linux/sound/soc/codecs/tlv320dac33.c

1612 lines
42 KiB
C
Raw Normal View History

/*
* ALSA SoC Texas Instruments TLV320DAC33 codec driver
*
* Author: Peter Ujfalusi <peter.ujfalusi@nokia.com>
*
* Copyright: (C) 2009 Nokia Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/pm.h>
#include <linux/i2c.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/gpio.h>
#include <linux/regulator/consumer.h>
#include <sound/core.h>
#include <sound/pcm.h>
#include <sound/pcm_params.h>
#include <sound/soc.h>
#include <sound/soc-dapm.h>
#include <sound/initval.h>
#include <sound/tlv.h>
#include <sound/tlv320dac33-plat.h>
#include "tlv320dac33.h"
#define DAC33_BUFFER_SIZE_BYTES 24576 /* bytes, 12288 16 bit words,
* 6144 stereo */
#define DAC33_BUFFER_SIZE_SAMPLES 6144
#define NSAMPLE_MAX 5700
#define LATENCY_TIME_MS 20
#define MODE7_LTHR 10
#define MODE7_UTHR (DAC33_BUFFER_SIZE_SAMPLES - 10)
#define BURST_BASEFREQ_HZ 49152000
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
#define SAMPLES_TO_US(rate, samples) \
(1000000000 / ((rate * 1000) / samples))
#define US_TO_SAMPLES(rate, us) \
(rate / (1000000 / us))
static struct snd_soc_codec *tlv320dac33_codec;
enum dac33_state {
DAC33_IDLE = 0,
DAC33_PREFILL,
DAC33_PLAYBACK,
DAC33_FLUSH,
};
enum dac33_fifo_modes {
DAC33_FIFO_BYPASS = 0,
DAC33_FIFO_MODE1,
DAC33_FIFO_MODE7,
DAC33_FIFO_LAST_MODE,
};
#define DAC33_NUM_SUPPLIES 3
static const char *dac33_supply_names[DAC33_NUM_SUPPLIES] = {
"AVDD",
"DVDD",
"IOVDD",
};
struct tlv320dac33_priv {
struct mutex mutex;
struct workqueue_struct *dac33_wq;
struct work_struct work;
struct snd_soc_codec codec;
struct regulator_bulk_data supplies[DAC33_NUM_SUPPLIES];
int power_gpio;
int chip_power;
int irq;
unsigned int refclk;
unsigned int alarm_threshold; /* set to be half of LATENCY_TIME_MS */
unsigned int nsample_min; /* nsample should not be lower than
* this */
unsigned int nsample_max; /* nsample should not be higher than
* this */
enum dac33_fifo_modes fifo_mode;/* FIFO mode selection */
unsigned int nsample; /* burst read amount from host */
u8 burst_bclkdiv; /* BCLK divider value in burst mode */
unsigned int burst_rate; /* Interface speed in Burst modes */
int keep_bclk; /* Keep the BCLK continuously running
* in FIFO modes */
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
spinlock_t lock;
unsigned long long t_stamp1; /* Time stamp for FIFO modes to */
unsigned long long t_stamp2; /* calculate the FIFO caused delay */
unsigned int mode1_us_burst; /* Time to burst read n number of
* samples */
unsigned int mode7_us_to_lthr; /* Time to reach lthr from uthr */
enum dac33_state state;
};
static const u8 dac33_reg[DAC33_CACHEREGNUM] = {
0x00, 0x00, 0x00, 0x00, /* 0x00 - 0x03 */
0x00, 0x00, 0x00, 0x00, /* 0x04 - 0x07 */
0x00, 0x00, 0x00, 0x00, /* 0x08 - 0x0b */
0x00, 0x00, 0x00, 0x00, /* 0x0c - 0x0f */
0x00, 0x00, 0x00, 0x00, /* 0x10 - 0x13 */
0x00, 0x00, 0x00, 0x00, /* 0x14 - 0x17 */
0x00, 0x00, 0x00, 0x00, /* 0x18 - 0x1b */
0x00, 0x00, 0x00, 0x00, /* 0x1c - 0x1f */
0x00, 0x00, 0x00, 0x00, /* 0x20 - 0x23 */
0x00, 0x00, 0x00, 0x00, /* 0x24 - 0x27 */
0x00, 0x00, 0x00, 0x00, /* 0x28 - 0x2b */
0x00, 0x00, 0x00, 0x80, /* 0x2c - 0x2f */
0x80, 0x00, 0x00, 0x00, /* 0x30 - 0x33 */
0x00, 0x00, 0x00, 0x00, /* 0x34 - 0x37 */
0x00, 0x00, /* 0x38 - 0x39 */
/* Registers 0x3a - 0x3f are reserved */
0x00, 0x00, /* 0x3a - 0x3b */
0x00, 0x00, 0x00, 0x00, /* 0x3c - 0x3f */
0x00, 0x00, 0x00, 0x00, /* 0x40 - 0x43 */
0x00, 0x80, /* 0x44 - 0x45 */
/* Registers 0x46 - 0x47 are reserved */
0x80, 0x80, /* 0x46 - 0x47 */
0x80, 0x00, 0x00, /* 0x48 - 0x4a */
/* Registers 0x4b - 0x7c are reserved */
0x00, /* 0x4b */
0x00, 0x00, 0x00, 0x00, /* 0x4c - 0x4f */
0x00, 0x00, 0x00, 0x00, /* 0x50 - 0x53 */
0x00, 0x00, 0x00, 0x00, /* 0x54 - 0x57 */
0x00, 0x00, 0x00, 0x00, /* 0x58 - 0x5b */
0x00, 0x00, 0x00, 0x00, /* 0x5c - 0x5f */
0x00, 0x00, 0x00, 0x00, /* 0x60 - 0x63 */
0x00, 0x00, 0x00, 0x00, /* 0x64 - 0x67 */
0x00, 0x00, 0x00, 0x00, /* 0x68 - 0x6b */
0x00, 0x00, 0x00, 0x00, /* 0x6c - 0x6f */
0x00, 0x00, 0x00, 0x00, /* 0x70 - 0x73 */
0x00, 0x00, 0x00, 0x00, /* 0x74 - 0x77 */
0x00, 0x00, 0x00, 0x00, /* 0x78 - 0x7b */
0x00, /* 0x7c */
0xda, 0x33, 0x03, /* 0x7d - 0x7f */
};
/* Register read and write */
static inline unsigned int dac33_read_reg_cache(struct snd_soc_codec *codec,
unsigned reg)
{
u8 *cache = codec->reg_cache;
if (reg >= DAC33_CACHEREGNUM)
return 0;
return cache[reg];
}
static inline void dac33_write_reg_cache(struct snd_soc_codec *codec,
u8 reg, u8 value)
{
u8 *cache = codec->reg_cache;
if (reg >= DAC33_CACHEREGNUM)
return;
cache[reg] = value;
}
static int dac33_read(struct snd_soc_codec *codec, unsigned int reg,
u8 *value)
{
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
int val;
*value = reg & 0xff;
/* If powered off, return the cached value */
if (dac33->chip_power) {
val = i2c_smbus_read_byte_data(codec->control_data, value[0]);
if (val < 0) {
dev_err(codec->dev, "Read failed (%d)\n", val);
value[0] = dac33_read_reg_cache(codec, reg);
} else {
value[0] = val;
dac33_write_reg_cache(codec, reg, val);
}
} else {
value[0] = dac33_read_reg_cache(codec, reg);
}
return 0;
}
