Identifiaction of another revision of 88w8385 in sdio mode.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix section mismatch by changing variable name to match one of the
whitelisted (allowable) names for pointing into init data:
WARNING: vmlinux.o(.data+0xce618): Section mismatch: reference to .init.data:prism2_plx_id_table (between 'prism2_plx_drv_id' and 'dev_info')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver checks status of PCI power management to mark
default setting of Wake On Lan. On some systems this works, but often
it reports a that WOL is disabled when it isn't.
This patch gets rid of that check and just reports the wake on
lan status based on the hardware capablity.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch might fix problems with 4G or more of memory.
It stops the driver from doing a small optimization for Tx and Rx,
and instead always sets the high-page on tx/rx descriptors.
Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=9725
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
51bf2976b5 caused a regression in the asix
usbnet driver. usb_control_msg returns the number of bytes read on
success, not 0. Tested with NETGEAR FA120.
Signed-off-by: Russ Dill <Russ.Dill@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move the ip1000 driver into the expected place for gigabit cards
in the configuration menu structure. It should be under the gigabit
cards, not at the top level.
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is probably a result of the changes from commit
854d836 - [NET]: Dynamically allocate the loopback device, part 2
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In order to release PnP resources a card type must be set to EL3_PNP.
Previously, it was never set hence the PnP resources were not
released and device was left in incorrect state.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Here's the reworked patch.
This cleans up some unnecessary byte-swapping while setting up tx and
interpreting rx desc. The 64 bit rx status data should be converted
to host endian format only once and the macros just need to extract
bitfields.
This saves a spate of interrupts on pseries blades caused by buggy
(non) processing rx status ring.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
netxen driver allows limited number of threads simultaneously posting
skb's in tx ring. If transmit slot is unavailable, driver calls
schedule() or loops in xmit_frame().
This patch returns TX_BUSY and lets the stack reschedule the packet if
transmit slot is unavailable. Also removes unnecessary check for tx
timeout in the driver itself, the network stack does that anyway.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes bug that doesn't quiesce second port when interface is
brought down, which could lead to unwarranted interrupt during rmmod /
ifdown.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bumping up driver version to 3.4.18, several fixes have gone in since
version 3.4.2.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* (trivial) endianness annotations
* don't bother with del_timer() from the inside of timer handler itself
* disable_ast() really ought to do del_timer_sync(), not del_timer()
* clean the timer handling in general.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* descriptors inside the rx and tx rings are l-e
* don't cpu_to_le32() the argument of outl()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't allow to nest macvlan devices since it will cause lockdep
warnings and isn't really useful for anything.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the size of the ieee80211 header during rxdone
and make sure the data behind the ieee80211 header
is placed on a 4 byte boundary.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac is a pointer, obviously we shouldn't use the address
of a pointer as MAC address.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes it happens in the tx path that an entry given to the hardware isn't
reported in the txdone handler. This ultimately led to the dreaded "non-free
entry in the non-full queue" message and the stopping of the tx queue. Work
around this issue by allowing the driver to also clear out previos entries in
the txdone handler.
Signed-off-by: Mattias Nissler <mattias.nissler@gmx.de>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From: Mirko Lindner <mlindner@marvell.com>
This patch makes necessary changes in the Neptune driver to support
the new Marvell PHY. It also adds support for the LED blinking
on Neptune cards with Marvell PHY. All registers are using defines
in the niu.h header file as is already done for the BCM8704 registers.
[ Coding style, etc. cleanups -DaveM ]
Signed-off-by: David S. Miller <davem@davemloft.net>
For cards that initially have the MAC address stored in reverse order,
the forcedeth driver uses a flag to signal whether the address was
already corrected, so that it is not reversed again on a subsequent
probe.
Unfortunately this flag, which is stored in a register of the card,
seems to get lost during suspend, resulting in the MAC address being
reversed again. To fix that, the MAC address needs to be written back
in reversed order before we suspend and the flag needs to be reset.
The flag is still required because at least kexec will never write
back the reversed address and thus needs to know what state the card
is in.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
usb_control_msg was changed long ago (2.6.12-pre) to take milliseconds
instead of jiffies. Oddly, mcs7830 wasn't added until 2.6.19-rc3.
Signed-off-by: Russ Dill <Russ.Dill@asu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in 2.6.12-pre, usb_start_wait_urb was switched over to take
milliseconds instead of jiffies. kaweth.c was never updated to match.
