This patch speeds up sbp2 a little bit --- but more importantly, it
brings the behavior of sbp2 and fw-sbp2 closer to each other. Like
fw-sbp2, sbp2 now does not limit the size of single transfers to 255
sectors anymore, unless told so by a blacklist flag or by module load
parameters.
Only very old bridge chips have been known to need the 255 sectors
limit, and we have got one such chip in our hardwired blacklist. There
certainly is a danger that more bridges need that limit; but I prefer to
have this issue present in both fw-sbp2 and sbp2 rather than just one of
them.
An OXUF922 with 400GB 7200RPM disk on an S400 controller is sped up by
this patch from 22.9 to 23.5 MB/s according to hdparm. The same effect
could be achieved before by setting a higher max_sectors module
parameter. On buses which use 1394b beta mode, sbp2 and fw-sbp2 will
now achieve virtually the same bandwidth. Fw-sbp2 only remains faster
on 1394a buses due to fw-core's gap count optimization.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Replace sg->length by sg_dma_len(sg). Rename a variable for shorter
line lengths and eliminate some superfluous local variables.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes. I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.
The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev. (basically all inquiries it
issues can now be directly mapped).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
sbp2_host_reset and sbp2_handle_status_write are not serialized against
sbp2_alloc_device and sbp2_remove_device.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Bug found by Olaf Hering <olh@suse.de>:
sbp2util_remove_command_orb_pool requires a valid lu->hi pointer.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Revert commit 0555659d63 from 2.6.22-rc1.
The dma_set_mask call somehow failed on a PowerMac G5, PPC64:
http://lkml.org/lkml/2007/8/1/344
Should there ever occur a DMA mapping beyond the physical DMA range, a
proper SBP-2 firmware will report transport errors. So let's leave it
at that.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Olaf Hering <olh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
This is upwards compatible, except that integer values other than 0 or 1
are no longer accepted. But values like "Y", "N", "no", "nnoooh!" work
now.
Also, improve a comment on the serialize_io parameter and make the
ORB_SET_EXCLUSIVE macro ultra-safe.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
With "modprobe sbp2 long_ieee1394_id=y", the format of
/sys/bus/scsi/devices/*:*:*:*/ieee1394_id is changed from e.g.
0001041010004beb:0:0 to 0001041010004beb:00042c:0000.
The longer format fully conforms to object identifier sizes as per
SAM(-2...4) and reflects what the SAM target port identifier is meant to
contain: A Discovery ID allegedly specified by ISO/IEC 13213:1994 ---
however there is no such thing; the authors of SAM probably meant
Directory ID). Especially target nodes with multiple dynamically added
targets may use Directory IDs to persistently identify target ports.
The new format is independent of implementation details of nodemgr.
Thus the same ieee1394_id attribute format can be implemented in the new
firewire stack.
The ieee1394_id is typically used to create persistently named links in
/dev/disk/by-id.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Conflicts:
drivers/scsi/jazz_esp.c
Same changes made by both SCSI and SPARC trees: problem with UTF-8
conversion in the copyright.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
drivers/ieee1394/sbp2.c: In function 'sbp2util_access_timeout':
drivers/ieee1394/sbp2.c:399: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/ieee1394/sbp2.c:399: error: (Each undeclared identifier is reported only once
drivers/ieee1394/sbp2.c:399: error: for each function it appears in.)
drivers/ieee1394/sbp2.c:399: warning: implicit declaration of function 'signal_pending'
drivers/ieee1394/sbp2.c:399: warning: implicit declaration of function 'schedule_timeout'
drivers/ieee1394/sbp2.c: In function 'sbp2_prep_command_orb_sg':
drivers/ieee1394/sbp2.c:1438: warning: implicit declaration of function 'page_address'
drivers/ieee1394/sbp2.c:1438: warning: passing argument 2 of 'dma_map_single' makes pointer from integer without a cast
drivers/ieee1394/sbp2.c: In function 'sbp2_handle_status_write':
drivers/ieee1394/sbp2.c:1842: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
Possibly due to changes in -mm, but this file should explicitly include the
headers for the stuff it uses.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (brought into alphabetic order)
When the command ORB pool is created, the ORB list won't be accessed
concurrently. Therefore we don't have to take the spinlock there.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Unlike the name suggests, "cmd->scatter_gather_element" holds only the
s/g table, not the actual s/g elements. Since the table is only read
but never written by the device, DMA_BIDIRECTIONAL can be replaced by
DMA_TO_DEVICE which may be cheaper on some architectures.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In order to use OHCI-1394 physical DMA, all s/g elements, s/g tables,
ORBs, and response buffers have to reside within the first 4 GB of the
FireWire controller's physical address space. Set the correct mask for
DMA mappings.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The old setting is copy & waste from usb-storage and doesn't apply to
sbp2. There is only 4-byte alignment required for everything, except
for S/G table elements which have to be 8-byte aligned according to the
SBP-2 spec. (They happen to be ____cacheline_aligned in our
implementation. Whether that's good is another question.)
We now simply don't tune block queue alignment at all. The default
alignment would surely never become anything else than a multiple of 4,
else tons of calls to blk_queue_dma_alignment would have to be added
everywhere in drivers/...
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Since commit 98e238cd42 in Linux 2.6.19,
"ieee1394: sbp2: don't prefer MODE SENSE 10", some FireWire DVD-ROMs and
DVD-RWs were mistaken as CD-ROM because sr_mod now sent MODE SENSE 6.
