When the remote device enters the NCQ error state, the device must
be suspended so that the I/O terminations can take place.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TCs must be terminated only while the RNC is suspended. This commit
adds remote device suspensions and resumptions in the abort, reset and
termination paths.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
TCs must only be terminated when RNCs are suspended.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add comprehensive decode for all TC completions that generate RNC
suspensions.
Note that this commit also removes unconditional resumptions of ATAPI
devices when in the SCI_STP_DEV_ATAPI_ERROR state, and STP devices
when in the SCI_STP_DEV_IDLE state. This is because the SCI_STP_DEV_IDLE
and SCI_STP_DEV_ATAPI state entry functions manage the RNC resumption.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The resumption from the Tx/Rx suspended state should work the same
as the Tx suspended state.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
For STP devices under certain protocol conditions, an RNC will not
suspend until the current transfer state is broken with a SYNC/ESC
sequence from the SCU. The SYNC/ESC driven by expiration of the
SCU link layer hang detect timer, which has too small a dynamic
range to support slow SATA devices, so normally it is disabled.
This change enables the timer with the minimum period at the point
when the suspension is requested.
Note that there is potential collateral damage to other open
connections to slow SATA devices on the same port, since there
is no alternative but to enable the LLHANG timer on every phy in
the port for the current suspension request - there is no way to
tell on which phy the RNC in question is currently active.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
[stable v3.0+]
Cc: <stable@vger.kernel.org>
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Ensure we enable receiving BCN's from the
hardware when adding phy to isci_port.
Otherwise if we get BCN before the port is
created we won't see any BCN
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Reported-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch extends timings in COMSAS signaling, so ISCI can detect disc
drives having issues to send COMSAS in correct time frame.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
We can retrieve the shost from the sas_ha like the rest of libsas and
drop this out of our local data structure.
Acked-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
There is a (dubious?) lost irq workaround in sci_controller_isr() that
effectively nullifies attempts to disable interrupts. Until the
workaround can be re-evaluated add some infrastructure to prevent the
interrupt handler from inadvertantly re-enabling interrupts.
The failure mode was interrupts continuing to run after the driver had
been removed and its iomappings torn down.
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Tested-by: Jacek Danecki <jacek.danecki@intel.com>
[richard: clear remaining interrupts at the end of reset]
Acked-by: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The call to wait_for_start() is meant to ensure that all links have been
given a chance to come up before letting the kernel proceed with
probing. However, the implementation is not correctly syncing with the
port configuration agent. In the MPC case the ports are hard-coded, in
the APC case we need to wait for the port-configuration to form ports
from the started phys.
Towards that end increase the timeout for the APC agent to form ports,
and delay start complete until all phys are out of link-training.
Cc: <stable@vger.kernel.org>
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
1/ notify waiters when controller stop completes (fixes 10 second stall
unloading the driver)
2/ make sure phy stop is after port and device stop
Cc: Richard Boyd <richard.g.boyd@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Based on an original implementation by Ed Nadolski and Artur Wojcik
In preparation for S3/S4 support refactor initialization so that
driver-load and resume-from-suspend can share the common init path of
isci_host_init(). Organize the initialization into objects that are
self-contained to the driver (initialized by isci_host_init) versus
those that have some upward registration (initialized at allocation time
asd_sas_phy, asd_sas_port, dma allocations). The largest change is
moving the the validation of the oem and module parameters from
isci_host_init() to isci_host_alloc().
The S3/S4 approach being taken is that libsas will be tasked with
remembering the state of the domain and the lldd is free to be
forgetful. In the case of isci we'll just re-init using a subset of the
normal driver load path.
[clean up some unused / mis-indented function definitions in host.h]
Signed-off-by: Ed Nadolski <edmund.nadolski@intel.com>
Signed-off-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Per the SAS spec, several types of BROADCAST CHANGE primitives
must cause re-discovery of the originating expander.