Signed-off-by: Russ Dill <Russ.Dill@asu.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the ->poll() routines of the E100, E1000, E1000E, IXGB, and
IXGBE drivers complete ->poll() consistently.
Now they will all break out when the amount of RX work done is less
than 'budget'.
At a later time, we may want put back code to include the TX work as
well (as at least one other NAPI driver does, but by in large NAPI
drivers do not do this). But if so, it should be done consistently
across the board to all of these drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Auke Kok <auke-jan.h.kok@intel.com>
When we add the generic napi_disable_pending() breakout
logic to net_rx_action() it means that napi_disable()
can cause NAPI poll interrupt events to be disabled.
And this is exactly what we want. If a napi_disable()
is pending, and we are looping in the ->poll(), we want
->poll() event interrupts to stay disabled and we want
to complete the NAPI poll ASAP.
When ->poll() break out during device down was being handled on a
per-driver basis, often these drivers would turn interrupts back on
when '!netif_running()' was detected.
And this would just cause a reschedule of the NAPI ->poll() in the
interrupt handler before the napi_disable() could get in there and
grab the NAPI_STATE_SCHED bit.
The vast majority of drivers don't care if napi_disable() might have
the side effect of disabling NAPI ->poll() event interrupts. In all
such cases, when a napi_disable() is performed, the driver just
disabled interrupts or is about to.
However there were three exceptions to this in PCNET32, R8169, and
SKY2. To fix those cases, at the subsequent napi_enable() points, I
added code to ensure that the ->poll() interrupt events are enabled in
the hardware.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Don Fry <pcnet32@verizon.net>
Drivers do this to try to break out of the ->poll()'ing loop
when the device is being brought administratively down.
Now that we have a napi_disable() "pending" state we are going
to solve that problem generically.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the parsing of the RX data header channel field.
The current code parses the header incorrectly and passes a wrong
channel number and frequency for each frame to mac80211.
The FIXMEs added by this patch don't matter for now as the code
where they live won't get executed anyway. They will be fixed later.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This should fix the kernel warn/oops reported while routing.
The tulip driver has a fencepost bug with new NAPI in 2.6.24
It has an off by one bug if a full quantum is reached.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
meth didn't set a valid mac address during probing, but later during
open. Newer kernel refuse to open device with 00:00:00:00:00:00 as mac
address -> dead ethernet. This patch sets the mac address in the probe
function and uses only the mac address from the netdevice struct when
setting up the hardware.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was missed when commit e2ac455a18
fixed the compile errors in drivers/net/netx-eth.c caused by
commit 09f75cd7bf.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the TX ring to have packets sit in it for unbounded
amounts of time.
The only way to defer TX interrupts in the chip is to periodically set
"mark" bits, when processing of a TX descriptor with the mark bit set
is complete it triggers the interrupt for the TX queue's LDG.
A consequence of this kind of scheme is that if packet flow suddenly
stops, the remaining TX packets will just sit there.
If this happens, since those packets could be charged to TCP socket
send queues, such sockets could get stuck.
The simplest solution is to divorce the socket ownership of the packet
once the device takes the SKB, by using skb_orphan() in
niu_start_xmit().
In hindsight, it would have been much nicer if the chip provided two
interrupt sources for TX (like basically every other ethernet chip
does). Namely, keep the "mark" bit, but also signal the LDG when the
TX queue becomes completely empty. That way there is no need to have
a deadlock breaker like this.
Signed-off-by: David S. Miller <davem@davemloft.net>
niu_slowpath_interrupt() expects values to be setup in lp->{v0,v1,v2}
but they aren't. That's only done by niu_schedule_napi() which is
done later in the interrupt path.
If niu_rx_error() returns zero, and v0 is clear, hit the
RX_DMA_CTL_STATE register with a RX_DMA_CTL_STAT_MEX.
Only emit verbose RX error logs if a fatal channel or port error is
signalled. Other cases will be recorded into statistics by
niu_log_rxchan_errors().
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts changeset fa4f0774d7
([CASSINI]: dont touch page_count) because it breaks the driver.
The local page counting added by this changeset did not account
for the asynchronous page count changes done by kfree_skb()
and friends.
The change adds extra atomics and on top of it all appears to be
totally unnecessary as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Nick Piggin <npiggin@suse.de>
Here's proposed fix for RX checksum handling in cassini; it affects
little-endian working with half-duplex gigabit, but obviously needs
testing on big-endian too.
