Previously we tracked whether the integrity metadata had been remapped
using a request flag. This was fine for low-level retries. However, if
an I/O was redriven by upper layers we would end up remapping again,
causing the retry to fail.
Deprecate the REQ_INTEGRITY flag and introduce BIO_MAPPED_INTEGRITY
which enables filesystems to notify lower layers that the bio in
question has already been remapped.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The bnx2x devices require a 2 second quiet time before sending the last
RAMROD command to destroy a connection. This sleep wait adds up to a
long delay when iscsid is serially destroying maultiple connections.
Create a workqueue to perform the final connection cleanup in the
background to speed up the process. This significantly speeds up the
process as the wait time can be done in parallel for multiple connections.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary beiscsi_put_cid that was freeing up the cid while
in use
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch provides more time for the FW to respond. This became
necessary in boot situations
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fix bug reported by Chuck. And this new version incorporate comments
from Hannes. Please consider to include it into mainline.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Tested-by: Chuck Tuffli <Chuck_Tuffli@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The hw_sector_size variable could overflow if a device reported huge
physical blocks. Switch to the more accurate physical_block_size
terminology and make sure we use an unsigned int to match the range
permitted by READ CAPACITY(16).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds a new MTIOCTOP operation MTWEOFI that writes filemarks with
immediate bit set. This means that the drive does not flush its buffer and the
next file can be started immediately. This speeds up writing in applications
that have to write multiple small files.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sd will get hung up issuing commands to flush write cache if a SAS
device behind the expander is unplugged without warning. Change libsas
to reject commands to domain devices that have already gone away.
[maciej.trela@intel.com: removed setting ->gone in sas_deform_port() to
permit sync cache commands at module removal]
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Tested-by: Haipao Fan <haipao.fan@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To add the Online controller reset support, driver need to do:
a). reset the controller chips -- Xscale and Gen2 which will change
the function calls and add the reset function related to this two
chips.
b). during the reset, driver will store the pending cmds which not
returned by FW to driver's pending queue. Driver will re-issue those
pending cmds again to FW after the OCR finished.
c). In driver's timeout routine, driver will report to OS as reset.
Also driver's queue routine will block the cmds until the OCR
finished.
d). in Driver's ISR routine, if driver get the FW state as state
change, FW in Failure status and FW support online controller
reset (OCR), driver will start to do the controller reset.
e). In driver's IOCTL routine, the application cmds will wait for the
OCR to finish, then issue the cmds to FW.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Update lpfc driver version to 8.3.17
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Replace graceful teardown steps with the singular function reset command.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Fail I/Os with incomplete data that complete with SCSI Check condition.
- Complete aborted I/Os with host_scribble equal to NULL with success.
- Initialize context1 field of iocbq in the new_scsi_buf routines.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add support for bsg MBX_SLI4_CONFIG.
- Multiply linkup timeout in loopback test code by 100.
- Set iocb_stat to 0 in the lpfcdiag_loop_get_xri function.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Added driver support for management application to pass down two security
specific mailbox commands (MBX_SECURITY_MGMT and MBX_AUTH_PORT)
- Added driver support for handling FIPS zeroization trap of host ERATT ER8,
performing selective reset and bringing the device up.
- Added code to detect INIT_LINK mailbox command completion returning status
MBXERR_SEC_NO_PERMISSION.
- Increased the wait timeout on host status register HS_FFRDY and HS_MBRDY
being set.
