessary.
Remove the code that walks the namespace and executes _PRW from
ACPICA and modify comments to reflect that change. Make
acpi_bus_set_run_wake_flags() disable GPEs for wakeup devices
so that they don't cause spurious wakeup events to be signaled.
This not only reduces the complexity of the ACPICA initialization
code, but in some cases it should reduce the kernel boot time as
well.
Unfortunately, for this purpose we need a new ACPICA function,
acpi_gpe_can_wake(), to be called by the host OS in order to disable
the GPEs that can wake up the system and were previously enabled by
acpi_ev_initialize_gpe_block() or acpi_ev_update_gpes() (such a GPE
should be disabled only once, because the initialization code enables
it only once, but it may be pointed to by _PRW for multiple devices
and that's why the additional function is necessary).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a problem where a reference to an Alias within the
definition of a Package was not always resolved properly. Aliases
to objects like Processors, ThermalZones, etc. were resolved to the
actual object instead of a reference to the object as it should be.
Package objects are only allowed to contain integer, string,
buffer, package, and reference objects.
https://bugzilla.redhat.com/show_bug.cgi?id=608648
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
cast to u64.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove acpi_hw_write_gpe_enable_reg, it had been reduced down to a
single line of code, and called from only one place.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The acpi_set_gpe() function is a little awkward, because it doesn't
really work as advertised in the "disable" case. Namely, if a GPE
has been enabled with acpi_enable_gpe() and triggered a notification
to occur, and if acpi_set_gpe() is used to disable it before
acpi_ev_asynch_enable_gpe() runs, the GPE will be immediately enabled
by the latter as though the acpi_set_gpe() had no effect.
Thus, since it's been possible to make all of its callers use
alternative operations to disable or enable GPEs, acpi_set_gpe() can
be dropped.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The GPE block initialization code in acpi_ev_initialize_gpe_block()
uses acpi_set_gpe() to make sure that the GPEs with nonzero
runtime counter will remain enabled, but since it already has
a struct acpi_gpe_event_info object for each GPE, it might use
the low-level GPE enabling function, acpi_clear_and_enable_gpe(),
for this purpose.
To make that happen, move acpi_clear_and_enable_gpe() to
drivers/acpi/acpica/evgpe.c and rename it to acpi_ev_enable_gpe(),
modify the two existing users of it accordingly and modify
acpi_ev_initialize_gpe_block() to use it instead of acpi_set_gpe()
and to check its return value.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
After the previous patch that introduced acpi_gpe_wakeup() and
modified the ACPI suspend and wakeup code to use it, the third
argument of acpi_{enable|disable}_gpe() and the GPE wakeup
reference counter are not necessary any more. Remove them and
modify all of the users of acpi_{enable|disable}_gpe()
accordingly. Also drop GPE type constants that aren't used
any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses reference counters to avoid disabling GPEs too early in
case they have been enabled for many times. This is done separately
for runtime and for wakeup, but the wakeup GPE reference counter is
not really necessary, because GPEs are only enabled to wake up the
system at the hardware level by acpi_enter_sleep_state(). Thus it
only is necessary to set the corresponding bits in the wakeup enable
masks of these GPEs' registers right before the system enters a sleep
state. Moreover, the GPE wakeup enable bits can only be set when the
target sleep state of the system is known and they need to be cleared
immediately after wakeup regardless of how many wakeup devices are
associated with a given GPE.
On the basis of the above observations, introduce function
acpi_gpe_wakeup() to be used for setting or clearing the enable bit
corresponding to a given GPE in its enable register's enable_for_wake
mask. Modify the ACPI suspend and wakeup code the use
acpi_gpe_wakeup() instead of acpi_{enable|disable}_gpe() to set
and clear GPE enable bits in their registers' enable_for_wake masks
during system transitions to a sleep state and back to the working
state, respectively. [This will allow us to drop the third
argument of acpi_{enable|disable}_gpe() and simplify the GPE
handling code.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename acpi_hw_gpe_register_bit to acpi_hw_get_gpe_register_bit
in order to be same with ACPICA code base.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On control method exit, only walk the namespace if the method is
known to have created namespace objects outside of its local scope.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove obsolete AOPOBJ_SINGLE_DATUM. Add AOPOBJ_INVALID for
use if the host OS rejects the address of an operation region
(currently only used by Linux.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change enhances the performance of namespace searches and
walks by adding a backpointer to the parent in each namespace
node. On large namespaces, this change can improve overall ACPI
performance by up to 9X. Adding a pointer to each namespace node
increases the overall size of the internal namespace by about 5%,
since each namespace entry usually consists of both a namespace
node and an ACPI operand object.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Expand the various device initialization counters from 16-bit
to 32-bit. Allows for very large namespaces.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
With only a few exceptions, ACPICA does not use signed integers.
Therefore, %d is incorrect.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Expand the various initialization counters from 16-bit to 32-bit.
