Commit graph

86 commits

Author SHA1 Message Date
Tejun Heo
6a6b97d360 libata: improve phantom device detection
Currently libata uses four methods to detect device presence.

1. PHY status if available.
2. TF register R/W test (only promotes presence, never demotes)
3. device signature after reset
4. IDENTIFY failure detection in SFF state machine

Combination of the above works well in most cases but recently there
have been a few reports where a phantom device causes unnecessary
delay during probe.  In both cases, PHY status wasn't available.  In
one case, it passed #2 and #3 and failed IDENTIFY with ATA_ERR which
didn't qualify as #4.  The other failed #2 but as it passed #3 and #4,
it still caused failure.

In both cases, phantom device reported diagnostic failure, so these
cases can be safely worked around by considering any !ATA_DRQ IDENTIFY
failure as NODEV_HINT if diagnostic failure is set.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-11-14 18:51:57 -05:00
Tejun Heo
570106df6b libata-sff: fix ata_sff_post_internal_cmd()
ata_sff_post_internal_cmd() needs to grab port lock before calling
ata_bmdma_stop() and also need to clear hsm_task_state.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-10-22 20:40:15 -04:00
Tejun Heo
9c2676b61a libata-sff: kill spurious WARN_ON() in ata_hsm_move()
On HSM_ST_ERR, ata_hsm_move() triggers WARN_ON() if AC_ERR_DEV or
AC_ERR_HSM is not set.  PHY events may trigger HSM_ST_ERR with other
error codes and, with or without it, there just isn't much reason to
do WARN_ON() on it.  Even if error code is not set there, core EH
logic won't have any problem dealing with the error condition.

OSDL bz#11065 reports this problem.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-08 12:15:38 -04:00
Tejun Heo
341c2c958e libata: consistently use msecs for time durations
libata has been using mix of jiffies and msecs for time druations.
This is getting confusing.  As writing sub HZ values in jiffies is
PITA and msecs_to_jiffies() can't be used as initializer, unify unit
for all time durations to msecs.  So, durations are in msecs and
deadlines are in jiffies.  ata_deadline() is added to compute deadline
from a start time and duration in msecs.

While at it, drop now superflous _msec suffix from arguments and
rename @timeout to @deadline if it represents a fixed point in time
rather than duration.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-14 15:59:32 -04:00
Tejun Heo
a836d3e882 libata-sff: improve HSM violation reporting
Improve SFF HSM violation reporting such that each HSM violation can
be distinguished using ehi_desc.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-04 09:06:02 -04:00
Hugh Dickins
6311c90a9e libata: fix G5 SATA broken on -rc5
Fix G5 SATA irq 18: nobody cared, reported on -rc5 by Olaf Hering:
fixlet to a57c1bade5 libata-sff:
Fix oops reported in kerneloops.org for pnp devices with no ctl

Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Tested-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-06-05 08:36:37 -07:00
Alan Cox
a57c1bade5 libata-sff: Fix oops reported in kerneloops.org for pnp devices with no ctl
- Make ata_sff_altstatus private so nobody uses it by mistake
- Drop the 400nS delay from it

Add

ata_sff_irq_status	-	encapsulates the IRQ check logic

This function keeps the existing behaviour for altstatus using devices. I
actually suspect the logic was wrong before the changes but -rc isn't the
time to play with that

ata_sff_sync		-	ensure writes hit the device

Really we want an io* operation for 'is posted' eg ioisposted(ioaddr) so
that we can fix the nasty delay this causes on most systems.

- ata_sff_pause		-	400nS delay

Ensure the command hit the device and delay 400nS

- ata_sff_dma_pause

Ensure the I/O hit the device and enforce an HDMA1:0 transition delay.
Requires altstatus register exists, BUG if not so we don't risk
corruption in MWDMA modes. (UDMA the checksum will save your backside in
theory)

The only other complication then is devices with their own handlers.
rb532 can use dma_pause but scc needs to access its own altstatus
register for internal errata workarounds so directly call the drivers own
altstatus function.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-04 06:40:41 -04:00
Tejun Heo
78ab88f04f libata: improve post-reset device ready test
Some controllers (jmb and inic162x) use 0x77 and 0x7f to indicate that
the device isn't ready yet.  It looks like they use 0xff if device
presence is detected but connection isn't established.  0x77 or 0x7f
after connection is established and use the value from signature FIS
after receiving it.