- Remove the port offline code from the Heartbeat TMO handler.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Move Unload flag earlier in vport deletei to stop ELS traffic
- Replaced some unnecessary spin_lock_irqsave with spin_lock_irq
- Fixed circular spinlock dependency between low-level driver and SCSI midlayer
- Remove duplicate code from lpfc_els_retry routine
- Make all error values negative
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The structure definitions for reporting array errors did not have the correct
size for the Array WWID field. This patch fixes those definitions. It also
fixes part of the output formatting that did not have newlines and fixes size
calculations.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
It was disabled when x86_64 was introduced, but it is reported to be
working on 64bit by two different people, so let's enable it back
again.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: "Juergen E. Fischer" <fischer@norbit.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For ALUA we should be handling all states, independent of whether
the mode is explicit or implicit. For 'Transitioning' we should retry
for a certain amount of time; after that we're setting the port
to 'Standby' and return SCSI_DH_RETRY to signal upper layers
a retry is in order here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fixed the locking and releasing skb in the case of error in the pdu
read path, and added define iscsi_task_cxgbi_data to access the
private data inside the iscsi_task.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If a Virtual I/O server is rebooted, the client fibre channel sees a
transport event on its CRQ, which causes it to attempt to reconnect
to the CRQ. For a period of time during the VIOS reboot, the client's
attempts to register the CRQ will return H_CLOSED, indicating the server
side is not currently registered. The ibmvfc driver was not handling
this well and was taking the virtual adapter offline. Fix this by
re-enabling our interrupt and waiting for the event on our CRQ
indicating the server is back, at which point we can reconnect.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Following a site power outage which re-enabled all the ports on my FC
switches, my system subsequently booted with far too many luns! I had
let it run hoping it would make multi-user. It didn't. :( It hung solid
after exhausting the last sd device, sdzzz, and attempting to create sdaaaa
and beyond. I was unable to get a dump.
Discovered using a 2.6.32.13 based system.
correct this by detecting when the last index is utilized and failing
the sd probe of the device. Patch applies to scsi-misc-2.6.
Signed-off-by: Michael Reed <mdr@sgi.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This adds a fc host dev loss sysfs file. Instead of
calling into the driver using the get_host_def_dev_loss_tmo
callback, we allow drivers to init the dev loss like is done
for other fc host params, and then the fc class will handle
updating the value if the user writes to the new sysfs file.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
It also adds compat support for the driver's existing
dev loss and nodev sysfs and modparams.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
This patch also removes the module dev loss param.
To override the value the fc host sysfs value being
added in the fc class patch can be used instead of the driver
module param.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This removes the driver's get_host_def_dev_loss_tmo
callback and just has the driver set the dev loss
using the fc class fc_host_dev_loss_tmo macro like is
done for other fc params.
This also adds a set rport dev loss function so the
fc class host dev loss tmp sysfs support being added
in the fc class patch can update rports.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We use read/write[bslq] but do not include linux/io.h. This causes
build failures on PPC. Include that file.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Stable Tree <stable@kernel.org>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some cards (like mvsas) have issue troubles if non-NCQ commands are
mixed with NCQ ones. Fix this by using the libata default NCQ check
routine which waits until all NCQ commands are complete before issuing
a non-NCQ one. The impact to cards (like aic94xx) which don't need
this logic should be minimal
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is the new FW HSI blob and the relevant definitions without logic changes.
It also included code adaptation for new HSI. New features are not enabled.
New FW/HSI includes:
- Support for 57712 HW
- Future support for VF (not used)
- Improvements in FW interrupts scheme
- FW FCoE hooks (stubs for future usage)
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The block device drivers have all gained new lock_kernel
calls from a recent pushdown, and some of the drivers
were already using the BKL before.
This turns the BKL into a set of per-driver mutexes.
Still need to check whether this is safe to do.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
What's worse than no comment? A wrong comment.
Several PCMCIA device drivers contained the same comments, which
were based on how the PCMCIA subsystem worked in the old days of 2.4.,
and which were originally part of a "dummy_cs" driver. These comments
no longer matched at all what is happening now, and therefore should
be removed.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
printk() statements on module load or unload are frowned upon. Also,
add a few __init or __exit declarations.
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The Status (CISREG_CCSR) and ExtStatus (CISREG_ESR) registers were
only accessed to enable audio output for some drivers and IRQ for
serial_cs.c. The former also required setting config_req_t.Attributes
to CONF_ENABLE_SPKR; the latter can be simplified to setting this
field to CONF_ENABLE_ESR.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-serial@vger.kernel.org
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Instead of win_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[2,3,4,5] for up to four iomem
ranges. After a call to pcmcia_request_window(), the windows found there
are reserved and may be used until pcmcia_release_window() is called.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-mtd@lists.infradead.org
CC: Jiri Kosina <jkosina@suse.cz>
CC: linux-scsi@vger.kernel.org
Tested-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add support for the Thin Provisioning VPD page and use the TPU and TPWS
bits to switch between UNMAP and WRITE SAME(16) for discards. If no TP
VPD page is present we fall back to old scheme where the max descriptor
count combined with the max lba count are used trigger UNMAP.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We have flattened the BFA hierarchy and also reduced the number of
source and header files we used to have earlier.