The problem is, we need to convert checksum to fixed-endian *before*
correcting for (unstripped) FCS. On big-endian it won't matter
(conversion is no-op), on little-endian it will, but only if FCS is
not stripped by hardware; i.e. in half-duplex gigabit mode when
->crc_size is set.
cassini.c part is that fix, cassini.h one consists of trivial
endianness annotations. With that applied the sucker is endian-clean,
according to sparse.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move veth.h from net/ to linux/ since it is a user api, and add it to
user header processing Kbuild.
[ Use header-y as suggested by Sam Ravnborg. -DaveM ]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a trivial fix of debug message.
When a persist flag is set, the message should say "enabled".
Signed-off-by: Toyo Abe <tabe@miraclelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially transmit buffer pointers were only reset. But buffer
descriptors were possibly still set as ready, and buffer in upper
layer was not freed. This caused driver hang under big load. Now
reset clean properly the buffer descriptor and freed upper layer.
Signed-off-by: Gregory CLEMENT <gclement00@gmail.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Same story as with olympic - htons(readw()) when swab16(readw()) is needed,
missing conversions to le32 when dealing with shared descriptors, etc.
Olympic got those fixes in 2.4.0-test2, 3c359 didn't.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you need to find a difference between addresses of two
struct members, subtract offsetof() or cast addresses to
char * and subtract those if you prefer it that way. Doing
that same with s/char */u32/, OTOH...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Both store MAC address in CIS; there's no decoder for that
type (0x88) so the drivers work with raw data. It is
byteswapped, so ntohs() works for little-endian, but for
big-endian it's wrong. ntohs(le16_to_cpu()) does the
right thing on both (and always expands to swab16()).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* shift before cpu_to_le64(), not after it
* writel() converts to l-e itself
* misc missing conversions
* in set_multicast() hash_table[] is host-endian; we feed it to card
via writel() and populate it as host-endian, so we'd better put the
first element into it also in host-endian
* pci_unmap_single() et.al. expect host-endian, not little-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_unmap_single() and friends getting a little-endian address...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* usb_control_message() to/from stack (breaks on e.g. arm); some
places did kmalloc() for buffer, some just worked from stack.
Added kmalloc()/memcpy()/kfree() in asix_read_cmd()/asix_write_cmd(),
removed that crap from callers.
* Fixed a leak in ax88172_bind() - on success it forgot to kfree() the
buffer.
* Endianness bug in ax88178_bind() - we read a word from eeprom and work with
it without converting to host-endian
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
txlo_dma_addr should be host-endian; we pass it to typhoon_tso_fill(),
which does arithmetics on it, converts to l-e and passes it to card.
Unfortunately, we forgot le32_to_cpu() when initializing it from
face->txLoAddr, which sits in shared memory and is little-endian.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
rxBuffCleared is little-endian; we miss le32_to_cpu() in checks for
rx ring overruns.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One cpu_to_le16() too many when passing argument for TYPHOON_CMD_XCVR_SELECT;
we end up passing host-endian while the hardware expects little-endian. The
other place doing that (typhoon_start_runtime()) does the right thing, so the
card will recover at the next ifconfig up/tx timeout/resume, which limits the
amount of mess, but still, WTF?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
in typhoon_get_drvinfo() .parm2 is little-endian; not critical
since we just get the firmware id flipped in get_drvinfo output
on big-endian boxen, but...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
txBytes and rxBytesGood are both 64bit; using le32_to_cpu() won't work
on big-endian for obvious reasons.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
if log_len is larger than 4K then we are killing the stack.
allocate on heap instead and limit size to what practically can
be used (PAGE_SIZE)
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves _cancel_deferred_work out of mutex protection and removes
unnecessary mutex in pci_suspend and pci_resume.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some people would like to know what p54 is.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Thanks to Matthias Mueller for reporting this device.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tg3_nvram_write_block_unbuffered() is reading data from nvram into
allocated buffer before overwriting a part of it with user-supplied
data. Then it feeds the entire page back to nvram. It should be
storing the words it had read as little-endian, not as host-endian.
Note that tg3_set_eeprom() does exactly that for padding the same
data to full words before it gets passed down to tg3_nvram_write_block()
and then to tg3_nvram_write_block_unbuffered().
Moreover, when we get to sending the entire thing back to nvram, we
go through it word-by-word, doing essentially
writel(swab32(le32_to_cpu(word)), ...)
so if we want them to reach the card in host-independent endianness,
we'd better really have all that buffer filled with fixed-endian.