static int dac33_write(struct snd_soc_codec *codec, unsigned int reg,
unsigned int value)
{
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
u8 data[2];
int ret = 0;
/*
* data is
* D15..D8 dac33 register offset
* D7...D0 register data
*/
data[0] = reg & 0xff;
data[1] = value & 0xff;
dac33_write_reg_cache(codec, data[0], data[1]);
if (dac33->chip_power) {
ret = codec->hw_write(codec->control_data, data, 2);
if (ret != 2)
dev_err(codec->dev, "Write failed (%d)\n", ret);
else
ret = 0;
}
return ret;
}
static int dac33_write_locked(struct snd_soc_codec *codec, unsigned int reg,
unsigned int value)
{
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
int ret;
mutex_lock(&dac33->mutex);
ret = dac33_write(codec, reg, value);
mutex_unlock(&dac33->mutex);
return ret;
}
#define DAC33_I2C_ADDR_AUTOINC 0x80
static int dac33_write16(struct snd_soc_codec *codec, unsigned int reg,
unsigned int value)
{
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
u8 data[3];
int ret = 0;
/*
* data is
* D23..D16 dac33 register offset
* D15..D8 register data MSB
* D7...D0 register data LSB
*/
data[0] = reg & 0xff;
data[1] = (value >> 8) & 0xff;
data[2] = value & 0xff;
dac33_write_reg_cache(codec, data[0], data[1]);
dac33_write_reg_cache(codec, data[0] + 1, data[2]);
if (dac33->chip_power) {
/* We need to set autoincrement mode for 16 bit writes */
data[0] |= DAC33_I2C_ADDR_AUTOINC;
ret = codec->hw_write(codec->control_data, data, 3);
if (ret != 3)
dev_err(codec->dev, "Write failed (%d)\n", ret);
else
ret = 0;
}
return ret;
}
static void dac33_init_chip(struct snd_soc_codec *codec)
{
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
if (unlikely(!dac33->chip_power))
return;
/* 44-46: DAC Control Registers */
/* A : DAC sample rate Fsref/1.5 */
dac33_write(codec, DAC33_DAC_CTRL_A, DAC33_DACRATE(0));
/* B : DAC src=normal, not muted */
dac33_write(codec, DAC33_DAC_CTRL_B, DAC33_DACSRCR_RIGHT |
DAC33_DACSRCL_LEFT);
/* C : (defaults) */
dac33_write(codec, DAC33_DAC_CTRL_C, 0x00);
/* 64-65 : L&R DAC power control
Line In -> OUT 1V/V Gain, DAC -> OUT 4V/V Gain*/
dac33_write(codec, DAC33_LDAC_PWR_CTRL, DAC33_LROUT_GAIN(2));
dac33_write(codec, DAC33_RDAC_PWR_CTRL, DAC33_LROUT_GAIN(2));
/* 73 : volume soft stepping control,
clock source = internal osc (?) */
dac33_write(codec, DAC33_ANA_VOL_SOFT_STEP_CTRL, DAC33_VOLCLKEN);
/* 66 : LOP/LOM Modes */
dac33_write(codec, DAC33_OUT_AMP_CM_CTRL, 0xff);
/* 68 : LOM inverted from LOP */
dac33_write(codec, DAC33_OUT_AMP_CTRL, (3<<2));
dac33_write(codec, DAC33_PWR_CTRL, DAC33_PDNALLB);
/* Restore only selected registers (gains mostly) */
dac33_write(codec, DAC33_LDAC_DIG_VOL_CTRL,
dac33_read_reg_cache(codec, DAC33_LDAC_DIG_VOL_CTRL));
dac33_write(codec, DAC33_RDAC_DIG_VOL_CTRL,
dac33_read_reg_cache(codec, DAC33_RDAC_DIG_VOL_CTRL));
dac33_write(codec, DAC33_LINEL_TO_LLO_VOL,
dac33_read_reg_cache(codec, DAC33_LINEL_TO_LLO_VOL));
dac33_write(codec, DAC33_LINER_TO_RLO_VOL,
dac33_read_reg_cache(codec, DAC33_LINER_TO_RLO_VOL));
}
static inline void dac33_soft_power(struct snd_soc_codec *codec, int power)
{
u8 reg;
reg = dac33_read_reg_cache(codec, DAC33_PWR_CTRL);
if (power)
reg |= DAC33_PDNALLB;
else
reg &= ~(DAC33_PDNALLB | DAC33_OSCPDNB |
DAC33_DACRPDNB | DAC33_DACLPDNB);
dac33_write(codec, DAC33_PWR_CTRL, reg);
}
static int dac33_hard_power(struct snd_soc_codec *codec, int power)
{
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
int ret;
mutex_lock(&dac33->mutex);
if (power) {
ret = regulator_bulk_enable(ARRAY_SIZE(dac33->supplies),
dac33->supplies);
if (ret != 0) {
dev_err(codec->dev,
"Failed to enable supplies: %d\n", ret);
goto exit;
}
if (dac33->power_gpio >= 0)
gpio_set_value(dac33->power_gpio, 1);
dac33->chip_power = 1;
dac33_init_chip(codec);
dac33_soft_power(codec, 1);
} else {
dac33_soft_power(codec, 0);
if (dac33->power_gpio >= 0)
gpio_set_value(dac33->power_gpio, 0);
ret = regulator_bulk_disable(ARRAY_SIZE(dac33->supplies),
dac33->supplies);
if (ret != 0) {
dev_err(codec->dev,
"Failed to disable supplies: %d\n", ret);
goto exit;
}
dac33->chip_power = 0;
}
exit:
mutex_unlock(&dac33->mutex);
return ret;
}
static int dac33_get_nsample(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
ucontrol->value.integer.value[0] = dac33->nsample;
return 0;
}
static int dac33_set_nsample(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
int ret = 0;
if (dac33->nsample == ucontrol->value.integer.value[0])
return 0;
if (ucontrol->value.integer.value[0] < dac33->nsample_min ||
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
ucontrol->value.integer.value[0] > dac33->nsample_max) {
ret = -EINVAL;
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
} else {
dac33->nsample = ucontrol->value.integer.value[0];
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
/* Re calculate the burst time */
dac33->mode1_us_burst = SAMPLES_TO_US(dac33->burst_rate,
dac33->nsample);
}
return ret;
}
static int dac33_get_fifo_mode(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
ucontrol->value.integer.value[0] = dac33->fifo_mode;
return 0;
}
static int dac33_set_fifo_mode(struct snd_kcontrol *kcontrol,
struct snd_ctl_elem_value *ucontrol)
{
struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