Signed-off-by: Krishna Gudipati <kgudipat@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
By default, ibmvfc does not log any async events in order
to avoid flooding the log with them. Improve on this by
logging by default events that are not likely to flood the
log, such as link up/down. Having these events in the log
will improve the ability to debug issues with ibmvfc.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Get rid of init_MUTEX[_LOCKED]() and use sema_init() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: aacraid@adaptec.com
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch updates the scsi_debug virtual LLD to use
root_device_register() and root_device_unregister() from
include/linux/device.h instead of device_register() and
device_unregister() respectively within scsi_debug_init() and
scsi_debug_exit() This simply involved converting the static struct
device pseudo_primary into a pointer that is setup by the call to
root_device_register().
This patch also contains the correct IS_ERR() conditional check of
root_device_register() from within scsi_debug_init().
Thanks to Richard Sharpe and Dmitry Torokhov for their help with this
item.
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix two bugs in the VPD page wrapper:
- Don't return failure if the user asked for page 0
- The end of buffer check failed to account for the page header size
and consequently didn't work
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After the patch "block: remove spurious uses of REQ_HARDBARRIER",
we no longer use 'req' in aic7xxx_buildscb(). Kill it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2nd argument of blk_rq_aligned() has changed to 'unsigned long' by
the previous commit 'block: fix an address space warning in blk-map.c'.
That commit neglected to update a user of that function.
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
All these files use the big kernel lock in a trivial
way to serialize their private file operations,
typically resulting from an earlier semi-automatic
pushdown from VFS.
None of these drivers appears to want to lock against
other code, and they all use the BKL as the top-level
lock in their file operations, meaning that there
is no lock-order inversion problem.
Consequently, we can remove the BKL completely,
replacing it with a per-file mutex in every case.
Using a scripted approach means we can avoid
typos.
file=$1
name=$2
if grep -q lock_kernel ${file} ; then
if grep -q 'include.*linux.mutex.h' ${file} ; then
sed -i '/include.*<linux\/smp_lock.h>/d' ${file}
else
sed -i 's/include.*<linux\/smp_lock.h>.*$/include <linux\/mutex.h>/g' ${file}
fi
sed -i ${file} \
-e "/^#include.*linux.mutex.h/,$ {
1,/^\(static\|int\|long\)/ {
/^\(static\|int\|long\)/istatic DEFINE_MUTEX(${name}_mutex);
} }" \
-e "s/\(un\)*lock_kernel\>[ ]*()/mutex_\1lock(\&${name}_mutex)/g" \
-e '/[ ]*cycle_kernel_lock();/d'
else
sed -i -e '/include.*\<smp_lock.h\>/d' ${file} \
-e '/cycle_kernel_lock()/d'
fi
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Some controllers have a hardware limit on the number of protection
information scatter-gather list segments they can handle.
Introduce a max_integrity_segments limit in the block layer and provide
a new scsi_host_template setting that allows HBA drivers to provide a
value suitable for the hardware.
Add support for honoring the integrity segment limit when merging both
bios and requests.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@carl.home.kernel.dk>
REQ_HARDBARRIER is deprecated. Remove spurious uses in the following
users. Please note that other than osdblk, all other uses were
already spurious before deprecation.
* osdblk: osdblk_rq_fn() won't receive any request with
REQ_HARDBARRIER set. Remove the test for it.
* pktcdvd: use of REQ_HARDBARRIER in pkt_generic_packet() doesn't mean
anything. Removed.
* aic7xxx_old: Setting MSG_ORDERED_Q_TAG on REQ_HARDBARRIER is
spurious. Removed.
* sas_scsi_host: Setting TASK_ATTR_ORDERED on REQ_HARDBARRIER is
spurious. Removed.
