linux/drivers/usb/host/xhci-ring.c

3568 lines
110 KiB
C
Raw Normal View History

/*
* xHCI host controller driver
*
* Copyright (C) 2008 Intel Corp.
*
* Author: Sarah Sharp
* Some code borrowed from the Linux EHCI driver.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
/*
* Ring initialization rules:
* 1. Each segment is initialized to zero, except for link TRBs.
* 2. Ring cycle state = 0. This represents Producer Cycle State (PCS) or
* Consumer Cycle State (CCS), depending on ring function.
* 3. Enqueue pointer = dequeue pointer = address of first TRB in the segment.
*
* Ring behavior rules:
* 1. A ring is empty if enqueue == dequeue. This means there will always be at
* least one free TRB in the ring. This is useful if you want to turn that
* into a link TRB and expand the ring.
* 2. When incrementing an enqueue or dequeue pointer, if the next TRB is a
* link TRB, then load the pointer with the address in the link TRB. If the
* link TRB had its toggle bit set, you may need to update the ring cycle
* state (see cycle bit rules). You may have to do this multiple times
* until you reach a non-link TRB.
* 3. A ring is full if enqueue++ (for the definition of increment above)
* equals the dequeue pointer.
*
* Cycle bit rules:
* 1. When a consumer increments a dequeue pointer and encounters a toggle bit
* in a link TRB, it must toggle the ring cycle state.
* 2. When a producer increments an enqueue pointer and encounters a toggle bit
* in a link TRB, it must toggle the ring cycle state.
*
* Producer rules:
* 1. Check if ring is full before you enqueue.
* 2. Write the ring cycle state to the cycle bit in the TRB you're enqueuing.
* Update enqueue pointer between each write (which may update the ring
* cycle state).
* 3. Notify consumer. If SW is producer, it rings the doorbell for command
* and endpoint rings. If HC is the producer for the event ring,
* and it generates an interrupt according to interrupt modulation rules.
*
* Consumer rules:
* 1. Check if TRB belongs to you. If the cycle bit == your ring cycle state,
* the TRB is owned by the consumer.
* 2. Update dequeue pointer (which may update the ring cycle state) and
* continue processing TRBs until you reach a TRB which is not owned by you.
* 3. Notify the producer. SW is the consumer for the event ring, and it
* updates event ring dequeue pointer. HC is the consumer for the command and
* endpoint rings; it generates events on the event ring for these.
*/
#include <linux/scatterlist.h>
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-03-24 08:04:11 +00:00
#include <linux/slab.h>
#include "xhci.h"
static int handle_cmd_in_cmd_wait_list(struct xhci_hcd *xhci,
struct xhci_virt_device *virt_dev,
struct xhci_event_cmd *event);
/*
* Returns zero if the TRB isn't in this segment, otherwise it returns the DMA
* address of the TRB.
*/
dma_addr_t xhci_trb_virt_to_dma(struct xhci_segment *seg,
union xhci_trb *trb)
{
unsigned long segment_offset;
if (!seg || !trb || trb < seg->trbs)
return 0;
/* offset in TRBs */
segment_offset = trb - seg->trbs;
if (segment_offset > TRBS_PER_SEGMENT)
return 0;
return seg->dma + (segment_offset * sizeof(*trb));
}
/* Does this link TRB point to the first segment in a ring,
* or was the previous TRB the last TRB on the last segment in the ERST?
*/
static bool last_trb_on_last_seg(struct xhci_hcd *xhci, struct xhci_ring *ring,
struct xhci_segment *seg, union xhci_trb *trb)
{
if (ring == xhci->event_ring)
return (trb == &seg->trbs[TRBS_PER_SEGMENT]) &&
(seg->next == xhci->event_ring->first_seg);
else
return le32_to_cpu(trb->link.control) & LINK_TOGGLE;
}
/* Is this TRB a link TRB or was the last TRB the last TRB in this event ring
* segment? I.e. would the updated event TRB pointer step off the end of the
* event seg?
*/
static int last_trb(struct xhci_hcd *xhci, struct xhci_ring *ring,
struct xhci_segment *seg, union xhci_trb *trb)
{
if (ring == xhci->event_ring)
return trb == &seg->trbs[TRBS_PER_SEGMENT];
else
return (le32_to_cpu(trb->link.control) & TRB_TYPE_BITMASK)
== TRB_TYPE(TRB_LINK);
}
static int enqueue_is_link_trb(struct xhci_ring *ring)
{
struct xhci_link_trb *link = &ring->enqueue->link;
return ((le32_to_cpu(link->control) & TRB_TYPE_BITMASK) ==
TRB_TYPE(TRB_LINK));
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* Updates trb to point to the next TRB in the ring, and updates seg if the next
* TRB is in a new segment. This does not skip over link TRBs, and it does not
* effect the ring dequeue or enqueue pointers.
*/
static void next_trb(struct xhci_hcd *xhci,
struct xhci_ring *ring,
struct xhci_segment **seg,
union xhci_trb **trb)
{
if (last_trb(xhci, ring, *seg, *trb)) {
*seg = (*seg)->next;
*trb = ((*seg)->trbs);
} else {
(*trb)++;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
}
/*
* See Cycle bit rules. SW is the consumer for the event ring only.
* Don't make a ring full of link TRBs. That would be dumb and this would loop.
*/
static void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring, bool consumer)
{
union xhci_trb *next = ++(ring->dequeue);
unsigned long long addr;
ring->deq_updates++;
/* Update the dequeue pointer further if that was a link TRB or we're at
* the end of an event ring segment (which doesn't have link TRBS)
*/
while (last_trb(xhci, ring, ring->deq_seg, next)) {
if (consumer && last_trb_on_last_seg(xhci, ring, ring->deq_seg, next)) {
ring->cycle_state = (ring->cycle_state ? 0 : 1);
if (!in_interrupt())
xhci_dbg(xhci, "Toggle cycle state for ring %p = %i\n",
ring,
(unsigned int) ring->cycle_state);
}
ring->deq_seg = ring->deq_seg->next;
ring->dequeue = ring->deq_seg->trbs;
next = ring->dequeue;
}
addr = (unsigned long long) xhci_trb_virt_to_dma(ring->deq_seg, ring->dequeue);
if (ring == xhci->event_ring)
xhci_dbg(xhci, "Event ring deq = 0x%llx (DMA)\n", addr);
else if (ring == xhci->cmd_ring)
xhci_dbg(xhci, "Command ring deq = 0x%llx (DMA)\n", addr);
else
xhci_dbg(xhci, "Ring deq = 0x%llx (DMA)\n", addr);
}
/*
* See Cycle bit rules. SW is the consumer for the event ring only.
* Don't make a ring full of link TRBs. That would be dumb and this would loop.
*
* If we've just enqueued a TRB that is in the middle of a TD (meaning the
* chain bit is set), then set the chain bit in all the following link TRBs.
* If we've enqueued the last TRB in a TD, make sure the following link TRBs
* have their chain bit cleared (so that each Link TRB is a separate TD).
*
* Section 6.4.4.1 of the 0.95 spec says link TRBs cannot have the chain bit
USB: xhci: Work around for chain bit in link TRBs. Different sections of the xHCI 0.95 specification had opposing requirements for the chain bit in a link transaction request buffer (TRB). The chain bit is used to designate that adjacent TRBs are all part of the same scatter gather list that should be sent to the device. Link TRBs can be in the middle, or at the beginning or end of these chained TRBs. Sections 4.11.5.1 and 6.4.4.1 both stated the link TRB "shall have the chain bit set to 1", meaning it is always chained to the next TRB. However, section 4.6.9 on the stop endpoint command has specific cases for what the hardware must do for a link TRB with the chain bit set to 0. The 0.96 specification errata later cleared up this issue by fixing the 4.11.5.1 and 6.4.4.1 sections to state that a link TRB can have the chain bit set to 1 or 0. The problem is that the xHCI cancellation code depends on the chain bit of the link TRB being cleared when it's at the end of a TD, and some 0.95 xHCI hardware simply stops processing the ring when it encounters a link TRB with the chain bit cleared. Allow users who are testing 0.95 xHCI prototypes to set a module parameter (link_quirk) to turn on this link TRB work around. Cancellation may not work if the ring is stopped exactly on a link TRB with chain bit set, but cancellation should be a relatively uncommon case. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-08-07 21:04:36 +00:00
* set, but other sections talk about dealing with the chain bit set. This was
* fixed in the 0.96 specification errata, but we have to assume that all 0.95
* xHCI hardware can't handle the chain bit being cleared on a link TRB.
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
*
* @more_trbs_coming: Will you enqueue more TRBs before calling
* prepare_transfer()?
*/
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring,
bool consumer, bool more_trbs_coming)
{
u32 chain;
union xhci_trb *next;
unsigned long long addr;
chain = le32_to_cpu(ring->enqueue->generic.field[3]) & TRB_CHAIN;
next = ++(ring->enqueue);
ring->enq_updates++;
/* Update the dequeue pointer further if that was a link TRB or we're at
* the end of an event ring segment (which doesn't have link TRBS)
*/
while (last_trb(xhci, ring, ring->enq_seg, next)) {
if (!consumer) {
if (ring != xhci->event_ring) {
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
/*
* If the caller doesn't plan on enqueueing more
* TDs before ringing the doorbell, then we
* don't want to give the link TRB to the
* hardware just yet. We'll give the link TRB
* back in prepare_ring() just before we enqueue
* the TD at the top of the ring.
*/
if (!chain && !more_trbs_coming)
break;
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
/* If we're not dealing with 0.95 hardware,
* carry over the chain bit of the previous TRB
* (which may mean the chain bit is cleared).
*/
if (!xhci_link_trb_quirk(xhci)) {
next->link.control &=
cpu_to_le32(~TRB_CHAIN);
next->link.control |=
cpu_to_le32(chain);
USB: xhci: Work around for chain bit in link TRBs. Different sections of the xHCI 0.95 specification had opposing requirements for the chain bit in a link transaction request buffer (TRB). The chain bit is used to designate that adjacent TRBs are all part of the same scatter gather list that should be sent to the device. Link TRBs can be in the middle, or at the beginning or end of these chained TRBs. Sections 4.11.5.1 and 6.4.4.1 both stated the link TRB "shall have the chain bit set to 1", meaning it is always chained to the next TRB. However, section 4.6.9 on the stop endpoint command has specific cases for what the hardware must do for a link TRB with the chain bit set to 0. The 0.96 specification errata later cleared up this issue by fixing the 4.11.5.1 and 6.4.4.1 sections to state that a link TRB can have the chain bit set to 1 or 0. The problem is that the xHCI cancellation code depends on the chain bit of the link TRB being cleared when it's at the end of a TD, and some 0.95 xHCI hardware simply stops processing the ring when it encounters a link TRB with the chain bit cleared. Allow users who are testing 0.95 xHCI prototypes to set a module parameter (link_quirk) to turn on this link TRB work around. Cancellation may not work if the ring is stopped exactly on a link TRB with chain bit set, but cancellation should be a relatively uncommon case. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-08-07 21:04:36 +00:00
}
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
/* Give this link TRB to the hardware */
wmb();
next->link.control ^= cpu_to_le32(TRB_CYCLE);
}
/* Toggle the cycle bit after the last ring segment. */
if (last_trb_on_last_seg(xhci, ring, ring->enq_seg, next)) {
ring->cycle_state = (ring->cycle_state ? 0 : 1);
if (!in_interrupt())
xhci_dbg(xhci, "Toggle cycle state for ring %p = %i\n",
ring,
(unsigned int) ring->cycle_state);
}
}
ring->enq_seg = ring->enq_seg->next;
ring->enqueue = ring->enq_seg->trbs;
next = ring->enqueue;
}
addr = (unsigned long long) xhci_trb_virt_to_dma(ring->enq_seg, ring->enqueue);
if (ring == xhci->event_ring)
xhci_dbg(xhci, "Event ring enq = 0x%llx (DMA)\n", addr);
else if (ring == xhci->cmd_ring)
xhci_dbg(xhci, "Command ring enq = 0x%llx (DMA)\n", addr);
else
xhci_dbg(xhci, "Ring enq = 0x%llx (DMA)\n", addr);
}
/*
* Check to see if there's room to enqueue num_trbs on the ring. See rules
* above.
* FIXME: this would be simpler and faster if we just kept track of the number
* of free TRBs in a ring.
*/
static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring,
unsigned int num_trbs)
{
int i;
union xhci_trb *enq = ring->enqueue;
struct xhci_segment *enq_seg = ring->enq_seg;
struct xhci_segment *cur_seg;
unsigned int left_on_ring;
/* If we are currently pointing to a link TRB, advance the
* enqueue pointer before checking for space */
while (last_trb(xhci, ring, enq_seg, enq)) {
enq_seg = enq_seg->next;
enq = enq_seg->trbs;
}
/* Check if ring is empty */
if (enq == ring->dequeue) {
/* Can't use link trbs */
left_on_ring = TRBS_PER_SEGMENT - 1;
for (cur_seg = enq_seg->next; cur_seg != enq_seg;
cur_seg = cur_seg->next)
left_on_ring += TRBS_PER_SEGMENT - 1;
/* Always need one TRB free in the ring. */
left_on_ring -= 1;
if (num_trbs > left_on_ring) {
xhci_warn(xhci, "Not enough room on ring; "
"need %u TRBs, %u TRBs left\n",
num_trbs, left_on_ring);
return 0;
}
return 1;
}
/* Make sure there's an extra empty TRB available */
for (i = 0; i <= num_trbs; ++i) {
if (enq == ring->dequeue)
return 0;
enq++;
while (last_trb(xhci, ring, enq_seg, enq)) {
enq_seg = enq_seg->next;
enq = enq_seg->trbs;
}
}
return 1;
}
/* Ring the host controller doorbell after placing a command on the ring */
void xhci_ring_cmd_db(struct xhci_hcd *xhci)
{
xhci_dbg(xhci, "// Ding dong!\n");
xhci_writel(xhci, DB_VALUE_HOST, &xhci->dba->doorbell[0]);
/* Flush PCI posted writes */
xhci_readl(xhci, &xhci->dba->doorbell[0]);
}
void xhci_ring_ep_doorbell(struct xhci_hcd *xhci,
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
unsigned int slot_id,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int ep_index,
unsigned int stream_id)
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
{
__le32 __iomem *db_addr = &xhci->dba->doorbell[slot_id];
struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index];
unsigned int ep_state = ep->ep_state;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* Don't ring the doorbell for this endpoint if there are pending
* cancellations because we don't want to interrupt processing.
USB: xhci: Add memory allocation for USB3 bulk streams. Add support for allocating streams for USB 3.0 bulk endpoints. See Documentation/usb/bulk-streams.txt for more information about how and why you would use streams. When an endpoint has streams enabled, instead of having one ring where all transfers are enqueued to the hardware, it has several rings. The ring dequeue pointer in the endpoint context is changed to point to a "Stream Context Array". This is basically an array of pointers to transfer rings, one for each stream ID that the driver wants to use. The Stream Context Array size must be a power of two, and host controllers can place a limit on the size of the array (4 to 2^16 entries). These two facts make calculating the size of the Stream Context Array and the number of entries actually used by the driver a bit tricky. Besides the Stream Context Array and rings for all the stream IDs, we need one more data structure. The xHCI hardware will not tell us which stream ID a transfer event was for, but it will give us the slot ID, endpoint index, and physical address for the TRB that caused the event. For every endpoint on a device, add a radix tree to map physical TRB addresses to virtual segments within a stream ring. Keep track of whether an endpoint is transitioning to using streams, and don't enqueue any URBs while that's taking place. Refuse to transition an endpoint to streams if there are already URBs enqueued for that endpoint. We need to make sure that freeing streams does not fail, since a driver's disconnect() function may attempt to do this, and it cannot fail. Pre-allocate the command structure used to issue the Configure Endpoint command, and reserve space on the command ring for each stream endpoint. This may be a bit overkill, but it is permissible for the driver to allocate all streams in one call and free them in multiple calls. (It is not advised, however, since it is a waste of resources and time.) Even with the memory and ring room pre-allocated, freeing streams can still fail because the xHC rejects the configure endpoint command. It is valid (by the xHCI 0.96 spec) to return a "Bandwidth Error" or a "Resource Error" for a configure endpoint command. We should never see a Bandwidth Error, since bulk endpoints do not effect the reserved bandwidth. The host controller can still return a Resource Error, but it's improbable since the xHC would be going from a more resource-intensive configuration (streams) to a less resource-intensive configuration (no streams). If the xHC returns a Resource Error, the endpoint will be stuck with streams and will be unusable for drivers. It's an unavoidable consequence of broken host controller hardware. Includes bug fixes from the original patch, contributed by John Youn <John.Youn@synopsys.com> and Andy Green <AGreen@PLXTech.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:16 +00:00
* We don't want to restart any stream rings if there's a set dequeue
* pointer command pending because the device can choose to start any
* stream once the endpoint is on the HW schedule.
* FIXME - check all the stream rings for pending cancellations.
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
*/
if ((ep_state & EP_HALT_PENDING) || (ep_state & SET_DEQ_PENDING) ||
(ep_state & EP_HALTED))
return;
xhci_writel(xhci, DB_VALUE(ep_index, stream_id), db_addr);
/* The CPU has better things to do at this point than wait for a
* write-posting flush. It'll get there soon enough.
*/
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
/* Ring the doorbell for any rings with pending URBs */
static void ring_doorbell_for_active_rings(struct xhci_hcd *xhci,
unsigned int slot_id,
unsigned int ep_index)
{
unsigned int stream_id;
struct xhci_virt_ep *ep;
ep = &xhci->devs[slot_id]->eps[ep_index];
/* A ring has pending URBs if its TD list is not empty */
if (!(ep->ep_state & EP_HAS_STREAMS)) {
if (!(list_empty(&ep->ring->td_list)))
xhci_ring_ep_doorbell(xhci, slot_id, ep_index, 0);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
return;
}
for (stream_id = 1; stream_id < ep->stream_info->num_streams;
stream_id++) {
struct xhci_stream_info *stream_info = ep->stream_info;
if (!list_empty(&stream_info->stream_rings[stream_id]->td_list))
xhci_ring_ep_doorbell(xhci, slot_id, ep_index,
stream_id);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
}
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/*
* Find the segment that trb is in. Start searching in start_seg.
* If we must move past a segment that has a link TRB with a toggle cycle state
* bit set, then we will toggle the value pointed at by cycle_state.
*/
static struct xhci_segment *find_trb_seg(
struct xhci_segment *start_seg,
union xhci_trb *trb, int *cycle_state)
{
struct xhci_segment *cur_seg = start_seg;
struct xhci_generic_trb *generic_trb;
while (cur_seg->trbs > trb ||
&cur_seg->trbs[TRBS_PER_SEGMENT - 1] < trb) {
generic_trb = &cur_seg->trbs[TRBS_PER_SEGMENT - 1].generic;
if (le32_to_cpu(generic_trb->field[3]) & LINK_TOGGLE)
*cycle_state ^= 0x1;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
cur_seg = cur_seg->next;
if (cur_seg == start_seg)
/* Looped over the entire list. Oops! */
USB: clean up some host controller sparse warnings Fix usb sparse warnings: drivers/usb/host/isp1362-hcd.c:2220:50: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:43:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:49:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:161:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:198:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:319:31: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:1231:33: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-pci.c:177:23: warning: non-ANSI function declaration of function 'xhci_register_pci' drivers/usb/host/xhci-pci.c:182:26: warning: non-ANSI function declaration of function 'xhci_unregister_pci' drivers/usb/host/xhci-ring.c:342:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:525:34: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1009:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1031:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1041:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1096:30: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1100:27: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:224:27: warning: symbol 'xhci_alloc_container_ctx' was not declared. Should it be static? drivers/usb/host/xhci-mem.c:242:6: warning: symbol 'xhci_free_container_ctx' was not declared. Should it be static? Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off By: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-19 15:53:50 +00:00
return NULL;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
return cur_seg;
}
static struct xhci_ring *xhci_triad_to_transfer_ring(struct xhci_hcd *xhci,
unsigned int slot_id, unsigned int ep_index,
unsigned int stream_id)
{
struct xhci_virt_ep *ep;
ep = &xhci->devs[slot_id]->eps[ep_index];
/* Common case: no streams */
if (!(ep->ep_state & EP_HAS_STREAMS))
return ep->ring;
if (stream_id == 0) {
xhci_warn(xhci,
"WARN: Slot ID %u, ep index %u has streams, "
"but URB has no stream ID.\n",
slot_id, ep_index);
return NULL;
}
if (stream_id < ep->stream_info->num_streams)
return ep->stream_info->stream_rings[stream_id];
xhci_warn(xhci,
"WARN: Slot ID %u, ep index %u has "
"stream IDs 1 to %u allocated, "
"but stream ID %u is requested.\n",
slot_id, ep_index,
ep->stream_info->num_streams - 1,
stream_id);
return NULL;
}
/* Get the right ring for the given URB.
* If the endpoint supports streams, boundary check the URB's stream ID.
* If the endpoint doesn't support streams, return the singular endpoint ring.
*/
static struct xhci_ring *xhci_urb_to_transfer_ring(struct xhci_hcd *xhci,
struct urb *urb)
{
return xhci_triad_to_transfer_ring(xhci, urb->dev->slot_id,
xhci_get_endpoint_index(&urb->ep->desc), urb->stream_id);
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/*
* Move the xHC's endpoint ring dequeue pointer past cur_td.