This patch implements ata_check_ready(), which takes TF status value
and determines whether the port is ready or not considering the above
and other conditions, and use it in @check_ready() functions.  This is
safe as both 0x77 and 0x7f aren't valid ready status value even though
they have BSY bit cleared.

This fixes hot plug detection failures which can be triggered with
certain drives if they aren't already spun up when the data connector
is hot plugged.

Tested on sil, sil24, ahci (jmb/ich), piix and inic162x combined with
eight drives from all major vendors.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-05-06 11:32:02 -04:00
Tejun Heo
411cb3869a libata: make WARN_ON conditions in ata_sff_hsm_move() more strict
WARN_ON()'s in ata_hsm_move() was too liberal and got triggerred when
it shouldn't (e.g. hotplug events at the right moment).  As the HSM
only deals with device errors and state machine violations, make it
check only against them.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-25 00:45:09 -04:00
Tejun Heo
45db2f6c95 libata: move link onlineness check out of softreset methods
Currently, SATA softresets should do link onlineness check before
actually performing SRST protocol but it doesn't really belong to
softreset.

This patch moves onlineness check in softreset to ata_eh_reset() and
ata_eh_followup_srst_needed() to clean up code and help future sata_mv
changes which need clear separation between SCR and TF accesses.

sata_fsl is peculiar in that its softreset really isn't softreset but
combination of hardreset and softreset.  This patch adds dummy private
->prereset to keep the current behavior but the driver really should
implement separate hard and soft resets and return -EAGAIN from
hardreset if it should be follwed by softreset.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-04-17 15:44:25 -04:00
Tejun Heo
4c9bf4e799 libata: replace tf_read with qc_fill_rtf for non-SFF drivers
Now that all SFF stuff is separated out of core layer, core layer
doesn't call ops->tf_read directly.  It gets called only via
ops->qc_fill_rtf() for non-SFF drivers.  This patch directly
implements private ops->qc_fill_rtf() for non-SFF controllers and kill
ops->tf_read().

This is much cleaner for non-SFF controllers as some of them have to
cache SFF register values in private data structure and report the
cached values via ops->tf_read().  Also, ops->tf_read() gets nasty for
controllers which don't have clear notion of TF registers when
operation is not in progress.

As this change makes default ops->qc_fill_rtf unnecessary, move
ata_sff_qc_fill_rtf() form ata_base_port_ops to ata_sff_port_ops where
it belongs.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
22183bf569 libata: add qc_fill_rtf port operation
On command completion, ata_qc_complete() directly called ops->tf_read
to fill qc->result_tf.  This patch adds ops->qc_fill_rtf to replace
hardcoded ops->tf_read usage.

ata_sff_qc_fill_rtf() which uses ops->tf_read to fill result_tf is
implemented and set in ata_base_port_ops and other ops tables which
don't inherit from ata_base_port_ops, so this patch doesn't introduce
any behavior change.

ops->qc_fill_rtf() is similar to ops->sff_tf_read() but can only be
called when a command finishes.  As some non-SFF controllers don't
have TF registers defined unless they're associated with in-flight
commands, this limited operation makes life easier for those drivers
and help lifting SFF assumptions from libata core layer.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
305d2a1ab1 libata: unify mechanism to request follow-up SRST
Previously, there were two ways to trigger follow-up SRST from
hardreset method - returning -EAGAIN and leaving all device classes
unmodified.  Drivers never used the latter mechanism and the only use
case for the former was when hardreset couldn't classify.