* scsi_tcq: The ordered tag path wasn't being used anyway. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@suse.de>
Cc: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Barrier is deemed too heavy and will soon be replaced by FLUSH/FUA
requests. Deprecate barrier. All REQ_HARDBARRIERs are failed with
-EOPNOTSUPP and blk_queue_ordered() is replaced with simpler
blk_queue_flush().
blk_queue_flush() takes combinations of REQ_FLUSH and FUA. If a
device has write cache and can flush it, it should set REQ_FLUSH. If
the device can handle FUA writes, it should also set REQ_FUA.
All blk_queue_ordered() users are converted.
* ORDERED_DRAIN is mapped to 0 which is the default value.
* ORDERED_DRAIN_FLUSH is mapped to REQ_FLUSH.
* ORDERED_DRAIN_FLUSH_FUA is mapped to REQ_FLUSH | REQ_FUA.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alasdair G Kergon <agk@redhat.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Nobody is making meaningful use of ORDERED_BY_TAG now and queue
draining for barrier requests will be removed soon which will render
the advantage of tag ordering moot. Kill ORDERED_BY_TAG. The
following users are affected.
* brd: converted to ORDERED_DRAIN.
* virtio_blk: ORDERED_TAG path was already marked deprecated. Removed.
* xen-blkfront: ORDERED_TAG case dropped.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When an rport is "blocked" and a bsg request is received, the bsg request gets
placed on the queue but the queue stalls. If the fc object is then deleted - the
bsg queue never restarts and keeps the reference on the object, and stops the
overall teardown.
This patch restarts the bsg queue on teardown and drains any pending requests,
allowing the teardown to succeed.
Signed-off-by: Carl Lajeunesse <carl.lajeunesse@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The isr optimization patch that was submitted a few months ago
exposed problems with receiving and handling spurious HRRQ interrutps.
commit 64ffdb7622
Author: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Date: Wed May 19 11:56:13 2010 -0700
[SCSI] ipr: improve interrupt service routine performance
That patch is reverted with this one. A new patch will be submitted
once the issue is better understood and properly handled in the driver.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The previous thin provisioning support was not very user friendly
because it depended on all the relevant options being set on the command
line.
Implement support for the Thin Provisioning VPD page from SBC3 r24 and
add module options for TPU (UNMAP) and TPWS (WRITE SAME (16) with UNMAP
bit). This allows us to have sane default and to enable thin
provisioning with a simple tpu=1 or tpws=1 on the command line depending
on whether we want UNMAP or WRITE SAME behavior.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Return -ENOMEM if the allocations fail.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix typo in scsi_transport_iscsi.c kernel-doc notation:
Warning(drivers/scsi/scsi_transport_iscsi.c:548): No description found for parameter 'cmd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
we're using a pointer through a freed command to reset the request,
which has shown up as an oops with slab poisoning:
Reported-by: Tejun Heo <tj@kernel.org>
Reported-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Commit 409f3499a2 (scsi/sd: remove big
kernel lock) introduced a bug in the sd_release routine. Medium
removal should be allowed when the number of open file references
drops to 0, not when it becomes non-zero.
This patch (as1414) adjusts the test to fix the bug.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Return recovered from pci_mmio_enabled function if it is 82XX.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The sg table size is increased from 128 to 1024 to support multiple sg lists
and number of sg elements per scsi command.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The clearing of local references to rport was blocked when abort is
active. This code clears the local references unconditionaly upon
device loss timeout callback from FC transport.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In case the MPI times out, the FW issues an async event AE8002
to indicate this to every FCoE function. The FC/FCoE driver is
required to handle this, by doing a soft reset and issuing a
Write MPI register mailbox command to reset the MPI.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently the IOs are returned back in slot reset, this
could be late and can cause error handler to invoke.
If error handler invokes, eh_abort fails and escalate to
device/bus/host resets causing issues.