* Record the new state of the xHC's endpoint ring dequeue segment,
* dequeue pointer, and new consumer cycle state in state.
* Update our internal representation of the ring's dequeue pointer.
*
* We do this in three jumps:
* - First we update our new ring state to be the same as when the xHC stopped.
* - Then we traverse the ring to find the segment that contains
* the last TRB in the TD. We toggle the xHC's new cycle state when we pass
* any link TRBs with the toggle cycle bit set.
* - Finally we move the dequeue state one TRB further, toggling the cycle bit
* if we've moved it past a link TRB with the toggle cycle bit set.
*
* Some of the uses of xhci_generic_trb are grotty, but if they're done
* with correct __le32 accesses they should work fine. Only users of this are
* in here.
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
*/
void xhci_find_new_dequeue_state(struct xhci_hcd *xhci,
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
unsigned int slot_id, unsigned int ep_index,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int stream_id, struct xhci_td *cur_td,
struct xhci_dequeue_state *state)
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
{
struct xhci_virt_device *dev = xhci->devs[slot_id];
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
struct xhci_ring *ep_ring;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
struct xhci_generic_trb *trb;
struct xhci_ep_ctx *ep_ctx;
dma_addr_t addr;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep_ring = xhci_triad_to_transfer_ring(xhci, slot_id,
ep_index, stream_id);
if (!ep_ring) {
xhci_warn(xhci, "WARN can't find new dequeue state "
"for invalid stream ID %u.\n",
stream_id);
return;
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
state->new_cycle_state = 0;
xhci_dbg(xhci, "Finding segment containing stopped TRB.\n");
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
state->new_deq_seg = find_trb_seg(cur_td->start_seg,
dev->eps[ep_index].stopped_trb,
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
&state->new_cycle_state);
if (!state->new_deq_seg) {
WARN_ON(1);
return;
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* Dig out the cycle state saved by the xHC during the stop ep cmd */
xhci_dbg(xhci, "Finding endpoint context\n");
ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
state->new_cycle_state = 0x1 & le64_to_cpu(ep_ctx->deq);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
state->new_deq_ptr = cur_td->last_trb;
xhci_dbg(xhci, "Finding segment containing last TRB in TD.\n");
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
state->new_deq_seg = find_trb_seg(state->new_deq_seg,
state->new_deq_ptr,
&state->new_cycle_state);
if (!state->new_deq_seg) {
WARN_ON(1);
return;
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
trb = &state->new_deq_ptr->generic;
if ((le32_to_cpu(trb->field[3]) & TRB_TYPE_BITMASK) ==
TRB_TYPE(TRB_LINK) && (le32_to_cpu(trb->field[3]) & LINK_TOGGLE))
state->new_cycle_state ^= 0x1;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
next_trb(xhci, ep_ring, &state->new_deq_seg, &state->new_deq_ptr);
/*
* If there is only one segment in a ring, find_trb_seg()'s while loop
* will not run, and it will return before it has a chance to see if it
* needs to toggle the cycle bit. It can't tell if the stalled transfer
* ended just before the link TRB on a one-segment ring, or if the TD
* wrapped around the top of the ring, because it doesn't have the TD in
* question. Look for the one-segment case where stalled TRB's address
* is greater than the new dequeue pointer address.
*/
if (ep_ring->first_seg == ep_ring->first_seg->next &&
state->new_deq_ptr < dev->eps[ep_index].stopped_trb)
state->new_cycle_state ^= 0x1;
xhci_dbg(xhci, "Cycle state = 0x%x\n", state->new_cycle_state);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* Don't update the ring cycle state for the producer (us). */
xhci_dbg(xhci, "New dequeue segment = %p (virtual)\n",
state->new_deq_seg);
addr = xhci_trb_virt_to_dma(state->new_deq_seg, state->new_deq_ptr);
xhci_dbg(xhci, "New dequeue pointer = 0x%llx (DMA)\n",
(unsigned long long) addr);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
static void td_to_noop(struct xhci_hcd *xhci, struct xhci_ring *ep_ring,
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
struct xhci_td *cur_td)
{
struct xhci_segment *cur_seg;
union xhci_trb *cur_trb;
for (cur_seg = cur_td->start_seg, cur_trb = cur_td->first_trb;
true;
next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) {
if ((le32_to_cpu(cur_trb->generic.field[3]) & TRB_TYPE_BITMASK)
== TRB_TYPE(TRB_LINK)) {
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* Unchain any chained Link TRBs, but
* leave the pointers intact.
*/
cur_trb->generic.field[3] &= cpu_to_le32(~TRB_CHAIN);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
xhci_dbg(xhci, "Cancel (unchain) link TRB\n");
xhci_dbg(xhci, "Address = %p (0x%llx dma); "
"in seg %p (0x%llx dma)\n",
cur_trb,
(unsigned long long)xhci_trb_virt_to_dma(cur_seg, cur_trb),
cur_seg,
(unsigned long long)cur_seg->dma);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
} else {
cur_trb->generic.field[0] = 0;
cur_trb->generic.field[1] = 0;
cur_trb->generic.field[2] = 0;
/* Preserve only the cycle bit of this TRB */
cur_trb->generic.field[3] &= cpu_to_le32(TRB_CYCLE);
cur_trb->generic.field[3] |= cpu_to_le32(
TRB_TYPE(TRB_TR_NOOP));
xhci_dbg(xhci, "Cancel TRB %p (0x%llx dma) "
"in seg %p (0x%llx dma)\n",
cur_trb,
(unsigned long long)xhci_trb_virt_to_dma(cur_seg, cur_trb),
cur_seg,
(unsigned long long)cur_seg->dma);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
if (cur_trb == cur_td->last_trb)
break;
}
}
static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int ep_index, unsigned int stream_id,
struct xhci_segment *deq_seg,
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
union xhci_trb *deq_ptr, u32 cycle_state);
void xhci_queue_new_dequeue_state(struct xhci_hcd *xhci,
unsigned int slot_id, unsigned int ep_index,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int stream_id,
struct xhci_dequeue_state *deq_state)
{
struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index];
xhci_dbg(xhci, "Set TR Deq Ptr cmd, new deq seg = %p (0x%llx dma), "
"new deq ptr = %p (0x%llx dma), new cycle = %u\n",
deq_state->new_deq_seg,
(unsigned long long)deq_state->new_deq_seg->dma,
deq_state->new_deq_ptr,
(unsigned long long)xhci_trb_virt_to_dma(deq_state->new_deq_seg, deq_state->new_deq_ptr),
deq_state->new_cycle_state);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
queue_set_tr_deq(xhci, slot_id, ep_index, stream_id,
deq_state->new_deq_seg,
deq_state->new_deq_ptr,
(u32) deq_state->new_cycle_state);
/* Stop the TD queueing code from ringing the doorbell until
* this command completes. The HC won't set the dequeue pointer
* if the ring is running, and ringing the doorbell starts the
* ring running.
*/
ep->ep_state |= SET_DEQ_PENDING;
}
static void xhci_stop_watchdog_timer_in_irq(struct xhci_hcd *xhci,
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
struct xhci_virt_ep *ep)
{
ep->ep_state &= ~EP_HALT_PENDING;
/* Can't del_timer_sync in interrupt, so we attempt to cancel. If the
* timer is running on another CPU, we don't decrement stop_cmds_pending
* (since we didn't successfully stop the watchdog timer).
*/
if (del_timer(&ep->stop_cmd_timer))
ep->stop_cmds_pending--;
}
/* Must be called with xhci->lock held in interrupt context */
static void xhci_giveback_urb_in_irq(struct xhci_hcd *xhci,
struct xhci_td *cur_td, int status, char *adjective)
{
struct usb_hcd *hcd;
struct urb *urb;
struct urb_priv *urb_priv;
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
urb = cur_td->urb;
urb_priv = urb->hcpriv;
urb_priv->td_cnt++;
hcd = bus_to_hcd(urb->dev->bus);
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
/* Only giveback urb when this is the last td in urb */
if (urb_priv->td_cnt == urb_priv->length) {
if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs--;
if (xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs == 0) {
if (xhci->quirks & XHCI_AMD_PLL_FIX)
usb_amd_quirk_pll_enable();
}
}
usb_hcd_unlink_urb_from_ep(hcd, urb);
xhci_dbg(xhci, "Giveback %s URB %p\n", adjective, urb);
spin_unlock(&xhci->lock);
usb_hcd_giveback_urb(hcd, urb, status);
xhci_urb_free_priv(xhci, urb_priv);
spin_lock(&xhci->lock);
xhci_dbg(xhci, "%s URB given back\n", adjective);
}
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/*
* When we get a command completion for a Stop Endpoint Command, we need to
* unlink any cancelled TDs from the ring. There are two ways to do that:
*
* 1. If the HW was in the middle of processing the TD that needs to be
* cancelled, then we must move the ring's dequeue pointer past the last TRB
* in the TD with a Set Dequeue Pointer Command.
* 2. Otherwise, we turn all the TRBs in the TD into No-op TRBs (with the chain
* bit cleared) so that the HW will skip over them.
*/
static void handle_stopped_endpoint(struct xhci_hcd *xhci,
union xhci_trb *trb, struct xhci_event_cmd *event)
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
{
unsigned int slot_id;
unsigned int ep_index;
struct xhci_virt_device *virt_dev;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
struct xhci_ring *ep_ring;
struct xhci_virt_ep *ep;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
struct list_head *entry;
USB: clean up some host controller sparse warnings Fix usb sparse warnings: drivers/usb/host/isp1362-hcd.c:2220:50: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:43:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:49:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:161:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:198:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:319:31: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:1231:33: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-pci.c:177:23: warning: non-ANSI function declaration of function 'xhci_register_pci' drivers/usb/host/xhci-pci.c:182:26: warning: non-ANSI function declaration of function 'xhci_unregister_pci' drivers/usb/host/xhci-ring.c:342:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:525:34: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1009:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1031:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1041:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1096:30: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1100:27: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:224:27: warning: symbol 'xhci_alloc_container_ctx' was not declared. Should it be static? drivers/usb/host/xhci-mem.c:242:6: warning: symbol 'xhci_free_container_ctx' was not declared. Should it be static? Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off By: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-19 15:53:50 +00:00
struct xhci_td *cur_td = NULL;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
struct xhci_td *last_unlinked_td;
struct xhci_dequeue_state deq_state;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
if (unlikely(TRB_TO_SUSPEND_PORT(
le32_to_cpu(xhci->cmd_ring->dequeue->generic.field[3])))) {
slot_id = TRB_TO_SLOT_ID(
le32_to_cpu(xhci->cmd_ring->dequeue->generic.field[3]));
virt_dev = xhci->devs[slot_id];
if (virt_dev)
handle_cmd_in_cmd_wait_list(xhci, virt_dev,
event);
else
xhci_warn(xhci, "Stop endpoint command "
"completion for disabled slot %u\n",
slot_id);
return;
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
memset(&deq_state, 0, sizeof(deq_state));
slot_id = TRB_TO_SLOT_ID(le32_to_cpu(trb->generic.field[3]));
ep_index = TRB_TO_EP_INDEX(le32_to_cpu(trb->generic.field[3]));
ep = &xhci->devs[slot_id]->eps[ep_index];
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
USB: xhci: Handle URB cancel, complete and resubmit race. In the old code, there was a race condition between the stop endpoint command and the URB submission process. When the stop endpoint command is handled by the event handler, the endpoint ring is assumed to be stopped. When a stop endpoint command is queued, URB submissions are to not ring the doorbell. The old code would check the number of pending URBs to be canceled, and would not ring the doorbell if it was non-zero. However, the following race condition could occur with the old code: 1. Cancel an URB, add it to the list of URBs to be canceled, queue the stop endpoint command, and increment ep->cancels_pending to 1. 2. The URB finishes on the HW, and an event is enqueued to the event ring (at the same time as 1). 3. The stop endpoint command finishes, and the endpoint is halted. An event is queued to the event ring. 4. The event handler sees the finished URB, notices it was to be canceled, decrements ep->cancels_pending to 0, and removes it from the to be canceled list. 5. The event handler drops the lock and gives back the URB. The completion handler requeues the URB (or a different driver enqueues a new URB). This causes the endpoint's doorbell to be rung, since ep->cancels_pending == 0. The endpoint is now running. 6. A second URB is canceled, and it's added to the canceled list. Since ep->cancels_pending == 0, a new stop endpoint command is queued, and ep->cancels_pending is incremented to 1. 7. The event handler then sees the completed stop endpoint command. The handler assumes the endpoint is stopped, but it isn't. It attempts to move the dequeue pointer or change TDs to cancel the second URB, while the hardware is actively accessing the endpoint ring. To eliminate this race condition, a new endpoint state bit is introduced, EP_HALT_PENDING. When this bit is set, a stop endpoint command has been queued, and the command handler has not begun to process the URB cancellation list yet. The endpoint doorbell should not be rung when this is set. Set this when a stop endpoint command is queued, clear it when the handler for that command runs, and check if it's set before ringing a doorbell. ep->cancels_pending is eliminated, because it is no longer used. Make sure to ring the doorbell for an endpoint when the stop endpoint command handler runs, even if the canceled URB list is empty. All canceled URBs could have completed and new URBs could have been enqueued without the doorbell being rung before the command was handled. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:55:52 +00:00
if (list_empty(&ep->cancelled_td_list)) {
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
xhci_stop_watchdog_timer_in_irq(xhci, ep);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
return;
USB: xhci: Handle URB cancel, complete and resubmit race. In the old code, there was a race condition between the stop endpoint command and the URB submission process. When the stop endpoint command is handled by the event handler, the endpoint ring is assumed to be stopped. When a stop endpoint command is queued, URB submissions are to not ring the doorbell. The old code would check the number of pending URBs to be canceled, and would not ring the doorbell if it was non-zero. However, the following race condition could occur with the old code: 1. Cancel an URB, add it to the list of URBs to be canceled, queue the stop endpoint command, and increment ep->cancels_pending to 1. 2. The URB finishes on the HW, and an event is enqueued to the event ring (at the same time as 1). 3. The stop endpoint command finishes, and the endpoint is halted. An event is queued to the event ring. 4. The event handler sees the finished URB, notices it was to be canceled, decrements ep->cancels_pending to 0, and removes it from the to be canceled list. 5. The event handler drops the lock and gives back the URB. The completion handler requeues the URB (or a different driver enqueues a new URB). This causes the endpoint's doorbell to be rung, since ep->cancels_pending == 0. The endpoint is now running. 6. A second URB is canceled, and it's added to the canceled list. Since ep->cancels_pending == 0, a new stop endpoint command is queued, and ep->cancels_pending is incremented to 1. 7. The event handler then sees the completed stop endpoint command. The handler assumes the endpoint is stopped, but it isn't. It attempts to move the dequeue pointer or change TDs to cancel the second URB, while the hardware is actively accessing the endpoint ring. To eliminate this race condition, a new endpoint state bit is introduced, EP_HALT_PENDING. When this bit is set, a stop endpoint command has been queued, and the command handler has not begun to process the URB cancellation list yet. The endpoint doorbell should not be rung when this is set. Set this when a stop endpoint command is queued, clear it when the handler for that command runs, and check if it's set before ringing a doorbell. ep->cancels_pending is eliminated, because it is no longer used. Make sure to ring the doorbell for an endpoint when the stop endpoint command handler runs, even if the canceled URB list is empty. All canceled URBs could have completed and new URBs could have been enqueued without the doorbell being rung before the command was handled. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:55:52 +00:00
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* Fix up the ep ring first, so HW stops executing cancelled TDs.
* We have the xHCI lock, so nothing can modify this list until we drop
* it. We're also in the event handler, so we can't get re-interrupted
* if another Stop Endpoint command completes
*/
list_for_each(entry, &ep->cancelled_td_list) {
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
cur_td = list_entry(entry, struct xhci_td, cancelled_td_list);
xhci_dbg(xhci, "Cancelling TD starting at %p, 0x%llx (dma).\n",
cur_td->first_trb,
(unsigned long long)xhci_trb_virt_to_dma(cur_td->start_seg, cur_td->first_trb));
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep_ring = xhci_urb_to_transfer_ring(xhci, cur_td->urb);
if (!ep_ring) {
/* This shouldn't happen unless a driver is mucking
* with the stream ID after submission. This will
* leave the TD on the hardware ring, and the hardware
* will try to execute it, and may access a buffer
* that has already been freed. In the best case, the
* hardware will execute it, and the event handler will
* ignore the completion event for that TD, since it was
* removed from the td_list for that endpoint. In
* short, don't muck with the stream ID after
* submission.
*/
xhci_warn(xhci, "WARN Cancelled URB %p "
"has invalid stream ID %u.\n",
cur_td->urb,
cur_td->urb->stream_id);
goto remove_finished_td;
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/*
* If we stopped on the TD we need to cancel, then we have to
* move the xHC endpoint ring dequeue pointer past this TD.
*/
if (cur_td == ep->stopped_td)
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
xhci_find_new_dequeue_state(xhci, slot_id, ep_index,
cur_td->urb->stream_id,
cur_td, &deq_state);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
else
td_to_noop(xhci, ep_ring, cur_td);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
remove_finished_td:
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/*
* The event handler won't see a completion for this TD anymore,
* so remove it from the endpoint ring's TD list. Keep it in
* the cancelled TD list for URB completion later.
*/
list_del(&cur_td->td_list);
}
last_unlinked_td = cur_td;
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
xhci_stop_watchdog_timer_in_irq(xhci, ep);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* If necessary, queue a Set Transfer Ring Dequeue Pointer command */
if (deq_state.new_deq_ptr && deq_state.new_deq_seg) {
xhci_queue_new_dequeue_state(xhci,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
slot_id, ep_index,
ep->stopped_td->urb->stream_id,
&deq_state);
xhci_ring_cmd_db(xhci);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
} else {
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
/* Otherwise ring the doorbell(s) to restart queued transfers */
ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
ep->stopped_td = NULL;
ep->stopped_trb = NULL;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/*
* Drop the lock and complete the URBs in the cancelled TD list.
* New TDs to be cancelled might be added to the end of the list before
* we can complete all the URBs for the TDs we already unlinked.
* So stop when we've completed the URB for the last TD we unlinked.
*/
do {
cur_td = list_entry(ep->cancelled_td_list.next,
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
struct xhci_td, cancelled_td_list);
list_del(&cur_td->cancelled_td_list);
/* Clean up the cancelled URB */
/* Doesn't matter what we pass for status, since the core will
* just overwrite it (because the URB has been unlinked).
*/
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
xhci_giveback_urb_in_irq(xhci, cur_td, 0, "cancelled");
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
/* Stop processing the cancelled list if the watchdog timer is
* running.
*/
if (xhci->xhc_state & XHCI_STATE_DYING)
return;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
} while (cur_td != last_unlinked_td);
/* Return to the event handler with xhci->lock re-acquired */
}
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
/* Watchdog timer function for when a stop endpoint command fails to complete.
* In this case, we assume the host controller is broken or dying or dead. The
* host may still be completing some other events, so we have to be careful to
* let the event ring handler and the URB dequeueing/enqueueing functions know
* through xhci->state.
*
* The timer may also fire if the host takes a very long time to respond to the
* command, and the stop endpoint command completion handler cannot delete the
* timer before the timer function is called. Another endpoint cancellation may
* sneak in before the timer function can grab the lock, and that may queue
* another stop endpoint command and add the timer back. So we cannot use a
* simple flag to say whether there is a pending stop endpoint command for a
* particular endpoint.
*
* Instead we use a combination of that flag and a counter for the number of
* pending stop endpoint commands. If the timer is the tail end of the last
* stop endpoint command, and the endpoint's command is still pending, we assume
* the host is dying.
*/
void xhci_stop_endpoint_command_watchdog(unsigned long arg)
{
struct xhci_hcd *xhci;
struct xhci_virt_ep *ep;
struct xhci_virt_ep *temp_ep;
struct xhci_ring *ring;
struct xhci_td *cur_td;
int ret, i, j;
ep = (struct xhci_virt_ep *) arg;
xhci = ep->xhci;
spin_lock(&xhci->lock);
ep->stop_cmds_pending--;
if (xhci->xhc_state & XHCI_STATE_DYING) {
xhci_dbg(xhci, "Stop EP timer ran, but another timer marked "
"xHCI as DYING, exiting.\n");
spin_unlock(&xhci->lock);
return;
}
if (!(ep->stop_cmds_pending == 0 && (ep->ep_state & EP_HALT_PENDING))) {
xhci_dbg(xhci, "Stop EP timer ran, but no command pending, "
"exiting.\n");
spin_unlock(&xhci->lock);
return;
}
xhci_warn(xhci, "xHCI host not responding to stop endpoint command.\n");
xhci_warn(xhci, "Assuming host is dying, halting host.\n");
/* Oops, HC is dead or dying or at least not responding to the stop
* endpoint command.
*/
xhci->xhc_state |= XHCI_STATE_DYING;
/* Disable interrupts from the host controller and start halting it */
xhci_quiesce(xhci);
spin_unlock(&xhci->lock);
ret = xhci_halt(xhci);
spin_lock(&xhci->lock);
if (ret < 0) {
/* This is bad; the host is not responding to commands and it's
* not allowing itself to be halted. At least interrupts are
* disabled. If we call usb_hc_died(), it will attempt to
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
* disconnect all device drivers under this host. Those
* disconnect() methods will wait for all URBs to be unlinked,
* so we must complete them.
