This patch adds the 82576 device to the description for igb in Kconfig.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch it is possible to select drivers which require
bestcomm support without bestcomm support being selected. This
patch reworks the bestcomm dependencies to ensure the correct
bestcomm tasks are always enabled.
Reported-by: Hans Lehmann <hans.lehmann@ritter-elektronik.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.
There is an existing smc911x driver in the tree; this is intended to
replace it. Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.
This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.
This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: Bahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: Dustin Mcintire <dustin@sensoria.com>
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.
- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
IPv6-specific routines. Both regular bonds and VLANs over bonds
are supported.
- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
IPv6 Neighbor Advertisements that are sent on a failover event.
Default is 1.
- Creates two new IPv6 neighbor discovery functions:
ndisc_build_skb()
ndisc_send_skb()
These were required to support VLANs since we have to be able to
add the VLAN id to the skb since ndisc_send_na() and friends
shouldn't be asked to do this. These two routines are basically
__ndisc_send() split into two pieces, in a slightly different order.
- Updates Documentation/networking/bonding.txt and bumps the rev of bond
support to 3.4.0.
On failover, this new code will generate one packet:
- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
learn that the address has moved to the new slave.
Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The bool kconfig option added to ixgbe and myri10ge for DCA is ambigous,
so this patch adds a description to the kconfig option.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (29 commits)
tcp: Restore ordering of TCP options for the sake of inter-operability
net: Fix disjunct computation of netdev features
sctp: Fix to handle SHUTDOWN in SHUTDOWN_RECEIVED state
sctp: Fix to handle SHUTDOWN in SHUTDOWN-PENDING state
sctp: Add check for the TSN field of the SHUTDOWN chunk
sctp: Drop ICMP packet too big message with MTU larger than current PMTU
p54: enable 2.4/5GHz spectrum by eeprom bits.
orinoco: reduce stack usage in firmware download path
ath5k: fix suspend-related oops on rmmod
[netdrvr] fec_mpc52xx: Implement polling, to make netconsole work.
qlge: Fix MSI/legacy single interrupt bug.
smc911x: Make the driver safer on SMP
smc911x: Add IRQ polarity configuration
smc911x: Allow Kconfig dependency on ARM
sis190: add identifier for Atheros AR8021 PHY
8139x: reduce message severity on driver overlap
igb: add IGB_DCA instead of selecting INTEL_IOATDMA
igb: fix tx data corruption with transition to L0s on 82575
ehea: Fix memory hotplug support
netdev: DM9000: remove BLACKFIN hacking in DM9000 netdev driver
...
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6:
xtensa: Add config files for Diamond 232L - Rev B processor variant
xtensa: Fix io regions
xtensa: Add support for the Sonic Ethernet device for the XT2000 board.
xtensa: replace remaining __FUNCTION__ occurrences
xtensa: use newer __SPIN_LOCK_UNLOCKED macro
XTENSA: warn about including <asm/rwsem.h> directly.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Reject dynamic memory add/remove when ehca adapter is present
IB/ehca: Fix reported max number of QPs and CQs in systems with >1 adapter
IPoIB: Set netdev offload features properly for child (VLAN) interfaces
IPoIB: Clean up ethtool support
mlx4_core: Add Ethernet PCI device IDs
mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC
mlx4_core: Multiple port type support
mlx4_core: Ethernet MAC/VLAN management
mlx4_core: Get ethernet MTU and default address from firmware
mlx4_core: Support multiple pre-reserved QP regions
Update NetEffect maintainer emails to Intel emails
RDMA/cxgb3: Remove cmid reference on tid allocation failures
IB/mad: Use krealloc() to resize snoop table
IPoIB: Always initialize poll_timer to avoid crash on unload
IB/ehca: Don't allow creating UC QP with SRQ
mlx4_core: Add QP range reservation support
RDMA/ucma: Test ucma_alloc_multicast() return against NULL, not with IS_ERR()
The Mellanox ConnectX can operate as an InfiniBand adapter, as an
Ethernet NIC, or as a Fibre Channel (FC) HBA. The kernel has a
low-level driver, mlx4_core, which handles multiplexing access to the
device, and there is also already an InfiniBad driver, mlx4_ib.
This patch adds a new driver, mlx4_en, which implements a standard
Ethernet NIC driver.
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since more ARM platforms use this device, it is easier to add a
dependency on ARM rather than individual platforms.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add a bool IGB_DCA defined to y if IGB and DCA are enabled, but IGB isn't y while DCA=m. And thus remove the need to select INTEL_IOATDMA when IGB is enabled, so that non-x86 architectures can build the igb driver.
Based on work/patch from Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
RBTX4939 board has SMC91X chip and there can be other MIPS boards with
that chip. Make SMC91X selectable on all MIPS board would be better than
enumerating each boards in Kconfig.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: jeff@garzik.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We cannot select INTEL_IOATDMA in Kconfig as soon as MYRI10GE or IXGBE
is enabled since the former is not available on all architectures.
Just use a Kconfig bool {IXGBE,MYRI10GE}_DCA set to =y when DCA
support can actually be built.
