linux/arch/x86/kernel/ftrace.c

295 lines
7.1 KiB
C
Raw Normal View History

ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
/*
* Code for replacing ftrace calls with jumps.
*
* Copyright (C) 2007-2008 Steven Rostedt <srostedt@redhat.com>
*
* Thanks goes to Ingo Molnar, for suggesting the idea.
* Mathieu Desnoyers, for suggesting postponing the modifications.
* Arjan van de Ven, for keeping me straight, and explaining to me
* the dangers of modifying code on the run.
*/
#include <linux/spinlock.h>
#include <linux/hardirq.h>
#include <linux/uaccess.h>
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
#include <linux/ftrace.h>
#include <linux/percpu.h>
#include <linux/init.h>
#include <linux/list.h>
#include <asm/ftrace.h>
#include <asm/nops.h>
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
static unsigned char ftrace_nop[MCOUNT_INSN_SIZE];
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
union ftrace_code_union {
char code[MCOUNT_INSN_SIZE];
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
struct {
char e8;
int offset;
} __attribute__((packed));
};
static int ftrace_calc_offset(long ip, long addr)
{
return (int)(addr - ip);
}
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
unsigned char *ftrace_nop_replace(void)
{
return ftrace_nop;
}
unsigned char *ftrace_call_replace(unsigned long ip, unsigned long addr)
{
static union ftrace_code_union calc;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
calc.e8 = 0xe8;
calc.offset = ftrace_calc_offset(ip + MCOUNT_INSN_SIZE, addr);
/*
* No locking needed, this must be called via kstop_machine
* which in essence is like running on a uniprocessor machine.
*/
return calc.code;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
}
ftrace: nmi safe code modification Impact: fix crashes that can occur in NMI handlers, if their code is modified Modifying code is something that needs special care. On SMP boxes, if code that is being modified is also being executed on another CPU, that CPU will have undefined results. The dynamic ftrace uses kstop_machine to make the system act like a uniprocessor system. But this does not address NMIs, that can still run on other CPUs. One approach to handle this is to make all code that are used by NMIs not be traced. But NMIs can call notifiers that spread throughout the kernel and this will be very hard to maintain, and the chance of missing a function is very high. The approach that this patch takes is to have the NMIs modify the code if the modification is taking place. The way this works is that just writing to code executing on another CPU is not harmful if what is written is the same as what exists. Two buffers are used: an IP buffer and a "code" buffer. The steps that the patcher takes are: 1) Put in the instruction pointer into the IP buffer and the new code into the "code" buffer. 2) Set a flag that says we are modifying code 3) Wait for any running NMIs to finish. 4) Write the code 5) clear the flag. 6) Wait for any running NMIs to finish. If an NMI is executed, it will also write the pending code. Multiple writes are OK, because what is being written is the same. Then the patcher must wait for all running NMIs to finish before going to the next line that must be patched. This is basically the RCU approach to code modification. Thanks to Ingo Molnar for suggesting the idea, and to Arjan van de Ven for his guidence on what is safe and what is not. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-30 20:08:32 +00:00
/*
* Modifying code must take extra care. On an SMP machine, if
* the code being modified is also being executed on another CPU
* that CPU will have undefined results and possibly take a GPF.
* We use kstop_machine to stop other CPUS from exectuing code.
* But this does not stop NMIs from happening. We still need
* to protect against that. We separate out the modification of
* the code to take care of this.
*
* Two buffers are added: An IP buffer and a "code" buffer.
*
* 1) Put in the instruction pointer into the IP buffer
* and the new code into the "code" buffer.
* 2) Set a flag that says we are modifying code
* 3) Wait for any running NMIs to finish.
* 4) Write the code
* 5) clear the flag.
* 6) Wait for any running NMIs to finish.
*
* If an NMI is executed, the first thing it does is to call
* "ftrace_nmi_enter". This will check if the flag is set to write
* and if it is, it will write what is in the IP and "code" buffers.