*/
xhci_warn(xhci, "Non-responsive xHCI host is not halting.\n");
xhci_warn(xhci, "Completing active URBs anyway.\n");
/* We could turn all TDs on the rings to no-ops. This won't
* help if the host has cached part of the ring, and is slow if
* we want to preserve the cycle bit. Skip it and hope the host
* doesn't touch the memory.
*/
}
for (i = 0; i < MAX_HC_SLOTS; i++) {
if (!xhci->devs[i])
continue;
for (j = 0; j < 31; j++) {
temp_ep = &xhci->devs[i]->eps[j];
ring = temp_ep->ring;
if (!ring)
continue;
xhci_dbg(xhci, "Killing URBs for slot ID %u, "
"ep index %u\n", i, j);
while (!list_empty(&ring->td_list)) {
cur_td = list_first_entry(&ring->td_list,
struct xhci_td,
td_list);
list_del(&cur_td->td_list);
if (!list_empty(&cur_td->cancelled_td_list))
list_del(&cur_td->cancelled_td_list);
xhci_giveback_urb_in_irq(xhci, cur_td,
-ESHUTDOWN, "killed");
}
while (!list_empty(&temp_ep->cancelled_td_list)) {
cur_td = list_first_entry(
&temp_ep->cancelled_td_list,
struct xhci_td,
cancelled_td_list);
list_del(&cur_td->cancelled_td_list);
xhci_giveback_urb_in_irq(xhci, cur_td,
-ESHUTDOWN, "killed");
}
}
}
spin_unlock(&xhci->lock);
xhci_dbg(xhci, "Calling usb_hc_died()\n");
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
usb_hc_died(xhci_to_hcd(xhci)->primary_hcd);
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
xhci_dbg(xhci, "xHCI host controller is dead.\n");
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/*
* When we get a completion for a Set Transfer Ring Dequeue Pointer command,
* we need to clear the set deq pending flag in the endpoint ring state, so that
* the TD queueing code can ring the doorbell again. We also need to ring the
* endpoint doorbell to restart the ring, but only if there aren't more
* cancellations pending.
*/
static void handle_set_deq_completion(struct xhci_hcd *xhci,
struct xhci_event_cmd *event,
union xhci_trb *trb)
{
unsigned int slot_id;
unsigned int ep_index;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int stream_id;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
struct xhci_ring *ep_ring;
struct xhci_virt_device *dev;
struct xhci_ep_ctx *ep_ctx;
struct xhci_slot_ctx *slot_ctx;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
slot_id = TRB_TO_SLOT_ID(le32_to_cpu(trb->generic.field[3]));
ep_index = TRB_TO_EP_INDEX(le32_to_cpu(trb->generic.field[3]));
stream_id = TRB_TO_STREAM_ID(le32_to_cpu(trb->generic.field[2]));
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
dev = xhci->devs[slot_id];
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep_ring = xhci_stream_id_to_ring(dev, ep_index, stream_id);
if (!ep_ring) {
xhci_warn(xhci, "WARN Set TR deq ptr command for "
"freed stream ID %u\n",
stream_id);
/* XXX: Harmless??? */
dev->eps[ep_index].ep_state &= ~SET_DEQ_PENDING;
return;
}
ep_ctx = xhci_get_ep_ctx(xhci, dev->out_ctx, ep_index);
slot_ctx = xhci_get_slot_ctx(xhci, dev->out_ctx);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
if (GET_COMP_CODE(le32_to_cpu(event->status)) != COMP_SUCCESS) {
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
unsigned int ep_state;
unsigned int slot_state;
switch (GET_COMP_CODE(le32_to_cpu(event->status))) {
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
case COMP_TRB_ERR:
xhci_warn(xhci, "WARN Set TR Deq Ptr cmd invalid because "
"of stream ID configuration\n");
break;
case COMP_CTX_STATE:
xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed due "
"to incorrect slot or ep state.\n");
ep_state = le32_to_cpu(ep_ctx->ep_info);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
ep_state &= EP_STATE_MASK;
slot_state = le32_to_cpu(slot_ctx->dev_state);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
slot_state = GET_SLOT_STATE(slot_state);
xhci_dbg(xhci, "Slot state = %u, EP state = %u\n",
slot_state, ep_state);
break;
case COMP_EBADSLT:
xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed because "
"slot %u was not enabled.\n", slot_id);
break;
default:
xhci_warn(xhci, "WARN Set TR Deq Ptr cmd with unknown "
"completion code of %u.\n",
GET_COMP_CODE(le32_to_cpu(event->status)));
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
break;
}
/* OK what do we do now? The endpoint state is hosed, and we
* should never get to this point if the synchronization between
* queueing, and endpoint state are correct. This might happen
* if the device gets disconnected after we've finished
* cancelling URBs, which might not be an error...
*/
} else {
xhci_dbg(xhci, "Successful Set TR Deq Ptr cmd, deq = @%08llx\n",
le64_to_cpu(ep_ctx->deq));
xhci: Update internal dequeue pointers after stalls. When an endpoint stalls, the xHCI driver must move the endpoint ring's dequeue pointer past the stalled transfer. To do that, the driver issues a Set TR Dequeue Pointer command, which will complete some time later. Takashi was having issues with USB 1.1 audio devices that stalled, and his analysis of the code was that the old code would not update the xHCI driver's ring dequeue pointer after the command completes. However, the dequeue pointer is set in xhci_find_new_dequeue_state(), just before the set command is issued to the hardware. Setting the dequeue pointer before the Set TR Dequeue Pointer command completes is a dangerous thing to do, since the xHCI hardware can fail the command. Instead, store the new dequeue pointer in the xhci_virt_ep structure, and update the ring's dequeue pointer when the Set TR dequeue pointer command completes. While we're at it, make sure we can't queue another Set TR Dequeue Command while the first one is still being processed. This just won't work with the internal xHCI state code. I'm still not sure if this is the right thing to do, since we might have a case where a driver queues multiple URBs to a control ring, one of the URBs Stalls, and then the driver tries to cancel the second URB. There may be a race condition there where the xHCI driver might try to issue multiple Set TR Dequeue Pointer commands, but I would have to think very hard about how the Stop Endpoint and cancellation code works. Keep the fix simple until when/if we run into that case. This patch should be queued to kernels all the way back to 2.6.31. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Takashi Iwai <tiwai@suse.de> Cc: stable@kernel.org
2011-02-23 23:46:42 +00:00
if (xhci_trb_virt_to_dma(dev->eps[ep_index].queued_deq_seg,
dev->eps[ep_index].queued_deq_ptr) ==
(le64_to_cpu(ep_ctx->deq) & ~(EP_CTX_CYCLE_MASK))) {
xhci: Update internal dequeue pointers after stalls. When an endpoint stalls, the xHCI driver must move the endpoint ring's dequeue pointer past the stalled transfer. To do that, the driver issues a Set TR Dequeue Pointer command, which will complete some time later. Takashi was having issues with USB 1.1 audio devices that stalled, and his analysis of the code was that the old code would not update the xHCI driver's ring dequeue pointer after the command completes. However, the dequeue pointer is set in xhci_find_new_dequeue_state(), just before the set command is issued to the hardware. Setting the dequeue pointer before the Set TR Dequeue Pointer command completes is a dangerous thing to do, since the xHCI hardware can fail the command. Instead, store the new dequeue pointer in the xhci_virt_ep structure, and update the ring's dequeue pointer when the Set TR dequeue pointer command completes. While we're at it, make sure we can't queue another Set TR Dequeue Command while the first one is still being processed. This just won't work with the internal xHCI state code. I'm still not sure if this is the right thing to do, since we might have a case where a driver queues multiple URBs to a control ring, one of the URBs Stalls, and then the driver tries to cancel the second URB. There may be a race condition there where the xHCI driver might try to issue multiple Set TR Dequeue Pointer commands, but I would have to think very hard about how the Stop Endpoint and cancellation code works. Keep the fix simple until when/if we run into that case. This patch should be queued to kernels all the way back to 2.6.31. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Takashi Iwai <tiwai@suse.de> Cc: stable@kernel.org
2011-02-23 23:46:42 +00:00
/* Update the ring's dequeue segment and dequeue pointer
* to reflect the new position.
*/
ep_ring->deq_seg = dev->eps[ep_index].queued_deq_seg;
ep_ring->dequeue = dev->eps[ep_index].queued_deq_ptr;
} else {
xhci_warn(xhci, "Mismatch between completed Set TR Deq "
"Ptr command & xHCI internal state.\n");
xhci_warn(xhci, "ep deq seg = %p, deq ptr = %p\n",
dev->eps[ep_index].queued_deq_seg,
dev->eps[ep_index].queued_deq_ptr);
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
dev->eps[ep_index].ep_state &= ~SET_DEQ_PENDING;
xhci: Update internal dequeue pointers after stalls. When an endpoint stalls, the xHCI driver must move the endpoint ring's dequeue pointer past the stalled transfer. To do that, the driver issues a Set TR Dequeue Pointer command, which will complete some time later. Takashi was having issues with USB 1.1 audio devices that stalled, and his analysis of the code was that the old code would not update the xHCI driver's ring dequeue pointer after the command completes. However, the dequeue pointer is set in xhci_find_new_dequeue_state(), just before the set command is issued to the hardware. Setting the dequeue pointer before the Set TR Dequeue Pointer command completes is a dangerous thing to do, since the xHCI hardware can fail the command. Instead, store the new dequeue pointer in the xhci_virt_ep structure, and update the ring's dequeue pointer when the Set TR dequeue pointer command completes. While we're at it, make sure we can't queue another Set TR Dequeue Command while the first one is still being processed. This just won't work with the internal xHCI state code. I'm still not sure if this is the right thing to do, since we might have a case where a driver queues multiple URBs to a control ring, one of the URBs Stalls, and then the driver tries to cancel the second URB. There may be a race condition there where the xHCI driver might try to issue multiple Set TR Dequeue Pointer commands, but I would have to think very hard about how the Stop Endpoint and cancellation code works. Keep the fix simple until when/if we run into that case. This patch should be queued to kernels all the way back to 2.6.31. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Takashi Iwai <tiwai@suse.de> Cc: stable@kernel.org
2011-02-23 23:46:42 +00:00
dev->eps[ep_index].queued_deq_seg = NULL;
dev->eps[ep_index].queued_deq_ptr = NULL;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
/* Restart any rings with pending URBs */
ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
static void handle_reset_ep_completion(struct xhci_hcd *xhci,
struct xhci_event_cmd *event,
union xhci_trb *trb)
{
int slot_id;
unsigned int ep_index;
slot_id = TRB_TO_SLOT_ID(le32_to_cpu(trb->generic.field[3]));
ep_index = TRB_TO_EP_INDEX(le32_to_cpu(trb->generic.field[3]));
/* This command will only fail if the endpoint wasn't halted,
* but we don't care.
*/
xhci_dbg(xhci, "Ignoring reset ep completion code of %u\n",
(unsigned int) GET_COMP_CODE(le32_to_cpu(event->status)));
/* HW with the reset endpoint quirk needs to have a configure endpoint
* command complete before the endpoint can be used. Queue that here
* because the HW can't handle two commands being queued in a row.
*/
if (xhci->quirks & XHCI_RESET_EP_QUIRK) {
xhci_dbg(xhci, "Queueing configure endpoint command\n");
xhci_queue_configure_endpoint(xhci,
xhci->devs[slot_id]->in_ctx->dma, slot_id,
false);
xhci_ring_cmd_db(xhci);
} else {
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
/* Clear our internal halted state and restart the ring(s) */
xhci->devs[slot_id]->eps[ep_index].ep_state &= ~EP_HALTED;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
}
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* Check to see if a command in the device's command queue matches this one.
* Signal the completion or free the command, and return 1. Return 0 if the
* completed command isn't at the head of the command list.
*/
static int handle_cmd_in_cmd_wait_list(struct xhci_hcd *xhci,
struct xhci_virt_device *virt_dev,
struct xhci_event_cmd *event)
{
struct xhci_command *command;
if (list_empty(&virt_dev->cmd_list))
return 0;
command = list_entry(virt_dev->cmd_list.next,
struct xhci_command, cmd_list);
if (xhci->cmd_ring->dequeue != command->command_trb)
return 0;
command->status = GET_COMP_CODE(le32_to_cpu(event->status));
list_del(&command->cmd_list);
if (command->completion)
complete(command->completion);
else
xhci_free_command(xhci, command);
return 1;
}
static void handle_cmd_completion(struct xhci_hcd *xhci,
struct xhci_event_cmd *event)
{
int slot_id = TRB_TO_SLOT_ID(le32_to_cpu(event->flags));
u64 cmd_dma;
dma_addr_t cmd_dequeue_dma;
struct xhci_input_control_ctx *ctrl_ctx;
struct xhci_virt_device *virt_dev;
unsigned int ep_index;
struct xhci_ring *ep_ring;
unsigned int ep_state;
cmd_dma = le64_to_cpu(event->cmd_trb);
cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg,
xhci->cmd_ring->dequeue);
/* Is the command ring deq ptr out of sync with the deq seg ptr? */
if (cmd_dequeue_dma == 0) {
xhci->error_bitmask |= 1 << 4;
return;
}
/* Does the DMA address match our internal dequeue pointer address? */
if (cmd_dma != (u64) cmd_dequeue_dma) {
xhci->error_bitmask |= 1 << 5;
return;
}
switch (le32_to_cpu(xhci->cmd_ring->dequeue->generic.field[3])
& TRB_TYPE_BITMASK) {
case TRB_TYPE(TRB_ENABLE_SLOT):
if (GET_COMP_CODE(le32_to_cpu(event->status)) == COMP_SUCCESS)
xhci->slot_id = slot_id;
else
xhci->slot_id = 0;
complete(&xhci->addr_dev);
break;
case TRB_TYPE(TRB_DISABLE_SLOT):
if (xhci->devs[slot_id])
xhci_free_virt_device(xhci, slot_id);
break;
USB: xhci: Bandwidth allocation support Since the xHCI host controller hardware (xHC) has an internal schedule, it needs a better representation of what devices are consuming bandwidth on the bus. Each device is represented by a device context, with data about the device, endpoints, and pointers to each endpoint ring. We need to update the endpoint information for a device context before a new configuration or alternate interface setting is selected. We setup an input device context with modified endpoint information and newly allocated endpoint rings, and then submit a Configure Endpoint Command to the hardware. The host controller can reject the new configuration if it exceeds the bus bandwidth, or the host controller doesn't have enough internal resources for the configuration. If the command fails, we still have the older device context with the previous configuration. If the command succeeds, we free the old endpoint rings. The root hub isn't a real device, so always say yes to any bandwidth changes for it. The USB core will enable, disable, and then enable endpoint 0 several times during the initialization sequence. The device will always have an endpoint ring for endpoint 0 and bandwidth allocated for that, unless the device is disconnected or gets a SetAddress 0 request. So we don't pay attention for when xhci_check_bandwidth() is called for a re-add of endpoint 0. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 02:58:38 +00:00
case TRB_TYPE(TRB_CONFIG_EP):
virt_dev = xhci->devs[slot_id];
if (handle_cmd_in_cmd_wait_list(xhci, virt_dev, event))
break;
/*
* Configure endpoint commands can come from the USB core
* configuration or alt setting changes, or because the HW
* needed an extra configure endpoint command after a reset
USB: xhci: Add memory allocation for USB3 bulk streams. Add support for allocating streams for USB 3.0 bulk endpoints. See Documentation/usb/bulk-streams.txt for more information about how and why you would use streams. When an endpoint has streams enabled, instead of having one ring where all transfers are enqueued to the hardware, it has several rings. The ring dequeue pointer in the endpoint context is changed to point to a "Stream Context Array". This is basically an array of pointers to transfer rings, one for each stream ID that the driver wants to use. The Stream Context Array size must be a power of two, and host controllers can place a limit on the size of the array (4 to 2^16 entries). These two facts make calculating the size of the Stream Context Array and the number of entries actually used by the driver a bit tricky. Besides the Stream Context Array and rings for all the stream IDs, we need one more data structure. The xHCI hardware will not tell us which stream ID a transfer event was for, but it will give us the slot ID, endpoint index, and physical address for the TRB that caused the event. For every endpoint on a device, add a radix tree to map physical TRB addresses to virtual segments within a stream ring. Keep track of whether an endpoint is transitioning to using streams, and don't enqueue any URBs while that's taking place. Refuse to transition an endpoint to streams if there are already URBs enqueued for that endpoint. We need to make sure that freeing streams does not fail, since a driver's disconnect() function may attempt to do this, and it cannot fail. Pre-allocate the command structure used to issue the Configure Endpoint command, and reserve space on the command ring for each stream endpoint. This may be a bit overkill, but it is permissible for the driver to allocate all streams in one call and free them in multiple calls. (It is not advised, however, since it is a waste of resources and time.) Even with the memory and ring room pre-allocated, freeing streams can still fail because the xHC rejects the configure endpoint command. It is valid (by the xHCI 0.96 spec) to return a "Bandwidth Error" or a "Resource Error" for a configure endpoint command. We should never see a Bandwidth Error, since bulk endpoints do not effect the reserved bandwidth. The host controller can still return a Resource Error, but it's improbable since the xHC would be going from a more resource-intensive configuration (streams) to a less resource-intensive configuration (no streams). If the xHC returns a Resource Error, the endpoint will be stuck with streams and will be unusable for drivers. It's an unavoidable consequence of broken host controller hardware. Includes bug fixes from the original patch, contributed by John Youn <John.Youn@synopsys.com> and Andy Green <AGreen@PLXTech.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:16 +00:00
* endpoint command or streams were being configured.
* If the command was for a halted endpoint, the xHCI driver
* is not waiting on the configure endpoint command.
*/
ctrl_ctx = xhci_get_input_control_ctx(xhci,
virt_dev->in_ctx);
/* Input ctx add_flags are the endpoint index plus one */
ep_index = xhci_last_valid_endpoint(le32_to_cpu(ctrl_ctx->add_flags)) - 1;
/* A usb_set_interface() call directly after clearing a halted
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
* condition may race on this quirky hardware. Not worth
* worrying about, since this is prototype hardware. Not sure
* if this will work for streams, but streams support was
* untested on this prototype.
*/
if (xhci->quirks & XHCI_RESET_EP_QUIRK &&
ep_index != (unsigned int) -1 &&
le32_to_cpu(ctrl_ctx->add_flags) - SLOT_FLAG ==
le32_to_cpu(ctrl_ctx->drop_flags)) {
ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
ep_state = xhci->devs[slot_id]->eps[ep_index].ep_state;
if (!(ep_state & EP_HALTED))
goto bandwidth_change;
xhci_dbg(xhci, "Completed config ep cmd - "
"last ep index = %d, state = %d\n",
ep_index, ep_state);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
/* Clear internal halted state and restart ring(s) */
xhci->devs[slot_id]->eps[ep_index].ep_state &=
~EP_HALTED;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ring_doorbell_for_active_rings(xhci, slot_id, ep_index);
break;
}
bandwidth_change:
xhci_dbg(xhci, "Completed config ep cmd\n");
xhci->devs[slot_id]->cmd_status =
GET_COMP_CODE(le32_to_cpu(event->status));
complete(&xhci->devs[slot_id]->cmd_completion);
USB: xhci: Bandwidth allocation support Since the xHCI host controller hardware (xHC) has an internal schedule, it needs a better representation of what devices are consuming bandwidth on the bus. Each device is represented by a device context, with data about the device, endpoints, and pointers to each endpoint ring. We need to update the endpoint information for a device context before a new configuration or alternate interface setting is selected. We setup an input device context with modified endpoint information and newly allocated endpoint rings, and then submit a Configure Endpoint Command to the hardware. The host controller can reject the new configuration if it exceeds the bus bandwidth, or the host controller doesn't have enough internal resources for the configuration. If the command fails, we still have the older device context with the previous configuration. If the command succeeds, we free the old endpoint rings. The root hub isn't a real device, so always say yes to any bandwidth changes for it. The USB core will enable, disable, and then enable endpoint 0 several times during the initialization sequence. The device will always have an endpoint ring for endpoint 0 and bandwidth allocated for that, unless the device is disconnected or gets a SetAddress 0 request. So we don't pay attention for when xhci_check_bandwidth() is called for a re-add of endpoint 0. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 02:58:38 +00:00
break;
case TRB_TYPE(TRB_EVAL_CONTEXT):
virt_dev = xhci->devs[slot_id];
if (handle_cmd_in_cmd_wait_list(xhci, virt_dev, event))
break;
xhci->devs[slot_id]->cmd_status = GET_COMP_CODE(le32_to_cpu(event->status));
complete(&xhci->devs[slot_id]->cmd_completion);
break;
case TRB_TYPE(TRB_ADDR_DEV):
xhci->devs[slot_id]->cmd_status = GET_COMP_CODE(le32_to_cpu(event->status));
complete(&xhci->addr_dev);
break;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
case TRB_TYPE(TRB_STOP_RING):
handle_stopped_endpoint(xhci, xhci->cmd_ring->dequeue, event);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
break;
case TRB_TYPE(TRB_SET_DEQ):
handle_set_deq_completion(xhci, event, xhci->cmd_ring->dequeue);
break;
case TRB_TYPE(TRB_CMD_NOOP):
break;
case TRB_TYPE(TRB_RESET_EP):
handle_reset_ep_completion(xhci, event, xhci->cmd_ring->dequeue);
break;
case TRB_TYPE(TRB_RESET_DEV):
xhci_dbg(xhci, "Completed reset device command.\n");
slot_id = TRB_TO_SLOT_ID(
le32_to_cpu(xhci->cmd_ring->dequeue->generic.field[3]));
virt_dev = xhci->devs[slot_id];
if (virt_dev)
handle_cmd_in_cmd_wait_list(xhci, virt_dev, event);
else
xhci_warn(xhci, "Reset device command completion "
"for disabled slot %u\n", slot_id);
break;
case TRB_TYPE(TRB_NEC_GET_FW):
if (!(xhci->quirks & XHCI_NEC_HOST)) {
xhci->error_bitmask |= 1 << 6;
break;
}
xhci_dbg(xhci, "NEC firmware version %2x.%02x\n",
NEC_FW_MAJOR(le32_to_cpu(event->status)),
NEC_FW_MINOR(le32_to_cpu(event->status)));
break;
default:
/* Skip over unknown commands on the event ring */
xhci->error_bitmask |= 1 << 6;
break;
}
inc_deq(xhci, xhci->cmd_ring, false);
}
static void handle_vendor_event(struct xhci_hcd *xhci,
union xhci_trb *event)
{
u32 trb_type;
trb_type = TRB_FIELD_TO_TYPE(le32_to_cpu(event->generic.field[3]));
xhci_dbg(xhci, "Vendor specific event TRB type = %u\n", trb_type);
if (trb_type == TRB_NEC_CMD_COMP && (xhci->quirks & XHCI_NEC_HOST))
handle_cmd_completion(xhci, &event->event_cmd);
}
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
/* @port_id: the one-based port ID from the hardware (indexed from array of all
* port registers -- USB 3.0 and USB 2.0).