The commands need to be returned back to upper layer in
io_error_detected.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For ISP82xx, the check for empty slot in request queue before posting command type 6
request was missing. This could lead to request queue entry corruptions causing
IO timeouts.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Currently, if target sets the SCSI Status (with Check condition)
and there is no FCP residual bit set then driver does not check
for dropped frame. This could lead to data corruption.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The fw_hung flag should be set ir-respective of if there is a
mbx command pending or not. Also the complete should be called
if there is a mbx waiting.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The seconds_since_last_heartbeat should be checked for consecutive
heartbeat checks. Currently it could happen that seconds_since_last_heartbeat
gets set to max (2 seconds) for non-consecutive heartbeat checks.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We have been seeing the flush request timeout with a wide
range of hardware from tgt+iser to FC targets from a major vendor.
After discussions about if the value should be configurable and
what the best value should be, this patch just increases the flush/sync
cache timeout to 1 minute. 2 minutes was determined to be too long, and
making it configurable was troublesome for users.
This patch was made over Linus's tree. It is not made over scsi-misc
or scsi-rc-fixes, because Linus's had block layer changes that my
patch was built over.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In the case when an ep_connect request is interrupted due to route
request stall, if the iSCSI daemon is terminated by the user, the chip
will be left in a state which will not get cleaned up upon module
removal. Upon module reload, when the same context id is used for a
new connection, chip panic would occur.
This patch adds chip cleanup in the module removal path.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Specific to the Broadcom 10g chipset, the CFC delete operation must be
coupled with the cm_abort/close with does the SRC delete/terminate offload
operation prior.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Acked-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Expanded the TMF request routine to support other TMFs such as LUN
RESET, etc.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
According to RFC3720, nopout packet sent in response to unsolicited
nopin packet requesting a response must retain the TTT of the requester.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes a resource address formatting problem where the first byte
was being zeroed out.
Also, the device ID is now made available as a sysfs attribute.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added cxgb4i iSCSI driver.
This patch implements the cxgb4i iscsi connection acceleration for the
open-iscsi initiator.
The cxgb4i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
[PATCH v5 1/3] libcxgbi: common library for cxgb3i and cxgb4i
From: Karen Xie <kxie@chelsio.com>
Extracts common functions to libcxgbi.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In lpfc_cleanup_pending_mbox() we already have IRQs disabled so we don't
need to disable them again.
Also in lpfc_sli_intr_handler() there is a typo where it has
spin_unlock_irq() instead of just spin_unlock().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Outdent the code following the if.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Patch has only been compile tested.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Patch has only been compile tested.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This fixes a bug where the driver was resetting the
rport dev_loss_tmo when devices were added by adding
support for the get_host_def_dev_loss_tmo callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch adds a fc_host setting to store the
default dev_loss_tmo. It is used if the driver
has a callack to get the value from the LLD. If
the callback is not set, then we use the fc class
module default value.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
GCC warns about empty printf format strings, and after
the addition of %pV these existing such cases in the
scsi driver layer were exposed enough for the compiler
to start seeing them.
Based almost entirely upon a patch by Joe Perches.
[jejb: fix up sym53c8xx msg]
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
warning: zero-length gnu_printf format string
Fix the above warning by inserting a space into the literal string.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The doorbell reset initially appears to work correctly,
the controller resets, comes up, some i/o can even be
done, but on at least some Smart Arrays in some servers,
it eventually causes a subsequent controller lockup due
to some kind of PCIe error, and kdump can end up leaving
the root filesystem in an unbootable state. For this
reason, until the problem is fixed, or at least isolated
to certain hardware enough to be avoided, the doorbell
reset should not be used at all.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The current code in tree has problems with Login.
This patch fixes the Login Failure .
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
[mnc: Can't believe I missed that.]
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Return of the bi_rw tests is no longer bool after commit 74450be1. So
testing against constants doesn't make sense anymore. Fix this bug in
osd_req_read by removing "== 1" in test.