Allows for very large namespaces.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These objects are defined by "Windows Instrumentation", and are
not part of the ACPI spec. Adds compiler support and runtime
typechecking support in the ACPICA core. ACPICA BZ 860.
http://www.acpica.org/bugzilla/show_bug.cgi?id=860
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Because of package index values used for _BQC and _BCM.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Folklore suggested that such systems existed
in the pre-history of ACPI.
However, we removed the SCI_EN polling loop from
acpi_hw_set_mode() in b430acbd7c
because it delayed resume by 3 seconds on boxes
that refused to set SCI_EN.
Matthew removed the call to acpi_enable() from
the suspend resume path.
James found a modern system that still needs to be polled
upon boot.
So here we restore the workaround, except that we
put it in acpi_enable() rather than the low level
acpi_hw_set_mode().
https://bugzilla.kernel.org/show_bug.cgi?id=16271
Signed-off-by: Len Brown <len.brown@intel.com>
This feature is optional and is enabled if the BIOS requests any
Windows OSI strings. It can also be enabled by the host OS.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
To prevent accidental deep sleeps, limit the maximum time that
Sleep() will sleep. Configurable, default maximum is two seconds.
ACPICA bugzilla 854.
http://www.acpica.org/bugzilla/show_bug.cgi?id=854
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
While developing the GPE reference counting code we overlooked the
fact that acpi_ev_update_gpes() could have enabled GPEs before
acpi_ev_initialize_gpe_block() was called. As a result, some GPEs
are enabled twice during the initialization.
To fix this issue avoid calling acpi_enable_gpe() from
acpi_ev_initialize_gpe_block() for the GPEs that have nonzero
runtime reference counters.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_hw_write_gpe_enable_reg() to re-enable a GPE after
an event signaled by it has been handled. However, this function
writes the entire GPE enable mask to the GPE's enable register which
may not be correct. Namely, if one of the other GPEs in the same
register was previously enabled by acpi_enable_gpe() and subsequently
disabled using acpi_set_gpe(), acpi_hw_write_gpe_enable_reg() will
re-enable it along with the target GPE.
To fix this issue rework acpi_hw_write_gpe_enable_reg() so that it
calls acpi_hw_low_set_gpe() with a special action value,
ACPI_GPE_COND_ENABLE, that will make it only enable the GPE if the
corresponding bit in its register's enable_for_run mask is set.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_ev_enable_gpe() for enabling GPEs at the low level,
which is incorrect, because this function only enables the GPE if the
corresponding bit in its enable register's enable_for_run mask is set.
This causes acpi_set_gpe() to work incorrectly if used for enabling
GPEs that were not previously enabled with acpi_enable_gpe(). As a
result, among other things, wakeup-only GPEs are never enabled by
acpi_enable_wakeup_device(), so the devices that use them are unable
to wake up the system.
To fix this issue remove acpi_ev_enable_gpe() and its counterpart
acpi_ev_disable_gpe() and replace acpi_hw_low_disable_gpe() with
acpi_hw_low_set_gpe() that will be used instead to manipulate GPE
enable bits at the low level. Make the users of acpi_ev_enable_gpe()
and acpi_ev_disable_gpe() call acpi_hw_low_set_gpe() instead and
make sure that GPE enable masks are only updated by acpi_enable_gpe()
and acpi_disable_gpe() when GPE reference counters change from 0
to 1 and from 1 to 0, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In quite a few places ACPICA needs to compute a GPE enable mask with
only one bit, corresponding to a given GPE, set. Currently, that
computation is always open coded which leads to unnecessary code
duplication. Fix this by introducing a helper function for computing
one-bit GPE enable masks and using it where appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 0f849d2cc6 (ACPICA: Minimize
the differences between linux GPE code and ACPICA code base)
introduced a change attempting to disable a GPE before installing
a handler for it in acpi_install_gpe_handler() which was incorrect.
First, the GPE disabled by it is never enabled again (except during
resume) which leads to battery insert/remove events not being
reported on the Maxim Levitsky's machine. Second, the disabled
GPE is still reported as enabled by the sysfs interface that only
checks its enable register's enable_for_run mask.
Revert this change for now, because it causes more damage to happen
than the bug it was supposed to fix.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_hw_set_mode() double checks its effectiveness
by calling acpi_hw_get_mode() -- polling up to 3 seconds.
It would be more logical for its caller, acpi_enable()
acpi_enable() to do the double-checking. (lets assume
that acpi_disable() isn't interesting)
The ACPI specification is unclear on this point.
Some parts say that the BIOS sets SCI_EN and then returns to the OS,
but one part says "OSPM polls the SCI_EN bit until it is sampled SET".
The systems I have on hand do the former,
SCI_EN is observed to be set upon return from the BIOS.
So we move the check up out of acpi_hw_set_mode()
up into acpi_enable() where it makes logical sense.
Then we replace the 3-second polling loop
with a single check. If this check fails, we'll see:
"Hardware did not enter ACPI mode"
and the system will bail out of ACPI initialization
and likely fail to boot. If we see that in practice,
we can restore the polling, but put it into acpi_enable.