For user-supplied part we obviously do have that (it's an array of
octets memcpy'd in), ditto for padding of user-supplied part to word
boundaries (taken care of in tg3_set_eeprom()). The rest of the
buffer gets filled by tg3_nvram_write_block_unbuffered() and it would
damn better be consistent with that (and with tg3_get_eeprom(), while
we are at it - there we also convert the words read from nvram to
little-endian before returning the buffer to user).
The bug should get triggered on big-endian boxen when set_eeprom is done
for less than entire page. Then the words that should've been unaffected
at all will actually get byteswapped in place in nvram.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed misannotations, introduced a new helper - tg3_nvram_read_le().
It gets __le32 * instead of u32 * and puts there the value converted
to little-endian. A lot of callers of tg3_nvram_read() were doing
that; converted them to tg3_nvram_read_le().
At that point the driver is practically endian-clean; the only remaining
place is an actual bug, AFAICS; will be dealt with in the next patch.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes the STATUS_RF_KILL_HW state is not cleared problem if the
device goes to suspend when the rf_kill switch is enabled. The bug causes
the driver always thinks the rf_kill switch is enabled (although it is
disabled) after resume.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes Bug #9414
Since addition of the rfkill callback, the LED associated with the off
switch on the radio has not worked for several reasons:
(1) Essential data in the rfkill structure were missing.
(2) The rfkill structure was initialized after the LED initialization.
(3) There was a minor memory leak if the radio LED structure was inited.
Once the above problems were fixed, additional difficulties were noted:
(4) The radio LED was in the wrong state at startup.
(5) The radio switch had to be manipulated twice for each state change.
(6) A circular mutex locking situation existed.
(7) If rfkill-input is built as a module, it is not automatically loaded.
This patch fixes all of the above.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ia64:
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c: In function `tsf_write_file':
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
drivers/net/wireless/bcm43xx/bcm43xx_debugfs.c:237: warning: long long int format, u64 arg (arg 3)
We do not know what type was used to implement u64 and we can never use u64 in
printk(), sscanf(), etc.
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that libertas selects WIRELESS_EXT, since selecting other stuff that
should depend on WEXT, like IEEE80211, doesn't seem to drag that in for us.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rate control algo reference leak in case if network device has been
failed to register. In this case special flag priv->mac80211_registered is
not set and the rate algo reference is not freeing on module unload. That
leads to OOPs in further ieee80211 rate register/unregister procedure (by
any callee).
It should fix the bug #9470http://bugzilla.kernel.org/show_bug.cgi?id=9470
[akpm@linux-foundation.org: build fix]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Shaddy Baddah found an alignment problem with zd1211rw driver at
2007-11-19. This patch fixes it, it is based on the patch proposed by
Herbert Xu. The alignment 4 has been the agreed value on the
linux-wireless mailing list.
Notify that the problem does only affect the old zd1211rw softmac
driver and not the zd1211rw-mac80211 driver. Daniel Drake has
already provided a patch for the replacement of the softmac
driver, which this patch will break.
Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check in sis190_rx_interrupt() is broken on big-endian
(desc->status is little-endian and everything else actually uses
it correctly, including other checks for OWNbit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit ed7e63a51d has tried to fix
section mismatch:
WARNING: vmlinux.o(.init.text+0x17278): Section mismatch: reference to
.exit.text:uec_mdio_exit (between 'ucc_geth_init' and 'uec_mdio_init')
But that mismatch still happens.
This patch actually fixing section mismatch by removing __exit from
the header file.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[IRDA]: irda parameters warning fixes.
[IRDA]: stir4200 fixes.
[IRDA]: irlmp_unregister_link() needs to free lsaps.
[IRDA]: mcs7780 needs to free allocated rx buffer.
[IRDA]: Race between open and disconnect in irda-usb.
[SCTP]: Flush fragment queue when exiting partial delivery.
[AX25]: Locking dependencies fix in ax25_disconnect().
[IPV4]: Make tcp_input_metrics() get minimum RTO via tcp_rto_min()
[IPV6]: Fix the return value of ipv6_getsockopt
[BRIDGE]: Assign random address.
[IPV4]: Updates to nfsroot documentation
[ATM]: Fix compiler warning noise with FORE200E driver
[NETFILTER]: bridge: fix missing link layer headers on outgoing routed packets
[SYNCPPP]: Endianness and 64bit fixes.
[TIPC]: Fix semaphore handling.