*
* The trick is, it does not matter if everyone is writing the same
* content to the code location. Also, if a CPU is executing code
* it is OK to write to that code location if the contents being written
* are the same as what exists.
*/
static atomic_t in_nmi;
static int mod_code_status;
static int mod_code_write;
static void *mod_code_ip;
static void *mod_code_newcode;
static int nmi_wait_count;
static atomic_t nmi_update_count;
int ftrace_arch_read_dyn_info(char *buf, int size)
{
int r;
r = snprintf(buf, size, "%u %u",
nmi_wait_count,
atomic_read(&nmi_update_count));
return r;
}
ftrace: nmi safe code modification Impact: fix crashes that can occur in NMI handlers, if their code is modified Modifying code is something that needs special care. On SMP boxes, if code that is being modified is also being executed on another CPU, that CPU will have undefined results. The dynamic ftrace uses kstop_machine to make the system act like a uniprocessor system. But this does not address NMIs, that can still run on other CPUs. One approach to handle this is to make all code that are used by NMIs not be traced. But NMIs can call notifiers that spread throughout the kernel and this will be very hard to maintain, and the chance of missing a function is very high. The approach that this patch takes is to have the NMIs modify the code if the modification is taking place. The way this works is that just writing to code executing on another CPU is not harmful if what is written is the same as what exists. Two buffers are used: an IP buffer and a "code" buffer. The steps that the patcher takes are: 1) Put in the instruction pointer into the IP buffer and the new code into the "code" buffer. 2) Set a flag that says we are modifying code 3) Wait for any running NMIs to finish. 4) Write the code 5) clear the flag. 6) Wait for any running NMIs to finish. If an NMI is executed, it will also write the pending code. Multiple writes are OK, because what is being written is the same. Then the patcher must wait for all running NMIs to finish before going to the next line that must be patched. This is basically the RCU approach to code modification. Thanks to Ingo Molnar for suggesting the idea, and to Arjan van de Ven for his guidence on what is safe and what is not. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-30 20:08:32 +00:00
static void ftrace_mod_code(void)
{
/*
* Yes, more than one CPU process can be writing to mod_code_status.
* (and the code itself)
* But if one were to fail, then they all should, and if one were
* to succeed, then they all should.
*/
mod_code_status = probe_kernel_write(mod_code_ip, mod_code_newcode,
MCOUNT_INSN_SIZE);
}
void ftrace_nmi_enter(void)
{
atomic_inc(&in_nmi);
/* Must have in_nmi seen before reading write flag */
smp_mb();
if (mod_code_write) {
ftrace: nmi safe code modification Impact: fix crashes that can occur in NMI handlers, if their code is modified Modifying code is something that needs special care. On SMP boxes, if code that is being modified is also being executed on another CPU, that CPU will have undefined results. The dynamic ftrace uses kstop_machine to make the system act like a uniprocessor system. But this does not address NMIs, that can still run on other CPUs. One approach to handle this is to make all code that are used by NMIs not be traced. But NMIs can call notifiers that spread throughout the kernel and this will be very hard to maintain, and the chance of missing a function is very high. The approach that this patch takes is to have the NMIs modify the code if the modification is taking place. The way this works is that just writing to code executing on another CPU is not harmful if what is written is the same as what exists. Two buffers are used: an IP buffer and a "code" buffer. The steps that the patcher takes are: 1) Put in the instruction pointer into the IP buffer and the new code into the "code" buffer. 2) Set a flag that says we are modifying code 3) Wait for any running NMIs to finish. 4) Write the code 5) clear the flag. 6) Wait for any running NMIs to finish. If an NMI is executed, it will also write the pending code. Multiple writes are OK, because what is being written is the same. Then the patcher must wait for all running NMIs to finish before going to the next line that must be patched. This is basically the RCU approach to code modification. Thanks to Ingo Molnar for suggesting the idea, and to Arjan van de Ven for his guidence on what is safe and what is not. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-30 20:08:32 +00:00
ftrace_mod_code();
atomic_inc(&nmi_update_count);
}