*
* Returns a zero-based port number, which is suitable for indexing into each of
* the split roothubs' port arrays and bus state arrays.
*/
static unsigned int find_faked_portnum_from_hw_portnum(struct usb_hcd *hcd,
struct xhci_hcd *xhci, u32 port_id)
{
unsigned int i;
unsigned int num_similar_speed_ports = 0;
/* port_id from the hardware is 1-based, but port_array[], usb3_ports[],
* and usb2_ports are 0-based indexes. Count the number of similar
* speed ports, up to 1 port before this port.
*/
for (i = 0; i < (port_id - 1); i++) {
u8 port_speed = xhci->port_array[i];
/*
* Skip ports that don't have known speeds, or have duplicate
* Extended Capabilities port speed entries.
*/
if (port_speed == 0 || port_speed == DUPLICATE_ENTRY)
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
continue;
/*
* USB 3.0 ports are always under a USB 3.0 hub. USB 2.0 and
* 1.1 ports are under the USB 2.0 hub. If the port speed
* matches the device speed, it's a similar speed port.
*/
if ((port_speed == 0x03) == (hcd->speed == HCD_USB3))
num_similar_speed_ports++;
}
return num_similar_speed_ports;
}
static void handle_port_status(struct xhci_hcd *xhci,
union xhci_trb *event)
{
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
struct usb_hcd *hcd;
u32 port_id;
u32 temp, temp1;
int max_ports;
int slot_id;
unsigned int faked_port_index;
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
u8 major_revision;
struct xhci_bus_state *bus_state;
__le32 __iomem **port_array;
bool bogus_port_status = false;
/* Port status change events always have a successful completion code */
if (GET_COMP_CODE(le32_to_cpu(event->generic.field[2])) != COMP_SUCCESS) {
xhci_warn(xhci, "WARN: xHC returned failed port status event\n");
xhci->error_bitmask |= 1 << 8;
}
port_id = GET_PORT_ID(le32_to_cpu(event->generic.field[0]));
xhci_dbg(xhci, "Port Status Change Event for port %d\n", port_id);
max_ports = HCS_MAX_PORTS(xhci->hcs_params1);
if ((port_id <= 0) || (port_id > max_ports)) {
xhci_warn(xhci, "Invalid port id %d\n", port_id);
bogus_port_status = true;
goto cleanup;
}
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
/* Figure out which usb_hcd this port is attached to:
* is it a USB 3.0 port or a USB 2.0/1.1 port?
*/
major_revision = xhci->port_array[port_id - 1];
if (major_revision == 0) {
xhci_warn(xhci, "Event for port %u not in "
"Extended Capabilities, ignoring.\n",
port_id);
bogus_port_status = true;
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
goto cleanup;
}
if (major_revision == DUPLICATE_ENTRY) {
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
xhci_warn(xhci, "Event for port %u duplicated in"
"Extended Capabilities, ignoring.\n",
port_id);
bogus_port_status = true;
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
goto cleanup;
}
/*
* Hardware port IDs reported by a Port Status Change Event include USB
* 3.0 and USB 2.0 ports. We want to check if the port has reported a
* resume event, but we first need to translate the hardware port ID
* into the index into the ports on the correct split roothub, and the
* correct bus_state structure.
*/
/* Find the right roothub. */
hcd = xhci_to_hcd(xhci);
if ((major_revision == 0x03) != (hcd->speed == HCD_USB3))
hcd = xhci->shared_hcd;
bus_state = &xhci->bus_state[hcd_index(hcd)];
if (hcd->speed == HCD_USB3)
port_array = xhci->usb3_ports;
else
port_array = xhci->usb2_ports;
/* Find the faked port hub number */
faked_port_index = find_faked_portnum_from_hw_portnum(hcd, xhci,
port_id);
temp = xhci_readl(xhci, port_array[faked_port_index]);
if (hcd->state == HC_STATE_SUSPENDED) {
xhci_dbg(xhci, "resume root hub\n");
usb_hcd_resume_root_hub(hcd);
}
if ((temp & PORT_PLC) && (temp & PORT_PLS_MASK) == XDEV_RESUME) {
xhci_dbg(xhci, "port resume event for port %d\n", port_id);
temp1 = xhci_readl(xhci, &xhci->op_regs->command);
if (!(temp1 & CMD_RUN)) {
xhci_warn(xhci, "xHC is not running.\n");
goto cleanup;
}
if (DEV_SUPERSPEED(temp)) {
xhci_dbg(xhci, "resume SS port %d\n", port_id);
temp = xhci_port_state_to_neutral(temp);
temp &= ~PORT_PLS_MASK;
temp |= PORT_LINK_STROBE | XDEV_U0;
xhci_writel(xhci, temp, port_array[faked_port_index]);
slot_id = xhci_find_slot_id_by_port(hcd, xhci,
faked_port_index);
if (!slot_id) {
xhci_dbg(xhci, "slot_id is zero\n");
goto cleanup;
}
xhci_ring_device(xhci, slot_id);
xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
/* Clear PORT_PLC */
temp = xhci_readl(xhci, port_array[faked_port_index]);
temp = xhci_port_state_to_neutral(temp);
temp |= PORT_PLC;
xhci_writel(xhci, temp, port_array[faked_port_index]);
} else {
xhci_dbg(xhci, "resume HS port %d\n", port_id);
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
bus_state->resume_done[faked_port_index] = jiffies +
msecs_to_jiffies(20);
mod_timer(&hcd->rh_timer,
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
bus_state->resume_done[faked_port_index]);
/* Do the rest in GetPortStatus */
}
}
cleanup:
/* Update event ring dequeue pointer before dropping the lock */
inc_deq(xhci, xhci->event_ring, true);
/* Don't make the USB core poll the roothub if we got a bad port status
* change event. Besides, at that point we can't tell which roothub
* (USB 2.0 or USB 3.0) to kick.
*/
if (bogus_port_status)
return;
spin_unlock(&xhci->lock);
/* Pass this up to the core */
xhci: Register second xHCI roothub. This patch changes the xHCI driver to allocate two roothubs. This touches the driver initialization and shutdown paths, roothub emulation code, and port status change event handlers. This is a rather large patch, but it can't be broken up, or it would break git-bisect. Make the xHCI driver register its own PCI probe function. This will call the USB core to create the USB 2.0 roothub, and then create the USB 3.0 roothub. This gets the code for registering a shared roothub out of the USB core, and allows other HCDs later to decide if and how many shared roothubs they want to allocate. Make sure the xHCI's reset method marks the xHCI host controller's primary roothub as the USB 2.0 roothub. This ensures that the high speed bus will be processed first when the PCI device is resumed, and any USB 3.0 devices that have migrated over to high speed will migrate back after being reset. This ensures that USB persist works with these odd devices. The reset method will also mark the xHCI USB2 roothub as having an integrated TT. Like EHCI host controllers with a "rate matching hub" the xHCI USB 2.0 roothub doesn't have an OHCI or UHCI companion controller. It doesn't really have a TT, but we'll lie and say it has an integrated TT. We need to do this because the USB core will reject LS/FS devices under a HS hub without a TT. Other details: ------------- The roothub emulation code is changed to return the correct number of ports for the two roothubs. For the USB 3.0 roothub, it only reports the USB 3.0 ports. For the USB 2.0 roothub, it reports all the LS/FS/HS ports. The code to disable a port now checks the speed of the roothub, and refuses to disable SuperSpeed ports under the USB 3.0 roothub. The code for initializing a new device context must be changed to set the proper roothub port number. Since we've split the xHCI host into two roothubs, we can't just use the port number in the ancestor hub. Instead, we loop through the array of hardware port status register speeds and find the Nth port with a similar speed. The port status change event handler is updated to figure out whether the port that reported the change is a USB 3.0 port, or a non-SuperSpeed port. Once it figures out the port speed, it kicks the proper roothub. The function to find a slot ID based on the port index is updated to take into account that the two roothubs will have over-lapping port indexes. It checks that the virtual device with a matching port index is the same speed as the passed in roothub. There's also changes to the driver initialization and shutdown paths: 1. Make sure that the xhci_hcd pointer is shared across the two usb_hcd structures. The xhci_hcd pointer is allocated and the registers are mapped in when xhci_pci_setup() is called with the primary HCD. When xhci_pci_setup() is called with the non-primary HCD, the xhci_hcd pointer is stored. 2. Make sure to set the sg_tablesize for both usb_hcd structures. Set the PCI DMA mask for the non-primary HCD to allow for 64-bit or 32-bit DMA. (The PCI DMA mask is set from the primary HCD further down in the xhci_pci_setup() function.) 3. Ensure that the host controller doesn't start kicking khubd in response to port status changes before both usb_hcd structures are registered. xhci_run() only starts the xHC running once it has been called with the non-primary roothub. Similarly, the xhci_stop() function only halts the host controller when it is called with the non-primary HCD. Then on the second call, it resets and cleans up the MSI-X irqs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2010-12-16 19:21:10 +00:00
usb_hcd_poll_rh_status(hcd);
spin_lock(&xhci->lock);
}
/*
* This TD is defined by the TRBs starting at start_trb in start_seg and ending
* at end_trb, which may be in another segment. If the suspect DMA address is a
* TRB in this TD, this function returns that TRB's segment. Otherwise it
* returns 0.
*/
struct xhci_segment *trb_in_td(struct xhci_segment *start_seg,
union xhci_trb *start_trb,
union xhci_trb *end_trb,
dma_addr_t suspect_dma)
{
dma_addr_t start_dma;
dma_addr_t end_seg_dma;
dma_addr_t end_trb_dma;
struct xhci_segment *cur_seg;
start_dma = xhci_trb_virt_to_dma(start_seg, start_trb);
cur_seg = start_seg;
do {
if (start_dma == 0)
USB: clean up some host controller sparse warnings Fix usb sparse warnings: drivers/usb/host/isp1362-hcd.c:2220:50: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:43:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:49:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:161:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:198:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:319:31: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:1231:33: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-pci.c:177:23: warning: non-ANSI function declaration of function 'xhci_register_pci' drivers/usb/host/xhci-pci.c:182:26: warning: non-ANSI function declaration of function 'xhci_unregister_pci' drivers/usb/host/xhci-ring.c:342:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:525:34: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1009:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1031:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1041:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1096:30: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1100:27: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:224:27: warning: symbol 'xhci_alloc_container_ctx' was not declared. Should it be static? drivers/usb/host/xhci-mem.c:242:6: warning: symbol 'xhci_free_container_ctx' was not declared. Should it be static? Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off By: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-19 15:53:50 +00:00
return NULL;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* We may get an event for a Link TRB in the middle of a TD */
end_seg_dma = xhci_trb_virt_to_dma(cur_seg,
&cur_seg->trbs[TRBS_PER_SEGMENT - 1]);
/* If the end TRB isn't in this segment, this is set to 0 */
end_trb_dma = xhci_trb_virt_to_dma(cur_seg, end_trb);
if (end_trb_dma > 0) {
/* The end TRB is in this segment, so suspect should be here */
if (start_dma <= end_trb_dma) {
if (suspect_dma >= start_dma && suspect_dma <= end_trb_dma)
return cur_seg;
} else {
/* Case for one segment with
* a TD wrapped around to the top
*/
if ((suspect_dma >= start_dma &&
suspect_dma <= end_seg_dma) ||
(suspect_dma >= cur_seg->dma &&
suspect_dma <= end_trb_dma))
return cur_seg;
}
USB: clean up some host controller sparse warnings Fix usb sparse warnings: drivers/usb/host/isp1362-hcd.c:2220:50: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:43:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:49:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:161:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:198:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:319:31: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:1231:33: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-pci.c:177:23: warning: non-ANSI function declaration of function 'xhci_register_pci' drivers/usb/host/xhci-pci.c:182:26: warning: non-ANSI function declaration of function 'xhci_unregister_pci' drivers/usb/host/xhci-ring.c:342:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:525:34: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1009:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1031:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1041:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1096:30: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1100:27: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:224:27: warning: symbol 'xhci_alloc_container_ctx' was not declared. Should it be static? drivers/usb/host/xhci-mem.c:242:6: warning: symbol 'xhci_free_container_ctx' was not declared. Should it be static? Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off By: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-19 15:53:50 +00:00
return NULL;
} else {
/* Might still be somewhere in this segment */
if (suspect_dma >= start_dma && suspect_dma <= end_seg_dma)
return cur_seg;
}
cur_seg = cur_seg->next;
start_dma = xhci_trb_virt_to_dma(cur_seg, &cur_seg->trbs[0]);
} while (cur_seg != start_seg);
USB: clean up some host controller sparse warnings Fix usb sparse warnings: drivers/usb/host/isp1362-hcd.c:2220:50: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:43:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:49:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:161:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:198:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:319:31: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:1231:33: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-pci.c:177:23: warning: non-ANSI function declaration of function 'xhci_register_pci' drivers/usb/host/xhci-pci.c:182:26: warning: non-ANSI function declaration of function 'xhci_unregister_pci' drivers/usb/host/xhci-ring.c:342:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:525:34: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1009:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1031:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1041:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1096:30: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1100:27: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:224:27: warning: symbol 'xhci_alloc_container_ctx' was not declared. Should it be static? drivers/usb/host/xhci-mem.c:242:6: warning: symbol 'xhci_free_container_ctx' was not declared. Should it be static? Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off By: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-19 15:53:50 +00:00
return NULL;
}
static void xhci_cleanup_halted_endpoint(struct xhci_hcd *xhci,
unsigned int slot_id, unsigned int ep_index,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int stream_id,
struct xhci_td *td, union xhci_trb *event_trb)
{
struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index];
ep->ep_state |= EP_HALTED;
ep->stopped_td = td;
ep->stopped_trb = event_trb;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep->stopped_stream = stream_id;
xhci_queue_reset_ep(xhci, slot_id, ep_index);
xhci_cleanup_stalled_ring(xhci, td->urb->dev, ep_index);
ep->stopped_td = NULL;
ep->stopped_trb = NULL;
ep->stopped_stream = 0;
xhci_ring_cmd_db(xhci);
}
/* Check if an error has halted the endpoint ring. The class driver will
* cleanup the halt for a non-default control endpoint if we indicate a stall.
* However, a babble and other errors also halt the endpoint ring, and the class
* driver won't clear the halt in that case, so we need to issue a Set Transfer
* Ring Dequeue Pointer command manually.
*/
static int xhci_requires_manual_halt_cleanup(struct xhci_hcd *xhci,
struct xhci_ep_ctx *ep_ctx,
unsigned int trb_comp_code)
{
/* TRB completion codes that may require a manual halt cleanup */
if (trb_comp_code == COMP_TX_ERR ||
trb_comp_code == COMP_BABBLE ||
trb_comp_code == COMP_SPLIT_ERR)
/* The 0.96 spec says a babbling control endpoint
* is not halted. The 0.96 spec says it is. Some HW
* claims to be 0.95 compliant, but it halts the control
* endpoint anyway. Check if a babble halted the
* endpoint.
*/
if ((le32_to_cpu(ep_ctx->ep_info) & EP_STATE_MASK) == EP_STATE_HALTED)
return 1;
return 0;
}
int xhci_is_vendor_info_code(struct xhci_hcd *xhci, unsigned int trb_comp_code)
{
if (trb_comp_code >= 224 && trb_comp_code <= 255) {
/* Vendor defined "informational" completion code,
* treat as not-an-error.
*/
xhci_dbg(xhci, "Vendor defined info completion code %u\n",
trb_comp_code);
xhci_dbg(xhci, "Treating code as success.\n");
return 1;
}
return 0;
}
/*
* Finish the td processing, remove the td from td list;
* Return 1 if the urb can be given back.
*/
static int finish_td(struct xhci_hcd *xhci, struct xhci_td *td,
union xhci_trb *event_trb, struct xhci_transfer_event *event,
struct xhci_virt_ep *ep, int *status, bool skip)
{
struct xhci_virt_device *xdev;
struct xhci_ring *ep_ring;
unsigned int slot_id;
int ep_index;
struct urb *urb = NULL;
struct xhci_ep_ctx *ep_ctx;
int ret = 0;
struct urb_priv *urb_priv;
u32 trb_comp_code;
slot_id = TRB_TO_SLOT_ID(le32_to_cpu(event->flags));
xdev = xhci->devs[slot_id];
ep_index = TRB_TO_EP_ID(le32_to_cpu(event->flags)) - 1;
ep_ring = xhci_dma_to_transfer_ring(ep, le64_to_cpu(event->buffer));
ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
if (skip)
goto td_cleanup;
if (trb_comp_code == COMP_STOP_INVAL ||
trb_comp_code == COMP_STOP) {
/* The Endpoint Stop Command completion will take care of any
* stopped TDs. A stopped TD may be restarted, so don't update
* the ring dequeue pointer or take this TD off any lists yet.
*/
ep->stopped_td = td;
ep->stopped_trb = event_trb;
return 0;
} else {
if (trb_comp_code == COMP_STALL) {
/* The transfer is completed from the driver's
* perspective, but we need to issue a set dequeue
* command for this stalled endpoint to move the dequeue
* pointer past the TD. We can't do that here because
* the halt condition must be cleared first. Let the
* USB class driver clear the stall later.
*/
ep->stopped_td = td;
ep->stopped_trb = event_trb;
ep->stopped_stream = ep_ring->stream_id;
} else if (xhci_requires_manual_halt_cleanup(xhci,
ep_ctx, trb_comp_code)) {
/* Other types of errors halt the endpoint, but the
* class driver doesn't call usb_reset_endpoint() unless
* the error is -EPIPE. Clear the halted status in the
* xHCI hardware manually.
*/
xhci_cleanup_halted_endpoint(xhci,
slot_id, ep_index, ep_ring->stream_id,
td, event_trb);
} else {
/* Update ring dequeue pointer */
while (ep_ring->dequeue != td->last_trb)
inc_deq(xhci, ep_ring, false);
inc_deq(xhci, ep_ring, false);
}
td_cleanup:
/* Clean up the endpoint's TD list */
urb = td->urb;
urb_priv = urb->hcpriv;
/* Do one last check of the actual transfer length.
* If the host controller said we transferred more data than
* the buffer length, urb->actual_length will be a very big
* number (since it's unsigned). Play it safe and say we didn't
* transfer anything.
*/
if (urb->actual_length > urb->transfer_buffer_length) {
xhci_warn(xhci, "URB transfer length is wrong, "
"xHC issue? req. len = %u, "
"act. len = %u\n",
urb->transfer_buffer_length,
urb->actual_length);
urb->actual_length = 0;
if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
*status = -EREMOTEIO;
else
*status = 0;
}
list_del(&td->td_list);
/* Was this TD slated to be cancelled but completed anyway? */
if (!list_empty(&td->cancelled_td_list))
list_del(&td->cancelled_td_list);
urb_priv->td_cnt++;
/* Giveback the urb when all the tds are completed */
if (urb_priv->td_cnt == urb_priv->length) {
ret = 1;
if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) {
xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs--;
if (xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs
== 0) {
if (xhci->quirks & XHCI_AMD_PLL_FIX)
usb_amd_quirk_pll_enable();
}
}
}
}
return ret;
}
/*
* Process control tds, update urb status and actual_length.