[NETFILTER]: xt_hashlimit should use time_after_eq()
[XFRM]: Display the audited SPI value in host byte order.
[NETFILTER]: ip_tables: fix compat copy race
[NETFILTER]: ctnetlink: set expected bit for related conntracks
From: Olaf Hartmann <olaf.hartmann@s1998.tu-chemnitz.de>
The attached patch observes the stir4200 fifo size and will clear the
fifo, if the size is increasing, while it should be transmitting bytes
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing the mcs7780 based IrDA USB dongle I've stumbled upon
memory leak in mcs_net_close(). Patch below fixes it.
Signed-off-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems to me that irda_usb_net_open() must set self->netopen
under spinlock or disconnect() may fail to kill all URBs, if it is called
while an interface is opened.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* trivial annotations
* long != 32bit, use __be32
* wrong endianness in sending CISCO_ADDR_REPLY
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a device reset (ethtool -r ethX) would cause the
adapter to fall back to regular MTU sizes.
Signed-off-by: Matheos Worku <matheos.worku@sun.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SPIN_LOCK_UNLOCKED is deprecated, use DEFINE_SPINLOCK instead
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Trivial fix to shut up gcc.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The zombie whitespace from outer space that will not die!
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Emil Medve <Emilian.Medve@Freescale.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code used by the non-__devinit s2io_open() mustn't be __devinit.
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.text+0x6f6e3e): Section mismatch: reference to .init.text.20:s2io_test_intr (between 's2io_open' and 's2io_ethtool_sset')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following section mismatch with CONFIG_HOTPLUG=n:
<-- snip -->
...
WARNING: vmlinux.o(.init.text.20+0x4cb25): Section mismatch: reference to .exit.text:sis190_mii_remove (between 'sis190_init_one' and 'read_eeprom')
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
badly broken on big-endian
* passing little-endian to pci_unmap_single() et.al.
* cpu_to_le32() before passing value to writel()
* worse, cpu_to_le64() and shifting/masking result before the same
* hmp->tx_ring[i].status_n_length = cpu_to_le32(
DescEndRing |
(hmp->tx_ring[i].status_n_length & 0x0000FFFF));
is obviously bogus on big-endian. Not hard to untangle, fortunately...
* poisoning addresses in rx_ring is better done after we'd done
pci_unmap_single() on them, not before that. [this one affects little-endian
as well, obviously, provided that pci_unmap_single() is not a no-op on target
in question]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adapted from Ian Wienand <ianw@gelato.unsw.edu.au>
Explicitly free the IRQ before removing the device to remove a
warning "Destroying IRQ without calling free_irq"
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Ian Wienand <ianw@gelato.unsw.edu.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recognized VLAN ids are set via writew(), should go in host-endian.
That's a long-standing bug, BTW - see http://lkml.org/lkml/2004/2/27/180
for example. What happens is that card gets VLAN id table populated by
byteswapped values on little-endian boxen (so 257 works as expected, 256
and 258 do not, etc.). Bug is easily reproduced, patch fixes it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* all places where we assign ->addr get cpu_to_le32(pci_map_single(....)), so
we ought to convert back to host-endian before doing pci_unmap_single() et.al.
* poisoning addresses in netdev_close() should be done _after_ unmapping them,
not before it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I'm using a Marvell 88E8062 on a custom PPC64 blade and ran into RX
lockups while validating the sky2 driver. The receive MAC FIFO would
become stuck during testing with high traffic. One port of the 88E8062
would lockup, while the other port remained functional. Re-inserting
the sky2 module would not fix the problem - only a power cycle would.
I looked over Marvell's most recent sk98lin driver and it looks like
they had a "workaround" for the Yukon XL that the sky2 doesn't have yet.
The sk98lin driver disables the RX MAC FIFO flush feature for all
revisions of the Yukon XL.
According to skgeinit.c of the sk98lin driver, "Flushing must be enabled
(needed for ASF see dev. #4.29), but the flushing mask should be
disabled (see dev. #4.115)". Nice. I implemented this same change in
the sky2 driver and verified that the RX lockup I was seeing was
resolved.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
fpi->cp_command should be overwritten only if CONFIG_PPC_CPM_NEW_BINDING
is NOT set. Otherwise it is already set from the device tree.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 70eba18b56, as per
Jeff Garzik:
"That was meant for 2.6.25, and actually (due to patching) applied to
a completely unrelated 2.6.24 net driver."
Noted-by: Roland Dreier <rdreier@cisco.com>
Requested-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>