int ret = 0;
if (dac33->fifo_mode == ucontrol->value.integer.value[0])
return 0;
/* Do not allow changes while stream is running*/
if (codec->active)
return -EPERM;
if (ucontrol->value.integer.value[0] < 0 ||
ucontrol->value.integer.value[0] >= DAC33_FIFO_LAST_MODE)
ret = -EINVAL;
else
dac33->fifo_mode = ucontrol->value.integer.value[0];
return ret;
}
/* Codec operation modes */
static const char *dac33_fifo_mode_texts[] = {
"Bypass", "Mode 1", "Mode 7"
};
static const struct soc_enum dac33_fifo_mode_enum =
SOC_ENUM_SINGLE_EXT(ARRAY_SIZE(dac33_fifo_mode_texts),
dac33_fifo_mode_texts);
/*
* DACL/R digital volume control:
* from 0 dB to -63.5 in 0.5 dB steps
* Need to be inverted later on:
* 0x00 == 0 dB
* 0x7f == -63.5 dB
*/
static DECLARE_TLV_DB_SCALE(dac_digivol_tlv, -6350, 50, 0);
static const struct snd_kcontrol_new dac33_snd_controls[] = {
SOC_DOUBLE_R_TLV("DAC Digital Playback Volume",
DAC33_LDAC_DIG_VOL_CTRL, DAC33_RDAC_DIG_VOL_CTRL,
0, 0x7f, 1, dac_digivol_tlv),
SOC_DOUBLE_R("DAC Digital Playback Switch",
DAC33_LDAC_DIG_VOL_CTRL, DAC33_RDAC_DIG_VOL_CTRL, 7, 1, 1),
SOC_DOUBLE_R("Line to Line Out Volume",
DAC33_LINEL_TO_LLO_VOL, DAC33_LINER_TO_RLO_VOL, 0, 127, 1),
};
static const struct snd_kcontrol_new dac33_nsample_snd_controls[] = {
SOC_SINGLE_EXT("nSample", 0, 0, 5900, 0,
dac33_get_nsample, dac33_set_nsample),
SOC_ENUM_EXT("FIFO Mode", dac33_fifo_mode_enum,
dac33_get_fifo_mode, dac33_set_fifo_mode),
};
/* Analog bypass */
static const struct snd_kcontrol_new dac33_dapm_abypassl_control =
SOC_DAPM_SINGLE("Switch", DAC33_LINEL_TO_LLO_VOL, 7, 1, 1);
static const struct snd_kcontrol_new dac33_dapm_abypassr_control =
SOC_DAPM_SINGLE("Switch", DAC33_LINER_TO_RLO_VOL, 7, 1, 1);
static const struct snd_soc_dapm_widget dac33_dapm_widgets[] = {
SND_SOC_DAPM_OUTPUT("LEFT_LO"),
SND_SOC_DAPM_OUTPUT("RIGHT_LO"),
SND_SOC_DAPM_INPUT("LINEL"),
SND_SOC_DAPM_INPUT("LINER"),
SND_SOC_DAPM_DAC("DACL", "Left Playback", DAC33_LDAC_PWR_CTRL, 2, 0),
SND_SOC_DAPM_DAC("DACR", "Right Playback", DAC33_RDAC_PWR_CTRL, 2, 0),
/* Analog bypass */
SND_SOC_DAPM_SWITCH("Analog Left Bypass", SND_SOC_NOPM, 0, 0,
&dac33_dapm_abypassl_control),
SND_SOC_DAPM_SWITCH("Analog Right Bypass", SND_SOC_NOPM, 0, 0,
&dac33_dapm_abypassr_control),
SND_SOC_DAPM_REG(snd_soc_dapm_mixer, "Output Left Amp Power",
DAC33_OUT_AMP_PWR_CTRL, 6, 3, 3, 0),
SND_SOC_DAPM_REG(snd_soc_dapm_mixer, "Output Right Amp Power",
DAC33_OUT_AMP_PWR_CTRL, 4, 3, 3, 0),
};
static const struct snd_soc_dapm_route audio_map[] = {
/* Analog bypass */
{"Analog Left Bypass", "Switch", "LINEL"},
{"Analog Right Bypass", "Switch", "LINER"},
{"Output Left Amp Power", NULL, "DACL"},
{"Output Right Amp Power", NULL, "DACR"},
{"Output Left Amp Power", NULL, "Analog Left Bypass"},
{"Output Right Amp Power", NULL, "Analog Right Bypass"},
/* output */
{"LEFT_LO", NULL, "Output Left Amp Power"},
{"RIGHT_LO", NULL, "Output Right Amp Power"},
};
static int dac33_add_widgets(struct snd_soc_codec *codec)
{
snd_soc_dapm_new_controls(codec, dac33_dapm_widgets,
ARRAY_SIZE(dac33_dapm_widgets));
/* set up audio path interconnects */
snd_soc_dapm_add_routes(codec, audio_map, ARRAY_SIZE(audio_map));
return 0;
}
static int dac33_set_bias_level(struct snd_soc_codec *codec,
enum snd_soc_bias_level level)
{
int ret;
switch (level) {
case SND_SOC_BIAS_ON:
dac33_soft_power(codec, 1);
break;
case SND_SOC_BIAS_PREPARE:
break;
case SND_SOC_BIAS_STANDBY:
if (codec->bias_level == SND_SOC_BIAS_OFF) {
ret = dac33_hard_power(codec, 1);
if (ret != 0)
return ret;
}
dac33_soft_power(codec, 0);
break;
case SND_SOC_BIAS_OFF:
ret = dac33_hard_power(codec, 0);
if (ret != 0)
return ret;
break;
}
codec->bias_level = level;
return 0;
}
static inline void dac33_prefill_handler(struct tlv320dac33_priv *dac33)
{
struct snd_soc_codec *codec;
codec = &dac33->codec;
switch (dac33->fifo_mode) {
case DAC33_FIFO_MODE1:
dac33_write16(codec, DAC33_NSAMPLE_MSB,
DAC33_THRREG(dac33->nsample + dac33->alarm_threshold));
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
/* Take the timestamps */
spin_lock_irq(&dac33->lock);
dac33->t_stamp2 = ktime_to_us(ktime_get());
dac33->t_stamp1 = dac33->t_stamp2;
spin_unlock_irq(&dac33->lock);
dac33_write16(codec, DAC33_PREFILL_MSB,
DAC33_THRREG(dac33->alarm_threshold));
/* Enable Alarm Threshold IRQ with a delay */
udelay(SAMPLES_TO_US(dac33->burst_rate,
dac33->alarm_threshold));
dac33_write(codec, DAC33_FIFO_IRQ_MASK, DAC33_MAT);
break;
case DAC33_FIFO_MODE7:
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
/* Take the timestamp */
spin_lock_irq(&dac33->lock);
dac33->t_stamp1 = ktime_to_us(ktime_get());
/* Move back the timestamp with drain time */
dac33->t_stamp1 -= dac33->mode7_us_to_lthr;
spin_unlock_irq(&dac33->lock);
dac33_write16(codec, DAC33_PREFILL_MSB,
DAC33_THRREG(MODE7_LTHR));
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
/* Enable Upper Threshold IRQ */
dac33_write(codec, DAC33_FIFO_IRQ_MASK, DAC33_MUT);
break;
default:
dev_warn(codec->dev, "Unhandled FIFO mode: %d\n",
dac33->fifo_mode);
break;
}
}
static inline void dac33_playback_handler(struct tlv320dac33_priv *dac33)
{
struct snd_soc_codec *codec;