The MMC command set includes only MODE SENSE 10.
http://bugzilla.kernel.org/show_bug.cgi?id=7800
This fix lets sbp2 switch scsi_device.use_10_for_rw on for MMC LUs.
This should rather be done in the command set driver sr_mod, not in the
sbp2 transport driver, and an according patch will follow for a next
Linux release.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Need to use a PCI device, not a FireWire host device. Problem found by
Andreas Schwab, mistake pointed out by Benjamin Herrenschmidt.
http://ozlabs.org/pipermail/linuxppc-dev/2006-December/029595.html
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Andreas Schwab <schwab@suse.de>
Delete some incorrect code, left over from the initial driver submission
in March 2001.
SBP-2 targets should provide sense data via the SBP-2 status block
(autosense). We have to pass the REQUEST_SENSE command through to
targets which don't implement autosense, if there are any, and to
accomodate application clients which use this command.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch consolidates some bookkeeping for driver registering. It
closely models what pci_register_driver() does. The main addition is
that the owner of the driver is set, so we get a proper symlink
for /sys/bus/ieee1394/driver/*/module.
Also moves setting of name and bus type into nodemgr. Because of this,
we can remove the EXPORT_SYMBOL for ieee1394_bus_type, since it's now
only used in ieee1394.ko.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
"struct scsi_id_instance_data" represents a logical unit.
Rename it to "struct sbp2_lu", and "scsi_id" to "lu".
Rename some other variables too.
Wrap almost all lines after at most 80 columns.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Prepend sbp2*_ to anything globally defined in sbp2.c except for some
macros. Strip sbp2_ from names of struct members.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This work is not delayed.
Also bring the code format in a state which reduces my work to merge
pending sbp2 patchs.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Replace some calls to SBP2_ERR and SBP2_WARN by SBP2_INFO.
Remove logging macros SBP2_NOTICE and SBP2_WARN.
Remove direct usage of HPSB_ logging macros.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The same case is handled further below in sbp2scsi_complete_command.
Note, the second version behaves slightly different but looks
preferable. It's an extremely unlikely case by the way.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove unnecessary function prototypes.
Remove variable names from function prototypes.
Move declarations from sbp2.h to sbp2.c.
Move definitions of driver templates together near the top of sbp2.c.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The queue depth can be read from /sys/bus/scsi/devices/*/queue_depth,
so don't log it. And the hint about speed improvements is misleading,
at least under current kernels. If serialization is switched off, read
performance is typically increased by less than 10%. (I did not test
write performance recently.) On the other hand, serialize_io=0 is not
yet safe due to some implementation issues that are not trivial to fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Put the target's fetch agent into reset state before the underlying ORB
DMA is unmapped and the ->done handler is called. It is highly unlikely
but the target could access that ORB right before sbp2 sends the reset
request.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This is a follow-up to patch "ieee1394: sbp2: enable auto spin-up for
Maxtor disks". When I 'ejected' an OXUF922 based HDD from a Mac OS X
box, it was spun down by the Mac and did not spin up by itself when
attached to a Linux box right after that. The first SCSI command that
required the bridge to access the drive ended in
sda:<6>sd 18:0:0:0: Device not ready: <6>: Current: sense key: Not Ready
Additional sense: Logical unit not ready, initializing cmd. required
Therefore the flag which instructs scsi_mod to send START STOP UNIT with
START=1 ("make medium ready") after such a condition is now enabled
unconditionally for all FireWire storage devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In the old days, sbp2 used to coerce all MODE SENSE commands into the
10 bytes version. When all command set conversions were removed from
sbp2 several months ago, sdev->use_10_for_ms = 1 was added. Meaning,
higher SCSI layers preferred the 10 bytes version but would try the 6
bytes version if the former failed.
Recently, a problem with the 10 bytes version was discovered. An Initio
INIC-1530 firmware accepted the 10 bytes version but replied with bogus
data, showing the HDD incorrectly as write-protected. Since RBC
actually mandates MODE SENSE (6), I checked which version was sent by
Windows XP and Mac OS X 10.3 to an SBP-2 target hosted by Linux --- it
was the 6 bytes version. (Exception: OS X sent the 10 bytes version to
an MMC target. RBC and SBC got MODE SENSE (6).)
Therefore, drop the use_10_for_ms flag from sbp2. Now the upper layers
will try MODE SENSE (6) before MODE SENSE (10) on all SBP-2 devices.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Scsi_remove_device() may go into uninterruptible sleep if blocked.
Therefore sbp2_remove() unblocks the Scsi_Host before the device is
requested to be removed. But there could be another 1394 bus reset
after that which would block the host again. The 1394 subsystem won't
call sbp2_update() concurrently to sbp2_remove(), which is why there is
no chance for sbp2_remove() to be unblocked by sbp2_update().
The fix is to tell sbp2's bus reset handler when a device is to be shut
down so that it skips scsi_block_requests() on that host. As before,
any new commands after a reset without reconnect will be failed quickly
by sbp2scsi_queuecommand().
In the long term, means to go without scsi_block_requests() should be
found.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove unused includes. Add missing includes, i.e. explicitly include
all used headers. Sort includes alphabetically. Replace one call to
signal_pending(current) to avoid to include headers just for this line.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