This is not a problem now, where REQ_WRITE is 1, but this can change
in the future and we don't want to rely on that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
gcc-4.0.2:
drivers/scsi/qla4xxx/ql4_os.c: In function 'qla4_8xxx_error_recovery':
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2377: sorry, unimplemented: called from here
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2393: sorry, unimplemented: called from here
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (28 commits)
[SCSI] qla4xxx: fix compilation warning
[SCSI] make error handling more robust in the face of reservations
[SCSI] tgt: fix warning
[SCSI] drivers/message/fusion: Adjust confusing if indentation
[SCSI] Return NEEDS_RETRY for eh commands with status BUSY
[SCSI] ibmvfc: Driver version 1.0.9
[SCSI] ibmvfc: Fix terminate_rport_io
[SCSI] ibmvfc: Fix rport add/delete race resulting in oops
[SCSI] lpfc 8.3.16: Change LPFC driver version to 8.3.16
[SCSI] lpfc 8.3.16: FCoE Discovery and Failover Fixes
[SCSI] lpfc 8.3.16: SLI Additions, updates, and code cleanup
[SCSI] pm8001: introduce missing kfree
[SCSI] qla4xxx: Update driver version to 5.02.00-k3
[SCSI] qla4xxx: Added AER support for ISP82xx
[SCSI] qla4xxx: Handle outstanding mbx cmds on hung f/w scenarios
[SCSI] qla4xxx: updated mbx_sys_info struct to sync with FW 4.6.x
[SCSI] qla4xxx: clear AF_DPC_SCHEDULED flage when exit from do_dpc
[SCSI] qla4xxx: Stop firmware before doing init firmware.
[SCSI] qla4xxx: Use the correct request queue.
[SCSI] qla4xxx: set correct value in sess->recovery_tmo
...
* 'params' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus: (22 commits)
param: don't deref arg in __same_type() checks
param: update drivers/acpi/debug.c to new scheme
param: use module_param in drivers/message/fusion/mptbase.c
ide: use module_param_named rather than module_param_call
param: update drivers/char/ipmi/ipmi_watchdog.c to new scheme
param: lock if_sdio's lbs_helper_name and lbs_fw_name against sysfs changes.
param: lock myri10ge_fw_name against sysfs changes.
param: simple locking for sysfs-writable charp parameters
param: remove unnecessary writable charp
param: add kerneldoc to moduleparam.h
param: locking for kernel parameters
param: make param sections const.
param: use free hook for charp (fix leak of charp parameters)
param: add a free hook to kernel_param_ops.
param: silence .init.text references from param ops
Add param ops struct for hvc_iucv driver.
nfs: update for module_param_named API change
AppArmor: update for module_param_named API change
param: use ops in struct kernel_param, rather than get and set fns directly
param: move the EXPORT_SYMBOL to after the definitions.
...
This driver is the only user of dma_is_consistent(). We plan to remove this
API.
The driver uses the API in the following way:
BUG_ON(!dma_is_consistent(hostdata->dev, pScript) && L1_CACHE_BYTES < dma_get_cache_alignment());
The above code tries to see if L1_CACHE_BYTES is greater than
dma_get_cache_alignment() on sysmtes that can not allocate coherent memory
(some old systems can't).
James Bottomley exmplained that this is necesary because the driver packs the
set of mailboxes into a single coherent area and separates the different
usages by a L1 cache stride. So it's fatal if the dma
He also pointed out that we can kill this checking because we don't hit this
BUG_ON on all architectures that actually use the driver.
(akpm: stolen from the scsi tree because
dma-mapping-remove-dma_is_consistent-api.patch needs it)
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use memdup_user when user data is immediately copied into the
allocated region.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A couple of scsi drivers define a BIT() macro, duplicating the one in
bitops.h.
Cc: Jing Huang <huangj@brocade.com>
Cc: Robert Love <robert.w.love@intel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It appears that the wrong fcport H2I message was tested
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Jing Huang <huangj@Brocade.COM>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's an exported symbol of kernel/printk.c
Rename vprintk and dprintk macros to more common VPRINTK and DPRINTK
Add do { } while(0) around macros
Add level to VPRINTK so KERN_CONT can be used a couple of times.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
String constants that are continued on subsequent lines with \ will cause
spurious whitespace in the resulting output.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In sd_store_cache_type the symbol 'len' is declared twice. Remove the
second declaration to quiet the following sparse warning.
warning: symbol 'len' shadows an earlier one
In sd_probe the variable 'index' is declared as a u32. This variable is
used in a call to ida_get_new which is expecting an int *. Make the
variable an int to quiet the following sparse warning.
warning: incorrect type in argument 2 (different signedness)
There are 4 symbols in the file that are not exported and produce
the following sparse warnings.
warning: symbol 'sd_cdb_cache' was not declared. Should it be static?
warning: symbol 'sd_cdb_pool' was not declared. Should it be static?
warning: symbol 'sd_read_protection_type' was not declared. Should it be static?
warning: symbol 'sd_read_app_tag_own' was not declared. Should it be static?