codec = &dac33->codec;
switch (dac33->fifo_mode) {
case DAC33_FIFO_MODE1:
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
/* Take the timestamp */
spin_lock_irq(&dac33->lock);
dac33->t_stamp2 = ktime_to_us(ktime_get());
spin_unlock_irq(&dac33->lock);
dac33_write16(codec, DAC33_NSAMPLE_MSB,
DAC33_THRREG(dac33->nsample));
break;
case DAC33_FIFO_MODE7:
/* At the moment we are not using interrupts in mode7 */
break;
default:
dev_warn(codec->dev, "Unhandled FIFO mode: %d\n",
dac33->fifo_mode);
break;
}
}
static void dac33_work(struct work_struct *work)
{
struct snd_soc_codec *codec;
struct tlv320dac33_priv *dac33;
u8 reg;
dac33 = container_of(work, struct tlv320dac33_priv, work);
codec = &dac33->codec;
mutex_lock(&dac33->mutex);
switch (dac33->state) {
case DAC33_PREFILL:
dac33->state = DAC33_PLAYBACK;
dac33_prefill_handler(dac33);
break;
case DAC33_PLAYBACK:
dac33_playback_handler(dac33);
break;
case DAC33_IDLE:
break;
case DAC33_FLUSH:
dac33->state = DAC33_IDLE;
/* Mask all interrupts from dac33 */
dac33_write(codec, DAC33_FIFO_IRQ_MASK, 0);
/* flush fifo */
reg = dac33_read_reg_cache(codec, DAC33_FIFO_CTRL_A);
reg |= DAC33_FIFOFLUSH;
dac33_write(codec, DAC33_FIFO_CTRL_A, reg);
break;
}
mutex_unlock(&dac33->mutex);
}
static irqreturn_t dac33_interrupt_handler(int irq, void *dev)
{
struct snd_soc_codec *codec = dev;
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
spin_lock(&dac33->lock);
dac33->t_stamp1 = ktime_to_us(ktime_get());
spin_unlock(&dac33->lock);
/* Do not schedule the workqueue in Mode7 */
if (dac33->fifo_mode != DAC33_FIFO_MODE7)
queue_work(dac33->dac33_wq, &dac33->work);
return IRQ_HANDLED;
}
static void dac33_oscwait(struct snd_soc_codec *codec)
{
int timeout = 20;
u8 reg;
do {
msleep(1);
dac33_read(codec, DAC33_INT_OSC_STATUS, &reg);
} while (((reg & 0x03) != DAC33_OSCSTATUS_NORMAL) && timeout--);
if ((reg & 0x03) != DAC33_OSCSTATUS_NORMAL)
dev_err(codec->dev,
"internal oscillator calibration failed\n");
}
static int dac33_hw_params(struct snd_pcm_substream *substream,
struct snd_pcm_hw_params *params,
struct snd_soc_dai *dai)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_device *socdev = rtd->socdev;
struct snd_soc_codec *codec = socdev->card->codec;
/* Check parameters for validity */
switch (params_rate(params)) {
case 44100:
case 48000:
break;
default:
dev_err(codec->dev, "unsupported rate %d\n",
params_rate(params));
return -EINVAL;
}
switch (params_format(params)) {
case SNDRV_PCM_FORMAT_S16_LE:
break;
default:
dev_err(codec->dev, "unsupported format %d\n",
params_format(params));
return -EINVAL;
}
return 0;
}
#define CALC_OSCSET(rate, refclk) ( \
((((rate * 10000) / refclk) * 4096) + 7000) / 10000)
#define CALC_RATIOSET(rate, refclk) ( \
((((refclk * 100000) / rate) * 16384) + 50000) / 100000)
/*
* tlv320dac33 is strict on the sequence of the register writes, if the register
* writes happens in different order, than dac33 might end up in unknown state.
* Use the known, working sequence of register writes to initialize the dac33.
*/
static int dac33_prepare_chip(struct snd_pcm_substream *substream)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_device *socdev = rtd->socdev;
struct snd_soc_codec *codec = socdev->card->codec;
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
unsigned int oscset, ratioset, pwr_ctrl, reg_tmp;
u8 aictrl_a, aictrl_b, fifoctrl_a;
switch (substream->runtime->rate) {
case 44100:
case 48000:
oscset = CALC_OSCSET(substream->runtime->rate, dac33->refclk);
ratioset = CALC_RATIOSET(substream->runtime->rate,
dac33->refclk);
break;
default:
dev_err(codec->dev, "unsupported rate %d\n",
substream->runtime->rate);
return -EINVAL;
}
aictrl_a = dac33_read_reg_cache(codec, DAC33_SER_AUDIOIF_CTRL_A);
aictrl_a &= ~(DAC33_NCYCL_MASK | DAC33_WLEN_MASK);
/* Read FIFO control A, and clear FIFO flush bit */
fifoctrl_a = dac33_read_reg_cache(codec, DAC33_FIFO_CTRL_A);
fifoctrl_a &= ~DAC33_FIFOFLUSH;
fifoctrl_a &= ~DAC33_WIDTH;
switch (substream->runtime->format) {
case SNDRV_PCM_FORMAT_S16_LE:
aictrl_a |= (DAC33_NCYCL_16 | DAC33_WLEN_16);
fifoctrl_a |= DAC33_WIDTH;
break;
default:
dev_err(codec->dev, "unsupported format %d\n",
substream->runtime->format);
return -EINVAL;
}
mutex_lock(&dac33->mutex);
dac33_soft_power(codec, 0);
dac33_soft_power(codec, 1);
reg_tmp = dac33_read_reg_cache(codec, DAC33_INT_OSC_CTRL);
dac33_write(codec, DAC33_INT_OSC_CTRL, reg_tmp);
/* Write registers 0x08 and 0x09 (MSB, LSB) */
dac33_write16(codec, DAC33_INT_OSC_FREQ_RAT_A, oscset);
/* calib time: 128 is a nice number ;) */
dac33_write(codec, DAC33_CALIB_TIME, 128);
/* adjustment treshold & step */
dac33_write(codec, DAC33_INT_OSC_CTRL_B, DAC33_ADJTHRSHLD(2) |
DAC33_ADJSTEP(1));
/* div=4 / gain=1 / div */
dac33_write(codec, DAC33_INT_OSC_CTRL_C, DAC33_REFDIV(4));
pwr_ctrl = dac33_read_reg_cache(codec, DAC33_PWR_CTRL);
pwr_ctrl |= DAC33_OSCPDNB | DAC33_DACRPDNB | DAC33_DACLPDNB;
dac33_write(codec, DAC33_PWR_CTRL, pwr_ctrl);
dac33_oscwait(codec);
if (dac33->fifo_mode) {
/* Generic for all FIFO modes */
/* 50-51 : ASRC Control registers */
dac33_write(codec, DAC33_ASRC_CTRL_A, DAC33_SRCLKDIV(1));
dac33_write(codec, DAC33_ASRC_CTRL_B, 1); /* ??? */