Only the standard BROADCAST CHANGE primitive was being
sent to the LIBSAS layer. The other BC primitives have been
added to the sci_phy_event_handler()
Signed-off-by: Tom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
domain_device ->parent conveys the same information.
Occurrences of ->is_direct_attached appear next to incomplete open-coded
versions of dev_is_sata(), clean those up as well.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Convert controller state machine warnings to emit the state number (it
missed the number to string conversion, but since these error rarely
happen not much motivation to go further).
Fix up the rnc warnings to use the state name.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPZxSnAAoJEDeqqVYsXL0M0Y4IAMX0vrTVZbg6psA5/gMcWGRP
CkFXEQ8n0PL2SCaj6BoDqamJFe5Nc7dnqxM0fGawB4S9vr3rHhiOlwO+NbV9zFYC
2skBTpeL3sjgtN/jTBdfeeAa7xTYpu/XGyei0NS1A5c2AyMVXV0uYV2s4VNZxe44
tVIn1OEzM2giZ9EB1OZslDMrg5XXm3MBIUECP0LbWUhBm/35caSFKzMXRwhh7WiK
+AVmc2AZYtdEwuknDyiH7KlsaoB3vGL9pPrAUJzIgEhy2pOo2A7W72HfA4Fj+y6a
uF9HBS5zciMp1+sGWry62AjNbWgin9BRlozBEO/lJhIfMGDV1nXEIJsOkOgkdoE=
=1TxB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6
SCSI updates from James Bottomley:
"The update includes the usual assortment of driver updates (lpfc,
qla2xxx, qla4xxx, bfa, bnx2fc, bnx2i, isci, fcoe, hpsa) plus a huge
amount of infrastructure work in the SAS library and transport class
as well as an iSCSI update. There's also a new SCSI based virtio
driver."
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (177 commits)
[SCSI] qla4xxx: Update driver version to 5.02.00-k15
[SCSI] qla4xxx: trivial cleanup
[SCSI] qla4xxx: Fix sparse warning
[SCSI] qla4xxx: Add support for multiple session per host.
[SCSI] qla4xxx: Export CHAP index as sysfs attribute
[SCSI] scsi_transport: Export CHAP index as sysfs attribute
[SCSI] qla4xxx: Add support to display CHAP list and delete CHAP entry
[SCSI] iscsi_transport: Add support to display CHAP list and delete CHAP entry
[SCSI] pm8001: fix endian issue with code optimization.
[SCSI] pm8001: Fix possible racing condition.
[SCSI] pm8001: Fix bogus interrupt state flag issue.
[SCSI] ipr: update PCI ID definitions for new adapters
[SCSI] qla2xxx: handle default case in qla2x00_request_firmware()
[SCSI] isci: improvements in driver unloading routine
[SCSI] isci: improve phy event warnings
[SCSI] isci: debug, provide state-enum-to-string conversions
[SCSI] scsi_transport_sas: 'enable' phys on reset
[SCSI] libsas: don't recover end devices attached to disabled phys
[SCSI] libsas: fixup target_port_protocols for expanders that don't report sata
[SCSI] libsas: set attached device type and target protocols for local phys
...
Pull kmap_atomic cleanup from Cong Wang.
It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().
Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.
* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
drbd: remove the second argument of k[un]map_atomic()
zcache: remove the second argument of k[un]map_atomic()
gma500: remove the second argument of k[un]map_atomic()
dm: remove the second argument of k[un]map_atomic()
tomoyo: remove the second argument of k[un]map_atomic()
sunrpc: remove the second argument of k[un]map_atomic()
rds: remove the second argument of k[un]map_atomic()
net: remove the second argument of k[un]map_atomic()
mm: remove the second argument of k[un]map_atomic()
lib: remove the second argument of k[un]map_atomic()
power: remove the second argument of k[un]map_atomic()
kdb: remove the second argument of k[un]map_atomic()
udf: remove the second argument of k[un]map_atomic()
ubifs: remove the second argument of k[un]map_atomic()
squashfs: remove the second argument of k[un]map_atomic()
reiserfs: remove the second argument of k[un]map_atomic()
ocfs2: remove the second argument of k[un]map_atomic()
ntfs: remove the second argument of k[un]map_atomic()
...