This patch is important if acpi_enable() is used in
the resume from S3 path. Many systems today are seen
coming back from S3 with SCI_EN off, and then failing
to set SCI_EN in response to acpi_enable(). Those systems
will take 3 seconds longer to resume due to this loop.
However, it is possible that we will not use acpi_enable()
in the S3 resume path, and bang SCI_EN directly, which
would make the loop harmless, as it would be invisible
to all systems except those that need it.
Signed-off-by: Len Brown <len.brown@intel.com>
Suspend has other meanings in ACPI context, name was misleading.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Original code did not handle the case where the object to be
copied was a namespace node.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Create two new files, evgpeinit.c and evgpeutil.c. Updated
unix and linux makefiles.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For all GPEs, including FADT-based and GPE Block Devices, execute
any _PRW methods in the new table, and process any _Lxx/_Exx GPE
methods in the new table. Any runtime GPE that is referred to
by an _Lxx/_Exx method in the new table is immediately enabled.
ACPICA BZ 833.
http://www.acpica.org/bugzilla/show_bug.cgi?id=833
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Original fields were not very descriptive and led to maintenance
problems. New fields should help to understand the existing code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We have ported Rafael's major GPE changes
(ACPI: Use GPE reference counting to support shared GPEs) into ACPICA code base.
But the port and Rafael's original patch have some differences, so we made
below patch to make linux GPE code consistent with ACPICA code base.
Most changes are about comments and coding styles.
Other noticeable changes are based on:
Rafael: Reduce code duplication related to GPE lookup
https://patchwork.kernel.org/patch/86237/
Rafael: Always use the same lock for GPE locking
https://patchwork.kernel.org/patch/90471/
A new field gpe_count in struct acpi_gpe_block_info to record the number
of individual GPEs in block.
Rename acpi_ev_save_method_info to acpi_ev_match_gpe_method.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some BIOS on Toshiba machines corrupt the DSDT, so add a new
boot option acpi=copy_dsdt to workaround it.
Add warning message to ask users to use this option if corrupt DSDT detected.
Also build a DMI blacklist to check it and automatically copy DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move initialization of DSDT pointer. Emit address of DSDT
in the dump of both table headers (good/bad DSDT).
Now handles the case where the root table can be reallocated,
which would invalidate the original pointer.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Optionally copy the entire DSDT to local memory (instead of
simply mapping it.) There are some BIOSs that corrupt or replace
the original DSDT, creating the need for this option. Default is
FALSE, do not copy the DSDT.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change adds support to detect a DSDT that has been corrupted
and/or replaced from outside the OS (by firmware). This is
typically catastrophic for the system, but has been seen on
some machines.
https://bugzilla.kernel.org/show_bug.cgi?id=14679
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The original implementation only supported reading from a DataTable
region. However, some machines have been seen that actually write
to the ACPI table contained in such a region. This change adds
support for writing to a DataTable region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When copying the root table to the new allocation, the length
used was incorrect. The new size was used instead of the current
table size, meaning too much data was copied.
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Also split some long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a problem with the AML Mutex handling function
acpi_ex_release_mutex where the function could fault under the very
rare condition when the interpreter has blocked, the interpreter
lock is released, the interpreter is then reentered via the
same thread, and attempts to acquire a mutex that was previously
acquired. FreeBSD report 140979.
http://www.freebsd.org/cgi/query-pr.cgi?pr=140979
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Always use 0x prefix for hex output, use %u for integer output
(all integers are unsigned.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will enable debug object output via a global variable,
acpi_gbl_enable_aml_debug_object. This will help with remote machine
debugging. Also, moved all debug object support code to a new
file, exdebug.c. Entire debug object module can now be
configured out of the ACPICA build if desired.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
access_bit_width field is u8 in ACPICA, thus 256 value written to it
becomes 0, causing divide by zero later.
Proper fix would be to remove access_bit_width at all, just because
we already have access_byte_width, which is access_bit_width / 8.
Limit access width to 64 bit for now.
https://bugzilla.kernel.org/show_bug.cgi?id=15749
fixes regression caused by the fix for:
https://bugzilla.kernel.org/show_bug.cgi?id=14667
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_ev_enable_gpe() should enable the GPE at the hardware level
regardless of the value of the GPE's runtime reference counter.
There are only two callers of acpi_ev_enable_gpe(), acpi_enable_gpe()
and acpi_set_gpe(). The first one checks the GPE's runtime
reference counter itself and only calls acpi_ev_enable_gpe() if it's
equal to one, and the other one is supposed to enable the GPE
unconditionally (if called with ACPI_GPE_ENABLE).
This change fixes the problem in acpi_enable_wakeup_device() where
the GPE will not be enabled for wakeup if it's runtime reference
counter is zero, which is a regression from 2.6.33.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-by: Robert Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPI: replace acpi_integer by u64
ACPICA: Update version to 20100121.