/* Write registers 0x34 and 0x35 (MSB, LSB) */
dac33_write16(codec, DAC33_SRC_REF_CLK_RATIO_A, ratioset);
/* Set interrupts to high active */
dac33_write(codec, DAC33_INTP_CTRL_A, DAC33_INTPM_AHIGH);
} else {
/* FIFO bypass mode */
/* 50-51 : ASRC Control registers */
dac33_write(codec, DAC33_ASRC_CTRL_A, DAC33_SRCBYP);
dac33_write(codec, DAC33_ASRC_CTRL_B, 0); /* ??? */
}
/* Interrupt behaviour configuration */
switch (dac33->fifo_mode) {
case DAC33_FIFO_MODE1:
dac33_write(codec, DAC33_FIFO_IRQ_MODE_B,
DAC33_ATM(DAC33_FIFO_IRQ_MODE_LEVEL));
break;
case DAC33_FIFO_MODE7:
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
dac33_write(codec, DAC33_FIFO_IRQ_MODE_A,
DAC33_UTM(DAC33_FIFO_IRQ_MODE_LEVEL));
break;
default:
/* in FIFO bypass mode, the interrupts are not used */
break;
}
aictrl_b = dac33_read_reg_cache(codec, DAC33_SER_AUDIOIF_CTRL_B);
switch (dac33->fifo_mode) {
case DAC33_FIFO_MODE1:
/*
* For mode1:
* Disable the FIFO bypass (Enable the use of FIFO)
* Select nSample mode
* BCLK is only running when data is needed by DAC33
*/
fifoctrl_a &= ~DAC33_FBYPAS;
fifoctrl_a &= ~DAC33_FAUTO;
if (dac33->keep_bclk)
aictrl_b |= DAC33_BCLKON;
else
aictrl_b &= ~DAC33_BCLKON;
break;
case DAC33_FIFO_MODE7:
/*
* For mode1:
* Disable the FIFO bypass (Enable the use of FIFO)
* Select Threshold mode
* BCLK is only running when data is needed by DAC33
*/
fifoctrl_a &= ~DAC33_FBYPAS;
fifoctrl_a |= DAC33_FAUTO;
if (dac33->keep_bclk)
aictrl_b |= DAC33_BCLKON;
else
aictrl_b &= ~DAC33_BCLKON;
break;
default:
/*
* For FIFO bypass mode:
* Enable the FIFO bypass (Disable the FIFO use)
* Set the BCLK as continous
*/
fifoctrl_a |= DAC33_FBYPAS;
aictrl_b |= DAC33_BCLKON;
break;
}
dac33_write(codec, DAC33_FIFO_CTRL_A, fifoctrl_a);
dac33_write(codec, DAC33_SER_AUDIOIF_CTRL_A, aictrl_a);
dac33_write(codec, DAC33_SER_AUDIOIF_CTRL_B, aictrl_b);
/*
* BCLK divide ratio
* 0: 1.5
* 1: 1
* 2: 2
* ...
* 254: 254
* 255: 255
*/
if (dac33->fifo_mode)
dac33_write(codec, DAC33_SER_AUDIOIF_CTRL_C,
dac33->burst_bclkdiv);
else
dac33_write(codec, DAC33_SER_AUDIOIF_CTRL_C, 32);
switch (dac33->fifo_mode) {
case DAC33_FIFO_MODE1:
dac33_write16(codec, DAC33_ATHR_MSB,
DAC33_THRREG(dac33->alarm_threshold));
break;
case DAC33_FIFO_MODE7:
/*
* Configure the threshold levels, and leave 10 sample space
* at the bottom, and also at the top of the FIFO
*/
dac33_write16(codec, DAC33_UTHR_MSB, DAC33_THRREG(MODE7_UTHR));
dac33_write16(codec, DAC33_LTHR_MSB, DAC33_THRREG(MODE7_LTHR));
break;
default:
break;
}
mutex_unlock(&dac33->mutex);
return 0;
}
static void dac33_calculate_times(struct snd_pcm_substream *substream)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_device *socdev = rtd->socdev;
struct snd_soc_codec *codec = socdev->card->codec;
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
unsigned int nsample_limit;
/* In bypass mode we don't need to calculate */
if (!dac33->fifo_mode)
return;
/* Number of samples (16bit, stereo) in one period */
dac33->nsample_min = snd_pcm_lib_period_bytes(substream) / 4;
/* Number of samples (16bit, stereo) in ALSA buffer */
dac33->nsample_max = snd_pcm_lib_buffer_bytes(substream) / 4;
/* Subtract one period from the total */
dac33->nsample_max -= dac33->nsample_min;
/* Number of samples for LATENCY_TIME_MS / 2 */
dac33->alarm_threshold = substream->runtime->rate /
(1000 / (LATENCY_TIME_MS / 2));
/* Find and fix up the lowest nsmaple limit */
nsample_limit = substream->runtime->rate / (1000 / LATENCY_TIME_MS);
if (dac33->nsample_min < nsample_limit)
dac33->nsample_min = nsample_limit;
if (dac33->nsample < dac33->nsample_min)
dac33->nsample = dac33->nsample_min;
/*
* Find and fix up the highest nsmaple limit
* In order to not overflow the DAC33 buffer substract the
* alarm_threshold value from the size of the DAC33 buffer
*/
nsample_limit = DAC33_BUFFER_SIZE_SAMPLES - dac33->alarm_threshold;
if (dac33->nsample_max > nsample_limit)
dac33->nsample_max = nsample_limit;
if (dac33->nsample > dac33->nsample_max)
dac33->nsample = dac33->nsample_max;
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
switch (dac33->fifo_mode) {
case DAC33_FIFO_MODE1:
dac33->mode1_us_burst = SAMPLES_TO_US(dac33->burst_rate,
dac33->nsample);
dac33->t_stamp1 = 0;
dac33->t_stamp2 = 0;
break;
case DAC33_FIFO_MODE7:
dac33->mode7_us_to_lthr =
SAMPLES_TO_US(substream->runtime->rate,
MODE7_UTHR - MODE7_LTHR + 1);
dac33->t_stamp1 = 0;
break;
default:
break;
}
}
static int dac33_pcm_prepare(struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
dac33_calculate_times(substream);
dac33_prepare_chip(substream);
return 0;
}
static int dac33_pcm_trigger(struct snd_pcm_substream *substream, int cmd,
struct snd_soc_dai *dai)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_device *socdev = rtd->socdev;
struct snd_soc_codec *codec = socdev->card->codec;
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
int ret = 0;
switch (cmd) {
case SNDRV_PCM_TRIGGER_START:
case SNDRV_PCM_TRIGGER_RESUME:
case SNDRV_PCM_TRIGGER_PAUSE_RELEASE:
if (dac33->fifo_mode) {
dac33->state = DAC33_PREFILL;
queue_work(dac33->dac33_wq, &dac33->work);
}
break;
case SNDRV_PCM_TRIGGER_STOP:
case SNDRV_PCM_TRIGGER_SUSPEND:
case SNDRV_PCM_TRIGGER_PAUSE_PUSH:
if (dac33->fifo_mode) {
dac33->state = DAC33_FLUSH;
queue_work(dac33->dac33_wq, &dac33->work);
}
break;
default:
ret = -EINVAL;
}
return ret;
}
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
static snd_pcm_sframes_t dac33_dai_delay(
struct snd_pcm_substream *substream,
struct snd_soc_dai *dai)
{
struct snd_soc_pcm_runtime *rtd = substream->private_data;
struct snd_soc_device *socdev = rtd->socdev;
struct snd_soc_codec *codec = socdev->card->codec;
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
unsigned long long t0, t1, t_now;
unsigned int time_delta;
int samples_out, samples_in, samples;
snd_pcm_sframes_t delay = 0;
switch (dac33->fifo_mode) {
case DAC33_FIFO_BYPASS:
break;
case DAC33_FIFO_MODE1:
spin_lock(&dac33->lock);
t0 = dac33->t_stamp1;
t1 = dac33->t_stamp2;
spin_unlock(&dac33->lock);
t_now = ktime_to_us(ktime_get());
/* We have not started to fill the FIFO yet, delay is 0 */
if (!t1)
goto out;
if (t0 > t1) {
/*
* Phase 1:
* After Alarm threshold, and before nSample write
*/
time_delta = t_now - t0;
samples_out = time_delta ? US_TO_SAMPLES(
substream->runtime->rate,
time_delta) : 0;
if (likely(dac33->alarm_threshold > samples_out))
delay = dac33->alarm_threshold - samples_out;
else
delay = 0;
} else if ((t_now - t1) <= dac33->mode1_us_burst) {
/*
* Phase 2:
* After nSample write (during burst operation)
*/
time_delta = t_now - t0;
samples_out = time_delta ? US_TO_SAMPLES(
substream->runtime->rate,
time_delta) : 0;
time_delta = t_now - t1;
samples_in = time_delta ? US_TO_SAMPLES(
dac33->burst_rate,
time_delta) : 0;
samples = dac33->alarm_threshold;
samples += (samples_in - samples_out);
if (likely(samples > 0))
delay = samples;
else
delay = 0;
} else {
/*
* Phase 3:
* After burst operation, before next alarm threshold
*/
time_delta = t_now - t0;
samples_out = time_delta ? US_TO_SAMPLES(
substream->runtime->rate,
time_delta) : 0;
samples_in = dac33->nsample;
samples = dac33->alarm_threshold;
samples += (samples_in - samples_out);
if (likely(samples > 0))
delay = samples > DAC33_BUFFER_SIZE_SAMPLES ?
DAC33_BUFFER_SIZE_SAMPLES : samples;
else
delay = 0;
}
break;
case DAC33_FIFO_MODE7:
spin_lock(&dac33->lock);
t0 = dac33->t_stamp1;
spin_unlock(&dac33->lock);
t_now = ktime_to_us(ktime_get());
/* We have not started to fill the FIFO yet, delay is 0 */
if (!t0)
goto out;
if (t_now <= t0) {
/*
* Either the timestamps are messed or equal. Report
* maximum delay
*/
delay = MODE7_UTHR;
goto out;
}
time_delta = t_now - t0;
if (time_delta <= dac33->mode7_us_to_lthr) {
/*
* Phase 1:
* After burst (draining phase)
*/
samples_out = US_TO_SAMPLES(
substream->runtime->rate,
time_delta);
if (likely(MODE7_UTHR > samples_out))
delay = MODE7_UTHR - samples_out;
else
delay = 0;
} else {
/*
* Phase 2:
* During burst operation
*/
time_delta = time_delta - dac33->mode7_us_to_lthr;
samples_out = US_TO_SAMPLES(
substream->runtime->rate,
time_delta);
samples_in = US_TO_SAMPLES(
dac33->burst_rate,
time_delta);
delay = MODE7_LTHR + samples_in - samples_out;
if (unlikely(delay > MODE7_UTHR))
delay = MODE7_UTHR;
}
break;
default:
dev_warn(codec->dev, "Unhandled FIFO mode: %d\n",
dac33->fifo_mode);
break;
}
out:
return delay;
}
static int dac33_set_dai_sysclk(struct snd_soc_dai *codec_dai,
int clk_id, unsigned int freq, int dir)
{
struct snd_soc_codec *codec = codec_dai->codec;
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
u8 ioc_reg, asrcb_reg;
ioc_reg = dac33_read_reg_cache(codec, DAC33_INT_OSC_CTRL);
asrcb_reg = dac33_read_reg_cache(codec, DAC33_ASRC_CTRL_B);
switch (clk_id) {
case TLV320DAC33_MCLK:
ioc_reg |= DAC33_REFSEL;
asrcb_reg |= DAC33_SRCREFSEL;
break;
case TLV320DAC33_SLEEPCLK:
ioc_reg &= ~DAC33_REFSEL;
asrcb_reg &= ~DAC33_SRCREFSEL;
break;
default:
dev_err(codec->dev, "Invalid clock ID (%d)\n", clk_id);
break;
}
dac33->refclk = freq;
dac33_write_reg_cache(codec, DAC33_INT_OSC_CTRL, ioc_reg);
dac33_write_reg_cache(codec, DAC33_ASRC_CTRL_B, asrcb_reg);
return 0;
}
static int dac33_set_dai_fmt(struct snd_soc_dai *codec_dai,
unsigned int fmt)
{
struct snd_soc_codec *codec = codec_dai->codec;
struct tlv320dac33_priv *dac33 = snd_soc_codec_get_drvdata(codec);
u8 aictrl_a, aictrl_b;
aictrl_a = dac33_read_reg_cache(codec, DAC33_SER_AUDIOIF_CTRL_A);
aictrl_b = dac33_read_reg_cache(codec, DAC33_SER_AUDIOIF_CTRL_B);
/* set master/slave audio interface */
switch (fmt & SND_SOC_DAIFMT_MASTER_MASK) {
case SND_SOC_DAIFMT_CBM_CFM:
/* Codec Master */
aictrl_a |= (DAC33_MSBCLK | DAC33_MSWCLK);
break;
case SND_SOC_DAIFMT_CBS_CFS:
/* Codec Slave */
if (dac33->fifo_mode) {
dev_err(codec->dev, "FIFO mode requires master mode\n");
return -EINVAL;
} else
aictrl_a &= ~(DAC33_MSBCLK | DAC33_MSWCLK);
break;
default:
return -EINVAL;
}
aictrl_a &= ~DAC33_AFMT_MASK;
switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) {
case SND_SOC_DAIFMT_I2S:
aictrl_a |= DAC33_AFMT_I2S;
break;
case SND_SOC_DAIFMT_DSP_A:
aictrl_a |= DAC33_AFMT_DSP;
aictrl_b &= ~DAC33_DATA_DELAY_MASK;
aictrl_b |= DAC33_DATA_DELAY(0);
break;
case SND_SOC_DAIFMT_RIGHT_J:
aictrl_a |= DAC33_AFMT_RIGHT_J;
break;
case SND_SOC_DAIFMT_LEFT_J:
aictrl_a |= DAC33_AFMT_LEFT_J;
break;