Drop the latter mechanism and let -EAGAIN mean "perform follow-up SRST
if classification is required".  This change removes unnecessary
follow-up SRSTs and simplifies reset implementations.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
57c9efdfb3 libata: implement and use sata_std_hardreset()
Implement sata_std_hardreset(), which simply wraps around
sata_link_hardreset().  sata_std_hardreset() becomes new standard
hardreset method for sata_port_ops and sata_sff_hardreset() moves from
ata_base_port_ops to ata_sff_port_ops, which is where it really
belongs.

ata_is_builtin_hardreset() is added so that both
ata_std_error_handler() and ata_sff_error_handler() skip both builtin
hardresets if SCR isn't accessible.

piix_sidpr_hardreset() in ata_piix.c is identical to
sata_std_hardreset() in functionality and got replaced with the
standard function.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:23 -04:00
Tejun Heo
9dadd45b24 libata: move generic hardreset code from sata_sff_hardreset() to sata_link_hardreset()
sata_sff_hardreset() contains link readiness wait logic which isn't
SFF specific.  Move that part into sata_link_hardreset(), which now
takes two more parameters - @online and @check_ready.  Both are
optional.  The former is out parameter for link onlineness after
reset.  The latter is used to wait for link readiness after hardreset.

Users of sata_link_hardreset() is updated to use new funtionality and
ahci_hardreset() is updated to use sata_link_hardreset() instead of
sata_sff_hardreset().  This doesn't really cause any behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
aa2731ad9a libata: separate out ata_wait_ready() and implement ata_wait_after_reset()
Factor out waiting logic (which is common to all ATA controllers) from
ata_sff_wait_ready() into ata_wait_ready().  ata_wait_ready() takes
@check_ready function pointer and uses it to poll for readiness.  This
allows non-SFF controllers to use ata_wait_ready() to wait for link
readiness.

This patch also implements ata_wait_after_reset() - generic version of
ata_sff_wait_after_reset() - using ata_wait_ready().

ata_sff_wait_ready() is reimplemented using ata_wait_ready() and
ata_sff_check_ready().  Functionality remains the same.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
705e76beb9 libata: restructure SFF post-reset readiness waits
Previously, post-softreset readiness is waited as follows.

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. ata_bus_softreset() finishes with -ENODEV if status is still 0xff.
   If not, continue to #3.

3. ata_bus_post_reset() waits readiness of dev0 and/or dev1 depending
   on devmask using ata_sff_wait_ready().

And for post-hardreset readiness,

1. ata_sff_wait_after_reset() waits for 150ms and then for
   ATA_TMOUT_FF_WAIT if status is 0xff and other conditions meet.

2. sata_sff_hardreset waits for device readiness using
   ata_sff_wait_ready().

This patch merges and unifies post-reset readiness waits into
ata_sff_wait_ready() and ata_sff_wait_after_reset().

ATA_TMOUT_FF_WAIT handling is merged into ata_sff_wait_ready().  If TF
status is 0xff, link status is unknown and the port is SATA, it will
continue polling till ATA_TMOUT_FF_WAIT.

ata_sff_wait_after_reset() is updated to perform the following steps.

1. waits for 150ms.

2. waits for dev0 readiness using ata_sff_wait_ready().  Note that
   this is done regardless of devmask, as ata_sff_wait_ready() handles
   0xff status correctly, this preserves the original behavior except
   that it may wait longer after softreset if link is online but
   status is 0xff.  This behavior change is very unlikely to cause any
   actual difference and is intended.  It brings softreset behavior to
   that of hardreset.

3. waits for dev1 readiness just the same way ata_bus_post_reset() did.

Now both soft and hard resets call ata_sff_wait_after_reset() after
reset to wait for readiness after resets.  As
ata_sff_wait_after_reset() contains calls to ->sff_dev_select(),
explicit call near the end of sata_sff_hardreset() is removed.

This change makes reset implementation simpler and more consistent.

While at it, make the magical 150ms wait post-reset wait duration a
constant and ata_sff_wait_ready() and ata_sff_wait_after_reset() take
@link instead of @ap.  This is to make them consistent with other
reset helpers and ease core changes.

pata_scc is updated accordingly.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
203c75b824 libata: separate out ata_std_postreset() from ata_sff_postreset()
Separate out generic ATA portion from ata_sff_postreset() into
ata_std_postreset() and implement ata_sff_postreset() using the std
version.

ata_base_port_ops now has ata_std_postreset() for its postreset and
ata_sff_port_ops overrides it to ata_sff_postreset().