ACPICA: Remove unused uint32_struct type
ACPICA: Disassembler: Remove obsolete "Integer64" field in parse object
ACPICA: Remove obsolete ACPI_INTEGER (acpi_integer) type
ACPICA: Predefined name repair: fix NULL package elements
ACPICA: AcpiGetDevices: Eliminate unnecessary _STA calls
ACPICA: Update all ACPICA copyrights and signons to 2010
ACPICA: Update for new gcc-4 warning options
To fix a bug and address the reviewers' comments regarding the ACPI
GPE refcounting patch, do the following additional changes:
o Remove the second argument of acpi_ev_enable_gpe(),
'write_to_hardware', because it is not necessary any more.
o Add the "bad parameter" test against 'type' in
acpi_enable_gpe() and acpi_disable_gpe().
o Make acpi_enable_gpe() only check 'status' for runtime GPEs if
acpi_ev_enable_gpe() was actually called.
o Make acpi_disable_gpe() return 'status' returned by
acpi_ev_disable_gpe() and fix a bug where ACPI_GPE_TYPE_WAKE
and ACPI_GPE_TYPE_RUNTIME were exchanged by mistake.
o Add comments explaining why acpi_set_gpe() is used by the ACPI EC
driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently it only is possible to install one system notify handler
per namespace node, but this is not enough for PCI run-time power
management, because we need to install power management notifiers for
devices that already have hotplug notifiers installed. While in
principle this could be handled at the PCI level, that would be
suboptimal due to the way in which the ACPI-based PCI hotplug code is
designed.
For this reason, modify ACPICA so that it is possible to install more
than one system notify handler per namespace node. Namely, make
acpi_install_notify_handler(), acpi_remove_notify_handler() and
acpi_ev_notify_dispatch() use a list of system notify handler objects
associated with a namespace node.
Make acpi_remove_notify_handler() call acpi_os_wait_events_complete()
upfront to avoid a situation in which concurrent instance of
acpi_remove_notify_handler() removes the handler from under us while
we're waiting for the event queues to flush.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
ACPI GPEs may map to multiple devices. The current GPE interface
only provides a mechanism for enabling and disabling GPEs, making
it difficult to change the state of GPEs at runtime without extensive
cooperation between devices.
Add an API to allow devices to indicate whether or not they want
their device's GPE to be enabled for both runtime and wakeup events.
Remove the old GPE type handling entirely, which gets rid of various
quirks, like the implicit disabling with GPE type setting. This
requires a small amount of rework in order to ensure that non-wake
GPEs are enabled by default to preserve existing behaviour.
Based on patches from Matthew Garrett <mjg@redhat.com>.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
trivial, leftover from my NULL pointer dereference patch which got
'superseded' by commit fbc3be2
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
This field is no longer needed. The "Integer" field is 64 bit
and is sufficient.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This type was introduced as the code was migrated from ACPI 1.0
(with 32-bit AML integers) to ACPI 2.0 (with 64-bit integers). It
is now obsolete and this change removes it from the ACPICA code
base, replaced by u64. The original typedef has been retained
for now for compatibility with existing device driver code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
For the predefined methods that return fixed-length packages
(or subpackages), attempt repair for a NULL element. Create an
Integer of value 0, a NULL String, or a zero-length buffer as
appropriate.
http://www.acpica.org/bugzilla/show_bug.cgi?id=818
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In the case where a specific _HID is requested, do not run _STA
until a _HID match is found. This eliminates potentially dozens
of _STA calls during a search for a particular device/HID.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add 2010 copyright to all module headers and signons, including
the Linux header. This affects virtually every file in the ACPICA
core subsystem, iASL compiler, and all utilities.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added several new options for the gcc-4 generation, and updated
the source accordingly. This includes some code restructuring to
eliminate unreachable code, elimination of some gotos, elimination
of unused return values, and some additional casting.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change moves the check for a valid Thread ID structure up a
few lines to insure that the check is made before the structure
is actually used.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will automatically remove embedded and trailing NULL
package elements from returned package objects that are defined
to containe a variable number of sub-packages. The driver is then
presented with a package with no null elements to deal with.
ACPICA BZ 819.
http://www.acpica.org/bugzilla/show_bug.cgi?id=819
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change enables the execution of _REG methods that appear
in the same scope as the module-level code, in resonse to an
operation region declaration within the module-level code.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Only attempt the "complex" repairs (package sorting, buffer
expansion) if the previous "generic" validation and repair was
successful.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update comments for repair of _FDE and _GTM methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Repair mechanism was considered too wordy. Now, messages are only
unconditionally emitted if the return object cannot be repaired.
Existing messages for successful repairs were converted to
ACPI_DEBUG_PRINT messages for now. ACPICA BZ 827.
http://www.acpica.org/bugzilla/show_bug.cgi?id=827
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Move code specific to _FDE and _GTM into the generic repair code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem where mutex errors can occur when running a _REG
method that is in the same scope as a method-defined operation
region or an operation region under a module-level IF block.
This is rare, so the problem has not been seen before.