*/
static int process_ctrl_td(struct xhci_hcd *xhci, struct xhci_td *td,
union xhci_trb *event_trb, struct xhci_transfer_event *event,
struct xhci_virt_ep *ep, int *status)
{
struct xhci_virt_device *xdev;
struct xhci_ring *ep_ring;
unsigned int slot_id;
int ep_index;
struct xhci_ep_ctx *ep_ctx;
u32 trb_comp_code;
slot_id = TRB_TO_SLOT_ID(le32_to_cpu(event->flags));
xdev = xhci->devs[slot_id];
ep_index = TRB_TO_EP_ID(le32_to_cpu(event->flags)) - 1;
ep_ring = xhci_dma_to_transfer_ring(ep, le64_to_cpu(event->buffer));
ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
xhci_debug_trb(xhci, xhci->event_ring->dequeue);
switch (trb_comp_code) {
case COMP_SUCCESS:
if (event_trb == ep_ring->dequeue) {
xhci_warn(xhci, "WARN: Success on ctrl setup TRB "
"without IOC set??\n");
*status = -ESHUTDOWN;
} else if (event_trb != td->last_trb) {
xhci_warn(xhci, "WARN: Success on ctrl data TRB "
"without IOC set??\n");
*status = -ESHUTDOWN;
} else {
xhci_dbg(xhci, "Successful control transfer!\n");
*status = 0;
}
break;
case COMP_SHORT_TX:
xhci_warn(xhci, "WARN: short transfer on control ep\n");
if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
*status = -EREMOTEIO;
else
*status = 0;
break;
xhci: Fix bug in control transfer cancellation. When the xHCI driver attempts to cancel a transfer, it issues a Stop Endpoint command and waits for the host controller to indicate which TRB it was in the middle of processing. The host will put an event TRB with completion code COMP_STOP on the event ring if it stops on a control transfer TRB (or other types of transfer TRBs). The ring handling code is supposed to set ep->stopped_trb to the TRB that the host stopped on when this happens. Unfortunately, there is a long-standing bug in the control transfer completion code. It doesn't actually check to see if COMP_STOP is set before attempting to process the transfer based on which part of the control TD completed. So when we get an event on the data phase of the control TRB with COMP_STOP set, it thinks it's a normal completion of the transfer and doesn't set ep->stopped_td or ep->stopped_trb. When the ring handling code goes on to process the completion of the Stop Endpoint command, it sees that ep->stopped_trb is not a part of the TD it's trying to cancel. It thinks the hardware has its enqueue pointer somewhere further up in the ring, and thinks it's safe to turn the control TRBs into no-op TRBs. Since the hardware was in the middle of the control TRBs to be cancelled, the proper software behavior is to issue a Set TR dequeue pointer command. It turns out that the NEC host controllers can handle active TRBs being set to no-op TRBs after a stop endpoint command, but other host controllers have issues with this out-of-spec software behavior. Fix this behavior. This patch should be backported to kernels as far back as 2.6.31, but it may be a bit challenging, since process_ctrl_td() was introduced in some refactoring done in 2.6.36, and some endian-safe patches added in 2.6.40 that touch the same lines. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: stable@kernel.org
2011-05-06 02:08:09 +00:00
case COMP_STOP_INVAL:
case COMP_STOP:
return finish_td(xhci, td, event_trb, event, ep, status, false);
default:
if (!xhci_requires_manual_halt_cleanup(xhci,
ep_ctx, trb_comp_code))
break;
xhci_dbg(xhci, "TRB error code %u, "
"halted endpoint index = %u\n",
trb_comp_code, ep_index);
/* else fall through */
case COMP_STALL:
/* Did we transfer part of the data (middle) phase? */
if (event_trb != ep_ring->dequeue &&
event_trb != td->last_trb)
td->urb->actual_length =
td->urb->transfer_buffer_length
- TRB_LEN(le32_to_cpu(event->transfer_len));
else
td->urb->actual_length = 0;
xhci_cleanup_halted_endpoint(xhci,
slot_id, ep_index, 0, td, event_trb);
return finish_td(xhci, td, event_trb, event, ep, status, true);
}
/*
* Did we transfer any data, despite the errors that might have
* happened? I.e. did we get past the setup stage?
*/
if (event_trb != ep_ring->dequeue) {
/* The event was for the status stage */
if (event_trb == td->last_trb) {
if (td->urb->actual_length != 0) {
/* Don't overwrite a previously set error code
*/
if ((*status == -EINPROGRESS || *status == 0) &&
(td->urb->transfer_flags
& URB_SHORT_NOT_OK))
/* Did we already see a short data
* stage? */
*status = -EREMOTEIO;
} else {
td->urb->actual_length =
td->urb->transfer_buffer_length;
}
} else {
/* Maybe the event was for the data stage? */
xhci: Fix bug in control transfer cancellation. When the xHCI driver attempts to cancel a transfer, it issues a Stop Endpoint command and waits for the host controller to indicate which TRB it was in the middle of processing. The host will put an event TRB with completion code COMP_STOP on the event ring if it stops on a control transfer TRB (or other types of transfer TRBs). The ring handling code is supposed to set ep->stopped_trb to the TRB that the host stopped on when this happens. Unfortunately, there is a long-standing bug in the control transfer completion code. It doesn't actually check to see if COMP_STOP is set before attempting to process the transfer based on which part of the control TD completed. So when we get an event on the data phase of the control TRB with COMP_STOP set, it thinks it's a normal completion of the transfer and doesn't set ep->stopped_td or ep->stopped_trb. When the ring handling code goes on to process the completion of the Stop Endpoint command, it sees that ep->stopped_trb is not a part of the TD it's trying to cancel. It thinks the hardware has its enqueue pointer somewhere further up in the ring, and thinks it's safe to turn the control TRBs into no-op TRBs. Since the hardware was in the middle of the control TRBs to be cancelled, the proper software behavior is to issue a Set TR dequeue pointer command. It turns out that the NEC host controllers can handle active TRBs being set to no-op TRBs after a stop endpoint command, but other host controllers have issues with this out-of-spec software behavior. Fix this behavior. This patch should be backported to kernels as far back as 2.6.31, but it may be a bit challenging, since process_ctrl_td() was introduced in some refactoring done in 2.6.36, and some endian-safe patches added in 2.6.40 that touch the same lines. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: stable@kernel.org
2011-05-06 02:08:09 +00:00
td->urb->actual_length =
td->urb->transfer_buffer_length -
TRB_LEN(le32_to_cpu(event->transfer_len));
xhci_dbg(xhci, "Waiting for status "
"stage event\n");
return 0;
}
}
return finish_td(xhci, td, event_trb, event, ep, status, false);
}
/*
* Process isochronous tds, update urb packet status and actual_length.
*/
static int process_isoc_td(struct xhci_hcd *xhci, struct xhci_td *td,
union xhci_trb *event_trb, struct xhci_transfer_event *event,
struct xhci_virt_ep *ep, int *status)
{
struct xhci_ring *ep_ring;
struct urb_priv *urb_priv;
int idx;
int len = 0;
union xhci_trb *cur_trb;
struct xhci_segment *cur_seg;
struct usb_iso_packet_descriptor *frame;
u32 trb_comp_code;
bool skip_td = false;
ep_ring = xhci_dma_to_transfer_ring(ep, le64_to_cpu(event->buffer));
trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
urb_priv = td->urb->hcpriv;
idx = urb_priv->td_cnt;
frame = &td->urb->iso_frame_desc[idx];
/* handle completion code */
switch (trb_comp_code) {
case COMP_SUCCESS:
frame->status = 0;
xhci_dbg(xhci, "Successful isoc transfer!\n");
break;
case COMP_SHORT_TX:
frame->status = td->urb->transfer_flags & URB_SHORT_NOT_OK ?
-EREMOTEIO : 0;
break;
case COMP_BW_OVER:
frame->status = -ECOMM;
skip_td = true;
break;
case COMP_BUFF_OVER:
case COMP_BABBLE:
frame->status = -EOVERFLOW;
skip_td = true;
break;
case COMP_STALL:
frame->status = -EPROTO;
skip_td = true;
break;
case COMP_STOP:
case COMP_STOP_INVAL:
break;
default:
frame->status = -1;
break;
}
if (trb_comp_code == COMP_SUCCESS || skip_td) {
frame->actual_length = frame->length;
td->urb->actual_length += frame->length;
} else {
for (cur_trb = ep_ring->dequeue,
cur_seg = ep_ring->deq_seg; cur_trb != event_trb;
next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) {
if ((le32_to_cpu(cur_trb->generic.field[3]) &
TRB_TYPE_BITMASK) != TRB_TYPE(TRB_TR_NOOP) &&
(le32_to_cpu(cur_trb->generic.field[3]) &
TRB_TYPE_BITMASK) != TRB_TYPE(TRB_LINK))
len += TRB_LEN(le32_to_cpu(cur_trb->generic.field[2]));
}
len += TRB_LEN(le32_to_cpu(cur_trb->generic.field[2])) -
TRB_LEN(le32_to_cpu(event->transfer_len));
if (trb_comp_code != COMP_STOP_INVAL) {
frame->actual_length = len;
td->urb->actual_length += len;
}
}
if ((idx == urb_priv->length - 1) && *status == -EINPROGRESS)
*status = 0;
return finish_td(xhci, td, event_trb, event, ep, status, false);
}
static int skip_isoc_td(struct xhci_hcd *xhci, struct xhci_td *td,
struct xhci_transfer_event *event,
struct xhci_virt_ep *ep, int *status)
{
struct xhci_ring *ep_ring;
struct urb_priv *urb_priv;
struct usb_iso_packet_descriptor *frame;
int idx;
ep_ring = xhci_dma_to_transfer_ring(ep, event->buffer);
urb_priv = td->urb->hcpriv;
idx = urb_priv->td_cnt;
frame = &td->urb->iso_frame_desc[idx];
/* The transfer is partly done */
*status = -EXDEV;
frame->status = -EXDEV;
/* calc actual length */
frame->actual_length = 0;
/* Update ring dequeue pointer */
while (ep_ring->dequeue != td->last_trb)
inc_deq(xhci, ep_ring, false);
inc_deq(xhci, ep_ring, false);
return finish_td(xhci, td, NULL, event, ep, status, true);
}
/*
* Process bulk and interrupt tds, update urb status and actual_length.
*/
static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_td *td,
union xhci_trb *event_trb, struct xhci_transfer_event *event,
struct xhci_virt_ep *ep, int *status)
{
struct xhci_ring *ep_ring;
union xhci_trb *cur_trb;
struct xhci_segment *cur_seg;
u32 trb_comp_code;
ep_ring = xhci_dma_to_transfer_ring(ep, le64_to_cpu(event->buffer));
trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
switch (trb_comp_code) {
case COMP_SUCCESS:
/* Double check that the HW transferred everything. */
if (event_trb != td->last_trb) {
xhci_warn(xhci, "WARN Successful completion "
"on short TX\n");
if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
*status = -EREMOTEIO;
else
*status = 0;
} else {
if (usb_endpoint_xfer_bulk(&td->urb->ep->desc))
xhci_dbg(xhci, "Successful bulk "
"transfer!\n");
else
xhci_dbg(xhci, "Successful interrupt "
"transfer!\n");
*status = 0;
}
break;
case COMP_SHORT_TX:
if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
*status = -EREMOTEIO;
else
*status = 0;
break;
default:
/* Others already handled above */
break;
}
xhci_dbg(xhci, "ep %#x - asked for %d bytes, "
"%d bytes untransferred\n",
td->urb->ep->desc.bEndpointAddress,
td->urb->transfer_buffer_length,
TRB_LEN(le32_to_cpu(event->transfer_len)));
/* Fast path - was this the last TRB in the TD for this URB? */
if (event_trb == td->last_trb) {
if (TRB_LEN(le32_to_cpu(event->transfer_len)) != 0) {
td->urb->actual_length =
td->urb->transfer_buffer_length -
TRB_LEN(le32_to_cpu(event->transfer_len));
if (td->urb->transfer_buffer_length <
td->urb->actual_length) {
xhci_warn(xhci, "HC gave bad length "
"of %d bytes left\n",
TRB_LEN(le32_to_cpu(event->transfer_len)));
td->urb->actual_length = 0;
if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
*status = -EREMOTEIO;
else
*status = 0;
}
/* Don't overwrite a previously set error code */
if (*status == -EINPROGRESS) {
if (td->urb->transfer_flags & URB_SHORT_NOT_OK)
*status = -EREMOTEIO;
else
*status = 0;
}
} else {
td->urb->actual_length =
td->urb->transfer_buffer_length;
/* Ignore a short packet completion if the
* untransferred length was zero.
*/
if (*status == -EREMOTEIO)
*status = 0;
}
} else {
/* Slow path - walk the list, starting from the dequeue
* pointer, to get the actual length transferred.
*/
td->urb->actual_length = 0;
for (cur_trb = ep_ring->dequeue, cur_seg = ep_ring->deq_seg;
cur_trb != event_trb;
next_trb(xhci, ep_ring, &cur_seg, &cur_trb)) {
if ((le32_to_cpu(cur_trb->generic.field[3]) &
TRB_TYPE_BITMASK) != TRB_TYPE(TRB_TR_NOOP) &&
(le32_to_cpu(cur_trb->generic.field[3]) &
TRB_TYPE_BITMASK) != TRB_TYPE(TRB_LINK))
td->urb->actual_length +=
TRB_LEN(le32_to_cpu(cur_trb->generic.field[2]));
}
/* If the ring didn't stop on a Link or No-op TRB, add
* in the actual bytes transferred from the Normal TRB
*/
if (trb_comp_code != COMP_STOP_INVAL)
td->urb->actual_length +=
TRB_LEN(le32_to_cpu(cur_trb->generic.field[2])) -
TRB_LEN(le32_to_cpu(event->transfer_len));
}
return finish_td(xhci, td, event_trb, event, ep, status, false);
}
/*
* If this function returns an error condition, it means it got a Transfer
* event with a corrupted Slot ID, Endpoint ID, or TRB DMA address.
* At this point, the host controller is probably hosed and should be reset.
*/
static int handle_tx_event(struct xhci_hcd *xhci,
struct xhci_transfer_event *event)
{
struct xhci_virt_device *xdev;
struct xhci_virt_ep *ep;
struct xhci_ring *ep_ring;
unsigned int slot_id;
int ep_index;
USB: clean up some host controller sparse warnings Fix usb sparse warnings: drivers/usb/host/isp1362-hcd.c:2220:50: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:43:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:49:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:161:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:198:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:319:31: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:1231:33: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-pci.c:177:23: warning: non-ANSI function declaration of function 'xhci_register_pci' drivers/usb/host/xhci-pci.c:182:26: warning: non-ANSI function declaration of function 'xhci_unregister_pci' drivers/usb/host/xhci-ring.c:342:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:525:34: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1009:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1031:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1041:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1096:30: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1100:27: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:224:27: warning: symbol 'xhci_alloc_container_ctx' was not declared. Should it be static? drivers/usb/host/xhci-mem.c:242:6: warning: symbol 'xhci_free_container_ctx' was not declared. Should it be static? Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off By: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-19 15:53:50 +00:00
struct xhci_td *td = NULL;
dma_addr_t event_dma;
struct xhci_segment *event_seg;
union xhci_trb *event_trb;
USB: clean up some host controller sparse warnings Fix usb sparse warnings: drivers/usb/host/isp1362-hcd.c:2220:50: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:43:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:49:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:161:24: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:198:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:319:31: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:1231:33: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-pci.c:177:23: warning: non-ANSI function declaration of function 'xhci_register_pci' drivers/usb/host/xhci-pci.c:182:26: warning: non-ANSI function declaration of function 'xhci_unregister_pci' drivers/usb/host/xhci-ring.c:342:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:525:34: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1009:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1031:32: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1041:16: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1096:30: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-ring.c:1100:27: warning: Using plain integer as NULL pointer drivers/usb/host/xhci-mem.c:224:27: warning: symbol 'xhci_alloc_container_ctx' was not declared. Should it be static? drivers/usb/host/xhci-mem.c:242:6: warning: symbol 'xhci_free_container_ctx' was not declared. Should it be static? Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Cc: Lothar Wassmann <LW@KARO-electronics.de> Signed-off By: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-19 15:53:50 +00:00
struct urb *urb = NULL;
int status = -EINPROGRESS;
struct urb_priv *urb_priv;
struct xhci_ep_ctx *ep_ctx;
u32 trb_comp_code;
int ret = 0;
slot_id = TRB_TO_SLOT_ID(le32_to_cpu(event->flags));
xdev = xhci->devs[slot_id];
if (!xdev) {
xhci_err(xhci, "ERROR Transfer event pointed to bad slot\n");
return -ENODEV;
}
/* Endpoint ID is 1 based, our index is zero based */
ep_index = TRB_TO_EP_ID(le32_to_cpu(event->flags)) - 1;
xhci_dbg(xhci, "%s - ep index = %d\n", __func__, ep_index);
ep = &xdev->eps[ep_index];
ep_ring = xhci_dma_to_transfer_ring(ep, le64_to_cpu(event->buffer));
ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
if (!ep_ring ||
(le32_to_cpu(ep_ctx->ep_info) & EP_STATE_MASK) ==
EP_STATE_DISABLED) {
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
xhci_err(xhci, "ERROR Transfer event for disabled endpoint "
"or incorrect stream ring\n");
return -ENODEV;
}
event_dma = le64_to_cpu(event->buffer);
trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len));
/* Look for common error cases */
switch (trb_comp_code) {
/* Skip codes that require special handling depending on
* transfer type
*/
case COMP_SUCCESS:
case COMP_SHORT_TX:
break;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
case COMP_STOP:
xhci_dbg(xhci, "Stopped on Transfer TRB\n");
break;
case COMP_STOP_INVAL:
xhci_dbg(xhci, "Stopped on No-op or Link TRB\n");
break;
case COMP_STALL:
xhci_warn(xhci, "WARN: Stalled endpoint\n");
ep->ep_state |= EP_HALTED;
status = -EPIPE;
break;
case COMP_TRB_ERR:
xhci_warn(xhci, "WARN: TRB error on endpoint\n");
status = -EILSEQ;
break;
case COMP_SPLIT_ERR:
case COMP_TX_ERR:
xhci_warn(xhci, "WARN: transfer error on endpoint\n");
status = -EPROTO;
break;
case COMP_BABBLE:
xhci_warn(xhci, "WARN: babble error on endpoint\n");
status = -EOVERFLOW;
break;
case COMP_DB_ERR:
xhci_warn(xhci, "WARN: HC couldn't access mem fast enough\n");
status = -ENOSR;
break;
case COMP_BW_OVER:
xhci_warn(xhci, "WARN: bandwidth overrun event on endpoint\n");
break;
case COMP_BUFF_OVER:
xhci_warn(xhci, "WARN: buffer overrun event on endpoint\n");
break;
case COMP_UNDERRUN:
/*
* When the Isoch ring is empty, the xHC will generate
* a Ring Overrun Event for IN Isoch endpoint or Ring
* Underrun Event for OUT Isoch endpoint.
*/
xhci_dbg(xhci, "underrun event on endpoint\n");
if (!list_empty(&ep_ring->td_list))
xhci_dbg(xhci, "Underrun Event for slot %d ep %d "
"still with TDs queued?\n",
TRB_TO_SLOT_ID(le32_to_cpu(event->flags)),
ep_index);
goto cleanup;
case COMP_OVERRUN:
xhci_dbg(xhci, "overrun event on endpoint\n");
if (!list_empty(&ep_ring->td_list))
xhci_dbg(xhci, "Overrun Event for slot %d ep %d "
"still with TDs queued?\n",
TRB_TO_SLOT_ID(le32_to_cpu(event->flags)),
ep_index);
goto cleanup;
case COMP_MISSED_INT:
/*
* When encounter missed service error, one or more isoc tds
* may be missed by xHC.
* Set skip flag of the ep_ring; Complete the missed tds as
* short transfer when process the ep_ring next time.
*/
ep->skip = true;
xhci_dbg(xhci, "Miss service interval error, set skip flag\n");
goto cleanup;
default:
if (xhci_is_vendor_info_code(xhci, trb_comp_code)) {
status = 0;
break;
}
xhci_warn(xhci, "ERROR Unknown event condition, HC probably "
"busted\n");
goto cleanup;
}
do {
/* This TRB should be in the TD at the head of this ring's
* TD list.