[myri10ge portion written and signed-off-by] Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I don't think the enic driver has anything to do with Mark Everett
(http://en.wikipedia.org/wiki/A_Man_Called_E). Fix the Kconfig
description.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
Remove the EXPERIMENTAL label from the atl1 driver and change the vendor
name to include Attansic's successor, Atheros. We'll leave Attansic in
the name since Attansic's PCI ID (1969) is encoded in the PCI config and
is what users encounter on their systems.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for i.MX31ADS board to the cs89x0 ethernet driver.
Rework Kconfig options for the cs89x0 driver to reduce the #ifdef
clutter.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the e1000/e1000e split, no hardware supported by e1000
supports packet split, just remove the Kconfig option and associated
code from the driver.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that arch/ppc is dead CONFIG_PPC_MERGE is always defined for all
powerpc platforms so we don't need to depend on it.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Use DCA in myri10ge when CONFIG_DCA_MODULE is set as well.
And thus force INTEL_IOATDMA to =y so that DCA=y if we are =y.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/built-in.o: In function `rtl8169_gset_xmii':
r8169.c:(.text+0x82259): undefined reference to `mii_ethtool_gset'
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ixgbe can depend on dca IF it is enabled. So if we are compiled as
IXGBE=y, and DCA is enabled, then we must force INTEL_IOATDMA and therefore
DCA to be =y also.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Switch mv643xx_eth from using drivers/net/mii.c to using phylib.
Since the mv643xx_eth hardware does all the link state handling and
PHY polling, the driver will use phylib in the "Doing it all yourself"
mode described in the phylib documentation.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Driver for Atheros L2 10/100 network device. Includes necessary
changes for Kconfig, Makefile, and pci_ids.h.
Signed-off-by: Chris Snook <csnook@redhat.com>
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
so update things accordingly
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After some cleanups in arch/mips area, now MACH_TX49XX is selected for
both TOSHIBA_RBTX4927 and TOSHIBA_RBTX4938. Fold these two conditions
to one.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support SH7619 Internal ethernet controler.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SH7763 has Ethernet core same as SH7710/SH7712.
Positions of some registry are different, but the basic part is the same.
I add support of ethernet of sh7763 to sh_eth.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Full patch for the Atheros L1E Gigabit Ethernet driver.
Supportring AR8121, AR8113 and AR8114
Signed-off-by: Jie Yang <jie.yang @atheros.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
Looking at older kernel sources the APOLLO_ELPLUS option was added
somewhere during kernel 2.1, but even kernel 2.2.0 does not contain
any driver that would be enabled through it...
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The only user of the board, the extremly dated and rare MIPS Atlas board,
has been removed, so this driver can go, too.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the use of the inet_lro module to provide
software LRO support.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
network maintainers suggest NAPI only drivers are the only way to go.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It will almost unavoidably cause some breakage but it
is long overdue.
The driver identification string has been updated, a
lost tabulation and some unused code have been removed.
Otherwise the code paths should stay the same.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
We do not want to prolong the situation much longer that e1000
and e1000e support these devices at the same time. As a result,
take out the bandage that was added for the interim period
and remove all the PCI Express device IDs from e1000.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Support for in-kernel LRO with the ability to enable/disable via ethtool
based on comments from Ben Hutchings.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The ENC28J60 driver ended up adding itself inbetween the
two DM9000 Kconfig entries, so re-unite the two together.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The DM9000's internal PHY reports a copy of the link status
in the NSR register of the chip. Reading the status when
polling for link status is faster as it eliminates the need
to sleep, but does not print as much information.
Add an platform flag to force this behaviour, and a Kconfig
option to allow it to be forced to the faster method always.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Supporting the 57711 and 57711E - refers to in the code as E1H. The
57710 is referred to as E1.
To support the new members in the family, the bnx2x structure was
divided to 3 parts: common, port and function. These changes caused some
rearrangement in the bnx2x.h file.
A set of accessories macros were added to make access to the bnx2x
structure more readable
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The arch/ppc sub-tree has been removed in the powerpc git tree. The old
ibm_emac driver is no longer used by anything as a result of this. This
removes it, leaving the ibm_newemac driver as the proper driver to use for
PowerPC boards with the EMAC hardware.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for Renesas SuperH Ethernet controller. This driver supports
SH7710 and SH7712.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable the smc911x driver for the SuperH architecture. While at it remove
the unused SMC_USE_SH_DMA definition.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that walk_memory_resource() is available regardless of
MEMORY_HOTPLUG's setting, this dependency is not needed.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
As the driver has the standard way to handle PSK, deprecate the old
interface.
Signed-off-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cxgb3 uses lro_* functions and selects INET_LRO, but this doesn't help unless
INET is already enabled, so make the driver depend on INET also.
sge.c:(.text+0x9f09a): undefined reference to `lro_flush_all'
sge.c:(.text+0x9f62f): undefined reference to `lro_receive_skb'
sge.c:(.text+0x9f8a3): undefined reference to `lro_receive_frags'
sge.c:(.text+0x9fbe0): undefined reference to `lro_vlan_hwaccel_receive_skb'
sge.c:(.text+0x9ffcd): undefined reference to `lro_vlan_hwaccel_receive_frags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Make this driver compile cleanly on 64 bit platforms.