ACPICA BZ 826.
http://www.acpica.org/bugzilla/show_bug.cgi?id=826
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a few errors with the headers in utcopy.c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change enhances the automatic repairs/conversions for
predefined name return values to make Integers, Strings, and
Buffers fully interchangeable. Also, a Buffer can be converted
to a Package of Integers if necessary. The nsrepair.c module was
completely restructured.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change deletes the unnecessary acpi_ns_convert_entry_to_handle
interface and renames the acpi_ns_map_handle_to_node interface to
acpi_ns_validate_handle. ACPICA BZ 798.
http://www.acpica.org/bugzilla/show_bug.cgi?id=798
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The expected return value for both names is a Buffer of 5 DWORDS.
This repair fixes two possible problems (both seen in the field):
A package of integers is returned, or a buffer of BYTEs is returned.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
These messages were using the internal path for the message
instead of using the node name.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Both messages incorrectly used the internal Path string instead
of the node name.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
An object can be leaked for each block of executed module-level
code if the interpreter slack mode is enabled. The change deletes
any implicitly returned object in this case.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'acpica' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
ACPICA: Update version to 20091112.
ACPICA: Add additional module-level code support
ACPICA: Deploy new create integer interface where appropriate
ACPICA: New internal utility function to create Integer objects
ACPICA: Add repair for predefined methods that must return sorted lists
ACPICA: Fix possible fault if return Package objects contain NULL elements
ACPICA: Add post-order callback to acpi_walk_namespace
ACPICA: Change package length error message to an info message
ACPICA: Reduce severity of predefined repair messages, Warning to Info
ACPICA: Update version to 20091013
ACPICA: Fix possible memory leak for Scope ASL operator
ACPICA: Remove possibility of executing _REG methods twice
ACPICA: Add repair for bad _MAT buffers
ACPICA: Add repair for bad _BIF/_BIX packages
_BIF was returning buffer instead of a string since day 1 of ACPI.
Adding a warning for that is noble, but people don't like
when someone cries wolf in a production system.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=14379
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will execute module-level code that is not at the
root of the namespace (under a Device object, etc.).
ACPICA BZ 762.
http://www.acpica.org/bugzilla/show_bug.cgi?id=762
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Simplifies creation of simple integer objects.
ACPICA BZ 823.
http://www.acpica.org/bugzilla/show_bug.cgi?id=823
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_ut_create_integer_object. This function (when deployed) should
simplify some of the object creation code. ACPICA BZ 823.
http://www.acpica.org/bugzilla/show_bug.cgi?id=823
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This change will repair (by sorting) packages returned by _ALR,
_PSS, and _TSS. Drivers can now assume that the packages are
correctly sorted. Adds one new file, nsrepair2.c.
ACPICA BZ 784.
http://www.acpica.org/bugzilla/show_bug.cgi?id=784
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The existing interface only has a pre-order callback. This change
adds an additional parameter for a post-order callback which will
be more useful for bus scans. ACPICA BZ 779.
Also update the external calls to acpi_walk_namespace.
http://www.acpica.org/bugzilla/show_bug.cgi?id=779
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This message happens when the package element list is longer than
the declared length of the package. Changed to an info message
because this condition is not actually an error. It is caused by
the BIOS attempting to truncate the package on the fly by adjusting
the package element count at the start of the package definition.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Since the object was successfully repaired, a Warning is too
severe. Reduced to Info for now. We may eventually change these
messages to debug-only. ACPICA BZ 812.
http://www.acpica.org/bugzilla/show_bug.cgi?id=812
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Using Scope(\) to change the scope to the root could cause a
single object memory leak.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If a custom address space handler is installed by the host
before the "initialize operation regions" phase of the ACPICA
initialization, any _REG methods for that address space could
be executed twice. This change fixes the problem.
ACPICA BZ 427.
http://www.acpica.org/bugzilla/show_bug.cgi?id=427
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_MAT can inadvertently return an Integer instead of a Buffer
if the return value has been read from a Field whose width is
less than or equal to the global integer width (32 or 64 bits).
ACPICA BZ 810.
http://www.acpica.org/bugzilla/show_bug.cgi?id=810
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a repair for the "Oem Information" field which is often
mistakenly returned as an integer. It should always be a string.
ACPICA BZ 807.
http://www.acpica.org/bugzilla/show_bug.cgi?id=807
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Ensure that memory mappings created for operation regions
do not cross page boundaries. Crossing a page boundary
while mapping regions can cause warnings if the pages have different attributes.
Such regions are probably BIOS bugs, and this is the workaround.
http://bugzilla.kernel.org/show_bug.cgi?id=14445
[Kernel summit hacking hour]
Signed-off-by: Bob Moore <robert.moore@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alok N Kataria <akataria@vmware.com>
Cc: "Tan Wei Chong" <wei.chong.tan@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Bob Moore <robert.moore@intel.com>
LKML-Reference: <1253137123-18047-2-git-send-email-felipe.contreras@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-txt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, intel_txt: clean up the impact on generic code, unbreak non-x86
x86, intel_txt: Handle ACPI_SLEEP without X86_TRAMPOLINE
x86, intel_txt: Fix typos in Kconfig help
x86, intel_txt: Factor out the code for S3 setup
x86, intel_txt: tboot.c needs <asm/fixmap.h>
intel_txt: Force IOMMU on for Intel TXT launch
x86, intel_txt: Intel TXT Sx shutdown support
x86, intel_txt: Intel TXT reboot/halt shutdown support
x86, intel_txt: Intel TXT boot support
Add support for execution of an _INI method at the namespace root.
