ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop. The
intent was to set the zero bit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver attempts to use two TX rings but lacks proper support :
1) IRQ handler only takes care of TX completion on first TX ring
2) the stop/start logic uses the legacy functions (for non multiqueue
drivers)
This means all packets witk skb mark set to 1 are sent through high
queue but are never cleaned and queue eventualy fills and block the
device, triggering the infamous "NETDEV WATCHDOG" message.
Lets use a single TX ring to fix the problem, this driver is not a real
multiqueue one yet.
Minimal fix for stable kernels.
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set addr_assign_type correctly to NET_ADDR_RANDOM in case
a random MAC address was generated and assigned to the netdevice.
Fix error handling in atl1c_probe(). If atl1c_read_mac_addr()
couldn't get the hw mac address, and a random mac address get
set return the error code. Don't go to err_eeprom in
atl1c_probe(), use the generated MAC address in this case.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: use bitops
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per discussion with Ben Hutchings and David Miller, go through and
remove assignments of "N/A" to fw_version in various drivers'
.get_drvinfo routines. While there clean-up some use of bare
constants and such.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Cc: Jie Yang <jie.yang@atheros.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Atheros drivers into drivers/net/ethernet/atheros/ and
make the necessary Kconfig and Makefile changes.
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: Jie Yang <jie.yang@atheros.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