ftrace: nmi safe code modification Impact: fix crashes that can occur in NMI handlers, if their code is modified Modifying code is something that needs special care. On SMP boxes, if code that is being modified is also being executed on another CPU, that CPU will have undefined results. The dynamic ftrace uses kstop_machine to make the system act like a uniprocessor system. But this does not address NMIs, that can still run on other CPUs. One approach to handle this is to make all code that are used by NMIs not be traced. But NMIs can call notifiers that spread throughout the kernel and this will be very hard to maintain, and the chance of missing a function is very high. The approach that this patch takes is to have the NMIs modify the code if the modification is taking place. The way this works is that just writing to code executing on another CPU is not harmful if what is written is the same as what exists. Two buffers are used: an IP buffer and a "code" buffer. The steps that the patcher takes are: 1) Put in the instruction pointer into the IP buffer and the new code into the "code" buffer. 2) Set a flag that says we are modifying code 3) Wait for any running NMIs to finish. 4) Write the code 5) clear the flag. 6) Wait for any running NMIs to finish. If an NMI is executed, it will also write the pending code. Multiple writes are OK, because what is being written is the same. Then the patcher must wait for all running NMIs to finish before going to the next line that must be patched. This is basically the RCU approach to code modification. Thanks to Ingo Molnar for suggesting the idea, and to Arjan van de Ven for his guidence on what is safe and what is not. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-30 20:08:32 +00:00
}
void ftrace_nmi_exit(void)
{
/* Finish all executions before clearing in_nmi */
smp_wmb();
atomic_dec(&in_nmi);
}
static void wait_for_nmi(void)
{
int waited = 0;
while (atomic_read(&in_nmi)) {
waited = 1;
ftrace: nmi safe code modification Impact: fix crashes that can occur in NMI handlers, if their code is modified Modifying code is something that needs special care. On SMP boxes, if code that is being modified is also being executed on another CPU, that CPU will have undefined results. The dynamic ftrace uses kstop_machine to make the system act like a uniprocessor system. But this does not address NMIs, that can still run on other CPUs. One approach to handle this is to make all code that are used by NMIs not be traced. But NMIs can call notifiers that spread throughout the kernel and this will be very hard to maintain, and the chance of missing a function is very high. The approach that this patch takes is to have the NMIs modify the code if the modification is taking place. The way this works is that just writing to code executing on another CPU is not harmful if what is written is the same as what exists. Two buffers are used: an IP buffer and a "code" buffer. The steps that the patcher takes are: 1) Put in the instruction pointer into the IP buffer and the new code into the "code" buffer. 2) Set a flag that says we are modifying code 3) Wait for any running NMIs to finish. 4) Write the code 5) clear the flag. 6) Wait for any running NMIs to finish. If an NMI is executed, it will also write the pending code. Multiple writes are OK, because what is being written is the same. Then the patcher must wait for all running NMIs to finish before going to the next line that must be patched. This is basically the RCU approach to code modification. Thanks to Ingo Molnar for suggesting the idea, and to Arjan van de Ven for his guidence on what is safe and what is not. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-30 20:08:32 +00:00
cpu_relax();
}
if (waited)
nmi_wait_count++;
ftrace: nmi safe code modification Impact: fix crashes that can occur in NMI handlers, if their code is modified Modifying code is something that needs special care. On SMP boxes, if code that is being modified is also being executed on another CPU, that CPU will have undefined results. The dynamic ftrace uses kstop_machine to make the system act like a uniprocessor system. But this does not address NMIs, that can still run on other CPUs. One approach to handle this is to make all code that are used by NMIs not be traced. But NMIs can call notifiers that spread throughout the kernel and this will be very hard to maintain, and the chance of missing a function is very high. The approach that this patch takes is to have the NMIs modify the code if the modification is taking place. The way this works is that just writing to code executing on another CPU is not harmful if what is written is the same as what exists. Two buffers are used: an IP buffer and a "code" buffer. The steps that the patcher takes are: 1) Put in the instruction pointer into the IP buffer and the new code into the "code" buffer. 2) Set a flag that says we are modifying code 3) Wait for any running NMIs to finish. 4) Write the code 5) clear the flag. 6) Wait for any running NMIs to finish. If an NMI is executed, it will also write the pending code. Multiple writes are OK, because what is being written is the same. Then the patcher must wait for all running NMIs to finish before going to the next line that must be patched. This is basically the RCU approach to code modification. Thanks to Ingo Molnar for suggesting the idea, and to Arjan van de Ven for his guidence on what is safe and what is not. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-30 20:08:32 +00:00