Pull trivial tree from Jiri Kosina:
"It's indeed trivial -- mostly documentation updates and a bunch of
typo fixes from Masanari.
There are also several linux/version.h include removals from Jesper."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (101 commits)
kcore: fix spelling in read_kcore() comment
constify struct pci_dev * in obvious cases
Revert "char: Fix typo in viotape.c"
init: fix wording error in mm_init comment
usb: gadget: Kconfig: fix typo for 'different'
Revert "power, max8998: Include linux/module.h just once in drivers/power/max8998_charger.c"
writeback: fix fn name in writeback_inodes_sb_nr_if_idle() comment header
writeback: fix typo in the writeback_control comment
Documentation: Fix multiple typo in Documentation
tpm_tis: fix tis_lock with respect to RCU
Revert "media: Fix typo in mixer_drv.c and hdmi_drv.c"
Doc: Update numastat.txt
qla4xxx: Add missing spaces to error messages
compiler.h: Fix typo
security: struct security_operations kerneldoc fix
Documentation: broken URL in libata.tmpl
Documentation: broken URL in filesystems.tmpl
mtd: simplify return logic in do_map_probe()
mm: fix comment typo of truncate_inode_pages_range
power: bq27x00: Fix typos in comment
...
This patch fixes scenario where driver removal should be possible
only when driver is in READY state. Also it removes redundant
invocation of routine disabling SCU interrupts - this method is
called somewhere else in driver deinitialization path.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
isci occasionally spews messages like:
isci 0000:03:00.0: sci_phy_event_handler: PHY starting substate machine received unexpected event_code b3940000
...which is not very helpful, since we don't know which controller,
which phy, the exact state, or a decode of the event.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Debugging the driver requires tracing the state transtions and tracing
state names is less work than decoding numbers.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas ata error handling is already async but this does not help the
scan case. Move initial link recovery out from under host->scan_mutex,
and delay synchronization with eh until after all port probe/recovery
work has been queued.
Device ordering is maintained with scan order by still calling
sas_rphy_add() in order of domain discovery.
Since we now scan the domain list when invoking libata-eh we need to be
careful to check for fully initialized ata ports.
Acked-by: Jack Wang <jack_wang@usish.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Prior to commit 61aaff49 "isci: filter broadcast change notifications
during SMP phy resets" we borrowed the MVS_DEV_EH approach from the
mvsas driver for preventing ->lldd_I_T_nexus_reset() events during ata
discovery. This hack was protecting against the old ->phy_reset() in
ata_bus_probe(), but since the conversion to the new error handling this
hack is preventing resets from reaching ata devices.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove ->eh_device_reset_handler() and ->eh_bus_reset_handler() for the
same reason they are not implemented for libata hosts, they cannot be
implemented reliably with ata-eh. ATA error recovery wants to divert
all resets to the eh thread and wait for completion, these handlers may
be invoked from a non-blocking ioctl.
The other path they are called from is libsas-eh, and if we escalate
past I_T_nexus reset we have larger problems i.e. tear down all
in-flight commands in the domain potentially without notification to the
lldd if it has chosen not to implement ->lldd_clear_nexus_port() /
->lldd_clear_nexus_ha().
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Report to libata whether the link to the given domain_device is up and the
signature fis has been received.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Driving resets from libsas-eh is pre-mature as libata will make a
decision about performing a softreset. Currently libata determines
whether to perform a softreset based on ata_eh_followup_srst_needed(),
and none of those conditions apply to isci.