default:
dev_err(codec->dev, "Unsupported format (%u)\n",
fmt & SND_SOC_DAIFMT_FORMAT_MASK);
return -EINVAL;
}
dac33_write_reg_cache(codec, DAC33_SER_AUDIOIF_CTRL_A, aictrl_a);
dac33_write_reg_cache(codec, DAC33_SER_AUDIOIF_CTRL_B, aictrl_b);
return 0;
}
static int dac33_soc_probe(struct platform_device *pdev)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
struct snd_soc_codec *codec;
struct tlv320dac33_priv *dac33;
int ret = 0;
BUG_ON(!tlv320dac33_codec);
codec = tlv320dac33_codec;
socdev->card->codec = codec;
dac33 = snd_soc_codec_get_drvdata(codec);
/* Power up the codec */
dac33_hard_power(codec, 1);
/* register pcms */
ret = snd_soc_new_pcms(socdev, SNDRV_DEFAULT_IDX1, SNDRV_DEFAULT_STR1);
if (ret < 0) {
dev_err(codec->dev, "failed to create pcms\n");
goto pcm_err;
}
snd_soc_add_controls(codec, dac33_snd_controls,
ARRAY_SIZE(dac33_snd_controls));
/* Only add the nSample controls, if we have valid IRQ number */
if (dac33->irq >= 0)
snd_soc_add_controls(codec, dac33_nsample_snd_controls,
ARRAY_SIZE(dac33_nsample_snd_controls));
dac33_add_widgets(codec);
/* power on device */
dac33_set_bias_level(codec, SND_SOC_BIAS_STANDBY);
/* Bias level configuration has enabled regulator an extra time */
regulator_bulk_disable(ARRAY_SIZE(dac33->supplies), dac33->supplies);
return 0;
pcm_err:
dac33_hard_power(codec, 0);
return ret;
}
static int dac33_soc_remove(struct platform_device *pdev)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
struct snd_soc_codec *codec = socdev->card->codec;
dac33_set_bias_level(codec, SND_SOC_BIAS_OFF);
snd_soc_free_pcms(socdev);
snd_soc_dapm_free(socdev);
return 0;
}
static int dac33_soc_suspend(struct platform_device *pdev, pm_message_t state)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
struct snd_soc_codec *codec = socdev->card->codec;
dac33_set_bias_level(codec, SND_SOC_BIAS_OFF);
return 0;
}
static int dac33_soc_resume(struct platform_device *pdev)
{
struct snd_soc_device *socdev = platform_get_drvdata(pdev);
struct snd_soc_codec *codec = socdev->card->codec;
dac33_set_bias_level(codec, SND_SOC_BIAS_STANDBY);
dac33_set_bias_level(codec, codec->suspend_bias_level);
return 0;
}
struct snd_soc_codec_device soc_codec_dev_tlv320dac33 = {
.probe = dac33_soc_probe,
.remove = dac33_soc_remove,
.suspend = dac33_soc_suspend,
.resume = dac33_soc_resume,
};
EXPORT_SYMBOL_GPL(soc_codec_dev_tlv320dac33);
#define DAC33_RATES (SNDRV_PCM_RATE_44100 | \
SNDRV_PCM_RATE_48000)
#define DAC33_FORMATS SNDRV_PCM_FMTBIT_S16_LE
static struct snd_soc_dai_ops dac33_dai_ops = {
.hw_params = dac33_hw_params,
.prepare = dac33_pcm_prepare,
.trigger = dac33_pcm_trigger,
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
.delay = dac33_dai_delay,
.set_sysclk = dac33_set_dai_sysclk,
.set_fmt = dac33_set_dai_fmt,
};
struct snd_soc_dai dac33_dai = {
.name = "tlv320dac33",
.playback = {
.stream_name = "Playback",
.channels_min = 2,
.channels_max = 2,
.rates = DAC33_RATES,
.formats = DAC33_FORMATS,},
.ops = &dac33_dai_ops,
};
EXPORT_SYMBOL_GPL(dac33_dai);
static int __devinit dac33_i2c_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct tlv320dac33_platform_data *pdata;
struct tlv320dac33_priv *dac33;
struct snd_soc_codec *codec;
int ret, i;
if (client->dev.platform_data == NULL) {
dev_err(&client->dev, "Platform data not set\n");
return -ENODEV;
}
pdata = client->dev.platform_data;
dac33 = kzalloc(sizeof(struct tlv320dac33_priv), GFP_KERNEL);
if (dac33 == NULL)
return -ENOMEM;
codec = &dac33->codec;
snd_soc_codec_set_drvdata(codec, dac33);
codec->control_data = client;
mutex_init(&codec->mutex);
mutex_init(&dac33->mutex);
ASoC: tlv320dac33: FIFO caused delay reporting Delay reporting for the three implemented DAC33 FIFO modes. DAC33 has FIFO depth status register(s), but it can not be used, since inside of pcm_pointer we can not send I2C commands. Timestamp based estimation need to be used. The method of calculating the delay depends on the active FIFO mode. Bypass mode: FIFO is bypassed, report 0 as delay Mode1: nSample fill mode. In this mode I need to use two timestamp ts1: taken when the interrupt has been received ts2: taken before writing to nSample register. Interrupts are coming when DAC33 FIFO depth goes under alarm threshold. Phase1: when we received the alarm threshold, but our workqueue has not been executed (safeguard phase). Just count the played out samples since ts1 and subtract it from the alarm threshold value. Phase2: During nSample burst (after writing to nSample register), count the played out samples since ts1, count the samples received since ts2 (in a burst). Estimate the FIFO depth using these and alarm threshold value. Phase3: Draining phase (after the burst read), count the played out samples since ts1. Estimate the FIFO depth using the nSample configuration and the alarm threshold value. Mode7: Threshold based fill mode. In this mode one timestamp is enough. ts1: taken when the interrupt has been received Interrupts are coming when DAC33 FIFO depth reaches upper threshold. Phase1: Draining phase (after the burst), counting the played out samples since ts1, and subtract it from the upper threshold value. Phase2: During burst operation. Using the pre calculated time needed to play out samples from the buffer during the drain period (from upper to lower threshold), move the time window to cover the estimated time from the burst start to the current time. Calculate the samples played out since lower threshold and also the samples received during the same time. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-04-23 07:10:01 +00:00