*/
if (list_empty(&ep_ring->td_list)) {
xhci_warn(xhci, "WARN Event TRB for slot %d ep %d "
"with no TDs queued?\n",
TRB_TO_SLOT_ID(le32_to_cpu(event->flags)),
ep_index);
xhci_dbg(xhci, "Event TRB with TRB type ID %u\n",
(unsigned int) (le32_to_cpu(event->flags)
& TRB_TYPE_BITMASK)>>10);
xhci_print_trb_offsets(xhci, (union xhci_trb *) event);
if (ep->skip) {
ep->skip = false;
xhci_dbg(xhci, "td_list is empty while skip "
"flag set. Clear skip flag.\n");
}
ret = 0;
goto cleanup;
}
td = list_entry(ep_ring->td_list.next, struct xhci_td, td_list);
/* Is this a TRB in the currently executing TD? */
event_seg = trb_in_td(ep_ring->deq_seg, ep_ring->dequeue,
td->last_trb, event_dma);
if (!event_seg) {
if (!ep->skip ||
!usb_endpoint_xfer_isoc(&td->urb->ep->desc)) {
/* HC is busted, give up! */
xhci_err(xhci,
"ERROR Transfer event TRB DMA ptr not "
"part of current TD\n");
return -ESHUTDOWN;
}
ret = skip_isoc_td(xhci, td, event, ep, &status);
goto cleanup;
}
if (ep->skip) {
xhci_dbg(xhci, "Found td. Clear skip flag.\n");
ep->skip = false;
}
USB: xhci: Handle URB cancel, complete and resubmit race. In the old code, there was a race condition between the stop endpoint command and the URB submission process. When the stop endpoint command is handled by the event handler, the endpoint ring is assumed to be stopped. When a stop endpoint command is queued, URB submissions are to not ring the doorbell. The old code would check the number of pending URBs to be canceled, and would not ring the doorbell if it was non-zero. However, the following race condition could occur with the old code: 1. Cancel an URB, add it to the list of URBs to be canceled, queue the stop endpoint command, and increment ep->cancels_pending to 1. 2. The URB finishes on the HW, and an event is enqueued to the event ring (at the same time as 1). 3. The stop endpoint command finishes, and the endpoint is halted. An event is queued to the event ring. 4. The event handler sees the finished URB, notices it was to be canceled, decrements ep->cancels_pending to 0, and removes it from the to be canceled list. 5. The event handler drops the lock and gives back the URB. The completion handler requeues the URB (or a different driver enqueues a new URB). This causes the endpoint's doorbell to be rung, since ep->cancels_pending == 0. The endpoint is now running. 6. A second URB is canceled, and it's added to the canceled list. Since ep->cancels_pending == 0, a new stop endpoint command is queued, and ep->cancels_pending is incremented to 1. 7. The event handler then sees the completed stop endpoint command. The handler assumes the endpoint is stopped, but it isn't. It attempts to move the dequeue pointer or change TDs to cancel the second URB, while the hardware is actively accessing the endpoint ring. To eliminate this race condition, a new endpoint state bit is introduced, EP_HALT_PENDING. When this bit is set, a stop endpoint command has been queued, and the command handler has not begun to process the URB cancellation list yet. The endpoint doorbell should not be rung when this is set. Set this when a stop endpoint command is queued, clear it when the handler for that command runs, and check if it's set before ringing a doorbell. ep->cancels_pending is eliminated, because it is no longer used. Make sure to ring the doorbell for an endpoint when the stop endpoint command handler runs, even if the canceled URB list is empty. All canceled URBs could have completed and new URBs could have been enqueued without the doorbell being rung before the command was handled. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:55:52 +00:00
event_trb = &event_seg->trbs[(event_dma - event_seg->dma) /
sizeof(*event_trb)];
/*
* No-op TRB should not trigger interrupts.
* If event_trb is a no-op TRB, it means the
* corresponding TD has been cancelled. Just ignore
* the TD.
*/
if ((le32_to_cpu(event_trb->generic.field[3])
& TRB_TYPE_BITMASK)
== TRB_TYPE(TRB_TR_NOOP)) {
xhci_dbg(xhci,
"event_trb is a no-op TRB. Skip it\n");
goto cleanup;
}
/* Now update the urb's actual_length and give back to
* the core
*/
if (usb_endpoint_xfer_control(&td->urb->ep->desc))
ret = process_ctrl_td(xhci, td, event_trb, event, ep,
&status);
else if (usb_endpoint_xfer_isoc(&td->urb->ep->desc))
ret = process_isoc_td(xhci, td, event_trb, event, ep,
&status);
else
ret = process_bulk_intr_td(xhci, td, event_trb, event,
ep, &status);
cleanup:
/*
* Do not update event ring dequeue pointer if ep->skip is set.
* Will roll back to continue process missed tds.
*/
if (trb_comp_code == COMP_MISSED_INT || !ep->skip) {
inc_deq(xhci, xhci->event_ring, true);
}
if (ret) {
urb = td->urb;
urb_priv = urb->hcpriv;
/* Leave the TD around for the reset endpoint function
* to use(but only if it's not a control endpoint,
* since we already queued the Set TR dequeue pointer
* command for stalled control endpoints).
*/
if (usb_endpoint_xfer_control(&urb->ep->desc) ||
(trb_comp_code != COMP_STALL &&
trb_comp_code != COMP_BABBLE))
xhci_urb_free_priv(xhci, urb_priv);
usb_hcd_unlink_urb_from_ep(bus_to_hcd(urb->dev->bus), urb);
xhci_dbg(xhci, "Giveback URB %p, len = %d, "
"status = %d\n",
urb, urb->actual_length, status);
spin_unlock(&xhci->lock);
usb_hcd_giveback_urb(bus_to_hcd(urb->dev->bus), urb, status);
spin_lock(&xhci->lock);
}
/*
* If ep->skip is set, it means there are missed tds on the
* endpoint ring need to take care of.
* Process them as short transfer until reach the td pointed by
* the event.
*/
} while (ep->skip && trb_comp_code != COMP_MISSED_INT);
return 0;
}
/*
* This function handles all OS-owned events on the event ring. It may drop
* xhci->lock between event processing (e.g. to pass up port status changes).
* Returns >0 for "possibly more events to process" (caller should call again),
* otherwise 0 if done. In future, <0 returns should indicate error code.
*/
static int xhci_handle_event(struct xhci_hcd *xhci)
{
union xhci_trb *event;
int update_ptrs = 1;
int ret;
xhci_dbg(xhci, "In %s\n", __func__);
if (!xhci->event_ring || !xhci->event_ring->dequeue) {
xhci->error_bitmask |= 1 << 1;
return 0;
}
event = xhci->event_ring->dequeue;
/* Does the HC or OS own the TRB? */
if ((le32_to_cpu(event->event_cmd.flags) & TRB_CYCLE) !=
xhci->event_ring->cycle_state) {
xhci->error_bitmask |= 1 << 2;
return 0;
}
xhci_dbg(xhci, "%s - OS owns TRB\n", __func__);
/*
* Barrier between reading the TRB_CYCLE (valid) flag above and any
* speculative reads of the event's flags/data below.
*/
rmb();
/* FIXME: Handle more event types. */
switch ((le32_to_cpu(event->event_cmd.flags) & TRB_TYPE_BITMASK)) {
case TRB_TYPE(TRB_COMPLETION):
xhci_dbg(xhci, "%s - calling handle_cmd_completion\n", __func__);
handle_cmd_completion(xhci, &event->event_cmd);
xhci_dbg(xhci, "%s - returned from handle_cmd_completion\n", __func__);
break;
case TRB_TYPE(TRB_PORT_STATUS):
xhci_dbg(xhci, "%s - calling handle_port_status\n", __func__);
handle_port_status(xhci, event);
xhci_dbg(xhci, "%s - returned from handle_port_status\n", __func__);
update_ptrs = 0;
break;
case TRB_TYPE(TRB_TRANSFER):
xhci_dbg(xhci, "%s - calling handle_tx_event\n", __func__);
ret = handle_tx_event(xhci, &event->trans_event);
xhci_dbg(xhci, "%s - returned from handle_tx_event\n", __func__);
if (ret < 0)
xhci->error_bitmask |= 1 << 9;
else
update_ptrs = 0;
break;
default:
if ((le32_to_cpu(event->event_cmd.flags) & TRB_TYPE_BITMASK) >=
TRB_TYPE(48))
handle_vendor_event(xhci, event);
else
xhci->error_bitmask |= 1 << 3;
}
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
/* Any of the above functions may drop and re-acquire the lock, so check
* to make sure a watchdog timer didn't mark the host as non-responsive.
*/
if (xhci->xhc_state & XHCI_STATE_DYING) {
xhci_dbg(xhci, "xHCI host dying, returning from "
"event handler.\n");
return 0;
USB: xhci: Add watchdog timer for URB cancellation. In order to giveback a canceled URB, we must ensure that the xHCI hardware will not access the buffer in an URB. We can't modify the buffer pointers on endpoint rings without issuing and waiting for a stop endpoint command. Since URBs can be canceled in interrupt context, we can't wait on that command. The old code trusted that the host controller would respond to the command, and would giveback the URBs in the event handler. If the hardware never responds to the stop endpoint command, the URBs will never be completed, and we might hang the USB subsystem. Implement a watchdog timer that is spawned whenever a stop endpoint command is queued. If a stop endpoint command event is found on the event ring during an interrupt, we need to stop the watchdog timer with del_timer(). Since del_timer() can fail if the timer is running and waiting on the xHCI lock, we need a way to signal to the timer that everything is fine and it should exit. If we simply clear EP_HALT_PENDING, a new stop endpoint command could sneak in and set it before the watchdog timer can grab the lock. Instead we use a combination of the EP_HALT_PENDING flag and a counter for the number of pending stop endpoint commands (xhci_virt_ep->stop_cmds_pending). If we need to cancel the watchdog timer and del_timer() succeeds, we decrement the number of pending stop endpoint commands. If del_timer() fails, we leave the number of pending stop endpoint commands alone. In either case, we clear the EP_HALT_PENDING flag. The timer will decrement the number of pending stop endpoint commands once it obtains the lock. If the timer is the tail end of the last stop endpoint command (xhci_virt_ep->stop_cmds_pending == 0), and the endpoint's command is still pending (EP_HALT_PENDING is set), we assume the host is dying. The watchdog timer will set XHCI_STATE_DYING, try to halt the xHCI host, and give back all pending URBs. Various other places in the driver need to check whether the xHCI host is dying. If the interrupt handler ever notices, it should immediately stop processing events. The URB enqueue function should also return -ESHUTDOWN. The URB dequeue function should simply return the value of usb_hcd_check_unlink_urb() and the watchdog timer will take care of giving the URB back. When a device is disconnected, the xHCI hardware structures should be freed without issuing a disable slot command (since the hardware probably won't respond to it anyway). The debugging polling loop should stop polling if the host is dying. When a device is disconnected, any pending watchdog timers are killed with del_timer_sync(). It must be synchronous so that the watchdog timer doesn't attempt to access the freed endpoint structures. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-10-27 17:57:01 +00:00
}
if (update_ptrs)
/* Update SW event ring dequeue pointer */
inc_deq(xhci, xhci->event_ring, true);
/* Are there more items on the event ring? Caller will call us again to
* check.
*/
return 1;
}
/*
* xHCI spec says we can get an interrupt, and if the HC has an error condition,
* we might get bad data out of the event ring. Section 4.10.2.7 has a list of
* indicators of an event TRB error, but we check the status *first* to be safe.
*/
irqreturn_t xhci_irq(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci = hcd_to_xhci(hcd);
u32 status;
union xhci_trb *trb;
u64 temp_64;
union xhci_trb *event_ring_deq;
dma_addr_t deq;
spin_lock(&xhci->lock);
trb = xhci->event_ring->dequeue;
/* Check if the xHC generated the interrupt, or the irq is shared */
status = xhci_readl(xhci, &xhci->op_regs->status);
if (status == 0xffffffff)
goto hw_died;
if (!(status & STS_EINT)) {
spin_unlock(&xhci->lock);
return IRQ_NONE;
}
xhci_dbg(xhci, "op reg status = %08x\n", status);
xhci_dbg(xhci, "Event ring dequeue ptr:\n");
xhci_dbg(xhci, "@%llx %08x %08x %08x %08x\n",
(unsigned long long)
xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, trb),
lower_32_bits(le64_to_cpu(trb->link.segment_ptr)),
upper_32_bits(le64_to_cpu(trb->link.segment_ptr)),
(unsigned int) le32_to_cpu(trb->link.intr_target),
(unsigned int) le32_to_cpu(trb->link.control));
if (status & STS_FATAL) {
xhci_warn(xhci, "WARNING: Host System Error\n");
xhci_halt(xhci);
hw_died:
spin_unlock(&xhci->lock);
return -ESHUTDOWN;
}
/*
* Clear the op reg interrupt status first,
* so we can receive interrupts from other MSI-X interrupters.
* Write 1 to clear the interrupt status.
*/
status |= STS_EINT;
xhci_writel(xhci, status, &xhci->op_regs->status);
/* FIXME when MSI-X is supported and there are multiple vectors */
/* Clear the MSI-X event interrupt status */
if (hcd->irq != -1) {
u32 irq_pending;
/* Acknowledge the PCI interrupt */
irq_pending = xhci_readl(xhci, &xhci->ir_set->irq_pending);
irq_pending |= 0x3;
xhci_writel(xhci, irq_pending, &xhci->ir_set->irq_pending);
}
if (xhci->xhc_state & XHCI_STATE_DYING) {
xhci_dbg(xhci, "xHCI dying, ignoring interrupt. "
"Shouldn't IRQs be disabled?\n");
/* Clear the event handler busy flag (RW1C);
* the event ring should be empty.
*/
temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
xhci_write_64(xhci, temp_64 | ERST_EHB,
&xhci->ir_set->erst_dequeue);
spin_unlock(&xhci->lock);
return IRQ_HANDLED;
}
event_ring_deq = xhci->event_ring->dequeue;
/* FIXME this should be a delayed service routine
* that clears the EHB.
*/
while (xhci_handle_event(xhci) > 0) {}
temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue);
/* If necessary, update the HW's version of the event ring deq ptr. */
if (event_ring_deq != xhci->event_ring->dequeue) {
deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg,
xhci->event_ring->dequeue);
if (deq == 0)
xhci_warn(xhci, "WARN something wrong with SW event "
"ring dequeue ptr.\n");
/* Update HC event ring dequeue pointer */
temp_64 &= ERST_PTR_MASK;
temp_64 |= ((u64) deq & (u64) ~ERST_PTR_MASK);
}
/* Clear the event handler busy flag (RW1C); event ring is empty. */
temp_64 |= ERST_EHB;
xhci_write_64(xhci, temp_64, &xhci->ir_set->erst_dequeue);
spin_unlock(&xhci->lock);
return IRQ_HANDLED;
}
irqreturn_t xhci_msi_irq(int irq, struct usb_hcd *hcd)
{
irqreturn_t ret;
struct xhci_hcd *xhci;
xhci = hcd_to_xhci(hcd);
set_bit(HCD_FLAG_SAW_IRQ, &hcd->flags);
if (xhci->shared_hcd)
set_bit(HCD_FLAG_SAW_IRQ, &xhci->shared_hcd->flags);
ret = xhci_irq(hcd);
return ret;
}
/**** Endpoint Ring Operations ****/
/*
* Generic function for queueing a TRB on a ring.
* The caller must have checked to make sure there's room on the ring.
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
*
* @more_trbs_coming: Will you enqueue more TRBs before calling
* prepare_transfer()?
*/
static void queue_trb(struct xhci_hcd *xhci, struct xhci_ring *ring,
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
bool consumer, bool more_trbs_coming,
u32 field1, u32 field2, u32 field3, u32 field4)
{
struct xhci_generic_trb *trb;
trb = &ring->enqueue->generic;
trb->field[0] = cpu_to_le32(field1);
trb->field[1] = cpu_to_le32(field2);
trb->field[2] = cpu_to_le32(field3);
trb->field[3] = cpu_to_le32(field4);
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
inc_enq(xhci, ring, consumer, more_trbs_coming);
}
/*
* Does various checks on the endpoint ring, and makes it ready to queue num_trbs.
* FIXME allocate segments if the ring is full.
*/
static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring,
u32 ep_state, unsigned int num_trbs, gfp_t mem_flags)
{
/* Make sure the endpoint has been added to xHC schedule */
xhci_dbg(xhci, "Endpoint state = 0x%x\n", ep_state);
switch (ep_state) {
case EP_STATE_DISABLED:
/*
* USB core changed config/interfaces without notifying us,
* or hardware is reporting the wrong state.
*/
xhci_warn(xhci, "WARN urb submitted to disabled ep\n");
return -ENOENT;
case EP_STATE_ERROR:
xhci_warn(xhci, "WARN waiting for error on ep to be cleared\n");
/* FIXME event handling code for error needs to clear it */
/* XXX not sure if this should be -ENOENT or not */
return -EINVAL;
case EP_STATE_HALTED:
xhci_dbg(xhci, "WARN halted endpoint, queueing URB anyway.\n");
case EP_STATE_STOPPED:
case EP_STATE_RUNNING:
break;
default:
xhci_err(xhci, "ERROR unknown endpoint state for ep\n");
/*
* FIXME issue Configure Endpoint command to try to get the HC
* back into a known state.
*/
return -EINVAL;
}
if (!room_on_ring(xhci, ep_ring, num_trbs)) {
/* FIXME allocate more room */
xhci_err(xhci, "ERROR no room on ep ring\n");
return -ENOMEM;
}
if (enqueue_is_link_trb(ep_ring)) {
struct xhci_ring *ring = ep_ring;
union xhci_trb *next;
xhci_dbg(xhci, "prepare_ring: pointing to link trb\n");
next = ring->enqueue;
while (last_trb(xhci, ring, ring->enq_seg, next)) {
/* If we're not dealing with 0.95 hardware,
* clear the chain bit.
*/
if (!xhci_link_trb_quirk(xhci))
next->link.control &= cpu_to_le32(~TRB_CHAIN);
else
next->link.control |= cpu_to_le32(TRB_CHAIN);
wmb();
next->link.control ^= cpu_to_le32((u32) TRB_CYCLE);
/* Toggle the cycle bit after the last ring segment. */
if (last_trb_on_last_seg(xhci, ring, ring->enq_seg, next)) {
ring->cycle_state = (ring->cycle_state ? 0 : 1);
if (!in_interrupt()) {
xhci_dbg(xhci, "queue_trb: Toggle cycle "
"state for ring %p = %i\n",
ring, (unsigned int)ring->cycle_state);
}
}
ring->enq_seg = ring->enq_seg->next;
ring->enqueue = ring->enq_seg->trbs;
next = ring->enqueue;
}
}
return 0;
}
static int prepare_transfer(struct xhci_hcd *xhci,
struct xhci_virt_device *xdev,
unsigned int ep_index,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int stream_id,
unsigned int num_trbs,
struct urb *urb,
unsigned int td_index,
gfp_t mem_flags)
{
int ret;
struct urb_priv *urb_priv;
struct xhci_td *td;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
struct xhci_ring *ep_ring;
struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep_ring = xhci_stream_id_to_ring(xdev, ep_index, stream_id);
if (!ep_ring) {
xhci_dbg(xhci, "Can't prepare ring for bad stream ID %u\n",
stream_id);
return -EINVAL;
}
ret = prepare_ring(xhci, ep_ring,
le32_to_cpu(ep_ctx->ep_info) & EP_STATE_MASK,
num_trbs, mem_flags);
if (ret)
return ret;
urb_priv = urb->hcpriv;
td = urb_priv->td[td_index];
INIT_LIST_HEAD(&td->td_list);
INIT_LIST_HEAD(&td->cancelled_td_list);
if (td_index == 0) {
ret = usb_hcd_link_urb_to_ep(bus_to_hcd(urb->dev->bus), urb);
if (unlikely(ret)) {
xhci_urb_free_priv(xhci, urb_priv);
urb->hcpriv = NULL;
return ret;
}
}
td->urb = urb;
/* Add this TD to the tail of the endpoint ring's TD list */
list_add_tail(&td->td_list, &ep_ring->td_list);
td->start_seg = ep_ring->enq_seg;
td->first_trb = ep_ring->enqueue;
urb_priv->td[td_index] = td;
return 0;
}
static unsigned int count_sg_trbs_needed(struct xhci_hcd *xhci, struct urb *urb)
{
int num_sgs, num_trbs, running_total, temp, i;
struct scatterlist *sg;
sg = NULL;
num_sgs = urb->num_sgs;
temp = urb->transfer_buffer_length;
xhci_dbg(xhci, "count sg list trbs: \n");
num_trbs = 0;
for_each_sg(urb->sg, sg, num_sgs, i) {
unsigned int previous_total_trbs = num_trbs;
unsigned int len = sg_dma_len(sg);
/* Scatter gather list entries may cross 64KB boundaries */
running_total = TRB_MAX_BUFF_SIZE -
(sg_dma_address(sg) & (TRB_MAX_BUFF_SIZE - 1));
running_total &= TRB_MAX_BUFF_SIZE - 1;
if (running_total != 0)
num_trbs++;
/* How many more 64KB chunks to transfer, how many more TRBs? */
while (running_total < sg_dma_len(sg) && running_total < temp) {
num_trbs++;
running_total += TRB_MAX_BUFF_SIZE;
}
xhci_dbg(xhci, " sg #%d: dma = %#llx, len = %#x (%d), num_trbs = %d\n",
i, (unsigned long long)sg_dma_address(sg),
len, len, num_trbs - previous_total_trbs);
len = min_t(int, len, temp);
temp -= len;
if (temp == 0)
break;
}
xhci_dbg(xhci, "\n");
if (!in_interrupt())
xhci_dbg(xhci, "ep %#x - urb len = %d, sglist used, "
"num_trbs = %d\n",
urb->ep->desc.bEndpointAddress,
urb->transfer_buffer_length,
num_trbs);
return num_trbs;
}
static void check_trb_math(struct urb *urb, int num_trbs, int running_total)
{
if (num_trbs != 0)
dev_err(&urb->dev->dev, "%s - ep %#x - Miscalculated number of "
"TRBs, %d left\n", __func__,
urb->ep->desc.bEndpointAddress, num_trbs);
if (running_total != urb->transfer_buffer_length)
dev_err(&urb->dev->dev, "%s - ep %#x - Miscalculated tx length, "
"queued %#x (%d), asked for %#x (%d)\n",
__func__,
urb->ep->desc.bEndpointAddress,
running_total, running_total,
urb->transfer_buffer_length,
urb->transfer_buffer_length);
}
static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int ep_index, unsigned int stream_id, int start_cycle,
struct xhci_generic_trb *start_trb)
{
/*
* Pass all the TRBs to the hardware at once and make sure this write
* isn't reordered.