Although not defined in the ACPI specification, this support was
added to Windows around the Vista timeframe. It is added here
for Windows compatibility.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added strings for Windows server 2008, Windows Vista SP1,
Windows 7, and Windows server 2008 R2.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a possible memory leak in the interpreter for package
objects if the package initializer list is longer than the
defined size of the package. This apparently can only happen
if the BIOS changes the package size on the fly (seen in a _PSS
object), as both iASL and the other compiler do not allow this.
The interpreter will truncate the package to the defined size
(and issue an error message), but can leave the extra objects
undeleted if they have been pre-created during the argument
processing (such is the case if the package consists of a number
of sub-packages as in the _PSS.) ACPICA BZ 805.
http://www.acpica.org/bugzilla/show_bug.cgi?id=805
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
We silently ignore this construct for Windows compatibility
ACPICA BZ 785.
http://www.acpica.org/bugzilla/show_bug.cgi?id=785
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
_DSM can return any type of object, so validation on the return
type cannot be performed. ACPICA BZ 802.
http://www.acpica.org/bugzilla/show_bug.cgi?id=802
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Conflicts:
arch/x86/kernel/reboot.c
security/Kconfig
Merge reason: resolve the conflicts, bump up from rc3 to rc8.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move tboot.h from asm to linux to fix the build errors of intel_txt
patch on non-X86 platforms. Remove the tboot code from generic code
init/main.c and kernel/cpu.c.
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Allow writes to reserved ports. This change may eventually be
driven down in to acpi_write and acpi_read.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add limited support for executable AML code that exists outside
of any control method. This type of code has been illegal since
ACPI 2.0. The code must exist in an If/Else/While block. All AML
tables are supported, including tables that are dynamically loaded.
ACPICA BZ 762.
http://acpica.org/bugzilla/show_bug.cgi?id=762
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added 31 new names for ACPI 4.0.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem with the mechanism that prevents problems if the
acpi_terminate interface is inadvertently called more than once
before the ACPICA code is re-initialized. ACPICA BZ 795.
http://acpica.org/bugzilla/show_bug.cgi?id=795
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added one new package type, a package that contains a revision number and
a variable number of sub-packages. Restructured the module to
put the sub-package list traversal in a separate function.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem where a predefined method is defined to return
a variable-length Package of sub-packages. If the length is one,
the BIOS code occasionally creates a simple single package with
no sub-packages. This code attempts to fix the problem by wrapping
a new package object around the existing package. ACPICA BZ 790.
http://acpica.org/bugzilla/show_bug.cgi?id=790
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
New file is nsrepair.c. This is in preparation for additional
errror correcting code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a compatibility issue when the same buffer or string is
stored to itself. This has been seen in the field. Previously,
ACPICA would zero out the buffer/string. Now, the operation is
treated as a NOP.
http://bugzilla.acpica.org/show_bug.cgi?id=803
Reported-by: Rezwanul Kabir <Rezwanul_Kabir@Dell.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
http://bugzilla.kernel.org/show_bug.cgi?id=13620
If the dynamic region is created and added to resource list over and over again,
it has the potential to be a memory leak by growing the list every time.
This patch fixes the memory leak, as below
1) add a new field "count" to struct acpi_res_list.
When inserting, if the region(addr, len) is already in the resource
list, we just increase "count", otherwise, the region is inserted
with count=1.
When deleting, the "count" is decreased, if it's decreased to 0,
the region is deleted from the resource list.
With "count", the region with same address and length can only be
inserted to the resource list once, so prevent potential memory leak.
2) add a new function acpi_os_invalidate_address, which is called when
region is deleted.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added parens around the acpica version/modulename/linenumber to
clearly differentiate this group from the rest of the message.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a problem where the code that attempts to repair/convert
an object of incorrect type is only executed on the first time the
predefined method is called. The mechanism that disables warnings
on subsequent calls was interfering with the repair mechanism.
ACPICA BZ 781.
http://acpica.org/bugzilla/show_bug.cgi?id=781
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Function acpi_tb_print_table_header. Some ACPI tables contain
non-printable characters in one of the string fields of the the
header - Signature, OemId, OemTableId, or CompilerId. Invalid
characters are replaced by '?'. ACPICA BZ 788.
http://acpica.org/bugzilla/show_bug.cgi?id=788
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Handler was never invoked. Now invoked if/when host node is deleted.
Data object was not automatically deleted when host node was deleted.
Interface to handler had an unused parameter, removed it.