Make them static to quiet the warnings.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dan's list included:
drivers/scsi/scsi_lib.c +1365 scsi_kill_request(9) warning: variable derefenced in initializer 'cmd'
drivers/scsi/scsi_lib.c +1365 scsi_kill_request(9) warning: variable derefenced before check 'cmd'
We dereference cmd (and possible OOPS if cmd == NULL) before starting the
request so just remove the superfluous debugging code altogether.
[ bart: the potential NULL pointer dereference was finally fixed in
(much later than mine) commit 03b1470 but my patch is still valid ]
Reported-by: Dan Carpenter <error27@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eugene Teo <eteo@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In each case, the destination of the allocation has type struct **, so the
elements of the array should have pointer type, not structure type.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@disable sizeof_type_expr@
type T;
T **x;
@@
x =
<+...sizeof(
- T
+ *x
)...+>
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: Joe Perches <joe@perches.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tag_number reaches dcb->max_command + 1 after the loop, but when
the tag_number equals dcb->max_command an error message is already
issued. The last iteration therefore appears obsolete.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ifdefs are broken so the MMIO code is never compiled and so it's
broken too. Fix them all. Untested as I don't have the hardware.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Andy Walls <awalls@md.metrocast.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove misleading error message that appears after pnp card has been
detected correctly.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At the point where cmnd is initialized, it is tested for NULL, so it
doesn't have to be tested again here.
A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@match exists@
expression x, E;
identifier fld;
@@
* x->fld
... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Besides keeping the line short, the second setting of the MR_DMA_MODE bit
was removed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Willem Riede <osst@riede.org>
Cc: James E.J. Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the writing to sysfs can free the old one, we need to block that
when we access the charp variables.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Jing Huang <huangj@brocade.com>
Cc: James E.J. Bottomley <James.Bottomley@suse.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: user-mode-linux-devel@lists.sourceforge.net
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Fix following warning:
drivers/scsi/qla4xxx/ql4_nx.c: In function 'qla4_8xxx_get_flash_info':
drivers/scsi/qla4xxx/ql4_nx.c:1952: warning: 'mid' may be used uninitialized in this function
drivers/scsi/qla4xxx/ql4_nx.c:1952: note: 'mid' was declared here
drivers/scsi/qla4xxx/ql4_nx.c:1952: warning: 'fid' may be used uninitialized in this function
drivers/scsi/qla4xxx/ql4_nx.c:1952: note: 'fid' was declared here
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
commit 5f91bb050e
Author: Michael Reed <mdr@sgi.com>
Date: Mon Aug 10 11:59:28 2009 -0500
[SCSI] reservation conflict after timeout causes device to be taken offline
Flipped us from always returning failed to always returning success in
the name of fixing the problem where reservation conflict returns from
test unit ready cause the device always to be taken offline.
Unfortuantely, it also introduced a problem whereby for commands other
than test unit ready, the eh dispatcher thinks they succeeded when
reservation conflict is returned, whereas in reality they failed. Fix
this by only returning success for the test unit ready case.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Using scsi_tgt_lib in a new target module, we were getting
the following warning and a stack traceback on every I/O completion:
WARNING: at block/blk-core.c:1108
Which is claiming we may be leaking a bio.
We don't leak bios (blk_rq_unmap_user should free them).
Set rq->bio to NULL before calling scsi_host_put_command().
This was as advised by Fujita Tomonori.