Remove the srst implementation and translate ->lldd_lu_reset() for ata
devices as a request to drive a reset via libata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A hard reset to isci in the direct-attached case is one where the driver
internally manages debouncing the link. In the sas-expander-attached
case a hard reset is one that clears affiliations. The driver should
not be prematurely dropping affiliations at run time, that decision (to
force expander hard resets to ata devices) is left to userspace to
manage. So, arrange for I_T_nexus resets to be sas-link-resets in the
expander-attached case and isci-hard-resets in the direct-attached case.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It only tracks whether the port is stopping in order to gate new devices
being discovered while the port is stopping. However, since the check
and subsequent handling is unlocked there is nothing to stop the port
from going down immediately after the check.
Driver is already prepared to handle devices arriving on stale ports,
and those will be cleaned up by an eventual ->lldd_dev_gone()
notification.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This field is a holdover from the OS abstraction conversion. The stable
phy to port lookups are done via iphy->ownining_port under scic_lock.
After this conversion to use port->lldd_port the only volatile lookup is
the initial lookup in isci_port_formed(). After that point any lookup
via a successfully notified domain_device is guaranteed to be valid
until the domain_device is destroyed.
Delete ->start_complete as it is only set once and is set as a
consequence of the port going link up, by definition of getting a port
formed event the port is "ready".
While we are correcting port lookups also move the asd_sas_port table
out from under the isci_port. This is to preclude any temptation to use
container_of() to convert an asd_sas_port to an isci_port, the
association is dynamic and under libsas control.
Tested-by: Maciej Trela <maciej.trela@intel.com>
[dmilburn@redhat.com: fix i686 compile error]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the direct-attached case this routine returns the phy on which this
device was first discovered. Which is broken if we want to support
wide-targets, as this phy reference can become stale even though the
port is still active.
In the expander-attached case this routine tries to lookup the phy by
scanning the attached sas addresses of the parent expander, and BUG_ONs
if it can't find it. However since eh and the libsas workqueue run
independently we can still be attempting device recovery via eh after
libsas has recorded the device as detached. This is even easier to hit
now that eh is blocked while device domain rediscovery takes place, and
that libata is fed more timed out commands increasing the chances that
it will try to recover the ata device.
Arrange for dev->phy to always point to a last known good phy, it may be
stale after the port is torn down, but it will catch up for wide port
reconfigurations, and never be NULL.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Each libsas driver (mvsas, pm8001, and isci) has invented a different
method for managing the ap->lock. The lock is held by the ata
->queuecommand() path. mvsas drops it prior to acquiring any internal
locks which allows it to hold its internal lock across calls to
task->task_done(). This capability is important as it is the only way
the driver can flush task->task_done() instances to guarantee that it no
longer has any in-flight references to a domain_device at
->lldd_dev_gone() time.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When an lldd invokes ->notify_port_event() it can trigger a chain of libsas
events to:
1/ form the port and find the direct attached device
2/ if the attached device is an expander perform domain discovery
A call to flush_workqueue() will only flush the initial port formation work.
Currently libsas users need to call scsi_flush_work() up to the max depth of
chain (which will grow from 2 to 3 when ata discovery is moved to its own
discovery event). Instead of open coding multiple calls switch to use
drain_workqueue() to flush sas work.
drain_workqueue() does not handle new work submitted during the drain so
libsas needs a bit of infrastructure to hold off unchained work submissions
while a drain is in flight. A lldd ->notify() event is considered 'unchained'
while a sas_discover_event() is 'chained'. As Tejun notes:
"For now, I think it would be best to add private wrapper in libsas to
support deferring unchained work items while draining."
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Per commit 3e4ec344 "libata: kill ATA_FLAG_DISABLED" needing to set
ATA_DEV_NONE is a holdover from before libsas converted to the
"new-style" ata-eh.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows the controller to do WRITE_INSERT and READ_STRIP for SAS
disks that support protection information. SAS disks must be formatted
with protection information to use this feature via sg_format.
sg3_utils-1.32 -- sg_format version 1.19 20110730
sg_format usage:
sg_format --format --verbose --pinfo /dev/sda
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Enabling clock gating for power savings on entry to controller ready
state. Disable SCU clock gating for power savings on exit from the
controller ready state.