*/
wmb();
if (start_cycle)
start_trb->field[3] |= cpu_to_le32(start_cycle);
else
start_trb->field[3] &= cpu_to_le32(~TRB_CYCLE);
xhci_ring_ep_doorbell(xhci, slot_id, ep_index, stream_id);
}
/*
* xHCI uses normal TRBs for both bulk and interrupt. When the interrupt
* endpoint is to be serviced, the xHC will consume (at most) one TD. A TD
* (comprised of sg list entries) can take several service intervals to
* transmit.
*/
int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
struct urb *urb, int slot_id, unsigned int ep_index)
{
struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci,
xhci->devs[slot_id]->out_ctx, ep_index);
int xhci_interval;
int ep_interval;
xhci_interval = EP_INTERVAL_TO_UFRAMES(le32_to_cpu(ep_ctx->ep_info));
ep_interval = urb->interval;
/* Convert to microframes */
if (urb->dev->speed == USB_SPEED_LOW ||
urb->dev->speed == USB_SPEED_FULL)
ep_interval *= 8;
/* FIXME change this to a warning and a suggestion to use the new API
* to set the polling interval (once the API is added).
*/
if (xhci_interval != ep_interval) {
if (printk_ratelimit())
dev_dbg(&urb->dev->dev, "Driver uses different interval"
" (%d microframe%s) than xHCI "
"(%d microframe%s)\n",
ep_interval,
ep_interval == 1 ? "" : "s",
xhci_interval,
xhci_interval == 1 ? "" : "s");
urb->interval = xhci_interval;
/* Convert back to frames for LS/FS devices */
if (urb->dev->speed == USB_SPEED_LOW ||
urb->dev->speed == USB_SPEED_FULL)
urb->interval /= 8;
}
return xhci_queue_bulk_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index);
}
/*
* The TD size is the number of bytes remaining in the TD (including this TRB),
* right shifted by 10.
* It must fit in bits 21:17, so it can't be bigger than 31.
*/
static u32 xhci_td_remainder(unsigned int remainder)
{
u32 max = (1 << (21 - 17 + 1)) - 1;
if ((remainder >> 10) >= max)
return max << 17;
else
return (remainder >> 10) << 17;
}
/*
* For xHCI 1.0 host controllers, TD size is the number of packets remaining in
* the TD (*not* including this TRB).
*
* Total TD packet count = total_packet_count =
* roundup(TD size in bytes / wMaxPacketSize)
*
* Packets transferred up to and including this TRB = packets_transferred =
* rounddown(total bytes transferred including this TRB / wMaxPacketSize)
*
* TD size = total_packet_count - packets_transferred
*
* It must fit in bits 21:17, so it can't be bigger than 31.
*/
static u32 xhci_v1_0_td_remainder(int running_total, int trb_buff_len,
unsigned int total_packet_count, struct urb *urb)
{
int packets_transferred;
/* All the TRB queueing functions don't count the current TRB in
* running_total.
*/
packets_transferred = (running_total + trb_buff_len) /
le16_to_cpu(urb->ep->desc.wMaxPacketSize);
return xhci_td_remainder(total_packet_count - packets_transferred);
}
static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
struct urb *urb, int slot_id, unsigned int ep_index)
{
struct xhci_ring *ep_ring;
unsigned int num_trbs;
struct urb_priv *urb_priv;
struct xhci_td *td;
struct scatterlist *sg;
int num_sgs;
int trb_buff_len, this_sg_len, running_total;
unsigned int total_packet_count;
bool first_trb;
u64 addr;
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
bool more_trbs_coming;
struct xhci_generic_trb *start_trb;
int start_cycle;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
if (!ep_ring)
return -EINVAL;
num_trbs = count_sg_trbs_needed(xhci, urb);
num_sgs = urb->num_sgs;
total_packet_count = roundup(urb->transfer_buffer_length,
le16_to_cpu(urb->ep->desc.wMaxPacketSize));
trb_buff_len = prepare_transfer(xhci, xhci->devs[slot_id],
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep_index, urb->stream_id,
num_trbs, urb, 0, mem_flags);
if (trb_buff_len < 0)
return trb_buff_len;
urb_priv = urb->hcpriv;
td = urb_priv->td[0];
/*
* Don't give the first TRB to the hardware (by toggling the cycle bit)
* until we've finished creating all the other TRBs. The ring's cycle
* state may change as we enqueue the other TRBs, so save it too.
*/
start_trb = &ep_ring->enqueue->generic;
start_cycle = ep_ring->cycle_state;
running_total = 0;
/*
* How much data is in the first TRB?
*
* There are three forces at work for TRB buffer pointers and lengths:
* 1. We don't want to walk off the end of this sg-list entry buffer.
* 2. The transfer length that the driver requested may be smaller than
* the amount of memory allocated for this scatter-gather list.
* 3. TRBs buffers can't cross 64KB boundaries.
*/
sg = urb->sg;
addr = (u64) sg_dma_address(sg);
this_sg_len = sg_dma_len(sg);
trb_buff_len = TRB_MAX_BUFF_SIZE - (addr & (TRB_MAX_BUFF_SIZE - 1));
trb_buff_len = min_t(int, trb_buff_len, this_sg_len);
if (trb_buff_len > urb->transfer_buffer_length)
trb_buff_len = urb->transfer_buffer_length;
xhci_dbg(xhci, "First length to xfer from 1st sglist entry = %u\n",
trb_buff_len);
first_trb = true;
/* Queue the first TRB, even if it's zero-length */
do {
u32 field = 0;
u32 length_field = 0;
u32 remainder = 0;
/* Don't change the cycle bit of the first TRB until later */
if (first_trb) {
first_trb = false;
if (start_cycle == 0)
field |= 0x1;
} else
field |= ep_ring->cycle_state;
/* Chain all the TRBs together; clear the chain bit in the last
* TRB to indicate it's the last TRB in the chain.
*/
if (num_trbs > 1) {
field |= TRB_CHAIN;
} else {
/* FIXME - add check for ZERO_PACKET flag before this */
td->last_trb = ep_ring->enqueue;
field |= TRB_IOC;
}
/* Only set interrupt on short packet for IN endpoints */
if (usb_urb_dir_in(urb))
field |= TRB_ISP;
xhci_dbg(xhci, " sg entry: dma = %#x, len = %#x (%d), "
"64KB boundary at %#x, end dma = %#x\n",
(unsigned int) addr, trb_buff_len, trb_buff_len,
(unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1),
(unsigned int) addr + trb_buff_len);
if (TRB_MAX_BUFF_SIZE -
(addr & (TRB_MAX_BUFF_SIZE - 1)) < trb_buff_len) {
xhci_warn(xhci, "WARN: sg dma xfer crosses 64KB boundaries!\n");
xhci_dbg(xhci, "Next boundary at %#x, end dma = %#x\n",
(unsigned int) (addr + TRB_MAX_BUFF_SIZE) & ~(TRB_MAX_BUFF_SIZE - 1),
(unsigned int) addr + trb_buff_len);
}
/* Set the TRB length, TD size, and interrupter fields. */
if (xhci->hci_version < 0x100) {
remainder = xhci_td_remainder(
urb->transfer_buffer_length -
running_total);
} else {
remainder = xhci_v1_0_td_remainder(running_total,
trb_buff_len, total_packet_count, urb);
}
length_field = TRB_LEN(trb_buff_len) |
remainder |
TRB_INTR_TARGET(0);
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
if (num_trbs > 1)
more_trbs_coming = true;
else
more_trbs_coming = false;
queue_trb(xhci, ep_ring, false, more_trbs_coming,
lower_32_bits(addr),
upper_32_bits(addr),
length_field,
field | TRB_TYPE(TRB_NORMAL));
--num_trbs;
running_total += trb_buff_len;
/* Calculate length for next transfer --
* Are we done queueing all the TRBs for this sg entry?
*/
this_sg_len -= trb_buff_len;
if (this_sg_len == 0) {
--num_sgs;
if (num_sgs == 0)
break;
sg = sg_next(sg);
addr = (u64) sg_dma_address(sg);
this_sg_len = sg_dma_len(sg);
} else {
addr += trb_buff_len;
}
trb_buff_len = TRB_MAX_BUFF_SIZE -
(addr & (TRB_MAX_BUFF_SIZE - 1));
trb_buff_len = min_t(int, trb_buff_len, this_sg_len);
if (running_total + trb_buff_len > urb->transfer_buffer_length)
trb_buff_len =
urb->transfer_buffer_length - running_total;
} while (running_total < urb->transfer_buffer_length);
check_trb_math(urb, num_trbs, running_total);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id,
start_cycle, start_trb);
return 0;
}
/* This is very similar to what ehci-q.c qtd_fill() does */
int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
struct urb *urb, int slot_id, unsigned int ep_index)
{
struct xhci_ring *ep_ring;
struct urb_priv *urb_priv;
struct xhci_td *td;
int num_trbs;
struct xhci_generic_trb *start_trb;
bool first_trb;
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
bool more_trbs_coming;
int start_cycle;
u32 field, length_field;
int running_total, trb_buff_len, ret;
unsigned int total_packet_count;
u64 addr;
2010-04-02 17:27:28 +00:00
if (urb->num_sgs)
return queue_bulk_sg_tx(xhci, mem_flags, urb, slot_id, ep_index);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
if (!ep_ring)
return -EINVAL;
num_trbs = 0;
/* How much data is (potentially) left before the 64KB boundary? */
running_total = TRB_MAX_BUFF_SIZE -
(urb->transfer_dma & (TRB_MAX_BUFF_SIZE - 1));
running_total &= TRB_MAX_BUFF_SIZE - 1;
/* If there's some data on this 64KB chunk, or we have to send a
* zero-length transfer, we need at least one TRB
*/
if (running_total != 0 || urb->transfer_buffer_length == 0)
num_trbs++;
/* How many more 64KB chunks to transfer, how many more TRBs? */
while (running_total < urb->transfer_buffer_length) {
num_trbs++;
running_total += TRB_MAX_BUFF_SIZE;
}
/* FIXME: this doesn't deal with URB_ZERO_PACKET - need one more */
if (!in_interrupt())
xhci_dbg(xhci, "ep %#x - urb len = %#x (%d), "
"addr = %#llx, num_trbs = %d\n",
urb->ep->desc.bEndpointAddress,
urb->transfer_buffer_length,
urb->transfer_buffer_length,
(unsigned long long)urb->transfer_dma,
num_trbs);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ret = prepare_transfer(xhci, xhci->devs[slot_id],
ep_index, urb->stream_id,
num_trbs, urb, 0, mem_flags);
if (ret < 0)
return ret;
urb_priv = urb->hcpriv;
td = urb_priv->td[0];
/*
* Don't give the first TRB to the hardware (by toggling the cycle bit)
* until we've finished creating all the other TRBs. The ring's cycle
* state may change as we enqueue the other TRBs, so save it too.
*/
start_trb = &ep_ring->enqueue->generic;
start_cycle = ep_ring->cycle_state;
running_total = 0;
total_packet_count = roundup(urb->transfer_buffer_length,
le16_to_cpu(urb->ep->desc.wMaxPacketSize));
/* How much data is in the first TRB? */
addr = (u64) urb->transfer_dma;
trb_buff_len = TRB_MAX_BUFF_SIZE -
(urb->transfer_dma & (TRB_MAX_BUFF_SIZE - 1));
if (trb_buff_len > urb->transfer_buffer_length)
trb_buff_len = urb->transfer_buffer_length;
first_trb = true;
/* Queue the first TRB, even if it's zero-length */
do {
u32 remainder = 0;
field = 0;
/* Don't change the cycle bit of the first TRB until later */
if (first_trb) {
first_trb = false;
if (start_cycle == 0)
field |= 0x1;
} else
field |= ep_ring->cycle_state;
/* Chain all the TRBs together; clear the chain bit in the last
* TRB to indicate it's the last TRB in the chain.
*/
if (num_trbs > 1) {
field |= TRB_CHAIN;
} else {
/* FIXME - add check for ZERO_PACKET flag before this */
td->last_trb = ep_ring->enqueue;
field |= TRB_IOC;
}
/* Only set interrupt on short packet for IN endpoints */
if (usb_urb_dir_in(urb))
field |= TRB_ISP;
/* Set the TRB length, TD size, and interrupter fields. */
if (xhci->hci_version < 0x100) {
remainder = xhci_td_remainder(
urb->transfer_buffer_length -
running_total);
} else {
remainder = xhci_v1_0_td_remainder(running_total,
trb_buff_len, total_packet_count, urb);
}
length_field = TRB_LEN(trb_buff_len) |
remainder |
TRB_INTR_TARGET(0);
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
if (num_trbs > 1)
more_trbs_coming = true;
else
more_trbs_coming = false;
queue_trb(xhci, ep_ring, false, more_trbs_coming,
lower_32_bits(addr),
upper_32_bits(addr),
length_field,
field | TRB_TYPE(TRB_NORMAL));
--num_trbs;
running_total += trb_buff_len;
/* Calculate length for next transfer */
addr += trb_buff_len;
trb_buff_len = urb->transfer_buffer_length - running_total;
if (trb_buff_len > TRB_MAX_BUFF_SIZE)
trb_buff_len = TRB_MAX_BUFF_SIZE;
} while (running_total < urb->transfer_buffer_length);
check_trb_math(urb, num_trbs, running_total);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id,
start_cycle, start_trb);
return 0;
}
/* Caller must have locked xhci->lock */
int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
struct urb *urb, int slot_id, unsigned int ep_index)
{
struct xhci_ring *ep_ring;
int num_trbs;
int ret;
struct usb_ctrlrequest *setup;
struct xhci_generic_trb *start_trb;
int start_cycle;
u32 field, length_field;
struct urb_priv *urb_priv;
struct xhci_td *td;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ep_ring = xhci_urb_to_transfer_ring(xhci, urb);
if (!ep_ring)
return -EINVAL;
/*
* Need to copy setup packet into setup TRB, so we can't use the setup
* DMA address.
*/
if (!urb->setup_packet)
return -EINVAL;
if (!in_interrupt())
xhci_dbg(xhci, "Queueing ctrl tx for slot id %d, ep %d\n",
slot_id, ep_index);
/* 1 TRB for setup, 1 for status */
num_trbs = 2;
/*
* Don't need to check if we need additional event data and normal TRBs,
* since data in control transfers will never get bigger than 16MB
* XXX: can we get a buffer that crosses 64KB boundaries?
*/
if (urb->transfer_buffer_length > 0)
num_trbs++;
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
ret = prepare_transfer(xhci, xhci->devs[slot_id],
ep_index, urb->stream_id,
num_trbs, urb, 0, mem_flags);
if (ret < 0)
return ret;
urb_priv = urb->hcpriv;
td = urb_priv->td[0];
/*
* Don't give the first TRB to the hardware (by toggling the cycle bit)
* until we've finished creating all the other TRBs. The ring's cycle
* state may change as we enqueue the other TRBs, so save it too.
*/
start_trb = &ep_ring->enqueue->generic;
start_cycle = ep_ring->cycle_state;
/* Queue setup TRB - see section 6.4.1.2.1 */
/* FIXME better way to translate setup_packet into two u32 fields? */
setup = (struct usb_ctrlrequest *) urb->setup_packet;
field = 0;
field |= TRB_IDT | TRB_TYPE(TRB_SETUP);
if (start_cycle == 0)
field |= 0x1;
/* xHCI 1.0 6.4.1.2.1: Transfer Type field */
if (xhci->hci_version == 0x100) {
if (urb->transfer_buffer_length > 0) {
if (setup->bRequestType & USB_DIR_IN)
field |= TRB_TX_TYPE(TRB_DATA_IN);
else
field |= TRB_TX_TYPE(TRB_DATA_OUT);
}
}
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
queue_trb(xhci, ep_ring, false, true,
setup->bRequestType | setup->bRequest << 8 | le16_to_cpu(setup->wValue) << 16,
le16_to_cpu(setup->wIndex) | le16_to_cpu(setup->wLength) << 16,
TRB_LEN(8) | TRB_INTR_TARGET(0),
/* Immediate data in pointer */
field);
/* If there's data, queue data TRBs */
/* Only set interrupt on short packet for IN endpoints */
if (usb_urb_dir_in(urb))
field = TRB_ISP | TRB_TYPE(TRB_DATA);
else
field = TRB_TYPE(TRB_DATA);
length_field = TRB_LEN(urb->transfer_buffer_length) |
xhci_td_remainder(urb->transfer_buffer_length) |
TRB_INTR_TARGET(0);
if (urb->transfer_buffer_length > 0) {
if (setup->bRequestType & USB_DIR_IN)
field |= TRB_DIR_IN;
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
queue_trb(xhci, ep_ring, false, true,
lower_32_bits(urb->transfer_dma),
upper_32_bits(urb->transfer_dma),
length_field,
field | ep_ring->cycle_state);
}
/* Save the DMA address of the last TRB in the TD */
td->last_trb = ep_ring->enqueue;
/* Queue status TRB - see Table 7 and sections 4.11.2.2 and 6.4.1.2.3 */
/* If the device sent data, the status stage is an OUT transfer */
if (urb->transfer_buffer_length > 0 && setup->bRequestType & USB_DIR_IN)
field = 0;
else
field = TRB_DIR_IN;
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
queue_trb(xhci, ep_ring, false, false,
0,
0,
TRB_INTR_TARGET(0),
/* Event on completion */
field | TRB_IOC | TRB_TYPE(TRB_STATUS) | ep_ring->cycle_state);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
giveback_first_trb(xhci, slot_id, ep_index, 0,
start_cycle, start_trb);
return 0;
}
static int count_isoc_trbs_needed(struct xhci_hcd *xhci,
struct urb *urb, int i)
{
int num_trbs = 0;
u64 addr, td_len, running_total;
addr = (u64) (urb->transfer_dma + urb->iso_frame_desc[i].offset);
td_len = urb->iso_frame_desc[i].length;
running_total = TRB_MAX_BUFF_SIZE - (addr & (TRB_MAX_BUFF_SIZE - 1));
running_total &= TRB_MAX_BUFF_SIZE - 1;
if (running_total != 0)
num_trbs++;
while (running_total < td_len) {
num_trbs++;
running_total += TRB_MAX_BUFF_SIZE;
}
return num_trbs;
}
/*
* The transfer burst count field of the isochronous TRB defines the number of
* bursts that are required to move all packets in this TD. Only SuperSpeed
* devices can burst up to bMaxBurst number of packets per service interval.
* This field is zero based, meaning a value of zero in the field means one
* burst. Basically, for everything but SuperSpeed devices, this field will be
* zero. Only xHCI 1.0 host controllers support this field.
*/
static unsigned int xhci_get_burst_count(struct xhci_hcd *xhci,
struct usb_device *udev,
struct urb *urb, unsigned int total_packet_count)
{
unsigned int max_burst;
if (xhci->hci_version < 0x100 || udev->speed != USB_SPEED_SUPER)
return 0;
max_burst = urb->ep->ss_ep_comp.bMaxBurst;
return roundup(total_packet_count, max_burst + 1) - 1;
}
/*
* Returns the number of packets in the last "burst" of packets. This field is
* valid for all speeds of devices. USB 2.0 devices can only do one "burst", so
* the last burst packet count is equal to the total number of packets in the
* TD. SuperSpeed endpoints can have up to 3 bursts. All but the last burst
* must contain (bMaxBurst + 1) number of packets, but the last burst can
* contain 1 to (bMaxBurst + 1) packets.
*/
static unsigned int xhci_get_last_burst_packet_count(struct xhci_hcd *xhci,
struct usb_device *udev,
struct urb *urb, unsigned int total_packet_count)
{
unsigned int max_burst;
unsigned int residue;
if (xhci->hci_version < 0x100)
return 0;
switch (udev->speed) {
case USB_SPEED_SUPER:
/* bMaxBurst is zero based: 0 means 1 packet per burst */
max_burst = urb->ep->ss_ep_comp.bMaxBurst;
residue = total_packet_count % (max_burst + 1);
/* If residue is zero, the last burst contains (max_burst + 1)
* number of packets, but the TLBPC field is zero-based.