This change affects pdc_adma, ahci, sata_fsl and sata_sil24.  pdc_adma
now specifies postreset to ata_sff_postreset() explicitly.  sata_fsl
and sata_sil24 now use ata_std_postreset() which makes no difference
to them.  ahci now calls ata_std_postreset() from its own postreset
method, which causes no behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
0aa1113d54 libata: separate out ata_std_prereset() from ata_sff_prereset()
Separate out generic ATA portion from ata_sff_prereset() into
ata_std_prereset() and implement ata_sff_prereset() using the std
version.  Waiting for device readiness is the only SFF specific part.

ata_base_port_ops now has ata_std_prereset() for its prereset and
ata_sff_port_ops overrides it to ata_sff_prereset().  This change can
affect pdc_adma, ahci, sata_fsl and sata_sil24.  pdc_adma implements
its own prereset using ata_sff_prereset() and the rest has hardreset
and thus are unaffected by this change.

This change reflects real world situation.  There is no generic way to
wait for device readiness for non-SFF controllers and some of them
don't have any mechanism for that.  Non-sff drivers which don't have
hardreset should wrap ata_std_prereset() and wait for device readiness
itself but there's no such driver now and isn't likely to be popular
in the future either.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
288623a06c libata: clean up port_ops->sff_irq_clear()
->sff_irq_clear() is called only from SFF interrupt handler, so there
is no reason to initialize it for non-SFF controllers.  Also,
ata_sff_irq_clear() can handle both BMDMA and non-BMDMA SFF
controllers.

This patch kills ata_noop_irq_clear() and removes it from base
port_ops and sets ->sff_irq_clear to ata_sff_irq_clear() in sff
port_ops instead of bmdma port_ops.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
5682ed33aa libata: rename SFF port ops
Add sff_ prefix to SFF specific port ops.

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames ops and doesn't introduce any
behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:22 -04:00
Tejun Heo
9363c3825e libata: rename SFF functions
SFF functions have confusing names.  Some have sff prefix, some have
bmdma, some std, some pci and some none.  Unify the naming by...

* SFF functions which are common to both BMDMA and non-BMDMA are
  prefixed with ata_sff_.

* SFF functions which are specific to BMDMA are prefixed with
  ata_bmdma_.

* SFF functions which are specific to PCI but apply to both BMDMA and
  non-BMDMA are prefixed with ata_pci_sff_.

* SFF functions which are specific to PCI and BMDMA are prefixed with
  ata_pci_bmdma_.

* Drop generic prefixes from LLD specific routines.  For example,
  bfin_std_dev_select -> bfin_dev_select.

The following renames are noteworthy.

  ata_qc_issue_prot() -> ata_sff_qc_issue()
  ata_pci_default_filter() -> ata_bmdma_mode_filter()
  ata_dev_try_classify() -> ata_sff_dev_classify()

This rename is in preparation of separating SFF support out of libata
core layer.  This patch strictly renames functions and doesn't
introduce any behavior difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:21 -04:00
Tejun Heo
ed82f96425 libata/pdc_adma: make SFF EH handle non-bmdma SFF drivers and standardize pdc_adma ops
pdc_adma has interface similar to SFF but has its own DMA interface.
It currently implements noop bmdma ops to avoid crashing
ata_bmdma_error_handler() which BTW actually is EH for SFF drivers.