Compile tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch introduces code to register and unregister the tg3 mdio bus
with the system.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has been superseded by fs_enet and is no longer in use.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new ehea memory hot plug implementation depends on MEMORY_HOTPLUG.
Signed-off-by: Hannes Hering <hering2@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Delete the non-napi code from the driver and Kconfig.
Tested x86_64. Apply at next open opportunity.
Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (53 commits)
tcp: Overflow bug in Vegas
[IPv4] UFO: prevent generation of chained skb destined to UFO device
iwlwifi: move the selects to the tristate drivers
ipv4: annotate a few functions __init in ipconfig.c
atm: ambassador: vcc_sf semaphore to mutex
MAINTAINERS: The socketcan-core list is subscribers-only.
netfilter: nf_conntrack: padding breaks conntrack hash on ARM
ipv4: Update MTU to all related cache entries in ip_rt_frag_needed()
sch_sfq: use del_timer_sync() in sfq_destroy()
net: Add compat support for getsockopt (MCAST_MSFILTER)
net: Several cleanups for the setsockopt compat support.
ipvs: fix oops in backup for fwmark conn templates
bridge: kernel panic when unloading bridge module
bridge: fix error handling in br_add_if()
netfilter: {nfnetlink,ip,ip6}_queue: fix skb_over_panic when enlarging packets
netfilter: x_tables: fix net namespace leak when reading /proc/net/xxx_tables_names
netfilter: xt_TCPOPTSTRIP: signed tcphoff for ipv6_skip_exthdr() retval
tcp: Limit cwnd growth when deferring for GSO
tcp: Allow send-limited cwnd to grow up to max_burst when gso disabled
[netdrvr] gianfar: Determine TBIPA value dynamically
...
The driver supports the 10Xpress PHY and XFP modules on our reference
designs SFE4001 and SFE4002 and the SMC models SMC10GPCIe-XFP and
SMC10GPCIe-10BT.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The platform is actually named routerboard 532 so let's call it this.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
... and isn't possible on sparc32 boxen anyway, unless somebody
had done JavaStation with PCIE lately.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (49 commits)
[POWERPC] Add zImage.iseries to arch/powerpc/boot/.gitignore
[POWERPC] bootwrapper: fix build error on virtex405-head.S
[POWERPC] 4xx: Fix 460GT support to not enable FPU
[POWERPC] 4xx: Add NOR FLASH entries to Canyonlands and Glacier dts
[POWERPC] Xilinx: of_serial support for Xilinx uart 16550.
[POWERPC] Xilinx: boot support for Xilinx uart 16550.
[POWERPC] celleb: Add support for PCI Express
[POWERPC] celleb: Move miscellaneous files for Beat
[POWERPC] celleb: Move a file for SPU on Beat
[POWERPC] celleb: Move files for Beat mmu and iommu
[POWERPC] celleb: Move files for Beat hvcall interfaces
[POWERPC] celleb: Move the SCC related code for celleb
[POWERPC] celleb: Move the files for celleb base support
[POWERPC] celleb: Consolidate io-workarounds code
[POWERPC] cell: Generalize io-workarounds code
[POWERPC] Add CONFIG_PPC_PSERIES_DEBUG to enable debugging for platforms/pseries
[POWERPC] Convert from DBG() to pr_debug() in platforms/pseries/
[POWERPC] Register udbg console early on pseries LPAR
[POWERPC] Mark udbg console as CON_ANYTIME, ie. callable early in boot
[POWERPC] Set udbg_console index to 0
...
The PS3 gelic network driver depends on the wake-on-lan support
provided by the PS3 sys manager driver. Add that dependency
to the GELIC_NET Kconfig option.
Prevents these build errors:
ps3_gelic_net.c:1277: undefined reference to `.ps3_sys_manager_get_wol'
ps3_gelic_net.c:1337: undefined reference to `.ps3_sys_manager_set_wol'
CC: Masakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the tc35815 driver to use the generic PHY layer in
drivers/net/phy. Also rename 'boardtype' to 'chiptype' which hould be
more appropriate.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/pasemi_mac.c is enabled by CONFIG_PASEMI_MAC, which depends on
PPC64 && PCI. However pasemi_mac.c uses several routines that are only
built when PPC_PASEMI is selected. This can lead to an unbuildable config:
ERROR: ".pasemi_dma_start_chan" [drivers/net/pasemi_mac.ko] undefined!
So make CONFIG_PASEMI_MAC depend on PPC_PASEMI instead of PPC64.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for the IDT rc32434 Ethernet MAC
we can find in the IDT boards and the Mikrotik RB500.
Driver references some code from the linux-mips RB500
support.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Philip Rischel <rischelp@idt.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
| CC drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Acked-by: Masakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Alexander Duyck