The gating is fully automated by silicon after setting the mode.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.
Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When expander connected in x2 or x4 mode and with IO runnning, if
a cable from wideport is plugged out from the phy, IO's start failing
on all the targets.
Observed that when cable is pulled with IO running, cominit is
happening on all the links and IO's start dropping to 0 and eventually
the whole IO fails. Second observation, target is trying to open and
SCU is responding with "Open reject no destination".
A cause of the problem is when the port went from the "ready
configuring substate" back to "ready configuring substate" as a result
of phy being pulled off, scic suspended the port task scheduler
register. As a result no IO was allowed and in the "substate
configuring enter" routine the IO never goes back to 0. As a result
the port never comes out of "ready substate configuring".
The patch adds a mechanism of activate and deactivate phy when a port
link up, which fixes the problem.
Signed-off-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Split scu_link_layer_start_oob function to reset and enable and
add flush after all steps.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the first phy of a wide port comes up, don't report the port ready
yet, always wait for 250 miliseconds then config the port with all phys
added to the port. So that we can avoid reporting wide port device too
early to kernel, which caused the first IOs (report luns, inquirys)
failed due to not all the phys are configured into its port. Changes
also made that the phys in a wide port don't need to go through half
second wait time for consuming power.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When hot insert the wide port device through the mini-sas port,
the first IOs (Report Luns or Inquiry) may fail due to the device
trying to open to a SCU phy that is still in suspended state. This
IO failure causes the wide port device stuck in UPDATING_PORT_WIDTH
state.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Arrange for task_contexts prepared for the wide targets to account for
all the attached phys in the port.
Signed-off-by: Bartek Nowakowski <bartek.nowakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Failure seen pulling a cable from a x4 port configured in manual port
configuration (MPC) mode (MPC mode is set by the the OEM paramaters
provided by the platform or isci_firmware.bin). While IO running to
devices behind and expander, plugging out the cable from phy is causing
IO failures and IO drops on disks and never recover.
It happens because during link up/down the phy were being taken out of
the port.
Fix: during link down the phy is kept in the same logical port.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bump the version now that the driver has atapi support and the initial
round of hotplug fixes. The EXPERIMENTAL tag should have been removed a
while back. While we're here also kill the "select SCSI_SAS_HOST_SMP"
as the build error was separately fixed by commit d962480e "[SCSI]
libsas: fix try_test_sas_gpio_gp_bit() build error".
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As the field was never set, isci_print_tmf() using 'isci_tmf->device'
sometimes causes a kernel crash if the dev_dbg() statement is enabled.
Remove the unused field both from isci_tmf struct definition and from
isci_print_tmf()
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Gen-3 operation is marginal, default to gen-2 for now.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
"No task timeout timer reduced from 20 to 2 This timer controls how
long the SCU hardware will hold open the TX side of the connection
before sending a DONE. The timer allows the hardware to attempt to
optimize the DONE/CLOSE behavior to allow for new COMMAND IU to be
posted. In practice closing the connection quicker is better."
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
v1.3 allows the attenuation of the attached cables to be specified to
the driver in terms of 'short', 'medium', and 'long' (see probe_roms.h).
These settings (per phy) are retrieved from the platform oem-parameters
(BIOS rom) or via a module parameter override.
Reviewed-by: Jiangbi Liu <jiangbi.liu@intel.com>
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
v1.1 allows finer grained tuning of the SSC (spread-spectrum-clocking)
settings for SAS and SATA. See notes in probe_roms.h
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
C1 silicon requires updates to the phy tuning recipe and also support
for user provided cable selects (per-phy) for short, medium, and long
cables. Default to 'short' awaiting support for selecting the cable via
oem parameters.