This patch makes ata_bmdma_error_handler() dereference bmdma ops iff
bmdma_addr is initialized as done in ata_bmdma_post_internal_cmd.
This change allows pdc_adma to standardize ops and use SFF
error_handler and post_internal_cmd.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:20 -04:00
Tejun Heo
6fd3639011 libata: kill ata_chk_status()
ata_chk_status() just calls ops->check_status and it only adds
confusion with other status functions.  Kill it.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
071ce34d57 libata: move ata_pci_default_filter() out of CONFIG_PCI
ata_pci_default_filter() doesn't really have anything to do with PCI.
It's generally applicable to BMDMA controllers.  Move it out of
CONFIG_PCI.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
624d5c514e libata: reorganize SFF related stuff
* Move SFF related functions from libata-core.c to libata-sff.c.

  ata_[bmdma_]sff_port_ops, ata_devchk(), ata_dev_try_classify(),
  ata_std_dev_select(), ata_tf_to_host(), ata_busy_sleep(),
  ata_wait_after_reset(), ata_wait_ready(), ata_bus_post_reset(),
  ata_bus_softreset(), ata_bus_reset(), ata_std_softreset(),
  sata_std_hardreset(), ata_fill_sg(), ata_fill_sg_dumb(),
  ata_qc_prep(), ata_dump_qc_prep(), ata_data_xfer(),
  ata_data_xfer_noirq(), ata_pio_sector(), ata_pio_sectors(),
  atapi_send_cdb(), __atapi_pio_bytes(), atapi_pio_bytes(),
  ata_hsm_ok_in_wq(), ata_hsm_qc_complete(), ata_hsm_move(),
  ata_pio_task(), ata_qc_issue_prot(), ata_host_intr(),
  ata_interrupt(), ata_std_ports()

* Make ata_pio_queue_task() global as it's now called from
  libata-sff.c.

* Move SFF related stuff in include/linux/libata.h and
  drivers/ata/libata.h into one place.  While at it, move timing
  constants into the global enum definition and fortify comments a
  bit.

This patch strictly moves stuff around and as such doesn't cause any
functional difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
272f7884e8 libata: reorder functions in libata-sff.c
Reorder functions in drivers/ata/libata-sff.c such that functions
generally follow ops table order and init functions come last.  This
is in preparation of SFF cleanup.

This patch strictly moves stuff around and as such doesn't cause any
functional difference.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-04-17 15:44:18 -04:00
Tejun Heo
a1efdaba2d libata: make reset related methods proper port operations
Currently reset methods are not specified directly in the
ata_port_operations table.  If a LLD wants to use custom reset
methods, it should construct and use a error_handler which uses those
reset methods.  It's done this way for two reasons.

First, the ops table already contained too many methods and adding
four more of them would noticeably increase the amount of necessary
boilerplate code all over low level drivers.

Second, as ->error_handler uses those reset methods, it can get
confusing.  ie. By overriding ->error_handler, those reset ops can be
made useless making layering a bit hazy.

Now that ops table uses inheritance, the first problem doesn't exist
anymore.  The second isn't completely solved but is relieved by
providing default values - most drivers can just override what it has
implemented and don't have to concern itself about higher level
callbacks.  In fact, there currently is no driver which actually
modifies error handling behavior.  Drivers which override
->error_handler just wraps the standard error handler only to prepare
the controller for EH.  I don't think making ops layering strict has
any noticeable benefit.

This patch makes ->prereset, ->softreset, ->hardreset, ->postreset and
their PMP counterparts propoer ops.  Default ops are provided in the
base ops tables and drivers are converted to override individual reset
methods instead of creating custom error_handler.

* ata_std_error_handler() doesn't use sata_std_hardreset() if SCRs
  aren't accessible.  sata_promise doesn't need to use separate
  error_handlers for PATA and SATA anymore.

* softreset is broken for sata_inic162x and sata_sx4.  As libata now
  always prefers hardreset, this doesn't really matter but the ops are
  forced to NULL using ATA_OP_NULL for documentation purpose.

* pata_hpt374 needs to use different prereset for the first and second
  PCI functions.  This used to be done by branching from
  hpt374_error_handler().  The proper way to do this is to use
  separate ops and port_info tables for each function.  Converted.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:18 -04:00
Tejun Heo
887125e374 libata: stop overloading port_info->private_data
port_info->private_data is currently used for two purposes - to record
private data about the port_info or to specify host->private_data to
use when allocating ata_host.