Signed-off-by: Joe Eykholt <jeykholt@cisco.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the transport is busy and we're sending an EH command drivers
occasionally return 'BUSY'. As this in most cases is the TUR
command sent as part of the error recovery this is a sure way
to make the error recovery escalate. Returning 'NEEDS_RETRY'
here will just retry the TUR command and eventually abort the
original command, thus making error handling far smoother.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
To avoid more patches, I also fixed other spelling
and grammar bugs when they were in the same or
following line:
successfull -> successful
parse -> parses
controler -> controller
controlers -> controllers
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
scsi-ml uses REQ_TYPE_BLOCK_PC for flush requests from file
systems. The definition of REQ_TYPE_BLOCK_PC is that we don't retry
requests even when we can (e.g. UNIT ATTENTION) and we send the
response to the callers (then the callers can decide what they want).
We need a workaround such as the commit
77a4229719 to retry BLOCK_PC flush
requests. We will need the similar workaround for discard requests too
since SCSI-ml handle them as BLOCK_PC internally.
This uses REQ_TYPE_FS for flush requests from file systems instead of
REQ_TYPE_BLOCK_PC.
scsi-ml retries only REQ_TYPE_FS requests that have data to
transfer when we can retry them (e.g. UNIT_ATTENTION). However, we
also need to retry REQ_TYPE_FS requests without data because the
callers don't.
This also changes scsi_check_sense() to retry all the REQ_TYPE_FS
requests when appropriate. Thanks to scsi_noretry_cmd(),
REQ_TYPE_BLOCK_PC requests don't be retried as before.
Note that basically, this reverts the commit
77a4229719 since now we use REQ_TYPE_FS
for flush requests.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Jens, any reason why this isn't included in your for-2.6.36 yet?
=
From: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Subject: [PATCH resend] scsi: convert discard to REQ_TYPE_FS from REQ_TYPE_BLOCK_PC
The block layer (file systems) sends discard requests as REQ_TYPE_FS
(the role of REQ_TYPE_FS is that setting up commands and interpreting
the results). But SCSI-ml treats discard requests as
REQ_TYPE_BLOCK_PC.
scsi-ml can handle discard requests as REQ_TYPE_FS
easily. scsi_setup_discard_cmnd() sets up struct request and the bio
nicely. Only remaining issue is that discard requests can't be
completed partially so we need to modify sd_done.
This conversion also fixes the problem that discard requests aren't
retried when possible (e.g. UNIT ATTENTION).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Every user of the BKL in the sd driver is the
result of the pushdown from the block layer
into the open/close/ioctl functions.
The only place that used to rely on the BKL is
the sdkp->openers variable, which gets converted
into an atomic_t.
Nothing else seems to rely on the BKL, since the
functions do not touch global data without holding
another lock, and the open/close functions are
still protected from concurrent execution using
the bdev->bd_mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-scsi@vger.kernel.org
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The open and release block_device_operations are currently
called with the BKL held. In order to change that, we must
first make sure that all drivers that currently rely
on this have no regressions.
This blindly pushes the BKL into all .open and .release
operations for all block drivers to prepare for the
next step. The drivers can subsequently replace the BKL
with their own locks or remove it completely when it can
be shown that it is not needed.
The functions blkdev_get and blkdev_put are the only
remaining users of the big kernel lock in the block
layer, besides a few uses in the ioctl code, none
of which need to serialize with blkdev_{get,put}.
Most of these two functions is also under the protection
of bdev->bd_mutex, including the actual calls to
->open and ->release, and the common code does not
access any global data structures that need the BKL.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
As a preparation for the removal of the big kernel
lock in the block layer, this removes the BKL
from the common ioctl handling code, moving it
into every single driver still using it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We leak a page allocated for discard on some error conditions
(e.g. scsi_prep_state_check returns BLKPREP_DEFER in
scsi_setup_blk_pc_cmnd).
We unprep on requests that weren't prepped in the error path of
scsi_init_io. It makes the error path to clean up scsi commands messy.
Let's strictly apply the rule that we can't unprep on a request that
wasn't prepped.
Calling just scsi_put_command() in the error path of scsi_init_io() is
enough. We don't set REQ_DONTPREP yet.
scsi_setup_discard_cmnd can safely free a page on the error case with
the above rule.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Martin K. Petersen