Reviewed-by: Jiangbi Liu <jiangbi.liu@intel.com>
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Before updating the code to support the latest platform updates and
silicon revision cleanup some of the long deref chains.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This parameter blob and generator program have been moved to the
linux-firmware.git repository.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixes bug where max_concurr_spinup oem parameter should be
overriden by max_concurr_spinup user parameter. Override should
happen only when max_concurr_spinup user parameter is specified
in command line (greater than 0). Also this fix shortens variables
representing max_conxurr_spinup for oem and user parameters.
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The initial bcn filtering implementation was validated on a kernel
baseline that predated the switch to new libata error handling. Also,
prior to that conversion we borrowed the mvsas MVS_DEV_EH approach to
prevent the unwanted extra ap->ops->phy_reset(ap) that occurred in the
ata_bus_probe() path.
After the conversion to new libata eh resets at discovery are more
frequent and get filtered prematurely by IDEV_EH. The result is that
our bcn filtering has been blocked from running and at discovery and it
appears to stall discovery completion to the point of triggering hung
task timeouts. So, revert the implementation for now. When it returns
it will go into libsas proper.
The domain rediscovery that takes place due to ->lldd_I_T_nexus_reset()
events should now be properly waited for by the ata_port_wait_eh() call
in ata_port_probe(). So the hard coded delay in the isci
->lldd_I_T_nexus_reset() and other libsas drivers should help debounce
the libsas thread from seeing temporary device removals.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A hard reset can timeout before or after the last phy in the
port goes away. If after, then notify the OS that the last
phy has failed.
The recovery for the failed hard reset has been removed.
This recovery code was unecessary in that the link would
recover from the failure normally by a new link reset sequence
or hotplug of the remote device.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The lldd does not need to look at or manage the pending device
reset bit in pending sas_tasks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Use the existing IREQ_TMF flag as a request type indicator.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas uses the LLDD abort task interface to handle I/O timeouts
in the SATA/STP and SMP discovery paths, so this change will terminate
STP/SMP requests. Also, if the device is gone, the lldd will prevent
libsas from further escalations in the error handler.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
libsas will cleanup pending sas_tasks after error handler
path functions are called; do not call task_done callbacks.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the case where "task" requests timeout (note that this class of
requests can also include SATA/STP soft reset FIS transmissions),
handle the case where the task was being managed by some call to
terminate the task request by completing both the tmf and the aborting
process.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Make sure terminated requests and completed task tags are freed.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the case where an I/O fails to start in isci_request_execute,
only allow retries if the device is not already gone.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy(). Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.
These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
* /sys/class/sas_phy/<phyX>/invalid_dword_count
* /sys/class/sas_phy/<phyX>/running_disparity_error_count
* /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
* /sys/class/sas_phy/<phyX>/phy_reset_problem_count
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixes a bug where any phy removed from the port set the port
state to "stopping" - do this only when the last phy removed
from the port.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
DONE_CRC_ERR is not a RNC suspension condition, so do not change the
state to expect the incoming suspension notification.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
[djbw: dropped DONE_CMD_LL_R_ERR change]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Since libsas has it's own means to escalate SATA/STP device error
handling depending on task status codes, return all SATA/STP I/O
on the normal path.
i.e. skip sas_task_abort() and let sas_ata_task_done() disposition the
qc. Longer term we want to audit non-essential calls to
sas_task_abort().
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Based on original implementation from Jiangbi Liu and Maciej Trela.
ATAPI transfers happen in two-to-three stages. The two stage atapi
commands are those that include a dma data transfer. The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration. The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.
stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb. Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).
stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.
stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.
To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO). This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).
If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition. However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response. In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Needed to jump to scic_lock unlock.
Also spotted by coccicheck.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Kill the local smp response buffer.
Besides being unnecessary, it is too small (currently truncates
responses to 60 bytes). The mid-layer will have already allocated a
sufficiently sized buffer, just kmap and copy into it directly.