This overloading is confusing and counter-intuitive in that
port_info->private_data becomes host->private_data instead of
port->private_data.  In addition, port_info and host don't correspond
to each other 1-to-1.  Currently, the first non-NULL
port_info->private_data is used.

This patch makes port_info->private_data just be what it is -
private_data for the port_info where LLD can jot down extra info.
libata no longer sets host->private_data to the first non-NULL
port_info->private_data, @host_priv argument is added to
ata_pci_init_one() instead.  LLDs which use ata_pci_init_one() can use
this argument to pass in pointer to host private data.  LLDs which
don't should use init-register model anyway and can initialize
host->private_data directly.

Adding @host_priv instead of using init-register model for LLDs which
use ata_pci_init_one() is suggested by Alan Cox.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
2008-04-17 15:44:17 -04:00
Tejun Heo
1bd5b715a3 libata: make ata_pci_init_one() not use ops->irq_handler and pi->sht
ata_pci_init_one() is the only function which uses ops->irq_handler
and pi->sht.  Other initialization functions take the same information
as arguments.  This causes confusion and duplicate unused entries in
structures.

Make ata_pci_init_one() take sht as an argument and use ata_interrupt
implicitly.  All current users use ata_interrupt and if different irq
handler is necessary open coding ata_pci_init_one() using
ata_prepare_sff_host() and ata_activate_sff_host can be done under ten
lines including error handling and driver which requires custom
interrupt handler is likely to require custom initialization anyway.

As ata_pci_init_one() was the last user of ops->irq_handler, this
patch also kills the field.

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:17 -04:00
Tejun Heo
358f9a77a6 libata: implement and use ata_noop_irq_clear()
->irq_clear() is used to clear IRQ bit of a SFF controller and isn't
useful for drivers which don't use libata SFF HSM implementation.
However, it's a required callback and many drivers implement their own
noop version as placeholder.  This patch implements ata_noop_irq_clear
and use it to replace those custom placeholders.

Also, SFF drivers which don't support BMDMA don't need to use
ata_bmdma_irq_clear().  It becomes noop if BMDMA address isn't
initialized.  Convert them to use ata_noop_irq_clear().

Signed-off-by: Tejun Heo <htejun@gmail.com>
2008-04-17 15:44:16 -04:00
Tejun Heo
f659f0e448 libata-sff: handle controllers w/o ctl register
SFF incorrectly assumed that ctl register is available for all
controllers while some old SFF controllers don't have ctl register.
Make SFF handle controllers w/o ctl register by conditionalizing ctl
register access and softreset method.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-03-10 20:50:36 -04:00
Tejun Heo
4e6b79fa61 libata: factor out ata_pci_activate_sff_host() from ata_pci_one()
Factor out ata_pci_activate_sff_host() from ata_pci_one().  This does
about the same thing as ata_host_activate() but needs to be separate
because SFF controllers use different and multiple IRQs in legacy
mode.

This will be used to make SFF LLD initialization more flexible.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:16 -05:00
Tejun Heo
35a10a80da libata: use dev_driver_string() instead of "libata" in libata-sff.c
libata-sff code used DRV_NAME which is hardcoded to "libata" when
requesting resources.  Use dev_driver_string() such that low level
driver names are used in resource listing.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:15 -05:00
Tejun Heo
0dc36888d4 libata: rename ATA_PROT_ATAPI_* to ATAPI_PROT_*
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and
ATA_PROT_ATAPI_* are inconsistent causing confusion.  Rename them to
ATAPI_PROT_* and make them consistent with ATA counterpart.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-01-23 05:24:14 -05:00
Alan Cox
76548eda8c libata-sff: tf_load
Jeff said he preferred that the SFF tf_load followed the spec and we
documented that anyone who needed different overrode it, rather than it
using the ->check_status methods. No driver relies on the current behaviour.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-23 05:24:09 -05:00
Alan Cox
277d72a374 libata-sff: PCI IRQ handling fix
It is legitimate (although annoying and silly) for a PCI IDE controller
not to be assigned an interrupt and to be polled. The libata-sff code
should therefore not try and request IRQ 0 in this case.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-10 16:52:51 -05:00
Jeff Garzik
2dcb407e61 [libata] checkpatch-inspired cleanups
Tackle the relatively sane complaints of checkpatch --file.

