Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
This work is based on prior code by Andrew Jackson
Signed-off-by: Stuart Hodgson <smhodgson@solarflare.com>
[bwh:
- Add byte order conversion in efx_ptp_send_times()
- Simplify conversion of PPS event times
- Add the built-in vs module check to CONFIG_SFC_PTP dependencies]
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We only use tso_state::full_packet_space to calculate the IPv4 tot_len
or IPv6 payload_len, not to set tso_state::packet_space. Replace it
with an ip_base_len field holding the value of tot_len or payload_len
before including the TCP payload, which is much more useful when
constructing the new headers.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
TSO header buffers contain a control structure immediately followed by
the packet headers, and are kept on a free list when not in use. This
complicates buffer management and tends to result in cache read misses
when we recycle such buffers (particularly if DMA-coherent memory
requires caches to be disabled).
Replace the free list with a simple mapping by descriptor index. We
know that there is always a payload descriptor between any two
descriptors with TSO header buffers, so we can allocate only one
such buffer for each two descriptors.
While we're at it, use a standard error code for allocation failure,
not -1.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We now have a definite upper bound on the number of descriptors per
skb; use that to stop the queue when the next packet might not fit.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add a flags field to struct efx_tx_buffer, replacing the
continuation and map_single booleans.
Since a single descriptor cannot be both a TSO header and the last
descriptor for an skb, unionise efx_tx_buffer::{skb,tsoh} and add
flags for validity of these fields.
Clear all flags in free buffers (whereas previously the continuation
flag would be set).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently an skb requiring TSO may not fit within a minimum-size TX
queue. The TX queue selected for the skb may stall and trigger the TX
watchdog repeatedly (since the problem skb will be retried after the
TX reset). This issue is designated as CVE-2012-3412.
Set the maximum number of TSO segments for our devices to 100. This
should make no difference to behaviour unless the actual MSS is less
than about 700. Increase the minimum TX queue size accordingly to
allow for 2 worst-case skbs, so that there will definitely be space
to add an skb after we wake a queue.
To avoid invalidating existing configurations, change
efx_ethtool_set_ringparam() to fix up values that are too small rather
than returning -EINVAL.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is nothing in the VLAN driver or core VLAN support that
invalidates the TCP and IP header offsets.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
tso_state::packet_space is always set in tso_start_packet(); the
value set in tso_start() is not used, and is also incorrect.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The 'page size' for PCIe DMA, i.e. the alignment of boundaries at
which DMA must be broken, is 4KB. Name this value as EFX_PAGE_SIZE
and use it in efx_max_tx_len(). Redefine EFX_BUF_SIZE as
EFX_PAGE_SIZE since its value is also a result of that requirement,
and use it in efx_init_special_buffer().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The out-of-tree version of the sfc driver used to run a self-test on
each device before registering it. Although this was never included
in-tree, some functions have checks for this special case which is not
really possible.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as skb is pushed to hardware, it can be completed and freed, so
we should not dereference skb anymore.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to sfc to use byte queue limits.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I converted some drivers from pci_map_page to skb_frag_dma_map I
neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and
pci_dma_mapping_error into dma_mapping_error.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steve Hodgson <shodgson@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Moves the Solarflare drivers into drivers/net/ethernet/sfc/ and
make the necessary Kconfig and Makefile changes.
CC: Steve Hodgson <shodgson@solarflare.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stuart Hodgson