ACPICA BZ 778.
http://acpica.org/bugzilla/show_bug.cgi?id=778
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Adds support for IPMI which is similar to SMBus and uses a bi-directional data buffer.
ACPICA BZ 773.
http://acpica.org/bugzilla/show_bug.cgi?id=773
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixed a possible leak when an attempt is made to repair a return
object. The only current repair is an automatic buffer to string
conversion.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Two duplicates in acdebug.h.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Needed by drivers for new ACPi tables. Internal versions of
these functions still use 32-bit max transfers, in order to
minimize disruption and stack use for the standard ACPI registers
(FADT-based).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some were defined twice, causes a warning with gcc
-Wredundant-decls.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes warnings with gcc -Wcast-qual flag.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Support for graceful handling of sleep states (S3/S4/S5) after an Intel(R) TXT launch.
Without this patch, attempting to place the system in one of the ACPI sleep
states (S3/S4/S5) will cause the TXT hardware to treat this as an attack and
will cause a system reset, with memory locked. Not only may the subsequent
memory scrub take some time, but the platform will be unable to enter the
requested power state.
This patch calls back into the tboot so that it may properly and securely clean
up system state and clear the secrets-in-memory flag, after which it will place
the system into the requested sleep state using ACPI information passed by the kernel.
arch/x86/kernel/smpboot.c | 2 ++
drivers/acpi/acpica/hwsleep.c | 3 +++
kernel/cpu.c | 7 ++++++-
3 files changed, 11 insertions(+), 1 deletion(-)
Signed-off-by: Joseph Cihula <joseph.cihula@intel.com>
Signed-off-by: Shane Wang <shane.wang@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Preserving this bit breaks some machines. Not preserving this bit
seems to work OK in all cases, even though this goes against the
ACPI spec.
http://bugzilla.kernel.org/show_bug.cgi?id=13289
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Prevents a possible fault when a dynamic operation region is
deleted. ACPICA BZ 507.
http://acpica.org/bugzilla/show_bug.cgi?id=507
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Was called twice in the same function with the same parameter.
Alex Chiang.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Changed address parameter to a simple offset. This removes the
need for the caller to access the region object to obtain the
physical address.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Replace memory mapping with region access calls. Now, all region
accesses go through the region handler as they should.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This interface enables the override or creation of a single
control method. Useful to repair a bug or install a missing method.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Mark the DdbHandle as invalid after the table it refers to is
unloaded. This is needed because the handle itself may not be
deleted after the table unload, depending on whether it has been
stored in a named object by the caller.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix a problem where the DdbHandle could be prematurely deleted,
possibly causing a fault.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Reduced parameter count and reduced code for this frequently
used function.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a possible fault when parsing an ill-formed _PRT package.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Was putting several extra spaces on the next line.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI 4.0 specification has been changed to make the SyncLevel
for mutex objects more useful. When releasing a mutex, the
synclevel of the mutex must now be the same as the current sync
level. This makes more sense. This change updates the code to
match the spec.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes a problem where if multiple mutexes of the same sync level
are acquired but then not released in strict opposite order, the
current sync level becomes confused and can cause errors.
ACPICA BZ 471.
http://acpica.org/bugzilla/show_bug.cgi?id=471
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The AML BreakPoint opcode will now cause a break into the AML
debugger if it is present/configured. This matches the expected
behavior per the ACPI specification. Previously, only a message
was output.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Some possible warnings with gcc 4+, especially with extended warnings
enabled
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com
Signed-off-by: Len Brown <len.brown@intel.com>
Unused variables/headers, casting, etc.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix dereference of possibly null pointer "Predefined" in the case
where the method is not one of the predefined methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Fix warnings caused by size_t and ACPI_SIZE changing to 64 bits.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Warnings can be generated for printf-like statements that output
the ACPI_THREAD_ID on 64-bit builds, since this type can expand
to 64-bits depending on how it is defined. Use the %p format
specifier to allow the output to automatically expand to 64 bits.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove two unused/obsolete variables.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When copying these internal objects, cannot simply copy the
underlying OS object. A new OS object must be created.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Mostly for acpiexec, one in the core subsystem.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Moved the module name and line number to the end of the message.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The BIOS bug workaround mistakenly got disabled
when we followed the ACPI specification more closely
by ignoring OS updates to that bit.
(The BIOS is supposed to update SCI_EN, not the OS)
http://bugzilla.kernel.org/show_bug.cgi?id=13289
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add acpi/acpica/*.c to the acpi.* modparam namespace
so that any modparams we stick into ACPICA do not
expose ACPICA filenames to users.
There are currently only two modparams in ACPICA,
just recently added for
http://bugzilla.kernel.org/show_bug.cgi?id=13041
With this change, they become
acpi.gts=1
acpi.bfs=1
rather than
hwsleep.gts=1
hwsleep.bfs=1
Signed-off-by: Len Brown <len.brown@intel.com>
acpi_rs_get_pci_routing_table_length is not performing sufficient
validation on the package returned from _PRT. It assumes a package of
packages and fails/faults if this is not the case.