The vast majority is indentation and whitespace changes, the rest are

* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2007-10-23 20:59:42 -04:00
Robert P. J. Day
3a4fa0a25d Fix misspellings of "system", "controller", "interrupt" and "necessary".
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".

Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
2007-10-19 23:10:43 +02:00
Linus Torvalds
2af170dd24 Merge branch 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  [libata] kill ata_sg_is_last()
  Update libata driver for bf548 atapi controller against the 2.6.24 tree.
  libata-sff: Correct use of check_status()
  drivers/ata: add support to Freescale 3.0Gbps SATA Controller
  pata_acpi: fix build breakage if !CONFIG_PM
2007-10-18 15:08:35 -07:00
Stephen Hemminger
c80544dc0b sparse pointer use of zero as null
Get rid of sparse related warnings from places that use integer as NULL
pointer.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-18 14:37:31 -07:00
Alan Cox
01839f6dde libata-sff: Correct use of check_status()
ata_check_status() does an SFF compliant check
ata_chk_status() does a generic call to ap->ops->check_status (usually
ata_check_status)

libata-sff uses the wrong one. Hardly suprising given the naming here,
which ought to get fixed to ata_sff_check_status() perhaps ?

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-17 20:49:02 -04:00
Tejun Heo
cbcdd87593 libata: implement and use ata_port_desc() to report port configuration
Currently, port configuration reporting has the following problems.

* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
  non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.

This patch implements and uses ata_port_desc() and
ata_port_pbar_desc().  ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ".  ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.

LLD pushes whatever description it wants using the above two
functions.  The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".

SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions.  In many cases,
such controllers need to report different things anyway.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:37 -04:00
Jeff Garzik
6d32d30f55 [libata] Remove ->irq_ack() hook, and ata_dummy_irq_on()
* ->irq_ack() is redundant to what the irq handler already
  performs... chk-status + irq-clear.  Furthermore, it is only
  called in one place, when screaming-irq-debugging is enabled,
  so we don't want to bother with a hook just for that.

* ata_dummy_irq_on() is only ever used in drivers that have
  no callpath reaching ->irq_on().  Remove .irq_on hook from
  those drivers, and the now-unused ata_dummy_irq_on()

Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:34 -04:00
Tejun Heo
936fd73286 libata-link: linkify PHY-related functions
Make the following PHY-related functions to deal with ata_link instead
of ata_port.

* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Tejun Heo
9af5c9c97d libata-link: introduce ata_link
Introduce ata_link.  It abstracts PHY and sits between ata_port and
ata_device.  This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port.  Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.

This patch only defines the host link.  Multiple link handling will be
added later.  Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.

This patch introduces no behavior change.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-12 14:55:30 -04:00
Alan Cox
e1cc9de836 libata-sff: Fix documentation
Code moved to ioread/iowrite but the comment didn't
Also note a posting issue

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-09-20 15:58:26 -04:00
Alan Cox
6fdc99a224 libata-sff; Unbreak non DMA capable controllers again
Seems nobody else is checking/testing this case as it keeps getting
horked.

If we have no BAR4 mapping on an SFF controller this is *NOT* an error,
it just means it isn't doing BMDMA.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-08-01 10:00:56 -04:00
Petr Vandrovec
fe36cb53cf [libata] Fix reported task file values in sense data
ata_tf_read was setting HOB bit when lba48 command was submitted, but
was not clearing it before reading "normal" data.  As it is only place
which sets HOB bit in control register, and register reads should not
be affected by other bits, let's just clear it when we are done with
reading upper bytes so non-48bit commands do not have to touch ctl
at all.

pata_scc suffered from same problem...

Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20 07:44:44 -04:00
Dave Jones
f3a03b0934 Correct comment in libata-sff.c
The filename in the file header is incorrect.

Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-20 07:16:24 -04:00