}
static int
do_ftrace_mod_code(unsigned long ip, void *new_code)
{
mod_code_ip = (void *)ip;
mod_code_newcode = new_code;
/* The buffers need to be visible before we let NMIs write them */
smp_wmb();
mod_code_write = 1;
/* Make sure write bit is visible before we wait on NMIs */
smp_mb();
wait_for_nmi();
/* Make sure all running NMIs have finished before we write the code */
smp_mb();
ftrace_mod_code();
/* Make sure the write happens before clearing the bit */
smp_wmb();
mod_code_write = 0;
/* make sure NMIs see the cleared bit */
smp_mb();
wait_for_nmi();
return mod_code_status;
}
int
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
ftrace_modify_code(unsigned long ip, unsigned char *old_code,
unsigned char *new_code)
{
unsigned char replaced[MCOUNT_INSN_SIZE];
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
/*
* Note: Due to modules and __init, code can
* disappear and change, we need to protect against faulting
* as well as code changing. We do this by using the
* probe_kernel_* functions.
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
*
* No real locking needed, this code is run through
* kstop_machine, or before SMP starts.
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
*/
/* read the text we want to modify */
if (probe_kernel_read(replaced, (void *)ip, MCOUNT_INSN_SIZE))
return -EFAULT;
/* Make sure it is what we expect it to be */
if (memcmp(replaced, old_code, MCOUNT_INSN_SIZE) != 0)
return -EINVAL;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
/* replace the text with the new text */
ftrace: nmi safe code modification Impact: fix crashes that can occur in NMI handlers, if their code is modified Modifying code is something that needs special care. On SMP boxes, if code that is being modified is also being executed on another CPU, that CPU will have undefined results. The dynamic ftrace uses kstop_machine to make the system act like a uniprocessor system. But this does not address NMIs, that can still run on other CPUs. One approach to handle this is to make all code that are used by NMIs not be traced. But NMIs can call notifiers that spread throughout the kernel and this will be very hard to maintain, and the chance of missing a function is very high. The approach that this patch takes is to have the NMIs modify the code if the modification is taking place. The way this works is that just writing to code executing on another CPU is not harmful if what is written is the same as what exists. Two buffers are used: an IP buffer and a "code" buffer. The steps that the patcher takes are: 1) Put in the instruction pointer into the IP buffer and the new code into the "code" buffer. 2) Set a flag that says we are modifying code 3) Wait for any running NMIs to finish. 4) Write the code 5) clear the flag. 6) Wait for any running NMIs to finish. If an NMI is executed, it will also write the pending code. Multiple writes are OK, because what is being written is the same. Then the patcher must wait for all running NMIs to finish before going to the next line that must be patched. This is basically the RCU approach to code modification. Thanks to Ingo Molnar for suggesting the idea, and to Arjan van de Ven for his guidence on what is safe and what is not. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu>
2008-10-30 20:08:32 +00:00
if (do_ftrace_mod_code(ip, new_code))
return -EPERM;
sync_core();
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
return 0;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
}
int ftrace_update_ftrace_func(ftrace_func_t func)
{
unsigned long ip = (unsigned long)(&ftrace_call);
unsigned char old[MCOUNT_INSN_SIZE], *new;
int ret;
memcpy(old, &ftrace_call, MCOUNT_INSN_SIZE);
new = ftrace_call_replace(ip, (unsigned long)func);
ret = ftrace_modify_code(ip, old, new);
return ret;
}
int __init ftrace_dyn_arch_init(void *data)
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
{
extern const unsigned char ftrace_test_p6nop[];
extern const unsigned char ftrace_test_nop5[];
extern const unsigned char ftrace_test_jmp[];
int faulted = 0;
/*
* There is no good nop for all x86 archs.