We should validate each subpackage when extracted from the parent
package, and not accept objects of the wrong type, since that will just
cause the scanning to fail (likely with a kernel oops).
This can only happen with a serious BIOS bug, and is accompanied by a
warning something like this:
ACPI Warning (nspredef-0949): \_SB_.PCI0.PEG4._PRT: Return Package type mismatch at index 0 - found Integer, expected Package [20090320]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit fdbdc7fc79.
That temporary quick-fix is no longer necessary,
as the previous patch, a65131e942,
"I/O port protection: update for windows compatibility"
should handle this issue for all ports, including this one.
Signed-off-by: Len Brown <len.brown@intel.com>
For windows compatibility,
1) On a port protection violation, simply ignore the request and
do not return an exception (allow the control method to continue execution.)
2) If only part of the request overlaps a protected port,
read/write the individual ports that are not protected.
http://bugzilla.kernel.org/show_bug.cgi?id=13036
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Executing BIOS code paths not exercised by Windows
tends to get Linux into trouble.
However, if a system does benefit from _GTS or _BFS,
acpi.gts=1 an acpi.bfs=1 are now available to enable them.
http://bugzilla.kernel.org/show_bug.cgi?id=13041
Signed-off-by: Len Brown <len.brown@intel.com>
Sony laptops apparently write 4-bytes (rather than 1 byte)
to debug port 0x80, which spews error messages:
Denied AML access to port 0x00000080/4 (DMA1 0x0081-0x0083) [20090320]
http://bugzilla.kernel.org/show_bug.cgi?id=13036
Signed-off-by: Len Brown <len.brown@intel.com>
Asus boards have an ACPI interface for interacting with the hwmon (fan,
temperatures, voltages) subsystem; this driver exposes the relevant
information via the standard sysfs interface.
There are two different ACPI interfaces:
- an old one (based on RVLT/RFAN/RTMP)
- a new one (GGRP/GITM)
Both may be present but there a few cases (my board, sigh) where the
new interface is just an empty stub; the driver defaults to the old one
when both are present.
The old interface has received a considerable testing, but I'm still
awaiting confirmation from my tester that the new one is working as
expected (hence the debug code is still enabled).
Currently all the attributes are read-only, though a (partial) control
should be possible with a bit more work.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
For predefined method validation. Index value in warning message
could be off by one.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
If both the 32-bit and 64-bit addresses are non-null, use the
32-bit address. Provides Windows compatibility.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Use the 32-bit register addresses whenever they are non-zero. This
means that the 32-bit addresses are favored over the 64-bit
(GAS) addresses. The 64-bit addresses are only used if the 32-bit
addresses are zero. This change provides compatibility with all
versions of Windows. The worst case that this solves is when both
the 32-bit and 64-bit addresses are non-zero, but only the 32-bit
addresses are actually valid. This appears to happen in some
BIOSes because in this case, Windows uses the 32-bit addresses.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Microsoft website uses 0xCF8-0xD00. Should be 0xCF8-0xCFF (Two
32-bit registers.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
One entry in the protected port table eliminated. Added extra
comments to describe each table entry.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Removed unused code for dump of args and locals. General cleanup
and splitting of long lines.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Affects PM1 Control register only. When reading the register, zero
the write-only bits as per the ACPI spec. ACPICA BZ 443. Lin Ming.
http://www.acpica.org/bugzilla/show_bug.cgi?id=443
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This interface is no longer necessary. Requests should be validated
on a per-field basis, not on the entire operation region.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Protect certain I/O ports from reads/writes. Provides MS
compatibility. New module, hwvalid.c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As per the ACPI specification, preserve (read/modify/write) all
bits that are defined as either reserved or ignored (PM control
control registers only.)
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Ignored bits must be preserved according to the ACPI spec.
Usually this means a read/modify/write when writing to the
register. However, for status registers, writing a one means
clear the event. Writing a zero means preserve the event (do not
clear.) This behavior is clarified in the ACPI 4.0 spec, and the
ACPICA code now simply always writes a zero to the ignored bit.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added a reader/writer locking mechanism to allow multiple
concurrent namespace walks (readers), but a dynamic table unload
will have exclusive access to the namespace. This fixes a problem
where a table unload could delete the portion of the namespace that
is currently being examined by a walk. Adds a new file, utlock.c
that implements the reader/writer lock mechanism. ACPICA BZ 749.
http://www.acpica.org/bugzilla/show_bug.cgi?id=749
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Incorrect register length mismatch between the 32 and 64 bit
registers in some cases. Code was was checking the wrong pointer
for non-zero, should be looking at the address within the GAS
structure.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Split long lines, update comments.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add and deploy constants for the PM status/enable/control
registers.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cleanup table header output.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Update code for acpi_read_bit_register and acpi_write_bit_register.
Simplified code path, condensed duplicate code.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename acpi_get_register and acpi_set_register to clarify the
purpose of these functions. New names are acpi_read_bit_register
and acpi_write_bit_register.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