*/
if (residue == 0)
return max_burst;
return residue - 1;
default:
if (total_packet_count == 0)
return 0;
return total_packet_count - 1;
}
}
/* This is for isoc transfer */
static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags,
struct urb *urb, int slot_id, unsigned int ep_index)
{
struct xhci_ring *ep_ring;
struct urb_priv *urb_priv;
struct xhci_td *td;
int num_tds, trbs_per_td;
struct xhci_generic_trb *start_trb;
bool first_trb;
int start_cycle;
u32 field, length_field;
int running_total, trb_buff_len, td_len, td_remain_len, ret;
u64 start_addr, addr;
int i, j;
bool more_trbs_coming;
ep_ring = xhci->devs[slot_id]->eps[ep_index].ring;
num_tds = urb->number_of_packets;
if (num_tds < 1) {
xhci_dbg(xhci, "Isoc URB with zero packets?\n");
return -EINVAL;
}
if (!in_interrupt())
xhci_dbg(xhci, "ep %#x - urb len = %#x (%d),"
" addr = %#llx, num_tds = %d\n",
urb->ep->desc.bEndpointAddress,
urb->transfer_buffer_length,
urb->transfer_buffer_length,
(unsigned long long)urb->transfer_dma,
num_tds);
start_addr = (u64) urb->transfer_dma;
start_trb = &ep_ring->enqueue->generic;
start_cycle = ep_ring->cycle_state;
/* Queue the first TRB, even if it's zero-length */
for (i = 0; i < num_tds; i++) {
unsigned int total_packet_count;
unsigned int burst_count;
unsigned int residue;
first_trb = true;
running_total = 0;
addr = start_addr + urb->iso_frame_desc[i].offset;
td_len = urb->iso_frame_desc[i].length;
td_remain_len = td_len;
/* FIXME: Ignoring zero-length packets, can those happen? */
total_packet_count = roundup(td_len,
le16_to_cpu(urb->ep->desc.wMaxPacketSize));
burst_count = xhci_get_burst_count(xhci, urb->dev, urb,
total_packet_count);
residue = xhci_get_last_burst_packet_count(xhci,
urb->dev, urb, total_packet_count);
trbs_per_td = count_isoc_trbs_needed(xhci, urb, i);
ret = prepare_transfer(xhci, xhci->devs[slot_id], ep_index,
urb->stream_id, trbs_per_td, urb, i, mem_flags);
if (ret < 0)
return ret;
urb_priv = urb->hcpriv;
td = urb_priv->td[i];
for (j = 0; j < trbs_per_td; j++) {
u32 remainder = 0;
field = TRB_TBC(burst_count) | TRB_TLBPC(residue);
if (first_trb) {
/* Queue the isoc TRB */
field |= TRB_TYPE(TRB_ISOC);
/* Assume URB_ISO_ASAP is set */
field |= TRB_SIA;
if (i == 0) {
if (start_cycle == 0)
field |= 0x1;
} else
field |= ep_ring->cycle_state;
first_trb = false;
} else {
/* Queue other normal TRBs */
field |= TRB_TYPE(TRB_NORMAL);
field |= ep_ring->cycle_state;
}
/* Only set interrupt on short packet for IN EPs */
if (usb_urb_dir_in(urb))
field |= TRB_ISP;
/* Chain all the TRBs together; clear the chain bit in
* the last TRB to indicate it's the last TRB in the
* chain.
*/
if (j < trbs_per_td - 1) {
field |= TRB_CHAIN;
more_trbs_coming = true;
} else {
td->last_trb = ep_ring->enqueue;
field |= TRB_IOC;
if (xhci->hci_version == 0x100) {
/* Set BEI bit except for the last td */
if (i < num_tds - 1)
field |= TRB_BEI;
}
more_trbs_coming = false;
}
/* Calculate TRB length */
trb_buff_len = TRB_MAX_BUFF_SIZE -
(addr & ((1 << TRB_MAX_BUFF_SHIFT) - 1));
if (trb_buff_len > td_remain_len)
trb_buff_len = td_remain_len;
/* Set the TRB length, TD size, & interrupter fields. */
if (xhci->hci_version < 0x100) {
remainder = xhci_td_remainder(
td_len - running_total);
} else {
remainder = xhci_v1_0_td_remainder(
running_total, trb_buff_len,
total_packet_count, urb);
}
length_field = TRB_LEN(trb_buff_len) |
remainder |
TRB_INTR_TARGET(0);
queue_trb(xhci, ep_ring, false, more_trbs_coming,
lower_32_bits(addr),
upper_32_bits(addr),
length_field,
field);
running_total += trb_buff_len;
addr += trb_buff_len;
td_remain_len -= trb_buff_len;
}
/* Check TD length */
if (running_total != td_len) {
xhci_err(xhci, "ISOC TD length unmatch\n");
return -EINVAL;
}
}
if (xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs == 0) {
if (xhci->quirks & XHCI_AMD_PLL_FIX)
usb_amd_quirk_pll_disable();
}
xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs++;
giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id,
start_cycle, start_trb);
return 0;
}
/*
* Check transfer ring to guarantee there is enough room for the urb.
* Update ISO URB start_frame and interval.
* Update interval as xhci_queue_intr_tx does. Just use xhci frame_index to
* update the urb->start_frame by now.
* Always assume URB_ISO_ASAP set, and NEVER use urb->start_frame as input.
*/
int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags,
struct urb *urb, int slot_id, unsigned int ep_index)
{
struct xhci_virt_device *xdev;
struct xhci_ring *ep_ring;
struct xhci_ep_ctx *ep_ctx;
int start_frame;
int xhci_interval;
int ep_interval;
int num_tds, num_trbs, i;
int ret;
xdev = xhci->devs[slot_id];
ep_ring = xdev->eps[ep_index].ring;
ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index);
num_trbs = 0;
num_tds = urb->number_of_packets;
for (i = 0; i < num_tds; i++)
num_trbs += count_isoc_trbs_needed(xhci, urb, i);
/* Check the ring to guarantee there is enough room for the whole urb.
* Do not insert any td of the urb to the ring if the check failed.
*/
ret = prepare_ring(xhci, ep_ring, le32_to_cpu(ep_ctx->ep_info) & EP_STATE_MASK,
num_trbs, mem_flags);
if (ret)
return ret;
start_frame = xhci_readl(xhci, &xhci->run_regs->microframe_index);
start_frame &= 0x3fff;
urb->start_frame = start_frame;
if (urb->dev->speed == USB_SPEED_LOW ||
urb->dev->speed == USB_SPEED_FULL)
urb->start_frame >>= 3;
xhci_interval = EP_INTERVAL_TO_UFRAMES(le32_to_cpu(ep_ctx->ep_info));
ep_interval = urb->interval;
/* Convert to microframes */
if (urb->dev->speed == USB_SPEED_LOW ||
urb->dev->speed == USB_SPEED_FULL)
ep_interval *= 8;
/* FIXME change this to a warning and a suggestion to use the new API
* to set the polling interval (once the API is added).
*/
if (xhci_interval != ep_interval) {
if (printk_ratelimit())
dev_dbg(&urb->dev->dev, "Driver uses different interval"
" (%d microframe%s) than xHCI "
"(%d microframe%s)\n",
ep_interval,
ep_interval == 1 ? "" : "s",
xhci_interval,
xhci_interval == 1 ? "" : "s");
urb->interval = xhci_interval;
/* Convert back to frames for LS/FS devices */
if (urb->dev->speed == USB_SPEED_LOW ||
urb->dev->speed == USB_SPEED_FULL)
urb->interval /= 8;
}
return xhci_queue_isoc_tx(xhci, GFP_ATOMIC, urb, slot_id, ep_index);
}
/**** Command Ring Operations ****/
/* Generic function for queueing a command TRB on the command ring.
* Check to make sure there's room on the command ring for one command TRB.
* Also check that there's room reserved for commands that must not fail.
* If this is a command that must not fail, meaning command_must_succeed = TRUE,
* then only check for the number of reserved spots.
* Don't decrement xhci->cmd_ring_reserved_trbs after we've queued the TRB
* because the command event handler may want to resubmit a failed command.
*/
static int queue_command(struct xhci_hcd *xhci, u32 field1, u32 field2,
u32 field3, u32 field4, bool command_must_succeed)
{
int reserved_trbs = xhci->cmd_ring_reserved_trbs;
int ret;
if (!command_must_succeed)
reserved_trbs++;
ret = prepare_ring(xhci, xhci->cmd_ring, EP_STATE_RUNNING,
reserved_trbs, GFP_ATOMIC);
if (ret < 0) {
xhci_err(xhci, "ERR: No room for command on command ring\n");
if (command_must_succeed)
xhci_err(xhci, "ERR: Reserved TRB counting for "
"unfailable commands failed.\n");
return ret;
}
USB: xHCI: Fix bug in link TRB activation change. Commit 6c12db90f19727c76990e7f4801c67a148b30111 introduced a bug for control transfers. The patch was supposed to change when the link TRBs at the end of each ring segment were given to the hardware. If a transfer descriptor (TD) ended just before the link TRB, the code wouldn't give back the link TRB to the hardware; instead it would be given back in prepare_ring() just before the next TD was enqueued at the top of the ring. Unfortunately, the code relied on checking the chain bit of the TRB to determine whether the TD ended just before the link TRB. It assumed that the ring enqueuing code would call prepare_ring() before enqueuing the next TD. However, control transfers are made of multiple TDs, and prepare_ring() is only called once before enqueuing two or three TDs. If the first or second TD of the control transfer ended just before the link TRB, then the code in inc_enq() would not move the enqueue pointer past the link TRB, and the link TRB would get overwritten. This would cause the xHCI driver to start writing to memory past the ring segment, and eventually the system would crash or hang. The fix is to add a flag to inc_enq() that says whether the caller will enqueue more TDs before calling prepare_ring(). If the chain bit is cleared (meaning this is the last TRB in a TD), and the caller will not enqueue more TDs, then we defer giving back the link TRB. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-06-10 19:25:28 +00:00
queue_trb(xhci, xhci->cmd_ring, false, false, field1, field2, field3,
field4 | xhci->cmd_ring->cycle_state);
return 0;
}
/* Queue a slot enable or disable request on the command ring */
int xhci_queue_slot_control(struct xhci_hcd *xhci, u32 trb_type, u32 slot_id)
{
return queue_command(xhci, 0, 0, 0,
TRB_TYPE(trb_type) | SLOT_ID_FOR_TRB(slot_id), false);
}
/* Queue an address device command TRB */
int xhci_queue_address_device(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
u32 slot_id)
{
return queue_command(xhci, lower_32_bits(in_ctx_ptr),
upper_32_bits(in_ctx_ptr), 0,
TRB_TYPE(TRB_ADDR_DEV) | SLOT_ID_FOR_TRB(slot_id),
false);
}
int xhci_queue_vendor_command(struct xhci_hcd *xhci,
u32 field1, u32 field2, u32 field3, u32 field4)
{
return queue_command(xhci, field1, field2, field3, field4, false);
}
/* Queue a reset device command TRB */
int xhci_queue_reset_device(struct xhci_hcd *xhci, u32 slot_id)
{
return queue_command(xhci, 0, 0, 0,
TRB_TYPE(TRB_RESET_DEV) | SLOT_ID_FOR_TRB(slot_id),
false);
}
USB: xhci: Bandwidth allocation support Since the xHCI host controller hardware (xHC) has an internal schedule, it needs a better representation of what devices are consuming bandwidth on the bus. Each device is represented by a device context, with data about the device, endpoints, and pointers to each endpoint ring. We need to update the endpoint information for a device context before a new configuration or alternate interface setting is selected. We setup an input device context with modified endpoint information and newly allocated endpoint rings, and then submit a Configure Endpoint Command to the hardware. The host controller can reject the new configuration if it exceeds the bus bandwidth, or the host controller doesn't have enough internal resources for the configuration. If the command fails, we still have the older device context with the previous configuration. If the command succeeds, we free the old endpoint rings. The root hub isn't a real device, so always say yes to any bandwidth changes for it. The USB core will enable, disable, and then enable endpoint 0 several times during the initialization sequence. The device will always have an endpoint ring for endpoint 0 and bandwidth allocated for that, unless the device is disconnected or gets a SetAddress 0 request. So we don't pay attention for when xhci_check_bandwidth() is called for a re-add of endpoint 0. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 02:58:38 +00:00
/* Queue a configure endpoint command TRB */
int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
u32 slot_id, bool command_must_succeed)
USB: xhci: Bandwidth allocation support Since the xHCI host controller hardware (xHC) has an internal schedule, it needs a better representation of what devices are consuming bandwidth on the bus. Each device is represented by a device context, with data about the device, endpoints, and pointers to each endpoint ring. We need to update the endpoint information for a device context before a new configuration or alternate interface setting is selected. We setup an input device context with modified endpoint information and newly allocated endpoint rings, and then submit a Configure Endpoint Command to the hardware. The host controller can reject the new configuration if it exceeds the bus bandwidth, or the host controller doesn't have enough internal resources for the configuration. If the command fails, we still have the older device context with the previous configuration. If the command succeeds, we free the old endpoint rings. The root hub isn't a real device, so always say yes to any bandwidth changes for it. The USB core will enable, disable, and then enable endpoint 0 several times during the initialization sequence. The device will always have an endpoint ring for endpoint 0 and bandwidth allocated for that, unless the device is disconnected or gets a SetAddress 0 request. So we don't pay attention for when xhci_check_bandwidth() is called for a re-add of endpoint 0. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 02:58:38 +00:00
{
return queue_command(xhci, lower_32_bits(in_ctx_ptr),
upper_32_bits(in_ctx_ptr), 0,
TRB_TYPE(TRB_CONFIG_EP) | SLOT_ID_FOR_TRB(slot_id),
command_must_succeed);
USB: xhci: Bandwidth allocation support Since the xHCI host controller hardware (xHC) has an internal schedule, it needs a better representation of what devices are consuming bandwidth on the bus. Each device is represented by a device context, with data about the device, endpoints, and pointers to each endpoint ring. We need to update the endpoint information for a device context before a new configuration or alternate interface setting is selected. We setup an input device context with modified endpoint information and newly allocated endpoint rings, and then submit a Configure Endpoint Command to the hardware. The host controller can reject the new configuration if it exceeds the bus bandwidth, or the host controller doesn't have enough internal resources for the configuration. If the command fails, we still have the older device context with the previous configuration. If the command succeeds, we free the old endpoint rings. The root hub isn't a real device, so always say yes to any bandwidth changes for it. The USB core will enable, disable, and then enable endpoint 0 several times during the initialization sequence. The device will always have an endpoint ring for endpoint 0 and bandwidth allocated for that, unless the device is disconnected or gets a SetAddress 0 request. So we don't pay attention for when xhci_check_bandwidth() is called for a re-add of endpoint 0. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-28 02:58:38 +00:00
}
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
/* Queue an evaluate context command TRB */
int xhci_queue_evaluate_context(struct xhci_hcd *xhci, dma_addr_t in_ctx_ptr,
u32 slot_id)
{
return queue_command(xhci, lower_32_bits(in_ctx_ptr),
upper_32_bits(in_ctx_ptr), 0,
TRB_TYPE(TRB_EVAL_CONTEXT) | SLOT_ID_FOR_TRB(slot_id),
false);
}
/*
* Suspend is set to indicate "Stop Endpoint Command" is being issued to stop
* activity on an endpoint that is about to be suspended.
*/
int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, int slot_id,
unsigned int ep_index, int suspend)
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
{
u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
u32 type = TRB_TYPE(TRB_STOP_RING);
u32 trb_suspend = SUSPEND_PORT_FOR_TRB(suspend);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
return queue_command(xhci, 0, 0, 0,
trb_slot_id | trb_ep_index | type | trb_suspend, false);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
/* Set Transfer Ring Dequeue Pointer command.
* This should not be used for endpoints that have streams enabled.
*/
static int queue_set_tr_deq(struct xhci_hcd *xhci, int slot_id,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
unsigned int ep_index, unsigned int stream_id,
struct xhci_segment *deq_seg,
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
union xhci_trb *deq_ptr, u32 cycle_state)
{
dma_addr_t addr;
u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
u32 trb_stream_id = STREAM_ID_FOR_TRB(stream_id);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
u32 type = TRB_TYPE(TRB_SET_DEQ);
xhci: Update internal dequeue pointers after stalls. When an endpoint stalls, the xHCI driver must move the endpoint ring's dequeue pointer past the stalled transfer. To do that, the driver issues a Set TR Dequeue Pointer command, which will complete some time later. Takashi was having issues with USB 1.1 audio devices that stalled, and his analysis of the code was that the old code would not update the xHCI driver's ring dequeue pointer after the command completes. However, the dequeue pointer is set in xhci_find_new_dequeue_state(), just before the set command is issued to the hardware. Setting the dequeue pointer before the Set TR Dequeue Pointer command completes is a dangerous thing to do, since the xHCI hardware can fail the command. Instead, store the new dequeue pointer in the xhci_virt_ep structure, and update the ring's dequeue pointer when the Set TR dequeue pointer command completes. While we're at it, make sure we can't queue another Set TR Dequeue Command while the first one is still being processed. This just won't work with the internal xHCI state code. I'm still not sure if this is the right thing to do, since we might have a case where a driver queues multiple URBs to a control ring, one of the URBs Stalls, and then the driver tries to cancel the second URB. There may be a race condition there where the xHCI driver might try to issue multiple Set TR Dequeue Pointer commands, but I would have to think very hard about how the Stop Endpoint and cancellation code works. Keep the fix simple until when/if we run into that case. This patch should be queued to kernels all the way back to 2.6.31. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Takashi Iwai <tiwai@suse.de> Cc: stable@kernel.org
2011-02-23 23:46:42 +00:00
struct xhci_virt_ep *ep;
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
addr = xhci_trb_virt_to_dma(deq_seg, deq_ptr);
if (addr == 0) {
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n");
xhci_warn(xhci, "WARN deq seg = %p, deq pt = %p\n",
deq_seg, deq_ptr);
return 0;
}
xhci: Update internal dequeue pointers after stalls. When an endpoint stalls, the xHCI driver must move the endpoint ring's dequeue pointer past the stalled transfer. To do that, the driver issues a Set TR Dequeue Pointer command, which will complete some time later. Takashi was having issues with USB 1.1 audio devices that stalled, and his analysis of the code was that the old code would not update the xHCI driver's ring dequeue pointer after the command completes. However, the dequeue pointer is set in xhci_find_new_dequeue_state(), just before the set command is issued to the hardware. Setting the dequeue pointer before the Set TR Dequeue Pointer command completes is a dangerous thing to do, since the xHCI hardware can fail the command. Instead, store the new dequeue pointer in the xhci_virt_ep structure, and update the ring's dequeue pointer when the Set TR dequeue pointer command completes. While we're at it, make sure we can't queue another Set TR Dequeue Command while the first one is still being processed. This just won't work with the internal xHCI state code. I'm still not sure if this is the right thing to do, since we might have a case where a driver queues multiple URBs to a control ring, one of the URBs Stalls, and then the driver tries to cancel the second URB. There may be a race condition there where the xHCI driver might try to issue multiple Set TR Dequeue Pointer commands, but I would have to think very hard about how the Stop Endpoint and cancellation code works. Keep the fix simple until when/if we run into that case. This patch should be queued to kernels all the way back to 2.6.31. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Tested-by: Takashi Iwai <tiwai@suse.de> Cc: stable@kernel.org
2011-02-23 23:46:42 +00:00
ep = &xhci->devs[slot_id]->eps[ep_index];
if ((ep->ep_state & SET_DEQ_PENDING)) {
xhci_warn(xhci, "WARN Cannot submit Set TR Deq Ptr\n");
xhci_warn(xhci, "A Set TR Deq Ptr command is pending.\n");
return 0;
}
ep->queued_deq_seg = deq_seg;
ep->queued_deq_ptr = deq_ptr;
return queue_command(xhci, lower_32_bits(addr) | cycle_state,
USB: xhci: Correct assumptions about number of rings per endpoint. Much of the xHCI driver code assumes that endpoints only have one ring. Now an endpoint can have one ring per enabled stream ID, so correct that assumption. Use functions that translate the stream_id field in the URB or the DMA address of a TRB into the correct stream ring. Correct the polling loop to print out all enabled stream rings. Make the URB cancellation routine find the correct stream ring if the URB has stream_id set. Make sure the URB enqueueing routine does the same. Also correct the code that handles stalled/halted endpoints. Check that commands and registers that can take stream IDs handle them properly. That includes ringing an endpoint doorbell, resetting a stalled/halted endpoint, and setting a transfer ring dequeue pointer (since that command can set the dequeue pointer in a stream context or an endpoint context). Correct the transfer event handler to translate a TRB DMA address into the stream ring it was enqueued to. Make the code to allocate and prepare TD structures adds the TD to the right td_list for the stream ring. Make sure the code to give the first TRB in a TD to the hardware manipulates the correct stream ring. When an endpoint stalls, store the stream ID of the stream ring that stalled in the xhci_virt_ep structure. Use that instead of the stream ID in the URB, since an URB may be re-used after it is given back after a non-control endpoint stall. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-04-02 22:34:43 +00:00
upper_32_bits(addr), trb_stream_id,
trb_slot_id | trb_ep_index | type, false);
USB: xhci: URB cancellation support. Add URB cancellation support to the xHCI host controller driver. This currently supports cancellation for endpoints that do not have streams enabled. An URB is represented by a number of Transaction Request Buffers (TRBs), that are chained together to make one (or more) Transaction Descriptors (TDs) on an endpoint ring. The ring is comprised of contiguous segments, linked together with Link TRBs (which may or may not be chained into a TD). To cancel an URB, we must stop the endpoint ring, make the hardware skip over the TDs in the URB (either by turning them into No-op TDs, or by moving the hardware's ring dequeue pointer past the last TRB in the last TD), and then restart the ring. There are times when we must drop the xHCI lock during this process, like when we need to complete cancelled URBs. We must ensure that additional URBs can be marked as cancelled, and that new URBs can be enqueued (since the URB completion handlers can do either). The new endpoint ring variables cancels_pending and state (which can only be modified while holding the xHCI lock) ensure that future cancellation and enqueueing do not interrupt any pending cancellation code. To facilitate cancellation, we must keep track of the starting ring segment, first TRB, and last TRB for each URB. We also need to keep track of the list of TDs that have been marked as cancelled, separate from the list of TDs that are queued for this endpoint. The new variables and cancellation list are stored in the xhci_td structure. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-04-30 02:02:31 +00:00
}
int xhci_queue_reset_ep(struct xhci_hcd *xhci, int slot_id,
unsigned int ep_index)
{
u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id);
u32 trb_ep_index = EP_ID_FOR_TRB(ep_index);
u32 type = TRB_TYPE(TRB_RESET_EP);
return queue_command(xhci, 0, 0, 0, trb_slot_id | trb_ep_index | type,
false);
}