* We will default to using the P6_NOP5, but first we
* will test to make sure that the nop will actually
* work on this CPU. If it faults, we will then
* go to a lesser efficient 5 byte nop. If that fails
* we then just use a jmp as our nop. This isn't the most
* efficient nop, but we can not use a multi part nop
* since we would then risk being preempted in the middle
* of that nop, and if we enabled tracing then, it might
* cause a system crash.
*
* TODO: check the cpuid to determine the best nop.
*/
asm volatile (
"ftrace_test_jmp:"
"jmp ftrace_test_p6nop\n"
"nop\n"
"nop\n"
"nop\n" /* 2 byte jmp + 3 bytes */
"ftrace_test_p6nop:"
P6_NOP5
"jmp 1f\n"
"ftrace_test_nop5:"
".byte 0x66,0x66,0x66,0x66,0x90\n"
"1:"
".section .fixup, \"ax\"\n"
"2: movl $1, %0\n"
" jmp ftrace_test_nop5\n"
"3: movl $2, %0\n"
" jmp 1b\n"
".previous\n"
_ASM_EXTABLE(ftrace_test_p6nop, 2b)
_ASM_EXTABLE(ftrace_test_nop5, 3b)
: "=r"(faulted) : "0" (faulted));
switch (faulted) {
case 0:
pr_info("ftrace: converting mcount calls to 0f 1f 44 00 00\n");
memcpy(ftrace_nop, ftrace_test_p6nop, MCOUNT_INSN_SIZE);
break;
case 1:
pr_info("ftrace: converting mcount calls to 66 66 66 66 90\n");
memcpy(ftrace_nop, ftrace_test_nop5, MCOUNT_INSN_SIZE);
break;
case 2:
pr_info("ftrace: converting mcount calls to jmp . + 5\n");
memcpy(ftrace_nop, ftrace_test_jmp, MCOUNT_INSN_SIZE);
break;
}
/* The return code is retured via data */
*(unsigned long *)data = 0;
ftrace: dynamic enabling/disabling of function calls This patch adds a feature to dynamically replace the ftrace code with the jmps to allow a kernel with ftrace configured to run as fast as it can without it configured. The way this works, is on bootup (if ftrace is enabled), a ftrace function is registered to record the instruction pointer of all places that call the function. Later, if there's still any code to patch, a kthread is awoken (rate limited to at most once a second) that performs a stop_machine, and replaces all the code that was called with a jmp over the call to ftrace. It only replaces what was found the previous time. Typically the system reaches equilibrium quickly after bootup and there's no code patching needed at all. e.g. call ftrace /* 5 bytes */ is replaced with jmp 3f /* jmp is 2 bytes and we jump 3 forward */ 3: When we want to enable ftrace for function tracing, the IP recording is removed, and stop_machine is called again to replace all the locations of that were recorded back to the call of ftrace. When it is disabled, we replace the code back to the jmp. Allocation is done by the kthread. If the ftrace recording function is called, and we don't have any record slots available, then we simply skip that call. Once a second a new page (if needed) is allocated for recording new ftrace function calls. A large batch is allocated at boot up to get most of the calls there. Because we do this via stop_machine, we don't have to worry about another CPU executing a ftrace call as we modify it. But we do need to worry about NMI's so all functions that might be called via nmi must be annotated with notrace_nmi. When this code is configured in, the NMI code will not call notrace. Signed-off-by: Steven Rostedt <srostedt@redhat.com> Signed-off-by: Ingo Molnar <mingo@elte.hu> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2008-05-12 19:20:42 +00:00
return 0;
}