spin_lock_init(&dac33->lock);
INIT_LIST_HEAD(&codec->dapm_widgets);
INIT_LIST_HEAD(&codec->dapm_paths);
codec->name = "tlv320dac33";
codec->owner = THIS_MODULE;
codec->read = dac33_read_reg_cache;
codec->write = dac33_write_locked;
codec->hw_write = (hw_write_t) i2c_master_send;
codec->bias_level = SND_SOC_BIAS_OFF;
codec->set_bias_level = dac33_set_bias_level;
codec->dai = &dac33_dai;
codec->num_dai = 1;
codec->reg_cache_size = ARRAY_SIZE(dac33_reg);
codec->reg_cache = kmemdup(dac33_reg, ARRAY_SIZE(dac33_reg),
GFP_KERNEL);
if (codec->reg_cache == NULL) {
ret = -ENOMEM;
goto error_reg;
}
i2c_set_clientdata(client, dac33);
dac33->power_gpio = pdata->power_gpio;
dac33->burst_bclkdiv = pdata->burst_bclkdiv;
/* Pre calculate the burst rate */
dac33->burst_rate = BURST_BASEFREQ_HZ / dac33->burst_bclkdiv / 32;
dac33->keep_bclk = pdata->keep_bclk;
dac33->irq = client->irq;
dac33->nsample = NSAMPLE_MAX;
dac33->nsample_max = NSAMPLE_MAX;
/* Disable FIFO use by default */
dac33->fifo_mode = DAC33_FIFO_BYPASS;
tlv320dac33_codec = codec;
codec->dev = &client->dev;
dac33_dai.dev = codec->dev;
/* Check if the reset GPIO number is valid and request it */
if (dac33->power_gpio >= 0) {
ret = gpio_request(dac33->power_gpio, "tlv320dac33 reset");
if (ret < 0) {
dev_err(codec->dev,
"Failed to request reset GPIO (%d)\n",
dac33->power_gpio);
snd_soc_unregister_dai(&dac33_dai);
snd_soc_unregister_codec(codec);
goto error_gpio;
}
gpio_direction_output(dac33->power_gpio, 0);
} else {
dac33->chip_power = 1;
}
/* Check if the IRQ number is valid and request it */
if (dac33->irq >= 0) {
ret = request_irq(dac33->irq, dac33_interrupt_handler,
IRQF_TRIGGER_RISING | IRQF_DISABLED,
codec->name, codec);
if (ret < 0) {
dev_err(codec->dev, "Could not request IRQ%d (%d)\n",
dac33->irq, ret);
dac33->irq = -1;
}
if (dac33->irq != -1) {
/* Setup work queue */
dac33->dac33_wq =
create_singlethread_workqueue("tlv320dac33");
if (dac33->dac33_wq == NULL) {
free_irq(dac33->irq, &dac33->codec);
ret = -ENOMEM;
goto error_wq;
}
INIT_WORK(&dac33->work, dac33_work);
}
}
for (i = 0; i < ARRAY_SIZE(dac33->supplies); i++)
dac33->supplies[i].supply = dac33_supply_names[i];
ret = regulator_bulk_get(codec->dev, ARRAY_SIZE(dac33->supplies),
dac33->supplies);
if (ret != 0) {
dev_err(codec->dev, "Failed to request supplies: %d\n", ret);
goto err_get;
}
ret = regulator_bulk_enable(ARRAY_SIZE(dac33->supplies),
dac33->supplies);
if (ret != 0) {
dev_err(codec->dev, "Failed to enable supplies: %d\n", ret);
goto err_enable;
}
ret = snd_soc_register_codec(codec);
if (ret != 0) {
dev_err(codec->dev, "Failed to register codec: %d\n", ret);
goto error_codec;
}
ret = snd_soc_register_dai(&dac33_dai);
if (ret != 0) {
dev_err(codec->dev, "Failed to register DAI: %d\n", ret);
snd_soc_unregister_codec(codec);
goto error_codec;
}
/* Shut down the codec for now */
dac33_hard_power(codec, 0);
return ret;
error_codec:
regulator_bulk_disable(ARRAY_SIZE(dac33->supplies), dac33->supplies);
err_enable:
regulator_bulk_free(ARRAY_SIZE(dac33->supplies), dac33->supplies);
err_get:
if (dac33->irq >= 0) {
free_irq(dac33->irq, &dac33->codec);
destroy_workqueue(dac33->dac33_wq);
}
error_wq:
if (dac33->power_gpio >= 0)
gpio_free(dac33->power_gpio);
error_gpio:
kfree(codec->reg_cache);
error_reg:
tlv320dac33_codec = NULL;
kfree(dac33);
return ret;
}
static int __devexit dac33_i2c_remove(struct i2c_client *client)
{
struct tlv320dac33_priv *dac33;
dac33 = i2c_get_clientdata(client);
dac33_hard_power(&dac33->codec, 0);
if (dac33->power_gpio >= 0)
gpio_free(dac33->power_gpio);
if (dac33->irq >= 0)
free_irq(dac33->irq, &dac33->codec);
regulator_bulk_disable(ARRAY_SIZE(dac33->supplies), dac33->supplies);
regulator_bulk_free(ARRAY_SIZE(dac33->supplies), dac33->supplies);
destroy_workqueue(dac33->dac33_wq);
snd_soc_unregister_dai(&dac33_dai);
snd_soc_unregister_codec(&dac33->codec);
kfree(dac33->codec.reg_cache);
kfree(dac33);
tlv320dac33_codec = NULL;
return 0;
}
static const struct i2c_device_id tlv320dac33_i2c_id[] = {
{
.name = "tlv320dac33",
.driver_data = 0,
},
{ },
};
static struct i2c_driver tlv320dac33_i2c_driver = {
.driver = {
.name = "tlv320dac33",
.owner = THIS_MODULE,
},
.probe = dac33_i2c_probe,
.remove = __devexit_p(dac33_i2c_remove),
.id_table = tlv320dac33_i2c_id,
};
static int __init dac33_module_init(void)
{
int r;
r = i2c_add_driver(&tlv320dac33_i2c_driver);
if (r < 0) {
printk(KERN_ERR "DAC33: driver registration failed\n");
return r;
}
return 0;
}
module_init(dac33_module_init);
static void __exit dac33_module_exit(void)
{
i2c_del_driver(&tlv320dac33_i2c_driver);
}
module_exit(dac33_module_exit);
MODULE_DESCRIPTION("ASoC TLV320DAC33 codec driver");
MODULE_AUTHOR("Peter Ujfalusi <peter.ujfalusi@nokia.com>");
MODULE_LICENSE("GPL");