Cc: <stable@kernel.org>
Reported-by: Derick Marks <derick.w.marks@intel.com>
Tested-by: Derick Marks <derick.w.marks@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Basic support to initialize the gpio unit, accept an incomming
SAS_GPIO_REG_TX_GP bitstream, and translate it to the ODx.n fields in
the hardware registers. If register indexes outside the supported range
are specified in the SMP frame we simply accept the write and return how
many registers (SFF-8485) were written (libsas reports this as residue
in the request).
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
output_data_select registers are off by one u32
delete the macros we will never use.
Reported-by: Artur Wojcik <artur.wojcik@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a resend from the original, changing the title from PATCH to
RFC(since this is a review for commit, and I should have put that the first go around).
and also removing some of the commit's with ia64 and bash since it is significant.
let me know if I might have missed anything etc..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Now that isci has added a 3rd open coded user of this functionality just
share the libsas version.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hardware only increments the put pointer on event types >= 4. Do not
increment the get pointer for event type 3.
Reported-by: Kapil Karkra <kapil.karkra@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hardware allows both an outstanding number commands and a timeout value
(whichever occurs first) as a gate to the next interrupt generation. This
scheme at completion time looks at the remaining number of outstanding tasks
and sets the timeout to maximize small transaction operation. If transactions
are large (take more than a few 10s of microseconds to complete) then
performance is not interrupt processing bound, so the small timeouts this
scheme generates are overridden by the time it takes for a completion to
arrive.
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of immediately completing any request that has a second
termination call made on it, wait for the TC done/abort HW event.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Adding API update for adding isci_id entry scsi_host sysfs entry.
Also fixing up the sysfs registration to the scsi_host template
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Need the following workaround in the driver for interoperability with
the older Intel SSD drives and any other SATA drive that may exhibit the
same behavior. This is a corner case where SCU speed is limited to
either 3G or 1.5G and the drive has a period of DC idle when it switches
speed during SATA speed negotiation. Workaround :change PHYTOV[31:24]
from 0x36 to 0x3B.
Signed-off-by: Marcin Tomczak <marcin.tomczak@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The unsolicited frame control infrastructure requires a table of dma
addresses for the hardware to lookup the frame buffer location by an
index. The hardware expects the elements of this table to be 64-bit
quantities, so we cannot reference these elements as dma_addr_t. All
unsolicited frame protocols are affected, particularly SATA-PIO and SMP
which prevented direct-attached SATA drives and expander-attached drives
to not be discovered.
Cc: <stable@kernel.org>
Reported-by: Jacek Danecki <jacek.danecki@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A bug (likely copy/paste) that has been carried from the original
implementation. The unsolicited frame handling structure returns the
d2h fis in the isci_request.stp.rsp buffer.
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The hard_reset parameter passed to the LLDD in the direct-attached
phy control case allows the LLDD to filter link failure events
while the direct-attached device reset is executing.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The messages emitted from task.c and some from request.c likely
duplicate (in a less undertandable way) what is reported by the
midlayer.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Perform checking per-pci device (even though all systems will only have
1 pci device in this generation), and delete support for silicon that
does not report a proper revision (i.e. A0).
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Most of these simple dereference macros are longer than their open coded
equivalent. Deleting enum sci_controller_mode is thrown in for good
measure.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The distinction between scic_sds_ scic_ and sci_ are no longer relevant
so just unify the prefixes on sci_. The distinction between isci_ and
sci_ is historically significant, and useful for comparing the old
'core' to the current Linux driver. 'sci_' represents the former core as
well as the routines that are closer to the hardware and protocol than
their 'isci_' brethren. sci == sas controller interface.
Also unwind the 'sds1' out of the parameter structs.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the distinction between these two implementations and unify on
isci_host (local instances named ihost). Hmmm, we had two
'oem_parameters' instances, one was unused... nice.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Remove the distinction between these two implementations and unify on
isci_remote_device (local instances named idev).
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jeff Skirvin